Panasonic PVV4622 Operating Instructions

Panasonic PVV4622 Operating Instructions
Initial Initial
SetupSetup
(Hookup)
(Connection)
Video Cassette Recorder
Operating Instructions
Model No. PV-V4622
Basic
Timer
Operation Recording
As an ENERGY STAR ® Partner, Matsushita Electric Corporation of
America has determined that this product or product model meets the
ENERGY STAR ® guidelines for energy efficiency.
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
LSQT0509B
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
1
2002/05/23, 18:28
For Your
Information
VCR Plus+, ALLSET and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
under license from Gemstar Development Corporation.
Advanced
Operation
Connections and Initial Setup Procedures are on pages 8 to 11.
Important Safeguards and Precautions
FOR YOUR SAFETY, READ AND RETAIN
ALL SAFETY AND OPERATING
INSTRUCTIONS. HEED ALL WARNINGS
IN THE MANUAL AND ON THE UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from the power source indicated
on the unit or in this manual. If necessary,
have your Electric Utility Service Company or
Video Products Dealer verify the power source
in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this Video product comes
with either a polarized power cord plug (one
blade is wider than the other), or a three-wire
grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you
cannot fully insert the plug, try reversing it. If it
still will not fit, have an electrician install the
proper wall outlet. Do not defeat the safety feature
by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding
outlet. If necessary, have an electrician install the
proper outlet. Do not defeat the safety feature by
tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they
are not likely to have anything rest on them, roll
over them, or be in the way of walking traffic. If
an extension cord is used, make sure it also
has either a polarized or grounded plug and that
the cords can be securely connected. Frayed
cords, damaged plugs, and damaged or cracked
wire insulation are hazardous and should be
replaced by a qualified service technician.
Overloaded outlets and extension cords are fire
hazards and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If they are blocked,
heat build-up inside the unit can cause failures
that may result in a fire hazard or heat damage
to cassettes. For protection, follow these rules:
a. Never cover ventilation slots or the unit
while in use, or operate the unit when placed
on a bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless proper ventilation is provided.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near any kind of
heater or radiator, in direct sunlight, inside a
closed vehicle, etc.. Do not move the unit
suddenly between areas of extreme temperature
variation. If the unit is suddenly moved from a
cold place to a warm place, moisture may
condense in the unit and on the tape.
6 TO AVOID PERSONAL INJURY
• Do not place unsecured equipment on a
sloping surface.
• Do not place this unit on any support
that is not firm, level, and adequately
strong. The unit could fall causing
serious injury to a child or adult
and damage to the unit.
• An appliance and cart combination
should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the
appliance and cart combination to overturn.
• Carefully follow all operating instructions and
use the manufacturer's recommended
accessories when operating this unit or
connecting it to any other equipment.
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded so as
to provide some protection against built up static charges
and voltage surges. Section
810 of the National Electrical
Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen to
fall. When installing an outside antenna, extreme care should be
taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.
USING THE VIDEO UNIT
If the unit has been in storage or moved to a new location,
refer first to the INSTALLATION section of these safeguards.
1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR
MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected
by a qualified service technician before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT OPERATE
if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.
• Never drop or push any object through openings in the unit.
Some internal parts carry hazardous voltages and contact
can cause electric shock or fire hazard.
• Avoid placing the unit directly above or below your TV set
as this may cause electrical interference. Keep all magnets
away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated cloth
to gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into the unit
and cause electrical shock. Any substance such as wax, adhesive
tape, etc. may mar the cabinet surface. Exposure to greasy, humid,
or dusty areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating
instructions, this Video product does not operate properly,
do not attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by
the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as
described in the manufacture’s service literature to ensure
that the video unit is in safe operating condition.
NEC - NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
2
V4622 P1-21 (2nd) [LSQT0509B].p65
2
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
2002/05/23, 18:28
Safety Precautions
WARNING: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
CAUTION: To prevent electric shock, match wide blade of plug
to wide slot, fully insert.
Avertissement: Afin de prévenir tout risque d’incendie ou de
chocs électriques, ne pas exposer cet appareil à
la pluie ou à une humidité excessive.
Attention: Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
Note to CABLE system installer:
This reminder is provided to call the CABLE system installer’s attention to
Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in
Canada) that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system
of the building, as close to the point of cable entry as practical.
FCC Warning: Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate.
3
V4622 P1-21 (2nd) [LSQT0509B].p65
3
2002/05/23, 18:28
Before Using
Congratulations
Prevent Accidental Tape Erasure
on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring
you years of enjoyment. Please fill in the
information below. The serial number is on
the tag located on the back of your VCR.
•
•
•
•
•
•
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
PV-V4622
Serial No.
Record Tab
Screw driver
Accessories
Remote Control
Break off the tab to
prevent recording.
Batteries 2 “AA”
LSSQ0314
RF Coaxial Cable
VJAS0196
To record again
Cover the hole
with cellophane tape.
Record/ Playback Time
To order accessories, call toll free
1-800-332-5368.
Loading the Batteries
1) Open cover.
Only use tapes with the
Tape Speed
Setting
2) Insert
batteries as
marked.
Type of Video Cassette
T60
SP
1 Hour
(Standard Play)
LP
(Long Play)
mark in this unit.
2 Hours
SLP
3 Hours
(Super Long Play)
T120
T160
2 Hours
2 Hours 40 Minutes
5 Hours
4 Hours 20 Minutes
6 Hours
8 Hours
3) Close cover.
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese
batteries.
4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
4
2002/05/23, 18:28
Table of Contents
Timer Recording .............................................................. 16, 17
Timer Recording Using VCR Plus+ System ............... 18 ~ 21
Basic
Timer
Operation Recording
Reset Language, Channels, Clock, VCR’s Output Channel ... 12, 13
Playback a Tape .................................................................... 14
Record on a Tape .................................................................. 15
Initial Setup
(Connection)
Important Safeguards and Precautions ............................ 2, 3
Accessories ............................................................................. 4
Loading the Batteries .............................................................. 4
Prevent Accidental Tape Erasure .......................................... 4
Record/ Playback Time ........................................................... 4
Location of Controls ........................................................... 6, 7
➛VCR➛
➛TV Connection .............. 8, 9
Initial Setup for ANT./ Cable➛
➛VCR➛
➛TV Connection .... 10, 11
Initial Setup for DSS/ Cable Box➛
Multi-Brand Control Feature ........................................... 22, 23
Advanced Connections (Cable/DSS) ................................... 24
MTS Broadcast/ VHS Hi-Fi Stereo System .......................... 25
Tape Operation (
and
) .. 26 ~ 31
Special VCR Features ................................................... 32 ~ 35
Copying Your Tapes (Dubbing) ............................................ 36
Advanced
Operation
VCR & Cassette Information................................................. 37
On-Screen Displays (OSD) ................................................... 38
Before Requesting Service................................................... 39
Limited Warranty/ Customer Services Directory .......... 40, 41
Spanish (Español) Quick Use Guide.............................. 42, 43
Index ....................................................................... Back Cover
For Your
Information
5
V4622 P1-21 (2nd) [LSQT0509B].p65
5
2002/05/23, 18:28
Location of Controls
Remote control Buttons
LIGHT
EJECT
(Remote buttons light up)
(Ejects tape)
POWER
TV (mode)
(Enables TV functions)
(Turns VCR off/on)
VCR (mode)
DSS/CABLE mode
(Enables VCR functions)
(Enables DSS/CABLE functions)
VCR/TV
INPUT
(For TV or VCR mode)
PLAY (Plays a tape)/
(For LINE or channel)
PROGRAM/VCR+
FAST FORWARD/SEARCH
(Displays Timer Program screen)
(Fast forwards tape/ forward visual search)
NUMBER Keys
REWIND/SEARCH
(Selects channel directly)
(Rewinds tape/ reverse visual search)
STOP (Stops tape)
ADD/DELETE
(Adds or deletes a channel)
Remote keys
COMMERCIAL ADVANCE/
ZERO SEARCH
PLAY, STOP, REW, and FF
function as
operation
keys when menus are displayed.
(Set MOVIE ADVANCE/ Zero search)
TAPE POSITION
ACTION
(Locates tape position)
(Displays menu)
SEARCH/ ENTER
COUNTER RESET
(Set search system /Tunes TV channel)
(Resets counter to zero)
MOVIE ADVANCE
PAUSE/SLOW
(Set MOVIE ADVANCE)
(Displays still, frame by frame,
or slow motion picture)
SPEED
(Changes tape speed)
DISPLAY
RECORD
(Displays VCR status)
(Records a program, etc.)
SAP/Hi-Fi
CHANNEL /
TRACKING/ V-LOCK
(Selects audio mode for play or
record)
(Selects channel/ reduces picture
noise during Play and Slow mode)
VOLUME +/(Adjusts TV volume)
SHUTTLE Ring
(Variable speed search)
Light Tower Universal shuttle Remote Control
LIGHT button: When pressed, available buttons light and selected mode button (TV, VCR, or DSS
CABLE) flashes 5 seconds. If no button is pressed, light goes out in 5 seconds. Also,
hold down a button to confirm the selected mode (mode button flashes) in the dark.
EJECT button: Press to eject tape. EJECT is not available during recording.
Front View of the VCR
Cassette Compartment
STOP/EJECT
PLAY
POWER
FAST
FORWARD/
SEARCH
Video
Input
Connector
Audio Input
Connector (L/R)
6
CHANNEL /
TRACKING/ V-LOCK
Remote
Sensor
RECORD
REWIND/
SEARCH
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
6
2002/05/23, 18:28
Multi Function Display
Power Indicator
Lights up when power is on.
Initial Setup
(Connection)
Timer Indicator
Lights up when the VCR is set for Timer
Recording, or when One Touch Recording (OTR)
is used. Flashes when a Timer Recording is set,
but tape has not been inserted into the VCR.
TIMER
VCR
A
M
Hi-Fi
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays VCR
status when a function button is pressed.
Briefly displays the channel number, or “L1” or
“L2” when a channel or line input is selected.
Briefly displays the recording speed when
SPEED is pressed.
VCR Indicator
Lights up when the
VCR/TV selector is
set to VCR.
Hi-Fi Indicator
Lights up when Hi-Fi audio
is monitored in Playback
Mode.
Rear View of the VCR
Audio Input
Connector (L/R)
AC Power Plug
VHF/UHF Antenna
Input Terminal
Video Input Connector
AUDIO
IN FROM ANT.
R
L
VIDEO
IN 1
Video Output
Connector
OUT
VHF/UHF
OUT TO TV
VHF/UHF Antenna
Output Terminal
Audio Output
Connector (L/R)
Note
• While plugged into an AC outlet, the VCR consumes 3.0 W of electrical power in off mode.
7
V4622 P1-21 (2nd) [LSQT0509B].p65
7
2002/05/23, 18:28
Initial Setup for ANT./Cable ➛ VCR ➛ TV Connection
Please make all cable or antenna connections before plugging into the AC outlet.
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.
How to Connect
1
Connect cable from Antenna/Cable to VCR’s IN FROM ANT.
jack.
2
Connect VCR’s OUT TO TV jack to TV’s ANT. IN jack with
included RF Cable accessory.
VCR
IN FROM ANT.
TV
1
IN from
ANT./CABLE
OUT TO TV
2
VHF/UHF
Doing Initial Setup (Ready to Play)
1
2
Turn TV on and tune to channel 3.
Plug VCR Power Cord into AC wall
outlet. VCR comes on and auto
channel and clock set starts.
• If screen at right does not appear,
check VCR - TV connection and, if
TV is tuned to channel 3, try
switching it to channel 4.
• To change VCR’s output channel,
please refer to “VCR’s Output
Channel” on page 13.
WARNING
When using “Nut type” RF coaxial cables,
tighten with fingers only. Overtightening may
damage terminals.
8
Plugging the AC Power Plug into an AC outlet
CH AUTO SET PROCEEDING
CANCEL : STOP
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
8
2002/05/23, 18:28
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
3
VCR
C/A
CLOCK
CH
9 /29 / 2002 SUN 2 : 20PM
DST : ON
SETT I NG : CH 10
SELECT/
SET
:PLAY
:STOP
:REW
:FF
AUTO CLOCK SET
COMPLETED
4
SELECT CONNECTION screen is
displayed.
* to select connection
Press
“VCR TV” or “VCR CABLE/DSS
BOX TV”, and press to set.
Initial Setup
(Connection)
Settings are made automatically.
When setup is done, this screen
appears.
ACTION
VCR C / A CLOCK CHANNEL
SELECT CONNECTION
VCR TV
CABLE / DSS BOX VCR TV
VCR CABLE / DSS BOX TV
SELECT :
SET :
: ACT I ON
EXIT
If “AUTO CLOCK SET IS
INCOMPLETE” appears, manually
set clock. See below right.
VCR
C/A
CLOCK
CH
AUTO CLOCK SET IS
INCOMPLETE
Manual Clock Set
If Auto Clock Set was incomplete.
Press ACTION on remote to display
CLOCK screen.
a
PLEASE SET CLOCK BY
PRESSING ACTION KEY
VCR
C/A
CLOCK
CH
:
1/ /
DST:ON
SELE CT MONTH
SELECT :
SET :
EXIT
: ACT I ON
b
Press
to select the month and
to set. In the same manner, select and
set the date, year, time, and DST
(Daylight Saving Time).
VCR
C/A
CLOCK
CH
9 /29 / 2002 SUN 12:00PM
DST:ON
SET COMPLETED
:
SET
START : ACT I ON
c
Press ACTION to start clock, and go
to step 4 above left.
9
V4622 P1-21 (2nd) [LSQT0509B].p65
9
2002/05/23, 18:28
Initial Setup for DSS/Cable Box ➛ VCR ➛ TV Connection
Please make all cable or antenna connections before plugging into the AC outlet.
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.
How to Connect
1
Connect the OUT Jack on your cable box to the IN FROM ANT.
terminal on the VCR with the RF Cable.
2
Connect the OUT TO TV terminal on the rear of VCR to the ANT.
IN terminal on TV using the RF Cable (included accessory).
TV
IN FROM ANT. Cable TV
Converter Box
VCR
OUT TO TV
2
VHF/UHF
1
IN from
ANT./CABLE
WARNING
When using “Nut type” RF coaxial cables,
tighten with fingers only. Overtightening may
damage terminals.
Doing Initial Setup (Ready to Play)
1
2
Turn TV on and tune to channel 3.
• Turn on your cable box and set it to
your Public Broadcasting Station (PBS)
channel in your time zone. If you use a
DSS receiver, it must be turned off.
Plug VCR Power Cord into AC wall
outlet. VCR comes on and auto
channel and clock set starts.
• If screen at right does not appear,
check VCR - TV connection and, if
TV is tuned to channel 3, try
switching it to channel 4.
• To change VCR’s output channel,
please refer to “VCR’s Output
Channel” on page 13.
10
Plugging the AC Power Plug into an AC outlet
CH AUTO SET PROCEEDING
CANCEL : STOP
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
10
2002/05/23, 18:28
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
3
Settings are made automatically.
When setup is done, this screen appears.
C/A
CLOCK
CH
9 /29 / 2002 SUN 2 : 20PM
DST : ON
SETT I NG : CH 10
AUTO CLOCK SET
COMPLETED
4
SELECT/
SET
:PLAY
:STOP
:REW
:FF
SELECT CONNECTION screen is
displayed.
* to select connection
Press
“CABLE/ DSS BOX VCR TV” and
press to set.
Initial Setup
(Connection)
VCR
ACTION
VCR C / A CLOCK CHANNEL
SELECT CONNECTION
VCR TV
CABLE / DSS BOX VCR TV
VCR CABLE / DSS BOX TV
SELECT :
SET :
: ACT I ON
EXIT
Confirm the output channel of your
to
cable box or DSS receiver. Press
select the same channel as the cable
box or DSS receiver output channel.
Press to enter.
Manual Clock Set
If Auto Clock Set was incomplete.
Press ACTION on remote to
display CLOCK screen.
a
VCR C / A CLOCK CHANNEL
SELECT CONNECTION
CABLE / DSS BOX VCR TV
VCR
C/A
CLOCK
CH
:
1/ /
CABLE / DSS BOX OUTPUT CH
CH 0 1
DST:ON
SELE CT MONTH
SELECT :
SET :
: ACT I ON
EXIT
SELECT :
SET :
EXIT
: ACT I ON
If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock.
See right.
VCR
C/A
CLOCK
b
CH
AUTO CLOCK SET IS
INCOMPLETE
Press
to select the month
and to set. In the same
manner, select and set the
date, year, time, and DST
(Daylight Saving Time).
VCR
PLEASE SET CLOCK BY
PRESSING ACTION KEY
C/A
CLOCK
CH
9 /29 / 2002 SUN 12:00PM
DST:ON
SET COMPLETED
SET
:
START : ACT I ON
c
Press ACTION to start clock,
and go to step 4 above left.
11
V4622 P1-21 (2nd) [LSQT0509B].p65
11
2002/05/23, 18:28
Reset Language, Channels, Clock,
1
2
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
: ACT I ON
EXIT
Press ACTION*
to display menu.
Language
Channels
1) Press
to select
language item.
1) Press
to
select CHANNEL.
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
: ACT I ON
EXIT
2) Press
repeatedly.
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
: ACT I ON
EXIT
For English
VCR C / A RELOJ
CA
REPETICION
:INACT
SELLO DE TIEMPO
:ACT
AVISO/CONT.REMOTO :ACT
APAGADO AUTOMATICO :INACT
VCR/TV AUTO
:ACT
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA :3
ELEGIR :
FIJAR :
SAL I R : ACT I ON
For Spanish
MAGNETO. C / A HORL. CA
REPRISE LECTURE
: NON
HORODATEUR
: OUI
MESSAGE D’ ERREUR
: OUI
COUPURE AUTO
: NON
MAGNETO. /TELE AUTO :OUI
LANGUAGE/IDIOMA : FRANÇAIS
CA SORTIE : 3
SEL.
:
REGLER:
QUITTER : ACT I ON
3) Press ACTION to
exit.
Clock
1) Press
CLOCK.
to select
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
VCR C / A
CLOCK
CH
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
SELECT :
: ACT I ON
EXIT
SELECT :
: ACT I ON
EXIT
2) Press
to select
“ANTENNA,” then
press to set your
antenna system
(“TV” or “CABLE”).
2) Press
to select
“MANUAL,” and press
. (For Auto Clock Set,
select “AUTO CLOCK
SET.”)
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
VCR C / A
CLOCK
CH
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
SELECT :
: ACT I ON
EXIT
SELECT :
SET :
: ACT I ON
EXIT
3) Press
to select
“AUTO SET,” then
press .
• If you use Cable Box,
set it to the PBS channel
in your time zone.
VCR C / A CLOCK
CHANNEL
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
VCR
C/A
CLOCK
CH
9 /29 / 2002 SUN 2 : --PM
DST : ON
SELECT HOUR
SELECT :
SET :
EXIT
: ACT I ON
CH AUTO SET PROCEEDING
CANCEL : STOP
For French
VCR’s O
• After Channel Auto Set is
finished, Auto Clock Set
will be performed.
and
to
3) Press
select and set the
date, time, and DST
(Daylight Saving
Time).
4) Press ACTION to start
the clock and exit this
mode.
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
12
2002/05/23, 18:28
k,
TV/VCR
VCR’s Output Channel
POWER
*Important: If a remote control button does not
work when pressed, press the VCR
button on the remote and try the
button again.
Time Zone Adjust
to select
SELECT/
SET
:PLAY
:STOP
:REW
:FF
VCR’s Output
Channel
(Only when Auto Clock is set.)
1) Press
CLOCK.
VCR
NUMBER
keys
ACTION
1) Press
to select
VCR’S OUTPUT CH.
SELECT :
EXIT
: ACT I ON
2) Press
to select
“TIME ZONE ADJUST.”
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SET :
SELECT :
EXIT
: ACT I ON
/
2) Press .
VCR
CLOCK
CH
VCR C / A
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
CH
Basic
Operation
ADD/DLT
VCR C / A
CLOCK
CH
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
C/A
CLOCK
CH
Add or Delete a Channel
To add channel:
Select channel with NUMBER keys
and press ADD/DLT.
IF YOU PRESS ACTION
KEY, VCR ’ S OUTPUT CH
SWITCHES TO CH 4.
CHANNEL 08 ADDED
SELECT :
SET :
EXIT
: ACT I ON
and press to
subtract or add
hour(s) as necessary.
3) Press ACTION.
3) Press ACTION.
VCR
C/A
CLOCK
CH
PLEASE TUNE YOUR TV TO
CH 4.
• “TIME ZONE ADJUST”
returns to “0” if clock is
set manually.
To delete channel:
Select channel with CH / or
NUMBER keys and press ADD/DLT.
CHANNEL 08 DELE TED
DST (Daylight Saving Time)
After 3 seconds
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :4
SET :
SELECT :
: ACT I ON
EXIT
• To Make Corrections,
repeat steps 1) ~ 3).
VCR auto adjusts clock for DST.
(p. 9.)
Spring (First Sunday in April)
DST:ON ➛ Sets clock ahead one hour.
Autumn (Last Sunday in October)
DST:ON ➛ Turns clock back one hour.
• If your area does not observe
Daylight Saving Time, select
DST:OFF.
• Keep these time changes in mind
when programming VCR for
timer recordings.
13
V4622 P1-21 (2nd) [LSQT0509B].p65
13
2002/05/23, 18:28
Playback a Tape
Ready Checklist
All connections are made (p. 8, 10, 24).
TV and VCR are plugged in.
TV is on and tuned to CH 3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR)
1
Insert a tape,
2
Press PLAY to play tape.
• If tape has no rec. tab (p. 4), auto play begins.
Special Features During Play
EJECT
Forward/ Reverse scene search
➛ Press FF or REW.
➛ Press PLAY to release.
After search has begun, each additional press
of FF or REW changes speed as shown below.
[SLP] : Approx. 21X ↔ Approx. 43X
[LP] : Approx. 9X ↔ Approx. 15X
[SP] : Approx. 7X ↔ Approx. 13X
PLAY
REW
• VCR power comes on. “VCR” lights on Multi
Function Display. If Auto VCR/TV (p. 35) is
set to “OFF,” press VCR/TV until “VCR”
lights on the Multi Function Display.
FF
• If picture is interrupted at 43X, 15X, or 13X
speed, speed changes to 21X, 9X, or 7X.
• It may take a moment for 43X, 15X, or 13X search
to start while tape condition is being determined.
• 43X, 15X, or 13X search may not be possible
with some tapes.
STOP
Notes
PAUSE/
SLOW
• Picture interruption may occur with some TVs.
• FF and REW search speed may vary depending
on current tape position.
Still (Freeze) picture
➛ Press PAUSE/SLOW.
➛ Press PLAY to release.
Frame by Frame picture
➛ Press PAUSE/SLOW in Still mode.
➛ Press PLAY to release.
Slow Motion picture
➛ Hold down PAUSE/SLOW in Still mode.
➛ Press PLAY to release.
Notes
Playback using VCR controls
1 Insert a tape.
2 Press PLAY.
• These features work best in SP or SLP mode.
• The sound will be muted.
• To reduce picture noise, see “Manual Tracking
Control” on page 37.
• After the VCR is in Still or Slow mode for 3 minutes,
it will switch to Stop mode automatically to protect
the tape and the video head.
3
Multi Function Display
Press STOP/EJECT to stop and/
or eject tape.
Rapid Rewind/ Fast Forward
(E.g., T-120 tape rewinds in approx. 1 minute.)
Press REW or FF in Stop mode.
Notes
• Rewind or FF starts after VCR detects tape
length. This may take a moment.
• Rew/ FF speed slows down at start and end
portions of the tape.
Note
Remove loose or
peeling labels from tapes
to prevent tape jam.
14
Press STOP
to stop tape.
Press EJECT on remote,
or STOP/EJECT on VCR to eject tape.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
14
2002/05/23, 18:28
*Important:
Record on a Tape
Ready Checklist
All connections are made (p. 8, 10, 24).
TV and VCR are plugged in.
TV is on and tuned to CH3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR)
VCR/
TV
SPEED
PAUSE/
SLOW
1
Insert a tape with a record tab (p. 4).
2
Press CH
* or NUMBER keys
to select the channel.
• For “LINE” input, see p. 36.
• For channel over 100, first press 100
key then the other 2 digits.
3
Press SPEED
to select the record speed (p. 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Speed appears on-screen and on Multi
Function Display.
4
Press REC
to start recording.
• To edit, press PAUSE/SLOW to pause,
and again to resume recording.
5
Press STOP
to stop recording.
CH
CH
REC
• VCR power comes on.
“VCR” lights on Multi Function
Display. If Auto VCR/TV (p. 35) is set to
“OFF,” press VCR/TV until “VCR”
lights on the Multi Function Display.
Basic
Operation
STOP
If a remote control button does not work
when pressed, press the VCR button on
the remote and try the button again.
One Touch Recording (recording in progress),
• VCR shuts off after the preset record length.
➛ each press of REC adds 30 min. to the
recording length up to 4 hours.
Record using VCR controls
2 Select
Channel.
1 Insert 4 Press
a tape.
Multi Function
Display
REC
to start
Recording.
5 Press
STOP/
EJECT to stop.
This video recorder, equipped with HQ
(High Quality) system, is compatible
with existing VHS equipment. Only use
tapes with the
mark. Only tapes
tested and inspected for use in 2, 4, 6,
and 8 hour machines are
recommended.
Record one station, watch another,
➛ press VCR/TV (“VCR” goes out on Multi
Function Display),
➛ select channels at TV (recording
continues).
• Watching one channel and
Note
recording another is NOT
possible when using a Cable
Box or a Satellite Receiver.
Select channels at VCR,
• Other channels cannot be viewed during
recording.
➛ press VCR/TV (“VCR” lights up on Multi
Function Display),
➛ select channels at VCR.
Note
• After 5 min. in Pause mode, VCR
stops to protect the tape and the
video head.
15
V4622 P1-21 (2nd) [LSQT0509B].p65
15
2002/05/23, 18:28
Timer Recording
Ready Checklist
POWER
All connections are made (p. 8, 10, 24).
TV and VCR plugged in and turned on.
VCR/TV selector set to “VCR.”
Clock set correctly.
Tape has rec. tab (p. 4).
Remote is in VCR mode. (Press VCR)
SELECT/
SET
VCR/
TV
:PLAY
:STOP
:REW
:FF
1
2
PROG/
VCR+
Press PROG/VCR+* button
to display PROGRAM.
Press
to display Program
13 SAT --:-- --:-- -- screen.
TODAY
VCR Plus+
PROG.
DATE
START STOP
CATEGORY : N/A
LIST
CH
SLP
SELECT :
EXIT
: PROG
3
VCR Plus+
PROG.
LIST
DATE
START STOP
CH
13 SAT --:-- --:-- -TODAY
CATEGORY : N/A
SELECT START DATE
SLP
SELECT :
SET:
END
: PROG
Example
1) Set record DATE,
press
to select:
1~31= one time, or
DAILY= MON~ FRI, or
WEEKLY= same time
each week and press
to set.
• See selection order
below left.
2) To set remaining
items, press
to
select and press to
WEEKLY
WEEKLY
WEEKLY
set START/ STOP
(SAT)
(MON)
(SUN)
times, CH (channel)
**Category Items
or LINE input (p. 36),
N/A (not applicable),
Category** and tape
SPORTS, MOVIE, COMEDY,
speed (SP, LP, SLP).
MUSIC,
DRAMA
Notes
Press PROG/VCR+
button to end the program.
• If you are using a Cable Box,
Today
14 15
13 SELECT
VCR Timer Programming Channel
(Step 3) must be set to the Cable
Box output channel and your
Cable Box must be manually set
to the desired channel. The Cable
Box must be left on.
• If a power interruption occurs
while programming the timer, the
timer program(s) may be canceled.
If “TIMER PROGRAMS WERE LOST
DUE TO POWER INTERRUPTION”
appears on-screen, please reenter
the timer programs.
16
4
31
/
1
2
12
Selection Order
VCR Plus+
PROG.
DT START
STOP
13 2 : 00 P 3 : 20P
-- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
LIST
CH SPD
02 SLP
-- --- --- --
CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
5
DAILY
To Enter More Programs,
press
to select and
press to set an unused
program number and
repeat step 3.
Or
Press PROG/VCR+
button again to exit.
Press POWER off
to set the Timer Recording.
(“TIMER” lights up on Multi Function Display.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
16
2002/05/23, 18:28
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Review, Replace or Clear Program Contents:
(Recording is not in progress)
1
VCR Plus+
PROG.
DT START
STOP
7
9 : 00A 12 : 00A
8 10 : 00P 12 : 00P
10
8 : 00P 9 : 00P
SU
9 : 00P 10 : 00P
LIST
CH SPD
08 SP
02 SP
10 SP
L1 LP
1) Press
PROG/VCR+ button.
2) Press
to select LIST.
SELECT :
EXIT
: PROG
2
VCR Plus+
PROG.
DT START
STOP
7
9 : 00A 12 : 00A
8 10 : 00P 12 : 00P
10
8 : 00P 9 : 00P
9 : 00P 10 : 00P
SU
LIST
CH SPD
08 SP
02 SP
10 SP
L1 LP
To cancel a Timer
Recording in progress...
Press POWER and then press
STOP within 10 seconds to
cancel the Timer Recording.
(The TIMER indicator goes out
on Multi Function Display.)
Press
to select number.
CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
3 To Replace program...
7 SUN 9:00A 12:00A 08
TODAY
CATEGORY : N/A
SELECT START DATE
SP
SELECT/
SET
1) Press
to display.
2) Repeat Step 3 (p.16)
to set new programs.
Timer
Recording
VCR Plus+
PROG.
LIST
DATE
START STOP
CH
:PLAY
:STOP
:REW
:FF
SET:
SELECT :
END
: PROG
PROG/
VCR+
or
ADD/DLT
To Clear program...
VCR Plus+
PROG.
DT START
STOP
-- -- : -- -- : -8 10 : 00P 12 : 00P
10
8 : 00P 9 : 00P
9 : 00P 10 : 00P
SU
LIST
CH SPD
-- -02 SP
10 SP
L1 LP
Press ADD/DLT.
CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
4
Press PROG/VCR+ button
to end the programming.
• If there are set programs, press POWER off
to set timer.
Important notes when using a DSS receiver
• When recording programs via a DSS receiver, the DSS receiver
must be left on.
• When recording programs via an antenna or cable, the DSS
receiver must be turned off.
17
V4622 P1-21 (2nd) [LSQT0509B].p65
17
2002/05/23, 18:28
Timer Recording Using VCR Plus+ System
Auto VCR Plus+ System Channel Setup (Part 1)
For [VCR-TV] or [VCR-cable box-TV] connection only.
VCR Plus+ System is ...
In order for VCR to read PlusCode numbers, some set
up is required. Guide channel numbers are assigned to
each local broadcast and cable station. Because this
number sometimes differs from the channel your TV
receives the station on, it is necessary to program the
VCR with local channel information. To receive VCR
Plus+ channels automatically, perform the steps below.
Or, see “Manual VCR Plus+ System Channel Setup”
section on page 20.
1
2
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
: ACT I ON
EXIT
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
Press ACTION*
to display menu.
a feature that allows you to set most
items of a timer recording by simply
entering a special code number
(PlusCode programming number)
found in TV GUIDE and selected
newspaper TV listings.
Important Note
• “Initial Setup” on pages 8 ~ 11
must be completed before “Auto
VCR Plus+ System Channel
Setup” can be done. If any part of
setup is incomplete, a warning
screen appears.
Press
to select CHANNEL.
SELECT/
SET
SELECT :
EXIT
: ACT I ON
3
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
:PLAY
:STOP
:REW
:FF
Press
to select VCR Plus+
CH SET UP and
press to display.
SELECT :
SET :
EXIT
: ACT I ON
4
VCR C / A CLOCK
AUTO SET
MANUAL
CHANNEL
ACTION
Press
to select AUTO SET
and
press to set.
SELECT :
SET :
EXIT
: ACT I ON
5
VCR C / A CLOCK
CHANNEL
PLEASE ENTER Z I P CODE
Z I P CODE : -----
SELECT :
SET :
: ACT I ON
EXIT
6
VCR C / A CLOCK CHANNEL
PLEASE SELECT HOW OFTEN
TO UPDATE
R I GHT NOW
EVERY NIGHT
EVERY MONDAY NIGHT
Press
to enter Zip Code and
enter each number.
Press or ACTION to
set.
Press
to select When to
Update and
press to set.
SELECT :
SET :
: ACT I ON
EXIT
7
VCR C / A CLOCK
CHANNEL
PLEASE LEAVE VCR OFF
Press ACTION to
return to normal screen.
• Make sure to leave VCR
off (overnight).
END
18
: ACT I ON
Notes
• When Auto Set is performed,
channels set in initial setup (pp. 8
~ 11) will be replaced by
automatically downloaded data.
• Make each entry within 1 minute or
VCR will leave this mode.
• Once local channels have been
programmed, they will stay in
memory, even in the case of a power
failure.
• If the start time for a timer recording
comes up during Auto VCR Plus+
System Setup, the timer recording
will have priority.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
18
2002/05/23, 18:28
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
System
Auto VCR Plus+ System Channel Setup (Part 2)
Before you perform the following steps, you
should have:
• completed “Auto VCR Plus+ System
Channel Setup (Part 1)” on page 18.
• left VCR off overnight, and turned it back on
after 9:00 AM the next day.
1
If channel updating was
successful...
VCR C / A CLOCK
SELECT/
SET
:PLAY
:STOP
:REW
:FF
If VCR could not
distinguish channel map...
CHANNEL
VCR C / A CLOCK
CHANNEL
VCR Plus+ CH SET
COMPLETED
PLEASE SELECT
VCR Plus+ CHANNEL
END
NEXT
ACTION
ADD/DLT
: ACT I ON
Press ACTION
to exit this mode.
3
VCR C / A CLOCK CHANNEL
SELECT VCR Plus+ CH
KABC CNN ESPN KNBC
12
13
14
15
51
42
18
33
1
5
10
7
101
99
110
78
SELECT :
: ADD / DLT
SET
: ACT I ON
EXIT
VCR C / A CLOCK
CHANNEL
PLEASE LEAVE VCR OFF
END
: ACT I ON
Press ACTION
to display SELECT
VCR Plus+ CH.
Continue with step 2.
Press
to
select channel map for
your area and press
ADD/DLT to set.
Press ACTION
to return to normal
screen.
• Make sure to leave
VCR off (overnight).
Channel map will be updated (overnight).
If it was successful, “VCR Plus+ CH SET
COMPLETED” appears on screen.
Press ACTION to exit.
Repeat these steps as necessary.
If Auto Setup fails, do “Manual VCR Plus+
System Channel Setup” on page 20.
To Change or Update Auto VCR
Plus+ System Channel Setup
Timer
Recording
2
: ACT I ON
(E.g. you selected wrong channel
map or zip code.)
a Do “Auto VCR Plus+ System
Channel Setup (Part 1)” steps
1~4 on page 18.
VCR C / A CLOCK
CHANNEL
UPDATE VCR Plus+ CH
SELECT VCR Plus+ CH
SELECT :
SET :
EXIT
: ACT I ON
b Press
to select UPDATE
VCR Plus+ CH or SELECT VCR
Plus+ CH, then press .
c If you selected UPDATE VCR
Plus+ CH, perform steps 5~7 in
the “Auto VCR Plus+ System
Channel Setup (Part 1)” section
on page 18.
If you selected SELECT VCR
Plus+ CH, perform steps 2~3 in
the “Auto VCR Plus+ System
Channel Setup (Part 2)” section
on this page.
19
V4622 P1-21 (2nd) [LSQT0509B].p65
19
2002/05/23, 18:28
Timer Recording Using VCR Plus+ System (continued)
Initial Setup.....
In order to use Timer Recording Using VCR Plus+ System, the Initial Setup on page 8 to 11 must
be completed for setting Clock and Channel.
Channel Setup.....
Since numbers assigned to channels found in TV Guide and selected newspapers may differ from
channels in your viewing area, you’ll need to enter your local TV channel number for each
corresponding Guide Channel.
If you perform the VCR Plus+ Channel set up procedures shown below, you will be able to perform
timer recordings using the PlusCode programming number listed in your local TV listing.
Manual VCR Plus+ Channel Setup
➛cable box➛
➛ TV] connection only.
For [VCR➛
➛ TV] or [VCR➛
1
To complete step 5 of setup,
do the following:
• Prepare a TV/Cable station line-up and
channels they are received on. Also, the
Guide channel numbers assigned to
your stations (found in TV Guide and
selected newspapers.)
• Make a 3-column chart (see sample).
Left column ➛ all stations you receive.
Middle column ➛ each station’s assigned
Guide channel number
from TV Guide, etc.
Right column ➛ channel number on
which your TV receives
the station.
2
HBO
Nickelodeon
CBS
FOX
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
Press ACTION*
to display menu.
Press
to select CHANNEL.
SELECT :
EXIT
: ACT I ON
3
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
Press
to select VCR Plus+ CH
SET UP, and press to
set.
SELECT :
SET :
EXIT
: ACT I ON
4
VCR C / A CLOCK
AUTO SET
MANUAL
CHANNEL
Press
to select MANUAL, and
press to set.
SELECT :
SET :
EXIT
: ACT I ON
SAMPLE ONLY
Broadcast or Cable Assigned Guide
channel No.
station name
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
: ACT I ON
EXIT
Channel No. on
which my TV
receives the station.
33
38
04
11
5
15
20
04
VCR C / A CLOCK
GUIDE CH
01
02
03
VCR C / A CLOCK
GUIDE CH
01
02
03
CHANNEL
RECEIVE CH
----
CHANNEL
RECEIVE CH
----
CLEAR : ADD/DLT
SELECT :
SET:
EXIT
: ACT I ON
To enter VCR Plus+
channels,
press to move cursor to
right, press
to enter
number, press to set,
and press
to scroll up/
down.
• Repeat step 5 until list is
complete.
To Make Corrections,
and to move to error, then
press
change, or ADD/DLT to erase number.
6
20
to
Press ACTION twice
to return to normal screen.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P1-21 (2nd) [LSQT0509B].p65
20
2002/05/23, 18:28
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
ontinued)
VCR Plus+ System Programming
SELECT/
SET
:PLAY
:STOP
:REW
:FF
Ready Checklist
Clock is set.
VCR Plus+ Setup is complete (see pp. 18 - 20).
1
VCR Plus+
PROG.
DATE
START STOP
LIST
CH
13 SAT --:-- --:-- -TODAY
CATEGORY : N/A
SLP
Press PROG/VCR+
button to display
PROGRAM.
PROG/
VCR+
NUMBER
keys
SELECT :
EXIT
: PROG
2
VCR Plus+
PROG.
LIST
ENTER PLUSCODE NUMBER
-
POWER
ADD/DLT
Press
to select display VCR
Plus+ screen.
ACTION
USING 0 - 9 KEYS
SELECT :
: PROG
EXIT
VCR Plus+
PROG.
LIST
ENTER PLUSCODE NUMBER
1
USING 0 - 9 KEYS
BACKSPACE :
END
: PROG
Press NUMBER keys
to enter PlusCode number
and press PROG/VCR+
button to set.
To Make Corrections,
press repeatedly
to delete number, then
repeat step 3.
• If the PlusCode number entered begins with “0,”
skip to step 5. Display in step 4 will not appear.
4
VCR Plus+
PROG.
LIST
ONCE
DAILY(MON-FRI)
WEEKLY
SELECT :
END
: PROG
5
VCR Plus+
PROG.
LIST
DATE
START
CH
STOP
13 SAT 2:20P 3:20P 02
ABC
TODAY
SLP
CATEGORY : N/A
SELECT RECORD SPEED
SELECT :
SET:
END
: PROG
6
VCR Plus+
PROG.
DT START
STOP
13 2 : 00 P 3 : 20P
-- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
LIST
CH SPD
02 SLP
-- --- --- --
CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
7
Press
to select ONCE,
DAILY(MON~FRI), or
WEEKLY record
frequency and press
PROG/VCR+ button to set.
Press
to select category and
recording speed.
Press to set.
Press PROG/VCR+
button to end program.
Press PROG/VCR+
button again to exit.
• Press ADD/DLT
to delete the program.
Press POWER off to set the timer.
(“TIMER” lights up on Multi Function Display.)
V4622 P1-21 (2nd) [LSQT0509B].p65
21
Timer
Recording
3
Do normal Timer Record if...
• PlusCode number is not listed for
program.
• the program (e.g. sports event) may
run over set stop time.
See page 17 to:
• cancel a timer recording in progress.
• review, replace, or clear program
contents.
Important for DSS/Cable Box Users
• When recording via DSS, the receiver
must be left on. When recording via
cable or antenna, DSS receiver must
be off.
• When recording via a cable box,
leave box on and tuned to channel to
be recorded.
Notes
• Do not overlap program times.
• PlusCode numbers cannot be used to
program VCR to record DSS and
cable box channels.
• Make each entry within 1 minute or
the VCR will exit setup mode.
• Once VCR Plus+ channel setup is
done, channels stay in memory. If a
power interruption occurs, VCR Plus+
channel setup may be lost. Please do
VCR Plus+ channel setup again.
• Obtain unlisted PlusCode numbers by
calling 1 - 900 - 454 - 7587. Call costs
about $.95 per minute.
21
2002/05/23, 18:28
Multi-Brand Control Feature
Multi-Brand Control Setup
The Remote Control can be set to control some TV and
Cable box/DSS functions.
1
2
POWER
Find your TV and Cable Box/DSS Receiver Brand
Code Number on the following page.
TV
DSS/
CABLE
Setup for TV control,
➛ hold down TV button,
➛ enter code with NUMBER keys.
Setup for Cable or DSS control,
➛ hold down DSS/CABLE button,
➛ enter code with NUMBER keys.
• If code number is 100 or greater,
➛ press 100 key, then other digits.
E.g., press 100 - 0 - 2 for 102.
3
NUMBER
keys
Confirm code entry,
➛ press POWER to turn selected unit on or off.
• See table below for controllable functions in each mode.
ENTER
• Repeat setup after remote battery replacement.
• Remote will not control every TV, cable box, or
DSS made by the manufacturer listed. If you get
no response, your particular unit cannot be
controlled. There are NO additional codes for the
products listed. If your product is not listed, then
the remote is not compatible with that product.
Notes
Using Multi-Brand Control
After remote is set up, you can select VCR, TV, or DSS/
CABLE for the desired function.
Press VCR, or TV, or DSS/CABLE on the remote.
(Table below shows available unit buttons for each mode.)
Mode
Unit
VCR
CABLE/
DSS
22
TV
All
TV
Notes
VCR
CABLE/ DSS
VOL UP/DOWN
VCR/TV, PLAY,
STOP EJECT,
SAP/ Hi-Fi,
DISPLAY, FF,
REW, PAUSE/
SLOW, REC,
SPEED, CA/ZERO,
COUNTER
RESET, TAPE
POSITION
POWER, INPUT,
number keys,
ENTER, CH
UP/ DOWN,
VOL UP/DOWN
VOL UP/ DOWN POWER, ENTER,
number keys
(except 100key),
CH UP/ DOWN
• Not all functions listed may be controllable.
• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing
NUMBER keys for channel selection.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
22
2002/05/23, 18:29
TV Brand Code Numbers
Panasonic ........................ 01, 02
Quasar ............................. 01, 02
RCA ....................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox .............................. 05
Sylvania ................................. 05
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba .................................. 09
Sanyo .................................... 10
Fisher .................................... 10
JVC ........................................ 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star ................... 15, 16, 17
Cable Box Brand Code Numbers
Oak Sigma ..................................... 46, 11, 129, 101
Panasonic .................................. 17, 16, 08, 87, 109
Philips ................... 23, 24, 20, 13, 07, 50, 128, 129
Pioneer ...................................................... 06, 05, 12
Pulsar .................... 04, 42, 63, 44, 30, 52, 124, 126
Quest ........................................................ 06, 05, 12
Radio Shack ............................... 44, 51, 75, 59, 126
RCA ............................................ 17, 16, 08, 87, 109
Realistic ..................................... 44, 51, 75, 59, 126
Recoton ...................................... 44, 51, 75, 59, 126
Regal ................. 41, 14, 15, 28, 102, 104, 103, 130
Regency .................................................. 28, 29, 130
Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ...................................... 42, 06, 32, 05, 40
Scientific Atlanta ................... 08, 09, 25, 61, 53, 87
Sheritech ............................................................... 27
Signal ............................................................ 26, 112
SL Marx ............. 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ...................................... 17, 16, 08, 87, 109
Standard Components ............... 32, 39, 42, 44, 126
Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06
124, 126
Sylvania .......................................................... 19, 18
Teknika ........................................................... 74, 35
Telecaption .................................................... 77, 127
Teleview ................................. 40, 19, 38, 32, 42, 06
Texscan .......................................................... 19, 18
Tocom ................................... 34, 33, 01, 42, 66, 120
Toshiba ................................................................. 36
Unika ........................... 44, 42, 63, 29, 01, 126, 120
Universal .............................. 52, 43, 44, 63, 42, 126
Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107
Videoway .......................................... 07, 23, 50, 129
Vidtek .................................................................... 64
Zenith ............................................... 07, 23, 50, 129
Advanced
Operation
Archer ......................... 44, 06, 01, 120, 05, 63, 126
Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30
52, 04, 124, 126
Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126
Curtis ..................................... 08, 09, 25, 61, 53, 87
Century ...................................... 44, 51, 75, 59, 126
Cabletenna .................. 29, 09, 01, 63, 120, 44, 126
Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126
Diamond ...................... 29, 09, 01, 63, 120, 44, 126
Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107
Eastern ................................................... 28, 29, 130
Explorer .................................. 08, 09, 25, 61, 53, 87
Gemini ..................................................... 30, 04, 124
General Electric ...................................... 01, 57, 120
General Instruments . 01, 84, 83, 34, 03, 02, 04, 55
65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Gerrard ............................................... 44, 51, 75, 59
GC Electronics ............... 44, 42, 63, 29, 30, 52, 04
124, 126
Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130
Hitachi ................................................................... 31
Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ...................................................... 30, 04, 124
Macom ................................................................... 31
Magnavox ...................................................... 26, 112
Matsushita ................................. 17, 16, 08, 87, 109
Movietime ...................... 32, 39, 42, 44, 126, 38, 40
Maestro ........................................................... 74, 35
NEC .................................................... 40, 19, 38, 32
NSC .................................................... 40, 19, 38, 32
Novavision ............................. 08, 09, 25, 61, 53, 87
Next Level ........... 01, 84, 83, 34, 03, 02, 04, 55, 65
66, 67, 68, 120, 106, 121, 122
Oak ................................................. 46, 11, 129, 101
DSS Brand Code Numbers
Toshiba .................................................................. 90
Hitachi/ Hughes ............................................... 91, 99
Primestar ............................................................... 92
Drake ..................................................................... 93
Magnavox ........................................................ 94, 95
Uniden ............................................................. 94, 95
Optimus ........................................................... 94, 95
Panasonic .............................................................. 96
ProScan ................................................................. 97
RCA ....................................................................... 97
SONY ............................................................ 98, 105
Important Notes
• Due to changes in infra-red commands used by manufacturers, some brands have several
codes. If your unit does not respond to the first code, please try the next one.
• Some TV, Cable Box and DSS Box brands require you to turn on the power manually.
V4622 P22-44 (2nd) [LSQT0509B].p65
23
2002/05/23, 18:29
23
Advanced Connections
Audio/Video Connection
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR to
them to receive higher quality picture and sound.
IN FROM ANT.
VCR
AUDIO OUT
TV
AUDIO IN
R
R
L
OUT TO TV
R
L
VHF/UHF
VIDEO OUT
VIDEO IN
1
2
3
Connect the VIDEO OUT terminal on the VCR to the VIDEO IN terminal
of your TV.
Connect the “L” and “R” AUDIO OUT terminals on the VCR to the “L” and “R”
AUDIO IN terminals of your TV.
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to “VIDEO.”
■ With a Cable Box (VCR
ANT
or
CATV
Cable Box)
TV
IN FROM ANT.
AUDIO
R
VIDEO
IN 1
CABLE BOX
L VHF/UHF
IN OUT
OUT TO TV
■ Connect With Two Cable Boxes
VCR
CABLE BOX
IN FROM ANT.
AUDIO
R
IN OUT
VIDEO
IN 1
24
L VHF/UHF
OUT TO TV
OUT
2-Way Splitter CABLE BOX
OUT 1 OUT 2
IN OUT
R
AUDIO
L
VIDEO
VHF/UHF
OUT
VCR
ANT
or
CATV
You Can
IN OUT
A/B Switch
IN 1
IN 2
• view any
(including
scrambled)
channel.
You Cannot
• record
scrambled
channels.
• use VCR Remote
Control to select
channels without
using Multi-brand
control feature.
You Can
You Cannot
• record and view
• view channel
both scrambled
other than the
and unscrambled
one selected
channels if
for any type of
additional
recording.
equipment is
TV added.
• do a Timer
recording of a
This connection
IN OUT
requires: two
channel unless
R
AUDIO
converter boxes,
you select it at
L
an A/B switch,
the cable box.
VIDEO
and a 2-way
VHF/UHF
splitter.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
24
2002/05/23, 18:29
MTS Broadcast/ VHS Hi-Fi Stereo System
TV
Connection
Make the Audio/Video Connection as shown on the
previous page.
• You can use a TV connected to a Stereo amplifier and
speakers instead of a Stereo TV.
VCR
R
L
Stereo Amplifier
AUDIO OUT
R
R
L
VHF/UHF
R
AUDIO IN
L
OUT TO TV
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen
displays. The signal being received is indicated with an “ ” mark
while the selected audio mode is indicated with an arrow.
To display the broadcast signal being received,
➛ press DISPLAY.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main
language) and Secondary Audio Program
(sub language) broadcasts are being
received simultaneously. Select STEREO or
SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo
broadcast. Select STEREO audio mode.
• If stereo broadcast is weak and display
flickers, select MONO audio mode for
possibly better results.
STOP
1 2 : 0 0AM
ABC
0 : 00 : 00
SP
1 2 : 0 0AM
ABC
0 : 00 : 00
SP
STEREO
SAP
MONO
STOP
STEREO
SAP
MONO
STOP
1 2 : 0 0AM
STEREO
SAP
MONO
MONO broadcast
STOP
STEREO
SAP
MONO
®
1 2 : 0 0AM
ABC
0 : 00 : 00
SP
Normal monaural sound broadcast.
1
2
Press SAP/ Hi-Fi
to display audio mode.
(Display disappears after 5 seconds.)
STEREO
SAP
MONO
Press SAP/ Hi-Fi
repeatedly to select
desired mode.
• Refer to “Receivable
Broadcast Types” above.
-TV Noise
Equipped with
Reduction for true MTS
®
reproduction.
-TV Noise
Reduction is required for good
stereo separation and audio
®
fidelity.
is a registered
trademark, and is licensed by
®
Technology Licensing.
Audio Mode for Playback
1
2
3
Start playback.
See page 14.
Press SAP/ Hi-Fi
to display audio mode.
(Display disappears after 5 seconds.)
Press SAP/ Hi-Fi
repeatedly to
select desired
mode.
H I F I : L/R
HIFI : L
HIFI : R
NORMAL
• Arrow indicates
selection.
3
Do a recording.
See page 15.
• Arrow indicates
selection.
Notes
• Select “HIFI(L/R)” or
“HIFI(L)” or “HIFI(R)”
to listen to stereo
recordings in stereo
sound. Select
“NORMAL” for
monaural sound.
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo
tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a
stereo TV or an external stereo amplifier and speakers. (See top of this page.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
V4622 P22-44 (2nd) [LSQT0509B].p65
25
Advanced
Operation
Audio Mode for Recording
SAP/Hi-Fi
ABC
0 : 00 : 00
SP
SAP broadcast
Secondary Audio Program (sub language)
broadcast. Select SAP audio mode for the
sub language.
DISPLAY
2002/05/23, 18:29
25
Tape Operation
Ready Checklist
detects and marks the beginning and
end points of commercials on your tape for recordings over 15
minutes in length. When
marked tape
is played back, the VCR a automatically advances through the
commercial segments at high speed. You can also set this feature
to Manual so as to have more control over the advance process.
The effectiveness of this system can vary due to differences in
the way television stations broadcast. See page 28 for answers
to the most commonly asked questions about this feature.
All connections are made.
One time Setup completed.
VCR is plugged in.
TV is turned on and set to CH3, 4
or Video on TV.
SELECT/
SET
:PLAY
:STOP
:FF
:REW
Marking
When C/A RECORD: ON, VCR automatically rewinds the
tape after a recording has been made and marks the
beginning and end of any detected commercial blocks.
After marking is done, the tape is returned to the end of
the recording. Commercials are not erased from the tape.
1
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
: ACT I ON
EXIT
2
VCR
C/A
CLOCK
CH
SET UP COMMERCIAL ADV.
C/A RECORD
:ON
C/A PLAYBACK
:AUTO
NUMBER
keys
Press ACTION*
to display menu.
ACTION
Press
to select C/A and display
SET UP COMMERCIAL
ADV.
SELECT :
EXIT
: ACT I ON
3
VCR
C/A
CLOCK
CH
SET UP COMMERCIAL ADV.
C/A RECORD
:ON
C/A PLAYBACK
:AUTO
Press
to select C/A RECORD
and press to set.
SELECT :
SET :
: ACT I ON
EXIT
Note
• When using the timer to record two
adjacent shows on the same
channel, better accuracy can be
obtained by programming each
show separately.
ON
Timer Recording, VCR Plus+ System, and One Touch recordings are marked automatically.
When STOP is pressed during normal recording, Select One of a)
THE VCR IS WAITING TO
or b) or c).
MARK COMMERCIALS IN THE
PROGRAM YOU RECORDED.
a) Press 1 key to mark the recording now.
“NOW MARKING COMMERCIALS” appears.
b) Press 2 key to mark the recording later (after the power has
MARKING
been turned off).
NOW
: PRESS 1
LATER
: PRESS 2
• If the tape is rewound and another recording started before the
CANCEL : PRESS ACTION
power is turned off, commercials may not be marked correctly.
c) Press ACTION to cancel the marking of this recording.
OFF The VCR will not mark commercials.
When you are editing or dubbing a tape, or when you do not wish to use this feature,
OFF should be selected.
4
Press ACTION again
to return to normal screen.
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
26
2002/05/23, 18:29
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Playback
PLAY
When playing back a recording which has been
feature, you
marked using the
can either set VCR to automatically advance through
marked commercial blocks, or set it so that
commercials are only skipped on your command.
1
2
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
: ACT I ON
EXIT
VCR
C/A
CLOCK
CH
SET UP COMMERCIAL ADV.
C/A RECORD
:ON
C/A PLAYBACK
:AUTO
FF
Press ACTION
to display menu.
SELECT/
SET
:PLAY
:STOP
:FF
:REW
Press
to select C/A and
display SET UP
COMMERCIAL ADV.
SELECT :
EXIT
: ACT I ON
3
VCR
C/A
CLOCK
CH
SET UP COMMERCIAL ADV.
C/A RECORD
:ON
C/A PLAYBACK
:AUTO
ACTION
Press
to select C/A PLAYBACK
and press to set
“AUTO” or “MANUAL”.
CA/ZERO
SET :
SELECT :
: ACT I ON
EXIT
AUTO
MANUAL : VCR will advance through commercials only
when CA/ZERO is pressed. Playback will
resume when the end mark of a commercial
block is found, or a new recording or blank
portion is detected, or after 8 minutes.
4
Press ACTION again
to return to normal screen.
and
are
registered trademarks of SRT, Inc.
A Jerry lggulden invention licensed
in association with Arthur
D. Little Enterprises, Inc.
U.S.Pat. No. 5,333,091;
5,692,093; 5,696,866
other patents pending
Advanced
Operation
: VCR will automatically advance through
marked commercial blocks recorded on the
tape and then resume playback.
Notes
• The selection mode in step 3 remains set unless there is a power outage in which case the
original factory setting will be restored.
• If playback is started in the middle of a commercial, only a single commercial is shown, or an
individual commercial is longer than 1 minute, the commercial may not be skipped.
Press FF to quickly advance through the commercial.
• Part of a recorded program may be skipped over if the program portion between commercials
is less than 1 minute or there are frequent dark and quiet scenes during the program. To view
the portion of tape being incorrectly skipped, press PLAY while the VCR is skipping, reverse
the tape to a point just prior to where the skipping began and press PLAY again. This time the
group will not be automatically skipped. Automatic skipping will be re-enabled when the end of
the marked group is detected.
27
V4622 P22-44 (2nd) [LSQT0509B].p65
27
2002/05/23, 18:29
Tape Operation (continued)
The most commonly asked questions about
are answered below.
Question
Answer
How fast does the VCR advance
through commercials?
The VCR advances through a 3-minute commercial
block in about 8 to 12 seconds if the tape speed is
SLP. In SP, it takes about 25 to 35 seconds.
Are commercials advanced through only
when I playback a recording?
Yes. The commercials are not marked until after the
recording is finished.
Are commercials still recorded on the
tape in case I choose to view them
sometime?
Yes. By setting the C/A PLAYBACK to MANUAL (see
page 27), you can view or advance through
commercials as desired.
Does
all recording speeds?
Yes.
SLP.
work in
works in SP, LP, and
Does the VCR advance through
commercials each time I playback tapes
which were recorded using
?
Yes. As long as C/A PLAYBACK is set to AUTO (see
page 27), the VCR should advance through
commercials each time the tape is played back.
After marking commercials, does the
VCR stop at the end of the tape, or
rewind to the beginning?
The tape stops at the end of the recording so that
any additional timer recordings can be performed.
Can I play my
recordings in non-
marked recordings will
Yes.
play in nonVCRs, but
commercials will not be advanced through.
VCRs?
Does the marking process interfere with
other programmed recordings?
No. If the interval between 2 or more timer programs
is not sufficient to mark the recording, marking will be
done after all recordings are complete and the power
goes off.
What happens if I cancel the marking in
progress so I can use the VCR?
Marking will be resumed when the VCR's power is
turned off as long as the tape has not been ejected.
What if part of my program is advanced
through along with the commercials?
Please see the 3rd note on page 27.
Additional Notes:
• Because of the various ways in which commercials are broadcast, the VCR may not be able
to recognize all commercials.
• If a timer recording is scheduled for the middle of the night, please be aware that the VCR will
make some noise as it rewinds and fast forwards the tape while marking commercials.
and
are registered trademarks of SRT, Inc.
A Jerry lggulden invention licensed in association with Arthur D. Little Enterprises, Inc.
U.S.Pat. No. 5,333,091;
5,692,093; 5,696,866
other patents pending
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
28
2002/05/23, 18:29
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Ready Checklist
helps you locate certain
parts of prerecorded movies (rented or
purchased). The feature works in two ways.
• You can go to the beginning of the movie.
• You can skip from one preview to the next.
works only on tapes
recorded in SP speed with the record tab
removed.
1
2
All connections are made.
One time Setup completed.
VCR is plugged in.
TV is turned on and set to CH3, 4
or Video on TV.
PLAY
SELECT/
SET
Insert a tape
without record tab.
INDEX
SEARCH
PROG. END
MOVIE
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
:PLAY
:STOP
:FF
Press SEARCH/
M/A SKIP* to
display SEARCH.
STOP
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT :SEARCH M/A SK I P
EXIT :STOP
SEARCH/
M/A SKIP
• If you inserted a cassette with the record tab
or if you selected “INDEX SEARCH” go to
page 30.
3
INDEX
SEARCH
PROG. END
SEARCH
PROG. END
MOVIE
MOVIE
SEARCHING FOR START
OF MOVIE
Press FF
to start searching.
• To cancel,
press STOP.
CANCEL : STOP
To Search for Preview.
You can override the operation of
SEARCH FOR
PREVIEWS mode by pressing SEARCH/ M/A
SKIP during tape searching.
works by searching
the tape past each preview and then reversing
back to the start of the detected preview.
While the tape is reversing back, if SEARCH/ M/
A SKIP is pressed,
will
begin searching for the next preview.
While searching for the next preview, if you see
the start of a preview which you wish to watch,
press SEARCH/ M/A SKIP and
will immediately
reverse back to the start of that preview,
instead of searching further past the preview
start point. Once the VCR is playing a preview,
press SEARCH/ M/A SKIP to advance to the
next preview, long commercial or the start of
the movie (whichever is next).
1
When the movie is found...
5
INDEX
SEARCH
PROG. END
MOVIE
Press PLAY
to start playback.
THE MOV I E I S READY
START : PLAY
• To cancel,
press STOP.
CANCEL : STOP
Advanced
Operation
4
Press SEARCH/ M/
A SKIP twice to
GO TO START MOVIE
select MOVIE and
GO TO PREVIEW
press
to select
SEARCH START : FF
SELECT
:
GO TO START
EXIT : SEARCH M/A SK I P
MOVIE or GO TO
PREVIEW.
Select “GO TO START MOVIE,” if you want
to advance directly to beginning of the
movie.
➛ continue with step 4.
Select “GO TO PREVIEW,” if you want to
view the first (next) preview.
➛ see “To Search for Preview” at right.
INDEX
Start preview searching.
1) In step 3 at left, select GO
TO PREVIEW.
2) Press FF.
• If you want to playback, press PLAY.
When a preview is detected, VCR
will start playback.
Start next preview searching.
Press SEARCH/ M/A SKIP.
2
• To cancel, press STOP.
29
V4622 P22-44 (2nd) [LSQT0509B].p65
29
2002/05/23, 18:29
Tape Operation (continued)
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.
Program End Search
Index Search
1
INDEX
SEARCH
PROG. END
MOVIE
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT :SEARCH M/A SK I P
EXIT :STOP
Press SEARCH/
M/A SKIP* to
display SEARCH
in Stop or Play
mode, and then
press NUMBER
keys to select
recording number.
Locates end point of recording for continuity.
1
2
Press SEARCH/ M/A SKIP twice to
display SEARCH in Stop or Play mode.
• To calculate
number, see below.
Press FF or REW
on the remote to
start search.
FORWARD SEARCH : FF
REVERSE SEARCH : REW
SEARCH START :FF
NEXT
EXIT
Examples of Program End Search.
Fig. 1
Program 1
the current tape position
Press SEARCH button
Program 2 or BLANK
End Point
FF
Fig. 2
INDEX
INDEX
Program 1
BLANK
Program 2
FF
INDEX
Program 1
End Point
2
3
4
5
6
BLANK
To go to rec. 6 from rec. 2, enter 4 and press FF.
NOTE:
2
3
4
5
6
Upon locating end point,
➛ search continues 7 sec. past end point,
➛ tape rewinds to 10 sec. before end point,
➛ tape plays to end point and stops.
7
indicates start points of each recording.
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
30
FF
Program 2
If search exceeds
a few seconds in
BLANK area.
7
Example 2:
1
End Point
the current tape position
Press SEARCH button
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
BLANK
the current tape position
Press SEARCH button
Fig. 3
Example 1:
• To cancel, press
PLAY or STOP.
:SEARCH M/A SK I P
:STOP
• To cancel, press
PLAY or STOP.
To Calculate Index Number
Press FF on the
remote to start
PROGRAM END
SEARCH.
MOVIE
INDEX
2
Play begins at end
of search.
To search forward
or back 1 index,
press FF or REW
on the remote or
VCR while screen
left is displayed (10
sec.).
INDEX SEARCH
SEARCH
PROG. END
INDEX
Note
• If Program End Search is started very
close to an index mark, that mark may be
skipped over.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
30
2002/05/23, 18:29
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Zero Search
To quickly return to a specified tape location.
SELECT/
SET
PLAY
:PLAY
:STOP
:FF
REW
FF
ACTION
1
2
Press DISPLAY during play
to display Counter.
PLAY
1 2 : 0 0AM
0 : 00 : 00
SP
NUMBER
keys
STOP
COUNTER
RESET
DISPLAY
SEARCH
M/A SKIP
CA/ZERO
3
4
5
Press COUNTER
RESET at desired
position to reset to
“0:00:00”.
Continue to record, playback etc.
Press STOP.
REW
STOP
1 2 : 3 0AM
1 2 : 3 1AM
CH 02
0 : 30 : 30
SP
CH 02
0 : 00 : 00
SP
Press CA/ZERO
in Stop mode
to start ZERO
SEARCH.
• Unit will go into FF
or REW mode and
stop at the last
point the Counter
was set to 0:00:00.
Advanced
Operation
Repeat Play
Set to playback a recording over and over.
1
2
3
Auto Operation Functions
Press ACTION
to display menu.
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:ON
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
: ACT I ON
EXIT
Press
to select REPEAT
PLAY and press
to set ON or OFF.
ON: Play repeats at
tape end or if
unrecorded
portion over 30
sec. is detected.
Press ACTION
to return to normal screen.
Auto Play
Insert a tape ➛ Power comes on,
➛ Play starts if there is no record tab
(see p. 4).
Auto Rewind
Play
➛ Tape end, ➛ Rewind
Fast Forward
Play Auto Eject
(Repeat Play must be off)
Play, ➛ Tape end, ➛ Rewind,
➛ Tape ejects if there is no record tab
31
V4622 P22-44 (2nd) [LSQT0509B].p65
31
2002/05/23, 18:29
Special VCR Features
Channel Caption
When set, station name, e.g. ABC, CBS, and channel number appear on-screen.
Set up to 24 preset captions, and/or 10 manually created captions.
You need a list of stations and the channel numbers you receive them on.
Preset Caption
1
2
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
EXIT
: ACT I ON
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
Manual Caption
Press ACTION*
to display menu.
2
Press
to select
CHANNEL.
SELECT :
: ACT I ON
EXIT
3
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
SELECT :
SET :
: ACT I ON
EXIT
4
VCR C / A CLOCK CHANNEL
PRESET CAPTION
MANUAL CAPTION
SELECT :
SET :
: ACT I ON
EXIT
5
VCR C / A CLOCK CHANNEL
ABC
-CBS
-FOX
-NBC
-A&E
-FAM
-CLEAR : ADD/DLT
SELECT :
SET :
EXIT
: ACT I ON
• Repeat step 5 until
the list is complete.
Press
to select
CHANNEL
CAPTION and
press to set.
Press
to select PRESET
CAPTION and
press to set.
32
Do “Preset Caption” steps 1~3 on
left.
VCR C / A CLOCK CHANNEL
PRESET CAPTION
MANUAL CAPTION
Press
to select MANUAL
CAPTION and
press to set.
SELECT :
SET :
: ACT I ON
EXIT
3
VCR C / A CLOCK
CH NUMBER
CHANNEL
CAPTION
02
----
CLEAR : ADD/DLT
SELECT :
SET :
: ACT I ON
EXIT
Press
to
select CH
NUMBER
and press to
move cursor to
the right.
• Channels already set and channels deleted
from Channel Memory are not displayed.
• You can set a total of ten channel captions.
4
• To create your
own captions, go to
“Manual Caption”
on right.
VCR C / A CLOCK
CH NUMBER
CHANNEL
CAPTION
02
----
CLEAR : ADD/DLT
SELECT :
SET :
: ACT I ON
EXIT
Assign preset
captions.
A
1) Press
to
highlight caption.
2) Press to move
cursor to the right.
3) Press
to
select CH
number.
4) Press to set.
To make corrections,
Press
and
to select the channel number,
then press
to change, or ADD/DLT to
delete the number.
6
1
B
C
9
Press
to enter CAPTION
and press to
set.
• Characters
change in
following order.
Z BLANK
2 1 0 /
&
!
• Repeat steps 3 and 4 as desired.
To make corrections,
to move to the incorrect entry,
Press
then press
to make correction.
Or, press ADD/DLT to clear the caption.
5
Press ACTION twice
to return to normal screen.
Press ACTION twice
to return to normal screen.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
32
2002/05/23, 18:29
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Remote Warning ON/OFF Feature
If Multi-brand feature is used (p. 22), and this
feature is set to on, a warning appears whenever
an invalid key is pressed in TV, DSS, or Cable
mode.
SELECT/
SET
:PLAY
:STOP
:REW
:FF
1
2
ACTION
Press ACTION
to display menu.
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:ON
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
EXIT
: ACT I ON
Press
to select REMOTE
WARNING and
press to set ON
or OFF.
• If “OFF,” remote warning will not appear if
invalid key is pressed.
ADD/ DLT
3
Press ACTION
to return to normal screen.
VCR Lock Feature
When set to ON, all operations except for timer
record and tape eject are prohibited. Useful for
households with small children.
VCR LOCK ACT I VATED
To turn off,
repeat above.
Advanced
Operation
To turn on,
hold down REC on
the VCR in Stop mode
with no tape inserted
for 7 sec.
(Please ignore the NO
CASSETTE warning.)
VCR LOCK OFF
• VCR Lock cancels in 24 hours if clock is set.
REC
33
V4622 P22-44 (2nd) [LSQT0509B].p65
33
2002/05/23, 18:29
Special VCR Features (continued)
Time Stamp Feature
Ready Checklist
The VCR writes program data (see example below)
about the first 10 seconds of every recording.
The information is then displayed the first 10 seconds of
playback.
1
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
EXIT
: ACT I ON
2
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:ON
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
EXIT
: ACT I ON
3
Clock is set to correct time.
Record tab in place. (See p. 4.)
Press ACTION*
to display menu.
VCR/TV
SELECT/
SET
:PLAY
:STOP
:REW
:FF
Press
to select TIME STAMP
and press to set.
• When “OFF” is selected,
the program data is
written on the tape, but
will not be displayed.
ACTION
TAPE
POSITION
Press ACTION again
to return to normal screen.
<Time Stamp Example>
One Touch
Recording
Timer Recording
11 / 11 / 2001 SUN
12 : 0 0PM
CH 0 8 ABC
11 / 11 / 2001
12 : 0 0PM CH 0 8 ABC
When Clock is not
set...
SHUTTLE
Ring
SUN
1 : 0 0PM
MOVIE
Tape Position and Tape Status Feature
To find out the present tape position and amount of tape remaining.
Tape position is displayed for VHS-C type Cassettes, tapes
under 30 minute long, and some other tapes, but the
position is not correct.
1
Press TAPE POSITION
to detect current tape position.
DETECTING TAPE POSITION
SP
R 120 M I N.
BEG I N
2
34
• “DETECTING TAPE POSITION” is displayed
only when a cassette is first inserted, and it
takes several seconds for correct tape
position to appear.
• The present tape position indication and
amount of tape remaining (according to
tape speed) is displayed.
• Tape remaining time display may not be
precise.
END
Press TAPE POSITION
to return to normal screen.
Note
This function cannot display
exact amount of tape
remaining for tapes 30
minutes or less, or for tapes
over 120 minutes in length.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
34
2002/05/23, 18:29
*Important: If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Auto Shut-Off Feature
Weak Signal Display ON/OFF Feature
The power shuts off at a preset time.
1
2
3
When set to “ON,” picture is displayed
regardless of signal strength.
Press ACTION
to display menu.
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:ON
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
EXIT
: ACT I ON
Press
to select AUTO
SHUT-OFF.
Press repeatedly
to change shutoff
time as shown
below.
1
2
Press ACTION
to return to normal screen.
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
: ACT I ON
EXIT
VCR C / A CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPTION
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
SELECT :
SET :
: ACT I ON
EXIT
2 Hours
OFF
4 Hours
6 Hours
Note
The shut-off countdown will not function
during Play or Record.
VCR/TV Selector Feature
The VCR VCR/TV selection can be set to
auto or manual.
1
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:ON
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
EXIT
: ACT I ON
Press ACTION
to display menu.
• ON: Picture is displayed despite signal
condition and may be of poor quality.
OFF: Screen turns solid blue when signal is
weak or non-existent.
• Selecting ON has no effect on connected
equipment with blue back feature.
3
Press ACTION
to return to normal screen.
Shuttle Variable Speed Search
The SHUTTLE Ring allows you to smoothly
control the tape speed during special effects
playback in both forward or reverse.
Press
to select AUTO
VCR/TV.
Press to set
ON or OFF.
• OFF(Manual): You select “VCR” or “TV”
mode using the VCR/TV
button on the unit or remote.
• ON(Auto):
“VCR” mode is automatically
set when VCR is turned on,
or in Play mode.
3
Press
to select and
display CHANNEL.
Press
to select
WEAK SIGNAL
DISPLAY, and
press to set ON
or OFF.
Press ACTION
to return to normal screen.
Note
For more on VCR/TV selection, see “Record
one station, watch another” and “Select
channels at VCR” sections (p.15).
Begin the forward or reverse search.
Turn SHUTTLE Ring while in Play or Still mode.
• The more you turn the Ring, the faster the
search speed will be.
Release the Shuttle mode.
Advanced
Operation
2
VCR
C / A CLOCK
CH
REPEAT PLAY
:OFF
T I ME STAMP
:ON
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
AUTO VCR/TV
:ON
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
EXIT
: ACT I ON
Press ACTION
to display menu.
Press a function button such as : PLAY,
STOP, etc.
• The VCR performs the function of the button
pressed.
Notes
• When the SHUTTLE Ring is turned more
than half in Stop mode, normal Fast Forward
or Rewind will begin.
• Some noise bars are normal during Shuttle
operation.
• After 3 minutes in Still or Slow, the VCR will
go into Stop mode.
• When the SHUTTLE Ring is released, the
VCR goes into Still mode.
35
V4622 P22-44 (2nd) [LSQT0509B].p65
35
2002/05/23, 18:29
Copying Your Tapes (Dubbing)
Connection
(Rear Connection shown.)
IN FROM ANT.
VCR
R
R
L
Front of VCR
TV
VCR
AUDIO OUT
VIDEO IN 2
OUT TO TV
AUDIO IN
L-AUDIO IN2-R
R
L
(Audio/Video In Terminals on
the front of VCR are available)
R
L
VIDEO OUT
VIDEO IN
VHF/UHF
1
Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on Recording VCR. To
monitor the dubbing, also connect a TV as shown.
2
Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN
terminals on Recording VCR.
In place of a Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit’s Audio/Video outputs to the Recording VCR.
Playing (Source) VCR
1
2
Insert pre-recorded tape.
Recording (Editing) VCR
Insert blank tape with record tab.
Press INPUT to set VCR Input mode to LINE1
for Video Input (Rear) or to LINE2 for Video Input
(Front). (See “Selecting the Input Mode” below.)
Press PLAY, then PAUSE/SLOW
Press REC, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode. immediately to enter REC/PAUSE mode.
The operation of steps 4 and 5 must be done on the
playing and recording VCRs at the same time.
Press PLAY to start dubbing.
Press PAUSE/SLOW to start dubbing.
Playing VCR starts playback.
Recording VCR starts recording.
3
4
5
Press STOP to stop dubbing.
Press STOP to stop dubbing.
To Monitor Dubbing on Your TV
Selecting the Input Mode
1
Turn your TV on and tune to the Recording
VCR channel (CH3 or CH4).
2
Set the VCR/ TV Selector on the Recording
VCR to “VCR.”
Method 1: Press INPUT repeatedly.
Channel Number ↔ LINE1 ↔ LINE2
Method 2: Press CH
/ .
Display will change as below.
1
LINE2
Note
Dubbing tapes protected with Copy
Guard will result in poor quality
recordings.
2
LINE1
3
(CABLE) (TV)
125 or 69
• “L1” or “L2” lights on Multi-Function Display
(about 4 sec.) when LINE1 or LINE2 is selected.
• LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.
Caution: Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement.
36
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
36
2002/05/23, 18:29
VCR & Cassette Information
Specifications
Video Head Clog Sensor
During playback, this
screen appears if
clogging is detected.
To remove screen,
press PLAY on the
remote or VCR.
V I DEO HEADS MAY
NEED CLEAN I NG
PLEASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END
: PLAY
Cleaning Tape
• Use “dry” type head cleaning
cassette only. (Part No. NV-TCL30PT
is recommended.)
• Follow cleaning tape instructions
carefully. Excessive use of tape can
shorten head life.
• If head clog symptoms persist, contact
your nearest Factory Servicenter or
authorized Servicenter. (See page 41.)
Cleaning the VCR
Use a soft cloth or dusting attachment
of a vacuum cleaner to remove dust
from the ventilation holes on the back
sides and bottom of the cabinet.
Features for a Quality Picture
Digital Auto Picture
Automatically controls the video output signal for
less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture
noise)
Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING) / on the remote
control or VCR until the picture clears up.
To return to Auto Tracking, press POWER off,
then on again a few seconds later.
R
R
R
R
R
R
For Your
Information
Plastic surfaces are easily scratched
and can be marred by alcohol and
various solvents. Avoid excessive use
of oil-based furniture polishes since
the materials used in the cabinet will
accumulate more dust.
We recommend using a nonabrasive,
antistatic cleaner and polisher.
Power Source:
120 V AC, 60 Hz
Power Consumption: Power On
Approx. 23 watts
Power Off
Approx. 3.0 watts
Video Signal:
EIA Standard NTSC color
Video Recording System:4 rotary heads helical
scanning system
Audio Track:
1 track (Normal)
2 channel (Hi-Fi Audio
Sound)
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels:
Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5 A (01)
Ultraband 65 ~ 94, 100 ~ 125
Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight:
2.7 kg (6.0 lbs).
Dimensions:
430 (W) x 98 (H) x 242 (D) mm
16-15/16” (W) x 3-7/8” (H)
x 9-9/16” (D) inch
Note: Designs and specifications are subject to
change without notice.
R
Playing older or damaged tapes may
eventually cause video heads to
become clogged.
R
Head Cleaning
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / operate as a
V-Lock control.
37
V4622 P22-44 (2nd) [LSQT0509B].p65
37
2002/05/23, 18:29
On-Screen Displays (OSD)
Blank Tape/ No Video Signal
Indications
Function & Channel Displays
When a function button is
pressed, e.g. PLAY, or you
change channels, a 5
second display appears.
(Some Station names may
also appear if Channel
Caption is set. See page 32.)
CH 0 8
Whenever a blank section of a tape comes
up in Play mode, or when the selected
channel has no broadcast signal with the
Weak Signal Display Feature (p. 35) set to
OFF, the TV screen will turn solid blue.
VCR Status & Clock Displays
Function Status
To display or
remove overlay
at right,
➛ press DISPLAY.
PLEASE SET CLOCK BY
PRESSING ACTION KEY
Caution
16
RECORD TAB
NO CASSETTE
TO CANCEL TIMER REC
PRESS POWER THEN
STOP KEY
38
If you press REC on
the remote control or
VCR, and a cassette is
inserted with no record
tab...
Caution
If you press POWER
or STOP during a
Timer Recording...
(visible in VCR
mode only)
37
If you press a function
buttons other than
33
STOP/EJECT or
POWER while the VCR
is in VCR Lock mode...
VCR LOCK ACTIVATED
TO CABLE/DSS MODE
USE VCR : VCR KEY
If you press PLAY, FF,
14
REW, or REC on the
remote control or VCR 15
without a cassette
inserted...
Page
:PLAY
REMOTE CONTROL IS SET
4
Tape Speed
(See p. 4.)
If head cleaning
becomes necessary
while playing back a
tape...
After a Timer Program
has been set...
FOR TIMER RECORDING
CHECK CASSETTE
Time Stamp Data
( See p. 34.)
• This is not displayed
in Rec mode.
OSD
END
TURN VCR OFF
11/11/2001 SUN
12:00PM- 1:00PM
CH 08 ABC MOVIE
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
CLEANING CASSETTE
OR REFER TO MANUAL
Page
If you attempt to set or
review a Timer
Recording and the
16
Clock is not set...
Counter
These displays will alert you to a missed
operation or provide further instructions.
Warning and Instruction Displays
OSD
ABC
REC
1 2 : 0 0AM
-0 : 1 2 : 3 4
0 : 25
SP
STEREO
SAP
MONO
Rec Time Remaining
(OTR mode only,
see p. 15.)
Broadcast Audio
Being Received
(See p. 25.)
Channel
Caption
(See p. 32.)
Current Time
35
REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
If you press an invalid
22
key on the remote
while in CABLE/DSS
23
mode...
If you press an invalid 22
key on the remote
23
while in TV mode...
35
16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
38
2002/05/23, 18:29
Before Requesting Service
Check the following points if you are having trouble with your VCR.
Correction
Power
• Completely insert Power Plug into an AC outlet.
• Set POWER button to on.
• Make sure power source is active.
No power…
Recording & Playback
Correction
• Check connections between VCR, external antenna, and TV.
• Check channel selections.
• Make sure your antenna system (CABLE or TV) is correctly
set. (Channels [P. 12])
• Make sure cassette record tab is intact. (P. 4)
• Confirm that clock is set to current time and date.
Timer recording cannot be performed…
• Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
• Set recording start/stop times correctly. (P. 16)
• Make sure VCR POWER button is pressed off. (P. 16)
• Timer recording may not be performed or continued if a power
interruption occurs before or during a Timer Recording, even
after power is restored.
There is no playback picture, or the playback • Select channel 3 or 4 on TV to match VCR output channel (3
or 4) (P. 8) or select LINE.
picture is noisy or contains streaks...
• Set VCR/TV selector to “VCR.”
• Adjust TRACKING control in either direction. (P. 37)
• Try Head Cleaning. (P. 37)
During special effects playback, picture may
• Set TV’s Vertical Hold Control to MANUAL, then adjust.
contain some vertical jitter when using a TV
with an Automatic Vertical Hold Control...
• Make sure VCR power is on.
VCR cannot be controlled...
• Check Remote batteries.
• Make sure VCR LOCK is set to off. (P. 33)
• Make sure Remote is in proper mode. (P. 22)
• Make sure Timer Recording is not in progress.
TV program cannot be recorded...
Correction
Remote Control
•
•
•
•
•
•
•
VCR cannot be remote controlled...
ACTION and PROG/VCR+ buttons do not
respond...
Make sure VCR power is on.
Make sure Remote is in VCR mode.
Aim Remote Control directly at remote sensor on VCR. (P. 6)
Avoid any object blocking signal path.
Check Remote batteries. (P. 4)
Make sure VCR LOCK is set to off. (P. 33)
Exposing VCR remote sensor to direct fluorescent or outdoor
light may cause signal interference.
• Check connections between VCR, external antenna, and TV.
• Press VCR button for VCR mode. (P. 22)
• Check Remote batteries. (P. 4)
Correction
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Make sure TV power is on.
Make sure TV is set to output of VCR.
Check connections between VCR, external antenna, and TV.
Set VCR/TV selector to “TV.” (P. 15)
Make sure proper signal source is selected.
Insert the cassette with window side up; record tab facing you.
Check if a tape is already in the unit.
Completely insert Power Plug into an AC outlet.
Video cassette cannot be removed...
Video cassette ejects when a recording is started • Make sure cassette record tab is intact. (P. 4)
or the power is turned off for timer recording...
• To enable Quick play mechanism, the cylinder will rotate for
In Stop mode, the motor (CYLINDER)
about 3 minutes. This reduces response time from Stop to
continues to rotate...
Play mode and from Play to Rewind Search mode.
If you cannot resolve the problem, please call the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : [email protected]
For Your
Information
•
•
•
•
•
•
•
•
39
V4622 P22-44 (2nd) [LSQT0509B].p65
39
2002/05/23, 18:29
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way
Secaucus, New Jersey 07094
PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Panasonic VHS VCR Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively
referred to as “the warrantor”) will, for the length of the period indicated on the chart below,
which starts with the date of original purchase (“warranty period”), at its option either (a)
repair your product with new or refurbished parts, or (b) replace it with a new or a
refurbished product. The decision to repair or replace will be made by the warrantor.
Parts
Labor
All components of VCR
except item listed below
One (1) Year
Ninety (90) Days
Video Tape (in exchange
for defective video tape)
Five (5) Days
Not Applicable
Product or Part Name
During the “Labor” warranty period there will be no charge for labor. During the “Parts”
warranty period, there will be no charge for parts. You must mail-in your product during the
warranty period. If non-rechargeable batteries are included, they are not warranted.
This warranty only applies to products purchased and serviced in the United States or
Puerto Rico. This warranty is extended only to the original purchaser of a new product
which was not sold “as is”.
Mail-In Service
For assistance in the continental U.S.A. in obtaining repairs please ship the product to:
Panasonic Services Company
Customer Servicenter
Suite B
4900 George McVay Drive
McAllen, TX 78503
For assistance in Puerto Rico call Panasonic Sales Company
(787) 750-4300 or fax (787)768-2910
When shipping the unit carefully pack and send it prepaid, adequately insured and
preferably in the original carton. Include a letter detailing the complaint and provide a day
time phone number where you can be reached.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BE
REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING
DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED
WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty continued on next page.
40
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
40
2002/05/23, 18:29
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES
NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are caused by products not
supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect,
mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment
of consumer controls, improper maintenance, power line surge, lightning damage,
modification, introduction of sand, humidity or liquids, commercial use such as hotel, office,
restaurant, or other business or rental use of the product, or service by anyone other than a
Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED
WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR
ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes
damages for lost time, cost of having someone remove or re-install an installed unit if
applicable, travel to and from the servicer, loss of or damage to media or images, data or other
recorded content. The items listed are not exclusive, but are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state. If a problem with this product develops during or after the warranty period, you may
contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to
the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE
YOUR RESPONSIBILITY.
Customer Services Directory
For Product Information, Operating Assistance, Literature Request, Dealer Locations,
and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.
or send e-mail : [email protected]
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
For Your
Information
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
As of April 2002
41
V4622 P22-44 (2nd) [LSQT0509B].p65
41
2002/05/23, 18:29
Spanish Quick Use Guide/ Guía para rápida consulta
Conexiones/Configuracion
Inicial
Para
ajustar el idioma, canal
y (READY TO PLAY)
Favor realice la conexion de antena o cable antes de conectar el cordon de AC a la toma de
pared. Conectando el cordon de AC de la VCR en toma de pared iniciara automaticamente la
busqueda de canales y colocacion de tiempo. PRECAUCION
Si se sobre ajusta “NUT TYPE” el cable coaxial RF podria dañar las
terminales de conexion. Ajusta ligeramente utiliza solo los dedos.
Conectando
Para Ant/Cable ➛ VCR ➛ TV
1
2
VCR
Terminal IN FROM ANT.
Televisor
Conecte Ant/Cable a la entrada de antena
de la VCR (VCR In)
Conecte la salida de la VCR (VCR Out) a la
entrada de antena de la TV (TV In) con el
cable-accesorio RF incluido.
1
Entrada (IN) desde
ANT./CABLE
Terminal
OUT TO TV
2
VHF/UHF
Para Sistema Digital de Satelite (DSS)/ Convertidor de cable ➛ VCR ➛ TV
1
2
Conecte la salida del convertidor de cable
a la ”VCR In” con el RF cable accesorio
incluido.
Conecte “VCR Out” a la “TV In” con el
cable-accesorio incluido.
Televisor
2
Realizando configuracion inicial
1
2
Presione el boton VCR del control remoto
para dicha modalidad. Encienda la TV y
cambie a canal 3.
Conecte cordon de AC de la VCR a la toma
de pared. La VCR se activara e iniciara
busqueda de canales y colocacion de
tiempo.
• Si la pantalla abajo no aparece cheque la
conexion VCR-TV y si la TV fue cambiada a el
canal 3,trate cambiando a el canal 4.
• Para cambios a el canal de salida de la VCR favor
hacer referencia a “VCR’s Output Channel” (p. 19).
Conectando cordon de AC a la toma de pared.
Terminal
IN FROM ANT.
VCR
Terminal
OUT TO TV
Estuche convertidor
de TV por cable
1
Entrada (IN) desde
ANT./CABLE
VHF/UHF
3
Selecciones se realizaron automaticamente
cuando la configuracion termino, esta
VCR C / A
CLOCK
CH
pantalla aparece.
9 /29 / 2002 SUN 2 : 20PM
DST : ON
SETT I NG : CH 10
AUTO CLOCK SET
COMPLETED
4
SELECCION DE CONEXION en el menu
desplegado en pantalla.
➛ VCR➛
➛ TV.)
■ (Si la conexion es ANT/CABLE➛
* para obtener las
Presione
conexiones “VCR
TV”, o “VCR
CABLE/DSS TV”, y presione
VCR C / A CLOCK CHANNEL
seleccionar.
SELECT CONNECTION
VCR TV
CABLE / DSS BOX VCR TV
VCR CABLE / DSS BOX TV
Al inicio, el idioma de la
pantalla está fijado a
inglés.
Para cambiar el
idioma consulte la
página 12.
■ (Si la conexion es DSS/Convertidor de
➛ VCR➛
➛ TV.)
cable➛
Presione
para obtener la conexion
“CABLE/DSS VCR TV” y presione
para seleccionar.
VCR C / A CLOCK CHANNEL
Si usa convertidor de cable solo enciendala y seleccione
el canal PBS en su horario de uso u horario de zona.
Si utiliza receptor DSS este debe estar apagado.
Confirme el canal de salida de su
convertidor de cable o receptor de DSS
presione
que permitiran selecionar el
mismo canal de salida que su convertidor
VCR C / A CLOCK CHANNEL
o DSS.
SELECT CONNECTION
CABLE / DSS BOX VCR TV
Presione
para seleccion.
CH AUTO SET PROCEEDING
CANCEL : STOP
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
SELECT CONNECTION
VCR TV
CABLE / DSS BOX VCR TV
VCR CABLE / DSS BOX TV
CABLE / DSS BOX OUTPUT CH
CH 0 1
Realizando configuracion inicial
Si la colocacion de tiempo fue incompleta.
Presione la tecla ACTION en el control remoto
para visualizar la pantalla del menú RELOJ.
Presione
para seleccionar el mes y para
ajustar. De la misma forma, seleccione y ajuste
la fecha, año, hora y DST (Hora de Verano).
a
b
VCR
C/A
1/ /
RELOJ
CANAL
:
VCR
42
RELOJ
CANAL
VERANO : ACT
VERANO : ACT
ELEGIR MES
C/A
9 /29 / 2002 DOM 2 : 20PM
FIJACION ES COMPLETO
Si “AUTO CLOCK SET IS INCOMPLETE”
aparece, coloque manualmente el tiempo,
vealo abajo.
VCR C / A
CLOCK
CH
AUTO CLOCK SET IS
INCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACTION KEY
c
Presione dos veces la tecla ACTION
para poner el RELOJ en marcha y pase
al paso 4 anterior.
For assistance,
Por
ayuda llame
please
al 1-800-211-PANA(7262)
call : 1-800-211-PANA(7262)
o envie
or send
e-mail
e-mail
a : to
[email protected]
: [email protected]
V4622 P22-44 (2nd) [LSQT0509B].p65
42
2002/05/23, 18:29
*Importante:Si un botón del control remoto no funciona al ser presionado,
presione el botón VCR del control remoto y vuelva a intentarlo.
Operaciones básicas para la
reproducción
Programación fácil para la
grabación con temporizador
PROG/VCR+
1 Inserte un cassette,
1 Presione
para visualizar PROGRAM.
Presione
PLAY
para
reproducir
el
cassette.
2 • Si el cassette no tiene lengüeta de prevención
de grabación (página 4), se inicia la reproducción
2 7 SAB --:-- --:-- -- Presione
automáticamente.
para visualizar la pantalla
VCR Plus+
PROG. L I STA
FECHA I N I C I O PARADA CA
Detalles especiales durante la grabación
Presione FF o REW para búsqueda de
escenas hacia delante/ hacia atrás.
Presione PLAY para liberar.
Presione FF o REW para búsqueda de escenas
Hacia delante/ Hacia atrás. Presione PLAY para
liberar. Despues que la busqueda ha iniciado.
Presione FF o REW en cada uno de los cambios
de velocidades mostradas abajo.
[SLP] aprox. 43X ↔ aprox. 21X
[LP] aprox. 15X ↔ aprox. 9X
[SP] aprox. 13X ↔ aprox. 7X
Si a velocidad de 43X, 15X, o 13X la imagen se
interrumpe cambie a velocidad 21X, 9X o 7X.
Presione PAUSE/SLOW para imagen Fija
(Congelada). Presione PLAY para liberar.
Presione PAUSE/SLOW en el modo de
imagen fija para imágenes cuadro a
cuadro. Presione PLAY para liberar.
Mantenga presionado PAUSE/SLOW en
el modo de imagen fija para imágenes en
cámara lenta. Presione PLAY para liberar.
HOY
CATEGORIA : NO
ELEGIR
SAL I R
3
SLP
VCR Plus+
PROG. L I STA
FECHA I N I C I O PARADA CA
7 SAB --:-- --:-- -HOY
SLP
CATEGORIA : NO
ELEGIR FECHA DE I N I C I O
ELEGIR :
FIJAR :
TERMINAR : PROG
Orden para elegir
Ejemplo
Fecha de hoy 7
Operaciones básicas para la
grabación
el cassette con lengüeta de
1 Inserte
protección de grabación (pág. 4).
CH
, o las teclas de
2 Presione
números para seleccionar el canal.
SPEED para seleccionar la
3 Presione
velocidad de grabación (pág.4)
PAUSE/SLOW para pausar, y al presionar
nuevamente se reanuda la grabación.
• No podrá ver otro canal durante la grabación.
5 Presione STOP para detener la grabación
Grabación de Un Toque (grabar en marcha),
• El VCR se apaga después de preajustar la
extensión de la grabación.
➛ Cada vez que se presiona REC se
añaden 30 min. a la extensión de
grabación hasta un máximo de 4 horas.
V4622 P22-44 (2nd) [LSQT0509B].p65
43
9
/
31
1
2
6
Orden para elegir
SEMANAL
(LUN)
DIARIO
SEMANAL
(DOM)
**Categoría
NO, DEPORTE, CINE, COMEDIA,
MUSICA, DRAMA
4
VCR Plus+
PROG.
L I STA
FE I N I C
PARADA CA VEL
7
2 : 00 P
3 : 20 P 02 SLP
-- -- : --- : --- --- -- : --- : --- --- : --- --- -- : -CANCELAR: ADD / DLT
ELEGIR :
FIJAR :
SAL I R
: PROG
Presione
para
seleccionar un número
que no está usando para
ingresar mas programas
y presione para
ajustar. Luego repita el
paso 3.
Presione nuevamente
PROG/VCR+ para salir.
Guía para rápida
consulta
4 • Para eliminar escenas indeseadas, presione
Presione REC para comenzar a grabar.
8
2) Para ajustar los
ítems que quedan,
presione
para
seleccionar y
para ajustar
presione
los tiempos de
INICIO/PARADA,
CANAL, o entrada de
LÍNEA (pág. 36),
CATEGORIA**, y
velocidad del cassette
(SP, LP, SLP).
Presione PROG/VCR+
para finalizar el programa.
Presione REW o FF en el modo de parada
para rebobinado/avance rápido del cassette.
Presione EJECT en el control remoto, o
STOP/EJECT en el VCR para expulsar la
cassette.
= Reproducción estándar,
= Larga duración,
= Superlarga duración.
1) Para ajustar la
FECHA de grabación,
presione
para
seleccionar:
1-31 = una vez, o
DIARIO = a la misma
hora de lunes a viernes,
o SEMANA = a la misma
hora cada semana y
presione para ajustar.
SEMANAL
(SAB)
3 Presione STOP para detener el cassette.
• SP
• LP
• SLP
de Programación.
:
: PROG
POWER off para ajustar el
5 Presione
temporizador.
(Se ilumina “TIMER” en el panel delantero)
2002/05/23, 18:29
43
Index
A
Accessories ...................................................... 4
AC Power Plug .................................................. 7
Add or Delete a Channel ................................ 13
Audio Input Connector (L/R) ............................ 7
Audio Output Connector (L/R) ......................... 7
Audio/Video Connection ................................. 24
Auto Operation Functions .............................. 31
Auto Shut-Off .................................................. 35
Auto VCR Plus+ System Channel Setup .. 18, 19
B
Batteries ............................................................ 4
Before Requesting Service ............................ 39
Blank Tape/ No Video Signal Indications ...... 38
C
Cable Box Setup ............................................. 10
Cassette Compartment .................................... 6
Channel Caption ............................................. 32
Channel Up/Down Tracking/V-Lock Button ... 6
Cleaning the VCR ........................................... 37
Clock/Status/Channel/Speed Display ............. 7
Commercial Advance ........................ 26, 27, 28
Connections ......................................... 8, 10, 24
Copying Your Tapes ...................................... 36
Customer Services Directory ........................ 41
D
DST (Daylight Saving Time) .......................... 13
F
Fast Forward/Search Button ........................... 6
Features for a Quality Picture ...................... 37
Function & Channel Displays ........................ 38
H
Head Cleaning ................................................ 37
Hi-Fi Indicator ................................................... 7
I
Important Safeguards and Precautions .......... 2
Index Search ................................................... 30
Initial Setup ................................................ 8 - 11
L
Limited Warranty ..................................... 40, 41
M
Manual VCR Plus+ System Channel Setup ... 20
Movie Advance ............................................... 29
MTS Broadcast ............................................... 25
Multi-Brand Control .................................. 22, 23
O
On-Screen Display ......................................... 38
P
Playback ......................................................... 14
Play Button ........................................................ 6
Power Button ..................................................... 6
Power Indicator ................................................ 7
Program End Search ...................................... 30
R
Record ............................................................ 15
Record Button ................................................... 6
Remote Control Buttons ................................... 6
Remote Sensor ................................................. 6
Remote Warning ON/OFF ............................. 33
Repeat Play ..................................................... 31
Reset Language, Channels, Clock,
VCR’s Output Channel ......................... 12, 13
Review, Replace or Clear
Program Contents ....................................... 17
Rewind/Search Button ...................................... 6
S
Select Audio Mode .......................................... 25
Shuttle Variable Speed Search ...................... 35
Spanish Quick Use Guide ...................... 42, 43
Specifications .................................................. 37
Stereo/SAP/Mono Broadcast ......................... 25
Stop/Eject Button .............................................. 6
T
Table of Contents ............................................ 5
Tape Position and Tape Status ..................... 34
Time Stamp ..................................................... 34
Timer Indicator ................................................. 7
Timer Recording ...................................... 16, 17
Timer Recording Using
VCR Plus+ System .............................. 18 - 21
V
VCR Indicator .................................................... 7
VCR Lock ........................................................ 33
VCR Plus+ System Programming ................. 21
VCR Status & Clock Displays ....................... 38
VCR/TV Selector ....................................... 6, 35
VHF/UHF Antenna Input Terminal .................. 7
VHF/UHF Antenna Output Terminal ............... 7
Video Input Connector (L/R) ............................ 7
Video Output Connector (L/R) ......................... 7
W
Warning and Instruction Displays ................. 38
Weak Signal Display ON/OFF ....................... 35
Z
Zero Search .................................................... 31
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
P
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
V4622 P22-44 (2nd) [LSQT0509B].p65
44
2002/05/23, 18:29
Printed in Indonesia
LSQT0509B
S1201-1052
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement