Panasonic PVC921 Operating Instructions

Panasonic PVC921 Operating Instructions
Initial Setup
Combination VCR
Operating Instructions
Basic Operation
Models No. PV-C911 / PV-C921 / PV-C931W
TV Operation
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
LSQT0603A
As an ENERGY STAR® Partner,
Matsushita Electric Corporation
of America has determined that
this product or product model
meets the ENERGY STAR®
guidelines for energy efficiency.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 8 to 13.
• SELF-DEMO Procedure is on page 4.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the
AC power cord. Regularly remove dust, dirt, etc.
on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not
tamper with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances
and walking traffic. Do not rest heavy objects on,
or roll such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type
plug (polarized or grounding) and must be
securely connected.
- Overloaded wall outlets or extension cords is a
fire hazard.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa,
rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator,
in direct sunlight, etc. If unit is suddenly moved
from a cold place to a warm place, moisture may
condense in unit and on the tape causing
damage.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or stand that is not
firm, level, and adequately strong.
The unit could fall causing serious
injury to a child or adult and
damage to the unit.
• Move any appliance and cart
combination with care.
Quick stops, excessive force, and
uneven surfaces may cause objects to overturn.
• Carefully follow all operating instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly
grounded to provide some protection
against built up static charges
and voltage. Section 810
of the National Electrical
Code, ANSI/NFPA 70 (in
Canada, part 1 of the
Canadian Electrical Code)
provides information
regarding proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE
POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power
lines and electric light or power circuits so it will never
touch these power sources should it ever fall. When
installing antenna, absolutely never touch power lines,
circuits or other power sources as this could be fatal.
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR
MOISTURE, such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug unit and have it inspected
by a qualified service technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from
the power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a
service technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
• Keep magnetic objects, such as speakers, away from
unit to avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer
to avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit and
cause electrical shock. Any substance, such as wax, adhesive
tape, etc. may mar the cabinet surface. Exposure to greasy,
humid, or dusty areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or
remove covers, or make any adjustments not described in the
manual. Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified
by the manufacturer, or have equal safety characteristics
as original parts. The use of unauthorized substitutes may
result in fire, electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a through safety
check be done as described in the manufacturer’s service
literature to ensure video unit is in safe operating condition.
Safety Precautions /
Mesures de sécurité
To prevent fire or shock hazard, do not
expose this equipment to rain or moisture.
Caution:
To prevent electric shock, match wide
blade of plug to wide slot, fully insert.
Avertissement:
Attention:
Record On a Tape ................................ 14
Copy Your Tapes (Dubbing) ............... 15
TV Operation ........................................ 16
Picture Adjustment .............................. 17
TV Timer Features ................................ 18
Closed Caption System ....................... 20
FM Radio ............................................... 22
<Model PV-C921/PV-C931W only >
FM Transmitter ..................................... 23
<Model PV-C921/PV-C931W only >
Any unauthorized changes or
modifications to this equipment would
void the user’s authority to operate.
Timer Recording ................................... 24
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol warns the user that
uninsulated voltage within the
unit may have sufficient
magnitude to cause electric
shock. Therefore, it is dangerous
to make any kind of contact with
any inside part of this unit.
This symbol alerts the user that
important literature concerning
the operation and maintenance
of this unit has been included.
Therefore, it should be read
carefully in order to avoid any
problems.
Tape Operation ..................................... 26
Special VCR Features ......................... 30
V-Chip Control Feature ....................... 34
On-Screen Display (OSD) ................... 38
Warning and Instruction Displays ..... 39
Operation Differences Using AC or DC Power .. 40
Unit Information ................................... 41
Before Requesting Service ................. 42
Service Center List .............................. 43
Limited Warranty ................................. 44
Spanish Quick Use Guide /Guía para rápida consulta ... 45
Index ...................................................... 48
3
Timer Operation Advanced Operation For Your Information
FCC WARNING:
TV Operation
Pour éviter les chocs électriques,
introduire la lame la plus large de la fiche
dans la borne correspondante de la prise
et pousser jusqu’au fond.
This video recorder, equipped with the HQ
(High Quality) System, is compatible with
existing VHS equipment. Only use those
tapes with the
mark. It is recommended
that only cassette tapes that have been
tested and inspected for use in 2, 4, 6, and 8
hour VCR machines be used. This television
receiver provides display of television closed
captioning in accordance with §15.119 of the
FCC rules.
Reset Language, Channels,
Clock, Time Zone Adjust .................... 12
Playback a Tape ................................... 14
Basic Operation
Afin de prévenir tout risque d’incendie ou
de chocs électriques, ne pas exposer cet
appareil à la pluie ou à une humidité
excessive.
Important Safeguards and
Precautions / Safety Precautions ........ 2,3
Table of Contents .................................. 3
Before Using .......................................... 4
Connections ........................................... 5
Location of Controls ............................. 6
Initial Setup for ANT. / Cable Connection ........ 8
Initial Setup for DSS / Cable box Connection .. 10
Initial Setup
Warning:
Table of Contents
Before Using
Congratulations
on your purchase of one of the most sophisticated and
reliable products on the market today. Used properly, it
will bring you and your family years of enjoyment.
Please fill in the information below. The serial number is
on the tag located on the back of your unit.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Accessories
SELF-DEMO Mode
With Power ON, press
PLAY/REPEAT on the
unit for 7 seconds to
deactivate the
SELF-DEMO Mode.
Repeat this to display
demo screen.
Loading the Batteries
1) Open the cover.
2) Insert batteries
as marked.
Remote Control
LSSQ0281
(PV-C921)
LSSQ0282
(PV-C931W)
Remote Control
LSSQ0280
(PV-C911)
3) Close the cover.
Battery replacement caution
Batteries
2 “AA”
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Prevent Accidental Tape Erasure
Break off the tab to protect.
300 ohm-75 ohm
Transformer
VSQS0974
Indoor Antenna
TSA700009
Record Tab
Screw driver
To record again.
AC Power Cord
VJAW0044
(PV-C911, PV-C921)
DC Car Cord (2m)
LFX6301A
LFX6109A
(PV-C931W)
To order accessories, call toll free 1-800-332-5368.
4
Cover the hole
with cellophane tape.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections
Insert the Indoor antenna (supplied) into
the receptacle on the back of the unit.
Then, connect the two wires to the 300
ohm-75 ohm transformer (supplied.)
Next, connect the transformer to the
back of the unit as shown.
Now, extend the antenna and adjust its
length, direction and angle for the
clearest picture.
Indoor Antenna (supplied)
300-75 ohm
Transformer
(supplied)
Connecting to a Power Source
Your unit goes where you go with two different ways to supply power. You may connect
the supplied AC (alternate current) cord for use with any AC outlet. Or when travelling,
connect the supplied DC (direct current ) Car Battery cord which can be inserted in your
vehicle’s cigarette lighter. For your safety and to avoid damage to the unit, please follow
instructions and connections carefully.
■ Connecting the (supplied) AC Cord
1. Connect the supplied AC cord to the AC input jack
on the back of the unit as shown.
2. Plug the AC cord into an AC wall outlet.
Close the cover.
■ Connecting the (supplied) DC Cord
1. Connect the DC Car Battery cord to the DC input
on the back of the unit as shown.
2. Start the engine of your vehicle.
• DO NOT insert the cord into the cigarette lighter
until the engine is running.
3. Remove the cigarette lighter from it’s socket and
insert the Car Battery plug in it’s place.
IMPORTANT NOTES
• This cord can only be used in vehicles equipped with DC
12V or 24V (negative ground) batteries. Check your car’s
owner’s manual.
• Use the only the Car Battery cord packed with your unit.
• To avoid a loss voltage, do not attach an extension to
the Car Battery cord.
• When unit is not in use, disconnect the Car Battery cord
from the cigarette lighter socket to save car battery.
■ Replacing the DC Car Cord Fuse
If the safety fuse in the car cord plug blows out,
replace it as follows.
1. Unscrew the cap (counterclockwise.)
2. Replace using a 125V 10A fuse.
• Only use fuses with the exact voltage and amps specified.
3. Replace the cap (clockwise.)
Fuse Cap
5
Initial Setup
Indoor Antenna Connections
Location of Controls
Remote Control Buttons
EJECT button:
When EJECT is pressed, the tape is ejected from Cassette Compartment.
If EJECT is pressed during recording, the unit will not respond to the command.
<Model PV-C921/PV-C931W remote shown>
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
Front View of the unit and Indicators on the Front Panel
<Model PV-C921/PV-C931W unit shown>
REWIND/SEARCH Page 14.
Page 13.
ACTION
STOP/EJECT
ACTION
Cassette Compartment
Page 14.
Page 14.
Page 13.
PLAY/REPEAT
Page 14.
CHANNEL UP/DOWN Page 16.
TRACKING UP/DOWN Page 41.
SELECT UP/DOWN Page 13.
FAST FORWARD/SEARCH
Page 14.
Built-In Front
Side Speaker
VOLUME UP/DOWN Page 16.
SET/BACK SPACE Page 13.
REC
Page 14.
POWER
Page 8.
TIMER Page 19.
FM Page 22.
Audio/Video In Jack
Page 15.
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
POWER
REC
REC
ON TIMER
PROG TIMER
AUDIO IN
Phones Jack
Page 16.
ACTION
POWER Indicator
Light when the unit is turned on.
Remote Control is functional
only when this indicator is lit.
POWER
Remote Sensor
REC Indicator
Lights during recording.
In Rec Pause or OTR Pause
mode, the indicator flashes.
Page 14.
REC
ON TIMER
PROG TIMER
PROG TIMER Indicator
Lights when the unit is set
for Timer Recording.
It flashes when a Timer
Recording has been set
with no tape inserted,
the clock is not set, or the
tape is in motion.
Page 24.
ON TIMER Indicator
Lights when the On Timer is set.
Page 18.
Rear View of the unit
Easy-Grip-Handle
Use when
transporting the unit.
DC Input jack
For connection to the
DC Car Battery Cord.
AC Input jack
For connection to the
AC Power Cord.
VHF/UHF Antenna
Input Terminal
In from your Antenna
or Cable.
Pages 5, 8, 10.
7
Initial Setup for ANT. / Cable Connection
How to Connect
■ Connect the Cable from Antenna / Cable to the VHF / UHF
terminal on unit.
WARNING:
UNIT
When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.
IN from
CABLE
VHF/UHF
VHF/UHF
How to do Initial Setup
1
Press POWER on the unit.
2
When the unit is turns on the
first time, SELECT
LANGUAGE screen appears.
3
Press CH
to select English.
OR
Press CH to select Spanish
(Español).
OR
Press VOL + to select French
(Français).
CHANNEL/CLOCK AUTO SET
screen appears.
CHANNEL / CLOCK AUTO SET
CONNECT ANTENNA CABLE
AND I F YOU USE A CABLE
BOX, TUNE I T TO YOUR
LOCAL PBS CH
THEN. . .
PLE ASE PRESS CH UP KEY
• If wrong language is set, complete “Reset
all unit Memory Functions” steps page 9.
8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
nection
Initial Setup
4
Press CH to start
CHANNEL / CLOCK AUTO SET
operation. Settings are performed
automatically. If the setup is
completed, the following screen is
displayed.
2 / 7 / 2001 WEDDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
END : PRESS CH UP KEY
If AUTO CLOCK SET IS
INCOMPLETE screen appears, set
the clock using MANUAL CLOCK
SET procedures as below.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
Manual Clock Set
If AUTO CLOCK SET was incomplete,
manually set the clock as follows.
Press ACTION on the Remote to
display SET CLOCK Menu screen.
1
SET CLOCK
:
1/ /
DST : ON
SELE CT MONTH
SELECT :
SET
:
END
: ACT I ON
2
Press
to select the month and
press to set. In the same manner,
select and set the date, year, time,
and DST. (Daylight Saving Time).
SET CLOCK
2 / 7/2001 WED 12: 00PM
DST : ON
SET COMPLETED
SET
END
3
:
: ACT I ON
Press ACTION twice to start CLOCK
and exit.
Model PV-C921/PV-C931W
remote is shown here.
Reset all unit Memory Functions
When moving unit to a new location, or if a
mistake was made in the Initial Setup
section.
• Make sure a tape is not inserted in the unit.
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
AUDIO IN
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
REC
ON TIMER
PROG TIMER
ACTION
1 Turn the unit
Power on.
2 Press and hold both PLAY and
FF on the unit for more than 5
seconds.
• The power will shut off.
3 Do “Initial Setup” on page 8.
9
Initial Setup for DSS / Cable box Connection
How to Connect
■ Connect the OUT Jack on your cable box to the VHF/UHF
terminal on unit with an RF cable.
UNIT
WARNING:
When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.
Cable TV
Converter Box
IN from
CABLE
VHF/UHF
VHF/UHF
How to do Initial Setup
1
2
Press POWER on the unit.
When the unit is turns on the
first time, SELECT
LANGUAGE screen appears.
3
Press CH
to select English.
OR
Press CH to select Spanish
(Español).
OR
Press VOL + to select French
(Français).
CHANNEL/CLOCK AUTO SET
screen appears.
CHANNEL / CLOCK AUTO SET
CONNECT ANTENNA CABLE
AND I F YOU USE A CABLE
BOX, TUNE I T TO YOUR
LOCAL PBS CH
THEN. . .
• Turn on your cable box and set it to
PBS(Public Broadcast Station) channel
in your time zone. If you use DSS
receiver, it must be turned off.
10
PLE ASE PRESS CH UP KEY
• If wrong language is set,
complete “Reset all unit Memory
Functions” steps page 9.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
4
Press CH to start
CHANNEL / CLOCK AUTO SET
operation. Settings are performed
automatically. If the setup is
completed, the following screen is
displayed.
2 / 7 / 2001 WEDDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
END : PRESS CH UP KEY
If AUTO CLOCK SET IS
INCOMPLETE screen appears, set
the clock using MANUAL CLOCK
SET procedures shown page 9.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
Model PV-C921/PV-C931W
remote is shown here.
Note to CABLE System Installer
This reminder is provided to call the CABLE (Cable TV) System Installers attention to
Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
11
Reset Language, Channels, Clock,
1
Press ACTION
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
to display MAIN MENU.
SELECT :
SET
: ACT I ON
2
Language
1) Press
to
select language
icon.
Clock
Channels
1) Press
select “CH.”
to
1) Press
to
select “CLOCK.”
M A I N MENU
M A I N MENU
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
2) Press ACTION.
2) Press ACTION
repeatedly.
MENU PR I NC I PAL
HOLA
TV
VCR
IDIOMA
CANAL
REL OJ
SAL I R
ELEG I R :
F I JAR : ACT I ON
For Spanish
MENU
SET UP CHANNEL
ANTENN
ENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
:
END
: ACT I ON
3) Press
to select
“ANTENNA,” then
press to set your
antenna system
(“TV” or “CABLE”).
BONJOUR
T ELE
LANGUE
MAGNET .
CANAL HORLOGE SORT I E
SEL.
:
REGLER : ACT I ON
For French
M A I N MENU
• After Channel Auto Set
is finished, Clock Auto
Set will be performed.
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANU
NUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
:
: ACT I ON
END
(“TIME ZONE ADJUST”
appears only when
auto clock is set.)
3)Press
to select
“MANUAL” or
“AUTO CLOCK
SET” and press .
• For Auto Clock Set,
select “AUTO CLOCK
SET,” then press CH .
SET CLOCK
2 / 7/2001 WED 12: 00PM
DST : ON
HELLO
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
For English
3) Press
to
select “EXIT.”
Press ACTION to
exit.
12
to select
4) Press
“AUTO SET,” then
press .
TV
SELE CT HOUR
SE
SELECT :
SET
:
END
: ACT I ON
4)Press
and
to
press
select and set the
month, date, year,
time, and DST
(Daylight Saving
Time).
5) Press ACTION
twice to start the
clock and exit this
mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Time
Clock,
Time Zone Adjust
Time Zone Adjust
(Only when Auto Clock is set.)
Basic Operation
1) Press
to
select “CLOCK.”
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
Model PV-C921/PV-C931W
remote is shown here.
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
ACTION key on
the unit
Using
SELECT :
SET
:
: ACT I ON
END
3) Press
to select
TIME ZONE
ADJUST and
press or to
subtract or add
hour(s) as
necessary.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
SET
:
: ACT I ON
END
4) Press ACTION
twice to exit.
• TIME ZONE
ADJUST returns to
“0” if clock is set
manually.
keys
VOL
On Unit
You can operate the
menu screen using
unit buttons.
To display the menu,
press STOP/EJECT
and REW together
with no tape inserted.
To exit the menu,
repeat above with or
without tape inserted
until normal screen
appears.
On Remote
CH
On Unit
: CH UP
: CH DOWN
: VOLUME UP
: VOLUME DOWN
Whenever the menu or program
screen is displayed,CHANNEL
UP/DOWN function as
and
VOLUME UP/DOWN function as
only.
Add or Delete a Channel
To add channel:
To delete channel:
Select channel with
number keys and
press ADD/DLT.
Select channel with CH
or number keys and
press ADD/DLT.
CHANNEL 08 ADDED
CHANNEL 08 DELE TED
13
Playback a Tape
Ready Check List
All connections are made.
Your unit is plugged in.
1
Insert a cassette.
• The unit power comes
on automatically.
Record
tab
To prevent tape jam,
remove loose or peeling labels
from tapes.
2
■
■
■
■
1
2
3
Insert a cassette with record tab.
• The unit power comes on automatically.
Press CH
or number keys to
Select Channel.
• For “LINE” input, see bottom of next page.
Press SPEED to select recording
speed (see page 41).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Selected speed is displayed.
Press PLAY.
• Playback begins if cassette has no
record tab.
Forward/Reverse scene search
➔ Press FF or REW
➔ Press again or PLAY to release.
Still (Freeze) picture
➔ Press PAUSE/SLOW
➔ Press PLAY to release.
Slow Motion picture
➔ Hold down PAUSE/SLOW in
Still mode
➔ Press PLAY to release.
Frame by Frame picture
➔ Press PAUSE/SLOW in Still mode
➔ Press PLAY to release.
Notes
• These features work best in SLP mode.
• After the unit is in Still or Slow mode for 3
minutes, it will switch to Stop mode automatically
to protect the tape and the video head.
■
■
■
■
Record On a Tape
Stop ➔ Press STOP
Rewind tape ➔ Press REW in Stop mode
Fast forward tape ➔ Press FF in Stop mode
Eject tape ➔ Press EJECT on the remote
or STOP/EJECT on the unit
4
Start Recording.
Press REC.
• To edit out unwanted portions, press
PAUSE/SLOW to pause and resume
recording.
• You cannot view another channel during
recording.
■ Stop ➔ Press STOP
• When using DC Power supply, pressing
POWER on the remote will cancel
Recording in progress.
■ One Touch Recording (OTR)
Press REC repeatedly
0:30
Normal Rec
1:00
to set the recording
1:30
2:00
3:00
4:00
length (30 min - 4 hours.)
• The unit stops recording at a preset time.
• PROG TIMER indicator lights on the unit.
Notes
• After the unit has been in Rec Pause mode for 5
minutes, it will stop automatically to protect the
tape and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
• When using DC Power supply, pressing POWER
on the unit will cancel an OTR in progress.
You can operate on the unit
CH
PLAY
REC
Insert a cassette.
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
PLAY/
REPEAT
AUDIO IN
FF/
REC
TIMER/
FM
POWER
REC
ON TIMER
PROG TIMER
ACTION
■ Press to stop and/or
eject tape.
14
REC Indicator
Model PV-C921/
PV-C931W remote is
shown here.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Copy Your Tapes (Dubbing)
Connections you’ll need to make.
Recording (Editing) unit
Playing (Source) VCR
AUDIO VIDEO
OUT
OUT TO TV
Playback (Source)
1
Recording (Editing) unit
Insert blank tape
with record tab.
Insert prerecorded tape.
Our Vacation
2
3
VIDEO IN AUDIO IN
AUDIO IN
• Dubbing tapes protected
with Copy Guard will have
poor quality results.
Select “LINE” mode.
See “Selecting Input Mode” below.
Press PLAY then
PAUSE at starting
point to put in
Press REC, then
PAUSE/SLOW
immediately to put in
Standby mode.
Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
5
STOP
Press PLAY
Press PAUSE/SLOW
to start dubbing.
to start dubbing.
Press STOP
Press STOP
to stop dubbing.
to stop dubbing.
Selecting Input Mode
Method 1:
Press CH
. The display will change as follows.
1
Caution
• Unauthorized exchanging
and/or copying of copyrighted
recordings may be copyright
infringement.
2
3
(CABLE) (TV)
125 or 69
LINE
Method 2:
a Press ACTION for MAIN MENU.
b Press
to select “TV”, then press ACTION
for SET UP TV screen.
c Press
to select “INPUT SELECT,” and
then press to select “TUNER” or “LINE.”
d Press ACTION twice to exit this mode.
15
Basic Operation
IN
IN FROM ANT.
TV Operation
1
2
Press POWER on the remote or
unit.
08
ABC
3
Ready Check List
All connections are made.
Your unit is plugged in.
Use CH
or
number keys to
select a channel.
Press VOL + or VOL to adjust volume.
VOL + / VOL PLAY/REPEAT
24
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
AUDIO IN
REC
ON TIMER
PROG TIMER
ACTION
NIGHT (NITE) Mode
Color and picture intensity levels are adjusted so the
screen is easier on your eyes during night time use.
N I GHT
CH
PHONES
Jack
POWER
Press NITE to set NIGHT
mode.
• NIGHT mode may be selected
when watching TV, playing a
tape, or while in FM mode.
Press NITE to cancel.
• Previous settings are restored.
• NIGHT mode is canceled
when power is turned off or
power failure occurs.
■ Using the 100 key
When selecting CABLE channels
100 to 125 with the number keys,
first press the 100 key, and then
enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last
channel you were watching.
■ Audio Mute
Press MUTE to instantly mute the
sound. Press again to restore the
previous sound level.
■ Phones
Connect an earphone (not
supplied) or headphones (not
supplied) to the Phones Jack.
16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Picture Adjustment
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
SET UP FM
SELECT :
SET
:
: ACT I ON
END
: TUNER
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
1) Press
to select
VIDEO ADJUST.
2) Press to display
screen.
4
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
ADJUST :
END
: ACT I ON
Model PV-C921/PV-C931W
remote is shown here.
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
SET
:
END
: ACT I ON
Picture Adjustment
■ COLOR Control
Adjust color intensity.
■ TINT Control
Adjust for natural flesh tones.
5
1)Press
to select
an adjustment item.
(See below left.)
2)Press
to adjust.
To Reset Picture
Controls.
and to
Press
select and set
“NORMAL.”
All controls return to
their factory settings.
Press ACTION three times to exit.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by
adjusting both contrast and
color level in the proper
balance.
■ SHARPNESS Control
Adjust picture sharpness.
Note
Due to the earth’s magnetic fields, or magnetic
charge build-up from nearby electrical appliances,
color distortion may occur if the unit direction is
changed while it is on. To avoid this, position the unit
before turning it on. If this phenomenon does occur,
press the POWER-off and then on again.
17
TV Operation
<Model PV-C921/
PV-C931W screen shown>
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one
of 3 modes (2modes [PV-C911 only]).
(TV, Playback, or FM radio [PV-C921/PV-C931W only].)
(TV or Playback [PV-C911 only].)
You can also combine the On-Timer with a one
minute alarm that gradually increases in volume.
1
2
Press PROG
to display SET PROGRAM screen.
1)Press
to select
“ON TIMER.”
2)Press to display
ON TIMER screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
SELECT :
SET
:
END
: PROG
3
Ready Check List
The clock is set to correct time.
1) Press
to select
desired settings.
2) Press to set the
ON-TIMER TIME or
ON-TIMER mode.
ON T I MER
6:--AM
AM CH -ALARM : ON
SELE CT HOUR
SELECT :
SET
:
END
: PROG
• ON-TIMER mode
selection order
CH02
CH03
CH125
CH01
PLAY
FM9
FM8
FM1
(PV-C921/PV-C931W)
CH02
CH03
CH125
• Make sure a tape is
inserted if Playback mode
is selected.
• See “FM Radio” on page
22 for instructions on
how to preset FM
stations. (PV-C921/
PV-C931W only)
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
AUDIO IN
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
REC
ON TIMER
PROG TIMER
ACTION
CH
ON TIMER
Indicator
TIMER/FM (PV-C921/PV-C931W)
TIMER (PV-C911)
CH01
PLAY
(PV-C911)
4
ON T I MER
6:00AM CH08
ALARM : ON
Press
to select
ALARM “ON” or “OFF.”
ABC
SELE CT ALARM
CANCEL : ADD / DLT
SELECT :
SET
:
END
: PROG
When “ON” is selected,
an alarm will gradually increase in volume for one
minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
use
and
to move back and correct.
5
18
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights on the unit.
To Cancel ON-TIMER set,
Repeat steps 1 and 2.
Then, press ADD/DLT to clear the
time in step 3. Now, press PROG
to end. “ON TIMER END” briefly
appears on-screen.
Note
If no button on the remote or unit
(including a button used to turn off
the alarm) is pressed within 60
minutes after unit turns itself on, it
will turn itself back off.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
SLEEP TIMER
k List
orrect time.
This unit can be set for auto power off.
Press SLEEP repeatedly
to set SLEEP TIMER.
• Pressing DISPLAY with
sleep timer set displays
remaining time.
SLEEP TIMER 30
SLEEP TIMER 60
SLEEP TIMER 90
Press SLEEP repeatedly
until “SLEEP TIMER 00”
appears to cancel.
SLEEP TIMER 00
INSTANT ALARM
You can set a timer alarm up to 60 min. Useful when
you are cooking, etc.
Press TIMER/FM (PV-C921/PV-C931W)
[TIMER (PV-C911)] on the unit to display
the instant alarm CANCEL/SET screen.
5 : 20PM
CANCEL : ADD / DLT
02 : 00
SET : CH
KEY ON UN I T
3:00
the order shown left.)
Remaining Time
1:00 (one minute)
2:00
Press CH
on the
unit with CANCEL/SET
screen displayed to set
alarm. (Time changes in
one-minute
increase
until 10:00
• Pressing Press TIMER/FM (PV-C921/
PV-C931W) [TIMER (PV-C911)] repeatedly
on the unit will change display as follows.
five-minute
increase
until 30:00
(PV-C921/PV-C931W)
9:00
10:00
15:00
20:00
25:00
30:00
40:00
50:00
ten-minute
increase
until 60:00
60:00 (Max)
(PV-C911)
To cancel, press TIMER/FM (PV-C921/PV-C931W)
[TIMER (PV-C911)] then press ADD/DLT on the
remote while CANCEL/SET screen is displayed.
To increase timer in progress, repeat step 2. Time
will be rounded up to next 1, 5, or 10 minute interval.
(See chart left.)
<Example>
• If current time remaining is 12:15, countdown will
restart from 15:00.
• If current time remaining is 9:15, countdown will restart
from 10:00.
Note
While timer function is in progress,
you can change channels on the
unit with CH
while “CANCEL/
SET” screen is not displayed.
3
Alarm will sound at 0: 00.
Press any button to stop
• The volume of the alarm gradually increases for
one minute and then continues to beep until
any button is pressed.
19
TV Operation
Model PV-C921/PV-C931W
remote is shown here.
1
2
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing
impaired to enjoy selected programs, but also
makes useful information from TV stations
available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
SET UP FM
SELECT :
SET
:
: ACT I ON
END
: TUNER
1) Press
to select “TV.”
2) Press ACTION
to display SET
UP TV screen.
to
1) Press
select “CAPTION”.
2) Press to
display CAPTION
screen.
<Model PV-C921/
PV-C931W screen shown>
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: CAP C1
: CAP C1
SELECT :
SET
:
END
: ACT I ON
OFF
CAP C1
TEXT C2
1) Press
to
select CAPTION
MODE.
2) Press
repeatedly to
select mode.
(See left.)
Closed Caption Mode Selections
Caption Mode: CAP C1 or C2
A narration of selected TV programs is
displayed.
Check TV program listings for
CC(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
The lower half of the screen will be
blocked out. When the TV station
broadcasts information, such as
program listings, it will appear in this
space.
Caption Mode: OFF
Closed Caption / Text narration will not
be displayed.
NOTE :
The closed caption or text signal may be
broadcast over C1, C2, or both.
Also, text contents can vary so you may
wish to try different settings.
TEXT C1
CAP C2
5
Press ACTION three times
to return to the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record
: Record normally.
Closed Caption/ Text signal, if present, is recorded automatically.
Playback : Start playback. Do above steps to select desired caption mode.
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Caption On Mute Feature
Closed Caption narration, if available, is
displayed when MUTE button is pressed for
silence.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
1) Press
to
select “CAPTION”.
LOCK
N
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
SET UP FM
SELECT :
SET
:
END
: ACT I ON
: TUNER
2) Press
to
display CAPTION
screen.
<Model PV-C921/
PV-C931W screen shown>
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: OFF
: CAP C1
SELECT :
SET
:
END
: ACT I ON
5
1) Press
to
select CC ON
MUTE.
2) Press
repeatedly to
select desired
mode.
Model PV-C921/PV-C931W
remote is shown here.
NO
CAP C1
CAP C2
6
7
1) Press
to
select CAPTION
MODE.
2) Press
repeatedly to
select “OFF.”
• Each press of will
change the display as
shown left.
• The caption may be
broadcast over CAP
C1 or C2.
Press ACTION three times
to return to the normal screen.
Press MUTE to mute the sound and
display closed captioning.
• To cancel, press MUTE again.
21
TV Operation
3
SET UP TV
1) Press
to select “TV.”
2) Press ACTION
to display SET
UP TV screen.
FM Radio
<For Model PV-C921/PV-C931W only>
FM Radio is ...
This unit has an FM radio with built-in antenna, 9
station preset, and a band range of 87.5 ~ 108.1
MHz. You can even set the On-Timer (page 18)
to wake up to your favorite radio station.
3
FM Radio Setup
1
2
3
Press FM/TV on the remote or
press TIMER/FM twice on the unit
to display FM radio mode.
1 2 : 0 0PM
FM 1
87. 5MHz
1 2 : 0 0PM
FM 1
8 7. 7MHz
MEMORY : PUSH ADD / DLT KEY
Press a number
key (1~9) to select
the FM number.
1) Press CH
to select the
desired radio
station. (Each
press changes
frequency 200 KHz.)
1 2 : 0 0PM
FM 1
8 7. 7MHz
MEMOR I ZED
2) Press ADD/DLT
to set the radio
station.
Hold down CH or
for a few seconds,
then release to
quickly scan for FM
stations in your area.
To Make Corrections,
select station with a
number key, then do step • To cancel, press CH
3 again.
or while in
search mode.
To exit FM mode, press
FM/TV on the remote or
TIMER/FM twice on the unit.
4
SELECT :
SET
:
: ACT I ON
END
5
whichever
sounds the
best.
Press ACTION three times to end
setup.
Using FM Radio
1
2
Press FM/TV on the remote or
press TIMER/FM twice on the unit
to display FM radio mode.
22
Press a
number key
(1~9) to select
a preset FM
number
1 2 : 0 0PM
FM 1
87. 5MHz
(see steps 2 and
3 on this page).
To cancel, press FM/TV on the remote
or TIMER/FM twice on the unit.
POWER
Press ACTION
to display MAIN MENU.
“INT (INTERNAL)”
or “EXT
(EXTERNAL)”
■ For cable TV users ➔ “INT”
■ For antenna users ➔ “EXT”
VIDEO IN
1
2
1) Press
to
select FM
ANTENNA.
2) Press to
select
SET UP FM
FM ANTENNA
: INT
FM TRANSMITTER
: ON
SET UP FM TRANSMITTER
FM ANTENNA Setup
Make sure FM tuning is done
correctly (see FM Radio Setup).
1) Press
to
select SET
UP FM.
2) Press to
display screen.
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
: TUNER
V I DEO ADJUST
SET UP FM
SPEAKER
: ON
SELECT :
SET
:
: ACT I ON
END
VOL
CH
STOP/
EJECT
REW/
AUDIO IN
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
REC
ON TIMER
TIMER
PROG TIMER
ACTION
Notes
TIMER/FM
• FM radio cannot be recorded on a Video cassette.
• You may get better reception by repositioning the
unit.
• You cannot select FM Radio mode during playback
M A I N MENU
1) Press
or record, or while a blue back screen (PROG,
ACTION, MENU) is displayed.
to select “TV.”
VCR LANGUAGE
TV
2) Press ACTION • Once stations are set, the selected station and
current time are displayed when FM Radio mode
to display SET
EX I T
CH
CLOCK
is entered. To remove time, press DISPLAY.
SELECT :
UP TV screen.
If DISPLAY is pressed, the unit status screen
SET
: ACT I ON
appears.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
FM Transmitter
<For Model PV-C921/PV-C931W only>
Send Wireless
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
PLAY/
REPEAT
FF/
REC
TIMER/
FM
AUDIO IN
POWER
R EC
REC
ON TIMER
Within 33 feet Audio equipment
with FM Radio
PROG TIMER
ACTION
Carrier Frequency : 93 ~ 97, 99 ~ 103 MHz
FM Transmitter is ...
a feature whereby this unit’s sound can be
heard on an FM Radio. First, tune your radio to
a vacant station which has no radio broadcasts
between 93 ~ 97 or 99 ~ 103 MHz. Then, set
the combo to the same station. Now, fine-tune
this unit so the sound comes in clearly.
FM Transmitter Carrier Frequency Setup
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
4
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
: TUNER
V I DEO ADJUST
SET UP FM
: ON
SPEAKER
SELECT :
SET
:
: ACT I ON
END
SET UP FM
FM ANTENNA
: INT
FM TRANSMITTER
: OFF
SET UP FM TRANSMITTER
SELECT :
SET
:
: ACT I ON
END
1
2
Do “FM Transmitter Carrier
Frequency Setup” steps 1~3 at left.
SET UP FM
FM ANTENNA
: I NT
FM TRANSMITTER
: ON
SET UP FM TRANSMITTER
SELECT :
SET
:
END
: ACT I ON
3
Press ACTION three times
to end setup
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
1) Press
to select
SET UP FM.
2) Press to display.
screen.
1) Press
to select
SET UP FM
TRANSMITTER.
2) Press to display
screen.
Model PV-C921/PV-C931W
remote is shown here.
• When step 4 is done, if FM TRANSMITTER is
“OFF,” the unit is automatically set to “ON.”
5
SET UP FM TRANSMITTER
93MHz - 97MHz
99MHz - 103MHz
99MHz
6
1) Press
to select
the desired frequency
range. (93-97 or 99103 MHz)
2) Press
to select
the Carrier Frequency.
3) Press ACTION to set
the Carrier Frequency.
(The screen in step 4
is redisplayed.)
103MHz
To Make Corrections,
select frequency with CH
1) Press
to select
FM TRANSMITTER.
2) Press to select
“OFF” or “ON.”
TV Operation
1
2
Press ACTION
to display MAIN MENU.
FM Transmitter Control
, then repeat step 5.
Press ACTION four times
to end setup
Notes
• The Carrier Frequency shown by the selector
bar is a guide only. Please listen to the sound
and adjust accordingly.
• The unit will transmit sound when unit power is on
and “FM TRANSMITTER :ON” is selected.
• When unit power is turned off, “FM TRANSMITTER”
returns to “OFF” setting.
• The FM transmitter signal range varies
depending on installation and operating
requirements of your equipment.
• Interference occurs when you select CATV
channels 95, 96, or 97, while FM Transmitter is
operating.
• FM Transmitter will not work in FM Radio Mode.
• Please note the current FM Transmitter
capability is the maximum level allowed by FCC
standard for low power license-exempt radio
communication devices.
23
Timer Recording
You can set up to 8 programs to be recorded while
you are away.
1
2
Press PROG
to display SET PROGRAM screen.
1) Press
SET PROGRAM
TIMER PROGRAMMING.
T I MER PROGRAMMING
PROGRAMMING
ON TIMER
2) Press to display
screen.
SELECT :
SET
:
END
: PROG
3
to select
Ready Check List
All connections are made.
Your unit is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
• If a program is already in
memory, press
, and
to select an unused
program number.
CH
START
STOP
Press
to select
7 FR I --:-- --:-- -- and or to set the
TODAY
SLP
CATEGORY : N / A
------------------------ recording DATE.
DATE
AT E
SELE CT START DAT
SELECT :
SET
:
END
: PROG / ACT I ON
Example
Today’s
Date
8
7
9
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT
= Same time once a week
/
WEEKLY
(SAT)
2
1
31
SELECT
4
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00a
-- : --- : --- : --
CH SPD
08 SP
-- --- --- --
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
5
REW/
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
POWER
REC
REC
ON TIMER
PROG TIMER
PROG TIMER Indicator
WEEKLY
(SUN)
Press PROG
(or ACTION) to end
the program.
To Enter More Programs,
press
to select and
to set a blank program
number, and then repeat
step 3.
Press PROG twice (or ACTION) to exit
this mode.
• If you’re using a cable box, make
sure that it is tuned to the desired channel
and the power is left on for timer recording.
• PROG TIMER indicator lights on the unit.
Timer Recording Using
unit Buttons
You can set a Timer Recording
using ACTION key on the unit.
(See page 13.)
VOL
CH
STOP/
EJECT
REW/
ACTION
1 Press STOP/EJECT and REW
2
3
4
24
STOP/
EJECT
DAILY
• start time, stop time
• Channel (or LINE for outside source)
• Category [N/A (not applicable), SPORTS, MOVIE,
COMEDY, MUSIC, DRAMA]
• Speed (SP, LP, SLP)
DT
day
----
CH
ACTION
Repeat step 3 to set:
P
1
2
3
4
VOL
AUDIO IN
6
Selection Order
WEEKLY
(MON)
POWER
VIDEO IN
together without a tape inserted
to display MAIN MENU.
Press
+ - to select “VCR”
and STOP/EJECT and REW
together to display SET UP
VCR screen.
Press
to select “TIMER
PROGRAM” and + to display
the TIMER PROGRAM screen.
Repeat main steps 3 ~ 5.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few seconds
to cancel the Timer Recording.
• Any future daily or weekly recordings
will be performed as programmed.
Review, Replace or Clear Program
Contents : (Recording is not in progress)
1
2
Repeat steps 1 and 2 on page 24.
P
1
2
3
4
DT START STOP CH SPD
day 9 : 00p 12 : 00a 08 SP
8 10 : 00a 12 : 00p 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press
to select
the desired program.
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
3
To Replace program...
DATE
START
STOP
CH
8 SAT 9:00P 12:00A 08
ABC
TODAY
SP
CATEGORY : MOV I E
---------------------------------------------SELE CT START DATE
SELECT :
SET
:
: PROG / ACT I ON
END
1) Press to display.
2) Press
to select
and press or
to set new program
contents.
3) Press PROG
(or ACTION)
To Clear program...
DT START STOP CH
-- -- : -- -- : -- -8 10 : 00p 12 : 00a 125
10 8 : 00p 9 : 00p 10
SU 9 : 00p 10 : 00p L
SPD
-SP
SP
LP
Press ADD/DLT.
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
4
Model PV-C921/PV-C931W
remote is shown here.
Press PROG twice (or ACTION) to exit
this mode.
Notes
• 2 minutes before Timer recording is performed,
“PLEASE PREPARE FOR TIMER REC” appears
and/or the PROG TIMER Indicator flashes.
Be sure a cassette with record tab is loaded and the
unit is in Stop mode.
• If the start times of two programs overlap, the lower
numbered program will have priority.
• If the start time for a Timer Recording comes up
during a normal recording or One Touch Recording
(page 14), the Timer Recording will not be performed.
• If there is a power interruption of more than one minute,
the recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been
set, check all entries and make necessary corrections.
• When using DC Power supply, a Timer Recording can
not be performed if POWER on the unit is pressed OFF.
25
Timer Operation
P
1
2
3
4
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape.
When timer recordings are made, program index and information are also included.
(Only AC POWER) These index marks can be used to access or scan recordings.
Index Search
Go directly to the desired recording.
1
Press SEARCH in
Playback or Stop
mode to display
INDEX SEARCH
screen.
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
NEXT : SEARCH
EX I T : STOP
2
Press number
keys
to select the
recording number.
I NDEX SEARCH 3
I NDEX SEARCH
• To calculate
number, see below.
3
Press FF or REW
to start search.
I NDEX SEARCH
• Play begins at search
end. To search
forward or back 1
index, press FF or
REW while screen
left in displayed (10
seconds).
FORWARD SEARCH : FF
REVERSE SEARCH : REW
■ To calculate the Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
2
3
4
5
6
7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
2
3
4
5
6
Model PV-C921/PV-C931W
remote is shown here.
7
NOTE: indicates start points of each recording.
Notes
• Make each entry within 10 seconds, or the
Index Search mode will be canceled.
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
It is easy to detect the end of a recorded program
so that you may continue or begin a new recording.
1
2
Press SEARCH twice in Playback or
Stop mode to display PROGRAM END
SEARCH screen .
Press FF
to start search.
PROGRAM END SEARCH
SEARCH START : FF
EX I T : SEARCH
Example of Program End Search operation.
Fig.1
PLAYBACK DIRECTION
INDEX
Program 1
Press SEARCH button
FF
Program 2 or BLANK
End Point
Fig.2
Program 1
BLANK
INDEX
Program 2
Press SEARCH button
BLANK
End Point
FF
Fig.3 If search exceeds few seconds in BLANK area.
Press SEARCH button
Program 1
POWER
VIDEO IN
VOL
CH
STOP/
EJECT
REW/
PLAY/
REPEAT
FF/
REC
AUDIO IN
TIMER/
FM
POWER
POWER
REC
REC
ON TIMER
PROG TIMER
BLANK
INDEX
Program 2
FF
ACTION
End Point
REW FF
Upon locating end point...
The unit searches slightly past end point,
reverse searches, and plays the last few
seconds of the program, then stops.
Press SEARCH button
Notes
• If Program End Search is started very close
to an index mark, that mark may be
skipped over.
• To cancel, press PLAY or STOP.
27
Advanced Operation
21/PV-C931W
wn here.
Program End Search
Tape Operation (continued)
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV, blank tape is
Played for 5 minutes
➔ Power turns off
• This feature is canceled if any button is
pressed during above mode.
■ Auto Playback
Insert a tape in Power off mode
➔ Power turns on
• Playback begins if tape has no record tab.
• This feature cannot be activated when
the POWER button on the unit is turned
OFF (POWER indicator is not lit.)
■ Auto Rewind
Tape reaches its end
➔ Rewind, ➔ Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
➔ Rewind, ➔ Stop, ➔ Eject
Tape Position Display
To find out present tape position and amount of
tape remaining.
Tape position cannot be detected for
C-Cassettes, tapes under 30 minutes, and
some other tapes.
1
Press TAPE POSITION
to detect current tape position.
DETECT I NG TAPE POS I T I ON
SLP
R 120 MIN.
BEG I N
2
END
• “DETECTING TAPE
POSITION” is displayed only
when a cassette is first inserted
and it takes several seconds for
correct tape position to appear.
• The present tape position
indication and amount of tape
remaining (according to tape
speed) is displayed.
• Tape remaining time display
may not be precise.
Model PV-C921/PV-C931W
remote is shown here.
Press TAPE POSITION (or wait 5
seconds) to return to normal screen.
Note
• This function cannot display exact amount of
tape remaining for tapes 30 minutes or less,
or for tapes over 120 minutes in length.
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
)
Commercial Skip
Set to see a recording over and over.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP VCR
REPEAT PLAY
T I MER PROGRAMMING
T I ME STAMP
: OFF
: ON
SELECT :
SET
:
END
: ACT I ON
4
1)Press
to select “VCR.”
2)Press ACTION
to display SET
UP VCR screen.
Press ACTION twice
to end setup.
To quickly return to a specific tape counter location.
Press DISPLAY during playback
to display the Counter.
0 : 00 : 00
BEG I N
3
4
5
1
Press CM/ZERO repeatedly to
select skip time in Play mode.
• No indication appears.
1)Press
to
select “REPEAT
PLAY.”
2)Press to set
REPEAT PLAY
“ON” or “OFF.”
Zero Search
1
2
By pressing the CM/ZERO button in Playback
mode you can skip over 1 to 3 minutes of
recorded tape in just a few seconds.
Repeat Play Notes
• Playback repeats when tape end is
reached or unrecorded portion over 30
seconds is detected.
• During playback, you may also press
PLAY/REPEAT repeatedly on the unit to
select REPEAT “ON” or “OFF.”
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
Advanced Operation
21/PV-C931W
wn here.
Repeat Play
END
Continue playback, rewind, or
fast forward.
Press STOP.
1 : 23 : 45
BEG I N
•
Press CM/ZERO
in stop mode to
start ZERO
SEARCH.
END
: Present position mark
: Zero position mark
• Unit goes into FF or REW mode and
stops at the last point the Counter was
set to 0:00:00.
Zero Search Note
• If a blank portion exists on the tape, and
depending on the position of the mark,
the mark display may be out of position.
• When Zero Search is done in DC mode,
the counter position and the counter and
mark displays may be out of position.
29
Special VCR Features
Channel Caption is ...
Preset Caption
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
:
END
: ACT I ON
4
PRESET CAPT I ON
MANUAL CAPT I ON
-----
PBS
CNN
ESPN
HBO
1) Press
to select
CHANNEL CAPTION.
2) Press to display
screen.
• To create your own
captions, go to “Manual
Caption” on page 31.
PRESET CAPT I ON
ABC
CBS
FOX
NBC
Ready Check List
You need a list of stations and the
channel numbers you receive them on.
1) Press
to select
PRESET CAPTION.
2) Press to display
screen.
CHANNEL CAPT I ON
SELECT :
SET
:
END
: ACT I ON
5
1) Press
to
select “CH.”
2) Press ACTION to
display SET UP
CHANNEL screen.
Station names, e.g. ABC, TNN, etc.
are set so they will appear when a
channel is selected. Choose 24
preset names (Preset Caption), or
make up to 10 names of your own
(Manual Caption.)
-----
SELECT :
SET
:
END
: ACT I ON
PRESET CAPT I ON
62
TNT
4 2 CBC
UPN
-- CTV 2 1
52
WB
3 5 TSN
DSC
-- GLOB 1 2 3
CLEAR : ADD / DLT KEY
SELECT :
SET
:
END
: ACT I ON
1) Press
to select
a station.
2) Press to move
cursor to the right.
3) Press
to select
channel number.
4) Press to set
preset captions.
• Repeat step 5 until the
Caption List is
complete.
To Make Corrections
Press
Press
6
30
, then to select channel number.
to change, or ADD/DLT to delete.
Press ACTION four times
to end setup.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Manual Caption
1
2
Do “Preset Caption” steps 1~3
(page 30).
1) Press
to select
MANUAL CAPTION.
2) Press to display
screen.
CHANNEL CAPT I ON
PRESET CAPT I ON
PT I ON
MANUAL CAPT
SELECT :
SET
:
END
: ACT I ON
3
1) Press
to select
CH NUMBER.
2) Press to move
cursor to the right.
MANUAL CAPT I ON
CH NUMBER
CAPT I ON
----
O2
SELECT :
SET
:
: ACT I ON
END
MANUAL CAPT I ON
CAPT I ON
CH NUMBER
A---
O2
CLEAR : ADD / DLT
SELECT :
SET
:
END
: ACT I ON
Model PV-C921/PV-C931W
remote is shown here.
1) Press
to select
and to enter your
caption.
• Characters change in the
following order.
A
B
C
9
Z BLANK
2 1 0 /
&
!
• Press repeatedly to move the
cursor to “CH NUMBER.” Repeat
steps 3 and 4 as desired.
To Make Corrections
Press
Press
5
, then to select channel number.
to change, or ADD/DLT to delete.
Press ACTION four times
to end setup.
31
Advanced Operation
4
• Channels already set
and channels deleted
from Channel Memory
are not displayed.
• You can set a total of ten
channel captions with up
to four characters each.
Special VCR Features (continued)
Weak Signal Display ON/OFF
When “ON” is selected, the picture is displayed even
when a broadcast signal is weak or non-existent.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
:
END
: ACT I ON
1) Press
to select “CH.”
2) Press ACTION
to display SET
UP CHANNEL
screen.
1) Press
to
select
WEAK SIGNAL
DISPLAY.
2) Press to set
“ON” or “OFF.”
Notes
• “ON” = Picture is displayed regardless of
signal condition, and may not
always be clearly visible.
“OFF”= Screen turns solid blue when
signal is absent or weak.
• If unit is connected to equipment which
has blue back feature, selecting “ON” will
have no effect on the other equipment.
POWER
VIDEO IN
4
VOL
CH
STOP/
EJECT
REW/
AUDIO IN
PLAY/
REPEAT
FF/
REC
TIMER/
FM
POWER
POWER
REC
ON TIMER
PROG TIMER
ACTION
Press ACTION twice
to return to the normal screen.
REC
VCR Lock
All operations are prohibited except Timer
recording and tape eject. Useful for families
with small children.
In stop mode, hold
down REC on the
VCR LOCK ACT I VATED
unit without a
cassette inserted for 7
seconds to turn “ON.”
Please ignore “NO
VCR LOCK OFF
CASSETTE” warning.
Repeat above with
or without cassette
to turn “OFF.”
• VCR Lock is canceled automatically
after about 24 hours if clock is set.
• This feature cannot be activated when
POWER on the unit is turned OFF
(POWER indicator is not lit.)
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Time Stamp Feature
Ready Check List
The clock is set to correct time.
The record tab is in place.
This unit writes program data (see example
below) for about the first 10 seconds of every
recording. The information is then displayed
about 10 seconds after playback begins.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP VCR
REPEAT PLAY
T I MER PROGRAMMING
T I ME STAMP
SELECT :
SET
:
END
: ACT I ON
: OFF
: ON
1) Press
to select “VCR.”
2) Press ACTION
to display SET
UP VCR screen.
1)Press
to
select TIME
STAMP.
2)Press to set
“ON” or “OFF.”
• When “OFF” is selected, the program data
is written on the tape, but will not be displayed.
4
Press ACTION twice
to return to normal screen.
Model PV-C921/PV-C931W
remote is shown here.
Advanced Operation
<Time Stamp Example >
Normal/ One
Touch Recording
Timer Recording
When Clock is not set...
33
V-Chip Control Feature
V-Chip Control Feature is...
This unit has a built-in V-Chip Control which allows
you to block unwanted TV usage based on
US MOVIES and US TV PROGRAMS Ratings.
Process of V-Chip Control Feature
Enter Code
Blocking
Setup
Enter Secret Code
A 4-digit code must be entered to view a blocked
program or change rating settings.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
SET UP FM
SELECT :
SET
:
END
: ACT I ON
: TUNER
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
1) Press
to select
LOCK.
2) Press to display
screen.
<Model PV-C921/
PV-C931W screen shown>
4
LOCK
ENTER 4-D I G I T CODE
---ENTER : 0 - 9
: ACT I ON
END
To Make Corrections
Press repeatedly to
move the cursor.
Press number keys to
make the correction.
5
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE :
: ACT I ON
END
34
1) Press number keys
to enter your secret
code.
2) Enter same code
again for confirmation.
• Step 2) not necessary
when changing rating
or secret code.
• Take care that you are
not observed entering
the secret code.
Press to display US
Ratings menu (see
page 35).
Or
Press ACTION three
times to exit.
Changing your secret code
• You will need your current code.
Do steps 1 ~ 4. In step 5, press
ADD/DLT to clear current code.
Repeat steps 4 and 5 to enter
new code.
Notes
• DO NOT forget your secret code.
• Once ratings are set, restricted
tapes or programs cannot be
accessed unless the secret code
is entered.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
If LOCK menu is not displayed, do
“Enter Secret Code” steps on page 34.
Setup US MOVIES Ratings
1
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET
:
END
: ACT I ON
1) Press
to select
US MOVIES.
2) Press to set “ON”
or “OFF.”
■ “ON” ➔ V-Chip Control is activated.
■ “OFF” ➔ V-Chip Control is deactivated.
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing Canadian
tapes or broadcasts.
2
3
Model PV-C921/PV-C931W
remote is shown here.
GENERAL AUDIENCE:
All ages admitted.
PG PARENTAL GUIDANCE:
Some material may not be
suitable for children.
PG-13 PARENTS CAUTIONED:
Some material may be
inappropriate for children under 13.
R RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
NC-17 OVER AGE 17 ONLY:
No one 17 and under admitted.
X ADULTS ONLY:
V I EW NR PROGRAMS? : YES
G
UNLOCKED
PG
PG-13
R
NC-17
X
CONTA I NS NO RAT I NG
SELECT :
SET :
END
: ACT I ON
1) Press
to select
CHANGE SETTINGS.
2) Press to display
screen.
1) Press
to select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some movies, such as old movies
or foreign movies usually have no ratings.
4
G
5
V I EW NR PROGRAMS? : YES
G
UNLOCKED
PG
PG-13
R
NC-17
X
GENERAL AUD I ENCE
SELECT :
SET :
END
: ACT I ON
to select
1) Press
and to set
ratings to be
blocked.
(See ratings chart
next page.)
Press ACTION to redisplay LOCK
menu and continue with US TV
PROGRAMS Ratings Setup (next page).
Or, press ACTION four times to exit.
35
Advanced Operation
US MOVIES RATINGS
LOCK
US MOVIES
: OFF
CHANGE SET
SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET
:
END
: ACT I ON
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do
“Enter Secret Code” steps on page 34.
Setup US TV PROGRAMS Ratings
1
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET
:
END
: ACT I ON
1) Press
to select
US TV
PROGRAMS.
2) Press to set
“ON” or “OFF.”
■ “ON” ➔ V-Chip Control is activated.
■ “OFF” ➔ V-Chip Control is deactivated.
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing Canadian
tapes or broadcasts.
2
3
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET
:
END
: ACT I ON
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
CONTA I NS NO RAT I NG
SELECT :
SET :
END
: ACT I ON
1) Press
to select
CHANGE SETTINGS.
2) Press to display
screen.
1) Press
to select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, emergency information
usually have no ratings.
4
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L
TV-PG
V S L
TV-1 4
V S L
TV-MA
FOR ALL CH I LDREN
SELECT :
SET :
END
: ACT I ON
D
D
Note
You may select from
standard TV ratings
(chart 1), or customize to
a specific content rating
(chart 2).
5
36
1) Press
to select
and to set ratings
to be blocked.
(See ratings charts
at right.)
US TV PROGRAMS RATINGS:
Chart 1
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
FOR ALL CHILDREN:
Content specifically geared to
young viewers ages 2-6.
FOR AGE 7 AND OLDER:
May contain mild physical or
comedic violence which may
frighten children under 7.
GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language,
and more intense violence.
MATURE AUDIENCE:
May contain mature themes,
profane language, graphic violence,
and sexual situations.
US TV PROGRAMS RATINGS:
Chart 2
FV
V
S
L
D
Fantasy Violence
Violence
Sexual Situations
Adult Language
Sexually Suggestive Dialogue
• Ratings highlighted
in Green will be
blocked. Ratings in
white letters will not
be blocked.
Press ACTION four times
to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
<When V-Chip Control is activated>
• If a program or movie
ABC
exceeds the ratings you
have set, a message will
PROGRAM RAT I NG EXCEEDED
appear on a black
RAT I NG : PG-1 3
background and sound is
ACCESS CODE
---muted.
ENTER : 0-9
To View a Blocked Program / Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in
the Blocking Message screen.
• V-Chip Control is reactivated when
power is turned off or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-4 page 34).
Then, set US MOVIES and/or US TV
and keys.
PROGRAMS to “OFF” using
(Ratings set on pages 35, 36 are retained and
will be in effect when V-Chip Control is
activated again.)
STOP
1 1 : 0 0AM
ABC
0 : 12 : 34
SP
RAT I NG : PG-1 3
1 1 : 0 0AM
NO V-CH I P DATA
Model PV-C921/PV-C931W
remote is shown here.
ABC
0 : 12 : 34
SP
• If DISPLAY is pressed,
when V-Chip has not
been setup, “NO V-CHIP
DATA” is displayed onscreen.
37
Advanced Operation
STOP
• If DISPLAY is pressed,
even when V-Chip control
is deactivated, rating is
displayed on-screen.
On-Screen Display (OSD)
VCR Status & Clock Display
Press DISPLAY
to display or remove the overlay.
Function Status
Channel Caption
(See pages 30, 31.)
Current Time
REC
0 : 25
Rec Time Remaining
(OTR mode only, see
page 14.)
ABC
1 2 : 0 0PM
-0 : 1 2 : 3 4
SP
Counter
Tape Speed
12 / 18 / 2001 TUE
12 : 0 0PM - 1 : 0 0PM
CH 0 8 ABC MOV I E
Time Stamp Data (See page 33.)
Blue Screen Display
Whenever a blank section of a tape comes
up in Play mode, or when the selected
channel has no broadcast signal with the
Weak Signal Display set to “OFF” (see
page 32), the screen will turn solid blue.
Channel & Function Display
When a function button is pressed (PLAY,
FF, etc.) or you change channels, the unit
mode or channel number will be displayed.
(Some station names may also appear if
Channel Caption is set. See pages 30, 31.)
Dew Detection System
To prevent damage to your tapes, this unit
is equipped with a dew detection system.
When moisture condensation is detected
inside the unit, “DEW” will appear
on-screen for a few seconds. If a tape is
inserted, it will be ejected.
Also, VCR functions will be non-operational
until dew condition passes.
Press DISPLAY to see if dew condition still
exists. In order to avoid this condition, try
not to move the unit directly from a cold
place to a warm place. TV functions are
not affected.
DEW
08
ABC
PLAY
38
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Warning and Instruction Displays
These displays will alert you of a missed operation or provide further instructions.
Page
OSD
Caution
NO CH FOUND PLEASE CHECK
ANTENNA CABLE CONNECTION THEN
PUSH CH UP KEY AGAIN
• If no active channels are found for
PLEASE SET CLOCK BEFORE
PROGRAMMING
• If you attempt to set or review a Timer
Recording, or set the On-Timer and the Clock
is not set...
CHECK CASSETTE RECORD TAB
• If you press REC, and a cassette is inserted
with no record tab...
TO CANCEL TIMER REC HOLD DOWN
STOP KEY FOR APPROX 3 SEC
• If you press STOP during a Timer
Recording...
25
NO CASSETTE
PLEASE INSERT A CASSETTE
• If you press PLAY, FF, REW, or REC
without a cassette inserted...
14
DEW
• If moisture condensation is detected inside
the unit...
38
VIDEO HEADS MAY NEED CLEANING
PLEASE INSERT HEAD CLEANING
CASSETTE OR REFER TO MANUAL
END: PLAY KEY
• If head cleaning becomes necessary while
playing back a tape...
41
VCR LOCK ACTIVATED
• If you press a function button other than
STOP/EJECT or POWER while the unit is in
VCR Lock mode...
CHANNEL MEMORY...
5,8 - 11
8 - 13
4, 14
32
For Your Information
39
Operation Differences Using AC or DC Power
This unit is equipped to be operated on either AC or DC power. However, there are some
differences in unit operation depending on which power supply is used.
Notes
• The unit will accept commands from the remote control only when POWER on the unit is
turned ON (POWER indicator is lit.)
• When POWER on the unit is OFF (DC power source), it’s the same as if the unit were unplugged.
Therefore, all memory data, i.e. clock data, etc. is erased in approximately one minute.
• If there is a loss in battery voltage of more than 30 seconds, the unit automatically shuts off.
AC Power Supply is Used
DC Power Supply is Used
• If POWER on the remote control is
pressed OFF during rewind, the power
will shut off but the rewind will
continue (Memory Rewind.) If it is
pressed during recording, the
recording will continue.
• If POWER on the remote control is
pressed OFF during rewind, the
rewind is terminated and the unit shuts
off. If it is pressed while recording, the
recording is terminated and the unit
shuts off.
• When STOP is pressed, the cylinder
continues to rotate for 5 minutes.
• When STOP is pressed, the cylinder
stops.
• If the AC cord is unplugged and then
plugged back in, the unit will be in
OFF condition.
• If POWER on the unit is pressed OFF,
the unit will be in Stop mode when
turned back on.
• If the DC cord is unplugged, and then
plugged back in; within one minute,
Play and Rec mode will continue. All
other functions will change to Stop
mode.
If unplugged for over one minute, the
unit will be in STOP mode when
plugged back in.
• If POWER on the unit is pressed OFF,
OTR (One Touch Recording) is
continued.
• If POWER on the unit is pressed OFF,
OTR (One Touch Recording) will be
canceled.
• If POWER on the unit is pressed OFF,
Timer Recording will be performed.
• If POWER on the unit is pressed OFF,
while a Timer Recording is in
progress, the Timer Recording will be
canceled.
• If POWER on the unit is pressed OFF
during rewind, the power will shut off
but the rewind will continue (Memory
Rewind.)
• If POWER on the unit is pressed OFF
during rewind, the rewind is
terminated and the unit shuts off.
WARNING:
• There may be an excessive drain on the battery if the unit is used along with such
power consuming things as fog lamps, air conditioner, power windows, etc.
• Never watch or operate the unit while driving a vehicle.
• Avoid leaving the unit in places of extreme heat, such as inside a hot vehicle, or in
direct sunlight as this may damage the unit.
40
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Unit Information
Specifications
Head Cleaning
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Head Clog Sensor
During playback this screen appears if
clogging is detected. To remove screen,
press PLAY on the remote or unit.
• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape directions carefully. Excessive
use of head cleaning tape can shorten the video
head life.
V I DEO HEADS MAY
• If head clog symptoms persist,
NEED CLEAN I NG
PL EASE I NSERT HEAD
contact your nearest Factory
CLEAN I NG CASSETTE
OR REFER TO MANUAL
Service Center or authorized
Service Center. (See page 43.) END : PLAY KEY
Build-in Head Cleaner <For Model PV-C911 only>
A clean video head helps produce a clear
picture. So, we have equipped your unit with a
built-in, non chemical head cleaning system
that helps prevent clogging of the video heads.
Cleaning is performed each time you load or
unload a video cassette.
Note: This feature is preventative only. If your
video heads are seriously clogged,
consider the use of a chemical
nonabrasive head cleaning kit or take
your unit to a Service Center.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight Saving Time.)
■ Spring (First Sunday in April)
DST : ON ➜ Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST : ON ➜ Turns clock back one hour.
• If your area does not observe Daylight Saving
Time, select DST:OFF.
• Keep these time changes in mind when
programming the unit for timer recordings.
1 Hour
2 Hours
LP (Long Play)
2 Hours
4 Hours
SLP (Super Long Play)
3 Hours
6 Hours
VCR
Video Recording System: 2 rotary heads helical
scanning system
Audio Track:
1 track
Tuner
Broadcast Channels:
VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels:
Midband A through I (14 ~ 22)
Superband J through W
(23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A(01)
Ultraband 65 ~ 94, 100 ~ 125
FM Radio
Band range:
87.5 ~ 108.1 MHz
(PV-C921/PV-C931W)
FM Transmitter
Band range:
93 ~ 97, 99 ~ 103 MHz
(PV-C921/PV-C931W)
General
Power Source:
120 V AC, 60 Hz (AC)
12V/24V (DC)
Power Consumption:
Power on
Approx. 63 watts (AC)
Approx. 59 watts (DC)
Power off
Approx. 3.5 watts (AC)
Approx. 0.8 watts (DC 12V)
Approx. 1.5 watts (DC 24V)
Television System:
EIA Standard NTSC color
Speaker:
1 piece
Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity:
10 % ~ 75 %
Weight:
9.1 Kg (20.1 lbs.)
Dimensions:
302 (W) X 327 (H) X
335 (D) mm
11-7/8” (W) X 12-7/8” (H)
X 13-3/16” (D)
Note: Designs and specifications are subject to
change without notice.
Features for a Quality Picture
Only use tapes with the
mark in this unit.
Type of Video Cassette
Tape Speed
Setting
T60
T120
T160
SP (Standard Play)
9 inch measured
diagonal 90° deflection
Picture Tube
2 Hours
40 Minutes
5 Hours
20 Minutes
8 Hours
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 number key on
the remote control or CH
on the unit until the
picture clears up. To return to Auto Tracking, press
POWER off, then on again a few seconds later.
41
For Your Information
Record/Playback Time
Display
Picture Tube:
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
No power…
Monitor
Correction
• Completely insert Power Plug into an AC outlet or when using
the DC Car battery cord, check to see it the fuse is blown.
• Set POWER button to ON.
Correction
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 8 - 11)
No picture or sound...
• Completely insert Power Plug into an AC outlet. (Or use the DC Car
Battery cord.)
Poor picture with normal sound... • Set POWER button to ON.
• Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the
SET UP TV menu. (P. 17)
Poor sound with normal picture...
• Adjust VOLUME control. (P. 16)
Poor TV reception...
• Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P. 17)
No color or poor color...
• Adjust TINT and COLOR controls in the SET UP TV menu. (P. 17)
Ghost (multiple) images...
TV programs cannot be watched... • Install a directional antenna.
• Make sure the selected channel is in unit’s memory. (P. 12, 13)
Channel cannot be selected...
• Only the channel being recorded can be viewed on this unit.
VCR
Correction
TV program cannot be recorded... •
•
Timer recording cannot be
•
•
performed…
•
•
No playback picture, or the playback
picture is noisy or contains streaks...
VCR cannot be controlled...
Remote Control
Unit cannot be controlled...
ACTION, PROG and FM/TV
buttons cannot be selected...
Miscellaneous
Video cassette cannot be
inserted...
Video cassette cannot be
removed...
Tape cannot be ejected or
inserted...
Video cassette ejects when a
recording is started, or the power
is turned off for timer recording...
In Stop mode, the VCR motor
(CYLINDER) continues to rotate...
VCR cannot be controlled...
•
•
•
•
Make sure your antenna system (TV or CABLE), is correctly set. (P. 8-11)
Make sure cassette record tab is intact. (P.4)
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to channel to
be recorded.
Set recording Start/Stop times correctly. (P. 24 - 25)
Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during a Timer
recording even after power is restored.
Adjust TRACKING control in either direction. (P. 41)
Try Head Cleaning. (P. 41)
Make sure VCR LOCK is set to off. (P. 32)
Make sure unit is not in a Timer Record operation.
Correction
• Aim remote at remote sensor on unit (P. 7) so that signal is
unobstructed.
• Inspect the remote batteries. (P. 4)
• Make sure VCR LOCK is set to off. (P. 32)
• Exposing unit remote sensor to direct fluorescent or outdoor light may
cause signal interference.
• Check remote batteries.
Correction
• Insert the cassette window side up; record tab facing you.
• Completely insert Power Plug into an AC outlet. (Or use the DC Car
Battery cord.)
• Try ejecting or inserting the tape again after turning POWER off, then
back on.
• Make sure cassette record tab is intact. (P. 4)
• To enable Quick Play mechanism, the VCR cylinder will rotate for
about 3 minutes. This reduces response time from Stop to Play mode
and from Play to Rewind Search mode.
• Make sure VCR LOCK is set to off. (P. 32)
If you cannot resolve the problem, please call the Customer Satisfaction Center for
product assistance at 1-800-211-PANA(7262).
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : [email protected]
42
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Service Center List
For Product Information, Operating Assistance, Literature Request, Dealer
Locations, and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm Saturday-Sunday 9 am-7 pm, EST.
or send e-mail to : [email protected]
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your nearest
servicenter by visiting our Web Site.
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Factory Servicenters Locations
CALIFORNIA
GEORGIA
MINNESOTA
TEXAS
6550 Katella Avenue
Cypress, CA 90630
800 Dubuque Avenue
S. San Francisco,
CA 94080
3878 Ruffin Road
Suite A
San Diego, CA 92123
8655 Roswell Road
Suite 100
Atlanta, GA 30350
7850-12th Avenue South
Airport Business Center
Bloomington, MN 55425
13615 Welch Road
Suite 101
Farmers Branch,
TX 75244
ILLINOIS
OHIO
1709 North Randall Road
Elgin, IL 60123
2236 Waycross Road
Civic Center Plaza
Forest Park, OH 45240
FLORIDA
MASSACHUSETTS
PENNSYLVANIA
3700 North 29th Avenue
Suite 102
Hollywood, FL 33020
60 Glacier Drive,
Suite G
Westwood, MA 02090
2221 Cabot Blvd. West
Suite B
Langhorne, PA 19047
WASHINGTON
20425-84th Avenue
South
Kent, WA 98032
HAWAII
99-859 Iwaiwa Street
Aiea, Hawaii 96701
Phone (808) 488-1996
Fax (808) 486-4369
As of June 2001
43
For Your Information
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985
Phone (787) 750-4300 Fax (787) 768-2910
Limited Warranty
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation
of America, One Panasonic Way
Secaucus, New Jersey 07094
Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.
AVE. 65 de Infantería, Km. 9.5 San Gabriel
Industrial Park Carolina, Puerto Rico 00985
PANASONIC/QUASAR Video Products
Limited Warranty
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the
Warrantor”) will repair or replace this product with new or refurbished parts or equivalent product, free of charge, in
the USA or Puerto Rico, in the event of a defect in materials or workmanship as follows (all time periods commence
from the date of the original purchase):
PARTS
ONE (1) YEAR, EXCEPT
CCD IMAGE SENSOR
CCD IMAGE SENSOR
- SIX (6) MONTHS
LABOR
NINETY (90) DAYS
SERVICE
Carry-In or Mail-In
CONTACT NUMBER
1-800-211-PANA(7262)
DVD/VCR DECK ONE (1) YEAR
ONE (1) YEAR, EXCEPT
DIGITAL STILL
CCD IMAGE SENSOR
CAMERA
CCD IMAGE SENSOR
- SIX (6) MONTHS
A/V MIXER
ONE (1) YEAR
NINETY (90) DAYS
NINETY (90) DAYS
Carry-In or Mail-In
1-800-211-PANA(7262)
TV/VCR, TV/DVD ONE (1) YEAR,
EXCEPT CRT
TV/DVD/VCR
COMBINATION CRT - TWO (2) YEARS
NINETY (90) DAYS
NINETY (90) DAYS
CRT - NINETY (90) DAYS
PRODUCT
CAMCORDER
Carry-In or Mail-In
1-800-272-7033
NINETY (90) DAYS
NINETY (90) DAYS
1-800-211-PANA(7262)
Carry-In or Mail-In
Carry-In: 21” CRT and 1-800-211-PANA(7262)
Smaller
In-Home or Carry-In:
22” CRT and Larger
In-Home or Carry-In 1-888-843-9788
NINETY (90) DAYS
ONE (1) YEAR,
CRT - NINETY (90) DAYS
EXCEPT CRT
CRT - TWO (2) YEARS
Batteries (if included) - New rechargeable batteries in exchange for defective rechargeable batteries for ten (10)
days. Non-rechargeable batteries are not warranted.
Tape (if included) - New video cassette tape in exchange for a defective video cassette tape for five (5) days.
Memory cards (if included) - Exchange defective item for new one for ninety (90) days.
In-home, carry-in or mail-in service, as applicable, in the USA can be obtained during the warranty period by
contacting a Panasonic Services Company (PASC) Factory Servicenter listed in the Servicenter Directory.
Or call toll free contact number listed above, to locate an authorized PASC Servicenter. Carry-in or mail-in service
in Puerto Rico can be obtained during the warranty period by calling the Panasonic Sales Company telephone
number listed in the Servicenter Directory.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of the date of the original
purchase is requires before warranty service is rendered.
This warranty only covers failures due to defects in materials and workmanship, which occur during normal use and
does not cover normal maintenance, including, but not limited to, video and audio head cleaning. The warranty
does not cover damage which occurs in shipment, or failures which are caused by products not supplied by the
warrantor, or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration,
modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of
consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, commercial
use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than
a PASC Factory Servicenter or a PASC authorized Servicenter, or damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
WITHOUT LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF THIS PRODUCTS,
OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE
LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the
exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so
the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may
also have other rights, which vary, from state to state. If a problem with this product develops during or after the
warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to the Consumer Affairs Department at the Panasonic Consumer Electronics Company address above.
SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORKMANSHIP AS DETERMINED
BY THE WARRANTOR, IN ITS SOLE DISCRETION, ARE NOT COVERED. COSTS OF SUCH SERVICE CALLS
ARE THE RESPONSIBILITY OF THE PURCHASER.
warvid 02/ 12/ 2001
TV/HDR
COMBINATION
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Spanish Quick Use Guide/Guía para rápida consulta
Conexión de la Antena Interior
Inserte la antena varilla (suministrada) en
el receptáculo de la parte trasera de la
combinación de VCR/TV. Luego, conecte
los dos alambres al transformador de 300
ohmios-75 ohmios (suministrado.)
Entonces, conecte el transformador ala
parte transera de la combinación de VCR/
TV como se muestra. Ahora, despliegue la
antena y ajuste su longitud, dirección y
ángulo para la más clara imagen.
Antena Interior
(incluido)
Transformador
de 300-75
ohmios
(incluido)
Conexión a la fuente de alimentación
Ud. podrá llevar su combinación de VCR/TV a donde ud. va con dos diferentes formas de
alimentación. Ud. podrá conectar su cable de C.A. (corriente alternada) incorporado a
cualquier fuente de CA. Cuando está viajando, conecte su cable para batería de coche al
enchufe de su encendedor de cigarrillo. para su seguridad de uso y para evitar daños al
aparato, por favor siga las instrucciones y conexiones con cuidado.
■ Conexión del cable de CA (incorporado)
1. Conecte el cable de CA incorporado al enchufe de
entrada CA en la parte trasera del aparato como está
demostrado.
2. Conecte el cable de CA al enchufe de CA su pared.
■ Conexión del cable para la batería de coche
(incorporado)
1. Conecte el cable para batería de coche al enchufe
de entrada CC en la parte trasera del aparato como
está demostrado.
2. Arranque su vehículo.
• No conecte su cable al enchufe del encendedor
de cigarrillo antes de arrancar su vehículo.
3. Desconecte el encendedor de cigarrillo y conecte
el enchufe de su cable para batería.
■ Cambio del fusible de cable para
Si su fusible de seguridad se ha cortado, cambie como sigue al siguiente.
1. Destornille la tapa.
2. Cambie su fusible con otro fusible de 125V 10A.
• Use sólo fusibles con las especificaciones correctas.
3. Reponga la tapa.
Fusible Tapa
Guía para rápida
consulta
NOTAS IMPORTANTES:
• Este cable sólo se puede usar en vehículos con batería de
12V o 24V (toma a tierra negativo.) Verifique en su manual
de instrucciones de su vehículo.
• Use solamente el cable para batería de coche incorporado
con su combinación de VCR/TV.
• Para evitar la disminución del voltage, no extienda el cable
para batería de coche desde usando otro cable de extensión.
• Cuando no está usando el aparato, desconecte el cable para
batería de coche desde el enchufe del encendedor para
cigarrillo para evitar la descarga de la batería de su automovil.
45
Spanish Quick Use Guide/Guía para rápida consulta
Como realizar la
Configuración Inicial
1
2
Presione POWER para encender el
videograbador combinado.
Cuando encienda
el VCR por
primera vez,
aparecerá la
pantalla SELECT
LANGUAGE.
• Si ajusta el idioma incorrecto, realice
los pasos de la página 9 “Reajuste de
todas las Funciones de Memoria de
la unidad”.
• Active la caja de cables y ajústela al
canal PBS en su huso horario.
Si usted utiliza receptor DSS, este debe
estar apagado.
Presione CH ▲
para seleccionar
Inglés (English).
O
Presione CH ▼
para seleccionar
Español.
O
Presione VOL +
para seleccionar
Francés (Français).
Aparecerá la
pantalla CHANNEL
/ CLOCK AUTO
SET.
3
4
6 / 7 / 2000 M I E 12 : 00PM
HORA VERAN I EGA: ACT
CANAL F I JADO : CA 1 0
F I JAC I ON AUTOMATICA
COMPLETO
TERMINAR : OPR I M I R CH UP
46
Presione la tecla CH
▲ para iniciar el
funcionamiento de
CHANNEL / CLOCK
AUTO SET. El ajuste
del CHANNEL /
CLOCK se lleva a cabo
automáticamente, si la
configuración se ha
terminado, se visualiza
la pantalla siguiente.
Si aparece la
pantalla “FIJACION
AUTOMATICA DEL
RELOJ
INCOMPLETO”,
ajuste el reloj
utilizando los
procedimientos de
“AJUSTE MANUAL
DEL RELOJ”
mostrados en la
página 9.
Ajuste Manual del Reloj
Si el ajuste automático del reloj no se ha
completado, ajuste el reloj manualmente de
la siguiente manera:
1) Presione la tecla ACTION en el control
remoto para visualizar la pantalla del
menú RELOJ.
2) Presione ▲▼ para seleccionar el mes y
para ajustar. De la misma forma,
seleccione y ajuste la fecha, año, hora y
DST (Hora de Verano).
3) Presione dos veces la tecla ACTION
para poner el RELOJ en marcha y salir.
Ajustar de nuevo el reloj
1
2
3
Presione ACTION para exhiba el
menú.
Presione ▲▼
para seleccionar
“RELOJ”.
Presione ACTION.
F I JAR RELOJ
F I JAC I ON AUTOMAT I CA
MANUAL
AJUSTE ZONA HORA : 0
ELEG I R :
F I JAR :
TERM I NAR : ACT I ON
Presione ▲▼ para
seleccionar
“MANUAL” y luego
presione .
4
Presione ▲▼ y
para seleccionar y
ajustar la hora y la
fecha.
5
Presione ACTION dos veces para que
el reloj comience a funcionar y salir
desde este modo.
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
Operaciones básicas para
la reproducción
1
2
■
■
■
■
■
■
■
■
Inserte un cassette.
• El videograbador combinado se enciende
automáticamente.
Presione PLAY.
• La reproducción comienza
automáticamente si el casete no tiene la
lengüeta para prevención de grabación.
Para encontrar una escena en particular
Búsqueda hacia adelante ➔ Presione FF
Búsqueda hacia atrás ➔ Presione REW
Para ver una imagen fija (congelada) ➔
Presione PAUSE/SLOW
Para ver en cámara lenta ➔ Mantenga
pulsado el botón PAUSE/SLOW en el modo
de imagen fija
Para ver imágenes cuadro a cuadro ➔
Presione PAUSE/SLOW en el modo de
imagen fija
Para parar ➔ Presione STOP
Para rebobinar la cinta ➔ Presione REW
Para hacer avanzar la cinta rápidamente ➔
Presione FF
Para expulsar la cinta ➔ Presione EJECT
en el control remoto o STOP/EJECT en el
videograbador combinado
Operaciones básicas para
la grabación
1
2
3
Inserte un casete con la lengüeta
para prevención de grabado.
4
Comience la grabación.
Presione REC.
• El videograbador combinado se enciende
automáticamente.
Seleccione el canal.
Presione CH ▲▼ o las teclas
numéricas correspondiente.
Seleccione la velocidad de
grabación.
Grabación con temporizador
1
2
Ajuste la fecha de
grabación.
1) Presione ▲▼
para seleccionar.
2) Presione o
para ajustar.
3
• 1 - 31 = Grabación única
• DIARIO = a la misma hora de lunes a viernes
• SEMANAL = a la misma hora una vez a la
semana
Fecha de hoy
Repita el paso 3 para ajustar:
hora de comienzo, hora de parada, canal (o LINEA
para una fuente exterior), categoría [N/O (no
aplicable), DEPORTE, CINE, COMEDIA, MUSICA,
DRAMA], velocidad (SP, LP, SLP)
Termine el programa.
Presione PROG
(o ACTION.)
Para introducir
más programas.
presione ▲▼ y para
seleccionar y ajustar el
número de programa
en blanco, y luego
repita los pasos 3 y 4.
1:30
5
Salga de este modo.
Presione PROG dos veces (o
ACTION.)
• Si está usando un decodificador de TV
cable, asegúrese que se encuentra en el
canal deseado y que la alimentación
queda conectada para grabar con
temporizador.
• El indicador PROG TIMER se enciende
en el videograbador combinado.
Guía para rápida
consulta
■ Para parar ➔ Presione STOP.
■ El videograbador combinado
deja de grabar a una hora prefijada.
(Grabación de un toque)
Presione REC repetidamente para
ajustar la hora de grabación (30 min
Grabación normal 0:30 1:00
- 4 horas.)
2:00
TEMPOR l ZADOR
ENCENDIDO AUTOMATICO
Exhiba
TEMPORIZADOR.
1) Presione ▲▼
para seleccionar.
2) Presione para
exhibir.
• Si ya existe un programa en la memoria, presione
▲▼ y para seleccionar un número de programa
sin usar.
4
• Para editar partes no deseadas de una
grabación, presione PAUSE/SLOW para
hacer una pausa durante la grabación.
• No podrá ver otro canal durante la grabación.
3:00
F I JAR PROGRAMAC I ON
ELEG l R :
F I JAR :
TERM l NAR : PROG
Presione SPEED.
SP = reproducción normal
LP = reproducción larga
SLP = reproducción super larga
• La velocidad seleccionada debe aparecer
en la pantalla.
4:00
Exhiba FIJAR PROGRAMACION.
Presione PROG.
47
Index
A
B
C
D
E
F
H
I
L
LSQT0603A
N
O
Accessories ........................................... 4
Audio Mute ............................................ 16
Auto Operation Functions ..................... 28
Batteries ................................................. 4
Before Requesting Service .................. 42
Before Using ........................................... 4
Blocking Message ................................ 37
Blue Screen Display ............................. 38
Build-in Head Cleaner .......................... 41
Caption On Mute .................................. 21
Channel .................................... 8 - 13, 38
Channel Caption ................................... 30
Clock ..................................................... 12
Closed Caption ..................................... 20
Commercial Skip .................................. 29
Connecting to a Power Source ............. 5
Connections ................................ 5, 8 - 11
Connections, DSS / Cable Box ..... 10 -11
Connections, Outdoor Antenna ....... 8 - 9
Copy Your Tapes (Dubbing) ................. 15
DST (Daylight Saving Time) ................. 41
Eject tape .............................................. 14
Fast Forward ......................................... 14
FM Radio .............................................. 22
FM Transmitter ..................................... 23
Forward Search .................................... 14
Frame by Frame Advance ...................... 14
Front Panel Indicators ........................... 7
Function Display ................................... 38
Head Cleaning ...................................... 41
Important Safeguards and Precautions ... 2
Index Search ......................................... 26
Indoor Antenna Connections .................. 5
Initial Setup for ANT. / Cable Connection ... 8
Initial Setup for DSS / Cable box Connection .. 10
Input Mode ............................................ 15
INSTANT ALARM ................................. 19
Language ........................................ 8 - 13
Limited Warranty .................................. 44
Location of Controls ......................... 6 - 7
NIGHT Mode ......................................... 16
100 Key ................................................. 16
One Touch Recording .......................... 14
ON-TIMER with Alarm .......................... 18
Operation Differences Using AC or DC Power .. 40
P
Phones .................................................. 16
Playback ............................................... 14
Picture Adjustment ............................... 17
Program End Search ............................ 27
Q Quality Picture ...................................... 41
R Rapid Tune ........................................... 16
Rec(ord) ................................................ 14
Record/Playback Speed Settings ......... 41
Remote Control Buttons ........................ 6
Repeat Play .......................................... 29
Reset Language, Channels, Clock ...... 12
Reset unit ............................................... 9
Reverse Search .................................... 14
Rewind .................................................. 14
S Secret Code .......................................... 34
Service Center List ............................... 43
SELF-DEMO Mode ................................ 4
Sleep Timer .......................................... 19
Slow Motion .......................................... 14
Spanish Quick Use Guide .................... 45
Special VCR Features .......................... 30
Specifications ....................................... 41
Still Picture ............................................ 14
STOP .................................................... 14
T Tape Erasure Prevention ...................... 4
Tape Position Display ........................... 28
Time Zone Adjust ................................. 13
Time Stamp .......................................... 33
Timer Program Review, Replace, Clear .... 25
Timer Recording ................................... 24
Timer Recording Cancellation .............. 25
TV Operation ........................................ 16
TV Timer Features ................................ 18
U Unit, Front/Rear view .............................. 7
US MOVIES/TV PROGRAMS Ratings ... 35,36
V VCR Lock .............................................. 32
VCR Status & Clock Display ................ 38
V-Chip Control Feature ........................ 34
W Warning and Instruction Displays ........ 39
Weak Signal Display ON/OFF .............. 32
Z Zero Search .......................................... 29
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería. Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
P
Printed in Indonesia
LSQT0603A
S0202-0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement