Panasonic CYVMD9000U Operating instructions

Panasonic CYVMD9000U Operating instructions
General
E
N
G
L
I
S
H
1
9
2
Power
Monitor Position Adjustment
10
Turn the key in the ignition until the accessory
indicator lights.
ON: Press [MODE] (POWER) on the display
unit.
Press [PWR] or [MODE] on the remote
control.
OFF: Press and hold [MODE] (POWER) again
for more than 2 seconds on the main
unit.
Press and hold [PWR] again or [MODE]
again for more than 2 seconds on the
remote control.
Cautions:
≥ For smooth adjustment, make sure to first return the lateral angle to the neutral position and then adjust
the tilt angle.
≥ Do not manually change the position of the unit by using force.
≥ Do not place any object on the display unit, or subject it to undue force.
ACC
ON
[ ] (OPEN/CLOSE)
Tilt Angle/Front-Rear Position
NAVI
CT
ASPE
ASPDE
P•MO
[PWR]
DVD (Video CD/CD) player (
page 26)
["] [#]
[%] [$]
(MONITOR
POSITION
ADJUSTMENT)
Monitor position setting menu
2
[MODE]
["] [#]
VOL
[MUTE]
E
P• MOD
Volume
Display Open/Close
["] (VOLUME): Up
[#] (VOLUME): Down Setting range: 0 to 40
OPEN: Press [ ] (OPEN/CLOSE).
When using CY-VMD9000U itself:
Supplied speaker volume
When connecting to CA-TU7000U:
External speaker volume connected to this unit
Note:
≥ The sound level for each source is stored
in memory.
R
POWE
MUTE
[MUTE]
[#] ["] (VOLUME)
page 38)
*
(
page 34)
Radio
*
(
page 32)
CD changer control
(When a CD changer is connected.)
*When connecting to CA-TU7000U/9000U.
If the unit stops halfway, press
[ ] (OPEN/CLOSE) again and
draw it all the way in.
CLOSE: Press [ ] (OPEN/CLOSE) again.
(After return the lateral angle to the neutral
position.)
Notes:
≥ When the display unit is opened or closed, a loud beep
sounds three times.
≥ Opening/closing the display can be operated when the
power is turned off.
CY-VMD9000U
Tilt angle
1 to 5
["]
[#]
Press ["] or [#] to adjust the tilt angle.
Press [%] or [$] to move the display to
the front or rear position.
Front-rear position
Rear
[$]
Front
[%]
≥ Position “REAR” and the tilt angle “5”
cannot be selected at the same time.
Notes:
≥ Press [MODE] to return to the regular mode.
≥ The monitor position setting menu is automatically closed if no operation is performed for about 60 seconds.
≥ Vertical angle (TILT) and front-rear position data are saved in the memory, so when the display unit is drawn
out next, it is automatically set at the angle and in the position adjusted before.
≥ After adjusting its angle, also adjust the brightness to make it easy for you to watch. (➡ page 54)
≥ The monitor position can also be set on the main menu screen. (➡ page 44)
≥ The car model and installation conditions may impose some restrictions on the adjustment of the monitor’s
angle and position.
Display Unit Lateral Angle Adjustment
View from above
WARNING:
Do not insert hands, fingers or foreign objects into the unit while the display is moving.
Inserting your hands, fingers or foreign objects into the unit can cause injuries and damage to the unit.
24
Press and hold [TILT] on the display unit
for more than 1 second.
E
MOD
U
MEN
ME
VOLU
(
MUTE ON: Press [MUTE].
MUTE OFF: Press [MUTE] again.
OPEN
ENTER
ION
AT
NAVIG
Press [MODE] to change the mode.
Source
(
page 38)
VTR 1
Mute
1
E
/CLOS
TILT
Mode
VTR 2
E
N
G
L
I
S
H
TILT
Hold the display unit by the non-slip part in the upper half of
it, and adjust its lateral angle.
Caution:
≥ There is the danger of your fingers being pinched if
you hold the unit by lower part. Hold the unit by the
upper half of it, and move it carefully without applying undue force.
Folding down the Display Temporarily
Fold down: Press [TILT] on the display unit.
Raise: Press [TILT] again on the display unit.
Note:
≥ Even when the unit is power off, you can fold down the display temporarily.
CY-VMD9000U
25
Basic Disc Operations
E
N
G
L
I
S
H
Meaning of symbols
11
DVD
VIDEO
VIDEO
CD
CD
Indicates the compatible types of disc.
Cautions:
≥ Do not use irregularly shaped disc.
≥ Do not insert foreign matter into the disc slots.
Perform these operations with the remote control.
Operations vary according to the disc.
For details, refer to the guide provided with the disc.
Mode display
Play setting
Playing time
Disc format
(➡ page 23)
Title/chapter number
Subtitle language/audio language/angle
Input is not possible when the operation is
not supported by the disc.
Insert a disc after making sure that there is no disc in the disc compartment.
(If “NO DISC” is displayed, insert the disc.)
Video CD mode display
Disc Insert and Playback
Mode display
Insert the disc.
Play setting
[%] [$]
[#] ["]
[ENTER]
ENTER
TION
NAVIGA
NAVI
ASPECT
ASP
[<] (EJECT)
MODE
ER
MENU
ME
VOLU
POW
MUTE
Sound setting
(Stereo/monaural)
Track number
Playing time
[MODE]
To make sure the play setting
Selecting a Menu Item
Press [ENTER] during the playback.
Notes:
≥ Loading a disc when the power is off allows the power to
be turned on.
≥ You can play a disc even if the monitor is closed.
≥ If you leave a disc at the disc slot for approximately
30 seconds, the disc is loaded into the compartment
automatically after loud beep is energized three times.
≥ The sound may be interrupted for a few moments while
the disc is being identified.
Mode Selection
Press [MODE] to change to the DVD (Video CD, CD) mode.
12
DVD mode display
Notes:
≥ Disc Limitations
Due to limitations of certain discs, some DVD video and video CD discs may not operate as described in
these Operating Instructions. Refer to the disc jacket for further details.
≥ This unit does not support DVD and video CD karaoke functions.
≥ The mode that supports that disc is selected, and playback starts.
≥ The disc format is automatically identified. (➡ page 23)
≥ When the menu screen appears, see “Selecting a Menu
Item” on page 27.
E
N
G
L
I
S
H
Only for the remote control
Label side
[MODE]
[DVD] (DVD MENU)
[RET] (RETURN)
[%] [$] ["] [#]
[ENTER]
[:]
[9]
[0] to [9]
(SELECT MENU)
E
P• MOD
DVD
VIDEO
VIDEO
CD
Some DVD discs have unique menu structures called DVD menu.
Although the DVD menu’s contents and operation differ from disc to
disc, the following explains basic operation when this feature is used.
1
2
DVD:
Press [%], [$], [#] or ["] to select the desired menu.
DVD/video CD with playback control (➡ page 89):
Press [0] to [9] on the remote control.
Press [ENTER].
To display the menu:
DVD: Press [DVD] (DVD MENU) during playback.
Video CD: Press [RET] (RETURN) during playback.
Example:
DVD MENU
1. SUBTITLE
2. AUDIO
3. ANGLE
Example:
Video CD
Select your favorite music.
Stop and Disc Eject
Press [<] (EJECT) on the display unit.
26
CY-VMD9000U
To input the number again or return to the previous display:
Press [RET] (RETURN).
Note for video CD with playback control:
≥ Pressing [:] [9] during playback will return to the menu display.
1. Love Supremes
2. Impressions
3. In a Sentimental Mood
Number:
CY-VMD9000U
27
Basic Disc Operations (Continued)
E
N
G
L
I
S
H
[∫] (STOP)
[[ [] (PAUSE)
[1] (PLAY)
[:] [9]
[%] [$] ["] [#]
[ENTER]
[REP] (REPEAT)
Listening to DVD/Video CD
13
Go to Beginning
Fast Forward/
Fast Backward
[9]: Next track (chapter)
[:]: Beginning of the current track (chapter)
Previous track (Press twice.)
Note:
≥ When playing a DVD video, there are cases where it is not possible
to return to the start of a chapter that spans 2 titles.
≥ When play is stopped, the player records the point where [∫]
(STOP) was pressed. (Continued playback function)
Press [1] (PLAY) again, and play will resume from this point.
Stop
[0] to [9]
(TITLE/CHAPTER NUMBER)
Press and hold for more than 0.5 seconds.
[9]: Fast forward
[:]: Fast backward
Release to resume the regular play on the regular speed.
≥ The speed changes if the button is held down as follows.
Regular speed > 1.5 times > 10 times > 20 times
Press [∫] (STOP) during playback.
To cancel continued playback:
Press [∫] (STOP) again in the stop mode.
Starting Playback
from a Specific
Title/Chapter
DVD
VIDEO
To resume normal playback:
Press [1] (PLAY) or [[ [ ] (PAUSE) again.
Slow Playback
Chapter/
Track
Press and hold [9] for more than 0.5 seconds in the pause mode.
≥ Playback is at about 1/3 normal speed.
To resume normal playback:
Press [1] (PLAY).
To pause:
Press [[ [ ] (PAUSE) again.
Note:
≥ Reverse slow playback is not possible.
Press [REP] (REPEAT) during playback.
Press [REP] (REPEAT) again to cancel.
Repeat
Title
Press and hold [REP] (REPEAT) for more than
2 seconds during playback.
Press and hold [REP] (REPEAT) for more than
2 seconds again to cancel.
Note:
≥ It is possible to press [%] [$] on the display unit instead of [:] [9] on the remote control except the
DVD’s menu play.
28
CY-VMD9000U
DVD Menu
Use this menu during
playback to select content,
audio, subtitle, etc., from a
menu (the DVD menu)
that is unique to each disc.
DVD
VIDEO
Title Menu
If the DVD has multiple
titles recorded on it, it is
possible to select the preferred title form the title
menu to start playback.
DVD
VIDEO
14
[DVD] (DVD MENU)
[RET] (RETURN)
[TITLE]
(TITLE/CHAPTER)
E
P• MOD
1 Press [TITLE] (TITLE/CHAPTER) to select the input mode.
Input
preferred title/chapter
2
number.
Press [[ [ ] (PAUSE) during playback.
Pause
E
N
G
L
I
S
H
Only for the remote control
Regular mode
Chapter number input mode
(“CHAP” lights on yellow.)
To input the number again:
Press [RET] (RETURN).
Title number input mode
(“TITLE” lights on yellow.)
3 Press [TITLE] (TITLE/CHAPTER).
≥ Playback will start automatically.
Notes:
≥ If no operation is performed, the display returns to the regular
mode.
≥ You can select the desired setting on the menu display. (➡ See
below.)
1 Press [DVD] (DVD MENU) during
playback.
Example:
2 Press [%], [$], [#] or ["] to select
the preferred menu.
3 Press [ENTER].
DVD MENU
1. SUBTITLE
2. AUDIO
3. ANGLE
To return the previous display:
Press [RET] (RETURN).
Note:
≥ Operations vary according to the disc. For details, refer to the guide
provided with the disc.
1 Press and hold [DVD] (DVD MENU)
for more than 2 seconds during playback.
Press
[%], [$], [#] or ["] to select
2
the preferred title.
3 Press [ENTER].
Example:
TITLE MENU
Rivers
Castles
Lovers
Woods
To return the previous display:
Press [RET] (RETURN).
Note:
≥ Operations vary according to the disc. For details, refer to the guide
provided with the disc.
CY-VMD9000U
29
Basic Disc Operations (Continued)
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Only for the remote control
CD mode display
Track number
Mode display
15
16
Play setting
Playing time
Number of track
[SUB] (SUB TITLE)
[ANGLE]
[%] [$]
[REP] (REPEAT)
[AUDIO]
[0] (ST/MONO)
Switching the
Subtitle Language
DVD
VIDEO
E
P• MOD
“OVER 1” shows when the number
of tracks is 21 or more.
It is possible to change the subtitle language during play if the multiple languages are recorded on the disc.
Note:
≥ There may be a brief delay before the subtitles appear.
Switching the
Audio Language
DVD
VIDEO
Switching the
Angle
DVD
VIDEO
Listening to CD
Press [SUB] (SUB TITLE) during playback.
Go to Beginning
[$]: Next track
[%]: Beginning of the current track
Previous track (Press twice.)
Press [AUDIO] during playback.
It is possible to change the audio language during play if multiple
audio languages are recorded on the disc.
Fast Forward/
Fast Backward
Press and hold.
[$]: Fast forward
[%]: Fast backward
Release to resume the regular play.
Press [ANGLE] during playback.
For DVDs which contain scenes which have been shot simultaneously from a number of different angles the same scene can be viewed
each of these different angles during play.
Repeat
Press [REP] (REPEAT) during playback.
Press [REP] (REPEAT) again to cancel.
Notes:
≥ If no operation is performed for 5 seconds, the display returns to the regular mode.
≥ It may not be possible to switch language unless the unit is at the DVD menu (➡ page 29) or is at the DVD settings (➡ page 56).
≥ The language on the DVD settings has a priority over when the power is turned on or the disc is loaded.
≥ The number of languages depends on the disc. Some disc have only one language or have no language.
Switching between
Stereo and
Monaural
Press and hold [0] (ST/MONO) for more than 2 seconds.
It is possible to switch the audio between stereo sound and monaural
sound (L or R).
ST
VIDEO
CD
MONO Lch
MONO Rch
30
CY-VMD9000U
: Stereo sound
: The left channel audio is output on both the left
and right speakers.
: The right channel audio is output on both the left
and right speakers.
CY-VMD9000U
31
CD Changer Basics
E
N
G
L
I
S
H
CD changer functions are designed for optional Panasonic CD changer unit.
Preparation:
≥ Connect the CD changer, and load a magazine (disc).
Notes:
≥ Loading a magazine when the power is off allows the power to be turned on.
≥ Ejecting the magazine when the unit is in the CD changer mode allows the power to be turned off.
17
E
N
G
L
I
S
H
When connecting to CA-TU7000U/9000U
CD changer mode display
Mode display
Disc number
Number of disc in
CD changer
Caution:
≥ Do not use irregularly shaped disc.
Track number*1
*1Not shown correctly when the number of tracks is 100 or more.
Play setting
Playing time
18
Number of track
“OVER 1” shows when the number
of tracks is 21 or more.
Various Way of Listening (Only for the Remote Control)
1
CD Changer Mode
Press [MODE] to change to CD changer mode
and playback starts.
Note:
≥ Load a magazine with CDs when “NO MAGAZINE” is displayed.
Track
Press [4] (RANDOM).
All the available tracks on all discs in the magazine plays in a
random sequence.
≥ Press [4] (RANDOM) again to cancel.
Disc
Press and hold [4] (RANDOM)
for more than 2 seconds.
All the available tracks on the current disc plays in a random
sequence.
≥ Press and hold [4] (RANDOM) again to cancel.
Track
Press [5] (SCAN).
The first 10 seconds of each track on the discs plays in
sequence.
≥ Press [5] (SCAN) again to cancel.
With the scanning of all tracks over, the original program starts
playing form the beginning.
Disc
Press and hold [5] (SCAN)
for more than 2 seconds.
The first 10 seconds of the first track of all the discs in the magazine plays in sequence.
≥ Press and hold [5] (SCAN) again to cancel.
With the scanning of all tracks over, the original disc starts
playing from the beginning.
Track
Press [6] (CH REPEAT).
Repeat the current track.
≥ Press [6] (CH REPEAT) again to cancel.
Disc
Press and hold [6] (CH REPEAT)
for more than 2 seconds.
Repeat the current disc.
≥ Press and hold [6] (CH REPEAT) again to cancel.
Random Play
DISC/BAND
VOLUME
MUTE
MENU
MODE
POWER
2
3
NAVIGATION
ASPECT
NAVI
ASP
ENTER
TRACK/
TUNE
P•MODE
Disc Selection
["] (DISC): Next disc.
[#] (DISC): Previous disc.
Track Selection
[MODE]
[$] (TRACK): Next track.
[%] (TRACK): Beginning of the current track.
Previous track (Press twice.)
["] [#] (DISC)
[%] [$] (TRACK)
Track Search
Press and hold for more than 0.5 seconds.
[$] (TRACK): Fast forward
[%] (TRACK): Fast backward
Release to resume the regular play.
E
P• MOD
[4] (RANDOM)
[5] (SCAN)
[6] (CH REPEAT)
Scan Play
Repeat Play
32
CY-VMD9000U
CY-VMD9000U
33
Radio
E
N
G
L
I
S
H
Radio mode display
19
E
N
G
L
I
S
H
When connecting to CA-TU7000U/9000U
One-Touch Selection of a Station
Mode display
20
Up to 6 stations each can be saved in the FM1, FM2, AM1 and AM2 preset station memories.
Stereo indicator
Frequency
1 Select a band and frequency (step 1, 2 and 3 on the previous page).
Band
Preset memory
Manual Preset
Memory
Manually save a station in the
preset memory.
1
Radio Mode
2
Band
Press [MODE] to change to radio mode.
2 Press and hold [1] to [6] on the remote control for more than
2 seconds.
The frequency blinks once,
and a receiving station is
saved in the memory.
1 Select a band (step 1 and 2 on the previous page).
2 Press and hold [ENTER] for more than 2 seconds.
3
DISC/BAND
VOLUME
NAVIGATION
MUTE
MENU
MODE
POWER
NAVI
ASPECT
ASP
ENTER
TRACK/
TUNE
P•MODE
["] (BAND): FM band
[#] (BAND): AM band
Auto Preset Memory
Automatically save strong
stations in the preset memory.
Tuning
[$] (TUNE): UP
[%] (TUNE): Down
[MODE]
["] [#] (BAND)
[%] [$] (TUNE)
[ENTER]
Press and hold [$] (TUNE) or [%] (TUNE) for more
than 0.5 seconds, then release. Seeking will start.
Note:
≥ The stereo indicator lights during reception of an FM stereo
broadcast.
E
P• MOD
≥ The 6 strongest available stations will be automatically saved in
the memory under preset numbers 1 to 6.
≥ Once set, the preset stations are sequentially scanned for 5 seconds each.
≥ To stop scanning, press [1] to [6] on the remote control.
Note:
≥ New stations are overwritten on existing saved stations after following this procedure.
[1] to [6]
(PRESET MEMORY)
Preset Station
Calling
34
CY-VMD9000U
1 Select a band (step 1 and 2 on the previous page).
2 Press [1] to [6] on the remote control.
CY-VMD9000U
35
Useful Functions
E
N
G
L
I
S
H
21
When connecting to
CA-TU7000U/9000U
E
N
G
L
I
S
H
You can mute the sound from the rear speakers connected to the front monitor (this unit), when you have different
modes at the front and rear monitor, after connecting the
rear monitor.
22
You can enjoy the sound from the rear monitor by using
headphones.
DISC/BAND
VOLUME
NAVIGATION
MUTE
MENU
MODE
POWER
NAVI
ASPECT
ASP
ENTER
TRACK/
TUNE
P•MODE
[ASP] (P• MODE)
Private Mode
Default: OFF
Private mode ON: Press and hold [ASP] (P • MODE) for more than 2 seconds on the display unit.
Press and hold [A] (P • MODE) for more than 2 seconds on the remote control.
Private mode OFF:Press and hold [ASP] (P • MODE) again for more than 2 seconds on the display
unit.
Press and hold [A] (P • MODE) again for more than 2 seconds on the remote control.
“P • MODE” indicator lights when
the private mode is activated.
E
P• MOD
[A] (P•MODE)
36
CY-VMD9000U
Notes:
≥ Be sure to set to OFF when you do not use the private mode.
≥ It is not possible to choose and set the BAL/FAD on the sound setting menu while private mode is
activated when connecting to CA-TU7000U.
≥ It is not possible to choose and set the SP SET UP/SP DELAY on the sound setting menu while private mode is activated when connecting to CA-TU9000U.
≥ When MAIN-IN is set to ON, private mode will be inactivated.
CY-VMD9000U
37
Useful Functions (Continued)
E
N
G
L
I
S
H
Press [MODE] to change to the VTR1 or VTR2 mode.
23
VCR/Camcorder
Preparation:
≥ Connect a VCR or camcorder.
(➡ page 77)
Select the same mode (VTR1 or VTR2) as the terminal that
is connected to a VCR or camcorder (VTR1-IN or VTR2IN).
E
N
G
L
I
S
H
(Example)
00
24
VCR
Camcorder
CY-VMD9000U
Control unit
VTR1-IN VTR2-IN
DISC/BAND
VOLUME
NAVIGATION
MUTE
MENU
MODE
ASPECT
NAVI
POWER
ENTER
ASP
[MENU] [MODE]
[%] [$]
(SELECT)
[ENTER]
TRACK/
TUNE
P•MODE
[%] [$]
(SELECT)
[ENTER]
Rear View Camera
Preparation:
≥ Connect a rear view camera and a reverse
lead. (➡ page 79)
≥ Select a terminal in the “CAMERA IN”
screen according to the terminal actually
connected to the rear view camera.
(➡ page 48)
Shift the transmission gear into the reverse position.
≥ The display shows a picture from the rear view camera.
Notes:
≥ You can see a picture from the rear view camera even if
the power of the display unit is inactivated.
≥ You can see a picture from the rear view camera if you
change the mode to the same one (VTR1 or VTR2) as
the terminal to which the rear view camera was connected (VTR1-IN or VTR2-IN).
(Example)
Rear view camera
Panas o nic
CY-VMD9000U
Control unit
VTR1-IN VTR2-IN
1 Press and hold [MENU] for more than 2 seconds.
[MODE] [MENU]
2 Press [$] or [%] to select an item.
AUTO
Rear Monitor
VTR1
VTR2
E
P• MOD
You can have different picture or sound at the
front and rear monitor at the same time.
Default: AUTO
Preparation:
≥ Connect another monitor. (➡ page 77)
38
CY-VMD9000U
DVD
: Picture and sound come out. These are in
the same mode as the front monitor (this
unit).
: Picture and sound in the VTR1 mode
always come out.
: Picture and sound in the VTR2 mode
always come out.
: Picture and sound in the DVD player mode
(disc in this unit) always come out.
≥ Only sound in the CD player mode.
Rear monitor setting menu
(Example)
Rear monitor
(CY-VM5800U)
VTR-IN
3 Press [ENTER] to set.
CY-VMD9000U
Control unit
Notes:
VIDEO-OUT
≥ Press [MODE] to return to the regular mode.
≥ The display returns to the previous one with no operation for 60 seconds after changing to the rear
monitor setting menu.
≥ Picture and sound from the car navigation system connected to an RGB input cord are not available
at the rear monitor.
≥ Radio and CD changer mode is not available at the rear monitor when connecting to CATU7000U/9000U.
≥ You can mute the sound from the rear speakers connected to the front monitor (this unit), so that
you can have different modes at the front and rear monitor. (➡ page 36)
CY-VMD9000U
39
Useful Functions (Continued)
E
N
G
L
I
S
H
When you connect a car navigation system
through RGB cord [Panasonic car navigation
(not available yet)]:
25
Car Navigation
DISC/BAND
VOLUME
NAVIGATION
MUTE
MENU
MODE
NAVI
ASPECT
ENTER
ASP
TRACK/
TUNE
P•MODE
POWER
[MODE] [NAVI] (NAVIGATION)
[NAVI] (NAVIGATION)
[MODE]
Preparation:
≥ Connect a car navigation system.
≥ Select a terminal in the “NAVI SETUP”
screen according to the terminal actually
connected to the car navigation system.
(➡ page 46)
E
N
G
L
I
S
H
(Example)
DVD video/audio RGB: car navigation
output
Car navigation ON: Press [NAVI] (NAVIGATION).
Car navigation OFF: Press [NAVI] (NAVIGATION) again.
Panasonic car
navigation system
Notes:
≥ When you connect a Panasonic car navigation system
with a built-in DVD player, use an RGB cord as well.
≥ The sound that a Panasonic car navigation system generates comes from the speakers supplied with CYVMD9000U/CY-VMC7000U.
CY-VMD9000U
Control unit
00
26
VTR1-IN VTR2-IN
CY-VMD9000U
Display unit
RGB input cord
When you connect a car navigation system to
VTR1-IN or VTR2-IN terminal (other brand’s
car navigation system):
(Example)
Car navigation ON: Press [NAVI] (NAVIGATION).
Car navigation OFF: Press [NAVI] (NAVIGATION) again.
Other brand’s car
navigation system
Or press [MODE] to change to the VTR1 or VTR2 mode.
Select the same mode (VTR1 or VTR2) as the terminal that
connected to a car navigation system (VTR1-IN or VTR2IN).
CY-VMD9000U
Control unit
VTR1-IN VTR2-IN
E
P• MOD
40
CY-VMD9000U
CY-VMD9000U
41
Useful Functions (Continued)
E
N
G
L
I
S
H
E
N
G
L
I
S
H
27
00
28
Press [ASP] (ASPECT) on the display unit or press [A] (ASPECT) on the remote control to change the
aspect ration as follows.
Normal (Default)
≥ The conventional display image has a 4 to 3
ratio of horizontal to vertical.
≥ In this case, a blank area remains on the
right and left sides of the display.
DISC/BAND
VOLUME
NAVIGATION
MUTE
MENU
MODE
ASPECT
NAVI
ASP
ENTER
TRACK/
TUNE
P•MODE
POWER
[ASP] (ASPECT)
Aspect Ratio
Default: Normal
Mode: 4 types
E
P• MOD
Full
≥ The screen is extended horizontally as a
whole to the aspect ratio of 16 to 9.
≥ The extension ratio is the same at any point
of the screen.
Zoom
≥ The screen is fully extended at the normal
aspect ratio of 4 to 3.
≥ The top and bottom of the screen are slightly cut.
Just
≥ The screen is extended horizontally to the
aspect ratio of 16 to 9.
≥ The extension ratio increases toward the
right and left ends of the screen.
[A] (ASPECT)
Notes:
≥ This adjustment is common to VTR1/VTR2 and DVD (video CD) mode.
≥ You cannot change the aspect in the menu screen and a screen in the CD mode. These are fixed to
“Full”.
≥ The “Zoom” and “Just” screens do not apply to the car navigation images.
≥ When the rear view camera is in operation with the transmission gear shift in the reverse position,
the image is shown on the “Full” screen only.
≥ In some cases, the picture looks different from the original one due to your selection of aspect.
Cautions:
≥ This is to remind you that compression or extension of the screen using the aspect ratio (screen mode)
changing function of this product for commercial purpose of profit making or viewing/listening by the
public could infringe on the rights of the author protected by the copyright law.
≥ If you expand a normal picture (4 to 3) by using “Just”, “Zoom” or “Full” aspect the full of the screen, you
might not see the periphery of the picture, or you might see deformed picture. Therefore, use the
“Normal” mode to see the original picture as the author intended it.
42
CY-VMD9000U
CY-VMD9000U
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement