Panasonic TH37PX600B Operating Instructions

Panasonic TH37PX600B Operating Instructions
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection
points, where they will be accepted on a free of charge basis. Alternatively, in some countries you
may be able to return your products to your local retailer upon the purchase of an equivalent new
product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate
waste handling. Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Operating Instructions
Plasma Television
Model No.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
TH-37PX600B
TH-42PX600B
TH-50PX600B
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method
of disposal.
Licence
Trademark
Credits
••
••
••
•
DVB is a trademark of the DVB Digital Video Broadcasting Project (1991 to 1996).
VGA is a trademark of International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, USA.
S-VGA is a registered trademark of the Video Electronics Standard Association. Even if no special notation
has been made of company or product trademarks, these trademarks have been fully respected.
SD Logo is a trademark.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
TruSurround XT, SRS and
symbol are trademarks of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
IDTV
Customer’s Record
The model number and serial number of this product may be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your
purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
U.K. Standard
English
6
Printed in Czech Republic
Please read these instructions before operating your set and retain them for future reference.
The images shown in this manual are for illustrative purposes only.
Turn your living room into a home theatre!
Contents
Experience an amazing level of multi-media excitement
Be Sure to Read
Receive terrestrial digital services using an integrated (Digital Video Broadcasting) tuner
(Display DVB programmes with TV Guide (p. 14) / Timer recording (p. 36) /
Register and instantly call up favorite programmes with Profile Edit (p. 28))
•
••
Safety Precautions ······································ 4
(Warning & Caution)
Notes ··························································· 5
Maintenance ··············································· 5
Enjoy rich multi-media
SD memory card
Camcorder
Quick Start Guide
Accessories/Options············ 6
Identifying Controls ·············· 7
Basic Connection ·················· 8
Auto Setup······························ 10
Personal
computer
Quick Start Guide
Sharp pictures with HDMI terminal
Control DVD recorder / VCR via TV with Q-Link connection (p. 42)
Create home theatre and DVD recorder link-ups with
"Control with HDMI" without complicated settings!
Enjoy your TV!
DVD recorder
VCR
Satellite receiver
DVD player
Basic Features
••
••
•
•
••
••
•••
•
••
••
FAQs, etc.
••
••
••
•
Watching TV ·············································· 12
Using TV Guide (DVB) ······························ 14
Viewing Teletext ········································ 16
Watching VCR, DVD and Satellites ·········· 19
Viewing
Amplifier with
Speaker system
Advanced Features
2
FAQs, etc.
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
TH-37PX600B Declaration of Conformity No 3982, 19th January 2006
TH-42PX600B Declaration of Conformity No 3981, 19th January 2006
TH-50PX600B Declaration of Conformity No 3980, 19th January 2006
Technical Information ································ 48
FAQs ························································· 51
On screen messages ································ 53
On screen messages (SD Card) ··············· 54
Index ························································· 55
Specifications ············································ 55
Licence ······················································ 56
Advanced
How to Use Menu Functions ····················· 20
(picture, sound quality, etc.)
DVB Settings (DVB) ·································· 26
(pay-TV, subtitles, etc.)
Profile Edit / Child Lock (DVB) ·················· 28
DVB Tuning Menu (DVB) ·························· 30
Displaying PC Screen on TV····················· 31
Editing and Setting Channels (Analogue) ···· 32
Restore Settings ······································· 34
Owner ID ··················································· 35
Recording Controls ··································· 36
Viewing from card
(MPEG4 Videos and photos) ····················· 38
Recording to card ······································ 40
Q-Link Functions ······································· 42
HDMI Functions ········································ 43
External Equipment ··································· 46
3
Safety Precautions
Notes
Warning & Caution
Handling the mains plug
Power source
Ensure that the mains plug is easily accessible at all
times. The On/Off switch on this model does not fully
disconnect the TV from the mains supply. Remove the
mains plug from the wall socket when the TV set is not
used for a prolonged period of time.
Ensure the grounding pin on the mains plug is securely
connected to prevent electrical shock.
An apparatus with CLASS I construction shall be connected
to a mains socket outlet with a protective earthing connection.
This TV set is designed to operate on 220-240V,
50 / 60 Hz AC.
Note
If the set is not switched off when the TV station stops
transmitting, it will automatically go to standby mode after 30
minutes. This function will operate only in Analogue TV mode.
Do not expose to
direct sunlight and
other sources of heat
AC 220-240 V
50 / 60 Hz
Avoid exposing the TV set to direct
sunlight and other sources of heat. To
prevent fire never place any type of
candle or naked flame on top or near
the TV set.
IMPORTANT: THE MOULDED MAINS PLUG
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is
fitted in this mains plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating
of 5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark ASA or the BSI mark
on the body of the fuse.
If the mains plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the mains plug must not be used until a replacement cover is obtained.
A replacement fuse cover may be purchased from your local Panasonic Dealer.
If the fitted moulded mains plug is unsuitable for the socket outlet in your home, then the fuse shall be
removed and the mains plug cut off and disposed of safety. There is a danger of severe electrical shock
if the cut off mains plug is inserted into any 13 amp socket.
If a new mains plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: – THIS APPARATUS MUST BE EARTHED.
IMPORTANT: – The wires in this mains lead are coloured in accordance with the following code: –
Green-and-Yellow: Earth Blue: Neutral Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your mains plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the mains plug which is
marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the mains plug
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the mains plug
which is marked with the letter L or coloured RED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and replace the fuse.
4
Do not display a still picture for a long time
Do not remove the cover
Do not remove the rear cover as live parts are
accessible when it is removed. There are no
user serviceable parts inside.
Do not expose to rain or
excessive moisture
To prevent damage which might result in electric
shock or fire, do not expose this TV set to rain
or excessive moisture.
This TV must not be exposed to dripping or
splashing water and objects filled with liquid,
such as vases, must not be placed on top of or
above the TV.
Do not block the rear
ventilation openings
This causes the image to remain on the plasma
screen ("after-image").
This is not considered a malfunction and is
not covered by the warranty.
Typical still images
Channel number and other logos
Image displayed in 4:3 mode
Video game
Computer image
12
4:3
To prevent after-image, the screen saver is
automatically activated after a few minutes if no signals
are sent or no operations are performed. (p. 51)
Keep the unit away from these equipment
Electronic equipment
In particular, do not place video equipment near the unit
(electromagnetic interference may distort images / sound).
Equipment with an infrared sensor
This TV also emits infrared rays (this may affect
operation of other equipment).
Ventilation should not be impeded by covering
the ventilation openings with items such as
newspapers, tablecloths and curtains.
Maintenance
Allow sufficient space around
the unit for radiated heat
First, remove the mains plug from the socket outlet.
10
10
10
7
6
(cm)
Do not place the TV on
sloped or unstable surfaces
The TV may fall off or tip over.
Use only the dedicated
stands / mounting equipment
Using an unauthorized stand or other fixtures may
make the unit shaky, risking injury. Be sure to ask
your local Panasonic dealer to perform setup.
Use optional stands / mounts (p. 6).
Cabinet and display panel care
Remove the mains plug from the wall socket.
The cabinet and display panel can be cleaned
with a soft cloth moistened with mild detergent
and water. Do not use solutions containing
benzol or petroleum.
TV sets can produce static electricity, care must
be taken whenever touching the TV screen.
Display panel
Daily care: Gently wipe the surface clean of dirt by using a soft cloth.
Major contamination: Wipe the surface clean using a soft
cloth dampened with clean water or water containing a
small amount of neutral detergent. Then, using a soft dry
cloth, evenly wipe the surface clean until it is dry.
Caution
•
•
The surface of the display panel has been specially
treated and may be easily damaged.
Do not tap or scratch the surface with your fingernail or
other hard object.
Use care not to subject the surface to insect repellent,
solvent, thinner, or other volatile substances
(this may degrade surface quality).
Cabinet
Daily care: Wipe the surface clean using a soft dry cloth.
Major contamination: Dampen a soft cloth with clean water
or water containing a small amount of neutral detergent.
Then, wring the cloth and wipe the surface clean with it.
Finally, wipe the surface clean with a dry cloth.
Caution
•
•
•
Use care not to subject the TV unit's surfaces to detergent.
(A liquid inside the TV unit could lead to product failure.)
Use care not to subject surfaces to insect repellent,
solvent, thinner, or other volatile substances
(this may deteriorate the surface by peeling the paint).
Do not allow the cabinet to make contact with a rubber
or PVC substance for a long time.
Mains plug
Wipe the mains plug with a dry cloth at regular intervals.
(Moisture and dust may lead to fire or electrical shock.)
5
Accessories/Options
Standard accessories
Remote Control
Transmitter
•
Clamper (2)
•
TMME258
Volume / Contrast / Brightness / Colour /
Sharpness / Tint (NTSC mode) / Bass / Treble /
Balance / Manual tuning (analogue mode) (p. 32)
AV4
S-V
Ferrite core
•
•
SD CARD slot (p. 38)
1 Year Guarantee Registration
CRM
(Customer Relationship Management)
K2CT3DH00018
Function
select
J0KF00000018
MAINS Power
On / Off switch
V
L
R
TV/AV switch
AV4 terminals
(p. 46)
Headphones jack (p. 46)
Increases or decreases the programme position by one. When
Lift door to open
a function is already displayed, press to increase or decrease
Remote control signal receiver the selected function. When in Standby mode, switches TV On.
C.A.T.S. (Contrast Automatic Tracking System) sensor
(senses brightness to adjust picture quality in "Auto" viewing mode) (p. 23)
Power LED
Installing remote's batteries
Attaching the cable clampers
Pull
open
1
•
Red light indicates Standby
mode. When using the remote
control, indicates the TV has
received a command.
DVB LED
•
Active for Timer Programming or
Standby for Direct TV Recording :orange (flash)
Timer Programming On
:orange
Switches Timer recording On/Off (p. 36)
Standby On / Off switch
(Switches TV On or Off standby)
SD Recording (p. 40)
Hook
2
Rear of the TV
Snap open
Note the correct
polarity (+ or -)
•
Remove from the TV unit
Push both side
hooks and pull
out
Snap shut
Caution
•
TH-37PX600B has
horizontal direction.
Close
Incorrect installation may cause battery
leakage and corrosion, resulting in
damage to the remote control unit.
Do not mix old and new batteries.
Do not mix different battery types (such
as alkaline and manganese batteries).
Do not use rechargeable (Ni-Cd)
batteries.
Do not burn or breakup batteries.
•
••
TY-ST42P600W
(TH-37PX600B,
TH-42PX600B)
TY-ST50P600W
(TH-50PX600B)
Sound mute On / Off
TV Guide (p. 14)
(p. 19)
OK button to confirm selections and
choices.
Press after selecting programme
positions 1 - 99 (0 - 9 in Analogue mode)
to avoid delay.
MENU
Press to access the Picture, Sound and
Setup menus (p. 22 and p. 24)
Teletext (p. 16)
Do not bundle the RF cable and mains lead together (could cause
distorted image).
Fix cables with clampers as necessary.
When using the optional accessory, follow the option’s assembly
manual to fix cables.
Optional accessories
Pedestal
Switches DVB (digital broadcasting) /
Analogue mode (p. 12)
Plasma TV stand
TY-S37PX600W
(TH-37PX600B)
TY-S42PX600W
Wall-hanging
bracket
(vertical)
TY-WK42PV3W
(TH-50PX600B)
(angle)
EXIT (Returns to TV screen)
Coloured buttons used for the
selection, navigation and operation of
various functions.
Still Picture (p. 13)
Teletext Index (p. 18)
Programme / channel change buttons (0-9)
and Teletext page buttons. (p. 12 and p. 16)
When in Standby mode, switches TV On.
Programme Information (p. 13)
Direct channel access
Use together with numeric buttons to
access analogue TV channels by entering
UHF broadcast channel number. (p. 12)
Volume
Selects programmes in sequence
VCR / DVD operations (p. 19)
Normalises (p. 22)
(Resets all settings to their default levels)
TY-WK42PR3W
DIRECT TV Recording
MULTI WINDOW (p. 13)
6
Cursor buttons to make selections and
adjustments
Subtitles (p. 13) (To view subtitles)
(TH-42PX600B)
TY-S50PX600W
Switch between viewing TV or AV input.
Identifying Controls
Accessories/Options
SD menu (p. 38 and p. 40)
••
Changes picture aspect ratio (p. 13)
Quick Start Guide
•
R6 (UM3)
Mains Lead
IDTV
STR (Normalisation store)
(Stores tuning and other
function settings)
Check that you have the accessories and items shown
Batteries for the Remote
Operating Instructions
Control Transmitter (2)
Pan European Guarantee Card
•
N2QAKB000059
Identifying Controls
To immediately record programme in VCR /
DVD recorder with Q-Link connection
(p. 42)
7
Basic Connection
External equipment and cables shown are not supplied with this TV.
Please ensure that the TV is disconnected from the mains socket before attaching or disconnecting any leads.
1
Ex.
2
Connecting aerial
(TV only)
Ex.
Connecting DVD Recorder (VCR)
(TV, DVD Recorder and VCR)
Aerial
3
Ex.
Connecting DVD Recorder (VCR) and Satellite receiver
(TV, DVD Recorder, VCR and satellite)
Aerial
Aerial
Rear of the TV
Rear of the TV
Mains lead (supplied)
Mains lead (supplied)
AV1
AV2
AV3
(Q-Link)
(Q-Link)
AV1
AV2
AV3
(Q-Link)
(Q-Link)
AC 220-240 V
50 / 60 Hz
COMPONENT
COMPONENT
AV2
AV3
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
RGB
VIDEO
S-VIDEO
VIDEO
S-VIDEO
To unfasten
Basic Connection
•
(Q-Link) (Q-Link)
•
AV1
COMPONENT
RGB
VIDEO
RF cable
Clamper
RF
cable
Quick Start Guide
Rear of the TV
RGB
VIDEO
S-VIDEO
Mains lead (supplied)
RF cable
SCART cable
(fully wired)
RF OUT
DVD Recorder or VCR
RF IN
SCART cable
(fully wired)
DVD Recorder
or VCR
RF cable
RF cable
RF OUT
RF IN
••
•
8
RF cable
SCART cable
(fully wired)
SCART cable
(fully wired)
Note
Connect to AV3 for a DVD Recorder / VCR supporting Q-Link (p. 42).
Connect to AV1 for a Satellite receiver.
If connecting the TV and Satellite receiver with SCART cable, you can watch satellite broadcast by RGB input signal.
SCART:
21 pin connection used for video, audio and switching signals (Also known as Euro SCART and Peritel)
RF:
Radio Frequency - Signal received from terrestrial aerial.
RGB / S-Video / Video:
Choose between these three video formats depending on personal preference and equipment requirement.
(RGB - Red, Green and Blue)
VCR:
Video Cassette Recorder
RF OUT
RF IN
RF cable
RF IN
Satellite receiver
9
Auto Setup
Search and store TV channels automatically.
These steps are not necessary if the setup has been completed your local dealer.
1
Plug the TV into mains socket and switch On
■ How to use remote control
(Takes a few seconds to be displayed)
•
DVB Auto Setup
Please Wait !
21
Prog. Channel Service Name
68
NetID.
TS ID. Quality
30 BBC NEWS 24
12302
4158
9
5
30 BBCI
12302
4158
9
6
30 CBBC Channel
12302
4158
9
7
30 BBC Radio Wales
12302
4158
9
8
30 BBC Radio Cymru
12302
4158
9
•
•
Exit
DOWNLOAD IN PROGRESS
PLEASE WAIT
•
Programme : 63
Remote control unavailable
Owner ID
PIN NUMBER
NAME
HOUSE NO
POSTCODE
:
:
:
:
∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
0123456789
Change character
Select character
Store Owner ID
Exit
Usable characters and numbers
Auto Setup will start to search for
TV channels and store them.
The sorted programme order
depends upon the TV signal,
the broadcasting system and
reception conditions.
If a compatible recording equipment
with Q-Link or similar technologies
(p. 42) is connected, analogue
channel information is automatically
downloaded to the equipment.
Following the on-screen operation
guide, enter your own choice of PIN
number, name, etc.
For detailed procedures
"Owner ID" (p. 35)
Make a note of the PIN number
in case you forget it.
•
•
■ When inputting owner ID later
•
used to move the cursor and select menus
used to access menus, adjust levels or to select from a range of options
used to store settings after adjustments have been made or options have been set
Using the
On Screen
Displays
used to exit the menu system and return to the normal viewing screen
■ ON SCREEN HELP Instructions box
(example: Owner ID)
Yo u n o w h a v e t h e o p p o r t u n i t y
to enter your details and
help the police crack crime
see instruction book
Owner ID
PIN NUMBER
NAME
HOUSE NO
POSTCODE
:
:
:
:
∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
0123456789
Change character
Select character
Store Owner ID
Exit
Auto Setup
Yo u n o w h a v e t h e o p p o r t u n i t y
to enter your details and
help the police crack crime
see instruction book
used to open the main menus and to return to the previous menu
•
■ When inputting owner ID
You can now use the remote
control to turn On the unit or turn
the unit to standby mode.
(Power LED: On)
Quick Start Guide
4
This will take about 3 mins.
2
Many features available on this TV can be accessed via the On Screen Display
menu.
On-screen operation
guide will help you.
If you input the ID later
"Owner ID" (p. 35)
Auto Setup is now complete and your TV is ready for viewing.
•
•
IDTV
10
•
•
To check programme list
at-a-glance
TV Guide (DVB) (p. 14)
Programme Guide (Analogue)
(p. 15)
To edit analogue channels
"Programme edit" (p. 33)
Note
If tuning and downloading data have failed, perform "Auto Setup"
(p. 33).
If you turned the TV Off during Standby mode last time, the TV will
be in Standby mode when you turn the TV On with MAINS power
On / Off switch.
11
Watching TV
1
2
■ Other useful functions (Operate after
Turn power on
(Press for about 1 second)
MAINS power On / Off switch should be On.
Picture will appear.
Select DVB (Digital Video Broadcasting) or
Analogue
)
Hold
Freeze / unfreeze picture
Display
subtitles
Display / hide subtitles (if available)
•
To change the language for DVB
"Preferred subtitles" (p. 27) (If available)
Display programme information
■ In DVB:
DVB
Programme
Channel
1 BBC ONE WALES
1 BBC ONE WALES
Corontation Street
20:00~20:55
Now
Encrypted
Multi-Audio
Corontation Street
20:00~20:55
Now
Encrypted
Multi-Audio
20:30
Profile 1
Change Category
For info press
Subtitle
TXT
Information banner
Analogue
Display
information
banner
1 BBC 1
During scrambled
broadcasting
up
Information of another channel
To set display timeout (p. 27)
Information on next programme
To watch the programme listed in the banner
To hide
Change
aspect
ratio
Change the aspect ratio (p. 48)
•
•
14 : 9
In Analogue
Each press changes the mode.
Auto aspect / 16:9 / 14:9 / 4:3 / Zoom1 / Zoom2 / Zoom3
To change the mode with colour buttons
While the bar is displayed
red green
To select a channel using programme guide (p. 15)
To select a channel inputting the channel number, e.g. 39.
→
→
1
CH_ _
View in multi window (p. 50)
2
2
AV1
Source
•
Note
To watch pay-TV (p. 27)
Watch TV,
DVD, etc.
in multi
window
red
Source
Swap
blue
•
AV1
red
red
2
AV1
Swap
AV1
2
Source
Colour bar
•
12
Source
Swap
Remote control operations
apply to the main screen.
Main
screen
Swap
Sub
screen
Watching TV
To select programmes using TV Guide (p. 14)
)
•
•
■
••
Appears also when changing channel.
Enjoy viewing the picture at its optimum size and aspect
or
■ In DVB
blue
Features
available
■ In Analogue: Displays analogue information for a few seconds.
Select a channel
down
To change the
category
Viewing
3
20:30 Profile 1
Change Category
For info press
Subtitle
TXT
Broadcast time
Extra information
(To normal banner
Volume
Category
Current time
To change the layout,
etc. first show the
colour bar
•
•
•
•
To change the layout
red green
To swap
blue
To change the source
of sub screen
yellow
To return to the
normal single-screen
view
13
Using TV Guide (DVB mode)
TV Guide―Electronic Programme Guide (EPG) provides an on-screen listing of programmes currently
broadcast and future broadcasts over the next seven days (depending on the broadcaster).
1
2
■ Other useful functions (Operate after
Select
the programme
If in Analogue mode
Select DVB
View details
of the
programme
View TV Guide (landscape or portrait)
Categor y
All Service s
Fri 6t h
TV Guide
date
DVB T V Guide
select
Details
The Bil l
2 BBC2
Hot W ar s
Holiday Progra m
Terminato r
142 ITV2
I'm A Celebrit y
New s
144 SC4
Rugb y
Page u p
Info
Categor y
Prog. typ e
Categor y
All Service s
2 BBC 2
Eastender
20:00~20:3 0
DlY SOS
20:30~21:0 0
The Bill
21:00~22:0 0
Red Cap
22:00~22:3 0
Live junction
22:30~23:0 0
23:00~23:1 0
POP 100
Cinema info
23:10~00:0 0
Sports
Change display mode
Select Programme
Select channel
Timer Programming
Exit
+24 H r
green
Category
All Services
44 Channel 4
Prog. typ e
All Type s
Page u p
Info
Page dow n
Categor y
Prog. typ e
select
category
Pay TV
To list favourite
channels (p. 29)
Profile 2
Profile 3
Prog. type
All Types
All
Types
21:00
18:00
20:00
120 Off
Ext
7/8 SA
21:30
22:30
60 Off
Ext
••
min.
Media
Edit timer
Exit
Return
Delete
0
9
EXT : External device
SD : SD Card
•
DVB LED
Orange DVB LED
(Rapid blinking during recording)
■ To return to TV Guide
•
•
•
Note
When this TV unit is turned on for the first time, or the unit is switched off for more than a week, it may take some
time before the TV Guide is completely shown.
When recording programmes, you must make the proper settings on the external recording equipment connected to the unit
or insert a Card in the unit.
If a compatible recording equipment with Q-Link or similar technologies is connected to the unit (p. 8) and the
"Q-Link" settings (p. 25) are completed, no setting of the equipment is required.
Also read the manual of the recording equipment.
In Analogue – Analogue Programme Guide (Analogue mode)
view
(Analogue mode)
If in DVB mode
Select Analogue
View a channel list
(Type list)
21:30
Movies
Red Cap
News
So
The Bill
Entertainment
blue
6/8 FR
3 ITV1
Select timer
Profile 4
programme list
of the
selected type
1 BBC1
Information
Profile 1
■ To view a
End
The Analogue Programme Guide shows channel list only. (No programme info in Analogue mode)
Radio
yellow
Start
programming event
"Timer Programming" (p. 36)
Portrait (Displays by time)
Free TV
Thu 05/08/04 18:49
Date
■ To check / change / cancel a timer
444 SC 4
(Category list)
All Services
DVB Timer Programming
Pos. Name
set
W ed 12/05/04 10:4 6
1 BBC 1
19:30~20:0 0
(Timer Programming screen)
select
type
Good bye Hell
Sport
Select the channel and watch
select
Terminator
Children’s
News
Education
The Bill
Lifestyle
The
view
Using TV Guide (DVB)
■ To next day
Timer
programming
to record
Page dow n
Turn On the DVB LED
•
red
select
The Bil l
15 To 1
W ed 12t h
■ To previous day
programme list
of the selected
category
Th e
DVB TV Guid e : Portrai t
(Landscape / Portrait)
■ To view a
Pop Ido l
Select the programme to be broadcast
and select the recording device
Viewing
■ To change the layout
watch
The Bil l
Pepsi Cha r . Good by e Hel l
Panorom a Sex And The Cit y
Landscape
(Displays by
broadcaster)
Watch the
programme
So
122 five
Change display mode
Select channel
Select Programme
Timer Programming
Exit
-24 H r
+24 H r
(TV screen)
select
Red Ca p
Emmerdal . Coronation Stree t
44 Channel4 10 O ' clock News BB C
Return to List
Select the programme now on the air
21:3 0
Eastende r DI Y SO S
21 ITV1
Channel
21:0 0
1 BBC1
To return
to the start page
Thu 05/08/04 18:4 9
View Programme
Exit
Prog. typ e
All Type s
20:00-20:3 0 DIY SOS: W e open in the Battersdy s
T ime : 19:3 0
20:0 0
20:3 0
TV Guide
time
■ To return to TV
View details
View "Portrait" to see one channel at a time
View "Landscape" to see many channels
Programme Current date and time (TV Guide start page)
DVB TV Guid e :Landscap e
Thu 05/08/04 18:5 0
IDTV
)
Analogue Programme Guide
Prog.
VCR :
1 :
2 :
3 :
4 :
5 :
6 :
7 :
8 :
9 :
10 :
11 :
12 :
Name
BBC1
BBC2
ITV
S4C
Chan.
Prog.
CH21
CH44
CH51
CH41
CH47
CH23
CH26
CH58
-
13
14
15
16
17
18
19
20
21
22
23
24
:
:
:
:
:
:
:
:
:
:
:
:
Name
Chan.
-
■ To change pages
watch
Drama
14
15
Viewing Teletext
You can enjoy news, weather forecasts and subtitles, etc. (depending on the broadcaster)
DVB (digital broadcasting) mode
Analogue mode
What is FASTEXT mode (default)?
DVB teletext services
DVB teletext services differ greatly from analogue teletext.
When you switch to a DVB teletext service, the images
you see can contain graphics and text, laid out and
controlled in a manner decided by the broadcaster.
You can check if the programme has teletext information.
•
1
If in Analogue mode
2
Switch to Teletext
What is List mode?
Information
banner (p. 13)
1 BBC ONE WALES
Displayed if
programme has
teletext information
Corontation Street
20:00~20:55
Now
Multi-Audio
20:30
Profile 1
Change Category
For info press
Subtitle
TXT
In List mode, four differently coloured page numbers are situated at the bottom of the screen. Each of these
numbers can be altered and stored in the TV’s memory. ("Store frequently viewed pages", p. 18)
■ To change mode
Select DVB
17:51 28 Feb
•
DVB teletext will not work if
subtitles are switched on.
Subtitles must be switched
off for teletext to work. (p. 13)
How to use
2
Switch to Teletext
3
Select the page
Select Analogue
•
Sub page number
<< 01 02 03 04 05 06 07
Displays the
index page
(content varies
depending on the
broadcasters)
Time / date
TELETEXT
INFORMATION
up
or
or
down
red
green yellow blue
(Corresponds to the colour bar)
As the blue bar is displayed
When "◄", "►", "▲", "▼" symbol is displayed
■ To adjust contrast
red green yellow blue
■ To return to TV
When options with numbers are displayed
When "i" is displayed
>>
17:51 28 Feb
Colour bar
When "select" or "go" is displayed
When the key words are displayed on colour bar
Current
page
number
Viewing Teletext
•
•
•
•
•
1
If in DVB mode
•
In all cases, it is possible to navigate the pages using buttons on the
remote control, but because the commands available must apply to all
manufacturers of DVB equipment, some on screen commands may
not correspond exactly to the remote control buttons.
For example:
"Teletext" in Setup menu (p. 25)
Viewing
3
In FASTEXT mode, four differently coloured subjects are situated at the bottom of the display. To access more information about one
of these subjects, press the appropriately coloured button. This facility enables fast access to information on the subjects shown.
(information)
■ To return to TV
•
■ To change the
channel
•
Note
As soon as you switch to a DVB channel with links to a teletext service,
software is downloaded in the background to enable the teletext function.
This means that when switching to a DVB channel, you should wait for
approximately 5 seconds before pressing the TEXT button - this will allow
the software to download. If you press the TEXT button before download is
complete, there will be a short delay before the text screen is displayed.
While navigating DVB teletext, you will find there is a short delay when
moving between pages while the page downloads. There is often a prompt
shown somewhere on the page (for example "Loading") to let you know that
this is happening.
■ Using Analogue teletext
Reveal
hidden
data
Reveal hidden words e.g. quiz page answers
red
•
Re-hide
red
(TOP)
FULL /
TOP /
BOTTOM
(BOTTOM)
Normal (FULL)
green
(Expand the BOTTOM half)
(Continued)
16
17
Viewing Teletext (Continued)
The Remote Control is capable of operating some functions of selected Panasonic VCRs and DVD
(Digital Versatile Disc) equipment.
Connect the Satellite receiver and you can watch satellite broadcasts.
To connect the equipment (p. 8)
Analogue mode
■ Using Analogue teletext (Continued)
If you wish to hold the current page without updating
HOLD
INDEX
Subtitles
View in
multi
window
1
Stop automatic updating
■ To resume
•
FASTEXT mode only
Receives input signals automatically when playback starts or
satellite receiver is switched on
••
■
•
Select the external input
Dependant on DVD/VCR setup
2
Factory setting is "P888" (subtitle service) on blue button.
Watch TV and Teletext in two windows at once
•
■ When connecting with SCART as example 2 or 3 (p. 8 and p. 9)
If input mode is not switched automatically
Perform
and
View subtitles by pressing STTL button
•
Turn the TV on
Input signals are automatically identified by the SCART (pin 8) terminal.
This function will be available for HDMI connection too (p. 43).
Return to the main index page
Operations can be made only in Teletext screen.
(AV mode screen)
Screen display
Terminal AV1
As page is
displayed
(List mode only)
•
press
and
hold
Corresponding
colour button
If you wish to use
Subtitles, do not
change number on
blue button.
3
EC2
EC3/RGB
AV3/RGB
―
(S-video input) (S-video input) (S-video input)
(RGB input)
(RGB input)
Component PC HDMI1 HDMI2
Component PC HDMI1 HDMI2
―
―
EC/
HDMI1 HDMI2
connected to the equipment
Displays the selected connector
The number changes to white.
red
press
and
hold
red
green
Appears at top of the
screen
■ To return to TV
■ To view specific sub page
Enter the
4-digit number
blue
•
example: P6
Sub pages:
The number of sub pages varies depending on the broadcasters (up to 79 pages).
It may take some time for searching, during which time you can watch TV.
View theTV picture while searching for a teletext page
Teletext automatically updates itself when new information becomes available.
Changes to TV screen temporarily
P108
yellow
•
Appears
when
updating is
completed
(You cannot change the channel.)
yellow
View the
updated
page
The news page provides a function that indicates arrival of latest news ("News Flash").
•
••
••
•
yellow
AV2/
AV3/
S-video S-video
HDMI1/2
green
yellow
blue
AV4/ Component/ HDMI1/
HDMI2
S-video
PC
PC
(twice)
example: AV1
red
yellow
blue
When colour bar disappears
Press any coloured buttons
You can also select the connector using the TV/AV button on the front panel of the TV.
Press the button repeatedly until you reach the connector to view.
Note
If the external equipment has an aspect adjustment function, set to "16:9".
For details, see the manual of the equipment or ask your local dealer.
HDMI (p. 43)
Some Panasonic VCR and DVD equipment connected to the TV unit can be directly operated with the remote control.
VCR / DVD switch
Select VCR / DVD
Standby
Set to Standby mode / Turn on
Play
Playback videocassette / DVD
Stop
Stop the operations
Rewind / Skip / Search
VCR: Rewind, view the picture rapidly in
reverse
DVD: Skip to the previous track or title
Press and hold to search backward
Fast-forward / Skip / Search
VCR: Fast-forward, view the picture
rapidly forward
DVD: Skip to the next track or title
Press and hold to search forward
Pause
Pause / Restart
DVD: Press and hold to play at slow speed
Programme Up / Down
Select programme
Record
Start recording
Watching VCR, DVD and Satellites
Viewing Teletext
Enter new page number
••
■ To change stored pages
View sub page (Only when teletext is more than one page)
18
Auto input
selection
AV4
AV4
AV4S
Select the connector
AV1
Watch
TV while
waiting
for update
AV1
EC1/RGB
AV1/RGB
AV3
AV3
AV3S
blue
Colour button you
want to change
View sub
page
Manual input
selection
AV2
AV2
AV2S
Viewing
Store frequently viewed pages
(only on first 25 channels on Programme Guide)
in the colour bar
Store
frequently
viewed
pages
Watching VCR, DVD and Satellites
19
How to Use Menu Functions
•M a i n m e n u
How to operate (p. 22 and p. 24)
P i c t u r e me nu
Sound menu
S e t u p m e nu
Picture menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
3D-COMB
Advanced setting
Dynamic
-
+
+
+
+
Only available in NTSC signal
Not available in PC
Only available in NTSC / PAL
Only available in PC
Normal
On
Off
On
Access
Ma in me n u
P ic tu re me n u
Sound menu
PC setup
Input resolution
Clock
H-pos
V-pos
Clock phase
Sync
VGA
Programme edit
H&V
Prog.
S e tu p me n u
(p. 31)
change or access
select
W / B High
W / B High
W / B Low
W / B Low
Gamma
R
B
R
B
2.2
(p. 31)
+
+
-
+
PC setup
Q-Link
AV2 out
Control with HDMI
Teletext
Off timer
Volume correction
Side panel
Power save
Power on preference
Tuning Menu
DVB Setup Menu
Owner ID
Shipping condition
Add
Move
Download
CH44
AUTO SETUP IN PROGRESS
SEARCHING :
PLEASE WAIT
Only available in AV, PC, HDMI and
component
Off
Off
TV
Access
Access
Access
Access
21
Tuning Menu
68
Exit
Return
Access
Access
Access
Programme edit
Auto setup
Manual tuning
1
CH44
Not available in DVB
Only available in HDMI
Lock
Off
Off
Off
Off
Off
Only available in PC
Access
AV2
Monitor
On
FASTEXT
Off
(p. 32)
Off
Music
Off
Auto
Name
ABC
XYZ
FTP
123
456
Manual tuning
Shipping condition
21
All tuning data will be erased
C
68
Search down/up
Store
Exit
Return
9 Direct entry
0
DVB Timer Programming
Thu 05/08/04 18:49
Start
Exit
Return
(p. 34)
■ Choose from among alternatives
Normal
Changed
■ Adjust using the slide bar
Access
Access
Access
Access
Access
eng
Timer Programming
Yo u n o w h a v e t h e o p p o r t u n i t y
to enter your details and
help the police crack crime
see instruction book
Owner ID
PIN NUMBER
NAME
HOUSE NO
POSTCODE
:
:
:
:
∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
Profile Edit
Child Lock
DVB Tuning Menu
DVB System Setup
Multi Audio
End
18:00
20:00
120 Off
Ext
7/8 SA
21:30
22:30
60 Off
Ext
min.
Media
(p. 37)
(p. 28 and p. 36)
All Services
Profile 1
1 BBC ONE Wales
2 BBC 2W
0123456789
7 BBC THREE
Change character
Select character
Store Owner ID
Exit
10 BBC FOUR
30 CBBC Channel
31 CBeebies
40 BBC NEWS 24
■ Go to the next screen
1 BBC ONE Wales
2 BBC 2W
7 BBC THREE
Access
30 CBBC Channel
51 BBCi
89 BBC Radio Wales
90 BBC Radio Cymru
Displays the next
screen
DVB Auto Setup
Please Wait !
NTSC (National Television System Committee): One of television signal used in USA, etc.
HD signal: High-definition signal
DVB Auto Setup
Add New Service
New Service Message
Signal Condition
(p. 29)
21
68
Prog. Channel Service Name
DVB Tuning Menu
Access
Access
On
Access
(p. 30)
NetID.
30 BBC NEWS 24
12302
4158
9
5
30 BBCI
12302
4158
9
6
30 CBBC Channel
12302
4158
9
7
30 BBC Radio Wales
12302
4158
9
8
30 BBC Radio Cymru
12302
4158
9
This will take about 3 mins.
Signal Condition
CH30 1 BBC ONE Wales
0
Common Interface Module
Preferred Subtitles
System Update
Display Timeout
5
10
Common Interface
Access
Slot 1: No module inserted
English
Access
Access
System Update
3 seconds
(p. 26)
20
TS ID. Quality
4
DVB Programme
Signal Quality
Signal Strength
DVB System Setup
Advanced
(p. 29)
Child Lock Service List
Moved
Tuning Menu
Start
6/8 FR
3 ITV1
Profile Editor
(p. 35)
Sharpness
Date
1 BBC1
DVB Setup menu
Number and positions
of alternatives
Colour balance
Pos. Name
How to Use Menu Functions
(picture, sound quality, etc.)
-
Chan.
CH44
CH51
CH41
CH47
CH37
•
Sound menu
Bass
Treble
Balance
Headphone volume
NICAM
Mode
SRS TruSurround XT
HDMI1 input
:
:
:
:
:
Delete
Setup menu
Advanced setting
1
2
3
4
5
Auto Update Search in Standby
System Update Search Now
Software Licence
On
Access
Access
21
How to Use Menu Functions
Various menus allow you to make settings for the picture, sound, and other functions.
■ Menu list
•
Menu
Setup menu (p. 24)
1
Display menu
2
Select the menu
•
Displays the functions that can be set
(varies according to the input signal)
Main menu
Picture menu
Viewing mode
select
Picture menu
Dynamic
select
Normal
On
Off
On
(example: Picture menu)
4
Adjust or select
Picture menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
3D-COMB
Dynamic
(example: Picture menu)
■ Choose from among alternatives
store
(Required by some
functions)
■ Adjust using the slide bar
Sharpness
Moved
■ To return to the
previous screen
•
22
Note
To initialize all settings
"Shipping condition"
(p. 34).
■ To reset the setting
•
•
Sound menu
at any time
Tint
With an NTSC signal source connected to the TV, the picture hue can be adjusted to
suit your taste
Colour balance
Allows you to set the overall colour tone of the picture (Cool / Normal / Warm)
Colour
management
Automatically adjusts colours to vivid ones (Off / On)
P-NR
Picture Noise Reduction
Automatically reduces unwanted picture noise (Off / Min / Mid / Max)
Not valid on PC signal
3D-COMB
Occasionally, whilst viewing still or slow moving pictures, colour patterning may be seen
Set to On to display sharper and more accurate colours (Off / On)
For PAL or NTSC signal reception only
Not valid on RGB, S-Video, components, PC, HDMI and SD Card
Analogue mode only
•
••
•
Bass
Increases or decreases level to enhance or minimise lower, deeper sound output
Treble
Increases or decreases level to enhance or minimise sharper, higher sound output
Balance
Adjusts volume level of right and left speakers
Headphone volume
Adjusts the volume of the headphones
NICAM
NICAM (Near Instantaneous Companded Audio Multiplex)
A format for digital sound over television
Reproduces stereo sound (Off / On)
Off if reception is poor (FM monaural sound)
Analogue mode only
Mode
Sound quality can be improved when watching music scene or drama (Music / Speech)
SRS TruSurround XT
SRS TruSurround XT® creates a high quality surround sound effect using just two
speakers from the source which can output surround encoded signals (Off / On)
HDMI1 input
Select to fit the input signal
(Auto / Digital / Analogue) (p. 43)
Auto
: Automatic detection of digital or analogue sound source
Digital
: HDMI cable connection
Analogue : HDMI-DVI adapter cable connection
HDMI input mode only
HDMI2 terminal is for digital signal only
No setting for HDMI2 available
Normal
Changed
■ To return to TV
Increases or decreases the levels of these options according to your personal preference
Resets each Viewing mode (Dynamic / Normal / Cinema) to the default
settings.
P-NR in Picture menu is reset to off.
Aspect mode is also reset to Auto aspect.
••
••
Advanced
Number and positions
of alternatives
Colour balance
Contrast
Brightness
Colour
Sharpness
change
Normal
On
Off
On
Selects four different screen settings (Dynamic / Normal / Cinema / Auto)
In each Viewing mode setting, Contrast, Brightness, Colour, Sharpness, Tint (in NTSC
only), Colour balance, Colour management and 3D-COMB can be adjusted and stored
to suit your particular viewing requirement (e.g., you may require different settings for
viewing sports, films, news etc.)
Changes to any settings in a viewing mode will affect all signal sources: RF, AV1, AV2,
AV3, AV4, Component, PC, HDMI and SD Card
Changes will be stored automatically. By analysing and processing the incoming
picture, all four modes feature automatic enhancement
How to Use Menu Functions
(picture, sound quality, etc.)
3
Select the item
Adjustments / Configurations (alternatives)
•
(example: Picture menu)
Adjust by each viewing mode
Setup menu
Picture menu
access
Sound menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
3D-COMB
Item
••
•
A different menu will be displayed while PC or SD Card is used. (p. 31 and p. 39)
In AV mode, the Sound menu gives a reduced number of options.
23
How to Use Menu Functions
•
Picture menu, Sound menu (p. 22)
1
Display menu
2
Select "Setup menu"
•
■ Menu list
Item
Menu
Displays the functions that can be set
(varies according to the input signal)
Main menu
Picture menu
Sound menu
Q-Link
Selects which AV terminal is to be used for data communication between this TV and a
compatible recording equipment (AV2 / AV3) (p. 42)
AV2/AV3 out
Chooses the signal to be transmitted from the TV to Q-Link (Analogue / DVB / AV1 /
AV2 / AV3 / AV4 / Monitor)
Monitor: Image displayed on screen
Component, PC and HDMI signals cannot be outputted
Control with HDMI
Control with HDMI function (Off / On) (p. 44)
Teletext
Analogue teletext display mode (FASTEXT / List) (p. 17)
Off timer
Sets the time the unit automatically turns Off. (Off / 15 / 30 / 45 / 60 / 75 / 90) (minutes)
Volume correction
Adjusts volume for AV, PC, HDMI and component mode
Side panel
Increases the brightness of the side panel (Off / Low / Mid / High)
The recommended setting is "High" to prevent panel "after-image"
Power save
Reduces brightness of picture to economise on power consumption (Off / On)
Power on preference
Set to "TV" to view picture from TV tuner.
Set to "AV" to view input from an external equipment connected to a SCART terminal,
e.g. satellite receiver
(TV / AV)
The external equipment must be switched on and sending a control signal for
automatic switching at power on to occur
Tuning Menu
Edits or sets channels (Analogue) (p. 32)
select
access
Adjustments / Configurations (alternatives)
••
Setup menu
AV2
Monitor
On
FASTEXT
Off
Off
Off
TV
select
Adjust or select
change or access
■ Choose from among alternatives
Number and positions
of alternatives
Q-Link
store
(Required by some
functions)
Access
Displays the next
screen
■ To return to the
Timer
Programming
Records future programmes (p. 36)
Profile Edit
Creates list of favourite programmes (p. 29)
Child Lock
Locks a DVB programme channel to prevent access to it (p. 29)
DVB Tuning
Menu
Auto Setup, Add New Service, New Service Message, Signal Condition (p. 30)
DVB System
Setup
Common Interface Module, Preferred Subtitles, System Update, Display Timeout
(p. 26)
Multi Audio
Chooses the sub voice for watching DVB (Alternatives vary depending on the
broadcaster)
Advanced
at any time
DVB Setup Menu
■ Go to the next screen
■ To return to TV
•
AV2
Changed
Tuning Menu
•
How to Use Menu Functions
(picture, sound quality, etc.)
Q-Link
AV2 out
Control with HDMI
Teletext
Off timer
Side panel
Power save
Power on preference
Tuning Menu
Owner ID
Shipping condition
Setup menu
4
Setup menu
•
3
Select the item
previous screen
•
24
Note
To initialize all settings
"Shipping condition"
(p. 34).
••
Owner ID
Inputs the owner ID (p. 35)
Shipping condition
Resets all settings, for example, when moving house (p. 34)
A different menu will be displayed while PC or SD Card is used. (p. 31 and p. 39)
In AV mode, the Setup menu gives a reduced number of options.
25
DVB Settings (DVB mode)
The "DVB Setup Menu" provides access to various advanced features.
1
If in Analogue mode
2
Display the menu
3
Select "Setup menu"
Main menu
Picture menu
Normally pay-TV services will appear without
If pay-TV services does not appear, perform
Common Interface Module
Preferred Subtitles
System Update
Display Timeout
access
select
Access
access
select
Language
of subtitles
3 seconds
red green yellow blue
DVB System Setup
Common Interface Module
Preferred Subtitles
System Update
Display Timeout
set
•
DVB System Setup
select
Update
unit's
software
system
Select a function and set
System
Update
OK
■ To display subtitles (p. 13)
select
3 seconds
Select "System Update"
Common Interface Module
Preferred Subtitles
System Update
Display Timeout
On-screen operation guide
may not correspond to the
remote control buttons.
English
Download new software to TV.
For details (p. 48)
access
access
English
Access
select
3 seconds
If System Update is performed,
the software will be updated (it
may change TV functions). If you
do not wish to do so, set "Auto
Update Search in Standby" to
Off.
Select "Auto Update Search in Standby" and then select "On" or "Off"
System Update
Auto Update Search in Standby
System Update Search Now
Software Licence
set
On
•
select
■ To update immediately
On: Automatically performs
a search in standby and
downloads an update, if any
software updates are available
Select "System Update Search Now"
Searches for an update (for several min.)
and displays a corresponding message if any
Downloads (for about 20 min.)
■ To view software licence information
Select "Software Licence"
If you exit after , the setting is not stored after
turning off the unit.
•
Select "Preferred Subtitles" and set the language
Preferred
Subtitles
Timer Programming
Store
•
The features that appear on
screen are dependent on the
contents of the selected CI
module.
For more details, see the
manual of the CI module, or
check with the broadcaster.
access
English
Coloured characters
DVB Setup menu
Access
eng
and .
and .
Follow the on-screen instructions
example: select, go
Select "DVB System Setup"
Profile Edit
Child Lock
DVB Tuning Menu
DVB System Setup
Multi Audio
•
DVB System Setup
Setup menu
AV2
Monitor
On
Off
Off
Off
TV
Access
CI module
Select "Common Interface Module"
Select "DVB Setup Menu"
•
Information
banner
display time
Display
Timeout
26
•
•
Insert or
remove
straightly
and
completely
Advanced
7
Common
Interface
Module
Turn Off MAINS power On / Off switch
whenever inserting or removing the CI
module.
If a view card and a card reader
come as a set, first insert the card
reader, then insert the view
card into the card reader.
Do not insert the module up side down.
•
■ To return to TV
6
CI slot
DVB Settings (DVB)
(pay-TV, subtitles, etc.)
IDTV
•
•
Pay-TV
Q-Link
AV2 out
Control with HDMI
Off timer
Side panel
Power save
Power on preference
DVB Setup Menu
Owner ID
Shipping condition
(Rear of the TV)
Caution
Setup menu
5
Insert the CI module (optional)
Select DVB
Sound menu
4
The Common Interface Module menu provides access to software contained on Common
Interface (CI) Modules.
Display
Set how long the information banner (p. 13) stays on screen
Select "Display Timeout" and set the time
DVB System Setup
Common Interface Module
Preferred Subtitles
System Update
Display Timeout
set
English
3 seconds
•
0 (none displayed) to 10 sec.
in 1-sec. increments
select
27
Profile Edit / Child Lock
(DVB mode)
Your favourite channels can be listed, and control channel audience.
1
Create your favourite channel list (Profile) from various broadcasters (up to 4: Profile 1 to 4).
The list is added to "Category" in TV Guide (p. 14) and information banner (p. 13) and then
easily accessed.
A channel is added
Select a channel and add it to the list
If in Analogue mode
Select DVB
Profile Editor
Profile Editor
All Services
Profile 1
All Services
1 BBC ONE Wales
7 BBC THREE
10 BBC FOUR
2
Main menu
Picture menu
5
To change
the category
blue
■ To edit Profile
To move the channel
access
To delete the channel
•
access
To delete all channels
store
green
Select the new
Confirm green
•
•
Store
red
position
select
yellow
blue
Channel numbers (Known as logical channel numbers) cannot be changed, due to
broadcast restrictions.
select
You can lock specific channels and control who watches them.
(When a channel is selected, a message appears; by entering the PIN number, you can
watch the channel.)
Enter the PIN number (4 digits)
Child Lock-PIN Entry
Please enter new PIN
PIN
DVB Setup menu
Access
Access
access
eng
select
****
•
•
Enter the PIN number twice at first
setting.
Make a note of the PIN number in
case you forget it.
•
To cancel
Select the locked channel
Select "Child Lock Service List"
Child Lock
How to set
31 CBeebies
Change PIN
Child Lock Service List
Control
channel
audience
access
Access
select
Select the channel to be locked
Child Lock Service List
Child Lock
select
Advanced
■ To return to TV
6
To add all channels
to the list
To name the Profile
Timer Programming
IDTV
30 CBBC Channel
•
•
Select "Profile Edit" or
"Child Lock"
Profile Edit
Child Lock
DVB Tuning Menu
DVB System Setup
Multi Audio
10 BBC FOUR
Select the field of Profile to edit and:
Setup menu
AV2
Monitor
On
Off
Off
Off
TV
Access
green
red
Select "DVB Setup Menu"
Q-Link
AV2 out
Control with HDMI
Off timer
Side panel
Power save
Power on preference
DVB Setup Menu
Owner ID
Shipping condition
To display
another Profile
•
7 BBC THREE
select
Profile Edit / Child Lock
(DVB)
Setup menu
31 CBeebies
Profile
Edit
Select "Setup menu"
Sound menu
4
List
favourite
channels
Profile 1
1 BBC 2W
2 BBC 2W
•
3
30 CBBC Channel
Display the menu
1 BBC ONE Wales
yellow
2 BBC 2W
1 BBC ONE Wales
2 BBC 2W
set
7 BBC THREE
30 CBBC Channel
51 BBCi
89 BBC Radio Wales
90 BBC Radio Cymru
Appears when the channel is locked
•
•
To lock all channels
yellow
To cancel all channel locks
blue
■ To change the PIN number
Select "Change PIN" in
•
28
and enter a new PIN number twice.
Note
Setting "Shipping condition" (p. 34) or "DVB Auto Setup" (p. 30) erases the PIN number
and all settings.
29
DVB Tuning Menu
(DVB mode)
You can re-tune all TV channels when moving house or search for new services which may have recently
started broadcasting.
If in Analogue mode
1
Displaying PC Screen on TV
The screen of the PC connected to the unit can be displayed on the TV.
You can also listen to PC sound with the audio cable connected. To connect PC (p. 46)
Select the external input
1
Select DVB
To
next
page
blue
Display the menu
2
2
Select
"DVB Setup Menu"
•
access
Menu
select
Select "DVB Tuning Menu"
DVB Setup menu
Timer Programming
Profile Edit
Child Lock
DVB Tuning Menu
DVB System Setup
Multi Audio
access
Access
select
eng
Select the function and access
6
To make settings
"How to Use Menu Functions"
Item
Access
White balance of bright red area
W/B High B
White balance of bright blue area
Gamma
(2.0 / 2.2 / 2.5 / S Curve)
Input
resolution
Switches to a wide view
VGA (640 x 480 dots), WVGA (852 x 480 dots),
XGA (1,024 x 768 dots), WXGA (1,366 x 768 dots)
Options change depending on signals
DVB Auto Setup
Automatically sets the DVB channels in the area.
The current setting is erased.
If a Child Lock PIN number (p. 29) has been set, it must be entered again.
Add New Service
Adds a new DVB service.
A new service is added to the DVB channel list, when found.
The new service is added with the current settings saved as they are.
••
••
Selects whether to give a notification message
when a new DVB service is found.
(On / Off)
Selecting OK (Auto Setup) will delete current
Profile and Childlock settings.
Signal Condition
Select a channel and check the DVB signal
condition.
Use for adjusting the direction of the aerial.
Signal Quality:
Green bar
Good
Yellow bar
Poor
Red bar
Bad (Check the aerial)
•
••
•
Set to the minimum level if noise occurs
Adjusts horizontal position
Adjustments / Configurations
New Service
Message
•
•
New DVB Service Found!
Press OK to start Auto Setup
Press EXIT to lgnore.
Warning! Selecting Auto Setup will delete
current Profile and Childlock settings
H-pos
PC
setup
Adjusts vertical position
V-pos
Clock phase
Sync
Signal Condition
CH30 1 BBC ONE Wales
DVB Programme
Signal Quality
Signal Strength
0
5
10
•
Advanced
White balance of dark blue area
select
Setup menu
DVB Tuning Menu
30
Item
and
repeatedly adjusted
White balance of dark red area
W/B Low B
Clock
Menu
Adjustments / Configurations (options)
W/B High R
Advanced
W/B Low R
setting
change or access
On
(p. 20)
Viewing mode, Contrast, Brightness, Sharpness, Colour balance (p. 23)
DVB Tuning Menu
DVB Auto Setup
Add New Service
New Service Message
Signal Condition
to
Displaying PC Screen on TV
DVB Tuning Menu (DVB)
■ PC menu setting (changed as desired)
•
•
select
Picture menu
•
4
5
Corresponding signals
(p. 49)
If "H-freq." or "V-freq."
is shown in red, the
signals may not be
supported.
Displays PC screen
■ To return to TV
access
Setup menu
No data is stored
if an Auto Setup
sequence is
interrupted.
(Press twice)
Main menu
Picture menu
Sound menu
•
•
yellow
Select "Setup menu"
3
■ To return to TV
Select "PC"
HDMI1/2
Eliminates flicker and distortion
Adjust after Clock adjustment
•
•
Set to the minimum level if noise occurs
Chooses another synchronous signal if the image is distorted (H&V / On G)
H&V : by the horizontal and vertical signals from your PC
On G : by the green signal from your PC (if available)
•
Volume correction, Side panel, Power save (p. 25)
Sound menu (p. 22)
31
Editing and Setting Channels
(Analogue mode)
The analogue channel settings can be changed according to your needs and reception conditions.
1
Programme edit
Prog.
1
2
3
4
5
Display the menu
Programme
edit
Select "Setup menu"
Name
Lock
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
select
Setup menu
Select "Tuning Menu"
AV2
Monitor
On
FASTEXT
Off
Off
Off
TV
Access
Move
select
Cursor
Download
■ To delete
■ To change the name of the broadcaster
red
After confirming, press
displayed when selecting channels
red
Prog.
green
After confirming, press
■ To move
1
2
3
4
5
green
yellow
Select new
position
•
Name
Lock
CH44
CH51
CH41
CH47
CH37
XYZ
FTP
123
456
Off
Off
Off
Off
Off
Select the
character
Repeat
To next
character
Usable characters
■ To lock
information to a Q-Link
compatible equipment
connected to the unit
select
:
:
:
:
:
Chan.
ABCDEFGHIJKLMNOPQRST
UVWXYZ+-. 0123456789
yellow
■ To download channel
access
Select the
"Name" field
Programme edit
■ To add
Select the
"Lock" field
Programme edit
Prog.
1
2
3
4
5
Automatically
transmitted
(for a few sec.)
For details (p. 42)
blue
•
Store
:
:
:
:
:
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
Select "On"
"Off" to
unlock
You cannot select the channel with numeric
buttons or the "C" button when locked.
(
)
Select the function
5
6
Tuning Menu
Programme edit
Auto setup
Manual tuning
Access
Automatically set the channels received in the area
access
Settings are made automatically
Start Auto setup
select
start
AUTO SETUP IN PROGRESS
SEARCHING :
PLEASE WAIT
WARNIN G
All analogue tuning
data will be erased
Auto setup
21
Start Auto Setup
Exit
Return
•
(Press repeatedly until "Tuning Mode" appears)
or
•
-
Set
manually
(Change programme position or start searching channels)
(Store)
(Repeat)
■ To return to TV
Programme
position (flash)
Channel number
(flash)
Channel
(Manual tuning screen)
68
Exit
Return
When the operation is completed,
the broadcast of programme
number "1" will appear.
•
•
•
The settings are
downloaded to a Q-Link
compatible equipment
connected to the unit.
All previous settings are
erased.
No data is stored if an
Auto setup sequence is
interrupted.
To freely change settings after Auto setup
(Access "Manual tuning")
(Select programme position or channel number)
Selected item will flash.
or
CH44
Advanced
Set
automatically
How to set
For Manual tuning, using the buttons on
the front of the set ("Manual tuning" on p. 33)
32
3 FTP
Edit
equipment
Setup menu
Add
Channel
Editing and Setting Channels
(Analogue)
■ Delete
■ Add
■ Move
■ Change
name
■ Lock
■ Download to
access
Sound menu
Q-Link
AV2 out
Control with HDMI
Teletext
Off timer
Side panel
Power save
Power on preference
Tuning Menu
Owner ID
Shipping condition
Chan.
CH44
CH51
CH41
CH47
CH37
•
Main menu
Picture menu
4
:
:
:
:
:
Delete
Edit
channels
3
Name
Select the channel to edit
Select Analogue
2
■ To return to TV
Edit the analogue programme position settings
If in DVB mode
Manual
tuning
1
CH44
Select the programme position
and search through the channel
Programme
position
search
1
Manual tuning
C
:
:
:
:
Search
Move cursor
To store
To exit
21
STR
0
68
Search down/up
Store
Exit
Return
9 Direct entry
Repeat
and
Channel
•
CH44
21
Manual tuning
-, +
TV / AV
STR
F
Store
•
The
programme
position
blinks.
Note
If a VCR is
connected with
only the RF
cable, select
programme
position "0".
68
F
-/
+/
TV / AV
33
Restore Settings
Owner ID
Resets the TV to its original condition, i.e. no channels tuned in.
All settings other than "Owner ID" (channels, picture, sound quality, etc.) are reset.
Entry of the security code (PIN number) and "personal information" (your name, address and post code).
In the unfortunate event of theft it will help the Police to determine the owner.
If you have skipped the Owner ID input in "Auto Setup" (p. 10), and input it later, start from .
If you input the Owner ID in "Auto Setup" (p. 10), perform .
Display the menu
1
1
Display the menu
2
Select "Setup menu"
Mai n m enu
P i ct ure m enu
Select "Setup menu"
2
Main menu
Picture menu
Select "Owner ID"
3
access
select
Setup menu
Setup menu
■ To return to TV
■ To return to TV
AV2
Monitor
On
FASTEXT
Off
Off
Off
TV
access
select
Access
How to set
4
select
Enter the 4-digit PIN number of your choice
Access
To change the stored information
Yo u n o w h a v e t h e o p p o r t u n i t y
to enter your details and
help the police crack crime
see instruction book
How to set
Owner ID
PIN NUMBER
NAME
HOUSE NO
POSTCODE
:
:
:
:
Enter the
PIN number
-
∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗∗
0123456789
Characters
Check the message and initialise
Input
owner ID
All tuning data will be erased
Shipping
condition
set
Select
the entry field
Owner ID
Select
character
Start
Exit
Return
Follow the on-screen instructions
•
"Auto Setup" will automatically start when MAINS power On / Off switch is next
turned On. (p. 10)
■ To re-tune TV channels only, e.g. after moving house
••
34
•Enter your name, address, and post code, in that order
Make a note of the PIN number in case you forget it.
Shipping condition
Restore
Settings
DVB: "DVB Auto Setup" (p. 30)
Analogue: "Auto setup" (p. 33)
Entry field
To next
character
Store
store
Advanced
4
access
Owner ID
Restore Settings
Setup menu
AV2
Monitor
On
FASTEXT
Off
Off
Off
TV
• •
Q-Link
AV2 out
Control with HDMI
Teletext
Off timer
Side panel
Power save
Power on preference
Tuning Menu
Owner ID
Shipping condition
Select "Shipping condition"
Q-Link
AV2 out
Control with HDMI
Teletext
Off timer
Side panel
Power save
Power on preference
Tuning Menu
Owner ID
Shipping condition
select
S et up m enu
Sound menu
3
access
Sound menu
To check the "personal information" stored
Hold down for
about 6 sec.
Displays the information
on the screen
(for several sec.)
Owner ID
NAME :
HOUSE NO :
POSTCODE :
•
The PIN number is
not displayed.
A
(Press twice)
35
Recording Controls
Timer Programming (DVB mode) from Menu
Start making
the settings
The Timer programming menu allows you to choose programmes that you wish to record. At the correct time, the DVB
system will switch on and tune to the correct station (even if the TV is in Standby mode). If the recording equipment is
compatible with Q-Link or similar technologies (p. 42) and connected to the TV’s AV3 terminal using a SCART cable
(p. 46), you do not need to programme the device – the DVB system will control the recording process.
TV Guide may also be used to set timer programmes. (p. 14)
If in Analogue mode
1
DVB Timer Programming
Previous
timer
programming
event
Main menu
Picture menu
Sound menu
S e t u p me n u
■ To return to TV
recording
5
6
7
8
Caution
36
••
••
select
120 Off
Ext
22:30
60 Off
Ext
Ext : Recording
device
SD : SD Card
Media
Subtitles
(Off / Auto)
Channel
Starting
time
Recording time
(automatic display)
Ending
time
Daily SU-SA: Sunday to Saturday
Daily MO-SA: Monday to Saturday
Daily MO-FR: Monday to Friday
Weekly SA/FR/TH/WE/TU/MO/SU:
Same time on the same day every week
To change a timer programming event
and press
To cancel a timer programming event
Select the programme to be deleted using
access
and press
red
select
Direct TV recording:
You can record the current programme to DVD Recorder or VCR immediately. (p. 42)
access
eng
How to set the details
OK
Turn On the DVB LED
20:00
21:30
Select the programme to be changed using
Correct as necessary (as above)
Access
Store
18:00
7/8 SA
access
DVB Setup menu
Profile Edit
Child Lock
DVB Tuning Menu
DVB System Setup
Multi Audio
6/8 FR
3 ITV1
daily or weekly
(press repeatedly)
Select "Timer Programming"
Timer Programming
1 BBC1
min.
••
•
••
•
Note
Confirm the DVB LED lights (Orange). If not, a timer programming is not available. Press the TIMER button to be On.
A message will appear if you try to programme a timer event which overlaps an already programmed event.
2 min. before the starting time: a reminder message appears.
(To remove the message
OK button; To cancel the programming
EXIT button)
10 sec. before the starting time: in DVB mode, the unit automatically selects the programmed channel.
Cancelling the programming may not be valid immediately before the starting time. In this case, directly operate
the recording equipment to cancel recording.
Please set the Starting time more than 2 minutes interval from the present time. If you want to record, use Direct
TV recording (p. 42).
Advanced
■ To stop
End
one day ahead
Setup menu
AV2
Monitor
On
Off
Off
Off
TV
Access
Start
Date
Select "DVB Setup Menu"
Q-Link
AV2 out
Control with HDMI
Off timer
Side panel
Power save
Power on preference
DVB Setup Menu
Owner ID
Shipping condition
Date
Recording Controls
3
Select "Setup menu"
Set timer
programming
details
Media
Thu 05/08/04 18:49
Pos. Name
, and can
also be entered
with numeric
buttons.
•
2
Current timer
programming
event
set
select
the item
start
Select DVB
Display the menu
4
Repeat the operations as below,
and set items in the order of
to
TV Guide–Electronic Programme Guide (EPG)–Timer Recording
Operate
and
in p. 14 (mode and Guide switches)
•
Select the programme to
There are two styles of display for TV Guide (Landscape / Portrait)
■ To cancel a reserved
programme
(DVB LED Off)
be broadcast
select
Orange DVB LED
The TV must either be On or in standby.
For preparations of a recording equipment, read the manual of equipment.
No other DVB channel can be selected during recording. However you can watch analogue channels.
It may not be possible to record an encrypted programme (which is copy-protected).
set
(Timer
Programming
screen)
DVB Timer Programming
Thu 05/08/04 18:49
Pos. Name
Date
Start
End
1 BBC1
6/8 FR
18:00
20:00
120 Off
Ext
3 ITV1
7/8 SA
21:30
22:30
60 Off
Ext
min.
Select timer
Edit timer
Exit
Return
Delete
0
Turn On the DVB LED
Media
9
■ To check / change / cancel a timer programming event
•
DVB LED
Orange DVB LED
(Rapid blinking during recording)
"Timer Programming" (above)
37
Viewing from card
(MPEG4 Videos and photos)
MPEG4 view : The moving pictures recorded by this unit, DIGA or D-snap can be played back.
Photo view : The still images recorded by the digital camera can be displayed.
•
■ To open
For details on SD Cards,
see p. 50 and p. 54.
Label surface
2
3
Select the SD mode
To change the view (size, repeat, slide show, etc.)
Select “MPEG4 view” or “Photo view”
■ MPEG4 Videos (operate in step
(SD menu screen)
select
SD card
MP E G 4 v i e w
Video
P hot o v i e w
Photo
Display the
menu
access
S e t up
Selected File
M ain m en u
P ictu re m en u
Error display
(images that could not be loaded, etc.)
select
watch
Select
Filename :
Date
:
MOL0010
01/01/2000
(Thumbnail screen)
Date
Movie without sound
Movie for which lock has been set
View the picture
38
••
•
Normal
Off
select
set
During step 5 , you can select:
"Picture menu" (p. 22)
"Sound menu" (p. 22)
Play
Exit
Repeat
Video is repeated after it ends (Off / One file / All)
Menu
List
red
Exit
ZOOM
Rotate 90˚
(anti-clockwise)
■ To change the aspect ratio
•
During zoom mode, you
can move the position
by using the cursor
buttons.
During the playback, no signals are output from the monitor output terminals.
“Date” shows the date on which the recording was made by this unit, DIGA or D-snap. Its format is 01/01/2000
when recordings are made without date signal.
•
or 5 )
Select “Viewing setup”
M ain m en u
P ictu re m en u
•
■
Rotate
Zoom
SD : Return
Video display size (Nomal / Large)
Pause
Playback
Fast forward
(press and hold)
To next video
Stop
Rewind (press and hold)
To previous video
To previous photo
To thumbnail
Rotate 90˚ (clockwise)
To next photo
Adjustments / Configurations (alternatives)
Frame size
Display the
menu
Photos
Select
Item
■ Photos (operate in step
Viewing
setup
••
Frame size
Repeat
Select the functions and access
access
View in g setu p
select
"Picture menu" (p. 22)
Item
select
Viewing setup
Slide show
Interval
Repeat
Access
5sec
Off
set or
access
Advanced
Skip
Search
Stop
SD : Return
Displayed one at a time
Caution
blue
(Display
)
Press the button again to unlock.
Cannot be deleted when locked.
Photos cannot be deleted or locked.
MPEG4 Videos
Pause
•
Operation
guide
red
■ To display the operation guide
■ To return to TV
the SD menu
■ To delete MPEG4 Video
■ To lock MPEG4 Video
Viewing
setup
Delete
■ To return to
Menu
Select
Operation
guide
select
Viewing setup
00001/00028
MPEG4
VIEW MODE
Exit
Volume
•
Select the file to be viewed
•
access
View in g setu p
SD : Return
Lock
5
Select the functions
Sound menu
Play
IDTV
)
Select “Viewing setup”
Me m or y l e f t
4
Press the centre of the card
Push until a
click is heard
Viewing from card (MPEG4 Videos and photos)
Open the cover
•
SD
Card
Insert the SD Card
•
■ To remove
Press
Explanations given use SD card as an example.
1
■ To insert
Adjustments / Configurations (alternatives)
Slide show
Start slide show
To stop in mid-cycle
Interval
Select slide show interval (5 / 10 / 15 / 30 / 60 / 90 / 120sec)
Repeat
Slide show repeat (Off / On)
•
Note
For compatible card type and maximum size, see page 50.
39
Recording to card
The TV channels and AV1 input signals (PAL) can be recorded on the SD card.
To set the recording time and mode / To format the card
Select the SD mode
1
Set
Insert the SD Card (p. 39)
set or access
Select "Setup"
While watching a programme
•
•
•
P hoto v ie w
Recordable time is displayed
if the recording time is not set (p. 41).
Me m ory le ft
Start recording
••
Continue
(Recording is stopped when
the card capacity is full.)
Cancel
To delete unwanted files, see
page 38 step .
(During the confirmation message appears)
IDTV
Select recording time (No setting / 5 / 10 / 15 / 30 / 60 / 90 / 120 / 180min)
No setting : Recorded until the card is full
Card format
Format the card inserted in the SD Card slot (all data is erased)
Do not remove the SD card while formatting. This may cause the card not to
record properly.
•
•
You can confirm the remaining time for recording in each Rec mode.
Select the SD mode
You cannot record the copy protected signals.
If the Off timer function is activated or press the Standby On / Off button on the
remote control during recording, the recording will not stop.
Do not press the MAINS power On / Off switch on the TV during recording.
Otherwise recording will stop and the file will be unreadable.
Do not remove the SD card while recording. The data being recorded and
other data stored on the SD card may become unreadable.
SD recording may not be fully compatible or playable in some PC software or
PDA devices.
When two pictures are shown on the same screen as Multi window functions,
the main window is the one that is recorded. The picture can be switched for
the sub window (p. 13).
Video signal systems other than PAL cannot be recorded.
The signals without video (only audio) cannot be recorded completely.
Select "Memory left"
SD card
Amount left
select
Memory left
access
Recordable time
Economy
Normal
Fine
Super fine
Extra fine
MP E G 4 v ie w
P hoto v ie w
S e tup
••
12MB
15min
5min
3min
1min
Less than 1min
Displays recordable time for each mode
Me m ory le ft
•
40
Rec time
••
To check memory left
Note
This product is licensed under the MPEG-4 patent portfolio license for the personal and non-commercial
use of a consumer to (i) encode video in compliance with the MPEG-4 Video Standard (“MPEG-4 Video”)
and/or (ii) decode MPEG-4 Video that was encoded by a consumer engaged in a personal and noncommercial activity and/or was obtained from a licensed video provider. No license is granted or implied
for any other use. Additional information may be obtained from MPEG LA. See http://www.mpegla.com.
Rec mode
Select image quality (Extra fine / Super fine / Fine / Normal / Economy)
The quality of audio is not changed.
Multi Media Cards do not support the Extra fine and Super fine recording
mode. If the recording is started in these status, recording will automatically
be performed in the Fine mode.
Advanced
••
•
•
•
•
••
Adjustments / Configurations
Recording to card
To stop
Card capacity is not enough.
•
Item
Menu
Cancel
•
Not enough memory
Current setting
Rec time
180min
Rec mode
Economy
Recordable at
15min
access
S e tup
Setup menu
Start recording?
select
MP E G 4 v ie w
■ Should such a message appear
3
Economy
No setting
Access
Rec mode
Rec time
Card format
SD card
2
select
Setup
Since Multi Media Cards do not support the Extra fine and Super fine recording mode, "----" appears.
Time is approximate.
Recordable time of SD Card
Recording mode and approximate time
Size
64MB
128MB
256MB
512MB
1GB
Extra fine
7minutes
14minutes
28minutes
55minutes
1hour 50minutes
Super fine
9minutes
18minutes
37minutes
1hour 10minutes
2hours 20minutes
Fine
23minutes
44minutes
1hour 32minutes
3hours
6hours
Normal
34minutes
1hour 6minutes
2hours 17minutes
4hours 30minutes
9hours
Economy
1hour 21minutes
2hours 35minutes
5hours 20minutes
10hours 40minutes
21hours 20minutes
41
Q-Link Functions
HDMI Functions
Q-Link connects the TV unit and VCR / DVD recorder, enables easy recording and playback.
■ Condition
•
••
■
•
■•
Use the VCR / DVD recorder with the following logos:
"Q-Link", "NEXTVIEWLINK", "DATA LOGIC", "Easy Link", "Megalogic", or "SMARTLINK"
Connect the equipment to this unit’s AV2 or AV3 terminal via a "fully-wired" SCART cable. (p. 46)
Q-Link terminal setup in Setup menu (Q-Link, AV2/AV3 out). (p. 25)
Download analogue channel settings
Perform Auto setup. (p. 33)
When first using this unit, see "Auto Setup". (p. 10)
Perform download to the equipment. (p. 33)
Features available
Some recording equipments are not applicable. Read the manuals of the equipment.
Direct TV Recording:
Recording the current programme in VCR / DVD recorder
immediately.
■ To change DVB channel, stop recording
••
••
••
••
••
•
•
Note
HDMI is the world's first complete digital consumer AV interface complying with a non-compression standard.
If the external equipment has only a DVI output, connect to the HDMI1 terminal via a DVI to HDMI adapter cable (∗2).
When the DVI to HDMI adapter cable is used, connect the audio cable to the audio input terminal.
Audio settings can be made on the "HDMI1 input" menu screen. (p. 23)
Applicable audio signal sampling frequencies (2ch L.PCM): 48 kHz, 44.1 kHz, 32 kHz
HDMI2 terminal is for digital audio signal only.
Use with a PC is not assumed.
If the connected equipment has an aspect adjustment function, set the aspect ratio to "16:9".
These HDMI connectors are "type A".
An equipment having no digital output terminal may be connected to the input terminal of either "Component",
"S-VIDEO", or "Video" to receive analogue signals.
The HDMI input terminal can be used with only the following image signals:
480i, 480p, 576i, 576p, 720p and 1080i. Match the output setting of the digital equipment.
For details of the applicable HDMI signals, see p. 49.
(∗1): The HDMI logo is displayed on HDMI-compliant equipment.
(∗2): Enquire at your local digital equipment retailer shop.
■ Summary of Control functions
Connections
SCART (Q-Link) only
HDMI only
O
O
O
O
(Not when viewing HDMI input)
O
-
Theatre speaker
O
-
O
Power on link
O
O
O
Power off link
O
O
O
Analogue TV tuning download
O
O
-
Easy playback
Direct TV Recording
Information
/ Message
Recording information or if recording is not possible, a message is displayed.
(Only when the programme number is "0" or "AV mode" for some equipment.)
Power
on link
and Easy
playback
When VCR or DVD recorder starts playback or direct navigator or function menu
are activated, the TV is turned on and input mode is switched automatically so
that you can view the content. (Only when TV is in Standby mode.)
Power off
link
When TV is set to Standby mode, the recording equipment is also automatically
set to Standby. (Only when the videocassette or DVD is not active.)
• "DATA LOGIC" (a trademark of Metz Corporation)
• "Easy Link" (a trademark of Philips Corporation)
Read the manuals of the equipment too.
42
Advanced
HDMI and SCART
Function
HDMI Functions
Q-Link Functions
What you
see is
What you
record
When Direct TV Recording is performed, the
recording equipment is automatically turned on if it
is in Standby mode.
The recording equipment is recording from its own
tuner. You can turn the TV off during recording
(Analogue only).
If, during recording from an AV source, you turn the
TV off or change input / programmes, the recording
will be stopped.
When Direct TV Recording is performed while
watching DVB channel, the DVB programme
position is locked and no other DVB channel can
be selected. However you can watch analogue
channels.
HDMI (high-definition multimedia interface) allows you to enjoy high-definition digital images and high-quality sound
by connecting the TV unit and the equipment.
HDMI-compatible equipment (∗1) with an HDMI or DVI output terminal, such as a set top box or a DVD player, can
be connected to the HDMI terminal using an HDMI compliant (fully wired) cable.
About connections, see "External Equipment" (p. 46).
••
•
•
•
•
HDMI connection
• "Megalogic" (a trademark of Grundig Corporation)
• "SMARTLINK" (a trademark of Sony Corporation)
43
HDMI Functions (Continued)
Control with HDMI "
Control"∗
∗Enjoy additional HDMI Inter-Operability with Panasonic products which have "HDAVI Control" function.
HDMI connections to some Panasonic equipment (Panasonic DVD Recorder DIGA, Panasonic Player
theatre, Panasonic Amplifier, etc.) allow you to enjoy easy playback or home theatre.
About connections, see "External Equipment" (p. 46). Read the manuals of the equipment too.
This function needs an HDMI compliant (fully wired) cable.
Non-HDMI-compliant cables cannot be utilized.
Consult your local Panasonic dealer or refer to the URL for applicable equipment: www.panasonic.co.uk
Easy
playback
Preparations
(For the first time / When adding new equipment, reconnecting equipment or changing setup)
You can control the theatre speaker with TV’s remote control.
This function is available when Panasonic Amplifier or Player theatre is connected.
After connection turn the equipment on and then switch the TV unit on.
Select the input mode to HDMI1 or HDMI2 (p. 19), and make sure that an
image is displayed correctly.
1
Display the menu
Select "Home theatre" or "TV speaker"
Display the menu
Main menu
Home theatre
Theatre
speaker
•
■ TV speaker:
••
access
select
Select "Control with HDMI"
TV speakers are active.
When selecting "Home theatre", the sound of TV speakers is mute.
When the equipment is turned off, TV speakers will be active.
Power on
link
When the connected Panasonic equipment starts playback or direct navigator or
function menu are activated, the TV is automatically turned on. (Only when TV is
in Standby mode.)
Power off
link
When TV is set to Standby mode, the connected Panasonic equipment is also
automatically set to Standby.
Setup menu
Q-Link
AV2 out
Control with HDMI
Off timer
Side panel
Power save
Power on preference
DVB Setup Menu
Owner ID
Shipping condition
AV2
Monitor
On
Off
Off
Off
TV
select
Select "On"
(default is On)
It is recommended that you use Panasonic’s HDMI cable.
Recommended part number:
RP-CDHG15 (1.5 m)
RP-CDHG30 (3.0 m)
RP-CDHG50 (5.0 m)
select
••
••
••
••
Advanced
44
Volume up / down
Mute
Displayed when Amplifier or Player theatre is connected.
This may be displayed after disconnecting the equipment.
In this case, set "Control with HDMI" in Setup menu to
"Off", then set to "On" again.
■ To return to TV
•
select
HDMI Functions
S e tu p me n u
4
Setup menu
M a i n me n u
H o me th e a tre
Sound menu
IDTV
access
Sound menu
Adjustment for equipment
(automatically turned on if it is in
Standby mode)
Select "Setup menu"
P ic tu re me n u
3
Picture menu
■ Home theatre:
•
2
Automatic Input switching-When the connected Panasonic equipment is operated,
input mode is switched automatically. When it is stopped operating, input mode is
returned.
Note
Setup the equipment to enable this function. Read the manual of the equipment.
This function may not work normally depending on the equipment condition.
This function may not work normally when Panasonic Player theatre is connected.
The equipment can be operated by TV’s remote control with this function on even if TV is in Standby mode.
Image or sound may not be available for the first few seconds when the playback starts.
Image or sound may not be available for the first few seconds when Input mode is switched.
Volume function will be displayed when adjusting the volume of the equipment.
Easy playback is also available by using the remote control for Amplifier. Read the manuals of Amplifier.
45
External Equipment
These diagrams show our recommendations for how to connect the TV unit to your various equipment.
For other connections, consult the instructions for each piece of equipment, the table below, and the specifications (p. 55).
To watch satellite broadcasts
Satellite receiver
Control with HDMI (p. 44)
DVD recorder or AV amplifier
••
Fully wired HDMI
compliant cable
Fully wired HDMI
compliant cable
Use HDMI2 terminal normally.
When using HDMI2 terminal as Control
with HDMI, select the external input to
HDMI2 for the first time (p. 19).
To record / playback
DVD Recorder / VCR
RF cable
V
L
SCART
cable
R
(Φ3.5 mm
stereo mini
plug)
1
To listen with speakers
Amplifier with speaker system
AV
(AUDIO)
•
within
10 cm
2
(VIDEO)
or
(S-VIDEO)
Y
AUDIO
IN
PC
Camcorder / Game equipment
Pull back the
tabs to open
L
PB
L
R
PR
R
AUDIO
Press the cable
through and close
PC
Computer
Headphones
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
VIDEO
AUDIO
Advanced
To watch DVDs
■ To adjust volume
Conversion adapter (if necessary)
"Headphone volume"
in the Sound menu
(p. 23)
DVD player
(Listening)
■Types of connectable equipment to each connector
Connector
AV1 AV2 AV3
■PC connection
AV4
COMPO
NENT
Y
Recording / Playback
(equipment)
To record / playback videocassettes / DVDs
(VCR / DVD recorder)
To watch DVDs (DVD player)
To watch camcorder images (Video camera)
To watch satellite broadcasts (Set top box)
To play games (Game equipment)
Q-Link
Direct TV Recording
Control with HDMI
: Recommended Connection
AV 3
(Q-Link)
COMPONENT
(Viewing)
46
AV 2
(Q-Link)
External Equipment
AV 1
Ferrite core
or
SCART
cable
AV4
S-V
SCART
cable
(Front of TV)
PB
PR
1
2
A PC may be connected to this TV unit so that the PC screen is displayed and sound is heard from the TV.
PC signals that can be inputted: Horizontal scanning frequency 31 to 69 kHz; vertical scanning frequency
59 to 86 Hz (more than 1,024 signal lines could result in incorrect display of the image).
A PC adapter is not necessary for the DOS/V-compliant D-sub 15-pin connector.
Some PC models cannot be connected to this TV unit.
Note
For details of the applicable PC signals, see p. 49.
Max. display resolution
•
•
••
4:3
16:9
Aspect
•
768 × 720 dots
1,024 × 720 dots
D-sub 15-pin connector signal
5
4
3
2
1
10 9 8 7 6
15 14 13 12 11
(TH-37PX600B)
Pin No.
768 × 768 dots
1,024 × 768 dots
•
(TH-42PX600B)
1,024 × 768 dots
1,366 × 768 dots
(TH-50PX600B)
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
R
GND (Ground)
NC (not connected)
G
GND (Ground)
NC (not connected)
B
GND (Ground)
HD/SYNC
NC (not connected)
NC (not connected)
VD
GND (Ground)
GND (Ground)
NC (not connected)
47
Technical Information
Aspect Ratio
SCART, S-VIDEO and HDMI terminal information
The optimum size and aspect can be chosen, and you can enjoy finer images. (p. 13)
■Auto aspect: Auto aspect determines the best aspect ratio to use to fill your screen. It does this using a four step
process to determine if the picture being viewed is a widescreen picture.
If Auto aspect detects a widescreen signal it switches into the appropriate 16:9 or 14:9 widescreen mode. If Auto aspect
does not detect a widescreen signal then this advanced TV set enhances the picture for optimum viewing pleasure.
The text shown on the screen indicates how Auto aspect determined which ratio to use:
"WIDE" appears in the top left of the screen if a widescreen identification signal (WSS) is found or a signal found
through a SCART terminal. Auto aspect switches to the appropriate 16:9 or 14:9 widescreen ratio. This function
will also work in any aspect mode. "Auto aspect" appears in the top left of the screen if black stripes above and
below the picture are detected. Auto aspect chooses the best ratio and expands the picture to fill the screen. This
process can take several minutes, depending on the darkness of the picture.
Aspect Control Signal
Control signal through SCART
Widescreen signal (WSS)
(pin 8) or HDMI terminal
HDMI
Zoom1 Zoom2 Zoom3 TV AV1 AV2 AV3 AV4 Component AV1 AV2 AV3 HDMI
1
2
O
O
O O O O O O
O O O O
O
O - - - - O O O - - - - O
O
O O - - - O
O
O - - - - O O O O
O
O - - - - O O O - - - O O
O
O
O - - - - - - - O O
O
O
O - - - - - - - O O
O
O
O - - - - O
- - - O O
O
O
O - - - - O
- - - O O
O
O
O - - - - - - - O O
O
O
O - - - - - - - O O
O
O
O - - - - - - - O O
O
O
O - - - - -
Aspect modes
Signal name
SD
HD
TV/AV1/AV2/ Component/HDMI
AV3/AV4
PAL I
PAL 525/60
DVB
M.NTSC
NTSC(AV input only)
525(480)/60i
525(480)/60p
625(576)/50i
625(576)/50p
750(720)/50p
750(720)/60p
1125(1080)/50i
1125(1080)/60i
PC input
Note
Auto aspect
Auto aspect
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
- - - - - - - - - The ratio varies depending on the programme, etc. If the ratio is greater than the standard "16:9",
black bands may appear at the top and bottom of the screen.
If the screen size looks unusual when a widescreen-recorded programme is played back on a VCR,
adjust the tracking of the VCR. (See the VCR manual.)
Aspect mode can be memorized for SD (Standard definition) and HD (High definition) signals separately.
To select the ratio manually: (Only "16:9" or "4:3" in PC mode)
16:9
The best ratio
is chosen and
the picture
expanded to
fill the screen.
16 : 9
Zoom2
Zoom2
14:9
Directly displays
the image at
"16:9" without
distortion
(anamorphic).
Displays a
"16:9" letterbox
(anamorphic)
image fullscreen without
distortion.
14 : 9
Zoom3
Zoom3
4:3
Displays the
image at the
standard "4:3"
without
distortion.
Displays a "2.35:1"
letterbox (anamorphic) image full-screen
without distortion. At "16:9", displays the
image at its maximum (with slight
enlargement).
Updating the DVB software
From time to time, a new version of software for DVB mode may become available for download to enhance
performance or operations of the TV.
A notification banner will appear when you tune to one of the BBC channels, or you can search for a new version
software by using the "System Update Search Now" function (p. 27).
New version 1.00 found.
Do you really want to update the software and reboot the system?
Press OK to download the new version
Press EXIT to lgnore
To download any new software automatically, ensure that the "Auto Update Search in Standby" function in the
System Update menu is set to "On" (p. 27).
The TV will then download new software automatically at night if it is left in standby without any timer programme
in progress.
48
•
During software download and update, DO NOT switch off the TV.
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
RGB status earth
Status RGB
Earth
--Status CVBS
Audio in (L)
Audio earth
Audio in (R)
■ AV3 SCART terminal
(RGB, VIDEO, S-VIDEO, Q-Link)
AV2 - Pins 15 and 20 are dependent on AV2 S-VHS /
VIDEO switching.
Socket Earth
CVBS out (video)
CVBS earth
S.C. - in
Earth
-Earth
-Earth
Audio out (L)
Audio out (R)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
Earth
-Earth
-Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
■ AV4 S-VIDEO 4 pin terminal
Chrominance in
Luminance in
Chrominance earth
Luminance earth
AV3 - Pins 15 and 20 are dependent on AV3 S-VHS /
VIDEO switching.
Socket Earth
CVBS out (video)
CVBS earth
Red in, S.C. - in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Audio out (R)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
RGB status earth
Status RGB
Earth
-Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
■ HDMI terminal
Hot Plug Detect
DDC/CEC Ground
SCL
CEC
TMDS Clock Shield
TMDS Data0−
TMDS Data0+
TMDS Data1 Shield
TMDS Data2−
TMDS Data2+
19
17
15
13
11
9
7
5
3
1
18
16
14
12
10
8
6
4
2
+5V Power
SDA
Reserved (in cable but N.C. on device)
TMDS Clock−
TMDS Clock+
TMDS Data0 Shield
TMDS Data1−
TMDS Data1+
TMDS Data2 Shield
Input signal that can be displayed
∗ Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC (D-sub 15P)
Signal name
525 (480) / 60i
525 (480) / 60p
625 (576) / 50i
625 (576) / 50p
750 (720) / 60p
750 (720) / 50p
1,125 (1,080) / 60i
1,125 (1,080) / 50i
640 × 400 @70 Hz
640 × 480 @60 Hz
640 × 480 @75 Hz
800 × 600 @60 Hz
800 × 600 @75 Hz
800 × 600 @85 Hz
1,024 × 768 @60 Hz
1,024 × 768 @70 Hz
1,024 × 768 @75 Hz
1,024 × 768 @85 Hz
1,280 × 1,024 @60 Hz
Macintosh13” (640 × 480)
Macintosh16” (832 × 624)
Macintosh21” (1,152 × 870)
Note
••
Horizontal
frequency (kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
31.46
31.47
37.50
37.88
46.88
53.67
48.36
56.48
60.02
68.68
63.98
35.00
49.72
68.68
Vertical
frequency (Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
70.07
59.94
75.00
60.32
75.00
85.06
60.00
70.07
75.03
85.00
60.02
66.67
74.54
75.06
Component
HDMI
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
Signals other than above may not be displayed properly.
The above signals are reformatted for optimal viewing on your display.
PC
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
FAQs, etc.
To start downloading press "OK", this may take up to 20 minutes to
complete.
To ignore the new software press "EXIT", but this banner will keep
appearing during the period of new software availability, usually 2 to 3 days.
Note
Socket Earth
CVBS out (video)
CVBS earth
Red in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Audio out (R)
4:3
Displays the
image at the
standard
"14:9" without
enlargement.
(VIDEO, S-VIDEO, Q-Link)
Suitable inputs for AV1 include RGB (Red / Green / Blue).
Technical Information
Displays a
"16:9" letterbox
or "4:3" image
without
distortion.
Zoom1
16:9 14:9 4:3
■ AV2 SCART terminal
(RGB, VIDEO)
•
Zoom1
•
•
••
Auto
aspect
O
O
O
O
O
O
O
O
O
O
O
O
O
■ AV1 SCART terminal
49
Technical Information
Multi Window
You can watch two images at once, such as a TV programme and a DVD. (p. 13)
The TV unit has one tuner. Two programmes cannot be displayed at once.
You cannot select the same input source between Main and Sub screen.
This function cannot be used with a PC, HDMI, SD card, or when progressive signals/1080i signals
(Y, PB, PR) are being inputted.
••
•
FAQs
Before requesting service or assistance, please follow these simple guides to resolve the problem.
If problem still persists, please contact your local Panasonic dealer or Panasonic Customer Care Centre
for assistance. For details (p. 56)
White spots or shadow
images (noise)
Data format for Card browsing
Photo
: Still images recorded with digital still cameras compatible with JPEG files of
DCF∗ and EXIF standards
: Videos recorded with this TV unit , Panasonic DVD recorder or digital camcorder
: FAT12 or FAT16
Video
Data format
Number of pixels
for motion picture
: 320 x 240 (QVGA) or 176 x 144 (QCIF)
Max. number of files : 65,535
Image resolution
: 8 x 8 to 5,120 x 3,840
Sound format
: G.726 (32 Kbps, 8-kHz sampling frequency, monaural)
Compliant card type (maximum capacity): SD Card (1 GB), Multi Media Card (128 MB),
Mini SD Card (512 MB) (requiring mini SD adapter)
Check the latest information on the card type at the following website. (English only)
http://panasonic.co.jp/pavc/global/cs
•
•
∗DCF (Design rule for camera file system): Unified standard established by Japan Electronics and Information Technology Industries Association (JEITA).
Caution
••
••
•
•
Neither image nor
sound is produced
••
••
•
•
Auto aspect is designed to provide you
with the best aspect ratio to use to fill your
screen. For user control please see p. 48.
•
Using TV/AV button please confirm your
selection is S-Video I.e. AV2/S-Video or
AV3/S-Video (p. 19).
100_PANA
P1000001.JPG
P1000002.JPG
P1000003.JPG
P1000004.JPG
3-digit folder number + 5-digit arbitrary characters
•
Time:
••
•
•
The folder and file names may be different depending on the digital camera used.
Do not use two-byte characters or other special codes.
The card may become unusable with this unit if file or folder names are changed.
19:30
20:00
20:30
Prog. type
All Types
21:00
21:30
Check the DVB transmitter.
Adjust the direction of the aerial to another transmitter installed nearby.
Check the analogue broadcast.
If the image quality is poor, check the aerial and consult your nearest dealer.
On Screen messages - I.e. AV1/EC1
•
You can simply clear these by pressing
Press again to redisplay.
.
Direct TV record / Q-Link functions
not recording
•
Please confirm SCART cable and connection. Also please
set "AV2/AV3 out" in the Setup menu (p. 24).
Actions
•
•
•
Contrast is reduced
Permanently lit spots on
screen
Wed 12/05/04 10:46
Category
All Services
•
The function to prevent after-image (p. 5) is activated.
(Not a faulty symptom)
The screen saver is activated when the following
conditions without any user operation for a few minutes:
● no signal in DVB or AV mode
● selected locked channel
● selected invalid channel
Contrast is lowered when the following conditions
without any user operation for a few minutes:
● selected radio channel
● displayed menu (except Tuning menu, Owner ID and
Shipping condition)
Due to production process involved in this technology
this may result in some pixels which are permanently lit
or unlit. This is not a malfunction.
FAQs, etc.
MOL001.ASF
MOL002.ASF
MOL003.ASF
MOL004.ASF
Created automatically
Created automatically
"PRL" + 3-digit arbitrary characters
"MOL" + 3-digit arbitrary characters
Usable characters: 1-byte "a to f", "A to F", and "0 to 9"
Screen
PRL001
logo appears at the
four corners of the screen
4-digit arbitrary characters + 4-digit file number
Usable characters: 1-byte "a to z", "A to Z", "0 to 9," and "_"
Video
SD_VIDEO
DVB TV Guide :Landscape
Wed 12th
Problem
Created automatically
DCIM
No programmes shown on TV Guide
Frequently Asked Questions
Technical Information
S-Video / black and
white picture
Folder structure viewed in PC
Photo
50
Is the unit in "AV mode"?
Is the mains lead plugged into the socket outlet?
Is the TV unit turned On?
Check Picture menu (p. 22) and volume.
Check all required SCART cables and
connections are firmly in place.
Auto aspect
Note
••
•
Check the position, direction, and
connection of the aerial.
•
•
••
•
A JPEG image modified with a PC cannot be displayed.
Images imported from a PC must be compatible with EXIF (Exchangeable Image File) 2.0, 2.1, and 2.2.
Partly degraded files might be displayed at a reduced resolution.
MPEG4 view can only show moving pictures recorded by this unit, Panasonic DVD recorder DIGA or mobile
camera D-snap.
When recording in MPEG4, format the SD card with this unit. The card may not operate properly if formatted with
different equipment.
Memory cards must be formatted with FAT12 or FAT16 in order to be viewed on TV. If the card is not formatted, it
may cause incompatibility with certain memory card adapters. If this happens, reformat the card using your digital
camera.
Reformatting the card will erase the images and pictures stored in it. Refer to your camera manual for more
information.
This function cannot display Motion JPEG and still image not DCF formatted (i.e. TIFF, BMP).
The displayed image size depends on the recorded image size.
•
51
FAQs
On screen messages
Problem
Screen
Chaotic image, noisy
••
Set "P-NR" in the Picture menu (to remove noise). (p. 23)
Check nearby electrical products
(car, motorcycle, fluorescent lamp).
No image can be
displayed
•
Is "Colour" or "Contrast" in the Picture menu set to the
minimum? (p. 23)
Blurry or distorted image
•
Reset channels. (p. 30 and p. 32)
(no sound or low volume)
Sound
No sound is produced
Sound level is low
or sound is distorted
•
••
••
Is "Sound Mute" active? (p. 7)
Is the volume set to the minimum?
Sound signal reception may be deteriorated.
Set "NICAM" (p. 22) in the Sound menu to "Off".
(Analogue only)
Due to the digital reception technologies involved, quality of the DTV signals may be relatively low in
some cases, despite good reception of analogue programmes.
DVB
Interference or
frozen / disappearing
image in DVB
Sound is unusual
•
•
•
••
••
Feature not available
Incorrect PIN Number
Invalid DVB Channel
Invalid system time. Please exit !
Key not available
Max number of Timer already set !
New DVB Service Found!
Press OK start Auto Setup
Press EXIT to Ignore.
Warning! Selecting Auto Setup will delete
current Profile and Childlock settings
New version 1.90 found.
Do you really want to update the
software and reboot the system ?
Press OK to download the new version
Press EXIT to Ignore
No DVB Service found
No module inserted
No recording -Check Tape or Disc
No recording - UNKNOWN REASON
Set the sound setting of the connected equipment to
"2ch L.PCM".
Check the "HDMI1 input" setting in the Sound menu. (p. 23)
If digital sound connection has a problem, select analogue
sound connection. (p. 23)
Is the HDMI cable connected properly? (p. 46)
Turn Off the TV unit and equipment, then turn them On again.
Check an input signal from the equipment. (p. 49)
Use an equipment compliant with EIA/CEA-861/861B.
No Service
No Signal
Please check aerial or local
DVB service availability.
Press OK to start Auto Setup
Please check settings and connections on HDMI devices.
No stations found
Please insert the aerial
Please wait.
Recording in progress
SD
Unable to download, Check Equipment
WARNING
All analogue tuning data will be erased
WARNING
All digital tuning data will be erased
•
•
•
Software successfully updated
Press EXIT to continue
Press EXIT to continueThis service is locked!
Press OK to enter PIN
Timer already expired !
Timer Event Due to Start
1: BBC1 has been
Programmed for recording at 20:00
Timer incorrect !
•
TV unit goes into
"Standby mode"
••
The sleep function is activated.
The TV unit enters "Standby mode" about 30 min.
after broadcasting ends.
The remote control
does not work
••
Are the batteries installed correctly? (p. 6)
Has the TV unit been switched On?
Software Update failed. Please try again later.
Make sure the deleting programme event is with your desire.
The signal is weak. Check the aerial.
Q-Link channel download is in progress.
If you want to unlock, cancel Direct TV Recording (p. 42) or Timer
Programming (p. 36).
Check the Q-Link connection and setting (p. 42).
The impossible source (Component / HDMI / PC) to be record.
The PIN number you entered is wrong.
Invalid DVB channel is selected.
Cannot get the time information. Check the connection of the RF cable.
You cannot select the same input source between Main and Sub
screen when you are viewing in multi window. (p. 13)
Maximum timer programming event is 8.
There is a new DVB station.
There is a new software available.
No DVB signal can be found in Auto Setup.
Check the CI module inserted completely (p. 27).
The tape or disc may be "write protected", missing or damaged.
The equipment may already be recording.
The recording cannot be done by any reason. Check the equipment.
Disc or tape may be full.
The station stops the services.
Check the connection of the RF cable.
Please follow the message.
If it is still failed, consult your local Panasonic dealer.
Communication error in Control with HDMI function (p. 44).
No analogue signal can be found in Auto setup.
A function is in progress.
The recording equipment is recording the programme signal from
its own tuner. You can turn the TV off and leave the equipment
recording in the normal way.
Direct TV recording (analogue mode) will stop if channel or input
source is changed.
The software updating is finished.
Perform "System Update Search Now" in System Update (p. 27).
If it is still failed, there may not be the new software.
The selected channel is locked in Child Lock (p. 29).
Starting time in Timer Programming is already past. Set correctly (p. 37).
This message will appear 2 minutes before timer programming
event due to start.
Set Starting and Ending times in Timer Programming correctly (p. 37).
The timer programme events are overlapped. Cannot record other
channel at the same time. Check the Starting and Ending times in
Timer Programming (p. 37).
The tape or disc is active. Stop the equipment and try again.
Auto setup will be erased all present analogue tuning data (p. 33).
DVB Auto Setup will be erased all present DVB tuning data
(p. 30).
FAQs, etc.
Other
Timer overlap!
Switch the TV unit on again with the equipment on.
Set “Control with HDMI” to “Off”, then set to “On” again.
(p. 44)
Contact the authorized Service Centre.
•
••
•
••
••
•
•
•
••
•
•
•
•
•
•
••
Recording stopped - TV source changed
The SD card cannot be used
even when it is formatted
••
•
••
•
••
••
•
•
•
•
Actions
/ Meanings
Actions
"Shipping condition" will erase all tuning data.
Make sure the operation is with your desire.
On screen messages
Frequently Asked Questions
••
••
Check "Signal Condition". (p. 30)
If "Signal Quality" or "Signal Strength" are displayed in red,
check aerial.
If problem persists, consult your local Panasonic dealer.
Use the remote control to turn Off the TV unit, then turn it On
again.
On screen
messages
Problem
All tuning data will be erased
Are you sure ?
Are you sure you want to delete this timer ?
Press OK to delete timer
Press Exit to return
Bad Signal
DOWNLOAD IN PROGRESS PLEASE WAIT
DVB Tuner Locked
This programme is locked for recording
• •
HDMI
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
“Control with HDMI” function
does not work
52
Actions
53
On screen messages (SD Card)
On screen messages
Is SD Card in?
SD Card is locked
Please unlock to operate
This file is locked
Please unlock to operate
This type of format is not
supported
This type of card is not
supported
Cannot read file
Unrecordable source
SD recording is stopped
Unlock the SD card.
Unlock the file in the card.
The unit does not support the format.
(For the applicable formats and data, see p. 50.)
D
A card not supported by the unit has been inserted.
(For the supported cards, see p. 50.)
The file is broken.
The card memory is full.
The card does not have enough memory to operate.
The file is not readable.
That channel cannot be recorded. (Recording is automatically
stopped.)
Re-insert the card. If the error persists, format
the card. (p. 41)
That operation is not available during recording.
To continue the operation, stop recording.
(For example, changing channels while recording)
Category list ··········· 14
Child Lock ··············· 29
CI module ··············· 27
Clamper ················ 6, 9
Component ············· 49
Connection ········· 8, 46
Control with HDMI
····················· 44, 46
Direct TV Recording
··························· 42
Display Timeout ······ 27
Download to equipment
····················· 10, 33
D-sub 15-pin ··········· 47
DVB Auto Setup ····· 30
DVB LED ············ 7, 15
DVB settings ··········· 26
DVB Tuning Menu ·· 30
DVI·························· 43
No time data
Cannot store time info
Source / Average
Standby condition
Drive method
Ratio
Visible screen size
(No. of pixels)
Since the signal does not have the time information, the date
is recorded as 01/01/2000.
Cautions when handling SD Card :
Do not remove the card while the unit is accessing data ("blue" LED
On) (this can damage card or unit).
Do not touch the pins on the back of the card.
Do not subject the card to a high pressure or impact.
Insert the card in the correct direction (otherwise, card may be
damaged).
Electrical interference, static electricity, or erroneous operation may
damage the data or card.
Back up the recorded data at regular intervals in case of deteriorated
or damaged data or erratic operation of the unit. (Panasonic is not
liable for any deterioration or damage of recorded data.)
Blue LED
WARNING: As with an small object,
SD card can be swallowed by young
children. Do not allow children to
handle SD card. Please remove SD card
immediately after use.
F
FAQs··················51-52
Front door ················· 7
H
HDMI ·················43-45
Hold ·················· 13, 18
Home theatre ·········· 44
I
Information banner ··· 13
Input signal ············· 49
L
Licence ··················· 56
Lock ························ 33
Q
Q-Link ····················· 42
Quick Start Guide 6-11
M
Mains Lead ··········· 6, 8
Maintenance ············· 5
Manual tuning ··· 32, 33
Menu Functions ··20-25
Multi window ······ 13, 50
R
Remote control ····· 6, 7
RGB ·························· 8
S
Sales and Support
Information ········· 56
Satellite receiver
················· 9, 19, 46
SCART ··············· 8, 49
SD Card ······ 38, 50, 54
New Service Message
··························· 30
NICAM ···················· 23
Normalise ··········· 7, 22
O
Off timer ·················· 25
On / Off switch ···· 7, 12
Optional accessories ·· 6
Owner ID ·········· 10, 35
P
PAL ························· 55
PC····················· 31, 47
PIN number 11, 29, 35
P-NR ······················· 23
Power LED ········· 7, 10
Profile Edit ·············· 29
Programme edit ······ 33
T
Teletext ··············16-18
Timer programming
····················· 15, 36
TV Guide ·········· 14, 15
TV speaker ············· 45
Type list ·················· 14
U
Update the software
····················· 27, 48
V
Videos················· 8, 19
Viewing mode ········· 23
W
Z
WSS ······················· 48
Zoom ················ 13, 48
Receiving Systems /
Band name
Aerial - Rear
Operating Conditions
AV1 (Scart terminal)
AV2 (Scart terminal)
AV3 (Scart terminal)
VIDEO
AV4
S-VIDEO
AUDIO L - R
COMPONENT
HDMI1/2
Others PC
AUDIO L - R
Card Slot
Output AUDIO L - R
Dimensions ( W × H × D )
Weight
Note
TH-37PX600B
TH-42PX600B
TH-50PX600B
AC 220-240 V, 50 / 60 Hz / 250 W
AC 220-240 V, 50 / 60 Hz / 270 W
AC 220-240 V, 50 / 60 Hz / 377 W
0.3 W (Without DVB recording) / 20 W (With DVB recording)
AC type
16:9 (Aspect Ratio) / Max 10000:1 (Contrast Ratio)
94 cmV
106 cmV
818 mm (W) × 461 mm (H) ×
920 mm (W) × 518 mm (H) ×
939 mm (diagonal)
1,056 mm (diagonal)
737,280 (1,024 (W) × 720 (H))
786,432 (1,024 (W) × 768 (H))
[3,072 × 720 dots]
[3,072 × 768 dots]
••
127 cmV
1,106 mm (W) × 622 mm (H) ×
1,269 mm (diagonal)
1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
31 W (15.5 W +15.5 W), 10 % THD
Φ 3.5 mm stereo mini Jack × 1
VGA, SVGA, XGA
Horizontal scanning frequency 31 - 69 kHz
SXGA ··· (compressed)
Vertical scanning frequency 59 - 86 Hz
PAL I
:
UHF E21-68.
PAL 525/60:
Playback of NTSC tape from some PAL Video recorders (VCR) or NTSC disc playback
from DVD player and recorder.
DVB
:
Digital terrestrial services via UHF aerial input.
M.NTSC :
Playback from M.NTSC Video recorders (VCR).
NTSC (AV input only) : Playback from NTSC Video recorders (VCR).
UHF
Temperature: 0 °C - 40 °C
Humidity : 20 % - 80 % RH (non-condensing)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in)
21 Pin terminal (Audio/Video in, Audio/Video out, S-Video in, Q-Link)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
RCA PIN Type × 1
1.0 V[p-p] (75 Ω)
Mini DIN 4-pin
Y:1.0 V[p-p] (75 Ω) C:0.286 V[p-p] (75 Ω)
RCA PIN Type × 2
0.5 V[rms]
Y 1.0 V[p-p] (including synchronization) PB, PR ±0.35 V[p-p]
TYPE A Connectors
HIGH-DENSITY D-SUB 15PIN R,G,B/0.7 V[p-p] (75 Ω)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
RCA PIN Type × 2
0.5 V[rms]
SD CARD slot × 1
RCA PIN Type × 2
0.5 V[rms] (high impedance)
977 mm × 629 mm ×
1,077 mm × 689 mm ×
1,266 mm × 802 mm ×
138 (panel part : 95) mm
138 (panel part : 95) mm
138 (panel part : 95) mm
28.5 k Net
32.5 k Net
43.0 k Net
Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
FAQs, etc.
54
Displayed when you press Red colour button to delete a
MPEG4 file. Press OK button to confirm deleting.
External equipment
······················· 8, 46
External input ··· 19, 31
Woofer (Φ80mm) × 2 pcs, Tweeter (23 mm × 100 mm) × 2 pcs
Speaker
Audio Output
Headphones
Connection Terminals
•
••
•
•
•
•
•
E
N
SD Card Recording
····················· 40, 50
Shipping condition ·· 34
Signal Condition ····· 30
Specifications ········· 55
SRS TruSurround XT
··························· 23
Subtitles ············ 13, 18
S-video ··············· 8, 49
System Update ·· 27, 48
NTSC ················ 20, 55
Specifications
PC signals
Delete file?
DVDs ······················ 19
Index
Specifications
On screen messages (SD Card)
•
Not enough memory
C
Accessories ·············· 6
Add New Service ···· 30
Aspect ·············· 13, 48
Auto Setup ·· 10, 30, 33
AV2/AV3 out ····· 25, 42
• • •
Card recording in progress
Please stop recording to operate
Memory full
Insert a SD card.
Power Display panel
Error
Check card
•
•
•
•
•
•
Broken file
Cannot display image
A
Actions / Meanings
•
•
•
•
•
Index
55
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement