Panasonic CQDF202U Operating instructions

Panasonic CQDF202U Operating instructions
E
N
G
L
I
S
H
Power and Sound Controls
1
Turn the key in the ignition until the accessory indicator lights.
Power on: Press [SOURCE] (PWR).
Power off: Press [SOURCE] (PWR) again and
hold.
Note:
≥ When the power is switched on for the first
time, a demonstration message appears on the
display.
To cancel this display, press [DISP] (display).
Clock Basics
Power
Audio Mode
(Bass/Treble/Balance/Fader)
1 Press [SEL] to select the audio mode.
ACC
ON
The 12-hour system is used for the clock.
1 Press [DISP] (CLOCK).
(Clock display.)
Bass
Treble
Fader
Balance
[% TUNE], [$ TUNE] (Hours, minutes)
SCAN/APM
CQ-DF202U
REMOTE
45W X 4
SCAN/APM
OPEN
[DISP] (CLOCK)
CQ-DF202U
REMOTE
45W X 4
OPEN
RANDOM
RANDOM
VOL
BAND
VOL
REP
PWR
TUNE
TRACK
SEL
SEL
SOURCE
CD RECEIVER
LOUD
C
MONO/LO
MUTE
7
1
8
2
9
3
10
4
11
5
CLOCK
DISP
LEVL
Level Meter (Only for main unit)
[" VOL]: Up
[# VOL]: Down
Press and hold for rapid adjustment.
When the power is on, the level of sound sources,
such as radio and CD, is displayed.
Press [LEVL] (level) to change the level meter display.
(Default)
Pattern 1
Pattern 2
Pattern off
Pattern 3
MONO
2
7
1
8
2
9
3
10
4
11
5
Press [" VOL] or [# VOL] to change each
level.
Bass:
12
6
CLOCK
DISP
LEVL
Hours
2 Press and hold [DISP] (CLOCK) for more than
2 seconds.
(Hours blink.)
Adjustable range: j12 dB to i12 dB
(by 3 dB step)
3 Press [% TUNE] or [$ TUNE].
Treble:
Adjustable range: j12 dB to i12 dB
(by 3 dB step)
(Hours set.)
Minutes
4 Press [DISP] (CLOCK).
(Minutes blink.)
Balance:
Display Change
R (right speaker) or L (left speaker)
Press [DISP] (CLOCK) to switch to the clock display.
LOUD
Press [LOUD] again to cancel.
SOURCE
CD RECEIVER
Pattern 4
Loudness (Only for main unit)
Press [LOUD] to enhance bass and treble
tones at low or medium volume.
REP
PWR
TUNE
TRACK
C
MONO/LO
MUTE
Volume
Volume level (0 to 40)
BAND
LOUD
12
6
5 Press [% TUNE] or [$ TUNE].
(Minutes set.)
Adjustable range:
1 to 15 (by 1 dB step)
When the power is off:
Balance center
6 Press [DISP] (CLOCK).
Fader:
No display
Mute
Clock display
(End.)
F (front speaker) or R (rear speaker)
Press [MUTE] to mute the sound completely.
MUTE
Press [MUTE] again to cancel.
10
CQ-DF202U
2
Initial Time
Regular mode
Volume
E
N
G
L
I
S
H
Anti-volume-blast circuit:
When the power is switched off and on again,
the volume slowly rises to the previous level.
The anti-volume-blast circuit will not work when
the volume level is set lower than position 20 on
the display.
Adjustable range:
1 to 15 (by 1 dB step)
Fader center
Note:
≥ If no operation takes place for more than 5 seconds
in audio mode (2 seconds in volume mode), the display returns to the regular mode.
Note:
≥ Press and hold [% TUNE] or [$ TUNE] for more
than 2 seconds to change numbers rapidly.
Time Reset
Press and hold [DISP] (CLOCK) for more than
2 seconds to activate the time setting mode to
reset the time.
Then, repeat steps 3 to 6.
CQ-DF202U
11
Radio Basics
E
N
G
L
I
S
H
Mode
1 Radio
Press [SOURCE] to change to
3
Source
Radio
the radio mode.
CD player
(When a CD is inserted.)
Preset Station Setting
Display Change
Up to 6 stations each can be saved in the FM1,
FM2, FM3 and AM preset station memories.
Press [DISP] (CLOCK) to switch to the clock display.
Note:
≥ New stations are overwritten on existing saved
stations after following this procedure.
2 Band
Press [BAND] to change the band.
E
N
G
L
I
S
H
Broadcast station
4
Clock display
1 Band
Press [BAND] to select a desired band.
(➡ page 12)
Preset number
FM stereo indicator
SCAN/APM
CQ-DF202U
REMOTE
L
VOL
SEL
ST MONO
BAND
LOCAL TAon AF ΙΙ PTY
45W X 4
RDS
EON
TP
SCAN/APM
OPEN
L
VOL
REP
DISC
TUNE
TRACK
MUTE
LOUD REP RAND
PWR
SEL
SOURCE
C
MONO/LO
MUTE
7
1
8
2
9
3
10
4
11
5
12
6
CLOCK
DISP
LOCAL TAon AF ΙΙ PTY
45W X 4
RDS
EON
TP
OPEN
RANDOM
R
REP
DISC
TUNE
TRACK
LOUD REP RAND
MUTE
PWR
SOURCE
CD RECEIVER
LOUD
LEVL
ST MONO
BAND
CD RECEIVER
LOUD
CQ-DF202U
REMOTE
RANDOM
R
C
MONO/LO
MUTE
7
1
8
2
9
3
10
4
11
5
12
6
CLOCK
DISP
LEVL
Preset buttons [1] to [6]
Tuning
3 Manual
[$ TUNE]: Higher frequency
2 Auto Preset Memory (APM)
Press and hold [BAND] (APM: auto preset
memory) for more than 2 seconds.
≥ The 6 strongest available stations will be
automatically saved in the memory under
preset buttons [1] to [6].
≥ Once set, the preset stations are sequentially scanned for 5 seconds each.
[% TUNE]: Lower frequency
Seek Tuning
Press and hold ...
[$ TUNE]: Higher frequency
[% TUNE]: Lower frequency
Tuning will automatically stop when
the signals of the next broadcast
station are received.
12
Manual Preset Memory
FM broadcast:
Mono/Local Selection
4 MONO: Noise is significantly decreased when weak
ST MONO
LOCAL
signals are received from an FM broadcast
station.
LOCAL: Only strong signals of stations are searched
in seek tuning, while at the LOCAL OFF setting, relatively weak signals are also
searched.
FM broadcast:
Press and hold [MUTE] (MONO/LOC) for more than
2 seconds to change the mode.
Release when at the desired point.
AM broadcast:
Press and hold [MUTE] (MONO/LOC) for more than
2 seconds to switch LOCAL mode on and off.
ST MONO
LOCAL
ST MONO
LOCAL
ST MONO
LOCAL
CQ-DF202U
MONO off/
LOCAL off
(Default)
MONO on/
LOCAL off
MONO on/
LOCAL on
MONO off/
LOCAL on
AM broadcast:
ST MONO
LOCAL
ST MONO
LOCAL
1 Use manual or seek tuning to find a station. (➡ page 12)
2 Press and hold one of the preset buttons
[1] to [6] until the display blinks once.
Preset Station Calling
Press the corresponding preset button [1] to [6] to
tune in a preset station.
Caution:
≥ To ensure safety, never attempt to preset stations while you are driving.
LOCAL off
(Default)
LOCAL on
CQ-DF202U
13
CD Player Basics
E
N
G
L
I
S
H
Disc Insert and Playback
Caution:
≥ Only 5z (12 cm) CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
≥ This unit does not support CD text display.
≥ This unit does not support MP3 disc playback.
≥ Refer to page 21 about notes on CD-R/RWs.
≥ This unit is not designed for any 3z (8 cm) disc.
≥ If you insert an 3z (8 cm) disc and can not eject it, turn ACC of your car off once and turn it on again, then
press [<] (eject).
≥ Do not use irregular shaped discs.
≥ Do not use discs that have a seal or label attached.
≥ Do not insert foreign matter into the disc slot.
5
Note:
≥ Do not insert a disc when the indicator lights.
DISC
the front panel
1 Open
Press [OPEN] to open the front panel.
< (Eject)
insert
2 Disc
Playback will start automatically after the player recognized the loaded disc as an ordinary
music CD. (When a CD-R or CD-RW which
has CD-DA formatted data as the same as an
ordinary music CD is loaded, this player recognizes it as an ordinary music CD.)
Close the front panel manually.
Label side
Close
Stop and Disc Eject
Track Selection
Direct Track Selection
[5TRACK]: Advance to the next track.
[6TRACK]: Back to beginning of the current track.
Back to previous track. (Press
twice.)
≥ Press a track number button from [1] to [6].
The corresponding track starts playing.
≥ Press and hold a track number button from [7] to
[12] ([1] to [6]) for more than 1 second.
The corresponding track starts playing.
Press and hold ...
[5TRACK]: Fast forward
[6TRACK]: Fast backward
Release to resume the regular play.
Listening to a CD
CD Player Mode (When a CD is in the player)
SCAN/APM
VOL
CD player
(When a CD is inserted.)
45W X 4
OPEN
BAND
REP
PWR
TUNE
TRACK
SOURCE
CD RECEIVER
LOUD
C
MONO/LO
MUTE
<CD player display>
Track number
Track playing time
CQ-DF202U
REMOTE
45W X 4
L
VOL
CQ-DF202U
REMOTE
RANDOM
SEL
OPEN
RANDOM
R
BAND
REP
DISC
TUNE
TRACK
SEL
Random play
Repeat play
Scan play
Press [SOURCE] to change to the CD play mode.
Playback will start automatically.
SCAN/APM
6
Track Search
1 Press [OPEN] on the front panel.
2 Press [<] (eject) to stop CD play and eject the disc.
Source
Radio
E
N
G
L
I
S
H
PWR
SOURCE
Random play
CD RECEIVER
LOUD
C
MONO/LO
MUTE
7
1
8
2
9
3
10
4
≥ Do not insert a disc when the indicator lights.
≥ Lights when the disc is loaded.
11
5
12
6
CLOCK
DISP
LEVL
Scan play
Display Change
7
1
8
2
9
3
10
4
11
5
12
6
CLOCK
DISP
LEVL
≥ Press and hold [REP] (RANDOM) for
more than 2 seconds.
All the tracks are played in random order.
≥ Press and hold [REP] (RANDOM) again
to cancel.
≥ Press [BAND] (SCAN).
The first 10 seconds of each track on the
disc are played in sequence.
≥ Press [BAND] (SCAN) again to cancel.
DISC
RAND
Lights.
DISC
Blinks.
Press [DISP] (CLOCK) to switch to the clock display.
Repeat play
Track number/
Track playing time
14
CQ-DF202U
Clock display
≥ Press [REP].
The current track is repeated.
≥ Press [REP] again to cancel.
DISC
REP
Lights.
CQ-DF202U
15
E
N
G
L
I
S
H
Remote Control Unit Preparation
7
1 Remove the battery holder.
Pull the battery holder by the position B while pushing position A in the direction indicated by the arrow.
2 Install the battery on the battery holder.
As shown in the figure on the right, fit the battery into
the battery holder with the “i” side facing up while
pressing on position A.
3 Insert the battery holder.
Push the battery holder back into its original position.
Battery Installation
Battery Notes
Troubleshooting
Preliminary Steps
Lithium battery
(included)
Check and take steps as described in the tables below.
Back side
If You Suspect Something Wrong
Immediately switch the power off.
Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs.
Never try to repair the unit yourself because it is dangerous to
do so.
Position B
Battery holder
Trouble
Cables are not correctly connected.
➡Connect cables correctly.
Battery cable is not correctly connected.
➡Connect the battery cable to the terminal that is always active.
No power.
Control Reference Guide
SCAN/APM
CQ-DF202U
REMOTE
Fuse is burnt out.
➡Call the store where you purchased the unit, or your nearest
Servicenter (see the attached sheet) and ask for fuse replacement.
BAND
TUNE
TRACK
CD RECEIVER
LOUD
C
MONO/LO
MUTE
7
1
8
2
9
3
10
4
11
5
1
6
(ATT)
Mode (source) button (MODE)
(➡ pages 12, 14)
Band button (BAND)
(➡ page 12)
MUTE
Mute button (MUTE)
(➡ page 10)
VOL
PRG
Volume control buttons (VOL, " #)
(➡ page 10)
No sound.
Tune/track selection and search buttons
(TUNE/TRACK, 6 5/% $)
(➡ pages 12, 15)
Car Audio
Cables are not correctly connected.
➡Connect cables correctly.
Condensation (dew).
➡Wait for a while before use.
BAND/DISC UP
Note:
≥ Disc up button (DISC UP)
cannot be used in this
model.
CQ-DF202U
Mute is set to ON.
➡Set it to OFF.
MODE
TUNE
TRACK
16
Accessory cable is not correctly connected.
➡Connect the accessory cable to your car’s ACC source.
Grounding wire is not correctly connected.
➡Connect the grounding wire to a metal part of the car.
Buttons of the remote control function in the same way as the controls on the main unit of the reference page.
Point the remote control unit at the main unit’s sensor (REMOTE).
PWR
Cause/Step
Car’s engine switch is not on.
➡Turn your car’s ignition switch to ACC or ON.
≥ Do not disassemble or short the battery. Do not throw a battery into a fire.
≥ Keep batteries away from children to avoid the risk of accidents.
≥ Be careful to observe proper local disposal rules when you dispose of batteries.
Power button (PWR)
(➡ page 10)
8
❐ Common
Caution:
≥ Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire.
Battery leakage may damage the unit.
SEL
Caution:
≥ Do not use the unit if it malfunctions or
is something wrong.
≥ Do not use the unit in abnormal condition, for example, without sound, or with
smoke or foul smell, which can cause ignition or electric shock. Immediately
stop using it and call the store where
you purchased it.
Troubleshooting Tips
Position A
Remove and dispose of an old battery immediately.
Battery Information:
≥ Battery type: Panasonic lithium battery (CR2025) (included)
≥ Battery life: Approximately 6 months with normal use (at room temperature)
VOL
E
N
G
L
I
S
H
Noise.
A mobile phone is used near the unit.
➡Keep the mobile phone away from the unit.
Audio sound is output
but the display shows
demonstration message.
Demonstration mode is ON.
➡Press [DISP] (display) to cancel demonstration mode.
CQ-DF202U
17
Troubleshooting (Continued)
E
N
G
L
I
S
H
❐ Radio
9
❐ CD (Continued)
Trouble
Cause/Step
Station is too far, or signals are too weak.
➡Select other stations of higher signal level.
Much noise in FM stereo
and monaural broadcasts.
The motor antenna relay control lead is not connected correctly.
➡If there is a motor antenna in the car, connect the motor antenna
relay control lead to the motor antenna lead that is installed in the
car correctly.
The radio antenna is not extended enough.
➡Fully extend the radio antenna.
Preset station is reset.
Trouble
≥ Disc is dirty.
≥ Disc has scratches.
➡Clean disc, referring to the section on “Notes on CD/CD Media (CDR, CD-RW)”.
Sound skips, bad sound
quality. (e.g. caused by
noise)
CQ-DF202U
Sound skips due to vibration.
Mounting angle is over 30o.
➡Adjust mounting angle to less than 30o.
Instable mounting.
➡Mount the unit securely with the mounting parts, referring to the
section on installation.
Disc is not ejected.
≥ Disc is defective.
≥ Mechanical trouble.
➡Press [OPEN] to open the panel and press [<] (eject). If normal operation is not restored, call the store where you purchased the unit
or the nearest Servicenter to ask for repairs.
Time is counted but no
sound comes out.
The first track of a mix mode disc was reproduced. (Mix mode is a format in which data except music is recorded on the first track and music
data is recorded on other than the first track in a session.)
➡Play back music data recorded on other than the first track.
❐ Sound Setting
Trouble
No sound from
right, front or
speakers.
Cause/Step
left,
rear
A disc that has data other than CD-DA type is loaded.
➡Discs that have CD-DA type data should be used.
➡The unit may not be successfully play back a CD-R/RW that was
made by the combination of writing software, a CD recorder (CD-R/
RW drive) and a disc if they are incompatible one another. Refer to
instructions for the concerned devices for details.
10
Cause/Step
Cause/Step
Disc is upside down.
➡Place disc in the correct direction with the label side up.
Disc is in the CD compartment but no sound is
made, or disc is ejected
automatically.
Trouble
Battery cable is not correctly connected.
➡Connect the battery cable to the terminal that is always active.
❐ CD
18
E
N
G
L
I
S
H
Left and right sounds
are reversed in stereo
listening.
Left and right balance, or front and rear balance is off on one side.
➡Adjust balance/fader setting as appropriate.
Cables are not correctly connected.
➡Connect the cables correctly.
The right speaker wire is connected to the left speaker and the left
speaker wire to the right speaker.
➡Connect the speaker wires to the correct ones.
≥ Disc is dirty.
≥ Disc has scratches.
➡Clean disc, referring to the section on “Notes on CD/CD Media (CDR, CD-RW)”.
➡The unit may not be successfully play back a CD-R/RW that was
made by the combination of writing software, a CD recorder (CD-R/
RW drive) and a disc if they are incompatible one another. Refer to
instructions for the concerned devices for details.
CQ-DF202U
19
Troubleshooting (Continued)
E
N
G
L
I
S
H
Maintenance
❐ Remote Control Unit
11
Care of the Unit
Trouble
Cause/Step
Battery polarities are reversed.
➡Insert the battery correctly.
Buttons are invalid for
operation.
E
N
G
L
I
S
H
12
❐ Cleaning this Unit
❐ Caution on Cleaning
Use a dry, soft cloth to wipe.
Never use solvents such as benzine, thinner as they
may mar the surface of the unit.
Notes on CD/CD Media (CD-R, CD-RW)
Wrong the battery used.
➡Check the battery.
Do not play any ordinary music CDs with labels
other than this one.
Battery has run down.
➡Replace the battery.
Remote control unit is in the wrong direction.
➡Direct the remote control unit at sensor (REMOTE) on the front
panel.
Error Display Messages
❐ CD
How to hold the disc
≥ Do not touch the underside of the disc.
≥ Do not scratch the discs.
≥ Do not bend disc.
≥ When not in use, keep the disc in the case.
Label side
Do not use irregular shaped discs.
Display
Cause/Step
≥ Disc is dirty, or is upside down.
≥ A disc that has data other than CD-DA type is loaded.
➡Check disc.
Disc has scratches.
➡Check disc.
No operation by some cause.
➡If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs.
Do not leave discs on the following places:
≥ Direct sunlight
≥ Near car heaters
≥ Dirty, dusty and damp areas
≥ Seats and dashboards
Do not use irregular shaped discs.
<Right>
<Wrong>
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Caution on new discs
A new disc may have rough edges on its inner and outer
perimeter. These may cause malfunction.
Remove the rough edges using a pencil, etc.
Rough edges
Do not attach any seals or labels to your discs.
Maintenance
Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry, a soft cloth for
routine exterior cleaning. Never use benzine, thinner or other solvents.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Servicenter. The product should be serviced only by a qualified technician.
Replace the Fuse
Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the product directly without a fuse, could cause fire or damage to the stereo unit.
If the replacement fuse fails, contact your nearest Panasonic Servicenter for service.
20
CQ-DF202U
Do not write on the disc label in a heavy pen or ballpoint pen stroke.
Notes on CD-Rs/RWs
≥ You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
≥ CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving
them inside a car for extended periods may damage them and make playback impossible.
≥ The unit may not successfully play back a CD-R/RW that was made by the combination of writing software, a
CD recorder (CD-R/RW drive) and a disc if they are incompatible one another.
≥ This player cannot play CD-R/RW discs if the session is not closed.
≥ This player cannot play the CD-R/RW discs which contains other than CD-DA data.
≥ Be sure to observe the instructions of CD-R/RW disc for handling it.
CQ-DF202U
21
Installation Guide
E
N
G
L
I
S
H
❐ Identify All Leads
WARNING
13
This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product.
Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death.
❐ Installation Hardware
If you encounter problems, please consult your
nearest professional installer.
No.
Item
1
Mounting collar
1
2
Hex. nut (5 mm·)
1
3
Rear support strap
1
Before you begin installation, look for the items
which are packed with your unit.
4
Tapping screw
(5 mm·a16 mm)
1
5
Mounting bolt (5 mm·)
1
6
Power connector
1
≥ Warranty Card…Fill this out promptly.
≥ Panasonic Servicenter List for Service Directory
…Keep for future reference in case the product
needs servicing.
≥ Installation Hardware…Needed for in-dash installation.
7
Removable face plate case
1
8
Trim plate
Diagram
Q’ty
1
Caution:
≥ This unit operates with a 12 V DC negative
ground auto battery system only. Do not attempt to use it in any other system. Doing so
could cause serious damage.
❐ Required Tools
You’ll need a screwdriver, a 1.5 V AA battery, and
the following:
12 V DC
Electrical
Side-cut
Test bulb
tape
pliers
❐ Overview
This product should be installed by a professional.
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
instructions in these pages will guide you through
the remaining steps:
(Please refer to the “WARNING” statement
above.)
≥ Identify and label the car wires.
≥ Connect the car wires to the wires of the power
connector.
≥ Install the unit in the dashboard.
≥ Check the operation of the unit.
22
CQ-DF202U
The first step in installation is to identify all the car
wires you’ll use when hooking up your sound system.
As you identify each wire, we suggest that you label
it using masking tape and a permanent marker.
This will help avoid confusion when making connections later.
Note:
≥ Do not connect the power connector to the stereo
unit until you have made all connections. If there
are no plastic caps on the stereo hooking wires,
insulate all exposed leads with electrical tape until
you are ready to use them. Identify the leads in
the following order.
Power Lead
If your car has a radio or is pre-wired for one:
Cut the connector wires one at a time from the plug
(leaving the leads as long as possible) so that you
can work with individual leads.
Turn the ignition on to the accessory position, and
ground one lead of the test bulb to the chassis.
Touch the other lead of the test bulb to each of the
exposed wires from the cut radio connector plug.
Touch one wire at a time until you find the outlet
that causes the test bulb to light.
Now turn the ignition off and then on. If the bulb
also turns off and on, that outlet is the car power
lead.
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for radio
(RADIO), accessory (ACC), or ignition (IGN).
❐ Dashboard Specifications
Thickness
Min. 3⁄16z (4.75 mm)
Max. 7⁄32z (5.56 mm)
23⁄32z (53 mm)
75⁄32z (182 mm)
Battery Lead
If your stereo unit has a yellow lead, you will need
to locate the car’s battery lead. Otherwise you may
ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function.)
If your car has a radio or is pre-wired for one:
With the ignition and headlights off, identify the car
battery lead by grounding one lead of the test bulb
to the chassis and checking the remaining exposed
wires from the cut radio connector plug.
E
N
G
L
I
S
H
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for the
battery, usually marked BAT.
14
Speakers
Identify the car speaker leads. There are two leads
for each speaker which are usually color coded.
A handy way to identify the speaker leads and the
speaker they are connected with is to test the leads
using a 1.5 V AA battery as follows.
Hold one lead against one pole of the battery and
stroke the other lead across the other pole. You will
hear a scraping sound in one of the speakers if you
are holding a speaker lead.
If not, keep testing different lead combinations until
you have located all the speaker leads. When you
label them, include the speaker location for each.
Antenna Motor
If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead
and touching the remaining exposed wires from the
cut radio connector plug one at a time. You will
hear the antenna motor activate when you touch
the correct wire.
Antenna
The antenna lead is a thick, black wire with a metal
plug at the end.
❐ Connect All Leads
Now that you have identified all the wires in the car,
you are ready to begin connecting them to the
stereo unit wires. The wiring diagram (➡ page 28)
shows the proper connections and color coding of
the leads.
We strongly recommend that you test the unit before making a final installation.
You can set the unit on the floor and make temporary connections to test the unit. Use electrical tape
to cover all exposed wires.
Important:
≥ Connect the red power lead last, after you
have made and insulated all other connections.
Ground
Connect the black ground lead of the power connector to the metal car chassis.
CQ-DF202U
23
Installation Guide (Continued)
E
N
G
L
I
S
H
Speakers
Connect the speaker wires. See the wiring diagram
(➡ page 28) for the proper hookups. Follow the diagram carefully to avoid damaging the speakers
and the stereo unit.
The speakers used must be able to handle more
than 45 W of audio power. If using an optional
audio amplifier, the speakers should be able to handle the maximum amplifier output power. Speakers
with low input ratings can be damaged. Speaker
impedance should measure 4–8 ≠, which is typically marked on most speakers. Lower or higher
impedance speakers will affect output and can
cause both speaker and stereo unit damage.
15
Motor Antenna
Connect the car motor antenna lead to the dark blue
motor antenna relay control lead.
Battery
Connect the yellow battery lead to the correct radio
wire or to the battery fuse port on the fuse block.
Antenna
Connect the antenna by plugging the antenna lead
into the antenna receptacle.
Equipment
Connect any optional equipment such as an amplifier, according to the instructions furnished with the
equipment. Leave about 12z (30 cm) of distance
between the speaker leads/amplifier unit and the
antenna/antenna extension cord. Read the operating and installation instructions of any equipment
you will connect to this unit.
Power
Connect the red power lead to the correct car radio
wire or to the appropriate fuse port on the fuse
block.
If the stereo unit functions properly with all these
connections made, disconnect the wires and proceed to the final installation.
❐ Final Installation
Lead Connections
Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires
and fasten them with tape so they will not fall down
later. Now insert the stereo unit into the mounting
collar.
Congratulations! After making a few final checks,
you’re ready to enjoy your new auto stereo system.
24
CQ-DF202U
E
N
G
L
I
S
H
❐ Final Checks
❐ Installation Procedures
1. Make sure that all wires are properly connected
and insulated.
2. Make sure that the stereo unit is securely held in
the mounting collar.
3. Turn on the ignition to check the unit for proper
operation.
First complete the electrical connections, and
then check them for correctness. (➡ page 28)
mounting collar 1 into the dashboard, and
1 Insert
bend the mounting tabs out with a screwdriver.
16
Make sure that the lock lever (§) is flush with the
mounting collar 1 (not projecting outward).
Lock lever
If you have difficulties, consult your nearest authorized professional installer for assistance.
❐ Preparation
≥ We strongly recommend that you wear gloves
for installation work to protect yourself from
injuries.
≥ When bending the mounting tabs of the
mounting collar with a screwdriver, be careful
not to injure your hands and fingers.
Lock lever (§)
6 Power connector
≥ Disconnect the cable from the negative - battery
terminal (see cautions below).
≥ Unit should be installed in a horizontal position
with the front end up at a convenient angle, but
not more than 30o.
Mounting tabs
5 Mounting bolt (5 mm·)
the rear of the unit.
2 Secure
After fixing mounting bolt 5 and power connector
6, fix the rear of the unit to the car body by either
method (a) or (b) shown below.
3 Insert trim plate 8.
installation, re4 After
connect the negative -
Less than 30x
Caution:
≥ Do not disconnect the battery terminals of a
car with a trip or navigational computer since
all user settings stored in memory will be lost.
Instead take extra care with installing the unit
to prevent shorts.
battery terminal.
(a) Using the rear support strap 3
Fire wall of car
Dashboard Installation
4 Tapping screw
(5 mm·a16 mm)
Installation Opening
23/32q
(53 mm)
75/32q
(182 mm)
This unit can be installed in any dashboard having
an opening as shown above. The dashboard should
be 3⁄16z (4.75mm)j7⁄32z (5.56 mm) thick in order to
be able to support the unit.
3 mm·
(b) Using the rubber cushion (option)
Rear support bracket
Rubber cushion (option) (provided on the car)
2 Hex. nut
(5 mm·)
3 Rear support
strap
5 Mounting bolt
(5 mm·)
5 Mounting bolt
(5 mm·)
1 Mounting collar
1 Mounting collar
CQ-DF202U
25
E
N
G
L
I
S
H
17
Installation Guide (Continued)
Anti-Theft System
Remove the Unit
This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable.
The security indicator will blink.
Switch off the power of the unit.
Remove the removable face plate.
1 Press [OPEN]. The removable face plate will
be opened.
1
45W X 4
OPEN
Main unit
1 Open
Contact
[OPEN]
RANDOM
2 Push
REP
PWR
SOURCE
3 Pull out
Place the Removable Face
Plate into Case
E
N
G
L
I
S
H
18
7 Removable face plate case
1 Switch off the power of the unit.
2 Remove the removable face plate. (➡ page 26)
3 Gently press the bottom of the case and open
the cover. Place the face plate into the case and
take it with you when you leave the car.
2 Push the face plate to the left.
3 Pull it out toward you.
Install Removable Face Plate
2
Remove the trim plate 8 with a screwdriver.
8 Trim plate
Screwdriver
1
2
out the unit while pushing down the lock
3 Pull
lever with a screwdriver.
Lock lever
1 Fit the face plate with its left hole on one of the
pins provided on the main unit.
2 Fit the other hold on the other pin applying
slight pressure.
3 Move the face plate up and down a few times to
make sure it is secure. Then close the front
panel and press down the right side of the face
plate until it clicks into plate.
Contact
1
3
2
Security Indicator
The security indicator blinks when the removable
face plate is removed from the unit.
Press and hold [SEL] to turn the security indicator
on or off. (“LED ON” or “LED OFF”)
Default
Display
Security indicator
Security indicator
Blinks
Lock lever
4
26
Remove the unit pulling with both hands.
CQ-DF202U
OFF
Caution:
≥ This face plate is not waterproof. Do not expose it to water or excessive moisture.
≥ Do not remove the face plate while driving your car.
≥ Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.
≥ Do not touch the contacts on the face plate or the main unit, since this may result in poor electrical contacts.
≥ If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.
≥ Do not apply a strong downward force onto the face plate and do not put anything on it while it is open, or
it might be damaged.
CQ-DF202U
27
Electrical Connections
E
N
G
L
I
S
H
Specifications
Caution:
≥ This product is designed to operate with a 12 V DC, negative ground battery system.
≥ To prevent damage to the unit, be sure to follow the connection diagram below.
≥ Remove approximately 1⁄4z (5 mm) of protective covering from the ends of the leads before connecting.
≥ Do not insert the power connector into the unit until the wiring is completed.
≥ Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables
and keep cable terminals free from touching any metal parts.
≥ Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
19
Supplied hardware
No.
Item
Q’ty
6
Power connector
1
CQ-DF202U (rear)
Antenna
Motor antenna
(Dark blue)
(Max. 500 mA)
relay control lead
(To motor antenna)
This lead is not intended for use with switch actuated
power antenna.
Amp. relay control power lead
This lead is for connection to the power amplifier.
Battery lead
To the car battery,
continuous +12 V DC
BATTERY 15A
Fuse (15 A)
(Yellow)
ACC
Resistor (1 k≠)
(Red)
Power lead
To ACC power,
+12 V DC
Speaker lead
FRONT SP
(White/black
stripe)
(s)
(White) (Gray/black
stripe)
(r)
(s)
(Gray)
(r)
12 V DC (11 Vj16 V), test voltage 14.4 V, negative ground
Less than 2.2 A (CD play mode; 0.5 Wa4 channels)
45 Wa4 channels at 400 Hz, volume control maximum
20
n12 dB at 100 Hz
n12 dB at 10 kHz
4j8 ≠
2.0 V (CD play mode; 1 kHz, 0 dB)
200 ≠
7za115/16 za57/8 z (178a50a150 mm)
3 lbs. 1 oz (1.4 kg)
REAR SP
(Green/black
stripe)
(s)
(Green)
(r)
87.9 MHzj107.9 MHz
11.0 dBf. (1.25 ¨V, 75 ≠)
15.2 dBf. (1.6 ¨V, 75 ≠)
30 Hzj15 kHz (n3 dB)
75 dB
42 dB (1 kHz)
75 dB
100 dB
70 dB
❐ AM Radio
6 Power connector
(Black)
Power supply:
Current consumption:
Maximum power output:
Tone adjustment range:
Bass:
Treble:
Suitable speaker impedance:
Preamp output voltage:
Output impedance:
Dimensions (WaHaD):
Weight:
Frequency range:
Usable sensitivity:
50 dB quieting sensitivity:
Frequency response:
Alternate channel selectivity:
Stereo separation:
Image response ratio:
IF response ratio:
Signal/noise ratio:
L (White)
R (Red)
Ground lead
To a clean, bare metallic part of car chassis.
❐ General
❐ FM Stereo Radio
❐ Wiring Diagram
Preamp out connector (front)
Preamp out connector (rear)
E
N
G
L
I
S
H
(Violet/
(Violet)
black
stripe) (s) (r)
Frequency range:
Usable sensitivity:
530 kHzj1 710 kHz
28 dB/¨V (25 ¨V, S/N 20 dB)
❐ CD Player
Sampling frequency:
DA converter:
Error correction system:
Pick-up type:
Light source:
Wave length:
Frequency response:
Signal/noise ratio:
Total harmonic distortion:
Wow and flutter:
Channel separation:
32 times oversampling
MASH·1 bit/4 DAC system
Panasonic super decoding algorithm
Astigma 3-beam
Semiconductor laser
780 nm
20 Hzj20 kHz (n1 dB)
96 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
Above specifications comply with EIA standards.
Note:
≥ Specifications and the design are subject to modification without notice due to improvements in technology.
Left speaker
(front)
28
CQ-DF202U
Right speaker
(front)
Left speaker
(rear)
Right speaker
(rear)
CQ-DF202U
29
MEMO
70
CQ-DF202U
CQ-DF202U
71
Panasonic Consumer
Electronics Company, Division
of Matsushita Electric
Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.com
Panasonic Sales Company.
Division of Matsushita Electric
of Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
http://www.panasonic.com
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
http://www.panasonic.ca
YEFM283816
F1101-0
Printed in China
Imprimé en Chine
Impreso en China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement