Panasonic CQVD7003N Operating Instructions

English
Safety Information
1
CAUTION:
• PLEASE FOLLOW THE LAWS AND REGULATIONS
OF YOUR STATE, PROVINCE OR COUNTRY FOR
INSTALLATION OF THE UNIT.
• TO
REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE
THIS APPLIANCE TO RAIN, SPLASHING, DRIPPING OR MOISTURE.
2
CQ-VD7003N
English
Upgrade Options
2
Display Unit
Rear Monitor
CQ-VD7003N
TV Tuner
(CY-TUP153N, option)
iPod®
Hands-Free Kit featuring
Bluetooth® technology
(CY-BT100N, option)
Expansion Module
(CY-EM100N, option)
CD Changer
(CX-DP880N, option)
DVD Changer
(CX-DH801N, option)
Car Navigation System
(CN-DV2300N, option)
Contents
Safety Information................................................2
Upgrade Options ..................................................3
Contents................................................................3
Installation ............................................................4
Electrical Connections ......................................10
CQ-VD7003N
3
English
Installation
3
Preparation
Caution
¡Please follow the laws and regulations of your
province or country for installation of the unit.
¡When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
¡We strongly recommend you to wear gloves for
installation work to protect yourself from injuries.
Dashboard Installation
Installation Opening
The unit can be installed in any dashboard having an
opening as shown below. The dashboard should be 4.5
mm – 6 mm thick in order to be able to support the unit.
53 mm
182 mm
¡Before installation, check the radio operation with
antenna and speakers.
¡Disconnect the cable from the negative (–) battery terminal (see caution below).
¡The unit should be installed in a horizontal position
with the front end up at a convenient angle, but not
more than 30°.
Installation Precautions
This product should be installed by a professional
installer, if possible.
In case of difficulty, please consult your nearest authorized Panasonic Service Centre.
1. This system is to be used only in a 12 V DC battery
system (car) with negative ground.
0 – 30°
2. Follow the electrical connections carefully (a page
10-19). Failure to do so may result in damage to the
unit.
3. Connect the power lead after all other connections are
made.
4. Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal.
Caution
¡Do not disconnect the battery terminals of a car with
trip or navigational computer since all user settings
stored in memory will be lost. Instead take extra
care with installing the unit to prevent shorts.
4
CQ-VD7003N
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before connecting it to this unit.
No.
Item
English
❏ Installation Hardware
(For Installation)
❏ Installation Hardware
(For Wiring)
Diagram
q Trim Plate
Qty.
1
(YFC054C087CA)
w Mounting Collar
No.
Item
e Mounting Spring
1
!1 Clip Connector
1
(YAJ024C118ZA)
!2 Reverse Extension Cord
2
(YFX054C077CA)
r Mounting Bolt (5 mmø)
Qty.
!0 Power Connector
1
(YFX214C433CA)
4
Diagram
1
(YEAJ012897)
!3 ISO Antenna Adapter
1
1
(YEAA33144)
(YEJVO1060)
Round Head Screw
(5 mmø x 6 mm)
Flat-Head Screw
y
(5 mmø x 6 mm)
Round Head Screw
u
(4 mmø x 3 mm)
t
2
4
4
(ZZBISVD7001B)
i Spacer
2
1
set
o Double-Faced Adhesive Tape
Note:
¡The number in parenthesis underneath each accessory
part name is the part number for maintenance and service.
¡Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
¡Use the supplied screws for installation exclusively. In
case of losing any of them, please order the specific
screw.
(ZZBISVD7001E)
❏ Transportation Bracket Removal
Be sure to remove the transportation brackets before use (installation).
Use round head screws (5 mmø x 6 mm) for installation. (a page 8)
Round Head Screw
(5 mmø x 6 mm)
Be careful not to lose these screws.
Round Head Screw
(5 mmø x 6 mm)
Transportation
Bracket
Transportation
Bracket
CQ-VD7003N
5
English
Installation
5
(continued)
Mounting the Display Unit
❏ Installation Procedures (When using Mounting Collar w)
1
Note:
¡The car model, installation conditions and combination of the units
used may impose some restrictions on opening and closing the
monitor as well as on the angle
and position to which the monitor
can be adjusted.
Insert the Mounting Collar w into the dashboard, and
bend the mounting tabs out with a screwdriver.
Fastening the Mounting Collar
How much to bend the tabs will vary depending on the
car. Bend them with a screwdriver to fasten the
Mounting Collar w securely in the dashboard.
Dashboard
IMPORTANT
When this unit is installed in dashboard, ensure that there is sufficient
air flow around the unit to prevent
damage from overheating. Do not
block any ventilation holes on the
unit.
w Mounting Collar
Tab
r Mounting Bolt
(5 mmø)
!0 Power Connector
e Mounting Spring
y Flat-Head Screw
(5 mmø x 6 mm)
2
3
4
5
6
6
CQ-VD7003N
Attach the Mounting Springs e to the unit.
Establish the rear connection of the unit.
After fixing Power Connector !0, fix the rear of the unit to
the car body by either method (a) or (b) shown at right.
Insert the unit into Mounting Collar w.
Secure the clamp plate of Mounting Collar
w to the hook of Mounting Spring e.
Clamp plate
Insert Trim Plate q.
After installation
reconnect the negative
(–) battery terminal.
English
Method for Fixing the Mounting Spring
Two holes of the mounting spring allow you to select between two mounting types as shown below.
(A) Regular installation method
6
(B) Deeper installation method
A few millimeters of
console projecting
y Flat-Head Screw
Less projecting
y Flat-Head Screw
y Flat-Head Screw
y Flat-Head Screw
Caution
¡Method (B) is not available in some types of cars.
Method for Fixing the Rear of the Unit
(a) Using the Rear Support Strap (option)
Fire wall of car
3 mmø
Rear Support Strap
(option)
(b) Using the Rubber Cushion (option)
Rear Support Bracket
(Provided on the Car)
Rubber Bushing
(option)
Tapping Screw
(option)
Hex. Nut
(option)
r Mounting Bolt
(5 mmø)
r Mounting Bolt
(5 mmø)
CQ-VD7003N
7
English
Installation
7
(continued)
❏ Installation Procedures (When not using Mounting Collar w)
Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car
manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.
Select mounting screws according to the hole positions and hole shape of the bracket.
t Round Head Screw (5 mmø x 6 mm)
2 pieces
Recycle the Round Head Screws that fixed the transportation brackets for two more
positions.
u Round Head Screw (4 mmø x 3 mm)
4 pieces
y Flat-Head Screw (5 mmø x 6 mm)
When using these
mounting holes
4 pieces
t Round Head Screw
(5 mmø x 6 mm)
Use the supplied Spacer i if mounting hole of your
car is shaped like below.
i Spacer
Mounting Hole
of a Bracket
(in section)
Bracket
Existing Bracket (R)
o Double-Faced
Adhesive Tape
t Round Head Screw
(5 mmø x 6 mm)
i Spacer
o Double-Faced Adhesive Tape
Existing Bracket (L) (Bracket originally attached to the car)
To Remove the Unit
q Push the right and left clamp plates outward, one at a time, and pull the unit toward yourself.
w After removing the right and left clamp plates, pull the unit with both hands till it comes out.
w
q
Push here to
remove the
clamp plates.
8
CQ-VD7003N
English
Connecting the Side Brake (Parking Brake) Connection Lead
8
Caution
¡For safety, be sure to ask your nearest professional installer to do this connection.
Hand brake
Foot brake
Side brake (parking brake) switch
The side brake (parking brake) switch position varies with car model.
For details on the exact location of the side brake (parking brake) switch
in your car, contact your dealer.
Brake light
Battery
+
SIDE BRAKE
Side Brake (Parking Brake) Connection
Lead (Bright green)
When the side brake (parking brake) lever is
engaged, the unit is grounded by the chassis.
q Attach a Clip Connector !1 to the end of the side
brake (parking brake) connection lead.
!1 Clip Connector
—
Car chassis
w The Clip Connector !1 is connected to the power
source side lead of the side brake (parking brake)
lever.
Comes up to this point.
Side Brake (Parking Brake) Connection Lead
(Bright green)
Power source side lead
CQ-VD7003N
9
English
Electrical Connections
9
❏ Wiring Diagram
Caution
¡Check the connectors provided on your car (see precaution below) before connecting the system.
¡This unit is designed for use in a car having a 12 V negative ground battery system.
¡To prevent damage to the unit, be sure to follow the connection diagram.
¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords).
¡Do not insert the power connector into the unit until the wiring is completed.
¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and prevent cable terminals from touching any metal parts.
¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery
may clear the memory.
¡Run the cords avoiding the spots where the temperature can be extremely high.
Precautions (ISO Connector)
¡The pin arrangement of the power connector conforms
to ISO standard.
¡The pin arrangement of ISO connectors in some cars
may differ from the ISO standard.
¡Please check that the pin arrangement of the connector in your car conforms to ISO standard.
¡For car types A and B, change the wiring of the red
and yellow leads as shown at below.
¡After connection, insulate the portions marked (C)
with insulating tape.
Note:
¡For cars other than types A and B, please consult your
local car shop.
ISO
Standard ISO
A7: IGN or ACC 12 V supply
(Red) C (Red)
A7
(Yellow) C (Yellow)
A4
A4: 12 V Batteries (Continuous supply)
A
(For rear connectors, a page 12)
ACC
BATTERY 15A
!0 Power Connector
CQ-VD7003N
(Rear)
Car Type A
A7: 12 V Batteries (Continuous supply)
(Red)
C (Yellow)
BATTERY 15A
(Yellow) C (Red)
ACC
A4: IGN or ACC 12 V supply
B
Car Type B
A7: 12 V Batteries (Continuous supply)
(Red)
C
(Red)
ACC
BATTERY 15A
(Yellow) C
A4: No connection
10
CQ-VD7003N
(Yellow)
Note:
¡To prevent from damage to the unit, be sure to follow
the wiring diagrams at right.
¡Be sure to fully plug in the connectors. Secure them
with clamps and tapes.
¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing
engineer or your dealer if other methods are required.
English
10
Side Brake (Parking Brake) Connection Lead
(Bright green)
Be sure to wire the side brake (parking brake) for safety
and preventing accidents.
Navi Mute Lead
(Orange)
To navi mute lead of car navigation system.
External Amplifier Control Power Lead
(Blue/white stripe)
To an external amplifier.
Note:
¡Use the power control lead of the TV tuner for TV
tuner connection.
¡Connect both the power control lead of the TV tuner
and the amplifier control connector of the external
amplifier when the TV tuner and external amplifier are
connected at the same time.
CQ-VD7003N
(Rear)
!0 Power Connector
To power connector of the unit.
SIDE BRAKE
NAVI MUTE
Speakers
B8 : Rear Left –
B7 : Rear Left +
B6 : Front Left –
B5 : Front Left +
AMP-CONT MAX 0.1A
Not used.
Caution
ANT-CONT MAX 0.1A
Resistor (1 kΩ)
¡Use ungrounded speakers only.
Allowable input : 50 W or more
Impedance : 4 – 8 Ω
¡Distance between speaker and amplifier: 30 cm or more
¡Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
ACC
A7 (Red)
A7 : Power Lead (IGN or ACC) (Red)
To ACC power, +12 V DC.
A5 (Blue)
A8 (Black)
(Fuse 15 A)
Noise Filter
BATTERY 15A
B4 : Front Right –
B3 : Front Right +
B2 : Rear Right –
B1 : Rear Right +
B5
B6
B7
A8 : Ground Lead (Black)
To a clean, bare metallic part of the car
chassis.
B8
A4 (Yellow)
A5 : Motor Antenna Relay Control Lead
B8 (Green/black stripe)
(Blue)
B6 (White/black stripe)
B7 (Green)
B4 (Gray/black stripe)
B5 (White)
B2 (Violet/black stripe)
B3 (Gray)
B1 (Violet)
To Motor Antenna (Max. 100 mA).
This lead is not intended for use with a
switch actuated power antenna.
Note:
¡The power antenna extends automatically when the power of this unit is
turned on.
B4
B3
B2
B
A
A4 : Battery Lead (Yellow)
To the car battery, continuous +12 V DC.
B1
CQ-VD7003N
11
English
Electrical Connections
(continued)
Names and Colors of Rear Connectors
RGB Connector
To the Panasonic Car Navigation System.
11
System-up Connector
To external devices equipped with system-up connector.
CQ-VD7003N
(Rear)
!3 ISO Antenna
Adapter
(If needed)
!0 Power
Connector
(a page 11)
(R)(Red)
AV-OUT
(L)(White)
Video Output Terminal (AV-OUT)
Connect the rear monitor. (a page 18)
(Yellow)
PRE-OUT FRONT
PRE-OUT CENTER
PRE-OUT REAR
S.W-OUT
(R)(Red)
(L)(White)
Pre-Out Connector (front)
To external amplifier.
(Black)
Pre-Out Connector (centre)
To external amplifier.
(R)(Red)
Pre-Out Connector (rear)
To external amplifier.
(L)(White)
(Black)
Pre-Out Subwoofer connector (mono)
To external amplifier.
(R)(Red)
AV1-IN
AV2-IN
Video Input Terminal (AV1-IN/AV2-IN)
Connect a VCR, camcorder, other brand’s car
navigation system, etc. (a page 18)
(Yellow)
Note: When an external device is connected
(R)(Red)
to the system-up connector, the audio termi(L)(White) nals, {(R)(Red), (L)(White)}, of AV2-IN are
disabled.
(Yellow)
(L)(White)
REMOTE-IN
(Brown/black stripe)
CAMERA-IN
REVERSE
(Violet/white stripe)
12
CQ-VD7003N
(Yellow)
Remote-In Lead
To Remote-Out of connected device.
Camera Input Terminal (CAMERA-IN)
Connect a rear view camera (a page 17) .
Reverse Lead
When connecting the rear view camera, use
the reverse lead.
English
Connection with TV Tuner (CY-TUP153N)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
External Amplifier Control Power Lead
Note:
¡Connect both the power control lead of the TV tuner and the amplifier control connector of the external amplifier when the TV tuner and external amplifier are connected at the same time.
12
Clip connector
(option)
Power Control Lead
PWR-CONT
!0 Power
Connector
AMP-CONT MAX 0.1 A
System-up Connector
(supplied with CY-TUP153N)
Power Connector
(supplied with CY-TUP153N)
AV2-IN
CQ-VD7003N
(Rear)
(not used)
(Video)
(Yellow)
(Video)
(Yellow)
RCA Cord
(supplied with CY-TUP153N)
TV Tuner
CY-TUP153N (option)
CQ-VD7003N
13
English
Electrical Connections
(continued)
Connection with DVD Changer (CX-DH801N)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
13
DVD Changer
CX-DH801N (option)
Ground Lead (Black)
To a clean, bare metallic part of the car chassis
Power Connector
(Supplied with CX-DH801N)
BATTERY 5 A
Battery Lead
(Yellow) To the car battery, continuous +12 V DC
Power Lead (Red) (not used)
DIN Cord (Black)
ACC
DIN Connector
(R) (Red)
CHANGER IN
(L) (White)
RCA Cord
System-up
connector
Conversion Cable for DVD/CD Changer
(CA-CC30N, option)
CQ-VD7003N
(Rear)
(not used)
AV2-IN
(Video)
(Yellow)
14
CQ-VD7003N
(Video)
(Yellow)
English
Connection with CD Changer (CX-DP880N)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
14
CD Changer
CX-DP880N (option)
Ground Lead (Black)
To a clean, bare metallic part of the car
chassis
Battery Lead (Yellow)
To the car battery, continuous
+12 V DC
Power Connector
(Supplied with CX-DP880N)
DIN Cord (Black)
(R) (Red)
RCA Cord
(L) (White)
CHANGER IN
DIN Connector
System-up
connector
Conversion Cable for DVD/CD
Changer (CA-CC30N, option)
CQ-VD7003N
(Rear)
CQ-VD7003N
15
English
Electrical Connections
(continued)
Connection with Expansion Module (CY-EM100N)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
15
Head unit/Expansion Module
Connecting cable
(Supplied with CY-EM100N)
(Video) (Yellow)
(L) (White)
System-up
Connector
(R)
(Red)
(R) (Red)
VIDEO OUT
AUDIO OUT
Camcorder
(option)
(L) (White)
(Video) (Yellow)
Expansion Module
AV2-IN
CY-EM100N (option)
DVD Changer
CX-DH801N (option)
(Video)
(Yellow)
VIDEO OUT
(Video)
(Yellow)
(L) (White)
CHANGER IN
16
CQ-VD7003N
RCA cord
(option)
iPod
VIDEO-CNT
(R) (Red)
CQ-VD7003N
(Rear)
Conversion Cable
for DVD/CD
Changer (CACC30N, option)
Direct Cable for iPod
(CA-DC300N, option)
English
Connection with Rear View Camera
Note:
¡Refer to the operating instructions for the connected devices, in addition.
Rear View Camera
Control Unit (option)
CQ-VD7003N
(Rear)
16
Camera Input
(Video)
(Yellow)
Rear View Camera (option)
Panaso nic
RCA Cord (option)
CAMERA-IN
Camera Input Terminal
(Yellow)
(Video)
(Yellow)
Reverse lamp
Clip connector
(option)
Battery
Car chassis
REVERSE
Reverse Lead
(Violet/white stripe)
P
!2 Reverse Extension Cord
(Violet/white stripe)
R
N
D
2
L
Transmission gear
Connecting the Reverse Lead
If using an optional rear view camera, the reverse lead
must be connected.
Connect the reverse lead (violet/white stripe) to the positive (+) lead of the reverse lamp (the lamp with a clear
lens that lights when the transmission gear is shifted into
the reverse position).
Note:
¡Connect the reverse lead after cutting the terminal at
the end.
¡Use a Reverse Extension Cord !2 if needed.
Check the reverse lamp.
Take it out of the back of
the tail lamp mount.
CQ-VD7003N
17
English
Electrical Connections
17
(continued)
Connection with Rear Monitor
Note:
¡Refer to the operating instructions for the connected devices, in addition.
¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in
order to establish a proper connection.
STAND BY (R)
ON (G)
Caution
COLOR LCD MONITOR
¡For people sitting in the front seats, please
enjoy only audio during driving.
Rear Monitor
Panasonic
VM1500
Audio Right
Audio Left
Video Input
Example:
(R) (Red)
(Video) (Yellow)
(L) (White)
CQ-VD7003N
(Rear)
(Video) (Yellow)
AV-OUT
RCA Cord
(option)
(R) (Red)
(L) (White)
Connection with VCR or Camcorder
Note:
¡Refer to the operating instructions for the connected devices, in addition.
¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in
order to establish a proper connection.
CQ-VD7003N
(Rear)
(Video) (Yellow)
RCA Cord
(option)
AV1-IN
(R) (Red)
(L)
(White)
(L) (White)
(R)
(Red)
(Video)
(Yellow)
INTELLIGENT SYSTEM
POWER
BS G-CODE
Camcorder (option)
18
CQ-VD7003N
VCR (option)
Example:
Video Output
Audio Left
Audio Right
Note:
¡Refer to the operating instructions for the connected devices, in addition.
English
Connection with Car Navigation System (CN-DV2300N)
18
Car Navigation System
CN-DV2300N (option)
Power Connector
(Supplied with CN-DV2300N)
RGB Cord
(Supplied with CN-DV2300N)
CQ-VD7003N
(Rear)
RGB Connector
!0 Power Connector
Clip connector
(option)
NAVI MUTE
NAVI MUTE
Navi Mute Lead
(Orange)
Navi Mute Lead
(Orange)
CQ-VD7003N
19