Panasonic PVDM2092 Operating Instructions

Panasonic PVDM2092 Operating Instructions
Initial Setup
TV/ DVD / VCR Combination
Operating Instructions
PV-DM2092
Basic Operation TV Operation Timer Operation
Model No.
Advanced Operation
• Initial Setup and Connection Procedures are on pages 11 to 17.
LSQT0608A
As an ENERGY STAR Partner, Matsushita Electric Corporation of America
has determined that this product or product model meets the ENERGY STAR
guidelines for energy efficiency.
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P01).p65
1
2002/06/19, 14:51
For Your Information
Ability to play back may depend
on recording conditions.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one wide
blade), or a three-wire grounding type plug. Always
hold the plug firmly and make sure your hands are
dry when plugging in or unplugging the AC power cord.
Regularly remove dust, dirt, etc. on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet only one way. If it cannot be
fully inserted, try reversing it. If it still will not fit, have
an electrician install the proper wall outlet. Do not
tamper with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances
and walking traffic. Do not rest heavy objects on,
or roll such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type
plug (polarized or grounding) and must be securely
connected.
- Overloaded wall outlets or extension cords are
fire hazards.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to discs.
For your protection:
a. Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa,
rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator, in
direct sunlight, inside closed vehicles,
in high temperature [over 95 °F (35 °C)], or in over
75% humidity. If unit is suddenly moved from a
cold place to a warm one, moisture may condense in
unit and on the tape causing damage. Never subject
unit to vibration, impact, or place it so that the
surface is tilted as internal parts may be seriously
damaged.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or stand that is not
firm, level, and adequately strong. The unit could
fall causing serious injury to a child
or adult and damage to the unit.
• Move any appliance and cart
combination with care.
Quick stops, excessive force, and
uneven surfaces may cause objects to overturn.
• Carefully follow all operating instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly
grounded to provide some protection
against built up static charges
and voltage. Section 810
of the National Electrical Code,
ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
regarding proper grounding of
the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE
POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power
lines and electric light or power circuits so it will never touch
these power sources should it ever fall. When installing
antenna, absolutely never touch power lines, circuits or
other power sources as this could be fatal.
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR
MOISTURE, such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug unit and have it inspected by
a qualified service technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, odours, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
Do not put any foreign object on the tray.
• Keep magnetic objects, such as speakers, away from
unit to avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit and
cause electrical shock. Any substance, such as wax, adhesive
tape, etc. may mar the cabinet surface. Exposure to greasy,
humid, or dusty areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or remove
covers, or make any adjustments not described in the manual.
Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified
by the manufacturer, or have equal safety characteristics
as original parts. The use of unauthorized substitutes may
result in fire, electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a thorough safety
check be done as described in the manufacturer’s service
literature to ensure video unit is in safe operating condition.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P02-3).p65
2
2002/06/19, 14:51
Safety Precautions/Mesures de sécurité
Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas
exposer cet appareil à la pluie ou à une humidité excessive.
Attention :Pour éviter les chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu’au fond.
FCC WARNING : Any unauthorized changes or modifications to this equipment
would void the user’s authority to operate.
This television receiver provides display of television closed captioning.
CAUTION:
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY
AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE
UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT LASER
EN CAS D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTICE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this eqiupment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize an
electrical outlet different from that used by the receiver. If necessary, consult the dealer or an
experienced radio/TV technician for help. You may find the booklet, 'Something About Interference'
available from FCC local regional offices helpful.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.
Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance: <http://www.eiae.org.>
This symbol warns the user that uninsulated voltage within the unit
may have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included. Therefore,
it should be read carefully in order to avoid any problems.
Region Management Information
Region Management Information: This unit is designed and
manufactured to respond to the Region Management Information
that is recorded on a DVD disc. If the Region number described
on the DVD disc does not correspond to the Region number of
this unit, this unit cannot play this disc.
The Region number
for this unit is 1.
1
3
DM2092 (P02-3).p65
3
2002/06/19, 14:51
Before Using
Congratulations
Loading the Batteries
on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
and your family years of enjoyment. Please fill
in the information below. The serial number is
on the tag located on the back of your unit.
1) Open the cover.
2) Insert batteries
as marked.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
PV-DM2092
Model No.
Serial No.
3) Close the cover.
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Prevent Accidental Tape Erasure
Break off the tab
to protect.
Record Tab
Accessories
Screw driver
Remote Control
LSSQ0302
To record again.
Cover the hole
with cellophane tape.
Batteries 2 “AA”
Record/Playback Time
Only use tapes with the
Tape Speed
Setting
To order accessories,
call toll free
1-800-332-5368.
4
mark in this unit.
Type of Video Cassette
T60
T120
T160
SP (Standard Play)
1 Hour
2 Hours
LP (Long Play)
2 Hours
4 Hours
SLP (Super Long Play)
3 Hours
6 Hours
2 Hours
40 Minutes
5 Hours
20 Minutes
8 Hours
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P04 Before).p65
4
2002/06/19, 14:51
Table of Contents
Initial Setup
Important Safeguards and Precautions / Safety Precautions ........ 2 - 3
Before Using ........................................................................................ 4
Information (Unit, Cassette, Disc) .................................................. 6 - 7
Location of Controls ..................................................................... 8 - 11
Connections ................................................................................ 11 - 13
Initial Setup .................................................................................. 14, 15
Reset Language, Channels, Clock, Time Zone Adjust .............. 16, 17
TV / VCR
DVD
Playback a Tape ................................................................................ 18
Record On a Tape ............................................................................. 18
Copy Your Tapes (Dubbing) .............................................................. 19
Basic DVD Operation .................................................................. 20, 21
TV Operation
TV / VCR
TV Operation ..................................................................................... 22
MTS Broadcast / TV Stereo System ................................................. 23
Closed Caption System ............................................................... 24, 25
TV Timer Features ............................................................................. 26
On-Screen Display (OSD) ................................................................. 27
FM Radio ..................................................................................... 28, 29
Timer Operation
TV / VCR
Timer Recording .......................................................................... 30, 31
Basic Operation TV Operation Timer Operation
Basic Operation
Initial Setup
TV / VCR
Advanced Operation
DVD
Cable Box Universal Remote Control Feature ............................ 32, 33
Tape Operation ........................................................................... 34 - 37
Special VCR Features ................................................................. 38, 39
V-Chip Control Feature .............................................................. 40 - 43
Audio Features ............................................................................ 44, 45
Video / Audio Menu .......................................................................... 46
Video / Audio Adjustment ................................................................. 47
Disc Operation ........................................................................... 48 - 52
DVD Operation using On-Screen Displays .............................. 53 - 55
MP3 Playback Operation .................................................................. 56
DVD Lock Feature ............................................................................. 57
DVD
TV / VCR
Settings for DVD Operation ....................................................... 58 - 60
Language Code List ......................................................................... 61
Before Requesting Service ......................................................... 62, 63
Warning and Instruction Displays ..................................................... 64
Spanish Quick Use Guide / Guía para rápida consulta ............. 65 - 71
Warranty / Customer Services Directory ..................................... 72, 73
Index ............................................................................................ 74, 75
5
DM2092 (P05 contents).p65
5
2002/06/19, 14:51
For Your Information
For Your Information
Advanced Operation
TV / VCR
Information (Unit, Cassette, Disc)
Head Cleaning
Specifications
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Display
Picture Tube:
20 inch measured
diagonal 90° deflection
Picture Tube
Head Clog Sensor
V I DEO HEADS MAY
During playback this
NEED CLEAN I NG
PL EASE I NSERT HEAD
screen appears if
CLEAN I NG CASSETTE
clogging is detected. To
OR REFER TO MANUAL
remove screen, press
END : PLAY
PLAY on the remote or
• Use “dry” type head cleaning cassette only.
unit.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape directions carefully.
Excessive use of head cleaning tape can shorten
the video head life.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight Saving Time.)
■ Spring (First Sunday in April)
DST : ON ➛ Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST : ON ➛ Turns clock back one hour.
• If your area does not observe Daylight Saving
Time, select DST : OFF (see “Clock” on pages
16 and 17).
• Keep these time changes in mind when
programming the unit for timer recordings.
Features for a Quality Picture
VCR
Video Recording System:4 rotary heads helical
scanning system
Audio Track:
1 track (Normal)
2 channel
(Hi-Fi Audio Sound)
Tuner
Broadcast Channels:
VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels:
Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125
FM Radio
Band range:
General
Power Source:
Power Consumption:
87.5 ~ 108.1 MHz
120V AC, 60 Hz
Power On
Approx. 130 watts
Power Off
Approx. 3.5 watts
Television System:
EIA Standard NTSC color
Speaker:
2 pieces
Operating Temperature: 5 °C ~ 35 °C (41 °F ~ 95 °F)
Operating Humidity:
10 % ~ 75%
Weight:
27 kg (59.4 lbs.)
Dimensions:
604 (W) x 523 (H) x 508 (D) mm
23-13/16” (W) x 20-9/16” (H)
x 20” (D)
Discs played
(1) DVD-VIDEO disc
5” (12 cm) single-sided,
single-layer
5” (12 cm) single-sided,
double-layer
5” (12 cm) double-sided,
double-layer
(one layer per side)
3” (8 cm) single-sided,
single-layer
3” (8 cm) single-sided,
double-layer
3” (8 cm) double-sided,
double-layer
(one layer per side)
(2) Compact disc
5” (12 cm) disc
(CD-DA, VIDEO CD) 3” (8 cm) disc
(3) MP3
Digital audio output:
Optical digital output:
Optical connector
Pickup:
Wavelength:
655 nm (DVD)
790 nm (Video CD/CD)
Laser power: CLASS II
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 number key
on the remote control or CH
on the unit until the
picture clears up. To return to Auto Tracking, press
POWER off, then on again a few seconds later.
V-Lock Control
In Still mode, the 3 or 6 number key on the remote
control or CH
on the unit operate as a V-Lock
Note : Designs and specifications are subject to
change without notice.
control to reduce jitter.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
6
DM2092 (P06-7 Information).p65
6
2002/06/19, 14:51
The unit can play back discs bearing any of the
following marks:
DVD
3” (8 cm) disc / 5” (12 cm) disc
Video CD
3” (8 cm) disc / 5” (12 cm) disc
CD
3” (8 cm) disc / 5” (12 cm) disc
MP3
Discs which cannot be played with this unit
• DVD with Region No. other than “1” or “ALL”
• DVD of PAL system
• CD-ROM
• DVD-RAM
• CDV
• DVD-ROM
• CD-G
• Do not try to play a Photo CD.
is a registered trademark.
Disc Handling
Initial Setup
Disc formats supported by this unit
Handling precautions
• Only hold disc by edges as shown.
Fingerprints, dirt, and scratches
can cause skipping and distortion.
• Do not write on label
side of disc.
• Never use record
cleaning sprays, benzine,
thinner, static electricity
prevention liquids, or any
other solvent.
• Be careful not to drop or
bend disc.
• Do not place more than
1 disc on disc tray.
• Do not try to close disc
tray when disc is not
properly placed.
• Always store discs in their
proper cases when
Disc tray
not in use.
Disc
Definition of Terms
Angle
Some DVD discs feature scenes simultaneously
shot from different angles. The ANGLE button can be
used to view the scene from different angles.
(ANGLE Indicator lights up on the unit when a scene
recorded at different angles is detected.)
To clean disc surface
With a soft, damp (water only) cloth, gently wipe from
the center hole to the outer edge as shown below.
(Wiping in a circular pattern will scratch the surface.)
Chapter Number
Titles are subdivided into numbered sections. You can
quickly search for a favorite scene using these numbers.
DVD
A high-density optical disc on which high-quality
pictures and sound have been digitally recorded.
DVD incorporates new video compression technology
(MPEG II) and high-density recording technology
which allow entire movies to be recorded with
incredible playback quality.
Playback Control
With Video CD (version 2.0), scenes or information
may be selected for viewing or listening from an
interactive menu that appears on the TV screen.
Subtitles
Written dialogue which appears at the bottom of the screen.
Time Number
The elapsed play time from the start of a disc or title.
Use to quickly find scenes. (May not work with some discs.)
Title Number
For DVD discs with two or more titles, the title is
numbered as title 1, title 2, etc.
Track Number
Numbers assigned to tracks on Video CDs and CDs
to allow specific tracks to be quickly located.
Video CD
CD containing picture and sound with same quality
level as video tape. This unit also supports Video
CDs with playback control (version 2.0).
DM2092 (P06-7 Information).p65
7
If disc is brought from a cold to a warm
environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216,
and 4,819,098, licensed for limited viewing uses only.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. Patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
7
2002/06/19, 14:51
Location of Controls
Remote Control Buttons
EJECT/OPEN/CLOSE
DVD
See next page.
Sets to DVD mode.
POWER
LIGHT
Turns the unit on or off.
See next page.
TV/VCR
DSS/CABLE
Sets to TV/VCR mode.
Sets the remote to control some
basic DDS or Cable box functions.
MUTE
FM
Mutes the sound instantly.
Receives FM radio signal.
CHANNEL UP/DOWN
VOLUME UP/DOWN
Selects a channel.
Adjusts volume.
SURROUND
Creates a deeper, 3-D sound effect.
RAPID TUNE
NUMBER Keys
Displays the last channel
you were watching.
Selects a channel directly.
ADD/DELETE/CLEAR
ANGLE
Adds or deletes a channel.
Cancels an item on the screen.
Selects the desired angle
in DVD mode.
SUB TITLE
AUDIO
Selects the desired audio mode.
TITLE
Selects the desired title by number
on some DVDs.
SELECT
Controls navigation around
on-screen menu.
Selects a different subtitle language.
DISPLAY/ENTER
Displays the TV status and clock.
In DVD mode, displays disc and
unit information.
In DSS or CABLE mode, it may be
necessary after channel selection.
MENU
ACTION
Displays DVD menu.
Displays Main Menu.
PROGRAM
SET
Displays SET PROGRAM screen.
You can set Timer Program and
On-Timer.
Sets a selected menu.
REW/SLOWRewinds tape and searches reverse
scene. Decreases slow motion
speed in Still mode.
FF/SLOW+
Fast forwards tape and forward
visual search. Increases slow
motion speed in Still mode.
STILL/PAUSE
Pauses picture in Play mode and
frame advance picture in Still mode.
SKIP
/SEARCH
ZOOM/COUNTER RESET
Enlarges specific portions of DVD
picture. Resets to “0:00:00” at
desired portion of tape.
Skips back one chapter or track. Goes to
previous menu screen. Goes directly
to the desired recording. Locates end
point of recording.
REC
PLAY
RETURN/SPEED
Returns to DVD menu screen.
Selects recording speed of tape.
Begins playback.
SKIP
/CM SKIP/ZERO SEARCH
Skips one chapter or track. Goes to next
screen. In Stop mode, goes to the counter
“0:00:00”. In Play mode, skips over 1 to
3 minutes of tape.
8
Records a program.
STOP
Stops recording or playback.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P08-11 Location).p65
8
2002/06/19, 14:51
Initial Setup
Universal Light Tower® Illuminated Remote Control
LIGHT button:
, DSS/CABLE, CH UP/DOWN, VOL UP/DOWN)
When LIGHT is pressed, (DVD,
buttons will light for 5 seconds for easy button location.
If no button is pressed in 5 seconds, the light goes out to conserve the batteries.
EJECT/OPEN/CLOSE button:
When this button is pressed in TV-VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.
Indicators on the Front Panel
REC Indicator
Lights up during recording.
In Rec Pause or OTR
Pause mode, the Indicator
flashes.
Pg. 18
Remote Sensor
ANGLE Indicator
Lights up when a scene
recorded at a different
angles is detected.
(DVD only).
Pg. 49
PROG TIMER Indicator
Lights up when the unit is set for Timer Recording.
It flashes when a Timer Recording has been set
with no tape inserted, the clock is not set,
or the tape is in motion.
Pg. 30
Lights up when the On Timer is set.
Pg. 26
9
DM2092 (P08-11 Location).p65
9
2002/06/19, 14:51
Location of Controls (continued)
Front View of the unit
Built In Speaker (✕ 2)
If the disc cannot be removed,
First unplug unit.
Then, prepare a rigid wire (e.g. an
extended paper clip, etc.) and, applying
moderate force, insert it straight into the
hole at the base of the tray. The tray will
eject a little. Now, pull the tray all the way
out and remove the disc.
Cassette Compartment
Disc Tray
Phones Jack
Connect an earphone
or headphones.
REC (See page 8.)
FAST FORWARD/SEARCH
(See page 8.)
Audio/Video Input Connector
Connect from other component.
PLAY/REPEAT
(See page 8.)
POWER (See page 8.)
REWIND/SEARCH
(See page 8.)
STOP (See page 8.)
STOP/EJECT (See page 8.)
PAUSE (See page 8.)
TV/FM (See page 8.)
PLAY (See page 8.)
SKIP
(See page 8.)
SKIP
(See page 8.)
CHANNEL UP/DOWN
TRACKING UP/DOWN
(See page 8.)
VOLUME UP/DOWN (See page 8.)
OPEN/CLOSE (See page 8.)
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P08-11 Location).p65
10
2002/06/19, 14:51
Initial Setup
Rear View of the unit
VHF/UHF Antenna
Input Terminal
See below.
Audio Output
Connector (L/R)
Pg. 12
AC Power Plug
When plugged into an AC outlet,
this unit consumes 3.5 W of
electric power in OFF condition.
Optical digital audio
output connector
Pg. 13
Connections
For ANT./Cable
Connect the cable from
Antenna/Cable to the VHF/UHF
terminal on the unit.
IN from
ANT./CABLE
VHF/UHF
VHF/UHF
For DSS/Cable Box
Connect the OUT jack on your
cable box to the VHF/UHF
terminal on the unit with a RF
cable.
Cable TV
Converter Box
IN from
ANT./CABLE
VHF/UHF
WARNING
Overtightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
VHF/UHF
11
DM2092 (P08-11 Location).p65
11
2002/06/19, 14:52
Connections (continued)
Audio connections
Ready Checklist
■ Unit ➛ Amplifier ➛ Speaker
Unit
Turn down the volume, then turn this unit, as well
as other equipment to be connected, off before
proceeding with connection.
Do not block ventilation holes of any equipment
and arrange them so that air can circulate freely.
Read through the instructions before connecting
other equipment.
Ensure that you observe the color coding when
connecting audio and video cables.
Enjoying digital audio output from the
digital audio output connector
AUDIO OUT
R L
Amplifier
R
L
AUDIO IN
Speaker
Speaker
Notes on audio output from the optical digital
audio output connector
Sound
Optical digital audio
Disc recording
output from connector
format
Dolby Digital bitstream
or OFF (no
Dolby Digital (1-5.1 ch)
output)*1
DVD Linear PCM Linear PCM (2ch)
(48/96 kHz
(48 kHz sampling/16 bit
16/20/24 bit) only)*2 or no output*1
dts
Bitstream or no output*1
Video
PCM
MPEG 1
(44.1 kHz sampling)
CD
Linear PCM
CD
Linear PCM (44.1 kHz sampling)
Linear PCM
M P 3 MP3
(It depends on the MP3 file)
*1 The type of audio output from the connector can be
selected by the Settings for DVD Operation. (See page 59.)
*2 Sound having 96 kHz sampling is converted into 48 kHz
sampling when it is output from the unit’s optical digital
audio output connector.
For your reference:
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished
Works. © 1992-1997 Dolby Laboratories,
Inc. All rights reserved.
12
• Dolby Digital is a digital sound compression
technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel
surround sound, as well as stereo (2-channel)
sound, this technique enables a large quantity of
sound data to be efficiently recorded on a disc.
• Linear PCM is a signal recording format used in CDs.
While CDs are recorded in 44.1 kHz/16 bit, DVDs are
recorded in 48 kHz/16 bit up to 96 kHz/24 bit.
• If you have a Dolby Pro Logic Surround decoder,
you will obtain the full benefit of Pro Logic from the
same DVD movies that provide full 5.1 channel
Dolby Digital soundtracks, as well as from titles with
the Dolby Surround mark. For information on
Panasonic or Technics Dolby Pro Logic Surround
Sound Decoders please contact your local dealer.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P12-13) connect.p65
12
2002/06/19, 14:52
or
Unit ➛ dts (digital theater systems) Decoder ➛ Amplifier ➛ Speaker
When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts
bitstream is output from the unit Optical digital audio output connector. When the unit is
connected to a Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio
in your home. [An optical digital audio cable (optional) is required when an optional Dolby
Digital decoder or dts decoder is used.]
Notes on connecting an Optical
digital audio cable (optional)
Unit
• Firmly connect the cable to the
connector.
Optical digital audio
cable (optional)
Dolby Digital Decorder/
dts processing (optional)
IMPORTANT NOTE:
Caution for optical digital audio
output connector:
• When connecting an amplifier (with
an Optical digital input connector)
which does not contain the Dolby
Digital or dts decoder, be sure to
select “OFF” at “Dolby Digital” and
“OFF” at “dts” of the Settings for
DVD Operation “AUDIO OUTPUT”
(see page 59). Otherwise, any
attempt to play DVDs may cause
such a high level of noise that it
may be harmful to your ears and
damage your speakers.
• When a dts decoder is connected,
please select “Bitstream” at “dts” of
the Settings for DVD Operation
“AUDIO OUTPUT”. If “OFF” is
selected, there will be no sound.
(See page 59).
• Video CDs and CDs can be played
as normal.
Note:
• Some dts decoders which do not
support DVD-dts Interface may not
work properly with the unit.
Amplifier
Center speaker
Front
Speaker
Front
Speaker
Subwoofer
Surround
speaker
Surround
speaker
13
DM2092 (P12-13) connect.p65
13
2002/06/19, 14:52
Initial Setup
■ Unit ➛ Dolby Digital Decoder ➛ Amplifier ➛ Speaker
Initial Setup (Ready to Play)
Please make all cable or antenna connections before powering on.
Initial Setup (Ready to Play)
Press
1
2
on the remote for TV-VCR mode.
Plug the unit power cord into an AC wall outlet.
Press POWER* on the remote or unit. The unit
comes on and auto channel and clock set starts.
CH AUTO SET PROCEEDING
POWER
TV-VCR
• If you use a cable box, turn it on and set it to the Public
Broadcasting Service (PBS) channel in your time zone.
If you use a DSS receiver, it must be turned off.
SELECT
AUTO CLOCK SET
SET
PROCEEDING
ACTION
CANCEL : PRESS STOP KEY
3
Settings are made automatically.
When setup is done, this screen appears.
2 / 6 / 2002 WEDDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
If AUTO CLOCK SET IS INCOMPLETE
screen appears, set the clock using MANUAL
CLOCK SET procedure on next page.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P14-15)Initial setup.p65
14
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
Reset all unit Memory Functions
If AUTO CLOCK SET was incomplete,
manually set the clock as follows.
1
Press ACTION on the Remote to
display SET CLOCK Menu screen.
When moving unit to a new location, or if a
mistake was made in the Initial Setup section.
• Make sure a tape is not inserted in the unit.
SET CLOCK
DST : ON
SELE CT MONTH
SELECT :
SET
: SET
END
: ACT I ON
2
Press
to select the month
and press SET to set. In the
same manner, select and set
the date, year, time, and DST.
(Daylight Saving Time)
the unit
1 Turn
Power on.
and hold both PLAY and FF
2 Press
on the unit for more than 5 seconds.
• The power will shut off.
• Please ignore “NO CASSETTE” warning.
3 Perform “Initial Setup” on page 14.
3
Press ACTION twice to start
CLOCK and exit.
Note to CABLE system installer:
This reminder is provided to call the CABLE (Cable TV) System Installers attention
to Article 820-40 of the NEC that provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
15
DM2092 (P14-15)Initial setup.p65
15
2002/06/19, 14:52
Initial Setup
Manual Clock Set
button on the remote
Reset Language, Channels, Clock,
1
LOCK LANGUAGE
53
TV
to display MAIN MENU.
1
CH
CLOCK
SELECT :
END
: ACT I ON
2
Press ACTION*
M A I N MENU
DVD
Time Z
SET : SET
Clock
Channels
Language
1) Press
select “CH.”
1) Press
to select
language icon.
to
1) Press
to
select “CLOCK.”
M A I N MENU
M A I N MENU
M A I N MENU
DVD
DVD
53
TV
SELECT :
END
: ACT I ON
TV
1
2) Press SET.
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
MENU PRINCIPAL
HOLA
SELECT :
SET
: SET
END
: ACT I ON
BLOQUEO IDIOMA
5
TV
3
1
CANAL
RELOJ
3) Press
to select
“ANTENNA,” then
press SET to set
your antenna system
(“TV” or “CABLE”).
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
For Spanish
MENU
BONJOUR
DVD
BLOCAGE LANGUE
TELE
HORLOGE CANAL
53
SEL. :
FIN
to select
4) Press
“AUTO SET,” then
press SET.
1
REGLER : SET
: ACT I ON
• After Channel Auto Set
is finished, Clock Auto
Set will be performed.
(If clock is set manually,
Clock Auto Set will not
be performed.)
For French
M A I N MENU
DVD
HELLO
LOCK LANGUAGE
53
TV
1
CH
CLOCK
SELECT :
END
: ACT I ON
1
CH
CLOCK
SELECT :
END
: ACT I ON
SET : SET
2) Press SET.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
: SET
: ACT I ON
END
(“TIME ZONE ADJUST”
appears only when
auto clock is set.)
3) Press
to select
“MANUAL,” then
press SET.
(For Auto Clock Set,
select “AUTO CLOCK
SET,” and press SET.)
SET CLOCK
2 / 6/2002 WED 12: 00PM
DST : ON
SELE CT HOUR
SELECT :
SET
: SET
END
: ACT I ON
BACK :
<Example MANUAL
CLOCK SET screen>
SET : SET
For English
3) Press ACTION
to exit.
16
SET : SET
53
TV
SET : SET
2) Press SET
repeatedly.
DVD
LOCK LANGUAGE
DVD
1
CH
CLOCK
SELECT :
END
: ACT I ON
CH
CLOCK
LOCK LANGUAGE
53
LOCK LANGUAGE
Continued on
the next page.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P16-17 lang ch clk).p65
16
2002/06/19, 14:52
*Important: If a remote control button does not work
when pressed, press the
button on
the remote and try the button again.
Time Zone Adjust
Initial Setup
Time Zone Adjust
4) Press
and
press SET to select
and set the month,
date, year, time, and
DST (Daylight Saving
Time).
(Only when Auto Clock is set.)
NUMBER
keys
1) Press
to
select “CLOCK.”
ADD/DLT
M A I N MENU
DVD
53
To Make Corrections,
repeatedly press
to move to error, then
correct.
TV
SELECT
LOCK LANGUAGE
SET
CH
CLOCK
SELECT :
END
: ACT I ON
1
SET : SET
ACTION
2) Press SET.
5) Press ACTION twice
to start the clock
and exit this mode.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
:
END
: ACT I ON
3) Press
to select
“TIME ZONE
ADJUST” and
press or to
subtract or add
hour(s) as
necessary.
Add or Delete a Channel
To add channel:
Select channel with number
keys and press ADD/DLT.
CHANNEL 08 ADDED
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
SET
:
END
: ACT I ON
4) Press ACTION
twice to exit.
• “TIME ZONE ADJUST”
returns to “0” if clock is
set manually.
To delete channel:
Select channel with CH
or number keys and press
ADD/DLT.
CHANNEL 08 DELE TED
17
DM2092 (P16-17 lang ch clk).p65
17
2002/06/19, 14:52
Playback a Tape
Ready Checklist
All connections are made.
Your unit is plugged in.
1
Insert a tape.
• The unit power comes
on automatically.
Record
tab
To prevent tape jam,
remove loose or peeling
labels from tapes.
2
Record On a Tape
1
2
3
Insert a tape with record tab.
• The unit power comes on automatically.
Press CH
or number keys to
Select Channel.
• For “LINE” input, see bottom of next page.
Press SPEED to select recording
speed (see page 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Selected speed is displayed.
Press PLAY* to play a tape.
• If tape has no record tab (see page 4),
auto play begins.
■ Forward/Reverse scene search
➛ Press FF/SLOW+ or REW/SLOW-.
➛ Press again or PLAY to release.
■ Still (Freeze) picture
➛ Press STILL/PAUSE.
➛ Press PLAY to release.
■ Slow Motion picture
➛ Press FF/SLOW+ (increases speed) or
REW/SLOW- (decreases speed) in
Still mode.
➛ Press PLAY to release.
■ Frame by Frame picture
➛ Press STILL/PAUSE in Still mode.
➛ Press PLAY to release.
Notes
• These features work best in SP or SLP mode.
• After the unit is in Still or Slow mode for 3
minutes, it will switch to Stop mode automatically
to protect the tape and the video head.
■ Stop ➛ Press STOP
■ Rewind tape ➛ Press REW/SLOWin Stop mode
■ Fast forward tape ➛ Press FF/SLOW+
in Stop mode
■ Eject tape ➛ Press EJECT on the remote
or STOP/EJECT on the unit
4
Press REC to start recording.
• To edit out unwanted portions, press
STILL/PAUSE to pause and resume
recording.
• You cannot view another channel during
recording.
■ Stop ➛ Press STOP
■ One Touch Recording (OTR)
Press REC repeatedly
0:30
1:00
Normal Rec
to set the recording
4:00
3:00
2:00
1:30
length (30 min - 4 hours.)
• The unit stops recording at a preset time.
• PROG TIMER Indicator lights on the unit.
Notes
• It is not possible to record from DVD/
Video CD/CD to VHS tape using this unit.
• After the unit has been in Rec Pause mode
for 5 minutes, it will stop automatically to
protect the tape and the video head.
• The remaining recording time of an OTR
can be displayed by pressing DISPLAY.
EJECT
CH
CH
Operation using unit buttons
PLAY/REPEAT
Insert a tape.
REC
CH
NUMBER
keys
SELECT
DISPLAY
SET
PLAY
ACTION
FF/SLOW+
REW/SLOWPress to stop
and/or eject tape.
18
REC Indicator
STOP
STILL/
PAUSE
REC
SPEED
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P18-19) play_rec_copy.p65
18
2002/06/19, 14:52
Copy Your Tapes (Dubbing)
*Important: If a remote control button does not work
when pressed, press the
button on
the remote and try the button again.
Connections you’ll need to make
Recording (Editing) unit
Playing (Source) VCR
R-AUDIO-L VIDEO
IN
MONO
Playback (Source)
1
IN FROM
ANT.
OUT TO
TV
VIDEO IN L-AUDIO IN-R
Basic Operation
OUT
Recording (Editing) unit
Insert blank tape with
record tab.
Insert prerecorded tape.
• Dubbing tapes protected
with Copy Guard will have
poor quality results.
Select “LINE” mode.
See “Selecting Input Mode” below.
2
3
Press PLAY, then
press PAUSE at
starting point to put
in Standby mode.
Press REC, then
press STILL/PAUSE
immediately to put in
Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
5
STOP
Press PLAY
to start dubbing.
Press STILL/PAUSE
to start dubbing.
Press STOP
to stop dubbing.
Press STOP
to stop dubbing.
Selecting Input Mode
Caution
• Unauthorized exchanging and/or
copying of copyrighted recordings
may be copyright infringement.
• Please note that some tapes
cannot be dubbed on this unit.
Also, it is not possible to dub
DVD/Video CD/CD to VHS tape
using this unit.
Method 1:
Press CH
. The display will change as follows.
1
2
3
(CABLE) (TV)
125 or 69
LINE
Method 2:
a Press ACTION for MAIN MENU.
b Press
to select “TV”, then press SET
for SET UP TV screen.
c Press
to select “INPUT SELECT,” and
then press SET to select “TUNER” or “LINE.”
d Press ACTION twice to exit this mode.
19
DM2092 (P18-19) play_rec_copy.p65
19
2002/06/19, 14:52
Basic DVD Operation
Ready Checklist
All connections are made. (See pages 11-13.)
Your unit is plugged in.
If unit is connected to an audio amplifier,
turn the stereo system’s power on.
1
2
Press POWER* on the remote or unit.
Insert a disc.
• If a disc is already inserted, go to step 3.
(Depending on the disc, playback may start
automatically.)
1) Press OPEN/CLOSE.
2) Place disc into disc tray.
• Hold disc by its edges only
(page 7) with printed side up
and use guides to place into
1 tray. Use 1 3”(8 cm) or 2
2 5” (12 cm) disc.
3
Press PLAY to start play.
Disc tray closes automatically.
• You may also close the tray
by pressing OPEN/CLOSE.
• Data reading time differs with
each disc.
CLOSE
READING
<Example>
T I TLE MENU
If an interactive DVD*1 or a
Video CD with playback
control*2 is used and a TITLE
MENU appears, go to step 4.
4
2 Insert disc.
Press
OPEN/CLOSE.
Love r s
B i r ds
Dogs
of the world
Using number key(s)
starts play automatically.
Dogs
3 Press PLAY. 2 • 6
Cas t l es
Press
or
number key(s) (see
below) to select title
and press SET to
play.
T I TLE MENU
Cas t l es
Love r s
Operation using unit buttons
Dogs
B i r ds
<Example>
1 digit number
1 ••• 1
2 digit number
12 ••• 10➛1➛2
3 digit number
123 •••100➛1➛2➛3
Press SKIP
| or |
to go to next or previous menu screen.
• SKIP function not available with all discs.
Please refer to disc jacket for operation information.
To return to MENU (play stops)
Press TITLE, MENU, or RETURN. (DVD)
Press RETURN. (Video CD)
<Example>
1 Press POWER. 5
Press STOP.
*1 Interactive DVD...
May include multiple camera angles, stories, etc.
*2 Video CD with playback control...
Particular scenes or information can be
interactively selected from a menu that
appears on the screen.
20
5
6
Press STOP to stop play.
Press OPEN/CLOSE to eject the disc.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P20-21 Basic DVD).p65
20
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the DVD button on the
remote and try the button again.
■ Forward/Reverse rapid scene search
➛ Press FF/SLOW+ or REW/SLOWduring play.
➛ Press PLAY to release.
• Starting forward/reverse search during play
started from menu on Video CDs may recall menu.
• Search speed, slow at first, increases with each
additional press of the button up to 5 levels.
➛ Press SKIP
| or |
during play.
Each press skips a chapter (DVD) or
track (Video CD/CD).
Pressing |
SKIP once midway through a
chapter/track returns to start of that chapter/
track. Each additional press skips back one
chapter/track.
• Pressing SKIP
| or |
during play started
from menu on Video CDs may recall menu.
RESUME function
The unit memorizes the point where
STOP is pressed ( flashes on screen).
Press PLAY to resume play from this point.
Pressing STOP again or opening the tray
cancels RESUME, however, RESUME is not
canceled when power is turned off and on.
• RESUME works only with discs for which
elapsed play time is displayed during play.
Auto-Power Off function
Power turns off after unit has been in Stop
mode (DVD) for about 5 minutes.
Chapter/Track Chapter/Track Chapter/Track Chapter/Track
Reverse Skip
Forward Skip
Current playback position
■ Still (Pause) Picture
➛ Press STILL/PAUSE during play.
➛ Press PLAY to release.
• DVD/Video CD : The unit will enter Still picture mode.
• CD : The unit will enter Pause mode.
■ Frame by Frame picture (DVD/Video CD)
➛ Press STILL/PAUSE in Still mode.
➛ Press PLAY to release.
• Each press advances picture one frame.
• Hold down for consecutive frame advance.
• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically (see page 60).
■ Slow Motion picture (DVD/Video CD)
➛ Press FF/SLOW+ or REW/SLOW(DVD only) in Still mode.
➛ Press PLAY to release.
• Slow motion speed, slow at first, is increased with
each additional press of the button up to 5 levels.
• Reverse slow motion is not available for video CDs.
Enjoy Video CDs featuring
playback control without using
menus (Video CDs only)
1. Do steps 1-3 (previous page).
When menu appears, press STOP.
2. Press number key(s) to select desired
track (play begins).
• Check disc for track numbers.
• Press “1” to start at beginning of disc.
To Resume Menu use,
Press STOP, and press PLAY, then the menu
appears. Now, go to step 4 (previous page).
Notes
• Please read the disc jacket for operation
information.
• If a single sided disc is placed in upside
down, “PLEASE CHECK THE DISC,
AND FOR STAINS OR SCRATCHES ON
DISC” is displayed.
• Remove disc and press unit POWER off
when not in use.
• Disc continues to rotate with menu
displayed even after play is done. Press
STOP to clear menu display when finished
with menu.
21
DM2092 (P20-21 Basic DVD).p65
21
2002/06/19, 14:52
Basic Operation
■ Forward/Reverse Chapter/Track Skip
• When
appears on the screen while a
button is being pressed, it means that the
corresponding operation is prohibited by
the unit or the disc.
TV Operation
1
*Important: If a remote control button does not work
button on
when pressed, press the
the remote and try the button again.
Press POWER*
on the remote or unit.
2
08
ABC
Ready Checklist
All connections are made. (See page 11).
Your unit is plugged in.
Use CH
or
number keys to
select a channel.
VOL + / VOL POWER
3
Press VOL + or VOL to adjust volume.
PHONES
Jack
24
CH
■ Using the 100 key
When selecting CABLE channels 100 to 125
with the number keys, first press the 100 key,
and then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you
were watching.
■ Audio Mute
Press MUTE to instantly mute the sound.
Press again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or
headphones (not supplied) to the Phones Jack.
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P22 TV).p65
22
2002/06/19, 14:52
MTS Broadcast / TV Stereo System
Receivable Broadcast Types
®
Equipped with
-TV Noise
Reduction for true MTS
®
reproduction.
-TV Noise
Reduction is required for good
stereo separation and audio fidelity.
®
is a registered trademark, and
®
is licensed by
Technology
Licensing.
The following are possible audio broadcast types and
on-screen displays. The signal being received is indicated
with an “ ” mark while the selected audio mode is indicated
with an arrow. To change the audio mode for these
broadcasts, see the “Select Audio Mode for TV Viewing”
section (below.)
Press DISPLAY to display
the broadcast signal being received.
STOP
1 2 : 0 0AM
STEREO
SAP
MONO
1 2 : 0 0AM
STEREO
SAP
MONO
STOP
1 2 : 0 0AM
STEREO
SAP
MONO
STOP
1 2 : 0 0AM
STEREO
SAP
MONO
MTS Stereo broadcast
Multi-channel Television Sound Stereo
broadcast. Select STEREO audio mode.
• If stereo broadcast is weak and the
display flickers, select MONO audio
mode for possible improvement.
ABC
0 : 00 : 00
SP
SAP broadcast
Secondary Audio Program
(sub language).
Select SAP audio mode for the sub
language.
ABC
0 : 00 : 00
SP
MONO broadcast
Normal monaural sound broadcast.
ABC
0 : 00 : 00
SP
Audio Mode for TV Viewing
Press AUDIO to select the desired audio mode
as described above.
(Arrow shows selection.)
• Each press of AUDIO will change the audio mode as shown
below.
• “SAP” is selected with first press of AUDIO.
< Example >
STOP
Press AUDIO
1 2 : 0 0AM
STEREO
SAP
MONO
ABC
0 : 00 : 00
SP
STOP
1 2 : 0 0AM
STEREO
SAP
MONO
ABC
0 : 00 : 00
SP
STOP
1 2 : 0 0AM
STEREO
SAP
MONO
ABC
0 : 00 : 00
SP
Press AUDIO
Press AUDIO
23
DM2092 (P23 MTS).p65
23
2002/06/19, 14:52
TV Operation
STOP
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo
(main language) and Secondary Audio
Program (sub language) broadcasts are
being received simultaneously.
Select the STEREO or SAP audio mode.
ABC
0 : 00 : 00
SP
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs,
but also makes useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION*
to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
SELECT :
END
: ACT I ON
3
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SET : SET
SELECT :
: ACT I ON
END
4
1
CH
CLOCK
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: CAP C1
: CAP C1
SELECT :
SET
: SET
END
: ACT I ON
OFF
1)Press
to
select “TV.”
2)Press SET to
display SET UP
TV screen.
1) Press
to
select “CAPTION”.
2) Press SET
to display
CAPTION screen.
1) Press
to
select CAPTION
MODE.
2) Press SET
repeatedly to select
mode. (See left.)
CAP C1
TEXT C2
TEXT C1
CAP C2
5
Press ACTION three times
to return to the normal screen.
Recording and Playing Back a Closed Caption/
Text Program
Record : Record normally. Closed Caption/
Text signal, if present, is recorded
automatically.
Playback : Start playback. Perform above steps
to select desired caption mode.
24
Closed Caption Mode Selections
Caption Mode: CAP C1 or C2
A narration of selected TV
programs is displayed.
Check TV program listings for CC
(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
Most of the screen will be blocked
out. When the TV station
broadcasts information, such as
program listings, it will appear in
this space.
Caption Mode: OFF
Closed Caption /Text narration will
not be displayed.
NOTE :
The closed caption or text signal may
be broadcast over C1, C2, or both.
Also, text contents can vary so you
may wish to try different settings.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P24-25TV CC).p65
24
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
button on the
Caption On Mute Feature
Closed Caption narration, if available, is displayed
when MUTE button is pressed for silence.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
SELECT :
END
: ACT I ON
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SET : SET
SELECT :
: ACT I ON
END
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: OFF
: CAP C1
SELECT :
SET
: SET
END
: ACT I ON
5
CAP C1
CAP C2
• When a disc supporting closed caption
is used, the subtitle and the closed
caption may overlap. In this case, turn
the subtitle or caption on mute mode off.
(See page 48.)
1)Press
to
select CAPTION
MODE.
2)Press SET
repeatedly to
select “OFF.”
1) Press
to select
CC ON MUTE.
2) Press SET
repeatedly to select
desired mode.
NO
Note
1) Press
to
select “CAPTION”.
2) Press SET to
display CAPTION
screen.
• Each press of SET will
change the display
as shown left.
• The caption may be
broadcast over CAP
C1 or C2.
6
Press ACTION three times
to return to the normal screen.
7
Press MUTE to mute the sound and
display closed captioning.
• To cancel, press MUTE again.
25
DM2092 (P24-25TV CC).p65
25
2002/06/19, 14:52
TV Operation
3
1
CH
CLOCK
1) Press
to
select “TV.”
2) Press SET to
display SET UP
TV screen.
TV Timer Features
Ready Checklist
ON-TIMER with Alarm
The clock is set to the correct time.
This unit can be set to automatically power on in one of
4 modes (TV, VCR Playback, FM radio, or DVD/Video
CD/CD.) You can also combine the On-Timer with a
one minute alarm that gradually increases in volume.
1
2
Press PROG* to display SET PROGRAM
screen.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
3
1)Press
to select
“ON TIMER.”
2)Press SET to display
ON TIMER screen.
1)Press
to select
desired settings.
2)Press SET to set the
ON-TIMER TIME or
ON-TIMER mode.
ON T I MER
ALARM : ON
SELE CT HOUR
SELECT :
SET
: SET
END
: PROG
• Make sure a tape is inserted
if Playback mode is selected.
• Make sure a disc is inserted
CH02
CH03
CH125
if DVD (DVD/Video CD/CD)
CH01
VCR mode is selected.
• See “FM Radio” on pages 28
FM1
DVD FM9 FM8
and 29 for instructions on
how to preset FM stations.
• ON-TIMER mode
selection order
4
Press
to select
ALARM “ON” or “OFF.”
ON T I MER
ALARM : ON
SELE CT ALARM
CANCEL : ADD / DLT
SELECT :
SET
: SET
END
: PROG
BACK :
When “ON” is selected,
an alarm will gradually increase in volume for one
minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
and
to move back and correct.
use
5
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• PROG TIMER Indicator lights up on the unit.
To Cancel ON-TIMER,
Repeat steps 1 and 2. Then, press ADD/DLT to clear
the time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
26
PROG TIMER Indicator
Sleep Timer
This unit can be set for auto power off.
1
2
Press PROG to display SET
PROGRAM screen.
1) Press
to select
SLEEP
TIMER.
SELECT :
SET
: SET
2) Press SET
END
: PROG
repeatedly
to select
the desired
SLEEP TIMER 30 60 90 00
time.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
To cancel,
press SET repeatedly until 00 appears.
3
Press PROG to return to the
normal screen.
• Pressing DISPLAY with sleep
timer set displays remaining time.
Note
• If no button on the remote or unit
(including a button used to turn off
the alarm) is pressed within 60
minutes after unit turns itself on, it
will turn itself back off.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P26 TV timer).p65
26
2002/06/19, 14:52
On-Screen Display (OSD)
*Important: If a remote control button does not work
when pressed, press the
button on
the remote and try the button again.
TV/VCR Status & Clock Display
Press DISPLAY
to display or remove the overlay.
Channel Caption (See page 38.)
Function Status
Current Time
Rec Time Remaining
(OTR mode only, see
page 18.)
ABC
REC
1 2 : 0 0PM
-0 : 1 2 : 3 4
0 : 25
SP
STEREO
SAP
MONO
Counter
Tape Speed
(See page 4.)
Receivable
Broadcast Types
(See page 23.)
Whenever a blank section of a tape comes up in
Play mode, or when the selected channel has no
broadcast signal with the Weak Signal Display
Feature set to “OFF” (see page 39), the screen will
turn solid blue.
Channel & Function Display
When a function button is pressed (PLAY, FF, etc.)
or you change channels, the unit mode or channel
number will be displayed. (Some station names
may also appear if Channel Caption is set. See
page 38.)
08
PLAY
ABC
27
DM2092 (P27 VCR status ).p65
27
2002/06/19, 14:52
TV Operation
Blue Screen Display
FM Radio
FM Radio is ...
This unit has an FM radio with built-in antenna, 9 station preset, and a band range of
87.5 ~ 108.1 MHz. You can even set the On-Timer (page 26) to wake up to your favorite
radio station.
FM Radio Setup
1
2
3
Press FM on the remote or press TV/FM
on the unitto display FM radio mode.
Press a number
key* (1~9) to
select the FM
preset number.
1 2 : 0 0PM
FM 1
87. 5MHz
1) Press CH
to
select the desired
radio station.
1 2 : 0 0PM
FM 1
8 7. 7MHz
(Each press
changes frequency
by 200 KHz.)
MEMORY : PRESS ADD / DLT KEY
2) Press ADD/DLT
to set the radio
station.
1 2 : 0 0PM
FM 1
TV/FM
8 7. 7MHz
MEMOR I ZED
Hold down CH or
for a few seconds,
then release to quickly
scan for FM stations in
your area.
To Make Corrections,
select station with a
number key, then do
step 3 again.
To exit FM mode,
or DVD
press
on the remote or
TV/FM on the unit.
CH
• To cancel, press CH
or
while in search
mode.
FM Antenna Setup
Make sure FM tuning is done
correctly (see FM Radio Setup).
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
28
1
CH
SET : SET
1)Press
to select “TV.”
2)Press SET
to display SET
UP TV screen.
Continued on next page.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : consumerprod[email protected]
DM2092 (P28-29 FM).p65
28
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the FM button on the remote
and try the button again.
3
1)Press
to
select FM
ANTENNA.
2)Press SET to
select “INT
SET : SET
SELECT :
END
: ACT I ON
(INTERNAL)” or
“EXT
■ For cable TV users (EXTERNAL)” to
➛ “INT”
■ For antenna users determine which
one sounds best.
➛ “EXT”
4
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
Press ACTION twice to end setup.
TV Operation
Using FM Radio
1
2
Press FM on the remote or press TV/FM
on the unitto display FM radio mode.
1 2 : 0 0PM
FM 1
87. 5MHz
Press a number
key (1~9) to
select a preset
FM number
(see FM Radio
Setup on page 28).
Notes
• FM radio cannot be recorded on a
Video cassette.
• You may get better reception by
repositioning the unit.
• You cannot select FM Radio mode
during playback or record, or while a
blue back screen (PROG, ACTION,
MENU) is displayed.
• Once stations are set, the selected
station and current time are displayed
when FM Radio mode is entered.
To remove time, press DISPLAY. If
DISPLAY is pressed again, the unit
status screen appears.
To exit FM mode,
or DVD on the remote
press
or TV/FM on the unit.
Audio Mode for FM Radio
1 2 : 0 0PM
STEREO
MONO
FM 1
8 7. 7MHz
Press AUDIO
repeatedly to select
“STEREO” or “MONO”
in FM Radio mode.
29
DM2092 (P28-29 FM).p65
29
2002/06/19, 14:52
Timer Recording
You can set up to 8 programs to be recorded while
you are away.
1
2
Press PROG* to display SET
PROGRAM screen.
TIMER PROGRAMMING.
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
2) Press SET to
display screen.
SELECT :
SET
: SET
END
: PROG
3
to select
1) Press
SET PROGRAM
Ready Checklist
All connections are made.
Your unit is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
• If a program is already in
memory, press
, and
SET to select an unused
program number.
CH
START
STOP
Press
to select
7 FR I --:-- --:-- -- and SET or
to set
TODAY
SLP
the
recording
DATE.
------------------------
DATE
SELE CT START DATE
SELECT :
SET
: SET
END
: PROG
Example
Today’s
Date
8
7
9
SELECT
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT
= Same time once a week
WEEKLY
(SAT)
2
1
31
/
6
Selection Order
WEEKLY
(MON)
DAILY
WEEKLY
(SUN)
Repeat step 3 to set:
• Start time, stop time
• Channel (or LINE for outside source)
• Speed (SP, LP, SLP)
4
P
1
2
3
4
DT
day
----
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00a
-- : --- : --- : --
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER : SET
END
: PROG
CH SPD
08 SP
-- --- --- --
PROG TIMER Indicator
Press PROG to end
the program.
To Enter More
Programs,
press
to select
and SET to set a blank
program number, and
then repeat step 3.
5
Press PROG twice to exit this mode.
30
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
• If you’re using a cable box, make sure that it
is tuned to the desired channel and the power
is left on for timer recording.
• PROG TIMER Indicator lights up on the unit.
DM2092 (P30-31 Timer Rec).p65
30
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
button on the remote
Cancel a Timer Recording:
(Recording is in progress)
Review, Replace or Clear Program
Contents : (Recording is not in progress)
Hold down STOP for a few seconds
to cancel the Timer Recording.
1
2
• Any future daily or weekly recordings
will be performed as programmed.
Repeat steps 1 and 2 on page 30.
Press
to select
the desired program.
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER : SET
END
: PROG
3
To Replace program...
START
STOP
CH
1) Press SET to display.
8 SAT 9:00P 12:00A 08 2) Press
to select
TODAY
SLP
and
press
SET
or
-----------------------SELE CT START DATE
to
set
new
SELECT :
SET
: SET
BACK :
program contents.
END
: PROG
3) Press PROG.
DATE
P
1
2
3
4
DT START STOP CH
-- -- : -- -- : -- -8 10 : 00p 12 : 00a 125
10 8 : 00p 9 : 00p 10
SU 9 : 00p 10 : 00p L
SPD
-SP
SP
LP
Timer Operation
To Clear program...
Press ADD/DLT.
SELECT 1 - 8 :
ENTER : SET
END
: PROG
4
Press PROG twice to exit this mode.
Notes
• 2 minutes before Timer recording is performed,
“PLEASE PREPARE FOR TIMER REC” appears and/or
the PROG TIMER Indicator flashes.
Be sure
a cassette with record tab is loaded and the unit is in
Stop mode.
• If the start times of two programs overlap, the lower
numbered program will have priority.
• If the start time for a Timer Recording comes up during
a normal recording or One Touch Recording (page 18),
the Timer Recording will not be performed.
• If there is a power interruption of more than one minute,
the recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been
set, check all entries and make necessary corrections.
31
DM2092 (P30-31 Timer Rec).p65
31
2002/06/19, 14:52
Cable Box Universal Remote Control Feature
Universal Remote Control is...
The Remote Control may be set up to control some
basic DSS or Cable box functions.
The Universal Remote Control Setup
1
Find your DSS box or Cable box
Brand Code Number from one of
the charts on the next page.
2
Setup remote.
Hold down DSS CABLE and press
number keys to enter code.
• If code number is 100 or greater,
e.g., press 1 - 0 - 2 for 102.
3
Confirm code entry.
Press POWER* to turn selected unit
ON or OFF.
• See below for controllable functions in each
mode.
Notes
• Please repeat the Universal Remote Control Setup
after replacing remote control batteries.
• The remote control will not operate all DSS receivers
or Cable Boxes made by the manufacturers listed.
If you get no results, your particular brand cannot be
controlled.
Using the Universal Remote Control
(Available Buttons / Functions)
Once the remote control has been properly set up,
you can select TV-VCR, FM, DVD, DSS or CABLE
mode depending on which functions you wish to
control.
Press
, FM, DVD or DSS CABLE on the
remote control to select the desired mode. (See below
for buttons available in each mode.)
Set to
, FM, DVD:
All TV functions, as well as functions of TV-VCR, FM,
or DVD.
Set to DSS CABLE:
• Basic VCR functions, e.g. PLAY, REC, etc.
• CABLE/DSS function, e.g. POWER, ENTER,
NUMBER keys (except 100 key), CH UP/DOWN.
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P32-33 Univ rem).p65
32
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
the remote and try the button again.
, DVD, FM button on
DSS Brand Code Numbers
Toshiba ........................................................... 90
Hitachi/ Hughes ........................................ 91, 99
Primestar ........................................................ 92
Drake .............................................................. 93
Magnavox ................................................. 94, 95
Uniden ....................................................... 94, 95
Optimus .................................................... 94, 95
Panasonic ....................................................... 96
ProScan .......................................................... 97
RCA ................................................................ 97
SONY ...................................................... 98, 105
Cable Box Brand Code Numbers
Oak Sigma ................................. 46, 11, 129, 101
Panasonic .............................. 17, 16, 08, 87, 109
Philips ................. 23, 24, 20, 13, 07, 50, 128, 129
Pioneer ................................................ 06, 05, 12
Pulsar ................. 04, 42, 63, 44, 30, 52, 124, 126
Quest .................................................. 06, 05, 12
Radio Shack ........................... 44, 51, 75, 59, 126
RCA ....................................... 17, 16, 08, 87, 109
Realistic .................................. 44, 51, 75, 59, 126
Recoton .................................. 44, 51, 75, 59, 126
Regal .............. 41, 14, 15, 28, 102, 104, 103, 130
Regency ............................................ 28, 29, 130
Rembrandt ... 44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung .................................. 42, 06, 32, 05, 40
Scientific Atlanta ................. 08, 09, 25, 61, 53, 87
Sheritech ......................................................... 27
Signal ...................................................... 26, 112
SL Marx .......... 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ................................... 17, 16, 08, 87, 109
Standard Components ........... 32, 39, 42, 44, 126
Stargate ........... 04, 42, 32, 40, 63, 44, 30, 52, 06,
124, 126
Sylvania ..................................................... 19, 18
Teknika ...................................................... 74, 35
Telecaption .............................................. 77, 127
Teleview ............................. 40, 19, 38, 32, 42, 06
Texscan ..................................................... 19, 18
Tocom .............................. 34, 33, 01, 42, 66, 120
Toshiba ........................................................... 36
Unika ........................ 44, 42, 63, 29, 01, 126, 120
Universal .......................... 52, 43, 44, 63, 42, 126
Viewstar ............... 62, 40, 22, 13, 58, 20, 26, 107
Videoway ...................................... 07, 23, 50, 129
Vidtek .............................................................. 64
Zenith ........................................... 07, 23, 50, 129
Notes
• In DSS or CABLE mode, it may be necessary to press ENTER after pressing number
keys for channel selection.
• In DSS or CABLE mode, POWER, CH Up/Down, Number Keys, ACTION, PROG,
DISPLAY/ENTER, SEARCH/SKIP-, R-TUNE, SELECT, SET, CM SKIP/ZERO/SKIP+,
COUNTER RESET/ZOOM, ANGLE, AUDIO, TITLE, SUB TITLE, MENU, or ADD/DLT are
not available. Press , FM, DVD to use these functions.
• Depending on your DSS receiver or Cable box brand, some of the functions listed may not
be remote controllable.
• Some DSS receiver or Cable box brands require you to turn on the power manually.
• Due to changes in infra-red commands used by manufacturers, some brands
have several codes. If your unit does not respond to the first code, please try the next one.
33
DM2092 (P32-33 Univ rem).p65
33
2002/06/19, 14:52
Advanced Operation
Archer ....................... 44, 06, 01, 120, 05, 63, 126
Cableview ...... 29, 09, 01, 63, 120, 44, 42, 30, 52,
04, 124, 126
Citizen ................ 44, 52, 30, 63, 42, 04, 124, 126
Curtis ................................. 08, 09, 25, 61, 53, 87
Century .................................. 44, 51, 75, 59, 126
Cabletenna ............... 29, 09, 01, 63, 120, 44, 126
Cable Cinema ........... 29, 09, 01, 63, 120, 44, 126
Diamond ................... 29, 09, 01, 63, 120, 44, 126
Eagle .................... 62, 40, 22, 13, 58, 20, 26, 107
Eastern .............................................. 28, 29, 130
Explorer ............................. 08, 09, 25, 61, 53, 87
Gemini ............................................... 30, 04, 124
General Electric ................................. 01, 57, 120
General Instruments .... 01, 84, 83, 34, 03, 02, 04,
55, 65, 66, 67, 68, 120, 106, 121, 122, 115, 117,
118, 124
Gerrard .......................................... 44, 51, 75, 59
GC Electronics ............. 44, 42, 63, 29, 30, 52, 04,
124, 126
Hamlin ............ 41, 14, 15, 28, 102, 104, 103, 130
Hitachi ............................................................. 31
Jerrold ........ 01, 84, 83, 34, 03, 02, 04, 55, 65, 66,
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ................................................. 30, 04, 124
Macom ............................................................ 31
Magnavox ................................................ 26, 112
Matsushita ............................. 17, 16, 08, 87, 109
Movietime ................... 32, 39, 42, 44, 126, 38, 40
Maestro ..................................................... 74, 35
NEC .............................................. 40, 19, 38, 32
NSC .............................................. 40, 19, 38, 32
Novavision ......................... 08, 09, 25, 61, 53, 87
Next Level ............. 01, 84, 83, 34, 03, 02, 04, 55,
65, 66, 67, 68, 120, 106, 121, 122
Oak ........................................... 46, 11, 129, 101
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape.
When timer recordings are made, program index and information are also included.
These index marks can be used to access or scan recordings.
Index Search
Go directly to the desired recording.
1
Press SEARCH* in
Playback or Stop
mode to display
INDEX SEARCH
screen, and then
press number keys
to select the
recording number.
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
NEXT : SEARCH
EX I T : STOP
• To calculate
number, see below.
Press FF or REW to
start search.
2
Play begins at
search end.
To search forward
or back 1 index,
press FF or REW
while screen left is
displayed (10
seconds).
I NDEX SEARCH
FORWARD SEARCH : FF
REVERSE SEARCH : REW
REW
FF
To cancel, press PLAY or STOP.
■ To calculate the Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
2
3
4
5
6
7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
2
3
4
5
6
7
NOTE: indicates start points of each recording.
34
Notes
• Make each entry within 10 seconds,
or the Index Search mode will be
canceled.
• If Index Search is started very close
to an index mark, that index mark
may not be counted in the search.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P34-37 tape OP).p65
34
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
button on the remote
Program End Search
Locates end point of recording for continuity.
1
2
Press SEARCH twice in Playback or
Stop mode to display PROGRAM
END SEARCH screen .
Press FF
to start search.
PROGRAM END SEARCH
To cancel,
press PLAY or STOP.
SEARCH START : FF
EX I T : SEARCH
Example of Program End Search operation.
Fig.1
PLAYBACK DIRECTION
INDEX
Program 1
Press SEARCH button
FF
Program 2 or BLANK
End Point
Fig.2
BLANK
INDEX
Program 1
Program 2
Press SEARCH button
BLANK
End Point
FF
Fig.3 If search exceeds a few seconds in BLANK area.
Press SEARCH button
BLANK
INDEX
Program 1
Program 2
FF
End Point
Advanced Operation
Upon locating end point...
The unit searches slightly past end point,
reverse searches, and plays the last few
seconds of the program, then stops.
Press SEARCH button
Note
• If Program End Search is started very close
to an index mark, that mark may be
skipped over.
35
DM2092 (P34-37 tape OP).p65
35
2002/06/19, 14:52
Tape Operation (continued)
Repeat Play
Set to see a recording over and over.
PLAY
REPEAT ON
To turn “ON,”
press PLAY/REPEAT on the unit
repeatedly in Play mode to select
“REPEAT ON”.
To turn “OFF,”
repeat above to select “REPEAT OFF.”
• Playback repeats when tape end is
reached or an unrecorded portion longer
than 30 seconds is detected.
PLAY/REPEAT
Note
• For repeat play in DVD mode, see page 55.
Zero Search
To quickly return to a specific tape counter location.
1
2
Press DISPLAY* during playback
to display the Counter.
3
4
5
Continue playback, rewind, or
fast forward.
36
PLAY 12 : 00 PM
0 : 00 : 00
SLP
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
Press STOP.
Press CM/ZERO in stop mode to
start ZERO SEARCH.
• Unit goes into FF or REW mode and
stops at the last point the Counter was
set to 0:00:00.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P34-37 tape OP).p65
36
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
button on the remote
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV mode (Only when
Weak Signal Display is set to OFF.), DVD
stops, or blank tape is played for 5 minutes
➛ Power turns off
• This feature is canceled if any button is
pressed during above conditions.
■ Auto Playback
Insert a tape in Power off mode
➛ Power turns on
• Playback begins if tape has no record tab.
■ Auto Rewind (except for Recording)
Tape reaches its end
➛ Rewind, ➛ Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
➛ Rewind, ➛ Stop, ➛ Eject
Commercial Skip
By pressing the CM/ZERO button in Playback mode
you can skip over 1 to 3 minutes of recorded tape in
just a few seconds.
Advanced Operation
Press CM/ZERO repeatedly to select skip
time in Playback mode.
• No indication appears.
OFF
1st Press
1 min skip
2nd Press
2 min skip
3rd Press
3 min skip
37
DM2092 (P34-37 tape OP).p65
37
2002/06/19, 14:52
Special VCR Features
Channel Caption is ...
Channel Caption
1
2
Press ACTION*
to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
3
1
CH
CLOCK
SET : SET
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
: SET
: ACT I ON
END
4
CHANNEL CAPT I ON
ABC
CBS
FOX
NBC
-----
PBS
CNN
ESPN
HBO
-----
SELECT :
SET
: SET
END
: ACT I ON
CHANNEL CAPT I ON
PBS
ABC
CNN
CBS
ESPN
FOX
HBO
NBC
CLEAR : ADD / DLT
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to
select “CH.”
2) Press SET to
display SET UP
CHANNEL screen.
Station names, e.g. ABC, CNN, etc.
are set so they will appear when a
channel is selected. Choose 24
preset names.
Ready Checklist
You need a list of stations and
the channel numbers you
receive them on.
1) Press
to select
CHANNEL CAPTION.
2) Press SET to
display screen.
1) Press
to select a
station.
2) Press SET (or ) to
move cursor to the
right.
3) Press
to select
channel number.
4) Press SET (or
) to
set preset captions.
• Repeat step 4 until the
Caption List is complete.
To Make Corrections
Press
number.
Press
5
38
, then SET (or
) to select channel
to change, or ADD/DLT to delete.
Press ACTION three times
to end setup.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P38 CH captioon).p65
38
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
Weak Signal Display Feature
Ready Checklist
It is necessary to enter TV mode by pressing
before selecting “CH” on the MAIN MENU.
Remote Warning Feature
When Universal Remote Control (page 32) is
used, and this feature is set to “ON,” a warning
appears whenever an invalid key is pressed in
DSS or Cable mode.
1
2
DVD
LOCK LANGUAGE
53
TV
1
CH
CLOCK
SELECT :
END
: ACT I ON
3
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT :
END
: ACT I ON
SET : SET
1) Press
to
select “TV.”
2) Press SET to
display SET UP
TV screen.
to
1)Press
select REMOTE
WARNING.
2)Press SET to
set “ON” or
“OFF.”
• “REMOTE WARNING : OFF”
➛ Remote warning will not appear even if
invalid key is pressed.
1
2
Press ACTION twice
to return to normal screen.
Press ACTION
to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
3
1
CH
SET : SET
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to select
“CH.”
2) Press SET to
display SET
UP CHANNEL
screen.
1) Press
to
select WEAK
SIGNAL
DISPLAY.
2) Press SET to
set “ON” or
“OFF.”
Notes
• “ON” = Picture is displayed regardless of
signal condition, and may not
always be clearly visible.
“OFF”= Screen turns solid blue when
signal is absent or weak.
• If unit is connected to equipment which
has blue back feature, selecting “ON” will
have no effect on the other equipment.
4
Press ACTION twice
to return to the normal screen.
VCR Lock
REC
All operations are prohibited except Timer
recording and tape eject. Useful for families
with small children.
In Stop mode, hold
down REC on the
VCR LOCK ACT I VATED
unit without a
cassette inserted
for 7 seconds to
turn “ON.”
VCR LOCK OFF
(Please ignore “NO
CASSETTE”
warning.)
Repeat above with
or without cassette
to turn “OFF.”
• VCR Lock is canceled automatically
after about 24 hours if clock is set.
39
DM2092 (P39 SPECIAL VCR).p65
39
2002/06/19, 14:52
Advanced Operation
4
When “ON” is selected, the picture is displayed even
when a broadcast signal is weak or non-existent.
Press ACTION
to display MAIN MENU.
M A I N MENU
button on the remote
V-Chip Control Feature
V-Chip Control Feature is...
This unit has a built-in V-Chip Control which allows
you to block unwanted TV usage based on US
MOVIES and US TV PROGRAMS Ratings.
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Enter Secret Code
A 4-digit code must be entered to view a blocked
program or change rating settings.
1
2
Press ACTION*
to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
CLOCK
SELECT :
END
: ACT I ON
3
1
CH
SET : SET
LOCK
ENTER 4-D I G I T CODE
-BACK SPACE:
ENTER : 0 - 9
: ACT I ON
END
To Make Corrections
Press repeatedly to
move the cursor.
Press number keys to
make the correction.
4
LOCK
CONF I RM 4-D I G I T CODE
****
****
1) Press
to
select “LOCK.”
2) Press SET to display
LOCK screen.
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE : SET
END
: ACT I ON
1) Press number keys
to enter your secret
code.
2) Enter same code
again for confirmation.
• Step 2) not necessary
when changing rating or
secret code.
• Take care that you are
not observed entering
the secret code.
Press SET to display
US Ratings menu (see
pages 41, 42).
Or
Press ACTION twice
to exit.
Changing your secret code
• You will need your current code.
Do steps 1 ~ 3. In step 4, press CLEAR to clear
current code.
Repeat steps 3 and 4 to enter new code.
40
Notes
• Some rental movies do not
include V-Chip data.
• DO NOT forget your secret code.
• Once ratings are set, restricted
tapes or programs cannot be
accessed unless the secret code
is entered.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P40 V-chip).p65
40
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
If LOCK menu is not displayed, perform
“Enter Secret Code” steps on page 40.
button on the remote
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
US MOVIES Ratings
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
: OFF
DVD LOCK
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1)Press
to select
US MOVIES.
2)Press SET to set
“ON” or “OFF.”
■ “ON” ➛ V-Chip Control is activated.
■ “OFF” ➛ V-Chip Control is deactivated.
Note
• “NEXT PAGE” displays CANADIAN V-Chip
setting menu. Not necessary except when
viewing Canadian tapes or broadcasts.
2
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
3
1)Press
to select
CHANGE
SETTINGS.
2)Press SET to
display screen.
US MOVIES RATINGS
G
GENERAL AUDIENCE:
All ages admitted.
PG
PARENTAL GUIDANCE:
Some material may not be suitable
for children.
PG-13 PARENTS CAUTIONED:
Some material may be
inappropriate for children under 13.
R
NC-17 OVER AGE 17 ONLY:
No one 17 and under admitted.
X
ADULTS ONLY:
Advanced Operation
1)Press
to select
VIEW NR
PROGRAMS?.
2)Press SET to set
“YES” or “NO.”
RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
NR (Not Rated) PROGRAMS
Some movies, such as old movies
or foreign movies usually have no ratings.
4
1) Press
to select
and SET to set
ratings to be
blocked.
(See ratings chart
on this page.)
5
Press ACTION to redisplay LOCK menu
and continue with US TV PROGRAMS
Ratings Setup (page42).
Or, press ACTION four times to exit.
41
DM2092 (P41-43 V-chip).p65
41
2002/06/19, 14:52
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do
“Enter Secret Code” steps on page 40.
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
US TV PROGRAMS Ratings
1
2
3
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
: OFF
DVD LOCK
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1)Press
* to
select US TV
PROGRAMS.
2)Press SET to set
“ON” or “OFF.”
TV-Y7
• “NEXT PAGE” displays CANADIAN V-Chip
setting menu. Not necessary except when
viewing Canadian tapes or broadcasts.
TV-G
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
: OFF
DVD LOCK
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
CONTA I NS NO RAT I NG
SELECT :
SET : SET
END
: ACT I ON
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
FOR ALL CH I LDREN
SELECT :
SET : SET
END
: ACT I ON
Note
You may select from
standard TV ratings
(chart 1), or customize
to a specific content rating
(chart 2).
5
42
TV-Y
■ “ON” ➛ V-Chip Control is activated.
■ “OFF” ➛ V-Chip Control is deactivated.
Note
1)Press
to select
CHANGE
SETTINGS.
2)Press SET to
display screen.
1)Press
to
select VIEW NR
PROGRAMS?.
2)Press SET to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, emergency information
usually have no ratings.
4
US TV PROGRAMS RATINGS:
Chart 1
1)Press
to select
and SET to set
ratings to be
blocked.
(See ratings charts
on this page.)
TV-PG
TV-14
TV-MA
FOR ALL CHILDREN:
Content specifically geared to
young viewers ages 2-6.
FOR AGE 7 AND OLDER:
May contain mild physical or
comedic violence which may
frighten children under 7.
GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language,
and more intense violence.
MATURE AUDIENCE:
May contain mature themes,
profane language, graphic violence,
and sexual situations.
US TV PROGRAMS RATINGS:
Chart 2
FV
V
S
L
D
Fantasy Violence
Violence
Sexual Situations
Adult Language
Sexually Suggestive Dialogue
• Ratings highlighted in
green will be blocked.
Ratings in white letters
will not be blocked.
Press ACTION four times
to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P41-43 V-chip).p65
42
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
button on the remote
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
<When V-Chip Control is activated>
• If a program or movie
ABC
exceeds the ratings you
have set, a message
PROGRAM RAT I NG EXCEEDED
will appear on a black
RAT I NG : PG-1 3
background and sound
ACCESS CODE
---is muted.
ENTER : 0-9
To View a Blocked Program/Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in
the Blocking Message screen.
• V-Chip Control is reactivated when power is
turned off or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-4 page 40).
Then, set US MOVIES and/or US TV
and SET.
PROGRAMS to “OFF” using
(Ratings set on pages 41 and 42 is retained
and will be in effect when V-Chip Control is
activated again.)
Advanced Operation
43
DM2092 (P41-43 V-chip).p65
43
2002/06/19, 14:52
Audio Features
Audio Mode for Playback
With the proper audio mode
setting, your unit can:
• record and playback MTS stereo
broadcast (main language) in
stereo Hi-Fi. Stereo sound is
See the “Playback a Tape” section on
recorded on the left and right
page 18 to playback the tape.
audio tracks and on the video
portion of a tape.
• record and playback a monaural
Press AUDIO repeatedly broadcast (main language) or
(each press within 5 seconds)
H I F I ( L/R)
SAP (Secondary Audio Program,
H I F I ( L)
to select desired mode.
H I F I ( R)
usually in a second language) on
NORMAL
• Select “HIFI (L/R)”, “HIFI (L)”
the Hi-Fi tracks for better quality
or “HIFI (R)” to listen to
monaural sound.
stereo recordings in stereo
sound. Select “NORMAL” for • playback non-Hi-Fi tapes in
• This screen appears when
monaural sound.
monaural.
you press AUDIO during
Choose the type of sound track for playback.
1
2
playback.
Audio Mode for Recording
Choose audio mode to match recording type.
1
Press AUDIO repeatedly to select the audio
mode according to the type of broadcast to
be recorded.
• The Audio mode selected stays in effect until it is
changed.
2
See the “Record On a Tape” section on
page 18 to do a recording.
Notes
• Only tapes recorded in Hi-Fi stereo will playback with
true stereo sound. Standard stereo tapes will playback
with monaural sound.
• To listen to Hi-Fi stereo playback, the unit AUDIO (L/R)
jacks must be connected to a stereo amp and speakers.
• There may be a difference in audio level between Hi-Fi
and normal audio playback.
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P44-45 Audio).p65
44
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
button on the remote
DVD Volume Adjust
Audio recorded on a DVD or Video CD often
incorporates a dynamic range of sound.
This means that, when compared to a music CD,
etc., the average volume is generally lower and the
peaks may be higher. This unit can be set so that
the volume is increased automatically.
1
2
Press ACTION*
to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
3
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT :
END
: ACT I ON
4
1
CH
CLOCK
1)Press
to
select “TV.”
2)Press SET to display
SET UP TV screen.
1)Press
to select
DVD VOL ADJUST.
2)Press SET to set the
level (0, +1, or +2).
SET : SET
Press ACTION twice to return to the normal
screen.
Surround Sound System
Set Surround sound.
SURROUND ON
SURROUND OFF
Press SURROUND.
•“SURROUND ON”
is displayed.
To Cancel,
press SURROUND.
Notes
• Surround sound effect is not available for normal
(mono) broadcasts.
• The surround effect (TV, VCR mode only) is not
output to Audio Output L/R Connector.
45
DM2092 (P44-45 Audio).p65
45
2002/06/19, 14:52
Advanced Operation
You can hear a deeper, 3-D sound effect using just
the unit’s two front speakers.
Video / Audio Menu
*Important: If a remote control button does not work
when pressed, press the
button on
the remote and try the button again.
This feature allows easy setting of picture and sound suitable for each program source.
Video Menu
1
2
Audio Menu
Press ACTION* to display MAIN
MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
SELECT :
END
: ACT I ON
3
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT :
: ACT I ON
END
4
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
Do steps 1 - 3 left.
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
c
1) Press
to
select “AUDIO
MENU.”
2) Press SET to
select desired
mode. (See
below.)
Press ACTION three times to end
setup.
[Audio Menu]
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
5
1
CH
CLOCK
1) Press
to select “TV.”
2) Press SET to
display SET UP
TV screen.
a
b
1) Press
to
select “VIDEO
MENU.”
2) Press SET
repeatedly to
select desired
mode. (See
below.)
Press ACTION three times to end
setup.
■ NORMAL
■ AUTO
[Audio AGC (Auto Gain Control)]
The sound level is automatically adjusted
to suit the program source (see below left).
■ MOVIE
Sound suited to movies.
■ MUSIC
Sound suited to music. (Factory setting)
■ SPEECH
Sound suited to dialogue.
[Video Menu]
■ NORMAL
Factory setting.
■ MOVIE
Picture is adjusted for a movie-like feel.
■ NIGHT
Color and picture intensity are adjusted
to be easier on the eyes for night
viewing.
Volume level
High
Standard
TV
Volume level
High
CD
TV
Low
Standard
TV
TV
Low
AUDIO MENU : NORMAL
AUDIO MENU : AUTO
<Audio AGC Example>
46
Notes
CD
• The effects of this feature on the signal is not
output to the Audio/Video Output Connector.
• When AUDIO MENU mode is “AUTO,” the
AUDIO ADJUST setting will be “STANDARD.”
• AUDIO MENU settings remain in memory.
• VIDEO MENU settings do not remain in memory.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P46-47 A-V Menu).p65
46
2002/06/19, 14:52
Video / Audio Adjustment
Video Adjustment
1
2
Press ACTION to display MAIN
MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT :
: ACT I ON
END
4
1
CH
CLOCK
SELECT :
END
: ACT I ON
3
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
5
Audio Adjustment
V I DEO ADJUST
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
STANDARD
SELECT :
ADJUST :
END
: ACT I ON
1) Press
to select “TV.”
2) Press SET to
display SET UP
TV screen.
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
1) Press
to
select “VIDEO
ADJUST.”
2) Press SET to
display.
1) Press
to
select an item.
(See below.)
to
2) Press
adjust.
6
Press ACTION four times to end
setup.
[VIDEO Adjustment]
Press ACTION to display MAIN
MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
c
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
FM ANTENNA
: I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT :
: ACT I ON
END
d
1
CH
CLOCK
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
e
AUDIO ADJUST
BASS
TREBLE
BALANCE
STANDARD
SELECT :
ADJUST :
END
: ACT I ON
1) Press
to select “TV.”
2) Press SET to
display SET UP
TV screen.
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
1) Press
to
select “AUDIO
ADJUST.”
2) Press SET to
display.
to
1) Press
select an item.
(See below.)
to
2) Press
adjust.
To Reset AUDIO Controls.
and SET to select and set
Press
“STANDARD.” All controls return to their
factory settings.
f
Press ACTION four times to end
setup.
[AUDIO Adjustment]
■ COLOR Control
Adjust color intensity.
■ TINT Control
Adjust for natural flesh tones.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by adjusting both
contrast and color level in the proper
balance.
■ SHARPNESS Control
Adjust picture sharpness.
■ BASS Control
To adjust the intensity of low frequency
sound.
■ TREBLE Control
To adjust the intensity of high frequency
sound.
■ BALANCE Control
To adjust the (L/R) unit speaker output
level.
• The levels set here do not affect other
audio equipment when connected to the
Audio Output L/R Connector.
47
DM2092 (P46-47 A-V Menu).p65
47
2002/06/19, 14:52
Advanced Operation
To Reset VIDEO Controls.
and SET to select and set
Press
“STANDARD.” All controls return to their
factory settings.
a
b
Disc Operation
Subtitle Language (DVD only)
You can select a different subtitle language
(if offered) than the one set at the Settings for DVD
Operation. (See page 58.)
1
Press SUB TITLE*
in Play mode to display
the subtitle selection
on-screen.
2
Te amo
Ready Checklist
Please read “Basic DVD Operation”
on page 20.
[Subtitle language (No.)]
[Audio soundtrack language (No.)]
ENG
English
• Display disappears after 5
seconds.
• When no subtitles are offered,
“-” will be displayed instead of
the language number.
FRA
French
DEU
German
ITA
Italian
ESP
Spanish
1) Press
to select
desired language.
2) Press (or ) to set.
3) Press (or ) to
select “ON” or “OFF.”
NLD
Dutch
SVE
Swedish
NOR
Norwegian
DAN
Danish
POR
Portuguese
RUS
Russian
JPN
Japanese
CHI
Chinese
KOR
Korean
MAL
Malay
VIE
Vietnamese
THA
Thai
Number of subtitle language being played back.
Notes
• When closed captioning is used along with subtitles, they may
overlap. If so, turn one function off. (See pages 24 and 25.)
• If after several presses of the button the language does not
change, language selection is not offered on the disc.
• Subtitles may not change to the selected language immediately.
• When power is turned on again or disc is removed, subtitles
revert to initial setting language. If the initial language is not
recorded on the disc, the disc’s priority language will appear.
Audio Soundtrack Language (DVD only)
You can change the audio soundtrack language,
selected at the Settings for DVD Operation, to a
different language if available. (See page 58.)
(This operation works only with discs on which
multiple audio soundtrack languages are recorded.)
a
AUDIO: 1 ENG
Dolby Digital 3/2.1ch
Hello
SELECT :
b
AUDIO: 3 ESP
Dolby Digital 3/2.1ch
• Display disappears after 5
seconds.
Audio attribute 1 type, sampling
frequency, bit No. of the disc.
1) Press
to select
desired language.
Hola
SELECT :
48
SET : SET
Press AUDIO in Play
mode to display the audio
selection on-screen.
SET : SET
Number of the audio
soundtrack language being
played back.
∗
Other
• Change the No. by pressing
and press SET.
,
[Audio attribute 1 type,
sampling frequency, bit No. of
the disc (see page 59)]
16bit
20bit
24bit
1ch - 5.1ch
1ch - 5.1ch
96KHz
or
48KHz
LPCM
Dolby Digital
dts
Linear PCM disc
Dolby Digital disc
dts disc
Notes
• If, after several presses of the AUDIO
button the language does not change,
language selection is not offered on the disc.
• When power is turned on again or disc is
removed, language reverts to initial setting.
If this language is not recorded on the disc,
the language recorded will be heard.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P48-50)Disc OP.p65
48
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the DVD button on the remote
and try the button again.
When
appears on the screen
while a button is being pressed,
it means that the corresponding
operation is prohibited by the unit
or the disc.
Multiple Angle Viewing (DVD only)
DVDs may contain scenes shot from multiple camera
angles allowing the same scene to be viewed at
different angles. You can view these angles,
if available, using the ANGLE button.
1
Press ANGLE in Play
mode to display the angle
selection on-screen.
• Display disappears after 5
seconds.
2
1) Press
to select the
desired angle.
ANGLE Indicator
Notes
Number of angle being played back.
• ANGLE Indicator lights up on the
unit when a scene recorded at
different angles is detected.
• The angle number can be set
beforehand so that the angle is
switched whenever ANGLE
Indicator lights up.
Vocal selection for Karaoke discs (DVD/Video CD)
a
b
Press AUDIO in Play mode to display the
audio screen.
1) Press
(or
) to
select as shown below.
2) Press (or ) to set.
(DVD only)
• Video CD
LR
L
R
Picture Zoom (DVD only)
You can enlarge specific portions of a picture and
select the zoom ratio using the ZOOM button on the
remote during DVD playback.
Notes
• Closed captioning will not be
displayed while Picture Zoom is
used. To see subtitles, set the
subtitle feature to ON (see page 48).
• The subtitle cannot be enlarged nor
can it’s position be changed.
• The picture zoom feature does not
work with a Video CD.
• During picture zoom, “ZOOM1” or
“ZOOM2” is displayed on-screen.
• Zooming, on some discs, may
result in poor picture quality, or may
not operate at all.
Set Zoom size.
Press ZOOM repeatedly to change display as follows.
• You can enlarge the center portion of the image to one of 2
magnifications.
X 1.0 (ORIGINAL)
X 1.5 (ZOOM 1)
1st press
Hello!
X 2.0 (ZOOM 2)
2nd press
Hello!
ZOOM 1
Hello!
ZOOM 2
3rd press
■ Use the , , and
down, left and right.
buttons to move the position up,
49
DM2092 (P48-50)Disc OP.p65
49
2002/06/19, 14:52
Advanced Operation
• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
• DVD Karaoke (2 vocals) VOCAL V1 + V2 VOCAL V1 VOCAL V2 VOCAL OFF
Disc Operation (continued)
Title menu (DVD only)
Some DVDs have more than one title, e.g. movies.
If the disc offers a title menu, you can select the
desired title number. (Operation may vary
according to the disc.)
1
Press TITLE* in Play
mode to display title
Cas t l es screen.
T I TLE MENU
Dogs
B i r ds
Love r s
<Example>
2
T I TLE MENU
Dogs
Cas t l es
Love r s
B i r ds
B i rds
of the world
• Pressing TITLE again
resumes play from the
scene when TITLE was
first pressed.
1) Press
or
number key(s) to
select a title.
2) Press SET or
PLAY to start play.
• Step 2) not necessary
when using number
key(s).
<Example>
DVD menu (DVD only)
DVDs may offer a special menu. This menu may
include guides to unique contents, audio/subtitle
languages, etc. Although contents and operation
may vary, the following steps show basic steps for
using the menu.
a
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
<Example>
b
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
<Example>
Press MENU in Play
mode to display DVD
menu.
• Pressing MENU again
resumes play from the
scene when MENU was
first pressed.
1) Press
or
number key(s) to
select an item.
2) Press SET or
PLAY to access.
• Step 2) not necessary
when using number key(s).
Repeat step “b” if there is
more than one menu.
50
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P48-50)Disc OP.p65
50
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
and try the button again.
Program Play (Video CD/CD)
You can program specific tracks and order of play.
1
2
Press ACTION in Stop mode to display
MAIN MENU.
M A I N MENU
1) Press
to
select “DVD.”
LOCK LANGUAGE
DVD
2) Press SET to
53
display screen.
CH
TV
CLOCK
1
SELECT :
END
: ACT I ON
3
SET : SET
1) Press
to select
“PLAY MODE.”
2) Press SET to
display screen.
DVD MAIN MENU
SELECT
SET
END
4
5
1
2
3
4
5
1) Press
to select
“PROGRAM PLAY.”
2) Press SET to
display screen.
:
: SET
: ACTION
PROGRAM PLAY
DISC
PROGRAM
6 11 16
5 8
7 12 17
15 6
8 13 18
1 13
9 14 19
3 2
10 15 20
2
CLEAR LAST
CLEAR ALL
SELECT
:
SET
: SET
END
: ACTION
START
1) Press
to
select a track
number.
(Track numbers on
disc are displayed.)
2) Press SET to set.
6
.
Program Repeat Play
(Video CD/CD)
a
b
Do steps 1 through 6 on
this page.
Press DISPLAY to display
Disc Information screen.
(Disc Information Screen)
TRACK
PBC
: 1
: OFF
VIDEO CD
1 : 35 : 12
PROGRAM PLAY
DISC
PROGRAM
11 16
5 8
12 17
15 6
13 18
1 13
14 19
3 2
15 20
2
CLEAR LAST
CLEAR ALL
SELECT
:
SET
: SET
END
: ACTION
START
Notes
1) Press
to
select “START.”
2) Press SET to start
play of programs in the
sequence selected.
SET
c
d
Press SET to enter Select mode.
(“REPEAT OFF” will flash.)
(Unit Information Screen)
: SET
END : DISPLAY
Press
to select “DISC
REPEAT.”
(Unit Information Screen)
PLAY
DISC REPEAT
PROGRAM PLAY
• To cancel, press STOP
during play, then press
CLEAR.
• Up to 15 tracks can be programmed.
• “ ” or “ ” (depending on disc) indicates additional
PROGRAM PLAY screen. Press
for next or
previous screen.
• To clear the last program one by one,
to move to “CLEAR LAST” and press
Press
SET. (Pressing CLEAR also clears last program.)
• To clear all programs,
Press
to move to “CLEAR ALL” and press SET.
(Programs are also cleared when the power is turned off or
the disc is removed.)
NEXT : DISPLAY
Press DISPLAY again to
display Unit Information screen.
SET
e
: SET
Advanced Operation
• Repeat step 5 to select another track.
• The selected track is added on the right side.
1 6
2 7
3 8
4 9
5 10
Ready Checklist
Unit is in TV-VCR mode, press
Video CD or CD is inserted.
:
: SET
: ACTION
PLAY MODE
SELECT
SET
END
, DVD button on the remote
SELECT :
SET
: SET
f
END : DISPLAY
Press SET to set mode.
(“DISC REPEAT” stops
flashing.)
To cancel, select “REPEAT
OFF” in step e, then press SET.
51
DM2092 (P51-55)Disc OP2.p65
51
2002/06/19, 14:52
Disc Operation (continued)
*Important: If a remote control button does not work
button on
when pressed, press the
the remote and try the button again.
Random Play (Video CD/CD)
Tracks are played in a random order.
1
2
Press ACTION* in Stop mode to display
MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
3
4
:
: SET
: ACTION
PLAY MODE
SELECT
SET
END
52
SET : SET
DVD MAIN MENU
SELECT
SET
END
:
: SET
: ACTION
1
CH
CLOCK
1) Press
to select “DVD.”
2) Press SET to
display screen.
1) Press
to select
“PLAY MODE.”
2) Press SET to
display screen.
1) Press
to select
“RANDOM PLAY.”
2) Press SET to begin
random play.
• To cancel, press STOP
during play, then press
CLEAR.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P51-55)Disc OP2.p65
52
2002/06/19, 14:52
ntrol button does not work
button on
, press the
d try the button again.
DVD Operation using On-Screen Displays
When DISPLAY is pressed, On-Screen Displays
show disc information (title/chapter/track number,
elapsed playing time) and unit information (Repeat
play, Play mode).
1
Ready Checklist
Unit is in DVD mode, press DVD.
Press DISPLAY in Play or Stop mode to
display “On-Screen Display.”
• Each press of DISPLAY changes the on-screen
display as follows. (Please refer to page 54 or 55.)
Selected disc information
➛
Selected unit information
➛
Normal Screen
Note
• DISPLAY button does not function while DVD
TITLE MENU is displayed.
2
3
1) Press
(or
) to select an item.
2) Press SET to set.
1) Press
to select the setting.
2) Press SET to set.
<Example of DVD>
T I TLE
: 12
CHAPTER : 11
DVD
0 : 12 : 34
T I TLE
: 12
CHAPTER : 24
NEXT : DISPLAY
SELECT :
SET
: SET
NEXT : DISPLAY
To make corrections,
and SET
press
repeatedly to move to
error, then correct.
<Example of Video CD>
TRACK
PBC
: 12
: OFF
TRACK
PBC
SET
: 17
: OFF
: SET
SET
VIDEO CD
0 : 12 : 34
VIDEO CD
0 : 12 : 34
To return to the
normal screen,
press CLEAR or
DISPLAY repeatedly.
NEXT : DISPLAY
: SET
• Pressing is effective
for elapsing time
instead of the above
buttons. Press
repeatedly to delete
the error, then correct.
NEXT : DISPLAY
Notes
• When DISPLAY is pressed
during playback of a Video
CD with Playback control, the
NUMBER keys are not
available on the displayed
screen. In this case, press
DISPLAY again to remove
the displayed screen.
appears on the
• When
screen while a button is being
pressed, it means that the
corresponding operation is
prohibited by the unit or the
disc.
53
DM2092 (P51-55)Disc OP2.p65
53
2002/06/19, 14:52
Advanced Operation
SELECT :
SET
: SET
DVD
0 : 12 : 34
• For some functions the
setting will be
registered immediately
without pressing SET.
• When numbers are
displayed (e.g. title
number), the NUMBER
keys are also available.
DVD Operation using On-Screen Displays (continued)
Detailed Descriptions of Each On-Screen Display
Disc information screen (for DVD)
1. TITLE No.
• Change the No. by pressing
keys, and press SET.
* or the NUMBER
1
2
T I TLE
: 1
CHAPTER : 12
DVD
1 : 12 : 55
3
4
2. Chapter No.
• Change the No. by pressing
keys, and press SET.
or the NUMBER
SELECT :
SET
: SET
3. Disc currently being played
4. Elapsed playing time
NEXT : DISPLAY
The screen may be changed by selecting the
elapsed time.
• Change the elapsed time by pressing NUMBER
keys, and press SET.
(e.g.) 01 : 23 : 45
0➛1➛2➛3➛4➛5
• This function does not work with some discs.
Disc information screen (for Video CD/ CD)
A. Track No.
• Change the No. by pressing
keys, and press SET.
or the NUMBER
A
B
TRACK
PBC
: 1
: OFF
VIDEO CD
1 : 35 : 12
C
D
B. Playback control ON/OFF
[Video CD with playback control only]
ON Video CD menu play is displayed.
OFF Video CD menu play is cleared.
SET
: SET
NEXT : DISPLAY
C. Disc currently being played
Video CD
CD
D. Elapsed playing time
Notes
• Track No. and elapsed playing time are not
displayed during play started from menu of Video
CDs with playback control.
• When
appears on the screen while a button is
being pressed, it means that the corresponding
operation is prohibited by the unit or the disc.
54
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P51-55)Disc OP2.p65
54
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the DVD button on the remote
and try the button again.
Detailed Descriptions of Each On-Screen Display
Unit information screen
• Change the desired mode during play by pressing
, and press SET.
a. Repeat Play
DVD
CHAPTER REPEAT
Video CD/CD TRACK REPEAT
TITLE REPEAT
DISC REPEAT
REPEAT OFF
REPEAT OFF
PLAY
CHAPTER REPEAT
a
SELECT :
SET
: SET
END : DISPLAY
b. Play mode [Video CD/ CD only] (See page 51 or 52.)
PROGRAM PLAY
RANDOM PLAY
-----
program play
random play
normal play
PLAY
DISC REPEAT
RANDOM PLAY
b
: SET
END : DISPLAY
PLAY
For your CURRENT
reference
• CHAPTER/TITLE REPEAT PLAY (DVD)
CURRENT PLAYBACK POSITION
• TRACK/DISC REPEAT PLAY (Video CD/CD)
CURRENT PLAYBACK POSITION
track
track
TRACK REPEAT
TITLE
chapter
track
chapter
chapter
DISC REPEAT
NORMAL PLAY
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
Note
• For repeat play in VCR mode, see page 36.
55
DM2092 (P51-55)Disc OP2.p65
55
2002/06/19, 14:52
Advanced Operation
SET
MP3 Playback Operation
MP3 Playback
You can use this unit to play MP3 format audio recorded for
personal use with a computer etc. onto a CD-R or CD-RW.
Play may not be possible in some cases due to the
condition of the recording.
■ MP3 playback (During STOP mode)
1) Press
to select an MP3 file ( ).
2) Press SET or PLAY to start playback.
1
2
3
■ Select folder (During STOP mode)
1) Press
to select a folder ( ).
2) Press SET to display files/folders
contained in the folder.
Press POWER* on the remote or unit.
Press OPEN/CLOSE,
and then place an MP3 disc into the disc tray.
Press OPEN/CLOSE to close.
MP3 MENU is displayed and playback is
started automatically. (The MP3 CD directory is
displayed.)
Counter
Function
Status
<Example>
PLAY
ROOT
VA
TECHNO
POPS
JAZZ
Folder area
(The currently
displayed folder
turns green)
MP3 MENU
00 : 00 : 00
..
END_WALTZ
DD_CUB I C
NOCTURNE
NORN
Parent
folder
File area
(The selected
MP3 file/folder
is displayed
with a cursor.)
PLAY MODE : NORMAL
<Example>
PLAY MODE
ROOT
: MP3 file
: Folder
: Parent folder
VA
END_WALTZ
DD_CUB I C
NOCTURNE
NORN
TECHNO
POPS
JAZZ
(The MP3 CD directory structure
displayed in the above example OSD is
shown in the diagram at left.)
■ Forward/Reverse Search
Press FF/SLOW+ or REW/SLOW- during play.
Press PLAY to release.
• Search speed, slow at first, increases with each
additional press of the button up to 4 levels.
■ Forward/Reverse Track Skip
Press SKIP
| or |
SKIP during play.
Each press skips a track.
• If pressed within first 3 seconds of playback, skips to
the previous track. If over 3 seconds, returns to
first track. (|
SKIP only.)
• Only the SKIP
| or |
SKIP button can be used
for track skip selection during playback.
Put unit in Stop mode before performing folder/file
selection (see above right.)
4
5
56
■ Select parent folder (During STOP
mode)
1) Press
to select a folder ( ).
2) Press SET to make changes to
the previous directory display.
Note
• Folder area operation cannot be done.
Only file area operation is possible.
■ Select PLAY MODE (During STOP
mode)
1) Press
to move cursor to
PLAY MODE.
2) Press
to select the desired
PLAY MODE (see below).
[PLAY MODE]
NORMAL:
All MP3 files are selected and
played back one time only.
SINGLE REPEAT:
The selected MP3 file is
played back repeatedly.
FOLDER REPEAT:
The MP3 files contained in
the selected folder are played
back repeatedly.
However, folders below the
selected folder are not played
back.
DISC REPEAT:
All MP3 files are played back
repeatedly.
Press STOP to stop playing.
Press OPEN/CLOSE to eject the disc.
The MP3 MENU is closed automatically.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P56-60 DVD).p65
56
2002/06/19, 14:52
DVD Lock Feature
*Important: If a remote control button does not work when
, DVD button on the
pressed, press the
remote and try the button again.
You can prevent playback of DVDs with a specific rating level which may be unsuitable
for children.
• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you
preset, playback will be prohibited.
Caution
Discs not encoded with a rating level will play even if the jacket states it is for
mature audiences. For these discs, the DVD Lock Ratings will not work.
DVD Lock Ratings (DVD only)
Perform DVD Lock setting in TV mode.
Enter your secret code to display LOCK menu.
(Perform “Enter Secret Code” steps on page 40.)
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
to select
“DVD LOCK.”
2) Press SET to set
“ON” or “OFF.”
■ “ON” ➛ DVD Lock is activated.
■ “OFF” ➛ DVD Lock is deactivated.
2
1
2
3
4
UNLOCKED
5
6
7
8
LOCK ALL
SELECT :
END
: ACT I ON
SET : SET
1) Press
to select
“CHANGE
SETTINGS.”
2) Press SET to display
screen.
1) Press
to
select rating level.
2) Press SET to select
“LOCKED” or
“UNLOCKED.”
LEVEL 1 : LOCK ALL:
Playback of all DVDs, CDs and Video CDs is
prohibited. (Use to prohibit play of mature theme
DVDs not encoded with a rating level.)
LEVEL 2 : DVDs expressly for children can be played back.
LEVEL 3 to 7 :
DVDs for general audiences/children can be
played back. (DVDs with mature content are
prohibited.)
LEVEL 8 : NO LIMIT: (Factory preset)
All DVDs can be played back.
• Ratings which are highlighted in Green will be blocked;
those not highlighted (white letters) will not be blocked.
4
Press ACTION three times to end setup.
<When DVD Lock is activated>
YOUR SELECTION
EXCEEDS THE
,
PLAYER S RATING LIMIT.
DO YOU WANT TO CHANGE THE
LIMIT?
YES
NO
SELECT :
SET
: SET
END : DISPLAY
After DVD Lock is set and a
blocked DVD is played, this
message will appear. The
message may differ depending
on the disc.
To continue viewing a blocked
program for now,
to select “YES” and
Press
SET. Then, enter your 4-digit
secret code. When “NO” is
selected, blocked programs
cannot be viewed.
To change DVD LOCK settings
After entering your secret code in
step 3 on page 40, select “OFF”
to deactivate DVD Lock or
change the rating level.
57
DM2092 (P56-60 DVD).p65
57
2002/06/19, 14:52
Advanced Operation
3
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
Settings for DVD Operation
1
2
Press ACTION* in Stop mode to display
MAIN MENU.
DVD
LOCK LANGUAGE
53
TV
1
CH
CLOCK
SELECT :
END
: ACT I ON
3
1) Press
to
select “DVD.”
2) Press SET to
display screen.
M A I N MENU
SET : SET
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: Letterbox
SELECT
SET
END
Once initial settings are done, they
remain in memory (even after the
power is off) until changed.
This means the unit will always
operate under the same conditions
(especially DVDs) each time.
Ready Checklist
Unit is in TV-VCR mode, press
.
1) Press
to select
an item.
2) Press SET to set.
:
: SET
: ACTION
DISC LANGUAGES (See below.)
Any languages offered on the disc can be set. If a
language not offered is set, the original disc language will
be selected.
AUDIO OUTPUT (See page 59.)
You can set the audio output that comes from the digital
audio output terminal.
STILL MODE (See page 60.)
To select “FIELD” or “FRAME” to prevent jitter or to make
small text or fine patterns clearly visible in a still picture.
When “AUTO” is set, “FIELD” or “FRAME” is selected
automatically.
TV MODE (See page 60.)
To select whether the video material for a wide-screen will
be played back in Pan & Scan style or in Letterbox style.
DISC LANGUAGES (DVD only)
To select and set the language of the audio soundtrack,
subtitles, or title/DVD menus for all discs to be played.
4
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: Letterbox
SELECT
SET
END
5
SELECT
SET
END
6
58
:
: SET
: ACTION
DISC LANGUAGES
AUDIO
SUBT I TLE
MENUS
1) Press
to select
“DISC LANGUAGES.”
2) Press SET to display
screen.
: English
: AUTO
: English
:
: SET
: ACTION
“AUDIO” selections
To select the audio soundtrack language.
(factory preset: English)
English/Spanish/French/Japanese
Original: Original disc language
OTHER ✱✱✱✱: Other language selection*1
“SUBTITLE” selections
To select the subtitle language.
(Factory preset: AUTO)
AUTO: Same language selected for
“AUDIO”
• If language set for “AUDIO” is
used in playback, subtitles will
not appear.
• If another language is used
during playback, the subtitles
will appear in the language
selected at “AUDIO” setup.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*1
“MENUS” selections
to select
1) Press
an item.
2) Press SET
repeatedly for
desired language.
(Please refer right.)
Press ACTION to redisplay DVD menu
and go to step 3 to setup another item.
Or, press ACTION three times to exit.
(factory preset: English)
To select the language used in title
menus or DVD menus.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*1
To enter OTHER ✱✱✱✱ code number,
Press number keys (Please refer to
language codes on page 61).
To make corrections, press
repeatedly to delete language code
number, and correct.
*1 If the selected language is not offered,
the original disc language is selected.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P56-60 DVD).p65
58
2002/06/19, 14:52
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
, DVD button on the
AUDIO OUTPUT
Select the digital output to be output from the
optical digital audio output connector of the unit.
1
2
Do steps 1 and 2 on page 58.
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: F I ELD
TV MODE
: Letterbox
SELECT
SET
END
3
:
: SET
: ACTION
AUDIO OUTPUT
LPCM(DVD)
Dolby Digital
dts
DRC
SURROUND
SELECT
SET
END
1) Press
to select
“AUDIO OUTPUT.”
2) Press SET to
display screen.
: OFF
: Bitstream
: OFF
: OFF
: OFF
:
: SET
: ACTION
1) Press
to select
an item.
2) Press SET
repeatedly for output.
(See below.)
■ “LPCM (DVD)” selections
OFF: Linear PCM of less than 48 kHz/16 bit is output.
When playing DVDs recorded in linear PCM of
over 48 kHz/20 bit or 96 kHz, no digital audio is
output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of
48 kHz/20 bit/24 bit or 96 kHz, digital audio
converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
■ “Dolby Digital” selections
Bitstream:
OFF:
Dolby Digital bitstream (1ch-5.1ch) is
output. (Factory preset)
No output.
■ “dts” selections
Bitstream:
OFF:
dts bitstream is output. (Factory preset)
No output.
■ “DRC (Dynamic Range Compression)” selections
OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this is
useful for late-night listening. [Dolby Digital DVDs
only].
Type of amplifier
to be connected
Recommended setting
LPCM
(DVD)
No amplifier is connected OFF
Dolby
Digital
OFF
OFF
AV amplifier (with digital
audio input connector)
without Dolby Digital/dts
decoder
PCM* 1
OFF*2
OFF*2
AV amplifier including
Dolby Digital decoder
PCM* 1 Bitstream
dts
OFF
AV amplifier including
1
*3
Dolby Digital/dts decoder PCM* Bitstream Bitstream
• Make settings according to amplifier
connected to optical audio output as shown in
above table.
• When a dts decoder is not connected, to enjoy
dts DVD, please select audio output other than
dts on the dts DVD menu screen. Otherwise,
there will be no sound from the unit speakers.
*1 Audio output from unit is converted to 48
kHz/16 bit in addition to audio from digital
audio output.
To enjoy high quality sound at 48 kHz/20 bit /
24 bit or 96 kHz, connect the amplifier or
decoder directly to the audio output
connectors, not to the digital audio output
connector. [Select “OFF” at the “LPCM
(DVD)”.]
*2 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or dts decoder,
be sure to select “OFF”.
If “Bitstream” is selected, starting DVD play
may cause such a high level of noise as to be
harmful to your ears and damage the
speakers.
*3 When a dts decoder is connected, please
select “Bitstream” in “dts”. If “OFF” is
selected, there will be no sound.
■ “SURROUND” selections
4
Or, press ACTION three times to exit.
59
DM2092 (P56-60 DVD).p65
59
2002/06/19, 14:52
For Your Information
Surround Sound creates the effect of sound coming from
non-existent rear speakers even when only connected to
Notes
a 2-channel stereo system.
OFF: No Surround Sound effect. (Factory preset)
• Turn off other surround effects when
ON: Surround Sound effect.
using this surround effect.
• For optimum effect, the distance between
the unit and the listener should be about
Press ACTION to redisplay DVD menu
3 or 4 times the distance between the
and go to step 2 to setup another item.
right and left front speakers.
Settings for DVD Operation (continued)
STILL MODE
Set to reduce jitter in a displayed still picture or a
motion picture.
1
2
*Important:
If a remote control button does not work
when pressed, press the DVD button on
the remote and try the button again.
Do steps 1 and 2 on page 58.
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: F I ELD
TV MODE
: Letterbox
SELECT
SET
END
:
: SET
: ACTION
1) Press
* to select
“STILL MODE.”
2) Press SET
repeatedly for mode.
(See below)
AUTO:
“FIELD” (Field still) or “FRAME” (Frame still) is
automatically selected during the still mode.
(Factory preset)
FIELD: “FIELD” (Field still) is always selected.
This setting will reduce jitter when compared
with “AUTO” on some discs.
FRAME: “FRAME” (Frame still) is always selected.
Some texts and fine patterns will be seen clearly
when compared with “AUTO” on some discs.
3
Press ACTION twice to exit this mode.
Selecting TV MODE
Set the screen display style for widescreen video
material playback.
a
b
Do steps 1 and 2 on page 58.
• Pan & Scan (Factory preset)
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: F I LED
TV MODE
: Letterbox
SELECT
SET
END
:
: SET
: ACTION
1) Press
to select
“TV MODE.”
2) Press SET
repeatedly for mode.
(See below.)
Pan & Scan : Widescreen video data is played in Pan
(Factory preset) & Scan style (left and right of screen is
trimmed.)
• Video data not formatted in Pan & Scan
will play in letterbox style.
Letterbox :
Widescreen video data is played in
Letterbox style (top and bottom of screen
has black margin).
c
60
Example
• Letterbox
Press ACTION twice to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P56-60 DVD).p65
60
2002/06/19, 14:52
Language Code List
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/
or “MENUS” (see page 58).
Code Language
Code Language
Code Language
6565 Afar
7079 Faroese
7678 Lingala
8375 Slovak
6566 Abkhazian
7082 French
7679 Laothian
8376 Slovenian
6570 Afrikaans
7089 Frisian
7684 Lithuanian
8377 Samoan
6577 Ameharic
7165 Irish
7686 Latvian, Lettish
8378 Shona
6582 Arabic
7168 Scots Gaelic
7771 Malagasy
8379 Somali
6583 Assamese
7176 Galician
7773 Maori
8381 Albanian
6588 Aymara
7178 Guarani
7775 Macedonian
8382 Serbian
6590 Azerbaijani
7185 Gujarati
7776 Malayalam
8385 Sundanese
6665 Bashkir
7265 Hausa
7778 Mongolian
8386 Swedish
6669 Byelorussian
7273 Hindi
7779 Moldavian
8387 Swahili
6671 Bulgarian
7282 Croatian
7782 Marathi
8465 Tamil
6672 Bihari
7285 Hungarian
7783 Malay
8469 Telugu
6678 Bengali;Bangla
7289 Armenian
7784 Maltese
8471 Tajik
6679 Tibetan
7365 Interlingua
7789 Burmese
8472 Thai
6682 Breton
7378 Indonesian
7865 Nauru
8473 Tigrinya
6765 Catalan
7383 Icelandic
7869 Nepali
8475 Turkmen
6779 Corsican
7384 Italian
7876 Dutch
8476 Tagalog
6783 Czech
7387 Hebrew
7879 Norwegian
8479 Tonga
6789 Welsh
7465 Japanese
7982 Oriya
8482 Turkish
6865 Danish
7473 Yiddish
8065 Panjabi
8484 Tatar
6869 German
7487 Javanese
8076 Polish
8487 Twi
6890 Bhutani
7565 Georgian
8083 Pashto, Pushto
8575 Ukrainian
6976 Greek
7575 Kazakh
8084 Portuguese
8582 Urdu
6978 English
7576 Greenlandic
8185 Quechua
8590 Uzbek
6979 Esperanto
7577 Cambodian
8277 Rhaeto-Romance
8673 Vietnamese
6983 Spanish
7578 Kannada
8279 Romanian
8679 Volapük
6984 Estonian
7579 Korean
8285 Russian
8779 Wolof
6985 Basque
7583 Kashmiri
8365 Sanskrit
8872 Xhosa
7065 Persian
7585 Kurdish
8368 Sindhi
8979 Yoruba
7073 Finnish
7589 Kirghiz
8372 Serbo-Croatian
9072 Chinese
7074 Fiji
7665 Latin
8373 Singhalese
9085 Zulu
For Your Information
Code Language
61
DM2092 (P61-64 Lang. List-Before).p65
61
2002/06/19, 14:52
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
Correction
No power…
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
Power turns itself off...
• Auto power-off (shut off) occurs after about 5 min. in DVD
mode with no operation, or if there is no broadcast signal in
TV or Playback mode. Turn the power back on. (P. 21, 37)
Monitor
Correction
No picture or sound...
• Make sure your antenna system (TV or CABLE), is
correctly set. (P. 11)
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
Poor picture with normal sound...
• Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls
in the SET UP Video Adjustment. (P. 47)
Poor sound with normal picture...
• Adjust VOLUME control. (P. 22)
Poor TV reception...
• Adjust SHARPNESS and PICTURE controls in the SET UP
Video Adjustment. (P. 47)
No color or poor color...
• Adjust TINT and COLOR controls in the SET UP Video
Adjustment. (P. 47)
Ghost (multiple) images...
• Install a directional antenna.
TV programs cannot be watched...
• Make sure the selected channel is in unit’s memory. (P. 16)
Channel cannot be selected...
• Only the channel begin recorded can be viewed on this unit.
VCR
Correction
TV program cannot be recorded...
• Make sure your antenna system (TV or CABLE), is
correctly set. (P. 11)
• Make sure cassette record tab is intact. (P. 4)
Timer recording cannot be
performed…
• Check that clock is set to current time and date.
• Make sure DSS/CABLE box (if used) is left on and tuned to
channel to be recorded.
• Set recording Start/Stop times correctly. (P. 30, 31)
• Timer recording may not be performed or continued if a
power interruption of more than 1 minute occurs before or
during a Timer Recording, even after power is restored.
No playback picture, or the playback
picture is noisy or contains streaks...
• Adjust TRACKING control in either direction. (P. 6)
• Try Head Cleaning. (P. 6)
VCR cannot be controlled...
• Make sure VCR LOCK is set to off. (P. 39)
Correction
Remote Control
Unit cannot be controlled...
•
•
•
•
•
Aim Remote directly at the remote sensor on the unit. (P. 9)
Avoid any object blocking signal path.
Inspect the remote batteries. (P. 4)
Make sure VCR LOCK is set to off. (P. 39)
Exposing unit remote sensor to direct fluorescent or
outdoor light may cause signal interference.
ACTION, PLAY, SELECT, SET
POWER, etc. buttons cannot be
selected...
•
•
•
•
Press
for TV-VCR mode. (P. 32)
Press DVD for DVD mode. (P. 32)
Press FM for FM mode. (P. 32)
Check remote batteries.
62
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P61-64 Lang. List-Before).p65
62
2002/06/19, 14:52
.
DVD/Video CD/CD
Correction
Play fails to start even when
PLAY is pressed...
• This unit cannot play discs other than DVDs, Video CDs and
CDs.
• The disc may be dirty and require cleaning.
Play starts but then stops
immediately...
• Be sure disc is installed with label side up.
Picture is distorted during rapid
advance or rapid reverse...
• The picture will be somewhat distorted at times: this is normal.
No Forward/Reverse search
play...
• Some discs may have sections which prohibit Forward/
Reverse search. (P. 21)
Play does not start even when
title is selected...
• Confirm the “DVD LOCK” setting. (P. 57)
Audio soundtrack and/or
subtitle language is not the one
selected at the initial settings...
• If the audio soundtrack and/or subtitle language selected at
DVD initial settings does not exist on the disc, it will not be
accessible.
No subtitles...
• Subtitles appear only when available on disc.
• Select “ON” at the “Subtitle language” section (P. 48) to
display subtitles.
Alternative audio soundtrack
(or subtitle) language cannot
be selected...
• Alternative language cannot be selected with discs which do
not contain more than one language.
• For some discs, alternative language cannot be selected with
the AUDIO or SUB TITLE button. Try selecting it from the
DVD menu if available.
Angle cannot be changed...
• This function is dependent on software availability. Even if
disc has multiple angles, they may be recorded for specific
scenes only (ANGLE Indicator on unit lights up). (P. 49)
Miscellaneous
Correction
• Insert the cassette window side up; record tab facing you.
Video cassette cannot be
removed...
• Completely insert Power Plug into an AC outlet.
Eject does not function or
insertion cannot be done...
• Turn the POWER off and then on, and try ejecting or inserting
the tape again.
Video cassette ejects when a
recording is started, or the
power is turned off for timer
recording...
• Make sure cassette record tab is intact. (P. 4)
The disc cannot be removed...
• First, unplug unit. Then, prepare a rigid wire (e.g. an extended
paper clip, etc.) and, applying moderate force, insert it straight
into the hole at the base of the tray. The tray will eject a little.
Now, pull the tray all the way out and remove the disc. (P. 10)
In Stop mode, the VCR motor
(CYLINDER) continues to
rotate...
• To enable Quick Play mechanism, the VCR cylinder will rotate
for about 3 minutes. This reduces response time from Stop to
Play mode and from Play to Rewind Search mode.
63
DM2092 (P61-64 Lang. List-Before).p65
63
2002/06/19, 14:52
For Your Information
Video cassette cannot be
inserted...
Warning and Instruction Displays
These displays will alert you of a missed operation or provide further instructions.
OSD
Caution
Page
PLEASE SET CLOCK BEFORE
PROGRAMMING
If you attempt to set or review a Timer
Recording or set the On-Timer and the
Clock is not set...
16, 17
CHECK CASSETTE RECORD TAB
If you press REC, and a cassette is
inserted with no record tab...
TO CANCEL TIMER REC HOLD DOWN
STOP KEY FOR APPROX 3 SEC
If you press STOP during a Timer
Recording...
31
NO CASSETTE
PLEASE INSERT A CASSETTE
If you press PLAY, FF, REW, or REC
without a cassette inserted...
18
PLEASE PREPARE FOR TIMER REC
VIDEO HEADS MAY NEED CLEANING
PLEASE INSERT HEAD CLEANING
CASSETTE OR REFER TO MANUAL
END: PLAY
VCR LOCK ACTIVATED
PLEASE CHECK THE DISC, AND FOR
STAINS OR SCRATCHES ON DISC
IT IS PROHIBITED TO COPY DVD/
VIDEO CD/CD TO VHS
64
If the unit is not in Stop mode or a
cassette with record tab is not inserted
two minutes before a Timer Recording is
about to begin...
If head cleaning becomes necessary
while playing back a tape...
4, 18
30, 31
6
If you press a function button other than
STOP/EJECT or POWER while the unit is
in VCR Lock mode...
39
If you press PLAY, or the unit reads data
from a stained or scratched disc in DVD
mode. Also, if the type of disc is other
than DVD, Video CD or CD...
7
If you press REC in DVD mode...
18, 19
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P61-64 Lang. List-Before).p65
64
2002/06/19, 14:52
Spanish Quick Use Guide/Guía para rápida consulta
Conexión para Ant./Cable
Conecte Ant./Cable a la entrada de antena
de la TV (VHF/UHF).
VHF/UHF
Ant./Cable
VHF/UHF
Ajuste Manual del Reloj
Conexión para Sistema Digital de
Satelite (DSS)/Convertidor de cable
Conecte la salida del convertidor de cable la
entrada “VFH/UHF” con el RF cable.
Convertidoe de cable
Si el ajuste automático del reloj no se ha
completado, ajuste el reloj manualmente
de la siguiente manera.
1
Presione ACTION en el control
remoto para visualizar la
pantalla del menú RELOJ.
2
Presione ▲▼ para seleccionar
el mes y SET para colocarlo. De
la misma forma, seleccione y
ajuste la fecha, año, hora y DST
(Hora de Verano).
3
Presione dos veces la tecla
ACTION para poner el RELOJ
en marcha y salir.
VHF/UHF
Ant./Cable
VHF/UHF
Conecte por favor todas las conexiones del cable
o de la antena antes de energizar los aparatos.
Realizando Configuración Inicial
Presione
para la modolidad TV-VCR.
Conecte el cable electrico de la unidad en
el enchufe de pared de la CA.
Encienda la TV mediante el
control o directamente en
la unidad. La unidad inicia
CH AUTO SET PROCEEDING
la busqueda de canales y
ajusta el tiempo
automaticamente.
1
2
• Si usa convertidor de cable,
enciendala y seleccione el
Servicio Publico de Canales de
Television (PBS) en su horario
de uso o tiempo de su zona.
Si utiliza receptor DSS este
debe de estar apagado.
Selecciones se realizaran
automaticamente, cuando
la configuracion termine
la pantalla siguiente
aparecera.
Si “AUTO CLOCK SET IS
INCOMPLETE” aparece en
pantalla, coloque el tiempo
usando el procedimiento
manual (MANUAL CLOCK
SET), vealo enseguida.
DM2092 (P65-71 Spanish).p65
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
CLOCK
SELECT :
END
: ACT I ON
1
CH
SET : SET
“RELOJ”.
Presione SET.
AUTO CLOCK SET
PROCEEDING
CANCEL : PRESS STOP KEY
3
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
: SET
: ACT I ON
END
2 / 6 / 2002 WEDDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
4
Presione ▲▼
SET CLOCK
SELE CT HOUR
SELECT :
SET
: SET
END
: ACT I ON
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
Presione ▲▼
para seleccionar
“MANUAL” y
luego presione
SET.
2 / 6/2002 WED 12: 00PM y SET para
DST : ON
COMPLETED
AUTO CLOCK SET
65
ACTION para
1 Presione
visualizar el menú.
Presione ▲▼
2
para seleccionar
BACK :
seleccionar y
ajustar la hora
y la fecha.
ACTION dos veces
5 Presione
para que el reloj comience a
funcionar y salir de este modo.
65
2002/06/19, 14:52
For Your Information
3
Ajustar de nuevo el reloj
Spanish Quick Use Guide/Guía para rápida consulta
Operaciones básicas para la
reproducción (VCR)
1
2
Inserte un cassette.
• El videograbador combinado se enciende
automáticamente.
Presione PLAY.
• La reproducción comienza
automáticamente si el cassette no tiene la
lengüeta para prevención de grabación.
■ Para encontrar una escena en particular
Búsqueda hacia adelante ➛ Presione FF/SLOW+
Búsqueda hacia atrás ➛ Presione REW/SLOW■ Para ver una imagen fija (congelada) ➛
Presione STILL/PAUSE
■ Para ver en cámara lenta ➛ Presione FF/SLOW+
o REW/SLOW- en el modo de imagen fija
■ Para ver imágenes cuadro a cuadro ➛
Presione STILL/PAUSE en el modo de imagen fija
■ Para parar ➛ Presione STOP
■ Para rebobinar la cinta ➛ Presione REW/SLOW■ Para hacer avanzar la cinta rápidamente ➛
Presione FF/SLOW+
■ Para expulsar el cassette ➛ Presione EJECT en
el control remoto o STOP/EJECT en el
videograbador combinado
Grabación con temporizador
1
2
Presione PROG para visualizar
“FIJAR PROGRAMACION.”
F I JAR PROGRAMAC I ON
TEMPOR l ZADOR
ENCENDIDO AUTOMATICO
TEMPOR l ZADOR - DORMIR : 00
ELEG l R :
F I JAR : SET
TERM l NAR : PROG
1) Presione ▲▼ para
seleccionar
“TEMPORIZADOR.”
2) Presione SET para
visualizar.
• Si ya existe un programa en la memoria,
presione ▲▼ y SET para seleccionar un
número de programa sin usar.
3
FECHA
INICIO
PARADA
CA
Presione ▲▼ para
7 VIE --:-- --:-- -- seleccionar y
SLP
HOY
-----------------------ELEGIR FECHA DE INICIO
ELEG l R :
F I JAR : SET
TERM l NAR : PROG
presione SET o
para colocar.
• 1-31 = Grabación única
• DIARIO = a la misma
hora de lunes a viernes
• SEMANAL = a la misma
hora una vez a la
semana
Fecha
de hoy
Operaciones básicas para la grabación
1
Inserte un cassette con la lengüeta
para prevención de grabado.
2
3
Presione CH ▲▼ o las teclas
numéricas para seleccionar el canal.
4
• El videograbador combinado se enciende
automáticamente.
Repita el paso 3 para ajustar:
hora de comienzo, hora de parada, canal (o LINEA
para una fuente exterior), velocidad (SP, LP, SLP)
4
Presione SPEED para seleccionar la
velocidad de grabación.
Presione REC para comenzar la
grabación.
■ Para parar ➛ Presione STOP.
■ Si se desea que el videograbador
deje de grabar a una hora prefijada.
(Grabación de un toque)
Presione REC repetidamente para ajustar
la hora de grabación (30 min - 4 horas.)
66
FE I N I C PARADA
D I 9 : 00p 12 : 00a
-- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
CANCELAR : ADD/DLT
ELEG I R 1-8 :
ENTRAR : SET
TERM I NAR : PROG
SP = reproducción normal
LP = reproducción larga
SLP = reproducción super larga
• La velocidad seleccionada debe aparecer
en la pantalla.
• Para no editar ó grabar partes de una
grabación, presione STILL/PAUSE para
hacer una pausa durante la grabación.
• No podrá ver otro canal durante la grabación.
P
1
2
3
4
5
CA VEL
08 SP
-- --- --- --
Presione PROG
para terminar el
programa.
Para introducir más
programas,
presione ▲▼ y SET
para seleccionar el
número de programa
en blanco, y luego
repita los pasos 3.
Presione PROG dos veces para salir
de este modo.
• Si está usando un decodificador de TV
cable, asegúrese que se encuentra en el
canal deseado y que la alimentación
queda conectada para grabar con
temporizador.
• El indicador PROG TIMER se enciende
en el videograbador combinado.
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
DM2092 (P65-71 Spanish).p65
66
2002/06/19, 14:52
Operaciones básicas del DVD
1
2
Presione POWER en el control remoto
o el aparato y luego el boton DVD.
Introducir un disco.
1) Presione OPEN/CLOSE.
2) Ponga un disco en la bandeja de disco.
• Sujete el disco sin tocar ninguna de sus
superficies, póngalo con el lado donde esté
impreso el título hacia arriba, alinéelo con las
guías y póngalo en su posición apropiada.
Disco de 3”(8 cm)
Disco de 5” (12 cm)
3
4
Presione PLAY para Iniciar la reproducción.
La bandeja del disco se cierra automáticamente.
• Si está usando un DVD interactivo (Interactive
DVD) o un Vídeo CD con contol de reproducción
(playback control) y aparece un menú de títulos
(TITLE MENU) en la pantalla, siga al paso 4.
1) Presione ▲▼
o las teclas
numéricas para seleccionar el artículo
deseado.
2) Presione SET para la reproducción.
Si usa las teclas numéricas, la reproducción
comienza automáticamente.
5
6
Presione STOP para parar la
reproducción.
Presione OPEN/CLOSE para expulsar
el disco.
Cambio del idioma de subtítulos
[DVD solamente]
EI idioma de los subtítulos seleccionado al hacer
las fijaciones iniciales se puede cambiar por otro
idioma diferente, si éste se encuentra disponible.
1
SUBTITULO : 1 ENG ACTIVO
2
FIJAR : SET
SUBTITULO : 3 ESP ACTIVO
Te amo
ELEGIR :
FIJAR : SET
DM2092 (P65-71 Spanish).p65
• Cuando no haya
subtítulos grabados, “-”
se visualizará en lugar del
número de idioma.
1)Presione ▲▼ para
seleccionar el idioma
deseado.
2)Presione (o ) para
ajustar.
3)Presione ▲ (o ▼ ) para
seleccionar “ACTIVO” o
“INACTIVO.”
67
Búsqueda hacia adelante
Presione FF/SLOW+ en el modo de
reproducción.
Búsqueda hacia atrás
Presione FF/SLOW- en el modo de
reproducción. (Para liberar, presione PLAY)
■ Para saltar un capítulo o una pista
Salto hacia adelante
Presione SKIP
l en el modo de
reproducción. Un capítulo (DVD) o una
pista (Vídeo CD/CD) se salta cada ves
que se oprime la tecla.
Salto hacia atrás
Presione l
SKIP en el modo de
reproducción.
■ Para ver una imagen fija
Presione PAUSE durante la reproducción.
(Para liberar, presione PLAY)
■ Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione STILL/PAUSE en el modo de
imagen fija.
La imagen avanza un cuadro cada vez
que presiona la tecla. (Para volver a la
reproducción normal, presione PLAY.)
■ Para ver en cámara lenta
(DVD/Vídeo CD)
Presione FF/SLOW+ o FF/SLOW- en el
modo de imagen fija.
(Para liberar, presione PLAY)
Cambio del idioma de la pista de
sonido [DVD solamente]
EI idioma de la pista de sonido seleccionado
al hacer las fijaciones iniciales se puede
cambiar por otro idioma diferente, si éste se
encuentra disponible.
1
SONIDO: 1 ENG
Dolby Digital 3/2.1ch
Hello
ELEGIR :
2
FIJAR : SET
SONIDO: 3 ESP
Dolby Digital 3/2.1ch
Hola
ELEGIR :
Presione AUDIO
durante la
reproducción
para visualizar la
pantalla AUDIO.
Presione ▲▼
para seleccionar el
idioma deseado.
FIJAR : SET
67
2002/06/19, 14:52
For Your Information
I love you
ELEGIR :
Presione SUBTITLE
durante la reproducción.
■ Para buscar una escena en particular
Spanish Quick Use Guide/Guía para rápida consulta
Visión desde otro ángulo [DVD solamente]
Algunos discos DVD tienen escenas que han sido filmadas
simultáneamente desde un número de ángulos diferentes.
Con estos discos, la misma escena podrá verse desde cada
uno de estos ángulos diferentes utilizando el botón ANGLE.
1
ELEGIR :
2
Presione ANGLE durante la
reproducción para visualizar
la pantalla de ángulo.
ANGULO: 1
Algunos discos con películas, por
ejemplo, vienen con dos o más títulos. Si
el disco tiene un menú de títulos
grabados, el botón TITLE podrá utilizarse
para seleccionar el título de la película.
1
FIJAR : SET
Presione ▲▼ para
seleccionar el ángulo
deseado.
ANGULO: 2
ELEGIR :
Utilización de un menú de
títulos [DVD solamente]
2
FIJAR : SET
ELEGIR :
FIJAR : SET
T I TLE MENU
Dogs
Cas t l es
Love r s
B i r ds
1)Presione ▲▼ (o
) para
seleccionar el ajuste
deseado.
2)Presione (o ) para
ajustar. (DVD solamente)
• DVD Karaoke (1 vocal)
VOCAL ON➛
➛ VOCAL OFF
• DVD Karaoke (2 vocales)
➛ VOCAL➛
➛ V1VOCAL V2➛
➛ VOCAL OFF
VOCAL V1+V2➛
➛ L➛
➛R
• Video CD LR➛
Ampliación de la imagen [DVD solamente]
Durante la reproducción de un DVD, puede ampliar a
imagen seleccionando la relación de zoom usando el
botón ZOOM mediante control remoto.
Utilización de un menu de DVD
[DVD solamente]
Algunos discos DVD tienen estructuras
únicas de menús llamadas menús DVD.
Por ejemplo, los DVDs programados con un
contenido complejo proporcionan menús
guía, y los grabados con varios idiomas
proporcionan menús para audio e idiomas
de subtítulos. Aunque los contenidos de los
menús DVD y la operación cambian de
disco a disco, a continuación se explica la
operación básica cuando se utiliza esta
característica.
1
Seleccione el tamaño de la imagen.
Presione ZOOM repetidamente para cambiar el tamaño
de la imagen como se indica a continuación:
2
Presione MENU durante la
reproducción.
El menú de DVD introducido en el
disco se visualiza ahora.
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
■ Use los botones , , y para desplazar la posición hacia
arriba, hacia abajo, hacia la izquierda o hacia la derecha.
68
Dogs
1)Presione ▲▼
o las teclas
numéricas para seleccionar el
título deseado.
2)Presione SET o PLAY.
Presione AUDIO durante la reproducción para
visualizar la pantalla AUDIO.
SONIDO: 2 ENG VOZ ACTIVO
Ahora se visualiza una lista de los
títulos del disco.
of the world
Selección de vocal para los discos de
Karaoke [DVD/Video CD]
1
2
Presione TITLE durante la
reproducción.
1) Presione ▲▼
o las teclas
numéricas para
seleccionar el
articulo
deseado.
2)Presione SET
o PLAY.
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
DM2092 (P65-71 Spanish).p65
68
2002/06/19, 14:52
Reproducción programada [Vídeo CD/CD]
Puede usted programar pistas específicas y el orden de reproducción.
1
2
Presione ACTION en el modo paro (STOP)
para visualizar MAIN MENU.
MENU PRINCIPAL
DVD
BLOQUEO IDIOMA
53
TV
RELOJ
1
1)Presione ▲▼
para
seleccionar “DVD.”
2)Presione SET para visualizar.
CANAL
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
3
DVD MENU PRINCIPAL
IDIOMAS DEL DISCO
SALIDA DE AUDIO
DETENER RASTREO : CAMPO
4 : 3 PREFERENCIA : L e t t e r b o x
MODO DE REPRODUCCION
ELEGIR
FIJAR
TERMINAR
4
5
:
: SET
: ACTION
MODO DE REPRODUCCION
REPRODUCCION DE PROGRAMAS
REPRODUCCION ALEATORIA
ELEGIR
FIJAR
TERMINAR
1)Presione ▲▼ para seleccionar
“MODO DE REPRODUCCION.”
2)Presione SET para visualizar.
:
: SET
: ACTION
REPRODUCCION DE PROGRAMAS
DISCO
PROGRAMA
1 6 11 16
5 8
2 7 12 17
15 6
3 8 13 18
1 13
4 9 14 19
3 2
5 10 15 20
2
BORRAR EL ULTIMO
BORRAR TODO
ELEGIR
:
FIJAR
: SET
TERMINAR : ACTION
INICIAR
1)Presione ▲▼ para seleccionar
“REPRODUCCION DE
PROGRAMAS.” .
2)Presione SET para visualizar.
1)Presione ▲▼
para seleccionar
el número de la pista deseada. (Se
visualizan los números de la pista
del disco).
2)Presione SET para seleccionar.
• Repita el paso 5 para seleccionar otra pista.
• La pista seleccionada se añade a la parte
derecha.
6
REPRODUCCION DE PROGRAMAS
DISCO
PROGRAMA
1 6 11 16
5 8
2 7 12 17
15 6
3 8 13 18
1 13
4 9 14 19
3 2
5 10 15 20
2
BORRAR EL ULTIMO
BORRAR TODO
ELEGIR
:
FIJAR
: SET
TERMINAR : ACTION
INICIAR
1)Presione ▲▼
“INICIAR.”
2)Presione SET.
para seleccionar
• La reproducción comienza en la
secuencia programada.
• Para cancelar, presione STOP durante la
reproducción y luego presione CLEAR.
Reproducción arbitraria [Vídeo CD/CD]
For Your Information
Las pistas se reproducen de forma arbitraria.
1
2
Repita los pasos 1-3 de la “Reproduccion programa”.
MODO DE REPRODUCCION
REPRODUCCION DE PROGRAMAS
REPRODUCCION ALEATORIA
ELEGIR
FIJAR
TERMINAR
:
: SET
: ACTION
DM2092 (P65-71 Spanish).p65
1)Presione ▲▼ para seleccionar
“REPRODUCCION ALEATORIA.”
2)Presione SET.
• Comienza la reproducción arbitraria.
• Para cancelar, presione STOP durante la
reproducción y luego presione CLEAR.
69
69
2002/06/19, 14:52
Spanish Quick Use Guide/Guía para rápida consulta
Funcionamiento del DVD
utilizando visualizaciones
en pantalla
Cuando se presiona DISPLAY, la
visualización en pantalla muestra la
información del disco (título / capítulo /
número de lista, tiempo transcurrido
de reproducción, audio / idioma del
subtítulo, y ángulo) e información
(repetir la reproducción, modo
reproducción, Karaoke vocal
encendido / apagado, etc.).
1
Fijaciones iniciales
1
2
3
• Cada vez que se presione DISPLAY,
la visualización en pantalla cambia
como se muestra a continuación.
Información seleccionada del disco
➛
Selected
unit information
Información
seleccionada
de la unidad
➛
Pantalla
normal Screen
Normal
1)Presione ▲▼ (o
) para
seleccionar el articulo deseado.
2)Presione SET para colocar.
3
1)Presione ▲▼
para seleccionar “DVD.”
2)Presione SET para visualizar.
1) Presione ▲▼ para seleccionar el artículo deseado.
2)Presione SET.
IDIOMAS DEL DISCO
Todos los idiomas ofrecidos en el disco pueden ser
ajustados, Si el idioma ajustado no es ofrecido en el
disco, se seleccionará el idioma original del disco.
SALIDA DE AUDIO
Puede usted ajustar la salida audio procedente de la
terminal de salida audio digital.
DETENER RASTREO
Para seleccionar “CAMPO” o “CUADRO” para prevenir
inestabilidad o para permitir ver textos pequeños o
patrones finos claramente en el modo de imagen fija.
4 : 3 PREFERENCIA
Para seleccionar si el material del vídeo para pantalla
ancha será vuelto a reproducir en el estilo Pan&Scan o
en el estilo Letterbox en la pantalla.
Presione DISPLAY en el modo
reproducción o parada para
visualizar en pantalla.
2
Presione ACTION en el modo de paro (STOP)
para visualizar MAIN MENU.
4
5
1) Presione ▲▼ para seleccionar el artículo deseado.
2)Presione SET.
Volver a visualizar el menú de DVD para
continuar el ajuste.
Presione ACTION y pase al paso 3 para ajustar otro
articulo o, para salir, presione ACTION tres veces.
<Ejemplo de DVD>
T I TULO : 12
CAPITULO: 11
T I TULO : 12
CAPITULO: 24
DVD
0 : 12 : 34
DVD
0 : 12 : 34
ELEGIR :
FIJAR : SET SIGUIENTE: DISPLAY
ELEGIR :
FIJAR : SET SIGUIENTE: DISPLAY
1)Presione
▲▼ para
seleccionar
el ajuste
deseado.
2)Presione
SET para
colocar.
<Ejemplo de Vídeo CD>
PISTA
PBC
: 12
: INACTIVO
PISTA
PBC
FIJAR
: 17
: INACTIVO
VIDEO CD
0 : 12 : 34
VIDEO CD
0 : 12 : 34
: SET SIGUIENTE: DISPLAY
FIJAR
Para volver
a la pantalla
normal,
presione
repetidamente
CLEAR o
DISPLAY.
: SET SIGUIENTE: DISPLAY
Selección de IDIOMAS DEL DISCO
[DVD solamente]
Seleccione “AUDIO”
Inglés/Español/Francés/Japones: (Fijación de fábrica : inglés)
Original : Se seleccionará el idioma original de cada
disco.
OTRO **** : Se puede seleccionar el otro idioma.
Seleccione “SUBTITULO”
AUTO : Se seleccionará el mismo que fue seleccionado en
la preparación de “AUDIO”. (Fijación de fábrica)
• Si el idioma seleccionado en la preparación de
“AUDIO” se utiliza durante la reproducción, los
subtítulos no aparecerán.
• Si se utiliza otro idioma durante la reproducción,
los subtítulos aparecerán en el idioma
seleccionado en la preparación de “AUDIO”
Inglés/Español/Francés/Japones
OTRO **** : Se puede seleccionar el otro idioma.
Seleccione “MENU”
Inglés/Español/Francés/Japones : (Fijación de fábrica : inglés)
OTRO **** : Se puede seleccionar el otro idioma.
70
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
DM2092 (P65-71 Spanish).p65
70
2002/06/19, 14:52
Selección de SALIDA DE AUDIO
Seleccione “LPCM(DVD)”
INACTIVO : Por el conector de salida de audio digital
solamente sale PCM lineal de 48 kHz/16
bits. Durante la reproducción del DVD
grabado en el PCM lineal de 48 kHz/20
bits o 96 kHz, no sale audio digital.
(Fijación de fábrica)
PCM :
Durante la reproducción del DVD
grabado en el PCM lineal de 48 kHz/20
bits/24 bits o 96 kHz, sale audio digital
convertido a 48 kHz/16 bits. (La salida
digital de audio PCM está restringida a
48 kHz/16bits o menos para proteger
los derechos de autor.)
Selección de DETENER RASTREO
AUTO :
Durante el modo de imagen fija se
seleccionarán automáticamente
“Campo fijo” o “Cuadro fijo” (Fijacion
de fabrica)
CAMPO : Seleccione este ajuste cuando
ocurra “distorsión” en las imagenes,
incluso cuando se haya
seleccionado “AUTO”.
CUADRO : “Cuadro fijo” esta siempre
seleccionado. Se utiliza cuando no
se puedan ver claramente textos
pequeño o patrones finos incluso
cuando esté seleccionado “AUTO”.
Seleccione “Dolby Digital”
Bitstream: Sale un flujo de bits Dolby digital
(2ch-5.1ch). (Fijación de fábrica)
INACTIVO : No hay salida de audio.
Seleccione “dts”
Bitstream : Sale un flujo de bits dts. (Fijación de
fábrica)
INACTIVO : No hay salida de audio.
Seleccione “DRC (Dynamic Range Compression)”
INACTIVO : Se selecciona el margen de audio
normal. (Fijación de fábrica)
ACTIVO :
Seleccione este ajuste para disfrutar de
un sonido dinámico incluso a bajo
volumen. Esto es muy útil para escuchar
durante la noche. [Esta función sólo se
activa con DVDs Dolby Digital.]
Seleccione “SURROUND”
El sonido envolvente crea el efecto de sonido que
procede de altavoces que parecen estar en la
parte de atrás aún cuando solo se ha conectado a
un sistema estéreo de 2 canales.
INACTIVO : No efecto de sonido envolvente.
(Fijación de fábrica)
ACTIVO :
Efecto de sonido envolvente.
Selección de 4 : 3 PREFERENCIA
Pan&Scan : Datos de la pantalla ancha de vídeo
son reproducidos en el estilo Pan &
Scan (la parte derecha e izquierda
de la pantalla son recortadas).
(Fijación de fábrica)
• Datos de vídeo no formateados en
Pan & Scan serán reproducidos en
el estilo letterbox.
Letterbox : Datos de la pantalla ancha de vídeo
son reproducidos en el estilo
Letterbox (la parte de arriba y abajo
de la pantalla tienen un margen
negro).
For Your Information
71
DM2092 (P65-71 Spanish).p65
71
2002/06/19, 14:52
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it
with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
Parts
Product
Labor
Ninety (90) Days
Camcorder
One (1) Year (except
CCD Image Sensor)
CCD Image Sensor
- 6 (Six) Months
DVD/VCR Deck,
A/V Mixer
One (1) Year
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
One (1) Year
(except CRT)
CRT - Two (2) Years
TV/HDR
Combination
One (1) Year
(except CRT)
CRT - Two (2) Years
Ninety (90) Days
Ten (10) Days
Rechargeable
Batteries
(in exchange for
defective item)
Tape
(in exchange for
defective item)
Memory Cards
(in exchange for
defective item)
Service
Contact Number
Carry-In or Mail-In
1-800-211-PANA(7262)
Ninety (90) Days
Carry-In or Mail-In
1-800-211-PANA(7262)
Ninety (90) Days
Carry-In: 21” CRT
and Smaller
In-Home or Carry-In:
22” CRT and Larger
1-800-211-PANA(7262)
In-Home or Carry-In
1-888-843-9788
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Five (5) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Ninety (90) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there
will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service, as
applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products
purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original
purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original
purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number
listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized
servicer and does not include removal or re-installation of an installed product. It is possible that certain
in-home repairs will not be completed in-home, but will require that the product, or parts of the product, be
removed for shop diagnosis and/or repair and then returned.
72
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P72-73 Warranty).p65
72
2002/06/19, 14:52
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on the
picture tube resulting from viewing fixed images (including, among other things, letterbox pictures on
standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or onscreen data
in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which occurred in
shipment, or failures which are caused by products not supplied by the warrantor, or failures which result
from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up
adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning
damage, modification, or commercial use (such as in a hotel, office, restaurant, or other business), rental
use of the product, service by anyone other than a Factory Servicenter or other Authorized Servicer, or
damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone
remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or images,
data or other memory or recorded content. The items listed are not exclusive, but are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY,
ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state. If a problem with this product develops during or after the warranty period, you may contact your
dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s
Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE APPLICABLE)
WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY.
Customer Services Directory
For Product Information, Operating Assistance, Literature Request, Dealer Locations,
and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.
or send e-mail : [email protected]
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
As of February 2002
DM2092 (P72-73 Warranty).p65
73
73
2002/06/19, 14:52
For Your Information
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Index
TV / VCR
A Accessories ............................................... 4
B
C
D
E
F
AC Power Plug ......................................... 11
ACTION button .................................... 8, 16
ADD / DLT / CLEAR button ................. 8, 17
Audio Adjustment ..................................... 47
Audio Auto Gain Control (AGC) ............... 46
AUDIO button ....................................... 8, 23
Audio Connections ................................... 12
Audio Features ................................... 46, 47
Audio Menu ............................................... 46
Audio Mode for FM Radio ........................ 29
Audio Mode for Playback ......................... 44
Audio Mode for Recording ....................... 44
Audio Mode for TV Viewing ...................... 23
Audio Mute ................................................ 22
Audio / Video Input
connector (LINE) ............................... 10, 19
Audio Output Connector (L/R) ........... 11, 12
Auto Operation Functions ........................ 37
Batteries ..................................................... 4
Before Requesting Service ................ 62, 63
Before Using ............................................... 4
Blocking Message .................................... 43
Blue Screen Display ................................. 27
Broadcast Types ..................................... 23
Cable Box Brand Code Number .............. 33
Cable Box Universal Remote
Control Feature ........................................ 32
Cassette Compartment ........................... 10
Caption On Mute ...................................... 25
Channel .................................. 14, 16, 17, 27
Channel Caption ....................................... 38
CHANNEL UP / DOWN button ................ 22
Clock ........................................................ 16
Closed Caption ................................... 24, 25
CM SKIP / ZERO SEARCH button 8, 36, 37
Code Numbers, DSS / Cable Box Brand .. 33
Commercial Skip ...................................... 37
Connections ............................................. 11
Connections, Audio .................................. 12
Connections, DSS / Cable Box ................ 11
Connections, Outdoor Antenna ............... 11
Copy Your Tapes (Dubbing) ................... 19
COUNTER RESET button ................... 8, 36
Customer Services Directory ................. 73
DISPLAY / ENTER button .............. 8, 27, 32
DSS Brand Code Number ....................... 33
DSS CABLE button .............................. 8, 32
DST (Daylight Saving Time) ...................... 6
EJECT button ......................................... 8, 9
Eject tape .................................................. 18
Fast Forward ............................................ 18
FF/SLOW+ button ................................ 8, 18
FM button ....................................... 8, 28, 29
FM Radio ............................................ 28, 29
Forward Search ....................................... 18
Frame by Frame Advance ...................... 18
Front Panel Indicators ................................ 9
Function Display ...................................... 27
74
H Head Cleaning ............................................ 6
I Important Safeguards and Precautions .... 2
L
M
N
O
P
Q
R
S
Information (Unit, Cassette, Disc) ........ 6 - 7
Initial Setup ............................................... 14
Index Search ............................................ 34
Indicators on the Front Panel .................... 9
Input Mode ................................................ 19
Language ............................................ 14, 16
LIGHT button .......................................... 8, 9
Location of Controls ............................ 8 - 11
MTS Broadcast / TV Stereo System ....... 23
MUTE button ........................................ 8, 22
NUMBER keys ..................................... 8, 22
100 Key .................................................... 22
One Touch Recording (OTR) ................. 18
On-Screen Display (OSD) ...................... 27
ON-TIMER with Alarm ............................. 26
Phones ..................................................... 22
Playback ................................................... 18
PLAY button .......................................... 8, 18
POWER button ..................................... 8, 14
PROG button .................................. 8, 26, 30
Program End Search ............................... 35
PROG TIMER Indicator ................. 9, 26, 30
Quality Picture ............................................ 6
Rapid Tune ............................................... 22
R-TUNE button ........................................ 22
REC button ........................................... 8, 18
REC Indicator ....................................... 9, 18
Rec(ord) ................................................... 18
Record / Playback Speed Settings ........... 4
Remote Control Buttons ............................ 8
Remote Sensor .......................................... 9
Remote Warning Feature ........................ 39
Repeat Play .............................................. 36
Reset Language, Channels, Clock ... 16, 17
Reset unit ................................................. 15
Reverse Search ....................................... 18
REW/SLOW- button ............................. 8, 18
Rewind ...................................................... 18
Safety Precautions ..................................... 3
SEARCH button ............................. 8, 34, 35
Secret Code ............................................. 40
Selecting Input Mode ................................ 19
SELECT / SET button .......................... 8, 16
Sleep Timer .............................................. 26
Slow Motion .............................................. 18
Spanish Quick Use Guide ............... 65 - 71
Special VCR Features ....................... 38, 39
Specifications ............................................. 6
SPEED button ...................................... 8, 18
Still Picture ................................................ 18
STILL / PAUSE button .......................... 8, 18
STOP button ......................................... 8, 18
SURROUND button ............................. 8, 45
Surround Sound ....................................... 45
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
DM2092 (P74-75 Index).p65
74
2002/06/19, 14:52
TV / VCR
T Table of Contents ....................................... 5
Tape Erasure Prevention .......................... 4
Tape Operation ................................. 34 - 37
Timer Program Review, Replace, Clear ... 31
Timer Recording ...................................... 30
Timer Recording Cancellation ................. 31
Time Zone Adjust ..................................... 17
TRACKING / V-LOCK buttons .............. 6, 8
TV Operation ............................................ 22
TV Timer Features ................................... 26
TV - VCR button ................................... 8, 32
TV/VCR Status & Clock Display .............. 27
U Unit, Front/Rear View .......................... 9 - 11
Universal Remote Control ....................... 32
US MOVIES Ratings ................................ 41
US TV PROGRAMS Ratings ................... 42
V VCR Lock ................................................. 39
Video Adjustment ..................................... 47
Video Menu ............................................... 46
V-Chip Control Feature ..................... 40 - 43
VHF / UHF Antenna Input Terminal ........ 11
VOLUME UP / DOWN button .............. 8, 22
DVD
A ANGLE button ...................................... 8, 49
B
C
D
K
Warning and Instruction Displays ........... 64
Weak Signal Display Feature .................. 39
Z Zero Search ............................................. 36
L Language Code List ................................. 61
M MENU button ........................................ 8, 50
O
P
R
S
T
U
Z
MP3 Playback Operation ......................... 56
Multiple angle viewing (DVD) ................... 49
OPEN / CLOSE button ........................ 8, 20
Optical digital audio output connector .. 11, 13
Picture Zoom (DVD) ................................ 49
Play ........................................................... 20
Playback control (Video CDs) ................. 21
PLAY button ......................................... 8, 20
Program Play (Video CD/CD) ................. 51
Program Repeat Play (Video CD/CD) ..... 51
Random Play (Video CD/CD) .................. 52
Region number ........................................... 3
Repeat Play .............................................. 55
RESUME function .................................... 21
RETURN button ................................... 8, 20
REW button .......................................... 8, 20
Settings for DVD Operation ..................... 58
SKIP + / - button ............................. 8, 20, 21
Slow Motion (DVD/Video CD) .................. 21
SLOW + / - button ................................ 8, 21
STILL MODE ............................................ 60
Still (Pause) Picture ................................. 21
STILL / PAUSE button ......................... 8, 21
Subtitle language (DVD) .......................... 48
TV MODE ................................................. 60
Title menu (DVD) ..................................... 50
Unit information screen (Unit) ................. 55
ZOOM button ....................................... 8, 49
75
DM2092 (P74-75 Index).p65
75
2002/06/19, 14:52
For Your Information
F
ANGLE Indicator .................................. 9, 49
Auto-Power Off function .......................... 21
AUDIO button ....................................... 8, 48
AUDIO OUTPUT ..................................... 59
Audio soundtrack language (DVD) ......... 48
Basic DVD Operation ............................... 20
CLEAR button .......................... 8, 51, 52, 53
Definition of terms ...................................... 7
Disc Audio attribute 1 type, sampling
frequency, bit No. ..................................... 48
Disc format ................................................. 7
Disc handling .............................................. 7
Disc information screen ........................... 54
DISC LANGUAGES (DVD) ..................... 58
Disc Operation .................................. 48 - 52
Disc Tray ........................................ 7, 10, 20
DISPLAY button ................................... 8, 53
DVD button ........................................... 8, 20
DVD Lock Feature (DVD) ....................... 57
DVD Lock Ratings (DVD) ........................ 57
DVD menu (DVD) .................................... 50
DVD Operation using On-Screen Displays .. 53
DVD Volume Adjust .................................. 45
FF button .............................................. 8, 20
Forward / Reverse Chapter / Track skip .. 21
Forward / Reverse rapid scene search ... 21
Frame by Frame picture
(DVD/Video CD) ....................................... 21
Karaoke (DVD/Video CD) ........................ 49
W Warranty ............................................. 72, 73
LSQT0608A
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
DM2092 (P76 BC).p65
76
P
Printed in U.S.A
LSQT0608A
M0602-0
2002/06/19, 14:52
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement