advertisement
▼
Scroll to page 2
of 8
SC-EN35 is used in the illustrations unless otherwise mentioned. Operating Instructions CD Stereo System Dear customer Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. Model No. These instructions are applicable to the following systems. System SC-EN35 SC-EN33 Main unit SA-EN35 SA-EN33 Speakers SB-EN35 SB-EN35A SB-EN33 SB-EN33A SC-EN35 SC-EN33 Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about any of the check points, or if the solutions indicated in the chart do not solve the problem, consult your dealer for instructions. No play. MP3 cannot be read. Sound is unfixed, reversed or comes from one speaker only. No sound or there is a lot of noise. • • • • • • The disc isn’t correctly set. The disc is scratched or dirty. (Tracks skipped.) There is moisture on the lens. Wait for about an hour and then try again. You may not be able to play MP3 if you have copied a multi-session disc that has no data between sessions. When creating a multi session disc, it is necessary to close the session. The amount of data on the disc is too small. Set the amount of data to greater than approximately 5 MB. • Check the speaker connections. (➡ page 3) • • • • Noise may occur when playing MP3 if recording quality is poor. Keep this unit away from mobile telephones if the interference is apparent. Turn the volume up. Switch the unit off, determine and correct the cause, then switch the unit on. Causes include shorting of the positive and negative speaker wires, straining of the speakers through excessive volume or power, and using the unit in a hot environment. Humming heard during play. • An AC mains lead or fluorescent light is near the cords. Keep other appliances and cords away from this unit’s cables. A beat sound or noise is heard while receiving a radio broadcast. • Switch the TV or other audio player off or separate it from the unit. • Switch off the portable audio player connected to “MUSIC PORT”. A low hum or noise is heard during AM broadcasts. The picture on the television near the set disappears or stripes appear on the screen. • Keep the antenna away from other cables and cords. • Keep the AM antenna away from the unit. Remote control doesn’t work. • The location and orientation of the antenna are incorrect. • The television antenna wire is too close to the unit. Separate the antenna wire of the television from the unit. • Check that the batteries are inserted correctly. (➡ page 2) • Replace the batteries if they are worn. Display --:-- • You plugged the AC mains lead in for the first time and there was a power failure recently. Set the time. (➡ page 6) PGM FULL • The number of programmed tracks is limited to 24. No further tracks can be programmed. NO PLAY • A CD-ROM disc that is not CD-DA or MP3 format is inserted. It cannot be played. ERROR • Incorrect operation performed. Read the instructions and try again. F76 • There is a power supply problem. Consult the dealer. USB SC-EN35 No response when [USB q/h] button is pressed. • Disconnect the USB device and then reconnect it back. Alternatively, turn the unit off and then back on. The USB drive or it’s contents cannot be read. • The USB drive format or it’s contents is/are not compatible with the system (➡ page 5). • The USB host function of this product may not work with some USB devices. • USB devices with storage capacity of more than 8 gigabytes may not work in some instances. Slow operation of the USB flash drive. • Large file size or high memory USB flash drive takes longer time to read. “USB OVER CURRENT ERROR” • The USB mass storage device rating exceeds 500mA. Disconnect the USB device. Turn the unit off and then back on. “NO PLAY” • Check the content. • Only MP3 format files can be played. Matsushita Electric Industrial Co., Ltd. Web Site: http://panasonic.net E GN GCS En RQTV0167-2B H0107FL2047 SC-EN35 E,GN,GCS PP.indd 1 22/03/2007 17:17:14 The remote control Supplied accessories Use the numbers indicated in parentheses when asking for replacement parts. 4 SC-EN33 • Insert so the poles (+ and – ) match those in the remote control. • Do not use rechargeable type batteries. 2 (As of January 2007) 1 Remote control [➡ page 2] SC-EN35 (N2QAYB000107) ■ Batteries 3 1 1 AC mains lead [➡ page 3] For Australia and N.Z. R6/LR6, AA (N2QAYB000108) 1 FM/AM antenna [➡ page 3] ■ Use For other areas • Aim at the sensor, avoiding obstacles, at a maximum range of 7 m directly in front of the unit. • Operation can be affected by strong light sources, such as direct sunlight, and the glass doors on cabinets. 2 Batteries [➡ page 2] SA-EN35 • The included AC mains lead is for use with this unit only. Do not use it with other equipment. • Do not use an AC mains lead from other equipment. Remote control signal sensor Control guide [SLEEP] SLEEP timer operation ON/OFF or SLEEP time setting [z PLAY] Timer PLAY ON/OFF [;, OPEN/CLOSE] Open and Close CD lid Standby/on switch [^] Clock and Timer setting [CLOCK/TIMER] [1-9, 0, ≧10] Numbered buttons To select a 2-digit number e.g. 16: [ ≧10] [1] [6] To select a 3-digit number e.g. 226: [ ≧10] [ ≧10] [2] [2] [6] CD/MP3 Program, Tuner Preset (Manual) [PGM, -AUTO PRESET] [Long press] Tuner Preset (Auto) CD/MP3/USB: Delete all programs [CLEAR] Delete last programmed track [DEL] SC-EN33 [CD q/h] Selector switch to CD. Direct CD Play/CD Pause SC-EN35 [FM/AM] Selector switch to Tuner for FM and AM. [TUNER/BAND] Selector switch to Tuner for FM and AM. [MUSIC PORT] Selector switch to MUSIC PORT [g] Stop button SC-EN35 Selector switch to USB. Direct USB Play/USB Pause [USB q/h] [2/u, 1\i] CD: Skip/Search MP3/USB: Track Skip TUNER: Tune up/down, [Long press] Auto tuning Turn the volume up/down [VOL-], [+VOL] Previous/Next Album [ , ALBUM] [PLAY MODE] Play mode button [SURROUND] SURROUND mode ON/OFF Confirm track selection during MP3/USB Program Mode [ENTER] [REPEAT] Repeat ON/OFF [DISPLAY] CD: CD Display (Elapsed play time/Remaining play time) MP3: MP3 Display (Elapsed time/Album name/Track name/ ID3 [Album]/ID3 [Track]/ID3 [Artist]) USB: USB Display (Elapsed time/Remaining time/Album name/Track name/ID3 [Album]/ID3 [Track]/ID3 [Artist]) RDS: RDS Display (Station Name/Program Type/Frequency) Preset EQ mode selector [PRESET EQ] SC-EN35 FM/AM/MUSIC PORT select button [FM/AM/MUSIC P.] SC-EN35 [USB q/h] Selector switch to USB. Direct USB Play/USB Pause SC-EN33 [MUSIC PORT] Selector switch to MUSIC PORT SC-EN33 FM/AM select button [TUNER/BAND] Display [g] Stop button [CD q/h] Selector switch to CD. Direct CD Play/CD Pause Standby/on switch [8] [; OPEN/CLOSE] Open and Close CD lid Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. SA-EN35 [2/u, 1\i] CD: Skip/Search MP3/USB: Track Skip TUNER: Tune up/down, [Long press] Auto tuning [- VOLUME +] To adjust the volume 0 (Minimum) USB port Remote control signal sensor 50 (Maximum) Music port jack Placement of speakers Right Speaker Left Speaker L R 2 AC mains lead Left and right speakers are different. SC-EN35 E,GN,GCS PP.indd 2 Note • Keep your speakers at least 10 mm away from the system for proper ventilation. • These speakers do not have magnetic shielding. Do not place them near televisions, personal computers or other devices easily influenced by magnetism. • You cannot take the front net off the speakers. DC in cord to connect to main set Caution • Use the speakers only with the recommended system. Failure to do so may lead to damage to the amplifier and/or speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance. • Do not attach these speakers to walls or ceilings. 22/03/2007 17:17:21 3 Connections ➡ Page 2 for the position of remote control and main unit buttons. 3. AC mains lead 1. Speakers Connect the DC in cord from left speaker to main set. Silver (-) Copper (+) Note Silver (-) Copper (+) Red Black 2 Black 1 Ferrite core ( For continental Europe ) Connect the AC mains lead. AC IN L Connect the AC mains lead after all other connections are complete. If the unit is left unplugged for longer than approximately two weeks, all settings will revert to the factory settings. Remember to reset the radio stations and any other memory items before using the unit again. R Red To household mains socket 2. FM/AM antenna Stand the antenna up on its base. Taped part SA-EN35 FM antenna L R AM antenna Unplug the antenna connector by holding the taped part. Portable audio equipment (Cords and equipment not included) Headphones (not included) Reduce the volume level and connect the headphones. Plug type: 3.5 mm stereo. Portable audio player Use REMOTE CONTROL MAIN UNIT SC-EN35 SC-EN33 ➡ Note To prevent hearing damage, avoid listening for prolonged periods of time . Plug type: 3.5 mm stereo Start Playback from the Portable audio source. Note • Adjust the volume and sound quality of this unit and the other equipment. • For details, refer to the instruction manual of the other equipment. Discs operations Program play Basic play me/ Press [8] to turn the unit on. Press [; OPEN/CLOSE] to open the CD lid and then set the CD in place. Press [; OPEN/CLOSE] again to close the lid. Keep fingers away from the CD lid when it is closing to avoid possible minor injury. ncy) Label must face outward. Press until you hear it click into place. T The function allows you to program up to 24 tracks. PGM CD Press [PGM, -AUTO PRESET] while stopped. Press the numbered buttons to select tracks. (Maximum 24 tracks) Repeat this step to program other tracks. Press [CD q/h] to start play. Track number Program number Press [CD q/h] to start play. Adjust the volume. Note • Be sure to press the [; OPEN/CLOSE] button to open and close the CD lid. • Damage may occur if the lid is forced closed. • During standby, if the CD is ready in the unit, the unit comes on and play begins. (One touch play) Stop Press [g]. Pause Press [CD q/h]. Press again to resume play. Skip/Search Press [2/u] or [1/i] to skip/ Press and hold [2/u] or [1/i] to search. Note • You can search during play or while paused. • You cannot search through MP3 files. • You can only search within the current track during program play, one track repeat, and random play. Skip album MP3 Direct access play (Play starts with the track you select.) 3 SC-EN35 E,GN,GCS PP.indd 3 Press [ALBUM or Press [ALBUM or in the stop mode. CD ] in the play mode. ] once and then the numbered buttons Press the numbered buttons to select the desired track. MP3 Press [ALBUM or ] to select the album. Press [1/i] once and then press the numbered buttons to select the desired track. MP3 Press [PGM, -AUTO PRESET] while stopped. Press[ALBUM or ] to select your desired album. Press [1/i] once and then press the numbered buttons to select tracks. (Maximum 24 tracks) Press [ENTER]. Repeat step 2 to 4 to program other tracks. Press [CD q/h] to start play. Track number Album number g Confirm a programmed track Press [2/u] or [1/i] when “PGM” is displayed in the stop mode. To check while programming, press [PGM, -AUTO PRESET] twice after “PGM” appears, then press [2/u] or [1/i] . g Delete all programs Press [CLEAR] in the stop mode. “CLR ALL” is displayed. g Cancel program mode Press [PGM, -AUTO PRESET] in the stop mode to clear “PGM” indicator from the display. Note Program contents are stored in the unit’s memory even after changing to a different function or turning the unit off. All program contents are erased by pressing [CLEAR] or by opening the CD lid. 22/03/2007 17:17:32 Discs operations (continued) ➡ Page 2 for the position of remote control buttons. Repeat play Play Mode function Press [PLAY MODE] to select the desired mode. Mode To play 1-TRACK one selected track on the disc. Press the numbered buttons to select the track. 1TR 1-ALBUM MP3 one selected album on the disc. Press [ALBUM or ] to select the album. 1ALBUM RANDOM a disc randomly. RND 1-ALBUM RANDOM MP3 1ALBUM RND all tracks in one selected album randomly. Press [ALBUM or ] to select the album. You can repeat program play or other selected play mode. Press [REPEAT] before or during play. “REPEAT ON” and “ & ” are displayed. To cancel Press [REPEAT] again. “REPEAT OFF” is displayed and “ & ” is cleared. Display function This function allows you to display the information of the current track. Press [DISPLAY] repeatedly during play or pause. CD Elapsed play time Remaining play time MP3 Note • During random play, you cannot skip to previous track. Note on CD-R and CD-RW This unit can play CD-R and CD-RW recorded with CD-DA or MP3. Use an audio recording disc for CD-DA and finalize* it when you finish recording. The unit may not be able to play some discs due to the condition of the recording. * A process performed after recording that enables CD-R/CD-RW players to play audio CD-R and CD-RW. Caution Choose discs with this mark: Do not: • use irregularly shaped CDs. • attach extra labels and stickers. • use CDs with labels and stickers that are coming off or with adhesive exuding from under labels and stickers. • attach scratch-proof covers or any other kind of accessory. • write anything on the CD. • clean CDs with liquids (Wipe with a soft, dry cloth.). Elapsed time Album name ID3 (Artist) ID3 (Track) Track name ID3 (Album) Note • Maximum number of displayable characters: approximately 30 • This unit supports ver. 1.0 & 1.1 ID3 tags. Text data that is not supported will not be displayed. • ID3 is a tag embedded in MP3 tracks to provide information about the track. MP3 The unit can play MP3, a method of compressing audio without overly hurting audio quality. When creating MP3 files to play on this unit • Maximum number of tracks and albums: 999 tracks and 256 albums. • Compatible compression rate: Between 64 kbps and 320 kbps (stereo). 128 kbps (stereo) is recommended. • Disc formats: ISO9660 level 1 and level 2 (except for extended formats). • The time for reading TOC depends on the number of the tracks, the folders or folder structures. Limitations on MP3 • This unit is compatible with multi-session but if there are a lot of sessions it takes more time for play to start. Keep the number of sessions to a minimum to avoid this. • This unit cannot play files recorded using packet write. • If the disc includes both MP3 and normal audio data (CD-DA), the unit plays the type recorded in the inner part of the disc. If the disc includes both MP3 and other types of audio data (e.g. WMA or WAV), the unit plays only the MP3. • Depending on how you create MP3 files, they may not play in the order you numbered them or may not play at all. Radio operations Allocation settings Manual tuning Each country allocates broadcast bands according to their particular system. You can change the AM steps. The step is factory-set to 9 kHz, but you can change it to receive broadcasts allocated 10 kHz steps. Any FM/AM frequencies preset in channels will be changed by this procedure. Preset them again. Select the FM band with SC-EN35 [FM/AM/MUSIC P.] / SC-EN33 [TUNER/ BAND] on the unit. Press and hold SC-EN35 [FM/AM/MUSIC P.] / SC-EN33 [TUNER/BAND] on the unit. After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The minimum frequency changes and the step is changed. To return to the original step, repeat the above steps. Note The preset memory will be initialized when you change your frequency step. Press SC-EN35 [FM/AM] / SC-EN33 [TUNER/BAND] to select “FM” or “AM”. Press [PLAY MODE] to select “MANUAL”. Press [2/u] or [1/i] to select the frequency of the required station. To improve reception FM AM To tune automatically Press SC-EN35 [FM/AM] / SC-EN33 [TUNER/BAND] to select “FM” or “AM”. Press [PLAY MODE] to select “MANUAL”. Press and hold [2/u] or [1/i] until the frequency starts changing rapidly. • Auto tuning stops when it finds a station. • To cancel auto tuning, press [2/u] or [1/i] once again. Note • Auto tuning may not function when there is excessive interference. Memory preset You can preset up to 20 FM channels and up to 12 AM channels. Preparation: Press SC-EN35 [FM/AM] / SC-EN33 [TUNER/BAND] to select “FM” or “AM”. Automatic presetting Press and hold [PGM, -AUTO PRESET] to start presetting. Manual presetting Receive the radio stations after connecting the antenna. Then attach the antenna cord to a wall or pillar where there is good reception. To improve FM sound quality 4 Change the direction and location of the antenna. Press and hold [PLAY MODE] to display “MONO”. To cancel Press and hold [PLAY MODE] again until “MONO” disappears. • MONO is also canceled if the frequency is changed. • Turn off “MONO” for normal listening. SC-EN35 E,GN,GCS PP.indd 4 Press [PLAY MODE] to select “MANUAL”. Press [2/u] or [1/i] to tune to the required station. Press [PGM, -AUTO PRESET]. Press the numbered buttons to select a channel. The station occupying a channel is erased if another station is preset in that channel. Repeat steps 2 to 4 to preset more stations. Selecting a preset station Press the numbered buttons to select the channel. For channels 10 to 20 press [ ≧10], then the two digits. OR Press [PLAY MODE] to select “PRESET”. Press [2/u] or [1/i] to select the channel. 5 22/03/2007 17:17:38 RDS broadcasts For continental Europe Enable you to display the name of a broadcasting station or a program type. “RDS” lights while RDS signals are being received. Press [DISPLAY] to display. Station Name (PS) Program Type (PTY) Frequency display RDS displays may not be available if reception is poor. ➡ Page 2 for the position of remote control buttons. SC-EN35 MP3 The USB connectivity enables you to connect and play MP3 tracks from USB mass storage class. Typically, USB memory devices (Bulk only transfer). Preparation Before connecting any USB mass storage device to the unit, ensure that the data stored therein has been backed up. It is not recommended to use a USB extension cable. The device connected via the cable will not be recognised by this unit. Program type displays NEWS News AFFAIRS Current affairs INFO Information SPORT Sport EDUCATE Education DRAMA Drama CULTURE Culture SCIENCE Science VARIED Varied POP M Pop music ROCK M Rock music M.O.R.M Middle of the road Music LIGHT M Light classical CLASSICS Serious classical OTHER M Other music WEATHER Weather information FINANCE Finance CHILDREN Children SOCIAL A Social affairs RELIGION Religion PHONE IN Phone in TRAVEL Travel LEISURE Leisure JAZZ Jazz music COUNTRY Country music NATIONAL National music OLDIES Oldies FOLK M Folk music DOCUMENT Documentary TEST Test broadcast ALARM Emergency announcement Changing the main unit and remote control mode The remote control and main unit are factory-set to “REMOTE 1” mode. If your remote control affects other equipment during operation, you can switch to operate in “REMOTE 2” mode. SC-EN35 USB operations SC-EN33 Reduce the volume and connect the USB mass storage device. USB enabled device (not included) Press [USB q/h] to start play. To pause play Press [USB q/h]. Press again to resume play. To stop play Press [g]. “RESUME” is displayed. The position is memorized. Press [USB q/h] to resume play. OR Press [g] again to clear the position. To skip track Press [2/u] or [1/i]. To skip album Press [ALBUM or ] in the play mode. Press [ALBUM or ] once and then the numbered buttons in the stop mode. Direct access play (Play starts with the track you select.) Press [ALBUM or ] to select the album. Press [1/i] once and then press the numbered buttons to select the desired track. g Display function Press [DISPLAY] repeatedly during play or pause. Elapsed time Remaining time ID3 (Artist) Album name ID3 (Track) Track name ID3 (Album) For other operating functions, they are similar as those described in “Discs Operations” (➡ page 3 and 4). To remove the USB mass storage device Select a source other than “USB”. Removing the USB mass storage device with it selected as a source can damage the data stored in the device. g Compatible device Devices which are defined as USB mass storage class: • USB devices that support bulk only transfer. • USB devices that support USB 2.0 full speed. g Supported Format Files must have the extension “.mp3” or “.MP3”. Note To switch to “REMOTE 2” mode Press [FM/AM/MUSIC P.] to select “AM”. ( SC-EN35 ) (While pressing and hold SC-EN35 [FM/AM/MUSIC P.] / SC-EN33 [MUSIC PORT] on the main unit) Press and hold [2] until “REMOTE 2” appears on the main unit display. Press and hold [ENTER] and [2] for at least 2 seconds. The main unit and remote control are now set to operate in “REMOTE 2” mode. To return to “REMOTE 1” mode SC-EN35 Perform steps 1 to 3 but use [1] instead of [2] for steps 2 and 3. SC-EN33 Perform steps 2 and 3 above but use [1] instead of [2] for both steps. (“REMOTE 1” appears on the main unit during step 2.) 5 The remote control cannot work with the main unit if their modes are different. “REMOTE 1” or “REMOTE 2” appears on the main unit when you operate the remote control.* * If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.) Press and hold [ENTER] and [1] on the remote control for at least 2 seconds. If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.) Press and hold [ENTER] and [2] on the remote control for at least 2 seconds. SC-EN35 E,GN,GCS PP.indd 5 • CBI (Control/Bulk/Interrupt) is not supported. • A device using NTFS file system is not supported [Only FAT 16/32 (File Allocation Table 16/32) file system is supported]. • Depending on the sector size, some files may not work. • This unit can access up to 255 albums and 2500 tracks. • The maximum number of tracks in a folder are 999 tracks. • Only one memory card will be selected when connecting a multiport USB card reader. Typically the first memory card inserted. • Disconnect the USB card reader from the unit when you remove the memory card. Failure to do so may cause malfunction to the device. • When you connect your digital audio player to the USB jack, it charges all the time except in standby mode. 22/03/2007 17:17:41 Timers and others ➡ Page 2 for the position of remote control buttons. Play timer Setting the time This is a 24-hour clock. Press [CLOCK/TIMER] to set the clock. Press [2/u] or [1/i] to select the time within 5 seconds. (Press and hold to change the time faster.) Press [CLOCK/TIMER] again. g To display the clock when the unit is on Press [CLOCK/TIMER] g To check the time when the unit is off Press [CLOCK/TIMER] You can set the timer to come on at a certain time to wake you up. Preparation: Turn the unit on and set the clock. Prepare the music source you want to listen to; disc, radio, USB or music port source, and set the volume. Press [CLOCK/TIMER] repeatedly to select play timer. CLOCK zPLAY Original display Within 5 seconds, press [2/u] or [1/i] to set the starting time. Note The clock is accurate to within ±60 seconds a month. Readjust if necessary. Set again after disconnecting the AC mains lead or power failure. Press [CLOCK/TIMER] to confirm. Repeat steps 2 and 3 to set the finishing time. Sleep timer The SLEEP timer can turn the unit off after a set time. Press [SLEEP] to turn the SLEEP function ON/OFF. • Each time you press the button: 30 MIN 60 MIN 90 MIN OFF (Canceled) g To check the remaining time To activate the timer Press [zPLAY] to turn on the timer. Press [^] to turn off the unit. 120 MIN Press [SLEEP] once To Action Change the settings Repeat steps 1 to 4 and 6. Change the source of volume Press [zPLAY] to clear zPLAY indicator from the display. Make changes to the source or volume. Perform steps 5 and 6. Check the settings (when the unit is on or in standby mode) Press [CLOCK/TIMER] repeatedly to select zPLAY. Cancel Press [zPLAY] to clear the timer indicator from the display. Note The play timer and sleep timer can be used together. The sleep timer always has priority. Be sure not to overlap timer settings. Sound quality You can choose one of four types of sound quality. Press [PRESET EQ] to select the sound quality. • Each time you press the button: HEAVY (Adds punch to rock) EQ CLEAR (Clarifies higher sounds) EQ OFF (Canceled) SOFT (For background music) VOCAL (Adds gloss to vocals) Live Virtualizer You can create a three-dimensional sound field when listening to stereo sound. Press [SURROUND] to turn the Live Virtualizer ON/OFF. Note The actual effect depends on the source played. Note • The timer will start at the preset time, with the volume increasing gradually to the preset level. • The timer comes on at the set time every day if the timer is on. • The unit must be in the standby mode for the timer to function. • If you turn the unit off and on again while the timer is functioning, the finish time setting will not be activated. • When MUSIC PORT or USB is selected as the source when the timer comes on, the system turns on and engages MUSIC PORT or USB as the source. If you wish to playback from the portable audio equipment, activate the equipment ’s play mode and increase the volume. (See the portable audio equipment’s instruction manual.) Specifications 6 g AMPLIFIER SECTION RMS OUTPUT POWER both channel driven simultaneously 10 % total harmonic distortion (THD) SC-EN35 3 W per channel 2 W per channel SC-EN33 PMPO Output Power For Southeast Asia SC-EN35 90 W 60 W SC-EN33 Output impedance HEADPHONE 16 Ω to 32 Ω MUSIC PORT 14 kΩ DC IN Jack Terminal 14 V Phone Jack Terminal 3.5 mm stereo Music Port Jack Terminal 3.5 mm stereo g TUNER SECTION Frequency range FM 87.50 MHz to 108.00 MHz (50 kHz) AM 522 kHz to 1629 kHz (9 kHz) 520 kHz to 1630 kHz (10 kHz) g CD SECTION Disc played [8 cm or 12 cm] (1) CD-Audio (CD-DA) (2) CD-R/RW (CD-DA, MP3) (3) MP3 Sampling frequency CD 44.1 kHz MP3 32 kHz, 44.1 kHz, 48 kHz Bit rate MP3 32 kbps to 384 kbps SC-EN35 E,GN,GCS PP.indd 6 Decoding Pick up Wavelength Laser power (For Norge) Bølgelengde Laserstyrke 16/20/24 bit linear 785 nm CLASS 1 785 nm Ingen farlig stråling sendes ut (med sikkerhets-beskyttelse) Audio Output (Disc) Number of channels 2 channel Frequency response 20 Hz to 20 kHz (+1, -2 dB) Wow and flutter Below measurement limit Digital filter 8 D/A converter MASH (1 bit DAC) g USB SECTION Playable USB Storage Media (1) HDD (with FAT 32 format and no partition) (2) USB MP3 Player/Digital Audio Player (3) USB Thumbdrives Supported audio file format MP3 Bit Rate USB memory port Maximum current 500 mA Bit rate MP3 32 kbps, 320 kbps Audio Output (MP3) Number of channels 2 channel Frequency response (MP3) 20 Hz to 20 kHz g SPEAKER SECTION Type 1 Way, 1 Speaker system Speaker Unit(s) Full Range Speaker 8 cm cone type 6 Ω Impedance 6Ω Input power 6 W (MAX) Dimensions (W x H x D) 121 mm x 236 mm x 146 mm g GENERAL Power supply For continental Europe AC 230 to 240 V, 50 Hz AC 230 to 240 V, 50 Hz For Australia and N.Z. AC 220 to 240 V, 50/60 Hz For Southeast Asia Power consumption SC-EN35 32 W 16 W SC-EN33 Dimensions (W x H x D) 220 mm x 236 mm x 146 mm Mass With speakers SC-EN35 3.60 kg 3.33 kg SC-EN33 Without speakers SC-EN35 1.30 kg 1.26 kg SC-EN33 Operating temperature range +5 °C to +35 °C Operating humidity range 5 % to 90 % RH (no condensation) Power consumption in standby mode:2.0 W (approx.) Notes: Specifications are subject to change without notice. Mass and dimensions are approximate. 7 22/03/2007 17:17:45 Safety precautions Placement Set the unit up on an even surface away from direct sunlight, high temperature, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the unit’s service life. Do not place heavy items on the unit. Voltage Do not use high voltage power sources. This can overload the unit and cause a fire. Do not use a DC power source. Check the source carefully when setting the unit up on a ship or other place where DC is used. AC mains lead protection Ensure the AC mains lead is connected correctly and not damaged. Poor connection and lead damage can cause fire or electric shock. Do not pull, bend, or place heavy items on the lead. Grasp the plug firmly when unplugging the lead. Pulling the AC mains lead can cause electric shock. Do not handle the plug with wet hands. This can cause electric shock. Foreign matter Do not let metal objects fall inside the unit. This can cause electric shock or malfunction. Do not let liquids get into the unit. This can cause electric shock or malfunction. If this occurs, immediately disconnect the unit from the power supply and contact your dealer. Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit. Service Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these instructions occurs, disconnect the AC power cord and contact your dealer or an authorized service center. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons. Extend operating life by disconnecting the unit from the power source if it is not to be used for a long time. CAUTION! • DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILTIN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS. • DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS. • DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED CANDLES, ON THE UNIT. • DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY MANNER. L R LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT CAUTION! THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. Inside of product Tuotteen sisällä Produktets innside WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, • DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. • USE ONLY THE RECOMMENDED ACCESSORIES. • DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This product may receive radio interference caused by mobile telephones during use. If such interference is apparent, please increase separation between the product and the mobile telephone. The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptable. For Southeast Asia THIS UNIT IS INTENDED FOR USE IN TROPICAL CLIMATES. For other areas THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES. 7 SC-EN35 E,GN,GCS PP.indd 7 -If you see this symbolInformation on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. 22/03/2007 17:17:47 SUOMI NORSK VAROITUS! ADVARSEL! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. DETTE PRODUKTET ANVENDER EN LASER. BETJENING AV KONTROLLER, JUSTERINGER ELLER ANDRE INNGREP ENN DE SOM ER BESKREVET I DENNE BRUKSANVISNING, KAN FØRE TIL FARLIG BESTRÅLING. DEKSLER MÅ IKKE ÅPNES, OG FORSØK ALDRI Å REPARERE APPARATET PÅ EGENHÅND. ALT SERVICE OG REPARASJONSARBEID MÅ UTFØRES AV KVALIFISERT PERSONELL. VAROITUS! • ÄLÄ ASENNA TAI LAITA TÄTÄ LAITETTA KABINETTITYYPPISEEN KIRJAKAAPPIIN TAI MUUHUN SULJETTUUN TILAAN, JOTTA TUULETUS ONNISTUISI. VARMISTA, ETTÄ VERHO TAI MIKÄÄN MUU MATERIAALI EI HUONONNA TUULETUSTA, JOTTA VÄLTETTÄISIIN YLIKUUMENEMISESTA JOHTUVA SÄHKÖISKUTAI TULIPALOVAARA. • ÄLÄ PEITÄ LAITTEEN TUULETUSAUKKOJA SANOMALEHDELLÄ, PÖYTÄLIINALLA, VERHOLLA TAI MUULLA VASTAAVALLA ESINEELLÄ. • ÄLÄ ASETA PALAVAA KYNTTILÄÄ TAI MUUTA AVOTULEN LÄHDETTÄ LAITTEEN PÄÄLLE. • HÄVITÄ PARISTOT LUONTOA VAHINGOITTAMATTOMALLA TAVALLA. VAROITUS: VÄHENNÄ TULIPALON, SÄHKÖISKUN TAI LAITTEISTON VAHINGOITTUMISEN VAARAA • TÄTÄ LAITETTA EI SAA ALTISTAA SATEELLE, KOSTEUDELLE, ROISKEILLE TAI TIPPUVILLE NESTEILLE. LAITTEEN PÄÄLLE EI SAA MYÖSKÄÄN ASETTAA MITÄÄN NESTEELLÄ TÄYTETTYÄ ESINETTÄ, KUTEN MALJAKKOA. • KÄYTÄ VAIN SUOSITELTUJA LISÄVARUSTEITA. • ÄLÄ IRROTA KANTTA (TAI TAUSTAA). SISÄLLÄ EI OLE KÄYTTÄJÄN HUOLLETTAVISSA OLEVIA OSIA. HUOLLON SAA SUORITTAA VAIN AMMATTITAITOINEN HENKILÖKUNTA. Pistorasia tulee asentaa laitteen lähelle helppopääsyiseen paikkaan. Verkkojohdon pistokkeen on oltava aina helposti käytettävissä. Tämä laite voidaan kytkeä kokonaan irti verkkovirrasta irrottamalla verkkojohdon pistoke pistorasiasta. TÄMÄ LAITE ON TARKOITETTU KÄYTETTÄVÄKSI LEUDOSSA ILMASTOSSA. ADVARSEL! • APPARATET MÅ IKKE PLASSERES I EN BOKHYLLE, ET INNEBYGGET KABINETT ELLER ET ANNET LUKKET STED HVOR VENTILASJONSFORHOLDENE ER UTILSTREKKELIGE. SØRG FOR AT GARDINER ELLER LIGNENDE IKKE FORVERRER VENTILASJONSFORHOLDENE, SÅ RISIKO FOR ELEKTRISK SJOKK ELLER BRANN FORÅRSAKET AV OVERHETING UNNGÅS. • APPARATETS VENTILASJONSÅPNINGER MÅ IKKE DEKKES TIL MED AVISER, BORDDUKER, GARDINER OG LIGNENDE. • PLASSER IKKE ÅPEN ILD, SLIK SOM LEVENDE LYS, OPPÅ APPARATET. • BRUKTE BATTERIER MÅ KASSERES UTEN FARE FOR MILJØET. ADVARSEL: FØLG NEDENSTÅENDE INSTRUKSER FOR Å REDUSERE RISIKOEN FOR BRANN, ELEKTRISK STØT OG SKADE PÅ PRODUKTET: • DETTE APPARATET MÅ IKKE UTSETTES FOR REGN, FUKTIGHET, DRYPP ELLER SPRUT, OG INGEN VÆSKEFYLTE GJENSTANDER, SOM F.EKS. VASER, MÅ PLASSERES PÅ APPARATET. • BRUK KUN ANBEFALT TILBEHØR. • IKKE FJERN DEKSELET (ELLER BAKSIDEN); APPARATET INNEHOLDER INGEN DELER SOM KAN SKIFTES ELLER REPARERES AV BRUKEREN. OVERLAT TIL KVALIFISERTE SERVICETEKNIKERE Å UTFØRE SERVICE. Strømuttaket må befinne seg i nærheten av utstyret og være lett tilgjengelig. Støpslet på strømkabelen må være klart til bruk. Når dette apparatet skal kobles helt fra strømnettet (AC), må støpslet på strømkabelen trekkes ut av stikkontakten. DETTE APPARATET ER BEREGNET TIL BRUK UNDER MODERATE KLIMAFORHOLD. Maintenance If the surfaces are dirty 8 To clean this unit, wipe with a soft, dry cloth. • Never use alcohol, paint thinner or benzine to clean this unit. • Before using chemically treated cloth, read the instructions that came with the cloth carefully. SC-EN35 E,GN,GCS PP.indd 8 Care of the CD lens • Clean the lens regularly to prevent malfunctions. Use a blower to remove dust and a cotton swab if it is extremely dirty. Recommended product: Lens cleaner kit (part no. SZZP1038C). • Do not use the lens cleaner of the CD type. 22/03/2007 17:17:50
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project