Panasonic SAXR58 Operating instructions

Panasonic SAXR58 Operating instructions
Operating Instructions
AV Control Receiver
Model No. SA-XR58
Dear customer
Thank you for purchasing this product.
Before connecting, operating or adjusting this product,
please read the instructions completely.
Please keep this manual for future reference.
E
SA-XR58.indb 1
RQTV0156-1B
6/27/2006 6:54:34 PM
ENGLISH
Safety precautions
Safety precautions
Placement
Set the unit up on an even surface away from direct sunlight, high
temperatures, high humidity, and excessive vibration. These conditions
can damage the cabinet and other components, thereby shortening the
unit’s service life.
Do not place heavy items on the unit.
Voltage
Do not use high voltage power sources. This can overload the unit and
cause a fire.
Do not use a DC power source. Check the source carefully when
setting the unit up on a ship or other place where DC is used.
AC mains lead protection
Ensure the AC mains lead is connected correctly and not damaged.
Poor connection and lead damage can cause fire or electric shock. Do
not pull, bend, or place heavy items on the lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC mains
lead can cause electric shock.
Do not handle the plug with wet hands. This can cause electric shock.
Foreign matter
Do not let metal objects fall inside the unit. This can cause electric
shock or malfunction.
Do not let liquids get into the unit. This can cause electric shock or
malfunction. If this occurs, immediately disconnect the unit from the
power supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain flammable
gases which can ignite if sprayed into the unit.
Service
Do not attempt to repair this unit by yourself. If sound is interrupted,
indicators fail to light, smoke appears, or any other problem that is
not covered in these operating instructions occurs, disconnect the AC
mains lead and contact your dealer or an authorized service center.
Electric shock or damage to the unit can occur if the unit is repaired,
disassembled or reconstructed by unqualified persons.
Extend operating life by disconnecting the unit from the power source if
it is not to be used for a long time.
CAUTION!
• DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT
RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
• DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS
WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND
SIMILAR ITEMS.
• DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS
LIGHTED CANDLES, ON THE UNIT.
• DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY
FRIENDLY MANNER.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO
RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE
PLACED ON THE APPARATUS.
THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES.
This product may receive radio interference caused by mobile
telephones during use. If such interference is apparent, please
increase separation between the product and the mobile telephone.
The socket outlet shall be installed near the equipment and easily
accessible or the mains plug or an appliance coupler shall remain
readily operable.
CAUTION!
Do not place anything on top of this unit or block the heat radiation
vents in any way. In particular, do not place DVD recorder or CD/
DVD players on this unit as heat radiated from it can damage your
software.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
HDAVI ControlTM is a trademark of Matsushita Electric
Industrial Co., Ltd.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of
Digital Theater Systems, Inc.
Refer to the back cover for
“Supplied accessories”.
2
RQTV0156
SA-XR58.indb 2
6/27/2006 6:54:34 PM
ENGLISH
Table of contents
Using HDAVI ControlTM.............................................. 21
Before use
One-touch Home Theater ................................................. 21
Safety precautions ...................................................... 2
Operations
The remote control .............................................................. 3
Control guide ............................................................... 4
Surround sound......................................................... 22
Remote control/The main unit and display ....................... 4
Connections
Home Theater connections ........................................ 5
Connecting your television and DVD equipment ............. 5
High-quality audio and video simply with HDMI connection .. 5
Connections for high-resolution video (components without
an HDMI)............................................................................. 6
Connections for standard-resolution video (components
without an HDMI) ................................................................ 7
Connection with 21-pin scart cable .................................... 7
6-channel discrete connection (for high-quality DVD-Audio
sound) ................................................................................. 8
Analogue audio connections ............................................... 8
Playing audio from your television through speakers
connected to this unit .......................................................... 9
Connecting a combination DVD recorder/VCR ................... 9
Table of contents
Dolby Pro LogicΙΙx ............................................................ 22
Adjusting the Dolby Pro LogicΙΙx “MUSIC” mode ............ 22
NEO:6 ................................................................................. 23
Adjusting the NEO:6 “MUSIC” mode ............................... 23
SFC (Sound Field Control) ............................................... 24
Adjusting SFC (Sound Field Control) ................................ 25
Receiver settings ....................................................... 26
Basic operations ............................................................... 26
Speaker and size settings/Distance/LR BI-WIRE setting/
Low-pass filter/Auto Setup ................................................ 27
Digital input settings/Input signal/Bi-amp settings............. 28
HDMI settings/Turning the ADVANCED DUAL AMP
off/Clear audio at low volume/Attenuating analogue input/
Delaying audio/Resetting factory settings ......................... 29
Sound effects/Other functions ................................. 30
Basic operations ............................................................... 30
Sound effects-Adjusting the bass/Adjusting the treble/
Adjusting front speaker balance/Adjusting the subwoofer
level................................................................................... 31
Other functions-Selecting audio channels/Adjusting the
dimness of the display/Sleep timer/Muting ....................... 31
Connecting other equipment.................................... 10
Connecting a set top box (cable or satellite)/Connecting a
VCR/Connecting a CD player/Connecting a video camera
or other portable device ................................................... 10
Connecting the antennas and AC mains lead ................ 11
Using headphones ............................................................ 11
The radio .................................................................... 32
Manual tuning .................................................................... 32
Preset tuning ..................................................................... 33
Presetting stations/Selecting channels ............................. 33
Speaker connections ................................................ 12
Connecting speakers ........................................................ 12
Connections and placement to suit the number of speakers
you have ........................................................................... 12
Connecting biwireable speakers/Connecting a second pair
of front speakers ............................................................... 13
RDS broadcasts ......................................................... 34
Changing the display ........................................................ 34
Using the remote control with other equipment..... 34
Television ........................................................................... 34
DVD recorder/DVD player ................................................. 35
VCR/CD player ................................................................... 36
Changing the remote control code/Enter a code to operate
some equipment ............................................................... 37
Before playback ......................................................... 14
Auto speaker setup ........................................................... 14
Process for auto speaker setup ........................................ 14
Troubleshooting for auto speaker setup ........................... 16
Automatic speaker detection ........................................... 17
Speaker output and level .................................................. 17
Reference
Specifications (DIN 45 500)....................................... 38
Help messages .......................................................... 38
Troubleshooting guide.............................................. 39
Supplied accessories ................................. Back cover
Maintenance ................................................ Back cover
Basic operations
Enjoying Home Theater features ............................. 18
Basic play .......................................................................... 18
Digital signals this unit can play/Signal indicators............. 19
Playback options ....................................................... 20
Using SPEAKERS B/ADVANCED DUAL AMP/BI-AMP/
Playing DVD-Audio ........................................................... 20
The remote control
Batteries
Press on the tab to open.
Use
Caution
Sensor
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
HDMI
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
TUNE
SURROUND
AUX
S VIDEO IN VIDEO IN
MENU
SETUP
ENTER
RETURN
AUTO DETECTOR
SETUP MIC
L AUDIO IN R
7 meters (actual distance
depends on the angle)
(R6/LR6, AA)
Insert this side first when closing.
Note
• Insert so the poles (+ and –) match
those in the remote control.
• Do not use rechargeable type
batteries.
• Ensure there are no obstacles
between the remote control and
the main unit.
• Strong light sources (direct
sunlight or strong fluorescent
light) can interfere with
operation.
• Keep the transmitter and sensor
free from dust.
Transmitter
When you set the unit in a
cabinet
Thick or coloured glass can
reduce the operating distance.
3
RQTV0156
SA-XR58.indb 3
6/27/2006 6:54:35 PM
ENGLISH
Control guide
Remote control
1 Power button
Control guide
RECEIVER
1
AV
SYSTEM
TUNER
2
CD
8
RECORDER
DVD
TV
or AM (➡ page 32)
PLAYER
DVD
ANALOG 6CH
VCR
BAND
2 For selecting tuner/ For switching FM
9
3 For selecting stations directly
TUNER (➡ page 32)
For selecting channels
TUNER (➡ page 33)
TV (➡ page 34)
DVD recorder (➡ page 35)
VCR (➡ page 36)
For selecting tracks and chapters
DVD recorder/DVD player (➡ page
35)
For selecting tracks
CD player (➡ page 36)
10
CH
3
VOLUME
11
0
DISC
-/--
DIRECT TUNING
SKIP
SLOW/SEARCH
PAUSE
STOP
DRIVE SELECT
PLAY
DVD RECORDER
MANUAL SKIP
12
TOP
ME
4
ENTER
SUB MENU
5
5 To adjust the subwoofer level
SUBWOOFER
6 For selecting sound modes
TV
DIMMER
LEVEL
EFFECT
NEO : 6
(➡ pages 22, 23, and 24)
VOL
7 For speaker adjustments (➡ page 17)
TV/AV
SFC
MUSIC
MOVIE
AUTO
TEST
switches the source/ switches the
remote control mode
(➡ pages 34 to 37)
9 For switching on the DVD-Audio
6-channel mode (➡ page 20)
10 To change channels
TUNER (➡ page 33)
TV (➡ page 34)
DVD recorder (➡ page 35)
VCR (➡ page 36)
11 Adjusts volume (➡ page 17)
12 For operating other equipment
(➡ pages 21 and 34 to 37)
13 To mute the volume (➡ page 31)
(➡ page 31)
RETURN
OFF
6
4 To dim the display (➡ page 31)
CTIONS
FUN
N
DIRECT NAVIGATO U
R
TOUCH PLAY
ONE
8 Switches on or off other equipment/
7
(➡ pages 14 to 16)
For testing speaker output
(➡ page 17)
For changing sound quality and
sound field (➡ pages 22, 23, and 25)
13
MUTING
14 For auto speaker setup
14
The main unit and display
1 Standby/on switch [8]
Press to switch the unit from on
to standby mode or vice versa.
In standby mode, the unit is still
consuming a small amount of
power.
1
2
3
11
4
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
HDMI
VOLUME
INPUT SELECTOR
SURROUND
MENU
SETUP
ENTER
RETURN
AUTO DETECTOR
AUX
S VIDEO IN VIDEO IN
SETUP MIC
4 Lights when you are using the
L AUDIO IN R
7
12
8
14
10
2CH MIX
16
TUNED
A
20
13
17
18
DIGITAL INPUT
kHz
MHz
21
5 Lights when you are using the bi6 For tuning the radio and selecting
19
cm DTS 96/24DTS-ES
B
indicator lights when you are using
this feature) (➡ page 18)
13 Adjusts volume (➡ pages 11 and
18)
14 For switching input (➡ page 18)
Also used during menu and setup
operation
preset stations (➡ pages 32 to 33)
MONO ST RDS PS PTY M SLEEP
SPEAKERS
BI-WIRE
Advanced Dual Amp (➡ page 20)
amp (➡ page 20)
9
15
8 For switching surround (The
9 For selecting front speakers
(➡ pages 11, 17, 18, and 20)
When the unit is connected to the
AC mains supply, this indicator
10 For connecting other equipment
lights up in standby mode and goes
(➡ pages 10)
out when the unit is turned on.
11 Lights when you are using the
3 Flashes during auto speaker setup.
HDMI connections (➡ page 5)
Lights when the setup finishes
(➡ pages 14 to 16)
12 Headphone jack (➡ page 11)
6
TUNE
(➡ page 14)
2 Standby indicator [^]
5
SPEAKERS
A
B
7 Setup microphone jack
22
DIGITAL EX
23
PCM
EX
15 Lights when multi-channel sources
are being down-mixed to 2
channels
16 Radio indicators
19 Lights when you have set the PCM
FIX mode
20 Shows the front speaker mode you
have selected
17 Sleep timer indicator
21 General display
18 Units for speaker distance and
22 Frequency unit indicators
Bi-amp delay time
23 Digital signal format (➡ page 19)
4
RQTV0156
SA-XR58.indb 4
6/27/2006 6:54:37 PM
Home Theater connections
ENGLISH
• Turn off all components before making any connections.
• Peripheral equipment and cables sold separately unless
otherwise indicated.
• To connect equipment, refer to the appropriate operating
instructions.
Connecting your television and DVD equipment
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
MENU
SETUP
TUNE
SURROUND
ENTER
RETURN
AUTO DETECTOR
AUX
S VIDEO IN VIDEO IN
[HDMI]
HDMI
SETUP MIC
L AUDIO IN R
Home Theater connections
High-quality audio and video simply with HDMI connection
• The HDMI (High Definition Multimedia Interface) connection means you only
need one cable to transmit digital audio and video between two pieces of
equipment. It also carries a command signal that allows you to control your
Panasonic TV (VIERA) or DVD recorder (DIGA) with one touch of a button
(➡ page 21).
• DVD-Audio multi-channel audio is carried as a digital signal. Some DVD
equipment (e.g. with HDMI Ver.1.0) cannot output multi-channel audio as a
digital signal. Use the 6-channel discrete connection (➡ pages 8 and 20) if this
is the case.
• The HDMI indicator lights when you are using this connection.
Connection cable
Video and Audio cable
HDMI Cable
(Use a Panasonic HDMI cable for best results.)
[Recommended part number: RP-CDHG15 (1.5 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m) etc.]
• Use only HDMI cables that have the HDMI logo (as shown on the cover).
To play audio from the television through speakers connected to this unit, ➡ page 9.
TV HDMI
(AV IN)
If you decide to connect a DVD player through
the HDMI, change the “HDMI settings” (➡ page
29).
Rear panel
LOOP
FM ANT
EXT
LOOP ANT
GND
R
��
OUT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
(CD)
BI-WIRE
L
(DVD
RECORDER)��
IN
�DVD������
S VIDEO
R
FRONT B
HF
CENTER
L
SURROUND
R
SURROUND BACK
L
R
L
Note
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
IN
VCR
IN
TV/STB
CENTER
Connect only DVD equipment to the HDMI input
terminal of the unit. Connecting other equipment
may prevent the output of sounds or show distorted
pictures.
SPEAKERS
L
Y
R
PB
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
IN
OUT
TV/STB SUBWOOFER
Y
PB
PR
DVD RECORDER IN
COMPONENT VIDEO
Y
PB
PR
TV / STB IN
In such cases, see “Connecting other equipment”,
➡ page 10, for connections other than HDMI.
DVD HDMI
(AV OUT)
DVD equipment
Audio and video signal flow when you have used HDMI connections
The audio and video signals from DVD equipment pass through to the television even if this unit is set to standby.
When this unit is on
When this unit is in
standby mode
(in standby ON condition,
➡ page 29)
TV
Video
Audio
Audio
TV
Video
Speakers
Speakers
This unit
Video
Audio
Audio
This unit
Video
DVD equipment
Audio
DVD equipment
For your reference
• Audio signals from HDMI connection takes priority to digital terminal connections (➡ page 6 and 7).
• This unit’s HDMI can carry video signals up to 1125i (1080i) (even when this unit is in standby mode).
1125i: an interlace (jump scanning) system that divides 1,125 scan lines in two and sends each half alternately every 1/60
second.
5
RQTV0156
SA-XR58.indb 5
6/27/2006 6:54:39 PM
ENGLISH
Home Theater connections
Connecting your television and DVD equipment (cont.)
Home Theater connections
Connections for high-resolution video (components without an HDMI)
Connection cable
• Check the connections on your equipment and prepare the necessary cables.
• Your equipment will have more than one way of connecting video, so decide which best suits your needs.
Video cable
Audio cable
S-VIDEO connection cable
Optical fibre cable
Connecting the optical fibre cable
Note the shape and fit it
correctly into the terminal.
Do not bend!
Video connection cable
Coaxial cable
To play audio from the television through speakers connected to this unit, ➡ page 9.
TV
S-VIDEO COMPONENT
IN
VIDEO IN
Y
PB
PR
Digital input settings
You can change the input
settings for the digital terminals
if necessary (➡ page 28).
LOOP
FM ANT
EXT
LOOP ANT
GND
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
Rear panel
R
OUT
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
L
SURROUND
R
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
CENTER
SPEAKERS
L
Y
R
PB
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
IN
OUT
TV/STB SUBWOOFER
Y
S-VIDEO
OUT
DVD player
PR
DVD RECORDER IN
COMPONENT VIDEO
Y
DIGITAL
AUDIO OUT
(COAXIAL)
PB
PB
Y
PB
PR
TV / STB IN
PR
DIGITAL S-VIDEO COMPONENT
VIDEO OUT
AUDIO OUT
OUT
(OPTICAL)
DVD recorder
The video terminals
• Connect the video cables in sets so that you have the same type for input and output.
• The component video connection provides the best colour reproduction by separating the luminance (Y) and colour (red: PR or
CR, and blue: PB or CB) signals.
Note
To connect a set top box (cable or satellite), ➡ page 10.
6
RQTV0156
SA-XR58.indb 6
6/27/2006 6:54:41 PM
ENGLISH
• Turn off all components before making any connections.
• Peripheral equipment and cables sold separately unless
otherwise indicated.
• To connect equipment, refer to the appropriate operating
instructions.
Home Theater connections
Connections for standard-resolution video (components without an HDMI)
Connection cable
Video cable
Audio cable
Video connection cable
Optical fibre cable
Connecting the optical fibre cable
Note the shape and fit it
correctly into the terminal.
Scart cable
21-pin scart cable
Do not bend!
Coaxial cable
You will need an adaptor to connect equipment
with a 21-pin scart terminal.
To play audio from the television through speakers connected to this unit, ➡ page 9.
Digital input settings
You can change the input
settings for the digital
terminals if necessary
(➡ page 28).
VIDEO IN
TV
LOOP
FM ANT
EXT
LOOP ANT
GND
R
OUT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
Rear panel
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
SURROUND
L
R
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
CENTER
SPEAKERS
L
Y
R
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
DIGITAL
AUDIO OUT
(OPTICAL)
Y
PB
PR
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
DVD player
VIDEO
DIGITAL
AUDIO OUT OUT
(COAXIAL)
PB
Y
PB
PR
TV / STB IN
DVD recorder
VIDEO
OUT
Note
To connect a set top box (cable or satellite), ➡ page 10.
Connection with 21-pin scart cable
EXT
AV
AM ANT
AV
LOOP ANT
GND
OUT
(DVD RECORDER) IN
VIDEO
S VIDEO
DVD recorder
D)
XIAL2
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
IN
VCR
IN
OUT
TV/STB SUBWOOFER
TV
CENTER
L
AV
R
IN
CD
IN
SUBWOOFER SURROUND FRONT
DVD/DVD 6CH IN DVD RECORDER
AUDIO
Rear panel
DVD player
7
RQTV0156
SA-XR58.indb 7
6/27/2006 6:54:43 PM
ENGLISH
Home Theater connections
Connecting your television and DVD equipment (cont.)
Home Theater connections
Connection cable
Video cable
Audio cable
Video connection cable
Stereo phono cable
White (L)
Red (R)
Optical fibre cable
Connecting the optical digital cable
Note the shape and fit it
correctly into the terminal.
Do not bend!
6-channel discrete connection (for high-quality DVD-Audio sound)
Rear panel
LOOP
FM ANT
EXT
LOOP ANT
GND
R
OUT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
SURROUND
L
R
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
IN
VCR
IN
TV/STB
CENTER
SPEAKERS
L
Y
R
PB
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
DVD equipment
IN
VCR
SUBWOOFER CENTER
PB
PR
Y
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
(R) (L)
FRONT
Y
PB
PR
TV / STB IN
(R) (L)
SURROUND See also “Playing DVD-Audio”,
➡ page 20.
Analogue audio connections
There are some limitations on digital output from DVD equipment, so you may need to make this connection. For video connections,
➡ pages 6 and 7.
Rear panel
LOOP
FM ANT
EXT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
LOOP ANT
GND
R
OUT
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
SURROUND
L
R
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
CENTER
SPEAKERS
L
Y
R
PR
TV MONITOR OUT
IN
CD
DVD player
PB
IN
SUBWOOFER SURROUND FRONT
DVD/DVD 6CH IN DVD RECORDER
AUDIO
(R) (L)
AUDIO
OUT
IN
VCR
IN
OUT
TV/STB SUBWOOFER
(R) (L)
AUDIO
OUT
Y
PB
PR
DVD RECORDER IN
COMPONENT VIDEO
Y
PB
PR
TV / STB IN
DVD recorder
8
RQTV0156
SA-XR58.indb 8
6/27/2006 6:54:45 PM
ENGLISH
• Turn off all components before making any connections.
• Peripheral equipment and cables sold separately unless
otherwise indicated.
• To connect equipment, refer to the appropriate operating
instructions.
Home Theater connections
Playing audio from your television through speakers connected to this unit
Your equipment may be able to output both digital and analogue audio, so decide which best suits your needs.
To take advantage of the multi-channel sounds now available with digital television, use a digital connection. Read your television’s
operating instructions for details.
TV
DIGITAL
AUDIO OUT AUDIO OUT
(OPTICAL) (R) (L)
Rear panel
LOOP
EXT
FM ANT
LOOP ANT
GND
R
OUT
AM ANT
S VIDEO
(TV/STB) (DVD RECORDER) (DVD PLAYER)
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
SURROUND
L
R
SURROUND BACK
L
R
L
(DVD RECORDER) IN
DIGITAL IN
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
CENTER
Digital input settings
You can change the input
settings for the digital terminals
if necessary (➡ page 28).
SPEAKERS
L
Y
R
PB
PR
Y
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
PB
PR
Y
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
PB
PR
TV / STB IN
Connecting a combination DVD recorder/VCR
Digital input settings
You can change the input
settings for the digital terminals
if necessary (➡ page 28).
LOOP
FM ANT
EXT
LOOP ANT
GND
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
Rear panel
R
OUT
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
L
SURROUND
R
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
CENTER
SPEAKERS
L
Y
R
PR
TV MONITOR OUT
IN
CD
Combination DVD
recorder/VCR
PB
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
VIDEO
DIGITAL
AUDIO OUT
OUT
(OPTICAL)
DVD OUT terminals
IN
OUT
TV/STB SUBWOOFER
(R) (L)
AUDIO OUT
Y
PB
PR
DVD RECORDER IN
COMPONENT VIDEO
Y
PB
PR
TV / STB IN
VIDEO
OUT
DVD/VHS COMMON OUT
terminals
For playback instructions,
➡ page 18.
9
RQTV0156
SA-XR58.indb 9
6/27/2006 6:54:47 PM
ENGLISH
Connecting other equipment
Connecting a set top box (cable or satellite)
Connecting other equipment
Your equipment may be able to output both digital and analogue audio, so decide which best suits your needs.
Cable box or satellite receiver etc.
• Connect the video cables in sets so that you have the same type for
input from the equipment and output to your television.
• For television connections, ➡ pages 6 and 7.
LOOP
FM ANT
EXT
LOOP ANT
GND
R
OUT
AM ANT
DIGITAL IN
FRONT A
LF
BI-WIRE
L
R
FRONT B
HF
Rear panel
CENTER
L
S-VIDEO OUT
SURROUND BACK
SURROUND
R
L
R
L
(DVD RECORDER) IN
S VIDEO
VIDEO
VIDEO OUT
(TV/STB) (DVD RECORDER) (DVD PLAYER)
(CD)
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
IN
VCR
IN
TV/STB
CENTER
SPEAKERS
L
Y
R
Digital input settings
You can change the input
settings for the digital
terminals if necessary
(➡ page 28).
PB
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
Y
PB
PR
Y
Y
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
PB
PR
PR
TV / STB IN
COMPONENT
PB VIDEO OUT
Y
(L) AUDIO
(R) OUT
DIGITAL AUDIO
OUT (OPTICAL)
Connecting a VCR
Rear panel
LOOP
FM ANT
EXT
LOOP ANT
GND
R
OUT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
L
SURROUND
R
VCR
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
IN
VCR
VIDEO OUT
IN
TV/STB
(L) AUDIO
(R) OUT
CENTER
SPEAKERS
L
Y
R
PB
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
Y
PB
PR
Y
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
PB
PR
TV / STB IN
Note that you must also use matching connections for your television and DVD recorder, “Connections for standard-resolution video”,
➡ page 7, to view or record the images played on the VCR.
Connecting a CD player
Your equipment may be able to output both digital and analogue audio, so decide which best suits your needs.
LOOP
FM ANT
EXT
LOOP ANT
GND
R
OUT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
(CD)
BI-WIRE
L
R
FRONT B
HF
CENTER
L
CD Player
SURROUND BACK
SURROUND
R
L
R
L
(DVD RECORDER) IN
S VIDEO
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
FRONT A
LF
DIGITAL AUDIO
OUT (COAXIAL)
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
CENTER
Digital input settings
You can change the input
settings for the digital
terminals if necessary
(➡ page 28).
(L) AUDIO
(R) OUT
SPEAKERS
L
Y
R
PB
PR
TV MONITOR OUT
IN
CD
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
IN
OUT
TV/STB SUBWOOFER
Y
PB
PR
Y
DVD RECORDER IN
COMPONENT VIDEO
PB
PR
TV / STB IN
Rear panel
Connecting a video camera or other portable device
Use these terminals for temporary connections.
• Connect the video
cables in sets so that
you have the same
type for input from the
equipment and output
to your television.
• For television
connections, ➡ pages
6 and 7.
S-VIDEO
OUT
VIDEO OUT
ADVANCED
AUTO
SPEAKER SETUP DUAL AMP BI-AMP
HDMI
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
TUNE
SURROUND
AUX
L AUDIO IN R
ENTER
RETURN
AUTO DETECTOR
S VIDEO IN VIDEO IN
MENU
SETUP
(L) AUDIO
(R) OUT
SETUP MIC
Video camera
etc.
10
RQTV0156
SA-XR58.indb 10
6/27/2006 6:54:49 PM
Adhesive tape
2
AM loop antenna (included)
Keep the antenna cord away from
DVD recorders, DVD players, and
other cords.
1
FM ANT
EXT
SURROUND
LOOP ANT
GND
AM ANT
R
3
OUT
DIGITAL IN
FM indoor
antenna
(included)
Fix the other
end of the
antenna
where
reception is
best.
2
1
Rear panel
LOOP
(TV/STB) (DVD RECORDER) (DVD PLAYER)
R
L
VIDEO
Black
Red
(CD)
SURROUND BACK
L
(DVD RECORDER) IN
S VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
Connecting other equipment
Connecting the antennas and AC mains lead
IN
VCR
IN
TV/STB
IN
VCR
IN
OUT
TV/STB SUBWOOFER
CENTER
L
R
IN
CD
FM outdoor antenna
(not included)
• Disconnect the FM
indoor antenna.
• The antenna
should be installed
by a competent
technician.
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
White
ENGLISH
• Turn off all components before making any connections.
• Peripheral equipment and cables sold separately unless
otherwise indicated.
• To connect equipment, refer to the appropriate operating
instructions.
AC mains lead (included)
To household mains socket
FM outdoor
antenna
T
FM AN
Insertion of connector
Even when the connector is perfectly
inserted, depending on the type of inlet
used, the front part of the connector
may jut out as shown in the drawing.
However there is no problem using the
unit.
Appliance inlet
Connector
75 Ω coaxial cable
Approx. 6 mm
Connect AC mains lead after all other cables and cords are connected.
• The included AC mains lead is for use with this unit only. Do not use it with other equipment.
• Do not use an AC mains lead from other equipment.
• If the unit is left unplugged for longer than two weeks, all settings will revert to the factory settings. Perform the settings again if
this occurs.
Using headphones
VOLUME
1.Press [SPEAKERS A] and [SPEAKERS B] to turn
off the speakers.
2.Reduce the volume and connect the headphones.
Plug type: 6.3 mm stereo (in diameter)
3.Adjust the volume.
SPEAKERS
A
B
Note
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
HDMI
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
TUNE
SURROUND
ENTER
RETURN
AUTO DETECTOR
AUX
S VIDEO IN VIDEO IN
MENU
SETUP
SETUP MIC
L AUDIO IN R
• Avoid listening for prolonged periods of time to prevent hearing
damage.
• Turning the speakers off automatically engages stereo play, and
when you play multi-channel sources they are down-mixed (2CH
MIX). (Some DVD-Audio prohibit down-mixing.)
• Note that if you are using DVD 6CH input (➡ page 20), the input
source switches to “DVD” (2 channel) and only the sound for the
front speakers is output.
(Headphone jack)
11
RQTV0156
SA-XR58.indb 11
6/27/2006 6:54:51 PM
ENGLISH
Speaker connections
Connecting speakers
Speaker connections
Connections and placement to suit the number of speakers you have
The ideal is to have all the speakers (except the subwoofer) at equal distances from the seating area.
Auto speaker setup compensates for any differences (➡ pages 14 to 16).
Front speakers (left
, right
)
Place either side of the television, then adjust their position and angle towards the
seating position until you are satisfied with the relationship between the images and
sound.
Center speaker (
)
Place directly above or below the center of the television, aiming at the seating position.
Surround speakers (left
, right
)
Place on either side of or slightly behind the seating area, about one meter higher than
ear level.
Surround back speakers (left
, right
/ when you connect only one
speaker
)
Place behind the seating area, about one meter higher than ear level.
Subwoofer (
)
Place anywhere near the television (but not so close as to cause excessive vibration).
Number of
speakers
7
Placement
• This setup is suitable for playing 6.1-channel sources (DTS-ES and Dolby Digital Surround EX).
• Use Dolby Pro LogicΙΙx, DTS NEO:6, or SFC to enhance 2-channel or 5.1-channel sources.
• This is the best setup for playing 6.1-channel sources (DTS-ES and Dolby Digital Surround EX).
• Use Dolby Pro LogicΙΙx, DTS NEO:6, or SFC to enhance 2-channel or 5.1-channel sources.
6
• Use this setup when you do not have a center speaker.
• The center channel is split between the front speakers.
• This is the best setup for playing 5.1-channel sources (Dolby Digital and DTS materials).
• Use Dolby Pro LogicΙΙx, DTS NEO:6, or SFC to enhance 2-channel sources.
LOOP
FM ANT
EXT
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
5
4
• Any center-channel sound (from 2-channel, 5.1-channel or 6.1-channel sources or allocated
by Dolby Pro LogicΙΙx, DTS NEO:6, or SFC) is split between the front speakers. Surround back
speakers are split between the surround speakers.
3
• Any surround or surround back-channel sound (from multi-channel sources or allocated by
Dolby Pro LogicΙΙx, DTS NEO:6, or SFC) is split between the front speakers.
2
• This is the best setup for stereo sources.
• All other channels are “down-mixed” and played through the front speakers.
12
RQTV0156
SA-XR58.indb 12
(CD)
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
• Use this setup when you do not have a center speaker.
• The center channel is split between the front speakers.
6/27/2006 6:54:54 PM
LOOP ANT
GND
Speaker impedance
Front A: 6 to 16 Ω
Center: 6 to 16 Ω
Surround: 6 to 16 Ω
Surround back: 6 to 16 Ω
If you have a single surround back speaker,
connect it to the SURROUND BACK (L)
terminal .
2
3
4
5
6
7
8
n.
1
R
UT
FRONT A
LF
BI-WIRE
L
FRONT B
HF
R
CENTER
SURROUND
L
R
SURROUND BACK
L
R
Speaker cable
2
Front speaker (R)
3
Front speaker (L)
4
Center speaker
5
Surround speaker (R)
6
Surround speaker (L)
7
Surround back speaker (R)
8
Surround back speaker (L)
9
Monaural connection cable
ENGLISH
L
10 Active subwoofer
(DVD RECORDER) IN
S VIDEO
VIDEO
IN
IN
IN
OUT
IN
IN
OR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
CENTER
L
IN
VCR
IN
TV/STB
10
Note
SPEAKERS
Y
R
PB
PR
Y
TV MONITOR OUT
IN
CD
1
Speaker connections
• Turn off all components before making any connections.
• Peripheral equipment and cables sold separately unless
otherwise indicated.
• To connect equipment, refer to the appropriate operating
instructions.
SUBWOOFER SURROUND FRONT
IN
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
PB
PR
Y
PB
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
PR
TV / STB IN
9
Rear panel
After changing your speaker set up:
Perform auto speaker setup
(➡ pages 14 to 16) or automatic speaker
detection (➡ page 17); or for manual
settings (➡ page 27).
Connecting biwireable speakers
Biwireable speakers have separate terminals for the high frequency and low frequency
signals.
• Use this connection to reduce interference between the high frequency and low frequency
signals for high-fidelity sound.
• When you are playing analogue or 2-channel PCM sources, the unit can allocate an amplifier
each to the high frequency and low frequency signals, thereby giving you a much clearer biamp stereo sound (➡ page 20).
• HF stands for high frequency and LF for low frequency.
Speaker impedance
BI-WIRE: 6 to 16 Ω
LOOP
EXT
AM ANT
DIGITAL IN
ORDER) (DVD PLAYER)
LOOP ANT
GND
Front speaker
(R)
Rear view
OUT
(CD)
HF
R
FRONT A
LF
BI-WIRE
L
R
FRONT B
HF
CENTER
L
SURROUND
R
HF
SURROUND BACK
L
R
L
(DVD RECORDER) IN
S VIDEO
CAL2 COAXIAL1 COAXIAL2
Rear panel
VIDEO
OUT
IN
IN
IN
OUT
IN
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER DVD RECORDER
IN
VCR
For your reference
• Be sure to connect the HF cables
to the FRONT B terminals, and
the LF cables to the FRONT A
terminals, so that you can correct
any delay that may occur
(➡ page 28).
• To take advantage of this
connection and ensure the
best possible sound, be sure
Front speaker to change the setting in “LR BIWIRE setting” to “YES”
(L)
(➡ page 27).
Rear view
IN
TV/STB
CENTER
SPEAKERS
LF
L
Y
R
PR
Y
TV MONITOR OUT
Speaker cable
IN
CD
PB
IN
SUBWOOFER SURROUND FRONT
DVD/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
PB
PR
Y
DVD RECORDER IN
COMPONENT VIDEO
IN
OUT
TV/STB SUBWOOFER
PB
LF
PR
TV / STB IN
Connecting a second pair of front speakers
This second set of terminals allows you to connect a second pair of speakers to place in
another room, for example.
To use the speakers connected to the FRONT B terminals, press [SPEAKERS B] (➡ page 20).
Speaker cable
Rear panel
R
FRONT A
LF
BI-WIRE
L
R
FRONT B
HF
CENTER
L
SURROUND
R
Note
SURROUND BACK
L
R
L
) IN
VIDEO
IN
IN
OR DVD PLAYER DVD RECORDER
IN
VCR
IN
TV/STB
Front speaker (R)
SPEAKERS
Y
PB
PR
TV MONITOR OUT
IN
ND FRONT
/DVD 6CH IN DVD RECORDER
AUDIO
IN
VCR
IN
OUT
TV/STB SUBWOOFER
Y
PB
PR
DVD RECORDER IN
COMPONENT VIDEO
Y
PB
PR
Speaker impedance
Front A and B: 6 to 16 Ω
Front B: 6 to 16 Ω
Front speaker (L)
When only SPEAKERS B is on, output
will be 2-channel only. Signals from
multi-channel sources are “downmixed” and output through the two front
speakers you have connected.
TV / STB IN
13
RQTV0156
SA-XR58.indb 13
6/27/2006 6:54:56 PM
ENGLISH
Before playback
Before playback
Auto speaker setup
Auto speaker setup allows you to achieve a satisfactory listening environment easily with the use of the supplied calibration
microphone as a detector of sound signals. The unit will first perform automatic speaker detection, then checks and adjusts the
following settings.
Automatic speaker detection
(This can also be performed in
“Automatic speaker detection”,
➡ page 17. However, for a
more optimized listening
environment, carry out the
setup here.)
• Checks which speakers you have connected.
• The factory setting is 7 speakers and a subwoofer.
• Some types of speakers and cables may cause disruptions to the setup. In this case, conduct
manual setting, “Speaker and size settings”, ➡ page 27.
DISTANCE
• Checks the distance of each speaker from the listening position and adjusts the timing of each
channel. For manual setup, “Distance”, ➡ page 27.
POLARITY
• Checks the polarity of each speaker. You can choose not to have polarity checked, “Auto
setup”, ➡ page 27.
SIZE
FREQUENCY
LEVEL
• Checks the speaker’s frequency response. For manual setup, “Speaker and size settings”,
➡ page 27.
• The front speakers are set to SMALL if the unit determines that they are different sizes.
• Sets the appropriate low frequency crossover for each channel according to the speaker size.
For manual setup, “Low-pass filter”, ➡ page 27.
• The setting is based on the speaker with the lowest bass reproduction range.
• Also checks on “Level” setting to adjust the sound level (volume) for each speaker.
• Makes any further corrections to the volume of each speaker (for manual setup, “Speaker output
and level” ➡ page 17) and also to the frequency response.
Before setup
• Conduct the auto speaker setup in a quiet environment. A noisy background will give unsatisfactory results.
• Put the subwoofer in position, switch it on, and sets its volume to the level you would normally use. If you do auto speaker setup
without the subwoofer, the front speakers will be set as large, possibly resulting in an unsatisfactory bass.
Process for auto speaker setup
1 Placing of calibration microphone.
Place on a flat surface at the seating area. Use a tripod for best results.
2
Connect the calibration microphone to the [SETUP
MIC] jack on the front panel.
ADVANCED
AUTO
SPEAKER SETUP DUAL AMP BI-AMP
Note
The calibration microphone is sensitive to heat. Keep it away from direct
sunlight and do not place it on top of the unit.
SPEAKERS
A
B
TUNE
SURROUND
AUTO DETECTOR
AUX
S VIDEO IN VIDEO IN
SETUP MIC
L AUDIO IN R
14
RQTV0156
SA-XR58.indb 14
6/27/2006 6:54:58 PM
SYSTEM
RECORDER
DVD
TV
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
• Turn off all components before making any connections.
• Peripheral equipment and cables sold separately unless
otherwise indicated.
VOLUME
• To connect equipment, refer to the appropriate
DISC
0 operating
-/-DIRECT TUNING
instructions.
SLOW/SEARCH
SKIP
STOP
PAUSE
DRIVE SELECT
AUTO
SPEAKER SETUP
ENTER
SUB MENU
Press
SUBWOOFER
OFF
• The standby indicator goes off when you turn on the unit.
RETURN
LEVEL
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
DIMMER
EFFECT
NEO : 6
SPEAKERS
A
B
TV/AV
SFC
TUNE
SURROUND
MUSIC
TV
VOL
MOVIE
AUTO
TEST
MUTING
AUTO DETECTOR
AUX
AUTO
a) Press and hold TEST for about 2 seconds.
• [AUTO SPEAKER SETUP] indicator starts flashing.
AUTO
SPEAKER SETUP
S VIDEO IN VIDEO IN
SETUP MIC
Before playback
TOP
ME
N
DIRECT NAVIGATO U
R
Turn on the unit.
MANUAL SKIP
TOUCH PLAY
ONE
CTIONS
FUN
3 Start performing auto speaker setup.
PLAY
DVD RECORDER
ENGLISH
TUNER
L AUDIO IN R
AUTO
SPEAKER SETUP
• “AUTO SETUP” appears on the display.
b) The unit checks that you have correctly connected the
calibration microphone.
c) The automatic setup starts the automatic speaker detection,
STEP 1, STEP 2, and STEP 3 calibration as follows.
(Automatic speaker
detection)
↓
STEP1 L→STEP1 C→STEP1 R→STEP1 RS→STEP1 SBR
→STEP1 SBL→STEP1 LS→STEP1 SUBW→PROCESSING
↓
Speaker abbreviations
L: Front left
C: Center
R: Front right
S: Surround
RS: Surround right
LS: Surround left
SB: Surround
back
SBR: Surround back
right
SBL: Surround back
left
W/SUBW: Subwoofer
For your reference
STEP2 L→STEP2 C→STEP2 R→STEP2 RS→STEP2 SBR
→STEP2 SBL→STEP2 LS→STEP2 SUBW→PROCESSING
↓
• Loud test tones are output from each speaker during the
configuration.
• The checked settings display for a minimum of 3 seconds
each.
STEP3 L→STEP3 C→STEP3 R→STEP3 RS→STEP3 SBR
→STEP3 SBL→STEP3 LS→STEP3 SUBW→PROCESSING
During setup, operations may stop when there is an error message on the display. Refer to page 16 for
troubleshooting.
4
Auto speaker setup finishes.
• “COMPLETE” appears on the display and all calibrations are saved.
• [AUTO SPEAKER SETUP] indicator lights.
AUTO
• To exit, press TEST .
• Disconnect the calibration microphone.
To cancel during setup
Press any button on the main unit or remote control. “CANCELED” appears on the display.
Note
Perform auto speaker setup again if you have changed the speakers, speaker positions, or the layout of your listening environment.
15
RQTV0156
SA-XR58.indb 15
6/27/2006 6:55:00 PM
ENGLISH
Before playback
Auto speaker setup
RECEIVER
AV
SYSTEM
RECORDER
DVD
Before playback
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
VOLUME
0
DISC
-/--
DIRECT TUNING
SKIP
SLOW/SEARCH
PAUSE
STOP
DRIVE SELECT
PLAY
DVD RECORDER
MANUAL SKIP
TOP
ME
SPEAKERS
A
B
SUB MENU
AUTO DETECTOR
AUTO
SPEAKER SETUP
ENTER
RETURN
SUBWOOFER
OFF
]
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
TUNE
SURROUND
VOLUME
TV/AV
SFC
MUSIC
VOL
MOVIE
AUTO
TEST
MUTING
ENTER
RETURN
AUTO DETECTOR
AUX
S VIDEO IN VIDEO IN
MENU
SETUP
EFFECT
NEO : 6
HDMI
INPUT SELECTOR
SPEAKERS
A
B
TV
DIMMER
LEVEL
[
CTIONS
FUN
N
DIRECT NAVIGATO U
R
TOUCH PLAY
ONE
SETUP MIC
L AUDIO IN R
While performing auto speaker setup, errors may occur and the messages will blink or scroll on the display, depending on the
conditions. Press any button on the main unit or remote control to stop the setup.
AUTO
After troubleshooting, press and hold TEST for 2 seconds to start the setup process again.
Troubleshooting for auto speaker setup
Message
Solutions
Pages
“INSERT MIC”
• Calibration microphone is not detected. Insert the microphone correctly.
14
“NO SIGNAL”
• Check that the calibration microphone is connected correctly.
14
“DISTANCE ERROR”
• Bring the speakers nearer to the calibration microphone.
-
“NOISY”
• Setup in a quiet environment or do auto speaker setup at a quieter time of day.
• Turn off equipment that may produce noise, such as air conditioners.
-
“MEASURING ERROR”
• Change the positions of the speakers and perform the setup again.
-
“CHECK CONNECTION
TO SBL SPEAKER”
• Left surround back speaker not detected. If you have decided to use only one
surround back speaker, connect it to the SURROUND BACK (L) terminal.
• Check connection to left surround back speaker.
13
“NEED TO CONNECT
LS/RS SPEAKERS”
• Surround speakers not detected. You must have surround speakers connected
before you can connect and use surround back speakers effectively.
13
“CHECK
CONNECTIONS TO
LS/RS SPEAKERS”
• One or both surround speakers not detected. Check the connections.
13
“CHECK
CONNECTIONS TO L/R
SPEAKERS”
• Check the front (L) and (R) connections.
13
“LOW SIGNAL”
• Change the position (height and direction) of the microphone.
• Make sure there is nothing around the microphone that could interfere with the test
tones.
• Make sure the volume of the subwoofer is set to the level you would normally use.
13
17
Note
•
•
•
•
16
Auto speaker setup may produce an unsatisfactory result with some speaker setups and configurations.
You can perform auto speaker setup even if SPEAKERS A are off.
For subwoofer, only level is adjusted in auto speaker setup.
All settings in auto speaker setup return to the factory setting if you do automatic speaker detection (➡ page 17) separately, or,
change the speaker size (except for front speakers) from “NO” or “NONE” to other size settings (“Speaker and size settings”,
➡ page 27).
• Auto speaker setup will not start if you have muted the speakers. Turn the muting off (➡ page 31).
• HDAVI ControlTM (➡ page 21) is disabled during auto speaker setup.
RQTV0156
SA-XR58.indb 16
6/27/2006 6:55:01 PM
Automatic speaker detection is performed during auto speaker setup. Do the following only if you want to check speakers’ status, and
not other settings.
Turn on the unit.
Before playback
1
Press
• The standby indicator goes off when you turn on the unit.
2
ENGLISH
Automatic speaker detection
Start automatic speaker detection.
Press
SPEAKERS
A
B
at the same time.
(Checks each speaker’s
connection status)
(Shows the number of detected
speakers, excluding the subwoofer)
↓
↓
↓
AUTO DETECTOR
(Shows connected speakers)
(Automatic speaker detection ends.
The previous display reappears)
• These settings are saved even if you turn the unit off.
• Refer to page 14 for further notes and page 16 for error message explanations. (“WARNING” may appears on the display during
the detection here.)
Speaker output and level
Adjust the level of the speakers so they are the same apparent level as the front speakers from the seating area.
Speaker level is adjusted during auto speaker setup. Do the following only if you find the level unsatisfactory.
1
To turn on SPEAKERS A.
Press
SPEAKERS A are on
SPEAKERS
A
SPEAKERS
A
If you have bi-wired your front speakers (➡ page
13), make sure you have selected “YES” for the
“LR BI-WIRE setting” (➡ page 27).
SPEAKERS
A
Press
2
Press
SPEAKERS
B
or
AUTO
TEST
SPEAKERS A and B are on
SPEAKERS
or
A
B
• The unit does not output the test signal if only SPEAKERS B is
on.
SPEAKERS
BI-WIRE
A
B
to output the test signal.
• The signal is output from each speaker in order for
about two seconds each:
L→C→R→RS→SBR→SBL→LS→SUBW
or L→C→R→RS→SB1→LS→SUBW
1
If you connect one surround back speaker only (the left
surround back speaker)
Speaker abbreviations
L: Front left
C: Center
R: Front right
RS: Surround right
LS: Surround left
SBR: Surround back right
SBL: Surround back left
SB: Surround back (If you connect
one surround back speaker)
SUBW: Subwoofer
Make sure your speaker settings match your connections (➡ pages 13, and 14 to 16). There will be no output from a speaker if
it is set as NO or NONE (➡ page 27).
3
Set speakers volume to the level you would normally use.
Press
Volume range:
-- dB (minimum), -79 dB to 0 dB (maximum)
VOLUME
LEVEL
4
Press
5
Press
to adjust the level
to the same apparent level as the
front speakers.
to select the speaker channel to adjust.
Repeat steps 4 and 5 for each speaker channel.
Adjustment range:
-20 dB to +10 dB (Factory setting: 0 dB )
For the subwoofer (SUBW)
MIN (minimum) ↔ 1 to 29 ↔ MAX (maximum)
(Factory setting: 20 )
The test signal is output only from the speaker you are adjusting in
steps 4 and 5. Test signal for connected speakers resumes after 2
seconds.
6
Press
AUTO
TEST
to stop the test signal.
17
RQTV0156
SA-XR58.indb 17
6/27/2006 6:55:04 PM
ENGLISH
Enjoying Home Theater features
Basic play
SURROUND
SPEAKERS
A
B
INPUT SELECTOR
Enjoying Home Theater features
VOLUME
[
]
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
HDMI
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
MENU
SETUP
TUNE
SURROUND
AUX
S VIDEO IN VIDEO IN
1
ENTER
RETURN
AUTO DETECTOR
SETUP MIC
L AUDIO IN R
Turn on the unit.
Note
Press
• The standby indicator goes off when you turn on the unit.
Before using the unit for the first time or after changing your speaker
set up, make sure that you perform auto speaker setup
(➡ pages 14 to 16) or automatic speaker detection (➡ page 17), or for
manual settings (➡ page 27).
The [SURROUND] indicator lights to show that the
surround mode is on (factory setting).
SURROUND
2
Turn on SPEAKERS A.
Press
SPEAKERS
A
SPEAKERS
If you also want to use SPEAKERS B, press [SPEAKERS B] to
turn them on. (Remember that sound will only be stereo if you
use just SPEAKERS B.)
A
If you have bi-wired your front speakers (➡ page 13),
make sure you have selected “YES” for the “LR BIWIRE setting” (➡ page 27).
SPEAKERS
A
Press
SPEAKERS
B
or
SPEAKERS
BI-WIRE
A
B
INPUT SELECTOR
3
Turn
to select the input source.
If you have a combination DVD recorder/VCR
(➡ page 9)
• Select “DVR” to watch DVDs.
• Select “VCR” to watch video tapes.
4
Start playing the source
If you would prefer to listen in stereo, press
[SURROUND] to turn the indicator off.
To return to surround sound, press [SURROUND] to turn
the indicator on.
5
Adjust the volume.
VOLUME
Input sources:
TUNER FM, TUNER AM, CD, TV/STB, DVD, DVR (DVD
recorder), VCR (video recorder), AUX (front terminals)
• “DVD RECORDER” scrolls once across the display if you
select “DVR”.
• You can also select the input source with the buttons on the
remote control (➡ pages 34 to 36).
• The unit stores whether you have selected SURROUND
or not for each input source, but the mode automatically
activates if you play a multi-channel source.
• You can “down mix” multi-channel sources to 2 channels by
pressing [SURROUND] to turn the indicator off during play.
(Some DVD-Audio prohibit down-mixing.)
2-channel down-mix cancels when you turn the unit off or
change the input source.
Volume range:
-- dB (minimum), -79 dB to 0 dB (maximum)
Turn
When you finish listening
Be sure to reduce the volume and press [8] to switch the unit to standby.
18
RQTV0156
SA-XR58.indb 18
6/27/2006 6:55:06 PM
ENGLISH
Dolby Digital (including
Dolby Digital Surround
EX)
These digital surround systems were developed by Dolby Laboratories. Dolby
Digital Surround EX, with its additional surround back channels, produces an
increased sense of realism.
DTS (including DTS-ES
and DTS 96/24)
These digital surround systems were developed by DTS (Digital Theater
Systems, Inc.). DTS-ES, with its additional surround back channel, immerses
you in sound. DTS 96/24 delivers multi-channel sound with superior fidelity (96
kHz/24 bit).
PCM
You can input PCM signals with sampling frequencies up to 192 kHz with the
DIGITAL IN COAXIAL 1 terminal. The other digital terminals allow input of up to
96 kHz. The display shows the sampling frequency when you input 88.2-kHz,
96-kHz, 176.4-kHz, or 192-kHz signals.
DVD etc.
DVD etc.
CD, DVDAudio etc.
Note
This unit cannot process Dolby Digital RF or MPEG audio signal.
Signal indicators
2CH MIX
TUNED
MONO ST RDS PS PTY M SLEEP
DIGITAL INPUT
cm DTS 96/24DTS-ES
SPEAKERS
BI-WIRE
A
B
kHz
MHz
PCM
DIGITAL EX EX
PLⅡx NEO:6 SFC
DIGITAL:
Dolby Digital sources
DTS:
DTS sources
DIGITAL EX:
Dolby Digital Surround EX decoder (while in Dolby Pro
LogicΙΙx mode) when the input signal is Dolby Digital 5.1channel or Dolby Digital Surround EX and you are using one
surround back speaker.
DTS 96/24:
DTS 96/24 sources
EX:
Dolby Digital Surround EX decoder (while in Dolby Pro
LogicΙΙx mode) when the input signal is DTS 5.1-channel and
you are using one surround back speaker.
DTS-ES:
DTS-ES Discrete 6.1 sources or when using
the DTS-ES matrix
PLΙΙx:
Dolby Pro LogicΙΙx decoder
NEO:6:
DTS NEO:6 matrix
PLΙΙ:
Dolby Pro LogicΙΙ with stereo sources when you are not
using a surround back speaker.
SFC:
Sound field control
Enjoying Home Theater features
Digital signals this unit can play
For your reference
• Dolby Pro LogicΙΙx, NEO:6, and SFC add surround effects by “adding” channels, so if they are off, the unit plays the number of channels recorded in
the original source.
For example, if it is a 5.1-channel source, there will be no output from the surround back speakers.
• The SURROUND mode turns off when input is 192-kHz PCM.
• Whenever you switch to a different source, the following display appears to show you the number of channels. (It may not appear with some
sources.)
Subwoofer
Surround and surround back channels
Front and center channels
19
RQTV0156
SA-XR58.indb 19
6/27/2006 6:55:07 PM
ENGLISH
Playback options
ADVANCED
DUAL AMP [BI-AMP]
RECEIVER
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
SPEAKERS
B
TV
HDMI
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
AUX
TUNER
ENTER
CD
RETURN
AUTO DETECTOR
S VIDEO IN VIDEO IN
MENU
SETUP
TUNE
SURROUND
VCR
BAND
RECORDER
DVD
PLAYER
DVD
ANALOG 6CH
SETUP MIC
L AUDIO IN R
CH
To use the speakers
connected to the FRONT B
terminals.
SPEAKERS
B
Press
ADVANCED
DUAL AMP
BI-AMP
The Advanced Dual Amp activates automatically. In stereo sources or
in 5.1 channel, the unused surround back speakers amplifiers drive the
ENTER
front speakers for a clearer, purer sound.
SUB MENU
The bi-amp activates if you
have bi-wired your front
speakers and play analogue or
stereo PCM sources.
The amplifiers for the front and
surround speakers separately
run the low frequency and high
frequency. You can use this
feature in combination with the
Advanced Dual Amp (➡ above)
for an even clearer and purer
stereo sound.
Digital
DVD analogue 6CH
SUBWOOFER
OFF
DIMMER
(➡ below).
Connect your DVD equipment with an HDMI cable (➡ page 5) or with a
coaxial cable through the DIGITAL IN COAXIAL 1 terminal (➡ pages 6
and 7).
• Connect through the DVD 6CH IN
terminals (➡ page 8).
• Switch on SPEAKERS A or BI-WIRE.
• Select “DVD” as input (➡ page 18).
PLAYER
DVD
Press and hold
until
ANALOG 6CH
“DVD 6CH” appears on the display.
• To cancel, press and hold until
“DVD” appears on the display.
2-channel analogue
• [ADVANCED DUAL AMP]
lights when the function is
on.
• RETURN
You can turn this function off
(➡ page 29).
• [BI-AMP]
lights when the
TV
function is on.
VOL
LEVEL EFFECT • To make bi-amp settings
• Bi-wire your front speakers (➡ page
13).
(➡ page 28).
NEO : 6
TV/AV
• Make sure you have selected
“YES”
for the “LR BI-WIRE setting” (SFC
➡ page AUTO
Note
27).
MUSIC
MOVIE
MUTING
TEST
You cannot use the bi-amp if you
• Turn the SURROUND mode off
are using DVD 6CH input
(➡ page 18).
Preparation
Preparation
Playing DVDAudio
NCTIONS
�FU
TOP
ME
Using
SPEAKERS B
• Sound will be stereo from SPEAKERS B.
• If you have only SPEAKERS B on and the input signal is multiVOLUME
channel, the signal is down-mixed and “2CH
MIX” appears on the
DISC
display.
0
-/-DIRECT TUNING
• To turn off sound from SPEAKERS
A, press
[SPEAKERS A] so “ A ”
goes off.
SKIP6CH input
SLOW/SEARCH
• Note that if you are using DVD
(below), only the sound for
STOP PAUSE
PLAY
the front speakers is output.
• Speaker settings (➡ page 27) are fixed as follows when you have only
MANUAL SKIP
DRIVE SELECT DVD RECORDER
SPEAKERS B on.
Speaker size: LARGE
C
U
H
O
T
P
LAY
NE
Subwoofer: NO (bass is outputOfrom the front speakers.)
NU
�DIRECT NAVIGATOR
Playback options
A
AV
SYSTEM
This mode lets you enjoy the highquality stereo sound available with
DVD-Audio recorded with a sampling
frequency of 192 kHz.
If you are using a DVD
recorder
You cannot switch to DVD
6CH input if “DVR” is the
input source, so connect your
recorder through the DVD 6CH
IN terminals and select “DVD”
as the input source if you want
to listen to DVD-Audio.
Note
“Level” settings (➡ pages 14 and
17) made on this unit, except for
subwoofer level, are ineffective.
1. Cancel “DVD 6CH” if
necessary (➡ above).
2. In INPUT MODE, fix input to
analogue (➡ page 28).
20
RQTV0156
SA-XR58.indb 20
6/27/2006 6:55:09 PM
Preparation
1. Connect your other Panasonic home theater equipment (HDAVI Control compatible VIERA television or DIGA DVD
recorder) with an HDMI cable (➡ page 5).
(Cables that do not meet the HDMI specifications are not compatible with this feature. Use a Panasonic HDMI cable for best
results.)
2. Read your television’s operating instructions and make the settings necessary to activate the HDAVI Control.
3. Switch on all your equipment, then switch your television off then on again and check that images from DIGA appear
correctly.
(Do this whenever you change connections or settings.)
Rear panel
TV HDMI
(AV IN)
TV (VIERA)
LOOP
DIGITAL AUDIO
OUT (OPTICAL)
FM ANT
EXT
LOOP ANT
GND
AM ANT
DIGITAL IN
(TV/STB) (DVD RECORDER) (DVD PLAYER)
OUT
DVD HDMI
(AV OUT)
DVD recorder
(DIGA)
(DVD RECORDER) IN
S VIDEO
(CD)
OPTICAL1 OPTICAL2 COAXIAL1 COAXIAL2
ENGLISH
HDAVI Control
This convenient feature links control of your receiver and your other Panasonic home theater equipment. VIERA televisions and
DIGA DVD recorders connected with an HDMI cable can be controlled in this way. For details, refer to the operating instructions of
your other equipment.
Using HDAVI ControlTM
Using HDAVI ControlTM
OUT
IN
IN
IN
OUT
IN
TV MONITOR DVD PLAYER DVD RECORDER TV/STB TV MONITOR DVD PLAYER
• To take advantage of the multi-channel sounds now available with digital television, use a digital connection if your TV has a digital output terminal.
RECEIVER
AV
SYSTEM
RECORDER Theater
One-touch
Home
TV
DVD
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
VOLUME
0
DISC
-/--
DIRECT TUNING
SKIP
STOP
DRIVE SELECT
Point the remote control at your DIGA DVD recorder and press [ONE
TOUCH PLAY].
1. Your DIGA switches on. Play starts if there is a disc in the tray. If a disc is not in the tray, DIGA
plays the television program last recorded to the hard disk.
2. Your VIERA switches on and input switches.
3. This unit switches on, input switches to “DVR”, and multi-channel play starts.
Press [+ VOLUME -] to adjust the volume.
You can also adjust the volume with VIERA’s remote control.
(An indicator appears on the television showing that you are adjusting this unit’s volume.)
If the beginning of the program is cut off, press [u SKIP] to skip back to the beginning.
SLOW/SEARCH
PAUSE
PLAY
DVD RECORDER
MANUAL SKIP
TOUCH PLAY
ONE
TOP
ME
ENTER
NCTIONS
�FU
NU
�DIRECT NAVIGATOR
TOUCH PLAY
ONE
For your reference
• If you switch your VIERA off, this unit also switches off (unless you have changed the input source to
“TUNER” or “CD”).
• VIERA’s speakers start to output the audio instead if you switch this unit off. If you then switch this unit on
again, audio output switches back to this unit.
• If this unit is off and you switch the setting on your VIERA so that audio is output from a connected receiver,
this unit switches on and starts to output the audio.
Multi-channel
audio for
your VIERA
SUB MENU
RETURN
• Connect your VIERA’s digital output terminal to the DIGITAL IN OPTICAL 1 terminal on this unit (➡ page 9).
• Refer to your VIERA’s operating instructions and make the settings necessary to switch audio output from VIERA’s speakers to
SUBWOOFER
TV
speakers
to this unit.
OFF connected
DIMMER
VOL
• The input LEVEL
source
on
this
unit switches to “TV” if you select a channel or otherwise operate the television (➡ page 34).
EFFECT
:6
TV/AV
To turnNEOoff
HDAVI Control,
“HDMI settings”, ➡ page 29.
SFC
MUSIC
MOVIE
AUTO
TEST
MUTING
21
RQTV0156
SA-XR58.indb 21
6/27/2006 6:55:11 PM
ENGLISH
Surround sound
Surround sound
There are various modes you can use to add surround effects or play stereo through more than just the normal two speakers.
Dolby Pro LogicΙΙx
RECEIVER
AV
SYSTEM
RECORDER
DVD
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
• This feature adds surround effects to stereo sources.
• It can also expand 5.1-channel Dolby Digital and DTS so that you can hear them through 7.1
channels (when you have connected 2 surround back speakers) or 6.1 channels (when you
have connected 1 surround back speaker).
• Use this mode when playing Dolby Digital Surround EX to make effective use of the
surround back channel.
Press
to select one of the following modes.
VOLUME
(Movie)
0
DISC
-/--
DIRECT TUNING
Use this mode when playing movie software, especially if it is recorded in
Dolby Surround.
If you have connected two surround back speakers, their output will be in
stereo.
This is the factory setting.
This mode is effective on music sources.
SKIP
STOP
SLOW/SEARCH
PAUSE
DRIVE SELECT
PLAY
DVD RECORDER
MANUAL SKIP
(Dolby Digital EX)
TOP
ME
SUB MENU
RETURN
(Game)
TV
SUBWOOFER
DIMMER
OFF
LEVEL
EFFECT
NEO : 6
VOL
TV/AV
SFC
MUSIC
NCTIONS
�FU
NU
�DIRECT NAVIGATOR
TOUCH PLAY
ONE
ENTER
(Music)
MOVIE
AUTO
TEST
MUTING
Use this mode when playing movie software, especially if it is recorded in
Dolby Digital EX format.
It is effective on multi-channel sources.
If you have connected two surround back speakers, output from them will
be monaural.
• If you have connected one surround back speaker, the “ PLΙΙx”
indicator goes out and either “ DIGITAL EX” or “ EX” lights instead.
Enjoy gaming with more impact.
This mode is effective on stereo sources.
You cannot use this mode unless you have connected both surround
speakers and surround back speakers (➡ pages 13 and 14 to 17). Make
sure you have also set these speakers as present in “Speaker and size
settings” (➡ page 27).
To cancel, press OFF
Adjusting the Dolby Pro LogicΙΙx “MUSIC” mode
You can make the following adjustments in stereo sources.
Note
(Dimension Control)
You can make up for differences in the output level of the front and
surround speakers.
EFFECT
Press
to select “DIMEN”, then press
adjust the level.
to
Adjustment range: -3 (emphasis on the surround speakers) to +3
(emphasis on the front speakers)
Factory setting: 0
• You may be unable to use
some of these surround
effects with some sources.
• These settings are saved
even if you turn the unit off.
(Center Width Control)
This is an overall adjustment for the front and center speakers to achieve a
more natural sound.
EFFECT
Press
to select “C-WIDTH”, then press
adjust the level.
to
Adjustment range: 0 (for a distinct center) to 7 (for a broad center)
Factory setting: 3
(Panorama)
This mode spreads sound out to envelope you in music.
EFFECT
Press
to select “PANORAMA”, then press
to select “ON” or “OFF”.
Factory setting: OFF
22
RQTV0156
SA-XR58.indb 22
6/27/2006 6:55:14 PM
RECEIVER
AV
SYSTEM
RECORDER
DVD
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
ENGLISH
• This feature adds surround effects to stereo sources.
• It can also expand 5.1-channel Dolby Digital and DTS so that you can hear them through 6.1
channels.
Press
NEO : 6
to select one of the following modes.
CH
Use this mode when playing movies.
(Cinema)
This mode is effective on music sources.
VOLUME
0
DISC
SKIP
STOP
SLOW/SEARCH
PAUSE
DRIVE SELECT
(Music)
-/--
DIRECT TUNING
PLAY
DVD RECORDER
TOP
ME
NU
�DIRECT NAVIGATOR
RETURN
TV
SUBWOOFER
To cancel, press OFF
Adjusting the NEO:6 “MUSIC” mode
NCTIONS
�FU
SUB MENU
For 2-channel Dolby Digital and DTS sources with matrix-encoded multi-channel audio, use
“CINEMA”. For simple stereo sources, use “MUSIC”.
MANUAL SKIP
TOUCH PLAY
ONE
ENTER
Surround sound
NEO:6
(Center Image
Control)
This is an overall adjustment for the front and center speakers to achieve a
more natural sound.
EFFECT
Press
to select “C-IMAGE”, then press
adjust the level.
to
Adjustment range: 0 (for a distinct center) to 5 (for a broad center)
Factory setting: 2
DIMMER
OFF
LEVEL
EFFECT
NEO : 6
VOL
TV/AV
SFC
MUSIC
MOVIE
AUTO
TEST
MUTING
Note
• There will be no output from
the subwoofer when using
NEO:6 on stereo sources
and you have set all of your
speakers to “LARGE” in
“Speaker and size settings”
(➡ page 27).
• You may be unable to use
some of these surround
effects with some sources.
• These settings are saved
even if you turn the unit off.
23
RQTV0156
SA-XR58.indb 23
6/27/2006 6:55:15 PM
ENGLISH
Surround sound
Surround sound
There are various modes you can use to add surround effects or play stereo through more than just the normal two speakers.
SFC (Sound Field Control)
RECEIVER
AV
SYSTEM
RECORDER
DVD
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
Use SFC modes to add realism and depth to Dolby Digital, DTS, PCM, and analogue stereo
sources.
This mode is effective on music sources.
(Music)
SFC
CH
Press MUSIC
to select one of the following modes
or
SFC
DIRECT TUNING
SKIP
DRIVE SELECT
SLOW/SEARCH
(Live)
Suitable for pop and rock.
MANUAL SKIP
(Pop/rock)
ENTER
SUBWOOFER
DIMMER
EFFECT
NEO : 6
For adding gloss to vocals.
CTIONS
FUN
TOP
ME
TOUCH PLAY
ONE
LEVEL
(Vocal)
RETURN
(Jazz)
Adds the reverberations you would experience in an intimate jazz club.
Adds the echoes and feeling of space you would experience in a dance
hall.
TV
VOL
(Dance)
This mode uses all available speakers so that sound is in stereo regardless
of the direction you are facing, and is useful at parties where listeners are
spread out.
TV/AV
SFC
MUSIC
Adds reverberation and depth that makes you feel like you were in a
concert hall.
PLAY
DVD RECORDER
SUB MENU
OFF
You can also press
-/--
PAUSE
STOP
N
DIRECT NAVIGATO U
R
VOLUME
0
DISC
MOVIE
AUTO
TEST
to select the modes after you have pressed MUSIC
MUTING
(Party)
To cancel, press
OFF
Use this mode when playing movies.
(Movie)
SFC
Press
MOVIE to select one of the following modes
or
SFC
You can also press
to select the modes after you have pressed
MOVIE
For dramas and other material where dialogue is important.
(Drama)
For action movies and other material where impact is important.
(Action)
To make you feel like you were in the stadium.
(Sports)
Makes you feel like you are in a theater.
(Musical)
Enjoy gaming with more impact.
(Game)
To cancel, press OFF
24
RQTV0156
SA-XR58.indb 24
6/27/2006 6:55:17 PM
LEVEL
Press
to select the speaker you want to adjust, then press
ENGLISH
Surround sound
Adjusting SFC (Sound Field Control)
Adjusting the output level
to adjust the level.
C (center), RS (surround right), SBR (surround back right), SBL (surround back left), (SB when you have connected only one
surround back speaker), LS (surround left)
Adjustment range: -20 dB to +10 dB
Factory setting: 0 dB
SUBW (Subwoofer)
Adjustment range: --- (off), MIN (minimum), 1 to 29, MAX (maximum)
Factory setting: 20
Adjusting the effect level
EFFECT
Press
, then press
to adjust the level.
Adjustment range: EFFECT 1 (minimum) to EFFECT 10 (maximum)
Factory setting: EFFECT 5
You cannot adjust the effect level in the “PARTY” mode (➡ page 24).
Note
• In “PARTY” mode, you can only adjust the subwoofer output level (➡ page 17).
• You can only adjust speakers if you have connected them (➡ pages 13, and 14 to 17) and set them as present (“Speaker and size settings”, ➡ page
27).
• You may be unable to use some of these surround effects with some sources.
• These settings are saved even if you turn the unit off.
• You cannot use SFC modes unless you have connected center or surround speakers.
• When in “PARTY” mode and you have connected a single surround back speaker (the left surround back speaker), there will be no sound from
that speaker unless you have also connected a center speaker. Similarly, there will be no sound from your center speaker unless you have also
connected a surround back speaker (the left surround back speaker).
• There may be some distortion with some input sources and modes. Reduce the effect level (➡ above), or choose another mode.
25
RQTV0156
SA-XR58.indb 25
6/27/2006 6:55:18 PM
ENGLISH
Receiver settings
Basic operations
INPUT SELECTOR
Receiver settings
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
HDMI
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
TUNE
SURROUND
AUX
1
ENTER
ENTER
RETURN
AUTO DETECTOR
S VIDEO IN VIDEO IN
MENU
SETUP
MENU
SETUP
SETUP MIC
RETURN
L AUDIO IN R
Enter the setup menu.
Press and hold
MENU
SETUP
for about 2 seconds.
RETURN
2
2a
Select the item you want to change.
INPUT SELECTOR
Turn
to select the item.
• Refer to pages 27, 28, and 29 for each item
settings.
• For “REMOTE 1”, refer to page 37 to change
the remote control code.
ENTER
Press
to confirm.
INPUT SELECTOR
2b
Turn
to select a sub-item.
ENTER
Press
3
to confirm.
Change the setting.
INPUT SELECTOR
Turn
Press
to change the setting.
ENTER
to confirm.
Repeat 2b and 3 for other sub-item settings.
4
Exit the menu.
Press
MENU
SETUP
repeatedly until “EXIT” appears.
RETURN
Press
ENTER
to confirm.
• The previous display reappears.
• You can also turn [INPUT SELECTOR] to select “EXIT”.
To return to the previous display/To cancel
Press
MENU
SETUP
RETURN
26
RQTV0156
SA-XR58.indb 26
6/27/2006 6:55:19 PM
2b Select the speaker you want to
set and confirm.
SUBW:
LR:
C:
S:
SB:
3 Change the setting and confirm.
SUBW (Subwoofer)
NO: Unconnected
Speaker and size
settings
When you have set the front speakers (LR)
as “LARGE”
• The subwoofer outputs bass even when
• Set the speakers and their
you are playing analogue or PCM stereo
sizes.
sources.
• Different speakers play different • The sound recorded for the LFE (low
ranges. Change the size setting
frequency effect) channel is played through
to achieve a satisfactory bass.
the subwoofer.
• Only change this setting if
For your reference
auto speaker setup has not
produced a satisfactory result.
• The “SMALL” setting allows you to set the low
pass filter to suit the frequency range of your
speakers. (➡ below)
• The following settings are automatic:
“SUBW” (subwoofer) is set to “YES” if you
set “LR” (front) to “SMALL”. “LR” is set to
“LARGE” if you set “SUBW” to “NO”.
• “SB” (surround back) have the same size setting
as “S” (surround).
2a Select and confirm.
Distance
Enter the distance of the
speakers from the seating
position so that the sound from
all the speakers (except for the
subwoofer) reaches you at the
same time.
ENGLISH
Subwoofer
Front speakers
Center speaker
Surround speakers
Surround back speakers
YES : Connected
(factory setting)
LR (Front), C (Center), S (Surround)
NONE: Speakers not connected (center or
surround)
SMALL : Speakers that cannot adequately
reproduce the bass range (sufficient for
most speakers when using a subwoofer)
(factory setting).
LARGE: Speakers that can reproduce a full
sound range, down to 20 Hz.
SB (Surround back)
NONE: Not connected
1-SPK: 1 connected
2-SPK : 2 connected (factory setting)
RETURN (Returns to the main menu)
L, R: Front speakers
LS, RS: Surround speakers
2b Select the speaker you
want to set and confirm.
m
3 Select the distance
and confirm.
m
C: Center speaker
SBL, SBR: Surround back
speakers
Adjustment range: 0.5 m to 15.0 m
Factory settings:
L, R (Front), C (Center)
LS, RS (Surround), SBL, SBR (Surround back)
3.0 m
1.5 m
Note
“OVER” appears if a speaker was detected as being
more than 15.0 m away during auto speaker setup.
LR BI-WIRE setting
2a Select and confirm.
YES: You have bi-wired your front speakers
NO: You have not bi-wired your front speakers
Change this setting if you have
bi-wired your front speakers
(➡ page 13).
3 Select and confirm.
Factory setting: NO
Low-pass filter
• Only necessary if you have set
speaker size to “SMALL”
(➡ above).
• Small speakers are unable
to reproduce the bass range
adequately, so set the filter to
match the range of your speakers
so that more bass is output from the
subwoofer.
• Only change this setting if auto
speaker setup has not produced a
satisfactory result.
Auto Setup
• Reset the settings done in auto
speaker setup.
• Choose whether to check speaker
polarity during auto speaker setup.
(If polarity is reversed, a minus sign
(-) appears besides the distance
reading, for example, “L 3.0 -”
to show that polarity has been
corrected.)
Receiver settings
2a Select and confirm.
2a Select and confirm.
3 Select the cut-off frequency and confirm.
The settings are 80 Hz, 100 Hz, 120 Hz,
140 Hz, 160 Hz, 180 Hz, and 200 Hz.
Factory setting: 100
For your reference
The filter applies to any speakers you have set as “SMALL”.
Reset
Polarity
2a Select and confirm.
2b Select and confirm.
3 Select and confirm.
2a Select and confirm.
YES: Reset all
auto speaker
setup settings
NO: To cancel
Factory setting:
NO
2b Select and confirm.
3 Select and confirm.
CHECK NO: Do
not check polarity
CHECK YES: To
check polarity
Factory setting:
CHECK YES
27
RQTV0156
SA-XR58.indb 27
6/27/2006 6:55:22 PM
ENGLISH
Receiver settings
INPUT SELECTOR
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
MENU
SETUP
TUNE
SURROUND
AUX
S VIDEO IN VIDEO IN
➡
ENTER
ENTER
RETURN
AUTO DETECTOR
Receiver settings
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
MENU
SETUP
HDMI
RETURN
SETUP MIC
L AUDIO IN R
page 26 for basic operations
Digital input settings
2a Select and confirm.
• Change these settings to suit
the connections you have made 2b Select the equipment and confirm.
to the digital input terminals
(➡ pages 6, 7, 9, and 10).
• You cannot allocate more
3 Change the digital input setting and confirm.
than one terminal per input.
Therefore, if you change the
setting for “DVD” to “OPT 1”,
digital input for DVD input will
Repeat 2b and 3 to change other settings.
be only through the OPTICAL 1
terminal.
2a Select and confirm.
2b Select the equipment and confirm.
TV:
DVR:
DVD:
CD:
Television
DVD recorder
DVD player
CD player
Factory setting:
TV:
OPT1 (OPTICAL 1)
DVR:
OPT2 (OPTICAL 2)
DVD:
COAX1 (COAXIAL 1)
CD:
COAX2 (COAXIAL 2)
TV:
DVR:
DVD:
CD:
Television
DVD recorder
DVD player
CD player
AUTO:
The unit automatically
detects whether input is
digital or analogue. (HDMI
takes priority when input
is digital.)
Analogue input fixed
Digital input fixed
PCM (from CDs) digital
input fixed
3 Select the setting and confirm.
Input signal
• This unit automatically detects
whether input is digital or
analogue, but you can fix the
input mode.
• Select “AUTO” if it isn’t
necessary to fix a certain
signal.
Repeat 2b and 3 to change other settings.
PCM FIX mode
• In rare cases, the unit may have trouble
recognizing the digital signals on discs. Use this
mode if the beginnings of tracks are cut off when
playing CDs.
• Do not use this mode if the unit can handle audio
from CDs normally.
• When PCM FIX mode is on, the unit cannot
process other signals. Choose another mode if
PCM FIX causes noise.
ANALOG:
DIG:
PCMFIX:
Factory setting:
TV, DVR, DVD, CD: AUTO
For your reference
• “DIGITAL INPUT” lights after fixing
digital input.
• “PCM” lights if you select the PCM FIX
mode.
• “PCM FIX” flashes on the display if you
input any signal other than PCM after
you have set the PCM FIX mode.
Delay time
Balance
Speaker
(cross section of
a speaker)
Difference
2 Select and confirm.
2 Select and confirm.
2a Select and confirm.
• This option appears after you
have set “LR BI-WIRE setting”
to “YES” (➡ page 27).
• Adjust high frequency (HF) and 3 Adjust and confirm.
low frequency (LF) balance.
• Correct HF and LF delay time.
2a Select and confirm.
Bi-amp settings
Use the bar as a guide.
LF: low frequency
HF: high frequency
3 Adjust and confirm.
cm
Adjustment range: 0 to 30 cm
Adjust in 1-cm increments.
Factory setting: 0 cm
28
RQTV0156
SA-XR58.indb 28
6/27/2006 6:55:24 PM
page 26 for basic operations
HDMI settings
• Specify the DVD equipment you
have connected to the HDMI
terminal.
• To reduce standby power
consumption.
• Choice for turning off the HDAVI
Control (➡ page 21).
2a Select and confirm.
2a Select and confirm.
2b Select and confirm.
2b Select and confirm.
OFF:
DVR:
You have
connected a DVD
recorder (factory
setting)
You have
connected a DVD
player
ON:
Clear audio at low
volume
Set the dynamic range (the
difference between the loudest
and softest sounds) compression
for Dolby Digital. Use this function
when you have to turn the volume
down, such as late at night. It
compresses the dynamic range so
that you can still hear dialogue and
leave the sound field unaffected.
Attenuating analogue
input
Analogue input can cause
distortion and the “OVERFLOW”
warning to appear on the display.
Turn the attenuator on if this
occurs.
Delaying audio
Delay audio if there appears to
be a difference in timing between
audio and pictures.
Resetting factory
settings
Do the necessary settings again
after this.
2a Select and
confirm.
2b Select and
confirm.
3 Select the equipment 3 Select and confirm.
and confirm.
DVD:
Turning the
ADVANCED DUAL
AMP off
HDAVI Control
Standby selection
3
Standby power consumption
reduced (approximately 0.35
W).
• Signals from DVD
equipment cannot pass
through HDMI connection to
the television when the unit
is in standby (➡ page 5).
• HDAVI Control (➡ page 21)
does not work when the unit
is in standby.
Normal standby power
consumption (factory setting)
2 Select and confirm.
3 Select and confirm.
2 Select and confirm.
3 Select and confirm.
OFF:
HDAVI Control
is OFF
ON:
HDAVI Control
is ON (factory
setting)
The Advance Dual Amp is off
AUTO:
The Advanced Dual Amp works
when possible
Factory setting: AUTO
OFF:
Off
STANDARD:
The level recommended by
the producer of the software
for household viewing.
MAX:
The maximum
allowable compression
(recommended for night
viewing)
Note
2 Select and confirm.
3 Select and
confirm.
OFF:
3 Select a level and confirm.
This function depends on the disc so it may not
work at times.
ENGLISH
Selecting Input
Receiver settings
➡
Factory setting: OFF
OFF:
Off
ON:
On
Factory setting: OFF
Select “OFF” to cancel.
2 Select and confirm.
3 Select and confirm.
OFF:
No delay
ON:
Audio delayed
Factory setting: OFF
2 Select and confirm.
3 Select and confirm.
Select “NO” to cancel.
YES:
Reset all settings to those made in
the factory
NO:
Cancel
Factory setting: YES
Note
Input switches to TUNER after you select “YES”. (Preset channels remain intact.)
29
RQTV0156
SA-XR58.indb 29
6/27/2006 6:55:26 PM
SLOW/SEARCH
SKIP
PLAY
DVD RECORDER
MANUAL SKIP
TOUCH PLAY
ONE
TOP
ME
Basic operations
DRIVE SELECT
NU
�DIRECT NAVIGATOR
Sound effects/Other functions
PAUSE
NCTIONS
�FU
ENGLISH
STOP
ENTER
SUB MENU
RETURN
Sound effects/Other functions
SUBWOOFER
INPUT SELECTOR
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
MENU
SETUP
TUNE
SURROUND
VOLUME
AUX
1
ENTER
MENU
SETUP
ENTER
EFFECT
NEO : 6
RETURN
AUTO DETECTOR
S VIDEO IN VIDEO IN
LEVEL
VOL
HDMI
INPUT SELECTOR
SPEAKERS
A
B
TV
DIMMER
OFF
SFC
RETURN
SETUP MIC
TV/AV
MUSIC
MOVIE
AUTO
TEST
MUTING
L AUDIO IN R
Enter the menu.
Press
MENU
SETUP
RETURN
2
Select the item you want to change.
INPUT SELECTOR
Turn
Press
3
to select the item.
ENTER
to confirm.
Change the setting.
INPUT SELECTOR
Turn
Press
4
to change the setting.
ENTER
to confirm.
Exit the menu.
Press
MENU
SETUP
repeatedly until “EXIT” appears.
RETURN
Press
ENTER
to confirm.
• The previous display reappears.
• You can also turn [INPUT SELECTOR] to select “EXIT”.
To return to the previous display/To cancel
Press
MENU
SETUP
RETURN
30
RQTV0156
SA-XR58.indb 30
6/27/2006 6:55:28 PM
ENGLISH
Sound effects
2 Select and confirm.
3 Adjust and confirm.
Adjustment range: -10 dB to +10 dB
Factory setting: 0 dB
Sound effects/Other functions
Adjusting the bass
2 Select and confirm.
Adjusting the treble
Adjusting front
speaker balance
3 Adjust and confirm.
Adjustment range: -10 dB to +10 dB
Factory setting: 0 dB
2 Select and confirm.
L: Front left
R: Front right
3 Adjust and confirm.
Note
Use the bar as a guide.
Press
Adjusting the
subwoofer level
Adjust the subwoofer level while
listening to a source for a more or
lesser bass.
Other functions
Selecting audio
channels
You can switch between the main
and secondary audio soundtracks
of Dolby Digital or DTS sources.
SUBWOOFER
to select a level.
• Factory setting: SUBW 20
• There is no output from the subwoofer if you select “---”.
Dim the display for better viewing
in a darkened room.
Adjustment range: --- (off),
MIN (minimum), 5, 10, 15, 20,
25, MAX (maximum)
Note
• Sound can be distorted if you raise the volume while subwoofer level is high. Reduce subwoofer level if
this occurs.
• You can also make fine adjustments to subwoofer level (“Speaker output and level”, ➡ page 17).
“DUAL PRG” appears on the display when the unit is receiving a signal with dual audio
channels.
2 Select and confirm.
3 Select the audio track and confirm.
2 Select and confirm.
Adjusting the dimness
of the display
You cannot adjust the balance when the
“PARTY” SFC mode is on (➡ page 24).
3 Select a level and confirm.
MAIN: Main audio channel (factory
setting)
SAP: Second audio program
M+S: Main and second channel
Adjustment range:
DIMMER 1 (bright) to DIMMER 3 (dim)
Factory setting: OFF
• To return to the normal brightness, select “DIMMER OFF”.
Press DIMMER
• The display dims to the level you have selected.
• Press again to cancel.
Sleep timer
• The sleep timer turns the unit
off after a set time.
• It does not control any other
components.
Muting
2 Select and confirm.
3 Select the time and confirm.
Times available: 30, 60, 90, 120 (minutes)
Factory setting: OFF
• “SLEEP” lights when the timer is set.
• To check the setting:
Select “SLEEP” again in Step 2.
• To change a setting:
Repeat the procedure from the
beginning.
Press MUTING
“MUTING IS ON” scrolls across the display while output is muted.
Press again to cancel.
Muting also cancels when you adjust the volume or switch the unit to standby.
31
RQTV0156
SA-XR58.indb 31
6/27/2006 6:55:31 PM
ENGLISH
The radio
TUNE
INPUT SELECTOR
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
VOLUME
The radio
INPUT SELECTOR
SPEAKERS
A
B
MENU
SETUP
TUNE
SURROUND
AUX
S VIDEO IN VIDEO IN
ENTER
RECORDER
DVD
TV
RETURN
SETUP MIC
PLAYER
DVD
ANALOG 6CH
TUNER
CD
L AUDIO IN R
INPUT SELECTOR
AV
SYSTEM
ENTER
RETURN
AUTO DETECTOR
RECEIVER
MENU
SETUP
HDMI
VCR
BAND
Basic operations
CH
MENU
SETUP
ENTER
VOLUME
RETURN
Turn to select.
To return to the
previous menu/To
cancel
Press to confirm.
0
DISC
SKIP
STOP
Manual tuning
TOP
M
Select “TUNER”.
1
TUNER
Press
Select “TUNER FM” or “TUNERENTER
AM”.
INPUT SELECTOR
SUB MENU
RETURN
Turn
BAND
TV
SUBWOOFER
DIMMER
OFF
LEVEL
2
MANUAL SKIP
TOUCH PLAY
ONE
TIONS
FUNC
1
PLAY
DVD RECORDER
E
DIRECT NAVIGA NU
TOR
On the main unit
Input the frequency of the station.
SLOW/SEARCH
PAUSE
DRIVE SELECT
On the remote control (Direct tuning)
-/--
DIRECT TUNING
Select “FM” or “AM”.
2
TUNER
Press and hold
for 2 seconds.
BAND
Tune to the station.
NEO : 6
TUNE
Press
EFFECT
TV/AV
SFC
MUSIC
VOL
MOVIE
AUTO
TEST
MUTING
Automatic tuning
Press and hold [TUNE 2 or 1] until the frequency
starts scrolling to start automatic tuning. (Tuning stops
when a station is found or when there is interference.)
3
Press
DISC
DIRECT TUNING
4
Press the numbered buttons to enter the
frequency.
Press
0
e.g. to select 107.90 MHz, press [1] → [0] → [7] → [9]
→ [0]
• If you do not press a button while the cursor is
flashing, the display returns to the frequency being
received.
• If the frequency has not been input correctly,
“ERROR” will be displayed.
• “TUNED” lights when a station is tuned.
• “ST” lights when a stereo FM broadcast is tuned.
Improving reception
DVD recorders and DVD players can interfere with radio reception.
Turn the DVD recorder and the DVD player off or move it further away
from the AM loop antenna if this occurs.
To change the AM frequency step
If the correct AM frequency cannot be tuned in, change the
frequency step to suit your area.
Preparation: Press [-MENU, –SETUP, RETURN] to enter the
menu.
1. Select “TUNER” and confirm.
2. Select “AM STEP” and confirm.
3. Select “AM STEP 9 kHz” or “AM STEP 10 kHz” and confirm.
4. Press [-MENU, –SETUP, RETURN] twice to select “EXIT” and
press [ENTER].
32
RQTV0156
SA-XR58.indb 32
6/27/2006 6:55:33 PM
Preset channels to make selection simpler.
Even if the AC mains lead is disconnected from the household mains socket, the stations remain in the memory for approximately two
weeks.
Presetting stations
1. Tune to the frequency where you want to begin
(➡ page 32).
Tune to FM 87.50 MHz or AM 522 kHz (9 kHz steps),
AM 530 kHz (10 kHz steps) to start from the lowest
frequency.
2. Enter the menu
MENU
SETUP
Press
RETURN
3. Select “TUNER” and confirm.
4. Select “AUTO MEMO” and confirm.
5. Select “START” and press [ENTER].
Select “CANCEL” to cancel.
• During automatic presetting, the memory indicator ( M )
flashes and the frequency scrolls. The memory indicator
and channel numbers are displayed for a second when
a station is preset.
• The last station to be preset is played when presetting
finishes.
• Stations may not preset correctly if broadcasts are too
strong or weak. Preset manually if this is the case.
The radio
Manual presetting
Auto presetting
The FM stations the unit can receive are preset in channels
1 to 30. The AM stations the unit can receive are preset in
channels 21 to 30 (FM stations are replaced if any were
preset in these channels).
ENGLISH
Preset tuning
Preset the stations one at a time.
1. Tune to the station (➡ page 32).
2. Enter the menu.
MENU
SETUP
Press
RETURN
3. Select “TUNER” and confirm.
4. Select “MEMORY” and confirm.
5. Select a channel number and press [ENTER].
“STORED” is displayed.
• To preset other channels, repeat from step 1.
6. Press [-MENU, –SETUP, RETURN] twice to select “EXIT”
and press [ENTER].
You can also preset FM stations in the MONO mode (➡ below).
Selecting channels
On the remote control
• Select the channel.
On the main unit
1. Enter the menu.
MENU
SETUP
CH
Press
• Press the numbered buttons to select the channel.
RETURN
2.
3.
4.
5.
Select “TUNER” and confirm.
Select “TUNE MODE” and confirm.
Select “PRESET” and confirm.
Press [-MENU, –SETUP, RETURN] twice to select “EXIT”
and press [ENTER].
6. Select the channel.
TUNE
0
-/--
To select a two digit number
e.g. 21: [≧10, -/--] → [2] → [1]
Press
• Press and hold to change channels faster.
Select “MANUAL” in step 4 to tune manually again
(➡ page 32).
Reducing excessive noise (on the main unit)
Preparation: Press [-MENU, –SETUP, RETURN] to enter the menu.
During FM stereo reception
You can improve FM reception by switching reception to
monaural.
1. Select “TUNER” and confirm.
2. Select “FM MODE” and confirm.
3. Select “MONO” and confirm.
• “MONO” lights.
• To return to normal reception, select “AUTO”.
4. Press [-MENU, –SETUP, RETURN] twice to select “EXIT”
and press [ENTER].
During AM reception
When there is a lot of noise interference with an AM broadcast,
try switching to this mode.
1. Select “TUNER” and confirm.
2. Select “BEAT PROOF” and confirm.
3. Select “MODE 1” or “MODE 2” and confirm.
4. Press [-MENU, –SETUP, RETURN] twice to select
“EXIT” and press [ENTER].
33
RQTV0156
SA-XR58.indb 33
6/27/2006 6:55:34 PM
MENU
SETUP
TUNE
SURROUND
AUX
ENTER
ENTER
RETURN
AUTO DETECTOR
S VIDEO IN VIDEO IN
RETURN
SETUP MIC
L AUDIO IN R
INPUT SELECTOR
Basic operations
MENU
SETUP
ENTER
RETURN
Turn to select. Press to confirm.
To return to the
previous menu/To
cancel
PTY displays
NEWS
News
AFFAIRS
Current affairs
INFO
Information
SPORT
Sport
EDUCATE
Education
DRAMA
Drama
CULTURE
Culture
SCIENCE
Science
VARIED
Varied
POP M
Pop music
ROCK M
Rock music
M. O. R. M
Middle-of-the-road Music
LIGHT M
Light classical
CLASSICS
Serious classical
OTHER M
Other music
WEATHER
Weather information
FINANCE
Finance
CHILDREN
Children
SOCIAL A
Social affairs
RELIGION
Religion
PHONE IN
Phone in
TRAVEL
Travel
LEISURE
Leisure
JAZZ
Jazz music
COUNTRY
Country music
NATIONAL
National music
OLDIES
Oldies
FOLK M
Folk music
DOCUMENT
Documentary
TEST
Test broadcast
ALARM
Emergency announcement
This remote control can operate Panasonic televisions, DVD
recorders, DVD players, VCRs, and CD players. Note that this
remote control cannot operate some equipment. For details
about the operations, refer to your equipment’s operating
instructions.
You may need to enter a code to operate some equipment
(➡ page 37).
Point the remote control at the equipment you
want to operate.
Television
RECEIVER
AV
SYSTEM
RECORDER
DVD
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
0
DISC
DIRECT TUNING
-/-SLOW/SEARCH
SKIP
STOP
VOLUME
PAUSE
DRIVE SELECT
DVD RECORDER
ENTER
SUBWOOFER
DIMMER
EFFECT
NEO : 6
AV
SYSTEM
To switch the
television’s input
mode
TV/AV
TV
To adjust the
television’s
volume
MOVIE
AUTO
TEST
VOL
To change
channels
sequentially
TV
CH
VOL
TV/AV
SFC
TV
Do this before
trying to operate
the television.
To switch the
television on
or off
RETURN
LEVEL
MUSIC
MANUAL SKIP
TOUCH PLAY
ONE
SUB MENU
OFF
PLAY
To switch the
unit’s input to
“TV”/To switch
the remote
control to the TV
operation mode
CTIONS
FUN
RDS broadcasts/Using the remote control with other equipment
VOLUME
INPUT SELECTOR
SPEAKERS
A
B
MENU
SETUP
HDMI
TOP
ME
INPUT SELECTOR
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
Using the remote
control with other
equipment
N
DIRECT NAVIGATO U
R
ENGLISH
RDS broadcasts
MUTING
Select the
channel
To select a
channel directly
0
-/--
Changing the display
This unit can display the text data transmitted by the radio data
system (RDS) available in some areas.
“ RDS ” lights while RDS signals are being received.
RDS displays may not be available if reception is poor.
1. Press [-MENU, –SETUP, RETURN] to enter the menu.
2. Select “TUNER” and confirm.
3. Select “RDS DISP” and confirm.
4. Select the display mode and confirm.
FREQUENCY: Frequency display
PS DISP: Program service, the station name
PTY DISP: Program type
5. Press [-MENU, –SETUP, RETURN] twice to select “EXIT”
and press [ENTER].
34
RQTV0156
SA-XR58.indb 34
6/27/2006 6:55:37 PM
Point the remote control at the equipment you want to operate.
RECORDER
DVD
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
DISC
DIRECT TUNING
0
PAUSE
TOP
ME
CTIONS
FUN
SUB MENU
OFF
MANUAL SKIP
TOUCH PLAY
ONE
ENTER
To switch the unit’s input
to “DVR” or “DVD”/To
switch the remote control
to the DVD recorder or
DVD player operation
mode
To switch the DVD
recorder/DVD player on
or off
LEVEL
DIMMER
EFFECT
TV
Do this before trying to operate the
DVD recorder.
AV
SYSTEM
To search through the
disc
If you are unable to switch the
drives on the DVD recorder
The DVD recorder is not
responding to the signal from
the remote control.
Do the following to change the
signal, then try switching drives
again.
-/--
SLOW/SEARCH
Slow-motion
You may have to then
press [ENTER] on some
models.
To pause
SLOW/SEARCH
To start play
PLAY
To show the direct
navigator or top menu
To show the FUNCTIONS
window (while stopped)
To return to the previous
screen
SUB MENU
TIONS
FUNC
1. Press [DVD
RECORDER].
2. While pressing [ENTER],
press and hold [1],
[2], or [3] for about 2
seconds.
• The remote control code
switches to 1, 2, or 3,
depending on which
numbered button you
pressed.
• The factory setting is “1”.
ENTER
0
PAUSE
To show sub menus
Preparation: Check the remote
control mode of your DVD
recorder. Read its operating
instructions for details.
To confirm selection of
an item
For selecting tracks and
chapters directly
VOL
Before using this remote
NEO : 6 with a Panasonic
TV/AV
control
DVD
recorder
SFC
AUTO
YouMUSIC
may MOVIE
need to
TESTchange
MUTING the
code in the remote control to
match the remote control mode
of the DVD recorder.
Do this before trying to operate the
DVD player.
SKIP
RETURN
SUBWOOFER
PLAYER
DVD
ANALOG 6CH
RECORDER
DVD
To skip a track or chapter
PLAY
DVD RECORDER
DRIVE SELECT
N
DIRECT NAVIGATO U
R
-/-SLOW/SEARCH
SKIP
STOP
VOLUME
DVD recorder/DVD player
Frame-by-frame
PAUSE
PAUSE
TOP
ME
AV
SYSTEM
N
DIRECT NAVIGATO U
R
RECEIVER
RETURN
To skip ahead 30 seconds
(For DVD recorder only)
To switch the DVD
recorder’s drive (HDD,
disc, and SD) (For DVD
recorder only)
Select the channel (For
DVD recorder only)
Using the remote control with other equipment
ENGLISH
Using the remote control with other equipment
MANUAL SKIP
DRIVE SELECT
To change channels
sequentially
CH
To navigate through
menus
To select a channel
directly
Use these buttons
to select items after
pressing [DIRECT
NAVIGATOR,
TOP MENU], [S,
SUB MENU], or
[FUNCTIONS].
0
-/--
DISC
To specify a disc (5-disc
changer only) (For DVD
player only)
To stop play
DIRECT TUNING
STOP
1. Press [DVD
RECORDER].
2. While pressing [ENTER],
press and hold [8] for
about 2 seconds.
Note
To restore the original
[FUNCTIONS] activates display functions on some of the Panasonic DVD players.
signal:
In step 2, while pressing
[ENTER], press and hold [9]
for about 2 seconds.
35
RQTV0156
SA-XR58.indb 35
6/27/2006 6:55:42 PM
ENGLISH
Using the remote control with other equipment
Point the remote control at the equipment you want to operate.
VCR
AV
SYSTEM
RECORDER
DVD
TV
TUNER
CD
PLAYER
DVD
ANALOG 6CH
VCR
BAND
CH
VOLUME
0
DISC
DIRECT TUNING
To switch the unit’s
input to “VCR”/To
switch the remote
control to the VCR
operation mode
To switch the VCR
on or off
To start play
SKIP
STOP
SLOW/SEARCH
PAUSE
DRIVE SELECT
DVD RECORDER
TOP
ME
NU
�DIRECT NAVIGATOR
VCR
Do this before trying to
operate the VCR.
AV
SYSTEM
To switch the unit’s
input to “CD”/To
switch the remote
control to the CD
player operation
mode
To switch the CD
player on or off
CD
Do this before trying to
operate the CD player.
AV
SYSTEM
ENTER
SUB MENU
PLAY
To start play
MANUAL SKIP
Fast-forward/rewind
To skip a track
SKIP
SLOW/SEARCH
To pause
To search through
the disc
PAUSE
RETURN
SUBWOOFER
OFF
To change channels
sequentially
TV
DIMMER
LEVEL
EFFECT
NEO : 6
VOL
TV/AV
SFC
MOVIE
AUTO
TEST
PLAY
PLAY
TOUCH PLAY
ONE
MUSIC
CD player
-/--
NCTIONS
�FU
Using the remote control with other equipment
RECEIVER
To pause
SLOW/SEARCH
PAUSE
CH
MUTING
DISC
Select the channel
To select a channel directly
To specify a disc (3or 5-disc changer)
DIRECT TUNING
DISC
0
DIRECT TUNING
-/--
To stop play
STOP
To start play from
a specified disc
[MEGA CD changer]
(holds more than 50
discs)
0
PLAY
To select a track
directly
0
-/--
To stop play
STOP
36
RQTV0156
SA-XR58.indb 36
6/27/2006 6:55:44 PM
Change the code if you find the remote
control unintentionally also controls other
Panasonic equipment.
Do the following to set the remote control
code and this unit’s remote control mode
to the same one.
INPUT SELECTOR
MENU
SETUP
ENTER
RETURN
AUTO
ADVANCED
SPEAKER SETUP DUAL AMP BI-AMP
SPEAKERS
A
B
HDMI
MENU
SETUP
TUNE
SURROUND
VOLUME
AUX
S VIDEO IN VIDEO IN
ENTER
RETURN
AUTO DETECTOR
This remote control can operate Panasonic and Technics audio-visual equipment that
have remote control sensors. You may need to change the remote control code.
It can also operate some other brands of televisions, video cassette recorders, and DVD
players. Check the table for the brand and enter the code as follows.
Changing the codes
TV
VCR
DVD player
TV
VCR
PLAYER
DVD
ANALOG 6CH
0
Press and hold the button
corresponding to the equipment.
INPUT SELECTOR
ENGLISH
Enter a code to operate some equipment
SETUP MIC
0
Enter the first digit.
Enter the second digit.
The remote control outputs the on/off signal.
If the code is correct, the equipment turns on or off.
If it doesn’t, try entering another code.
L AUDIO IN R
INPUT SELECTOR
Basic operations
Turn to select.
• Note that this remote control cannot operate some equipment and that it may not be
able to perform some operations.
• Re-enter the codes after you change the batteries.
Code table
ENTER
MENU
SETUP
RETURN
Press to confirm.
To return to the
previous menu/to
cancel
Change the main unit’s mode
1. Enter the SETUP menu.
MENU
SETUP
Press and hold
for about 2
RETURN
seconds.
2. Select and press [ENTER].
3. Select and press [ENTER].
4. Press [-MENU, –SETUP, RETURN]
twice to select “EXIT” and press
[ENTER].
Change the remote control’s code
TUNER
5. Press
BAND
6. While pressing
hold
ENTER , press and
for about 2 seconds.
To restore the code to “1”
• On the main unit: In step 3, select
“1”.
• On the remote control: In step 6,
while pressing [ENTER], press and
hold [1] for about 2 seconds.
DVD
player
TV
TV
VCR
01/29/30
06/08/16/17/
19/37
02/06/23
08/10/37
–
01/26/29/30/33
–
02/09/23
01
–
NEC
NOKIA
–
05/07/37
–
–
–
–
–
–
NORDMENDE
OCEANIC
OKANO
ORION
15
–
–
31
–
–
01/17
–
02
–
FISHER
FUNAI
GOLDSTAR
GOLDSTAR/LG
GOODMANS
01/29/30/31
07/11/28/36/
37
05/11/12
–
32
28/36
26/41
02/05/10/11/
12/32/38
11/12/32
–
32
11/12
11/12/22/23/
24/25/40
37
02/38
11/12
–
11/12/25/32
–
–
–
–
–
GO-VIDEO
GRUNDIG
–
28/36
HCM
HITACHI
ICE
INNO HIT
ITT
ITT/NOKIA
JVC
KENDO
KENWOOD
LOEWE
LOEWE OPTA
LUXOR
–
01/09/26/41
21/39
34
–
05/07/37
18
40
–
14/33
32
37
MATSUI
02/05/06/07/10/
11/12/25/37/38
–
14/19/28/36
05/07/10/11/12
–
–
03/04/36/37
02/03/18/23/
27/33
–
02/23/26/28/
32/33
02/23
13/14
–
–
08/10/11/37
18/27/37
20/21
08/09/37
–
03/32
–
08/10/11/17/
19/37
03/05/09
26/41
27/35
–
02/03/05/10/
11/12/38
11/12/13/15
11/12
–
–
11/12
–
–
–
39
26/41
07/37
–
11/12/15/21/
25/34/39
07/17/25/37
–
11/12
39/40
11/24
17/20
11/12/17/28/36
02/05/11/12/
22/24/38/40
16
–
05/26/41
06/08/11/12/
14/16/25/32
03/04/06/08
39
11/12/22/40
PANASONIC
AKAI
ALBA
BAIRD
BAUR
BLAUPUNKT
BRANDT
BUSH
DAEWOO
DENON
DUAL
FERGUSON
FINLUX
METZ
MITSUBISHI
01
17/19/21/32
12
–
–
11
–
–
–
–
09
–
15
–
–
–
–
–
06
PHILIPS
PHONOLA
PIONEER
POLKAUDIO
RADIOLA
RAITE
RCA
RFT
ROADSTAR
SABA
SALORA
SAMPO
SAMSUNG
SANYO
SCHAUB LORENZ
SCHNEIDER
SEG
SELECO
SHARP
SIEMENS
SINUDYNE
SONY
TECHNICS
THOMSON
THORN
TOSHIBA
UNIVERSUM
WHITE WESTIN
HOUSE
YAMAHA
ZENITH
–
–
VCR
DVD
player
04/21/36/37
08/10/11/18/
22/27/37
20/21
–
06
05/09
–
–
22/32/33/34/35
32
–
–
–
–
–
33
02/03/18/23/27
21
08/11/17/19/37
–
15/16/18/27
04/16
–
03
16
–
13
02
–
–
02
–
14
10
07/10/11
10
02/03/18/23/27/32
02/18/23/27
–
22
03/10/11/32
–
–
–
–
–
–
08
–
–
24/25/26
–
21
10
05
01
02
–
15/17/19/32
03/08/32/37
–
04
–
–
–
01
07/12
02
–
–
–
Using the remote control with other equipment
Changing the remote
control code
–
37
RQTV0156
SA-XR58.indb 37
6/27/2006 6:55:46 PM
ENGLISH
Specifications/Help messages
Specifications (DIN 45 500)
AMPLIFIER SECTION
Power output (at AC 230 to 240 V)
DIN 1 kHz (T.H.D. 1 %)
2 x 100 W (6 Ω)
20 Hz to 20 kHz continuous power output
both channel driven
2 x 80 W (6 Ω)
Total harmonic distortion
rated power at 20 Hz to 20 kHz
0.09 % (6 Ω)
Power bandwidth
both channel driven, -3 dB
4 Hz to 88 kHz (6 Ω, 0.9 %)
Power output each channel driven (at AC 230 to 240 V)
DIN 1 kHz (T.H.D. 1 %)
Front (L/R)
100 W (6 Ω)
Center
100 W (6 Ω)
Surround (L/R)
100 W (6 Ω)
Surround Back (L/R)
100 W (6 Ω)
Load impedance
Front (L/R)
A or B
6 Ω to 16 Ω
A and B
6 Ω to 16 Ω
BI-WIRE
6 Ω to 16 Ω
Center
6 Ω to 16 Ω
Surround (L/R)
6 Ω to 16 Ω
Surround Back (L/R)
6 Ω to 16 Ω
Frequency response
CD, DVD, DVD Recorder, VCR, TV/STB, AUX
4 Hz to 88 kHz, ±3 dB
DVD 6CH
4 Hz to 44 kHz, ±3 dB
Input sensitivity and impedance
CD, DVD/DVD 6CH, DVD Recorder, VCR, TV/STB, AUX
200 mV/22 kΩ
S/N at rated power (6 Ω)
CD, TV/STB, DVD, DVD Recorder (Digital input)
90 dB (IHF, A: 103 dB)
Tone controls
BASS
50 Hz, +10 dB to -10 dB
TREBLE
20 kHz, +10 dB to -10 dB
Channel balance (250 Hz to 6.3 kHz)
±1 dB
Channel separation
55 dB
Subwoofer frequency response (-6 dB)
7 Hz to 200 Hz
Digital input
(OPTICAL)
(COAXIAL)
2
2
HDMI (Version 1.2a) Input
Output
1
1
FM TUNER SECTION
Frequency range
Sensitivity
S/N 30 dB
S/N 26 dB
S/N 20 dB
IHF usable sensitivity (IHF ’58)
IHF 46 dB stereo quieting sensitivity
87.50 MHz to 108.00 MHz
Help messages
Message
1.5 µV/75 Ω
1.3 µV/75 Ω
1.2 µV/75 Ω
1.5 µV/75 Ω
22 µV/75 Ω
Total harmonic distortion
MONO
STEREO
S/N
MONO
STEREO
Frequency response
Alternate channel selectivity
Capture ratio
Image rejection at 98 MHz
IF rejection at 98 MHz
Spurious response rejection at 98 MHz
AM suppression
Stereo separation
Carrier leak
Channel balance (250 Hz to 6.3 kHz)
Limiting point
Bandwidth
IF amplifier
FM demodulator
Antenna terminal
0.2 %
0.3 %
60 dB
58 dB
20 Hz to 15 kHz, +1 dB, -2 dB
±400 kHz, 65 dB
1.5 dB
40 dB
70 dB
70 dB
50 dB
40 dB
19 kHz, -30 dB
38 kHz, -50 dB
±1.5 dB
1.2 µV
180 kHz
1000 kHz
75 Ω (unbalanced)
AM TUNER SECTION
Frequency range
Sensitivity
Selectivity (at 999 kHz)
IF rejection (at 999 kHz)
VIDEO SECTION
Output voltage at 1 V input (unbalanced)
Maximum input voltage
Input/output impedance
S-Video
Input
Output
Component Video
Input
Output
522 kHz to 1611 kHz (9 kHz steps)
530 kHz to 1620 kHz (10 kHz steps)
20 µV, 330 µV/m
55 dB
50 dB
1± 0.1 Vp-p
1.5 Vp-p
75 Ω (unbalanced)
DVD, DVD Recorder, TV/STB
TV MONITOR
DVD Recorder, TV/STB
TV MONITOR
GENERAL
Power supply
Power consumption
Dimensions (W x H x D)
Mass
AC 230 to 240 V, 50 Hz
140 W
430 mm x 107.5 mm x 390 mm
4.7 kg
Power consumption in standby mode:
Power consumption in HDMI off mode:
0.9 W
0.35 W
Notes:
1. Specifications are subject to change without notice.
2. Mass and dimensions are approximate.
3. Total harmonic distortion is measured by the digital spectrum
analyzer.
Causes and solutions
Muting is on.
Press [MUTING] on the remote control to cancel (➡ page 31).
You are trying to use a feature that is available only in “MUSIC” mode.
Change the mode to “MUSIC” (➡ pages 22 to 23).
Center and surround speakers are not connected, or they are set as absent.
Connect the speakers (➡ page 13) or change their setting to present (➡ page 27).
Surround and surround back speakers are not connected, or they are set as
absent. Connect the speakers (➡ page 13) or change their setting to present
(➡ page 27).
Surround back speakers are not connected, or they are set as absent. Connect
the speakers (➡ page 13) or change their setting to present (➡ page 27).
You are trying to use an effect unavailable with DTS-ES sources.
You are trying to use an effect unavailable with DVD-Audio sources.
You are trying to use an effect unavailable with DVD analogue 6-channel input.
You are trying to use an effect unavailable with the current input source.
(flashing)
You have set the “PCM FIX” mode. Cancel this mode (➡ page 28).
SPEAKERS A is off. Press [SPEAKERS A] to turn on “SPEAKERS A” (➡ page
18).
38
SPEAKERS A and SPEAKERS B are off. Select one of the speakers (➡ page
18).
RQTV0156
SA-XR58.indb 38
6/27/2006 6:55:48 PM
Pages
Common problems
No power.
• Ensure the AC mains lead is connected.
No sound.
Sound is distorted.
•
•
•
•
•
•
•
•
•
Sound stops. “OVERLOAD”
appears on the display for about a
second, and the unit turns off.
• Determine and correct the cause, then turn the unit on.
Causes include:
- Shorting (bare wires touching) of positive and negative speaker wires.
- Using speakers with an impedance lower than that rated for this unit.
- Straining of the speakers through excessive volume or power.
- Using the unit in a hot environment without proper ventilation.
Consult your dealer if the problem occurs again after switching the unit on.
Analogue input becomes distorted
and the message “OVERFLOW”
appears on the display during
playback.
• Switch the attenuator on.
“F76” appears on the display and
the unit turns off.
• Turn the unit off, disconnect the AC mains lead, and consult your dealer.
“F70” appears on the display.
• Turn the unit off, disconnect the AC mains lead, and consult your dealer.
“REMOTE 2” or “REMOTE 1”
appears on the display.
• Match the codes on the main unit and the remote control.
37
Display is dim.
• Cancel “DIMMER”.
31
Clicking sound is heard during
play.
• Depending on the input signal when playing DVD etc., the ADVANCED DUAL AMP function changes
automatically. A clicking sound is heard when it changes. This does not mean a problem with the unit.
➡You can also set the unit against automatic advanced dual amp operations.
Turn the volume up.
Check connections to speakers and other equipment.
Turn on the speakers.
Select the correct source.
Change DIG INPUT setting to suit the type of connection you have made.
Check that the digital signals can be decoded by this unit.
Turn the muting off.
Turn PCM FIX off.
Recording of some DVD-Audio may not be possible due to copyright protection.
Surround effects
11
18
5 to 13
18
18
28
19
31
28
-
13
29
-
ENGLISH
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do
not solve the problem, consult your dealer for instructions.
Troubleshooting guide
Troubleshooting guide
-
29
Pages
Sound is not heard from the
center, surround or subwoofer
speakers.
• Ensure the speaker settings for your speakers are correct.
• Confirm Dolby Pro LogicΙΙx, NEO:6, or SFC settings, and select an adequate mode.
• Switch SURROUND on when you play 2-channel stereo sources.
14 to 17, 27
22 to 25
18
Sound is not heard from the
surround back speaker.
• Ensure the speaker settings for your speakers are correct.
• Switch SURROUND on.
14 to 17, 27
18
Cannot switch SURROUND on.
(Dolby Pro LogicΙΙx, NEO:6, and
SFC are unavailable.)
• Check if the center speaker, surround speakers, and surround back speakers are connected properly.
• Switch SPEAKERS A on.
• You cannot use the SURROUND effect when the input source contains PCM signals with sampling frequencies
of 192 kHz.
• Cancel DVD analogue 6-channel playback.
• You cannot use the effect when the input source contains dual audio signals in Dolby Digital or DTS formats.
There is no DTS audio output.
There is audio output, but the DTS
decoder indicator is not lit.
• Set the DTS Digital Audio Output setting on the DVD player or DVD recorder to “Bitstream”.
Sound is distorted when using the
Sound Field Control (SFC).
• Depending on the input source, sound may be distorted if you increase the SFC effect level. If this happens,
decrease the SFC effect level.
13
18
20
-
25
Pages
Radio
The radio cannot be tuned in
or there is a lot of noise and
interference.
•
•
•
•
•
There is a lot of noise when
listening to AM.
• Try changing the BEAT PROOF mode.
33
The correct AM frequency cannot
be tuned in.
• Change the frequency step to suit your area when AM is selected.
32
Connect the appropriate antenna. (You may need an outdoor antenna or one with more elements.)
Adjust the position of the FM or AM antenna.
Reduce the treble.
Turn off nearby televisions, video decks, DVD recorder, DVD player, and satellite receivers.
Separate the antenna from other cables, cords, and appliances.
11
11
31
-
Pages
HDMI
When using an HDMI connection,
the first few seconds of sound is
cut off.
• Should you be playing a chapter on a DVD:
- Change the audio output setting on the DVD player or DVD recorder from “Bitstream” to “PCM”.
(6.1-channel sources will however be played as 5.1-channel.)
- Select “PCMFIX” as instructed in “Input signals” when you play 2-channel sources.
“U 70-1-1” appears on the display.
• The equipment connected by the HDMI cable is not compatible with the unit’s copyright protection technology.
-
“U 70-1-2” appears on the display.
• The unit has received a signal for a picture format that is incompatible with the HDMI connection. Check the
settings of the connected equipment.
-
“U 70- 3” appears on the display.
• Should anything unusual happen using an HDMI connection:
Consult your dealer if the sign remains on the display after these steps.
- Turn the connected equipment off and on again.
- Pull out the HDMI cable then reinsert it.
- Reduce the amount of equipment connected in series to the HDMI terminal if exceeding 2 units.
The unit does not work properly.
• The unit does not work properly when wrong cords are in HDMI input and output terminals. Turn the unit off,
unplug the AC mains lead, and make connections again.
HDAVI Control does not function
properly.
• Connect the unit to your TV (VIERA) using the HDMI cable, switch the TV on, unplug the unit’s AC mains lead,
and insert it into a household mains socket again.
Remote control
28
5, 21
5, 21
-
Pages
The remote control does not work.
• Replace the batteries if they are worn.
3
Other products respond to the
remote control.
• Change this unit’s remote control code to “REMOTE 2”.
37
39
RQTV0156
SA-XR58.indb 39
6/27/2006 6:55:49 PM
Supplied accessories
Please check and identify the supplied accessories.
1 AC mains lead
1 FM indoor antenna
1 Remote control
Calibration microphone
(EUR7662YN0)
1 AM loop antenna
2 Batteries
Use numbers indicated in parentheses when asking for
replacement parts.
-If you see this symbolInformation on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with
general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a
free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an
equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest
designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
NORSK
SUOMI
ADVARSEL!
VAROITUS!
ADVARSEL:
VAROITUS:
• APPARATET MÅ IKKE PLASSERES I EN BOKHYLLE, ET
INNEBYGGET KABINETT ELLER ET ANNET LUKKET STED
HVOR VENTILASJONSFORHOLDENE ER UTILSTREKKELIGE.
SØRG FOR AT GARDINER ELLER LIGNENDE IKKE
FORVERRER VENTILASJONSFORHOLDENE, SÅ RISIKO
FOR ELEKTRISK SJOKK ELLER BRANN FORÅRSAKET AV
OVERHETING UNNGÅS.
• APPARATETS VENTILASJONSÅPNINGER MÅ IKKE DEKKES
TIL MED AVISER, BORDDUKER, GARDINER OG LIGNENDE.
• PLASSER IKKE ÅPEN ILD, SLIK SOM LEVENDE LYS, OPPÅ
APPARATET.
• BRUKTE BATTERIER MÅ KASSERES UTEN FARE FOR
MILJØET.
FOR Å REDUSERE FAREN FOR BRANN, ELEKTRISK
STØT ELLER SKADER PÅ PRODUKTET, MÅ DETTE
APPARATET IKKE UTSETTES FOR REGN, FUKTIGHET,
VANNDRÅPER ELLER VANNSPRUT. DET MÅ HELLER IKKE
PLASSERES GJENSTANDER FYLT MED VANN, SLIK SOM
BLOMSTERVASER, OPPÅ APPARATET.
• ÄLÄ ASENNA TAI LAITA TÄTÄ LAITETTA
KABINETTITYYPPISEEN KIRJAKAAPPIIN TAI MUUHUN
SULJETTUUN TILAAN, JOTTA TUULETUS ONNISTUISI.
VARMISTA, ETTÄ VERHO TAI MIKÄÄN MUU MATERIAALI
EI HUONONNA TUULETUSTA, JOTTA VÄLTETTÄISIIN
YLIKUUMENEMISESTA JOHTUVA SÄHKÖISKU- TAI
TULIPALOVAARA.
• ÄLÄ PEITÄ LAITTEEN TUULETUSAUKKOJA
SANOMALEHDELLÄ, PÖYTÄLIINALLA, VERHOLLA TAI
MUULLA VASTAAVALLA ESINEELLÄ.
• ÄLÄ ASETA PALAVAA KYNTTILÄÄ TAI MUUTA AVOTULEN
LÄHDETTÄ LAITTEEN PÄÄLLE.
• HÄVITÄ PARISTOT LUONTOA VAHINGOITTAMATTOMALLA
TAVALLA.
TULIPALO-, SÄHKÖISKUVAARAN TAI TUOTETTA KOHTAAVAN
MUUN VAHINGON VÄHENTÄMISEKSI EI LAITETTA SAA
ALTISTAA SATEELLE, KOSTEUDELLE, VESIPISAROILLE TAI
ROISKEELLE, EIKÄ NESTETTÄ SISÄLTÄVIÄ ESINEITÄ, KUTEN
ESIMERKIKSI MALJAKOITA, SAA ASETTAA LAITTEEN PÄÄLLE.
DETTE APPARATET ER BEREGNET TIL BRUK UNDER
MODERATE KLIMAFORHOLD.
TÄMÄ LAITE ON TARKOITETTU KÄYTETTÄVÄKSI LEUDOSSA
ILMASTOSSA.
Utstyret bør plasseres i nærheten av AC-stikkontakten, og støpslet
må være lett tilgjengelig hvis det skulle oppstå problemer.
Laite tulee asettaa lähelle verkkopistorasiaa ja pistokkeen täytyy
olla sellaisessa asennossa, että siihen on helppo tarttua ongelman
sattuessa.
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using chemically treated cloth, carefully read the instructions that came with it.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://panasonic.net
En
RQTV0156-1B
H0606MT1076
SA-XR58.indb 40
6/27/2006 6:55:50 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement