Panasonic | TXLF37E30 | Operating instructions | Panasonic TXLF32E30 Operating Instructions

Panasonic TXLF32E30 Operating Instructions
Model No.
TX-LF32E30
TX-LF37E30
TX-LF42E30
Operating Instructions
LCD Television
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before operating this product and retain
them for future reference.
The images shown in this manual are for illustrative purposes only.
Please refer to Pan European Guarantee Card if you need to contact your local
Panasonic dealer for assistance.
English
TQB0E2098U
Experience an amazing level of multimedia
excitement
Enjoy rich multimedia
USB device
Camcorder
SD Card
Network
Personal computer
Amplifier with
Speaker system
Set top box
DVD Recorder
VCR
DVD Player
Blu-ray Disc Player
USB HDD
Notice for DVB functions
This TV is designed to meet the standards (as of August, 2009) of DVB-T (MPEG2 and MPEG4-AVC(H.264)) digital
terrestrial services and DVB-C (MPEG2 and MPEG4-AVC(H.264)) digital cable services.
Consult your local dealer for availability of DVB-T services in your area.
Consult your cable service provider for availability of DVB-C services with this TV.
TV may not work correctly with the signal which does not meet the standards of DVB-T or DVB-C.
• This
all the features are available depending on the country, area, broadcaster and service provider.
• Not
all CI modules work properly with this TV. Consult your service provider about the available CI module.
• Not
TV may not work correctly with CI module that is not approved by the service provider.
• This
fees may be charged depending on the service provider.
• Additional
compatibility with future DVB services is not guaranteed.
• The
the latest information on the available services at the following website. (English only)
• Check
http://panasonic.jp/support/global/cs/tv/
2
Transport only in upright position
The recording and playback of content on this or any other
device may require permission from the owner of the copyright
or other such rights in that content. Panasonic has no authority
to and does not grant you that permission and explicitly
disclaims any right, ability or intention to obtain such permission
on your behalf. It is your responsibility to ensure that your use
of this or any other device complies with applicable copyright
legislation in your country. Please refer to that legislation for
more information on the relevant laws and regulations involved
or contact the owner of the rights in the content you wish to
record or playback.
Contents
Be Sure to Read
Safety Precautions····································································4
Maintenance ··············································································5
Quick Start Guide
Accessories / Options······························································6
Identifying Controls ·································································8
Basic Connection ··································································· 10
This product is licensed under the AVC patent portfolio license
for the personal and non-commercial use of a consumer to (i)
encode video in compliance with the AVC Standard (“AVC Video”)
and/or (ii) decode AVC Video that was encoded by a consumer
engaged in a personal and non-commercial activity and/or was
obtained from a video provider licensed to provide AVC Video.
No license is granted or shall be implied for any other use.
Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
Auto Setup ··············································································· 12
Enjoy your TV!
Basic Features
Using “VIERA Connect” ························································ 16
Watching TV ············································································ 17
ROVI CORPORATION AND/OR ITS RELATED AFFILIATES ARE NOT
IN ANY WAY LIABLE FOR THE ACCURACY OF THE PROGRAM
SCHEDULE INFORMATION PROVIDED BY THE GUIDE PLUS+
SYSTEM. IN NO EVENT SHALL ROVI CORPORATION AND/
OR ITS RELATED AFFILIATES BE LIABLE FOR ANY AMOUNTS
REPRESENTING LOSS OF PROFITS, LOSS OF BUSINESS,
OR INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES
IN CONNECTION WITH THE PROVISION OR USE OF ANY
INFORMATION, EQUIPMENT, OR SERVICES RELATING TO THE
GUIDE PLUS+ SYSTEM.
http://www.europe.guideplus.com/
Using TV Guide ······································································· 21
Viewing Teletext····································································· 24
Watching External Inputs ··················································· 26
How to Use VIERA TOOLS ··················································· 28
How to Use Menu Functions ············································· 29
Advanced Features
Retuning from Setup Menu ··············································· 37
Tuning and Editing Channels (DVB) ······························· 39
Tuning and Editing Channels (Analogue)····················· 42
Timer Programming ····························································· 44
Child Lock ················································································· 46
Input Labels ············································································· 48
Using Common Interface ··················································· 49
Shipping Condition ······························································ 50
Updating the TV Software·················································· 51
Displaying PC Screen on TV ··············································· 52
USB HDD Recording ····························································· 53
Using Media Player ······························································· 57
Using Network Services (DLNA / VIERA Connect)··········· 69
Link Functions (Q-Link / VIERA Link) ······························· 80
External Equipment ······························································ 89
FAQs, etc.
Technical Information ·························································· 92
FAQs ··························································································· 99
Licence ····················································································101
Specifications ········································································102
3
Safety Precautions
Warning
Safety Precautions
Handling the mains plug and lead
the mains plug fully into the socket outlet. (If the mains plug is loose, it could generate heat and cause fire.)
• Insert
that the mains plug is easily accessible.
• Ensure
not touch the mains plug with a wet hand. This may cause electrical shock.
• Do
the mains lead, damaged lead may cause fire or electrical shock.
• Do• Donotnotdamage
move the TV with the lead plugged into a socket outlet.
•
•
•
•
•
Do not place a heavy object on the lead or place the lead near a high temperature object.
Do not twist the lead, bend it excessively or stretch it.
Do not pull on the lead. Hold onto the mains plug body when disconnecting the plug.
Do not use a damaged mains plug or socket outlet.
Ensure the TV does not crush the mains lead.
If you find any
abnormality,
remove the mains plug
immediately!
AC 220-240 V
50 / 60 Hz
Power source / Installation
Do not expose to rain or
excessive moisture
TV is designed for:
• This
• AC 220-240 V, 50 / 60 Hz
• Table-top use
Do not remove covers and
NEVER modify the TV yourself
voltage components may cause serious electrical
• High
shock, do not remove the rear cover as live parts are
•
•
accessible when it is removed.
There are no user serviceable parts inside.
Have the TV checked, adjusted or repaired at your local
Panasonic dealer.
Do not expose the TV to direct sunlight and
other sources of heat
damage which might result in electric shock or
• Tofire,prevent
do not expose this TV to rain or excessive moisture.
TV must not be exposed to dripping or splashing
• This
water and objects filled with liquid, such as vases, must
not be placed on top of or above the TV.
Do not place foreign objects inside the TV
not allow any objects to drop into the TV through the
• Do
air vents as fire or electric shock may result.
Do not place the TV on sloped or unstable
surfaces, and ensure that the TV does not
hang over the edge of the base
• The TV may fall or tip over.
exposing the TV to direct sunlight and other sources
• Avoid
of heat.
Use only original dedicated pedestal /
To prevent the spread
of fire, keep candles or
other open flames away
from this product at all
times
mounting equipment
an unapproved pedestal or other fixtures may make
• Using
the TV unstable, risking injury. Be sure to ask your local
Panasonic dealer to perform the setup or installation.
approved pedestals (p. 7) / wall-hanging brackets
• Use
(p. 6).
Do not allow children to handle SD Card or
dangerous parts
any small object, the SD Card could be swallowed
• Asby with
young children. Please remove SD Card immediately
after use and store out of reach of children.
product contains possibly dangerous parts that
• This
can be breathed in or swallowed by young children
accidentally. Keep these parts out of reach of young
children.
4
Caution
Do not block the rear air vents
• Cleaning an energized TV may cause electric shock.
Remove the mains plug from the wall socket
when the TV is not in use for a prolonged
period of time
TV will still consume some power even in the Off mode,
• This
as long as the mains plug is still connected.
Do not expose your ears to excessive volume
from the headphones
• Irreversible damage can be caused.
Do not apply strong force or impact to the
display panel
• This may cause damage resulting in injury.
ventilation is essential to prevent failure of
• Adequate
electronic components.
should not be impeded by covering the
• Ventilation
ventilation openings with items such as newspapers, table
cloths and curtains.
recommend that a gap of at least 10 cm is left all
• We
around this TV even when placed inside a cabinet or
between shelves.
using the pedestal, keep the space between the
• When
bottom of the TV and the surface where the TV is set.
is not used, ensure the vents in the bottom of
• Ifthepedestal
TV are not blocked.
Minimum distance
Safety Precautions | Maintenance
When cleaning the TV, remove the mains
plug
10
10
10
10
(cm)
Maintenance
First, remove the mains plug from the socket outlet.
Display panel, Cabinet, Pedestal
Regular care :
Gently wipe the surface of the display panel, cabinet,
or pedestal by using a soft cloth to clean the dirt or
fingerprints.
For stubborn dirt :
Dampen a soft cloth with clean water or diluted neutral detergent
(1 part detergent to 100 parts water). Then wring the cloth and
wipe the surface. Finally, wipe away all the moisture.
Caution
not use a hard cloth or rub the surface too hard. This may cause scratches on the surface.
• Do
care not to subject the TV’s surfaces to water or detergent. A liquid inside the TV could lead to product failure.
• Take
care not to subject the surfaces to insect repellent, solvent, thinner or other volatile substances. This may degrade
• Take
surface quality or cause peeling of the paint.
surface of the display panel is specially treated and may be easily damaged. Take care not to tap or scratch the surface
• The
with your fingernail or other hard objects.
not allow the cabinet and pedestal to make contact with a rubber or PVC substance for a long time. This may degrade
• Do
surface quality.
Mains plug
Wipe the mains plug with a dry cloth at regular intervals. Moisture and dust may lead to fire or electrical shock.
5
Accessories / Options
Standard accessories
Remote Control
N2QAYB000490
or
N2QAYB000672
Batteries for the
Remote Control (2)
R6
(p. 7)
•
•
Pedestal
(p. 7)
•
Quick Start Guide
Operating Instructions
Pan European Guarantee Card
may not be placed all together. Take care not to throw them away unintentionally.
• Accessories
product contains possibly dangerous parts (such as plastic bags), that can be breathed in or swallowed by young
• This
children accidentally. Keep these parts out of reach of young children.
Accessories / Options
Optional accessories
Please contact your nearest Panasonic dealer to purchase the recommended optional accessories. For additional details, please
refer to the manual of the optional accessories.
Wireless LAN Adaptor
• DY-WL10E-K
Caution
the Wireless LAN Adaptor, an access point needs to be obtained.
• ToIt isuserecommended
to use the Wireless LAN Adaptor with the extension cable.
• To avoid malfunctions
caused by radio wave interference, keep the TV away from the devices such
• as other wireless LAN devices,
microwaves and the devices that use 2.4 GHz and 5 GHz signals when
using the Wireless LAN Adaptor.
on the area, this optional accessory may not be available.
• Depending
information for Wireless LAN Adaptor and access point may be on the following website.
• Additional
(English only)
http://panasonic.jp/support/global/cs/tv/
Communication Camera
TY-CC10W
Caution
•
camera can be used on VIERA Connect (p. 79).
• This
also read the manual of the camera.
• Please
on the area, this optional accessory may not be available.
• Depending
For details, consult your local Panasonic dealer.
Wall-hanging bracket
TY-WK3L2RW
The angle of wall-hanging bracket can
be adjusted in “zero tilting (vertical)”
and “10-degree tilting” for this TV.
•
Rear of the TV
Screw for fixing the TV onto the wall-hanging
bracket (not supplied with the TV)
200 mm
Depth of screw :
minimum 4 mm,
maximum 17 mm
Diameter : M6
200 mm
(View from the side)
Holes for wall-hanging bracket installation
Warning
to use a Panasonic bracket or choosing to mount the unit yourself will be done at the risk of the consumer. Always
• Failure
be sure to ask a qualified technician to carry out set up. Incorrect fitting may cause equipment to fall, resulting in injury and
product damage. Any damage resulting from not having a professional installer mount your unit will void your warranty.
any optional accessories or wall hanging brackets are used, always ensure that the instructions provided are followed fully.
• When
not mount the unit directly below ceiling lights (such as spotlights or halogen lights) which typically give off high heat.
• Do
Doing so may warp or damage plastic cabinet parts.
care when fixing wall brackets to the wall. Wall mounted equipment shall not be grounded by metal within the wall.
• Take
Always ensure that there are no electrical cables or pipes in the wall before hanging bracket.
• To prevent fall and injury, remove the TV from its fixed wall position when it is no longer in use.
6
Attaching the pedestal
Warning
Do not disassemble or modify the pedestal.
Otherwise the TV may fall over and become damaged, and personal injury may result.
•
Caution
Do not use any pedestal other than the one provided with this TV.
Otherwise the TV may fall over and become damaged, and personal injury may result.
Do not use the pedestal if it becomes warped or physically damaged.
If you use the pedestal while it is physically damaged, personal injury may result. Contact your nearest Panasonic dealer
immediately.
During assembly, use only screws supplied and make sure that all screws are securely tightened.
If sufficient care is not taken to ensure screws are properly tightened during assembly, the pedestal will not be strong enough
to support the TV. It might fall over and become damaged and personal injury may result.
Ensure that the TV does not fall over.
If the TV is knocked or children climb onto the pedestal with the TV installed, the TV may fall over and personal injury may
result.
Two or more people are required to install and remove the TV.
If two or more people are not present, the TV may be dropped, and personal injury may result.
•
•
•
C Bracket
TBL5ZA3017
TX-LF32E30
TX-LF37E30
A Assembly screw (4)
•
M5 × 15
(
)
D Base
TBL5ZX0140 (TX-LF32E30)
TBL5ZX0144 (TX-LF37E30)
TBL5ZX0149 (TX-LF42E30)
• TBL5ZA3014
(TX-LF42E30)
B Assembly screw (4)
•
•
•
Accessories / Options
•
Quick Start Guide
•
M4 × 30
1
Assembling the pedestal
Use the assembly screws A to fasten the bracket
C to the base D securely.
Make sure that the screws are securely
tightened.
Forcing the assembly screws the wrong way
will strip the threads.
A
2
•
•
•
•
C
D
Securing the TV
Use the assembly screws B to fasten securely.
Tighten the four assembly screws loosely at first, then tighten
them firmly to fix securely.
Carry out the work on a horizontal and level surface.
B
B
Hold the bracket not to
fall over
Front
Foam mat or thick soft cloth
Installing / removing remote’s batteries
1
Caution
Pull open
Hook
2
Close
Note the correct
polarity (+ or -)
installation may cause battery leakage and corrosion, resulting
• Incorrect
in damage to the remote control.
not mix old and new batteries.
• Do
only with same or equivalent type. Do not mix different battery
• Replace
types (such as alkaline and manganese batteries).
not use rechargeable (Ni-Cd) batteries.
• Do
not burn or break up batteries.
• Do
not expose batteries to excessive heat such as sunshine, fire or the like.
• Do
sure you dispose of batteries correctly.
• Make
batteries are replaced correctly, there is danger of explosion and
• Ensure
fire if battery is reversed.
• Do not disassemble or modify the remote control.
7
Identifying Controls
Remote Control
8 OK
SD CARD
MENU ASPECT
DIRECT TV REC
EXIT
VIERA
Lin
k
TO
VIERA OLS
IDE
GU
Quick Start Guide
1
2
3
4
5
6
7
INPUT
TV
AV
8
BACK/
RETURN
OPTION
15
16
17
18
19
20
21
9
Identifying Controls
22
TEXT STTL INDEX HOLD
10
11
abc
12
23
24
selections and choices
• Confirms
after selecting channel positions to quickly
• Press
change channel
• Displays the Channel List
9 [Option Menu] (p. 19)
• Easy optional setting for viewing, sound, etc.
10 Teletext (p. 24)
• Switches to teletext mode
11 Subtitles (p. 18)
• Displays subtitles
12 Numeric buttons
channel and teletext pages
• Changes
characters
• Sets
in Standby mode, switches TV On (Press for
• When
about 1 second)
13 Sound Mute
• Switches sound mute On or Off
def
ghi
jkl
mno
pqrs
tuv
wxyz
14 Volume Up / Down
15 Input mode selection
- switches DVB-C / DVB-T / Analogue mode
• TV (p. 17)
- switches to AV input mode from Input Selection
• AV
list (p. 26)
25
13
LAST VIEW
16 Direct TV Recording
26
14
17 [VIERA Connect]
REC
PROGRAMME
27
DVD/VCR
TV
(p. 82, 84)
programme immediately in DVD Recorder /
• Records
VCR with Q-Link or VIERA Link connection
(p. 16, 79)
• Displays VIERA Connect home screen
18 Exit
• Returns to the normal viewing screen
19 TV Guide (p. 21)
20 Cursor buttons
• Makes selections and adjustments
• Returns to the previous menu / page
21 Return
TV
22 Coloured buttons
2
3
4
•
•
Switches TV On or Off standby
[Media Player] (p. 57)
Switches to SD Card and USB device viewing /
listening mode
[Main Menu] (p. 29)
Press to access Picture, Sound, Timer and Setup
Menus
Aspect (p. 20)
Changes aspect ratio
Information (p. 18)
Displays channel and programme information
VIERA TOOLS (p. 28)
Displays some special feature icons and accesses
easily
[VIERA Link Menu] (p. 84)
•
•
•
6
•
5
7
8
(red-green-yellow-blue)
Used for the selection, navigation and operation of
various functions
Hold
Freeze / unfreeze picture (p. 19)
Holds the current teletext page (teletext mode)
(p. 24)
Index (p. 24)
Returns to the teletext index page (teletext mode)
Last view (p. 20)
Switches to previously viewed channel or input mode
Channel Up / Down
Connected equipment operations
(p. 27, 56, 64, 65, 87)
•
1 Standby On / Off switch
23
24
25
26
27
•
•
•
•
TV
8 Channel Up / Down, Value change (when using the F
1
button), Switching the TV On (press either button for
about 1 second when in Standby mode)
F
7
2
8
9 Changes the input mode
10 Mains power On / Off switch
to switch the mains power.
• Use
If you turned the TV Off during Standby mode by the
3
TV
11 Remote control signal receiver
11
5
12
10
6
sensor
Senses brightness to adjust picture quality when [Eco
Mode] in the Picture Menu is set to [On] (p. 30)
•
(p. 91)
Headphones jack
CI slot
12 C.A.T.S. (Contrast Automatic Tracking System)
(p. 91)
13 Power and Timer LED
: Standby
• Red
Green : On
(p. 49)
SD Card slot
(p. 57)
HDMI4 terminal
(p. 91)
6 USB 3 port (p. 91)
7 Function select
/ [Contrast] / [Brightness] / [Colour] /
• [Volume]
[Sharpness] / [Tint] (NTSC signal) / [Bass]∗ / [Treble]∗ /
[Balance] / [Auto Setup] (p. 37, 38)
∗[Music] or [Speech] mode in the Sound Menu
•
Orange : Timer Programming On
Orange (flash) :
Recording of Timer Programming, Direct TV
Recording or One Touch Recording in progress
Red with orange flash :
Standby with Timer Programming On, Direct TV
Recording or One Touch Recording
The LED blinks when the TV receives a command
from the remote control.
Identifying Controls
AV2 terminals
not place any objects between the TV remote
• Do
control signal receiver and remote control.
13
Quick Start Guide
4
1
2
3
4
5
remote control last time, the TV will be in Standby
mode when you turn the TV On with Mains power On
/ Off switch.
9
AV
Using the On Screen Displays - Operation guide
Many features available on this TV can be accessed via the On Screen Display menu.
Operation guide
How to use remote control
MENU
Operation guide will help you to operate by using the
remote control.
Example : [Sound Menu]
Main Menu
Picture
Sound
Timer
Setup
Mode
Bass
Treble
Balance
Headphone Volume
Surround
Auto Gain Control
Volume Correction
Speaker Distance to Wall
Select
EXIT
Change
Open the main menu
1/2
Move the cursor / select the menu item / select from a
range of options
0
0
0
11
Move the cursor / adjust levels / select from a range
of options
0
Access the menu / store settings after adjustments
have been made or options have been set
Music
Off
Off
Over 30cm
Selects the basic sound mode
RETURN
Page up
Page down
BACK/
RETURN
Return to the
previous menu
EXIT
Exit the menu system
and return to the
normal viewing screen
Operation guide
Auto power standby function
The TV will automatically go to Standby mode in the following conditions :
• no signal is received and no operation is performed for 30 minutes in Analogue TV mode
• [Off Timer] is active in the Timer Menu (p. 19)
• no operation is performed for the period selected in [Auto Standby] (p. 33)
This function does not affect the recording of Timer Programming, Direct TV Recording and One Touch Recording.
•
9
Basic Connection
External equipment and cables shown are not supplied with this TV.
Please ensure that the unit is disconnected from the mains socket before attaching or disconnecting any leads.
Example 1
Connecting aerial
Example 2
Connecting DVD Recorder / VCR
TV only
TV, DVD Recorder or VCR
Quick Start Guide
Rear of the TV
Terrestrial aerial
Terrestrial aerial
Rear of the TV
Cable
Cable
Basic Connection
RF cable
AC 220-240 V
50 / 60 Hz
■ How to use the clamper
bundling the mains lead
To loosen :
AC 220-240 V
50 / 60 Hz
Mains lead
RF cable
knob
Fully wired
SCART cable
Keep pushing the
knob
Bundle the cables
Mains lead
hooks
Set the tip in the
hooks
RF OUT
DVD Recorder or VCR
RF IN
RF cable
To remove from the TV:
snaps
Keep pushing both side
snaps
not bundle the RF cable and mains lead together (could cause distorted image).
• Do
cables with clampers as necessary.
• Fix
• When using the optional accessory, follow the option’s assembly manual to fix cables.
Note
to the TV’s AV1 for a DVD Recorder / VCR supporting Q-Link (p. 82).
• Connect
HDMI-compatible equipment, possible to connect to HDMI terminals (HDMI1 / HDMI2 / HDMI3 / HDMI4) by using HDMI
• For
cable (p. 89).
and VIERA Link connection (p. 80, 81)
• Q-Link
also read the manual of the equipment being connected.
• Please
the TV away from electronic equipment (video equipment, etc.) or equipment with an infrared sensor. Otherwise,
• Keep
distortion of image / sound may occur or operation of other equipment may be interfered.
10
Example 3
Connecting DVD Recorder / VCR and Set top box
TV, DVD Recorder / VCR and Set top box
Rear of the TV
Terrestrial aerial
Cable
AC 220-240 V
50 / 60 Hz
Fully wired
SCART cable
Basic Connection
Fully wired HDMI
compliant cable
Fully wired
SCART cable
Mains lead
Set top box
Quick Start Guide
RF cable
DVD Recorder or
VCR
RF cable
RF IN
RF OUT
■ Connecting to the network environment (Network connections)
To enable the network service functions (VIERA Connect, etc.), you need to connect the TV to a broadband network
environment.
If you do not have any broadband network services, please consult your retailer for assistance.
Connect with LAN cable (Wired connection) or Wireless LAN Adaptor (Wireless connection).
Setup of the network connection will start after the tuning (when first using the TV) (p. 13 - 15)
•
•
•
Rear of the TV
Wired connection
Internet
environment
LAN cable (Shielded)
Use the Shielded Twist Pair (STP) LAN cable.
•
Wireless connection
Wireless LAN Adaptor and Extension cable
“Optional accessories” (p. 6)
Connect to the USB 1, 2 or 3 port.
•
Internet
environment
Access point
Note
• For more information of the network connections
(p. 70)
11
Auto Setup
Search and store TV channels automatically.
These steps are not necessary if the setup has been completed by your local dealer.
Please complete connections (p. 10, 11) and settings (if necessary) of the connected equipment before starting Auto Setup.
For details of settings for the connected equipment, read the manual of the equipment.
•
•
Quick Start Guide
1
Plug the TV into mains socket and switch On
2
Select the language
Auto Setup
3
a few seconds to be displayed
• Takes
the red LED shows on the TV, press the Standby On / Off switch on the
• Ifremote
control for about 1 second.
Menüsprache
Deutsch
Dansk
English
Svenska
Français
Norsk
Italiano
Suomi
Español
Türkçe
Português
Еλληνικά
Nederlands
Srpyski
Hrvatski
Slovenščina
Latviešu
eesti keel
Lietuvių
select
Country
Denmark
Sweden
Norway
Finland
Luxembourg
Belgium
Netherlands
Turkey
Greece
Poland
Czech
Hungary
Slovakia
Slovenia
Croatia
Estonia
Lithuania
Others
set
on the country you select,
• Depending
select your Region or store the Child LockPIN number (“0000” cannot be stored) by
following the on screen instructions.
Select the mode you want to tune
TV Signal Selection
DVB-C
DVB-T
Analogue
Start Auto Setup
5
set
Select your country
Germany
Austria
France
Italy
Spain
Portugal
Switzerland
Malta
Andorra
4
select
Polski
čeština
Magyar
Slovenčina
Български
Română
select
tune / skip tuning
: tune (search for the available channels)
: skip tuning
Select [Start Auto Setup]
TV Signal Selection
DVB-C
DVB-T
Analogue
Start Auto Setup
select
access
Setup will start to search for TV channels and store them.
• Auto
The stored channels and sorted channel order vary depending on the country, area,
TV
broadcasting system and conditions of signal reception.
Auto Setup screen varies depending on the country you select.
12
1 [DVB-C Network Settings]
5 • Depending on the country you select, select your cable provider beforehand by following the on screen instructions.
select
[Start Auto Setup]
access
DVB-C Network Settings
Frequency
Network ID
Auto
Auto
Start Auto Setup
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
Normally set [Frequency] and [Network ID] to [Auto].
If [Auto] is not displayed or if necessary, enter [Frequency] and [Network ID] specified by your cable provider with
numeric buttons.
2 [DVB-C Auto Setup]
3 [DVB-T Auto Setup]
DVB-T Auto Setup
0%
Progress
This will take about 3 minutes.
No.
Channel Name
CBBC Channel
1
BBC Radio Wales
2
E4
3
Free TV: 3
100%
Type
Free TV
Free TV
Free TV
Pay TV: 0
Searching
Quality
100
100
100
This will take about 3 minutes.
CH
Channel Name
CBBC Channel
62
BBC Radio Wales
62
E4
62
62
Cartoon Nwk
Free TV: 4
Radio: 0
CH 5
Progress
Pay TV: 0
Searching
Quick Start Guide
DVB-C Auto Setup
69
Type
Free TV
Free TV
Free TV
Free TV
Quality
100
100
100
100
Radio: 0
logical channel number. Select your preferred channel or exit the screen
for automatic selections.
4 [Analogue Auto Setup]
5 Preset Download
Analogue Auto Setup
Scan
This will take about 3 minutes.
CH
CH 29
CH 33 BBC1
CH 2
78 CC 1
41
Channel Name
If Q-Link, VIERA Link or similar technology (p. 82, 83) compatible
recorder is connected, channel, language, country / region settings are
automatically downloaded to the recorder.
Sending Preset Data
Please wait!
0%
Analogue: 2
Auto Setup
on the country you select, the channel selection screen will
• Depending
be displayed after DVB-T Auto Setup if multiple channels have the same
100%
Remote control unavailable
Searching
downloading has failed, you can download later through the Setup
• IfMenu.
[Download] (p. 34)
6
Setup the network connection
Setup the network connection to enable the network service functions such as VIERA Connect, etc. (p. 17, 69).
To setup the wireless connection, the Wireless LAN Adaptor (optional accessory) is required.
Please note that this TV does not support wireless public access points.
Ensure the network connections (p. 11) and network environment are completed before starting setup.
Select the network type
Network Setup
[Wired] “Wired connection” (p. 11)
[Wireless] “Wireless connection” (p. 11)
•
•
Select Wired or Wireless
Wired
Wireless
Set later
select
access
• To setup later on or skip this step
EXIT
Select [Set later] or
■ [Wired]
1. Select [Auto]
Acquire IP Address
Auto
select
access
2. Go to the next step 7
(Press twice)
Connection Test
Manual
Check network cable connection.
Check acquired IP address.
Check for devices using same IP address.
Check gateway connection.
Check server connection.
Automatically setup is done and the test of the network
connection starts.
To set manually, select [Manual] and set each item. For
details (p. 72)
•
: succeeded
The test is successful
and the TV is connected
to the network.
: failed
Check the settings and
connections, and then
select [Retry].
13
6
■ [Wireless]
Select the connection type
select
Connection Type
Please select network connection type.
access
Search for access point
WPS(Push button)
[Search for access point]
Access points found automatically are listed.
1. Select your desired access point
Quick Start Guide
select
Available Access Points
No.
1
2
3
Wireless type
11n(2.4GHz)
11n(5GHz)
11n(5GHz)
SSID
Access Point A
Access Point B
Access Point C
Encrypt
Reception
access
: Encrypted access point
• To search access points again
the information of the
• For
highlighted access point
Auto Setup
(yellow)
• To set manually (p. 75)
(red)
2. Access the encryption key input mode
Encryption Key Setting
Connection will be made with the following settings:SSID : Access Point A
Authentication type : WPA-PSK
Encryption type : TKIP
Please input the encryption key.
access point is not encrypted, the confirmation screen
• Ifwillthebeselected
displayed. It is recommended to select the encrypted access
point.
Encryption key
3. Enter the encryption key of the access point
Set characters
Access Point Settings
Encryption key
select
A
B
C D
E
F
G H
I
J
K
L M N O
P
Q
R
S
T
U
V W X
Y
Z
0
1
2
3
4
5
6
7
8
9
!
:
#
a
b
c
d
e
f
g
h
i
j
k
l
m n
o
p
q
r
s
t
u
v
w
x
y
z
(
)
+
-
.
*
_
BACK/
RETURN
set
•
4. Select [Yes]
Store
You can set characters by using numeric buttons.
Access Point Settings
select
set
Encryption key is set to:XXXXXXXX
Select 'Yes' to confirm.
Select 'No' to change.
Yes
No
the encryption key, select [No].
• ToIf there-enter
connection has failed, check the encryption key, settings
• and positions
of your access point. And then, follow the on screen
instructions.
5. After the access point setting is finished, perform the connection test
Connection Test
Check access point connection.
Check acquired IP address.
Check for devices using same IP address.
Check gateway connection.
Check server connection.
: succeeded
The test is successful and the TV is connected to the
network.
: failed
Check the settings and connections, and then select
[Retry].
To set manually, select [Manual] and set each item. For
details (p. 72)
•
6. Go to the next step 7
(Press twice)
14
[WPS(Push button)]
1. Press the WPS button on the access point until the light flashes
2. Connect the Wireless LAN Adaptor and the access point
6
WPS(Push button)
1) Please press the ‘WPS’ button on the access
point until its light flashes.
2) When the light is flashing select ‘Connect’ on
TV.
If you are unsure, please check the instruction
manual of the access point.
Connect
that your access point supports WPS for this setup.
• Ensure
: Wi-Fi Protected Setup™
• WPS
the connection has failed, check the settings and positions of your
• Ifaccess
point. And then, follow the on screen instructions.
Connection Test
: succeeded
The test is successful and the TV is connected to the
network.
Check access point connection.
Check acquired IP address.
Check for devices using same IP address.
Check gateway connection.
Check server connection.
•
(Press twice)
7
Select [Home]
Auto Setup
: failed
Check the settings and connections, and then select
[Retry].
To set manually, select [Manual] and set each item. For
details (p. 72)
4. Go to the next step 7
Quick Start Guide
3. After the access point setting is finished, perform the connection test
Select [Home] viewing environment to use in your home environment.
Please select your viewing environment.
Home
select
set
Shop
■ [Shop] viewing environment (for shop display only)
[Shop] viewing environment is the demonstration mode to explain main features of this TV.
Select [Home] viewing environment to use in your home environment.
You can return to viewing environment selection screen at the stage of Shop confirmation screen and Automatic
Demo Off / On selection screen.
•
1 Return to viewing environment selection
screen
Please select your viewing environment.
Home
Shop
You have selected shop mode
Automatic Demo
Off
2 Select [Home]
select
set
Shop
BACK/
RETURN
On
To change viewing environment later on, you will need to initialise all settings by accessing Shipping Condition.
[Shipping Condition] (p. 50)
Auto Setup is now complete and your TV is ready for viewing.
If tuning has failed, check the connection of the RF cable, and then, follow the on screen instructions.
Note
channel list at-a-glance “Using TV Guide” (p. 21)
• ToTo check
or hide (skip) channels “Tuning and Editing Channels” (p. 39 - 43)
• To edit
all channels [Auto Setup] (p. 37, 38)
• To retune
the available TV mode later [Add TV Signal] (p. 34, 35)
• To add
• initialise all settings [Shipping Condition] (p. 50)
If you connect the Wireless LAN Adaptor later on, the confirmation screen will be
displayed for the setup.
To setup the wireless connection (p. 73 - 75)
•
Wireless LAN adaptor connection
Wireless LAN adaptor connected, do you want to
set it up?
No - Exit
Current network type : Wireless
Yes
No
15
Using “VIERA Connect”
VIERA Connect is a gateway to the internet services unique to Panasonic and has expanded VIERA CAST features greatly.
VIERA Connect allows you to access some specific websites supported by Panasonic, and enjoy internet contents such as
photos, videos, games, etc. from VIERA Connect home screen.
This TV has no full browser function and all features of websites may not be available.
•
1
Turn power on
for about 1 second
• Press
• Mains power On / Off switch should be On. (p. 9)
Enjoy selected internet content with VIERA Connect.
Simply press the OK / INTERNET button
2
Every time you turn on the TV, VIERA Connect introduction
banner appears. The banner is subject to change.
Access VIERA Connect
While the banner is displayed
Using “VIERA Connect”
or
Example :
button design varies
• The
depending on the remote
INTERNET
control.
on the usage conditions, it may take a
• Depending
while to read all the data.
might be displayed before VIERA Connect
• Messages
home screen.
Welcome to VIERA Connect™
VIERA Connect™ home screen is subject to change without notice.
The services through VIERA Connect™ are operated by their respective service providers, and service may
be discontinued either temporarily or permanently without notice. Therefore, Panasonic will make no
warranty for the content or the continuity of the services.
All features of websites or content of the service may not be available.
Please read these instructions carefully and follow the
on screen instructions.
Example : VIERA Connect home screen
To go to the next level
[MORE]
To back to the previous level
[BACK]
Don’t show this message again
ENTER
■ To exit from
Some content may be inappropriate for some viewers.
Some content may only be available for specific countries and may be presented in specific languages.
VIERA Connect
EXIT
set the VIERA
• ToConnect
instruction
•
•
banner display off
[VIERA Connect
Banner] (p. 36)
MORE
BACK
■ How to operate VIERA Connect (current as of January, 2011)
• To move the cursor / select the item
• When the key words are displayed on colour bar
(red)
(green)
(yellow)
(blue)
• To access
• To return to the previous screen
options with
• When
numbers are displayed
return to VIERA Connect home
• Toscreen
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
BACK/
RETURN
INTERNET
communication (ex. Skype™) requires an exclusive Communication Camera TY-CC10W.
• Video
“Optional accessories” (p. 6)
For details, read the manual of the Communication Camera.
can connect a keyboard and a gamepad via USB port for character input and playing games in VIERA Connect.
• You
You can also operate the TV with a keyboard or a gamepad other than VIERA Connect features. For more information
“USB connection” (p. 97)
Note
cannot access VIERA Connect, check the network connections (p. 11) and settings (p. 13 - 15).
• IfForyoumore
information of VIERA Connect (p. 79)
•
16
Watching TV
Turn power on
1
for about 1 second
• Press
power On / Off switch should be On.
• Mains
(p. 9)
■ VIERA Connect introduction banner appears
You can access to VIERA Connect and enjoy the various contents. (p. 16)
To remove this banner, leave for about 5 seconds or press any buttons
(except the buttons to access VIERA Connect).
To set this banner display off [VIERA Connect Banner] (p. 36)
•
•
Select the mode
2
selectable modes vary depending on the
• The
stored channels (p. 12).
TV
select
TV Selection
DVB-C
DVB-T
Analogue
access
panel of the TV. (p. 9)
Selection] menu is not displayed, press the
• IfTV[TVbutton
to switch the mode.
1
BBC ONE WALES
Volume
20:35
All DVB-T Channels
Change category
Coronation Street
20:00 - 20:55
Now
Info
Information banner
Select a channel
3
up
abc
or
down
def
ghi
jkl
mno
pqrs
tuv
wxyz
6
7
8
1
2
3
4
def
wxyz
select channel
Sorting 123...
Cartoon Nwk
BBC Radio Wales
BBC Radio Cymru
BBC ONE Wales
BBC THREE
BBCi
CBBC Channel
(p. 18)
select a more than two-digit channel position
• Tonumber,
e.g. 399
■ To select from the Channel List
All DVB-T Channels
Watching TV
possible to select the mode pressing the TV
• Also
button repeatedly on the remote control or side
watch
wxyz
sort channel names in
• Toalphabetical
order
(red)
• To change the category
(blue)
■ Select a channel using Information banner (p. 18)
1 Display Information banner if it is not displayed
2 While the banner is displayed, select the channel
select channel
watch
■ Select a channel using TV Guide (p. 21)
1 Display TV Guide 2 Select the current
3 Select [View] (DVB mode)
IDE
GU
programme or channel
select
access
Das Erste
19:30- 20:00
View
Timer Programming
select
watch
postcode entry or update may be required depending on the country you select (p. 12). Follow the on screen
• The
instructions.
Note
• To watch pay-TV
“Using Common Interface” (p. 49)
17
Other useful functions
Display Information banner
Display Information banner
Also appears when changing a channel
•
1
2
3
5
6
7
4
Example : DVB
HDTV
1
ZDF
Bad signal
20:35
All DVB-T Channels
Coronation Street
20:00 - 20:55
Now
Info
Dolby D+
Change category
45
1 Channel position and name
2 Channel type ([Radio], [Data], [HDTV], etc.) /
5 Programme Start / Finish time (DVB)
Encrypted channel (
TV mode ( , , )
3 Programme
4 Current time
6 Progress time indicator of the selected programme
)/
Channel number, etc. (Analogue)
(DVB)
7 Category
• To change the category (DVB)
select
(blue)
Watching TV
set
Features available / Message meanings
Teletext service available
Sound mute On
[Bad signal]
Poor TV signal quality
Multiple audio available
[Dolby D+], [Dolby D], [HE-AAC]
Dolby Digital Plus, Dolby Digital or
HE-AAC audio track
Multiple video available
Multiple audio and video available
[Stereo], [Mono]
Audio mode
1 - 90
Off Timer remaining time
For settings (p. 19)
•
Subtitle service available
confirm another tuned channel
• Toname
• To hide
watch the channel listed in the
• Tobanner
• Extra information (DVB)
EXIT
on the next programme
• Information
(DVB)
• To set display timeout
[Banner Display Timeout] (p. 36)
(Press again to hide the banner)
Display subtitles
Display / hide subtitles (if available)
To change the language for DVB (if available)
STTL
[Preferred Subtitles] (p. 35)
•
Note
press the STTL button in Analogue mode, it switches to teletext service and calls up a favourite page (p. 24). Press the
• IfEXITyoubutton
to return to TV mode.
18
Hold
Freeze / unfreeze picture
HOLD
Display the selectable settings for the current status
Check or change the current status instantly
To change
OPTION
•
select
select / change
access
store
[Multi Video] (DVB mode)
Allows you to select from a group of
multiple videos (if available)
This setting is not memorized and it
will return to the default setting once
you exit the current programme.
•
•
[Teletext Language] (DVB mode)
Allows you to select between alternative
language for teletext (if available)
[Sub Channel] (DVB mode)
Allows you to select the multifeed
programme - sub channel (if available)
[MPX] (Analogue mode)
Selects multiplex sound mode (if
available)
[Sound Menu] (p. 32)
[Subtitle Language] (DVB mode)
Allows you to select the language
in which subtitles should appear (if
available)
[Volume Correction]
Adjusts volume of individual channel or
input mode
[Teletext Character Set]
Sets the teletext language font
[Setup Menu] (p. 35)
[Safely remove USB]
Takes this operation to remove the
connected USB device safely from the TV
Watching TV
[Multi Audio] (DVB mode)
Allows you to select between
alternative language for sound tracks
(if available)
This setting is not memorized and it
will return to the default setting once
you exit the current programme.
[Dual Audio] (DVB mode)
Allows you to select stereo / monaural
(if available)
Off Timer
Turn the TV to Standby mode automatically after a fixed period
1 Display the menu
MENU
2 Select [Timer]
select
Main Menu
access
Picture
Sound
Timer
Setup
3 Select [Off Timer] and set the time
Timer Programming
Off Timer
Auto Standby
Off
15 minutes
30 minutes
45 minutes
60 minutes
75 minutes
90 minutes
select [Off Timer]
select the time
access
store
Set to [Off ] or turn the TV off.
• ToTo cancel
confirm the remaining time “Display Information banner” (p. 18)
• When
• screen.the remaining time is within 3 minutes, the remaining time will flash on the
19
Aspect
Change the aspect ratio (image size)
Enjoy viewing the image at its optimum size and aspect.
ASPECT
Programmes usually contain an “Aspect Control Signal” (Widescreen signal, etc.), and the TV will choose the aspect
ratio automatically according to the “Aspect Control Signal” (p. 92).
■ If you would like to change the aspect ratio manually
1 Display Aspect Selection list
2 While the list is displayed,
select the mode
ASPECT
Aspect Selection
Auto
16:9
14:9
Just
4:3
4:3 Full
Zoom1
Zoom2
Zoom3
Select
EXIT
Change
can also change the mode only
• You
using the ASPECT button.
select
ASPECT
store
(Press repeatedly until you reach
the desired mode)
RETURN
Aspect Selection list
[Auto]
The best ratio is chosen and the image expanded to fill the screen.
For details (p. 92)
Watching TV
[16:9]
[4:3 Full]
Directly displays the image at 16:9
without distortion (anamorphic).
[14:9]
Displays a 4:3 image enlarged
horizontally to fit the screen.
HD signal only
•
[Zoom1]
Displays the image at the standard 14:9
without distortion.
[Just]
Displays a 16:9 letterbox or 4:3 image
without distortion.
[Zoom2]
Displays a 4:3 image full-screen.
Stretching is only noticeable at the left
and right edges.
[4:3]
Displays a 16:9 letterbox (anamorphic)
image full-screen without distortion.
[Zoom3]
Displays the image at the standard 4:3
without distortion.
Displays a 2.35:1 letterbox (anamorphic)
image full-screen without distortion.
At 16:9, displays the image at its
maximum (with slight enlargement).
Note
is fixed to [16:9] when [Viewing Mode] is set to [Game] in the Picture Menu.
• Aspect
[16:9] and [4:3] are available in PC input mode.
• Only
available in teletext service.
• Not
• Aspect mode can be memorized separately for SD (Standard definition) and HD (High definition) signals.
Last view
Switch to previously viewed channel or input mode easily
Press again to return to the present view.
LAST VIEW
Note
•
channel is not available while the recording of Timer Programming, Direct TV Recording or One Touch Recording
• Switching
is in progress.
• Watching less than 10 seconds is not regarded as the previously viewed channel or input mode.
20
Using TV Guide
TV Guide - Electronic Programme Guide (EPG) provides an on screen listing of the programmes currently broadcast and the
forthcoming broadcasts over the next seven days (depending on the broadcasters).
This function varies depending on the country you select (p. 12).
The postcode entry or update may be required to use the GUIDE Plus+ system depending on the country you select.
“View advertisement” (p. 22)
DVB-T and Analogue channels are displayed on the same TV Guide screen. [D] means DVB-T channel and [A] means Analogue
channel. There will be no programme listings for Analogue channels.
When this TV is turned on for the first time, or the TV is switched off for more than a week, it may take some time before TV
Guide is completely shown.
•
•
•
•
1
Select the mode
(p. 17)
TV
2
View TV Guide
IDE
GU
again to change the layout ([Landscape] / [Portrait]).
• Press
View [Landscape] to see many channels.
View [Portrait] to see one channel at a time.
1
TV Guide: Landscape
Wed 27.10.2010
10:46
3
Time:
5
7
Wed 27.10.2010
All Types
All Channels
1 BBC ONE
20:00 - 20:30 DIY SOS : We open in the Battersbys
D
1 BBC ONE
D
7 BBC THREE
19:30
Das Erste
20:00
DIY SOS
Hot Wars
Holiday Program
10 O’ clock News BBC
D 70 BBC FOUR
D 72 BBC 2W
Panorama
D 105 BBCi
I’m A Celebrity
D 105 BBC Radi
Rugby
Select channel
EXIT
Select programme
Timer Programming
RETURN
-24 hours
+24 hours
21:00
Red Cap
Coronation Street
Emmerdal.
D 14 E4
20:30
The Bill
Pepsi Char.
Good bye
Pop Idol
News
Coast
15 To 1
GUIDE
Info
Change display mode
Select Advert
Prog.Type
The Bill
Page up
Page down
Category
TV Guide: Portrait
Wed 27.10.2010
All Types
D 1 BBC ONE
D
19:30-20:00
Das Erste
■ To return to TV
EXIT
7 BBC THREE
20:00-20:30
DIY SOS
20:30-21:00
The Bill
21:00-22:00
Red Cap
22:00-23:00
Live junction
23:00-23:30
POP 100
23:30-00:00
Rugby
Select programme
EXIT
Select channel
Timer Programming
RETURN
+24 hours
6
1
2
3
4
5
6
Current date and time
TV Guide date
TV Guide time
Programme
Advertisement
Channel position and
name
7 [D] : DVB-T
[A] : Analogue
Depending on the country
you select, you can select the
TV Guide type
Example :
[Portrait] (Displays by time)
Wed 27.10.2010
10:46
4
The Bill
Spring watch
OPTION
2
Using TV Guide
Example :
[Landscape] (Displays by channel)
GUIDE
OPTION
D 14 E4
Info
Change display mode
Select Advert
Prog.Type
All Channels
D 70 BBC FOUR
[Default Guide] in [Display
Settings] (p. 35)
If you select [Channel List], the
channel list will appear when
the GUIDE button is pressed.
Page up
Page down
Category
■ To watch the programme
1 Select the current programme or
2 Select [View] (DVB mode)
channel
select
Das Erste
19:30- 20:00
access
View
Timer Programming
select
watch
• To use Timer Programming
(p. 23)
21
■ To the previous day (DVB mode)
■ To the next day (DVB mode)
(red)
(green)
■ To view a channel list of the selected type
■ To view a channel list of the selected category
(DVB mode)
(blue)
(yellow)
(Category list)
(Type list)
Prog.Type
All Types
Categor y
All Channels
select type
view
All Channels
All DVB -T Channels
All Analogue Channels
Free T V
Pay T V
HDT V
Free Radio
Pay Radio
Favourites1
Favourites2
Favourites3
Favourites4
All Types
Movie
News
select category
view
Only Analogue channels are listed
• To list favourite channels
(p. 39)
Using TV Guide
Other useful functions
View details of the programme (DVB mode)
1 Select the programme
select
2 View details
• Press again to return to TV Guide.
View advertisement
Depending on the country you select, this TV supports the GUIDE Plus+ system in DVB-T or Analogue mode
The postcode entry or update is required. Follow the on screen instructions.
Also possible to setup manually from the Setup Menu
[Update] / [Postcode] in [GUIDE Plus+ Settings] (p. 36)
Enter your postcode when using this function for the first time. If you enter an incorrect postcode for your area, or no
postcode is entered, advertisements may not be displayed correctly.
•
•
Display advertisement information
To display the latest advertisement
[Update] in [GUIDE Plus+ Settings] (p. 36)
OPTION
•
■ To change advertisements
■ To return to TV Guide
BACK/
RETURN
OPTION
or
Note
• To update the information continuously, the TV must be left in Standby mode.
22
Timer Programming (DVB mode)
Timer Programming is a timer to remind watching or record the programme to the external recorder or the USB HDD.
1 Select the forthcoming programme
2 Select the function ([Ext Rec.], [USB HDD Rec.] or [Reminder])
select
(Timer Programming screen)
Timer Programming
Function
set
Ext Rec.
---
LED will turn to orange if
Timer Programming is set.
(Orange LED will flash if the recording of
Timer Programming is in progress.)
No.
D
12
BBC ONE
<TIMER>
Date
Start
End
Wed 27.10.2010
20:00 20:30
(30 min.)
--/--
--:---:-(--- min.)
---
---
---
--/--
--:---:-(--- min.)
---
---
--/--
--:---:-(--- min.)
--/--
--:---:-(--- min.)
---
Edit timer
select
Wed 27.10.2010 10:46
Channel Name
--Select timer
EXIT
0
500GB (50%)
RETURN
9
Info
store
1/1
Page up
Page down
Delete
LED
■ To check / change / cancel a timer
programming event
“Timer Programming” (p. 44 - 46)
■ To return to TV Guide
BACK/
RETURN
■ If you select the current programme
Using TV Guide
[Ext Rec.] / [USB HDD Rec.] :
to record the programme to the external recorder or the USB HDD
When the start time comes, the channel will be switched automatically and the
video and audio signals will be output. 2 minutes before the starting time, a
reminder message appears if you are watching TV.
[Reminder] :
to remind you to watch the programme
When you are watching TV, a reminder message appears 2 minutes before the
start time. Press the OK button to switch to the programmed channel.
A confirmation screen asking whether you wish to watch or record the programme will appear.
Select [Timer Programming] and set [Ext Rec.] or [USB HDD Rec.] to record from the time you finish the timer programming
event setting.
Das Erste
19:30- 20:00
View
Timer Programming
select
access
Note
function is not available in Analogue mode.
• This
Programming only works reliably if correct time information is received via the signal from the broadcaster or service
• Timer
provider.
other channel can be selected while the recording of Timer Programming is in progress.
• No
recording programmes to the external recorder, be sure to make the proper settings on the recorder connected to the
• When
TV.
•
If a compatible recorder with Q-Link, VIERA Link or similar technologies is connected to the TV (p. 82, 83) and the [Link
Settings] (p. 34) are completed, no setting of the recorder is required. Also read the manual of the recorder.
When recording programmes to the USB HDD, be sure to format the USB HDD and enable it for recording in [Recording
Setup] (p. 53).
23
Viewing Teletext
Teletext services are the text information provided by the broadcasters.
The features may vary depending on the broadcasters.
What is FLOF (FASTEXT) mode?
In FLOF mode, four differently coloured subjects are situated at the bottom of the screen. To access more information about
one of these subjects, press the appropriately coloured button. This facility enables fast access to information on the subjects
shown.
What is TOP mode? (in case of TOP text broadcasting)
TOP is a particular improvement of the standard teletext service that results in an easier search and effective guide.
Fast overview of the teletext information available
Easy to use step-by-step selection of the topical subject
Page status information at the bottom of the screen
Available page up / down
To select among subject blocks
To select next subject within the subject
block
(red)
(green)
(blue)
(After the last subject, it moves to the next
subject block.)
•
•
•
Viewing Teletext
(yellow)
What is List mode?
In List mode, four differently coloured page numbers are situated at the bottom of the screen. Each of these numbers can be
altered and stored in the TV’s memory. “Store frequently viewed pages” (p. 25)
■ To change mode
[Teletext] (p. 35)
Switch to Teletext
1
the index page (content varies
• Displays
depending on the broadcasters)
TEXT
Sub page number
<< 01 02 03 04 05 06 07
>>
17:51 28 Feb
Time / date
TELETEXT
INFORMATION
Colour bar
Current page number
Select the page
2
abc
up
def
ghi
jkl
mno
pqrs
tuv
wxyz
or
or
down
Coloured button
(Corresponds to the colour bar)
■ To adjust contrast
EXIT
(Press three times)
Reveal hidden data
INDEX
Reveal hidden words e.g. quiz page answers
Press again to rehide.
MENU
(red)
•
HOLD
Stop automatic updating
(If you wish to hold the current page without updating)
HOLD Press again to resume.
•
24
As the blue bar is displayed
MENU
■ To return to TV
Return to the main index page
INDEX
Call up a favourite page
View a favourite page stored
Call up the page stored on the blue button (List mode).
Factory setting is “P103”.
STTL
•
FULL / TOP / BOTTOM
MENU
(green)
(TOP)
(BOTTOM)
Normal (FULL)
(Expand the TOP half )
(Expand the BOTTOM half )
View in multi window
Watch TV and Teletext in two windows at once
MENU
Select Picture and text On or Off
(Press twice)
• Operations can be made only in teletext screen.
Store frequently viewed pages
press and hold
(Corresponding
coloured button)
The number changes to white.
Viewing Teletext
Store frequently viewed pages in the colour bar (List mode only)
As page is displayed
■ To change stored pages
Enter new page number
Coloured button you
want to change
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
press and hold
View sub page
View sub page (Only when Teletext is more than one page)
Appears at top of the screen
number of sub pages varies depending on the
• The
broadcasters (up to 79 pages).
some time for searching, during which time
• Ityoumaycantake
watch TV.
■ To view specific sub page
MENU
Enter the 4-digit number
Example : P6
(blue)
mno
Watch TV while waiting for update
View the TV picture while searching for a teletext page
Teletext automatically updates itself when new information becomes available.
Changes to TV screen temporarily
MENU
(yellow)
P108
Appears when updating
is completed
View the updated
page
(yellow)
(You cannot change the channel.)
• The news page provides a function that indicates arrival of latest news (“News Flash”).
25
Watching External Inputs
Connect the external equipment (VCRs, DVD equipment, etc.) and you can watch through the input.
To connect the equipment (p. 10, 11, 89, 90)
The remote control is capable of operating some functions of selected external equipment.
“Operating the equipment with the TV remote control” (p. 27)
•
1
Turn the TV on
When connecting with SCART as example 2 or 3 (p. 10, 11)
Receives input signals automatically when playback starts
Input signals are automatically identified by the SCART (pin 8) terminal.
This function is also available for HDMI connections (p. 89).
•
•
If input mode is not switched automatically
Perform 2 and 3
Check the setup of the equipment.
•
Watching External Inputs
2
Display the input selection menu
3
Select the input mode connected to the equipment
AV
Input Selection
AV1
AV2
COMPONENT
PC
HDMI1
HDMI2
HDMI3
HDMI4
TV
SD Card/USB
select
watch
can also select the input using the AV button on the remote control or the side
• You
panel of the TV (except [SD Card/USB]).
Press the button repeatedly until the desired input is selected.
Card/USB] : Switches to Media Player “Using Media Player” (p. 57)
• [SD
You can label or skip each input mode (except [SD Card/USB]). “Input Labels” (p. 48)
• Skipped
inputs will not be displayed when the AV button is pressed.
TV
■ To return to TV
TV
4
View
AV1
Displays the selected mode
Note
external equipment has an aspect adjustment function, set it to “16:9”.
• IfForthedetails,
see the manual of the equipment or ask your local dealer.
•
26
Operating the equipment with the TV remote control
The equipment connected to the TV can be directly operated with the below buttons of this TV remote control.
DVD/VCR
TV
Selection Switch for operating the connected equipment
Select “DVD/VCR” to operate Panasonic DVD Recorder, DVD Player, Player theatre, Blu-ray Disc
theatre or VCR
“How to change the code for the type of the equipment” (see below)
Select “TV” to use USB HDD Recording, Media Player or VIERA Link
“USB HDD Recording” (p. 55)
“Media Player” (p. 64)
“VIERA Link Control” (p. 86)
Standby
Set to Standby mode / Turn on
Play
Playback videocassette / DVD / video content
Stop
Stop the operations
Watching External Inputs
Rewind / Skip / Search
VCR :
Rewind, view the picture rapidly in reverse
DVD / video content :
Skip to the previous track, title or chapter
Press and hold to search backward
Fast-forward / Skip / Search
VCR :
Fast-forward, view the picture rapidly forward
DVD / video content :
Skip to the next track, title or chapter
Press and hold to search forward
Pause
Pause / Resume
DVD : Press and hold to play at slow speed
PROGRAMME
REC
Channel Up / Down
Select channel
Record
Start recording
How to change the code for the type of the equipment
Each type of the Panasonic equipment has its own remote control code.
Please change the code according to the equipment you want to operate.
1 Set the position to “DVD/VCR”
DVD/VCR
TV
2 Press and hold
during the following operations
Enter the appropriate code, see
Press
table below
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
Type of the equipment
Code
DVD Recorder, DVD Player, Blu-ray Disc Player
70 (default)
Player theatre, Blu-ray Disc theatre
71
VCR
72
Note
if the remote control works correctly after changing the code.
• Confirm
codes may be reset to default values if batteries are replaced.
• The
• Some operations may not be possible on some equipment models.
27
How to Use VIERA TOOLS
You can access some special features easily by using the VIERA TOOLS function.
1
Display icons of the feature
2
Select a feature
TO
VIERA OLS
select
access
■ To return to TV
EXIT
VIERA Link Control
or
TO
VIERA OLS
How to Use VIERA TOOLS
■ Follow the operations of each feature
[VIERA Link Control]
“VIERA Link Control” (p. 86)
When two or more compatible equipment are
connected, a selection screen will be displayed.
Please select the correct description and access.
[Music]∗
“Music mode” (p. 67)
[Photo]∗
“Photo mode” (p. 59)
[VIERA Connect]
“VIERA Connect” (p. 79)
[Video]∗
“Video mode” (p. 63)
[Media Server]∗
“Using DLNA® features” (p. 76)
[Recorded TV]∗
“Recorded TV mode” (p. 64)
∗ When two or more available devices are connected, a selection screen will be displayed.
Please select the correct description and access.
Note
the selected feature is not available, the demonstration to explain how to use it can be displayed. Press the OK button to
• Ifview
the demonstration after selecting the unavailable feature.
28
How to Use Menu Functions
Various menus allow you to make settings for the picture, sound, and other functions.
Display the menu
1
• Displays the functions that can be set (varies according to the input signal)
MENU
Select the menu
2
Example : [Picture Menu]
select
Main Menu
access
Picture
Sound
Timer
Setup
How to Use Menu Functions
Select the item
3
Example : [Picture Menu]
Viewing Mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour Balance
Vivid Colour
Eco Mode
1/2
select
60
0
30
5
0
access
Dynamic
Warm
Off
Off
■ Choose from among alternatives
TV
■ To return to TV at any
store
■ Adjust using the slide bar
Sharpness
5
time
EXIT
select
Cool
Normal
Warm
Colour Balance
change
store
Moved
■ Go to the next screen
Child Lock
■ To return to the
previous screen
BACK/
RETURN
Access
Displays the next screen
access
■ Enter characters by free input menu
You can enter names or numbers freely for some items.
Set characters one by one
User input
Name
select
■ To change menu
pages
up
down
A
B
C D
E
F
G H
I
J
K
L M N O
P
Q
R
S
T
U
V W X
Y
Z
0
1
2
3
4
5
6
7
8
9
!
:
#
a
b
c
d
e
f
g
h
i
j
k
l
m n
o
p
q
r
s
t
u
v
w
x
y
z
(
)
+
-
.
*
_
Store
BACK/
RETURN
set
can set characters by using numeric buttons.
• You “Characters
table for numeric buttons” (p. 97)
■ To reset the settings
reset the picture settings only
• To [Reset
to Defaults] in the Picture Menu (p. 31)
reset the sound settings only
• To [Reset
to Defaults] in the Sound Menu (p. 33)
initialise all settings
• To [Shipping
Condition] in the Setup Menu (p. 36)
29
Menu list
Menu
Item
Adjustments / Configurations (alternatives)
Basic picture mode
[Dynamic] / [Normal] / [Cinema] / [True Cinema] / [Game] / [Photo]
In each Viewing Mode and input, [Contrast], [Brightness], [Colour], [Sharpness], [Tint],
[Colour Balance], [Vivid Colour], [Eco Mode], [P-NR] and [3D-COMB] can be adjusted
and stored to suit your particular viewing requirement.
Set for each input signal.
[Dynamic] :
Provides enhanced picture contrast and sharpness when viewing in a bright room.
[Normal] :
Recommended for viewing under normal ambient room lighting conditions.
[Cinema] :
For watching movies in a darkened room with the improved performance of contrast,
black and colour reproduction
[True Cinema] :
Precisely reproduces the original quality of the image without any revision.
[Game] :
Fast response signal specifically to provide suitable images for playing games
Not valid on TV mode
A continuous record of time spent using Game mode can be displayed in the top
right of the screen. [Playing Time Display] (p. 36)
[Photo] :
Set [Reversal Film Effect] to [On] to provide the suitable image quality for photos
For HDMI input, Media Player and network service operations
•
Viewing Mode
•
•
Picture
How to Use Menu Functions
•
Contrast, Brightness,
Colour, Sharpness
Increases or decreases the levels of these options according to your personal
preference
Tint
With an NTSC signal source connected to the TV, the picture hue can be adjusted to
suit your taste
For NTSC signal reception only
•
Allows you to set the overall colour tone of the picture [Cool] / [Normal] / [Warm]
Colour Balance
• Not valid when [Viewing Mode] is set to [True Cinema].
Vivid Colour
• Not valid on PC signal
Automatically adjusts colours to vivid ones [Off] / [On]
Reversal Film Effect
Provides the picture effect such as the reversal film [Off] / [On]
This function is available when [Viewing Mode] is set to [Photo].
Eco Mode
Automatic Brightness Control function
Adjusts picture settings automatically dependent on ambient lighting conditions
[Off] / [On]
P-NR
Picture Noise Reduction
Automatically reduces unwanted picture noise and flicker noise in the contoured parts
of a picture [Off] / [Min] / [Mid] / [Max]
Not valid on PC signal
3D-COMB
Makes still or slow moving pictures look more vivid [Off] / [On]
Occasionally, whilst viewing still or slow moving pictures, colour patterning may be
seen. Set to [On] to display sharper and more accurate colours.
For PAL or NTSC signal reception only
Not valid on RGB, Component, PC, HDMI and Media Player
Screen Display
Turns the screen off when you select [Off ]
[Off] / [On]
The sound is active even if the screen turns off.
Press any buttons (except Standby) to turn the screen on.
This function is effective in reducing power consumption when listening to the sound
without watching the TV screen.
•
•
30
•
•
•
•
•
•
Menu
Item
Adjustments / Configurations (alternatives)
White Balance
R-Gain
Adjusts the white balance of bright red area
G-Gain
Adjusts the white balance of bright green area
B-Gain
Adjusts the white balance of bright blue area
R-Cutoff
Adjusts the white balance of dark red area
G-Cutoff
Adjusts the white balance of dark green area
B-Cutoff
Adjusts the white balance of dark blue area
Reset to
Defaults
Press the OK button to reset to the default White Balance
Gamma
Gamma
Reset to
Defaults
Picture
Advanced Settings
24p Smooth Film
Film Cadence
Detection
Press the OK button to reset to the default Gamma
Automatically compensates the picture frame rate and removes juddering movements
to make the images smooth [Off] / [Mid] / [Max]
Depending on the contents, images may be noisy. To prevent the noise, change the
setting.
This function is not available for selection (default to [Off ]) when [Viewing Mode] is
set to [Game] or in the mode of PC input, photo or network service operations.
•
•
Automatically compensates the picture frame rate to make the 24p source movie
images smooth [Off] / [Mid] / [Max]
This is available only for 24p signal input and displayed instead of [Intelligent Frame
Creation].
This function is not available for selection (default to [Off ]) when [Viewing Mode] is
set to [Game] or in the mode of PC input, photo or network service operations.
•
•
Automatically makes the film source movie images clear [Off] / [On]
How to Use Menu Functions
Intelligent Frame
Creation
Switches the gamma curve [1.8] / [2.0] / [2.2] / [2.4] / [2.6]
• Please note the numerical values are reference for the adjustment.
Enhances the picture resolution to make the image sharper [Off] / [Mid] / [Max]
Resolution Enhancer
function is available for SD (Standard definition) signal.
• This
for HD (High definition) signal, this function is available when aspect mode is set
• Asto [16:9]
([16:9 Overscan] is set to [On]), [4:3 Full] or [Zoom].
• Not valid on VIERA Connect and Media Player
16:9 Overscan
Selects the screen area displaying the image [Off] / [On]
[On] :
Enlarged the image to hide the edge of the image.
[Off] :
Displayed the image in the original size.
Set to [On] if noise is generated on the edge of the screen.
This function is available when aspect is set to [Auto] (16:9 signal only) or [16:9].
This function can be memorized separately for SD (Standard definition) and HD (High
definition) signals.
AV Colour System
Selects optional colour system based on video signals in AV mode
[Auto] / [PAL] / [SECAM] / [M.NTSC] / [NTSC]
DVI Input Setting
Changes the black level in the image for HDMI input mode with DVI input signal
manually [Normal] / [Full]
When the DVI input signal from the external equipment, especially from PC, is
displayed, the black level may not be suitable. In this case, select [Full].
The black level for HDMI input signal will be adjusted automatically.
For HDMI input mode with DVI input signal only
Reset to Defaults
•
•
•
•
•
•
Press the OK button to reset the present Picture Viewing Mode of the selected input to
the default settings
31
Menu
Item
Adjustments / Configurations (alternatives)
Selects the basic sound mode [Music] / [Speech] / [User]
The selected mode affects all input signals.
[Music] :
Improves sound quality for watching music videos, etc.
[Speech] :
Improves sound quality for watching news, drama, etc.
In Music and Speech modes, you can adjust [Bass] and [Treble] settings, and those
settings will be stored for each mode.
[User] :
Adjusts the sounds manually by using the equaliser to suit your favourite sound
quality.
For the User mode, [Equaliser] will appear on the Sound Menu instead of [Bass] and
[Treble]. Select the [Equaliser] and adjust the frequency. [Equaliser] (see below)
•
Mode
•
•
Sound
How to Use Menu Functions
Bass
Increases or decreases level to enhance or minimise lower, deeper sound output
Treble
Increases or decreases level to enhance or minimise sharper, higher sound output
Equaliser
Adjusts the frequency level to suit your favourite sound quality
This function is available when [Mode] is set to [User].
Select the frequency and change the frequency level by using the cursor button.
If you want to enhance the bass sound, raise the level of the lower frequency. If you
want to enhance the treble sound, raise the level of the higher frequency.
To reset the levels of each frequency to the default settings, select the [Reset to
Defaults] by using the cursor button, and then press the OK button.
Balance
Adjusts volume level of right and left speakers
Headphone Volume
Adjusts the volume of the headphones
Surround
Surround sound settings [Off] / [V-Audio] / [V-Audio Surround]
[V-Audio] :
Provides a dynamic enhancer of width to simulate improved spatial effects
[V-Audio Surround] :
Provides a dynamic enhancer of width and depth to simulate improved spatial effects
Auto Gain Control
Adjusts the current volume level if it is extremely different from the previous viewed
channel or input mode [Off] / [On]
Volume Correction
Adjusts the volume of individual channel or input mode
Speaker Distance to Wall
the back space between the TV and wall is over 30 cm, [Over 30cm] is
• Ifrecommended.
the back space between the TV and wall is within 30 cm, [Up to 30cm] is
• Ifrecommended.
MPX
Selects multiplex sound mode (if available)
[Stereo] : Use this normally
[Mono] : When stereo signal cannot be received
[M1] / [M2] : Available while mono signal is transmitted
Analogue mode only
•
•
•
•
Adjusts the low frequency sound [Over 30cm] / [Up to 30cm]
•
32
Menu
Item
Adjustments / Configurations (alternatives)
Selects the initial setting for audio tracks [Auto] / [Multichannel] / [Stereo] / [MPEG]
Selectable options vary depending on the country you select.
[Auto] : Automatically selects the audio tracks if programme has more than two tracks.
The priority is given in the following order - Dolby Digital Plus, HE-AAC, Dolby
Digital, MPEG.
[Multichannel] : The priority is given to multi-channel audio track.
[Stereo] : The priority is given to stereo (2ch) audio track.
[MPEG] : The priority is given to MPEG.
Dolby Digital Plus and Dolby Digital are the methods of coding digital signals
developed by Dolby Laboratories. Apart from stereo (2ch) audio, these signals can be
multi-channel audio.
HE-AAC is a perceptual coding method used to compress digital audio for efficient
storage and transmission.
MPEG is an audio compression method that compresses audio to the smaller size
without any considerable loss of audio quality.
Dolby Digital Plus and HE-AAC are the technologies for HD (High definition)
programmes.
DVB mode only
•
Audio Preference
•
•
•
•
•
•
•
HDMI1 / 2 / 3 / 4 Input
Select to fit the input signal [Digital] / [Analogue] (p. 96)
[Digital] : HDMI cable connection
[Analogue] : HDMI-DVI adaptor cable connection
HDMI input mode only
•
Adjusts the delay time of the sound output from DIGITAL AUDIO OUT terminal if the
sound does not synchronize the image
DVB mode only
Reset to Defaults
Press the OK button to reset the present Sound Mode, [Balance], [Headphone Volume]
and [Surround] to the default settings
Timer Programming
Sets a timer to remind watching or record forthcoming programmes (p. 44)
DVB mode only
Off Timer
Sets the time until the TV automatically goes to Standby mode
[Off] / [15] / [30] / [45] / [60] / [75] / [90] (minutes) (p. 19)
Auto Standby
Sets the time the TV automatically goes to Standby mode when no operation is
performed for the selected times [Off] / [2] / [4] (hours)
Starting Timer Programming automatically does not affect this function.
Automatic input switching with the connected equipment affects this function and
time-count will be reset.
The notification message will appear 3 minutes before going to Standby mode.
Timer
SPDIF Delay
How to Use Menu Functions
Sound
SPDIF Selection
SPDIF : A standard audio transfer file format
Selects the initial setting for digital audio output signal from DIGITAL AUDIO OUT and
HDMI2 (ARC function) terminals [Auto] / [PCM]
[Auto] : Dolby Digital Plus, Dolby Digital and HE-AAC (48 kHz) multi-channel are output
as Dolby Digital Bitstream.
MPEG is output as PCM.
[PCM] : Digital output signal is fixed to PCM.
For DVB mode, network video contents (p. 77) or Video mode of Media Player (p. 63)
ARC (Audio Return Channel) : A function of digital audio output using HDMI cable
•
•
•
•
•
33
Menu
Item
Adjustments / Configurations (alternatives)
Eco Navigation
Automatically sets the TV to the most suitable energy-saving mode
If you press the OK button, the following items are set as below :
[Eco Mode], [VIERA Link], [Power off Link], [Standby Power Save], [Power Save]
[Intelligent Auto Standby] [On (No reminder)]
[Auto Standby] [2 hours]
Recording Setup
Formats the connected USB HDD and sets the condition (p. 53)
•
VIERA Link
Sets to use VIERA Link functions [Off] / [On] (p. 83)
HDMI Content Type
Adjusts the picture settings according to the content type signal from the connected
equipment via HDMI cable [Off] / [Auto]
This function is available if the connected equipment supports HDMI Content Type.
The content type information will be displayed for several seconds when this function
works.
AV1 out
•
•
Chooses the signal to be transmitted from the TV to Q-Link [TV] / [AV2] / [Monitor]
[Monitor] : Image displayed on screen
Component, PC HDMI signals cannot be output.
•
Link Settings
Setup
How to Use Menu Functions
Power on Link
Sets to use Power on Link function [Off] / [On] (p. 82, 83)
Power off Link
Sets to use Power off Link function [Off] / [On] (p. 82, 83)
Standby Power Save
Controls the power consumption in Standby mode of the connected equipment to
reduce the consumption [Off] / [On] (p. 84)
This function is available when [VIERA Link] is set to [On] and [Power off Link] is set
to [On].
Intelligent Auto
Standby
Download
Child Lock
•
Makes non-watched or non-used connected equipment go into Standby mode to
reduce the power consumption
[Off] / [On (With reminder)] / [On (No reminder)] (p. 84)
This function is available when [VIERA Link] is set to [On].
•
Downloads channel, language, country / region settings to a Q-Link or VIERA Link
compatible equipment connected to the TV
DVB-C channel settings cannot be downloaded.
•
Locks a channel / AV input to prevent access to it (p. 46)
DVB-C Tuning Menu
Favourites Edit
Creates list of favourite DVB-C channels (p. 39)
Channel List
Skips the unwanted DVB-C channels or edits DVB-C channels (p. 40)
Auto Setup
Automatically sets the DVB-C channels supplied (p. 37)
Manual Tuning
Sets the DVB-C channels manually (p. 41)
Update Channel List
Updates DVB-C Channel List while keeping your settings (p. 41)
Favourite Network
Selects your favourite network for each broadcasters (only available in some countries)
New Channel
Message
Selects whether to give a notification message when a new DVB-C channel is found
[Off] / [On] (p. 41)
Signal Condition
Checks the DVB-C signal condition (p. 41)
Attenuator
Automatically reduces the DVB-C signal to avoid the interference [Off] / [On] (p. 41)
Adds the TV mode
Add TV Signal
34
[On]
function is available if you skip any modes to tune in [Auto Setup] for first using
• This
the TV.
• To operate, refer to the “Auto Setup” operations for first using the TV (p. 12, 13).
Menu
Item
Adjustments / Configurations (alternatives)
DVB-T Tuning Menu
Favourites Edit
Creates list of favourite DVB-T channels (p. 39)
Channel List
Skips the unwanted DVB-T channels or edits DVB-T channels (p. 40)
Auto Setup
Automatically sets the DVB-T channels received in the area (p. 38)
Manual Tuning
Sets the DVB-T channels manually (p. 41)
Update Channel List
Updates DVB-T Channel List while keeping your settings (p. 41)
Favourite Network
Selects your favourite network for each broadcasters (only available in some countries)
New Channel
Message
Selects whether to give a notification message when a new DVB-T channel is found
[Off] / [On] (p. 41)
Signal Condition
Checks the DVB-T signal condition (p. 41)
Adds the TV mode
Add TV Signal
Setup
Analogue Tuning Menu
Channel List
Skips the unwanted Analogue channels or edits Analogue channels (p. 42)
Auto Setup
Automatically sets the Analogue channels received in the area (p. 38)
Manual Tuning
Sets the Analogue channels manually (p. 43)
Adds the TV mode
Add TV Signal
function is available if you skip any modes to tune in [Auto Setup] for first using
• This
the TV.
• To operate, refer to the “Auto Setup” operations for first using the TV (p. 12, 13).
Language
OSD Language
Changes language for on screen displays
Preferred Audio 1 / 2
Selects the first and second preferred language for DVB multi audio (depending on the
broadcaster)
Preferred Subtitles
1/2
Selects the first and second preferred language for DVB subtitles (depending on the
broadcaster)
To display subtitles (p. 18)
Preferred Teletext
How to Use Menu Functions
function is available if you skip any modes to tune in [Auto Setup] for first using
• This
the TV.
• To operate, refer to the “Auto Setup” operations for first using the TV (p. 12, 13).
•
Selects the preferred language for DVB teletext service (depending on the broadcaster)
Selects the preferred subtitle type [Standard] / [Hard of Hearing]
Preferred Subtitle
Type
of Hearing] provides aids in understanding and enjoyment with DVB subtitles
• [Hard
(depending on the broadcaster).
• [Preferred Subtitles 1 / 2] in [Language] are given priority.
Display Settings
Teletext
Teletext display mode [TOP (FLOF)] / [List] (p. 24)
Teletext Character
Set
Selects teletext language font [West] / [East1] / [East2]
[West] : English, French, German, Greek, Italian, Spanish, Swedish, Turkish, etc.
[East1] : Czech, English, Estonian, Lettish, Rumanian, Russian, Ukrainian, etc.
[East2] : Czech, Hungarian, Lettish, Polish, Rumanian, etc.
Default Guide
Selects the default TV Guide type when the GUIDE button is pressed (only available in
some countries) [TV Guide] / [Channel List]
[TV Guide] :
Electronic Programme Guide (EPG) is available.
To use EPG (p. 21)
[Channel List] :
EPG is not available and the channel list will appear instead of it.
•
35
Menu
Item
Adjustments / Configurations (alternatives)
Display Settings
Input Labels
Labels or skips each input terminal (p. 48)
Banner Display
Timeout
Sets how long the Information banner (p. 18) stays on screen
[0 (No display)] / [1] / [2] / [3] / [4] / [5] / [6] / [7] / [8] / [9] / [10] (seconds)
VIERA Connect
Banner
Sets the VIERA Connect introduction banner display [Off] / [On] (p. 16, 17)
Playing Time Display
Set to [On] to display a continuous record of time spent using Game mode every 30
minutes [Off] / [On]
This function is available when [Game] is selected in [Viewing Mode] (p. 30)
Radio Mode
•
Sets the timer for turning off the screen automatically when a radio channel is selected
[Off] / [5] / [10] / [15] / [20] (seconds)
The sound is active even if the screen turns off.
Press any buttons except Standby, Volume Up / Down and Sound Mute buttons to
turn the screen on.
This function is effective in reducing power consumption when listening to a radio
channel.
DVB mode only
•
•
•
•
Uses include to watch encrypted channels (p. 49)
Network Setup
Sets the network setting to use in your network environment (p. 71)
DivX® VOD
Displays DivX VOD registration code (p. 94)
System Menu
Setup
How to Use Menu Functions
Common Interface
USB Keyboard
Layout
• For the information of using USB Keyboard
Selects the language that your USB Keyboard supports
(p. 97)
Shipping Condition
Resets all settings, for example, when moving house (p. 50)
System Update
Downloads new software to this TV (p. 51)
Software Licence
Displays the software licence information
System Information
Displays the system information of this TV
GUIDE Plus+
Settings
Update
Performs the update of the GUIDE Plus+ schedule and advertising information for the
GUIDE Plus+ system (p. 22)
Postcode
Sets your postcode to display advertisements in the GUIDE Plus+ system (p. 22)
System
Information
Displays the system information of the GUIDE Plus+ system
Other Settings
Power on Preference
Automatically selects the input when the TV is turned on [TV] / [AV]
Set to [TV] to view picture from TV tuner.
Set to [AV] to view input from an external equipment connected to the AV1 or HDMI1
terminal, e.g. set top box.
The external equipment must be switched on and sending a control signal for
automatic switching at power on to occur.
•
Power Save
Reduces brightness of picture to economise on power consumption [Off] / [On]
Adjusts the time data
Time Zone
time data will be corrected based on GMT.
• The
• Set to [Auto] to adjust the time automatically according to your area.
different menu will be displayed in the mode of PC input, Media Player or network service operations. (p. 52, 58 - 68,
• A76 - 79)
• Only available items can be selected.
36
Retuning from Setup Menu
Automatically retune the channels received in the area.
This function is available if channel tuning is already performed.
Only the selected mode is retuned. All the previous tuning settings are erased.
If Child Lock PIN number (p. 47) has been set, the PIN number is required.
If tuning has not been done completely [Manual Tuning] (p. 41, 43)
•
•
•
•
DVB-C channels
1
Select DVB-C
(p. 17)
TV
2
3
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
4
■ To return to TV
Select [DVB-C Tuning Menu]
select
DVB-C Tuning Menu
EXIT
Access
5
Select [Auto Setup]
Auto Setup
For Auto Setup, using
the buttons on the side
panel of the TV (p. 9)
F
1 Press repeatedly
until [Auto Setup]
appears
2 Access [Auto Setup] TV
6
(select the item)
•
AV
(set)
DVB-C Auto Setup Settings
(store)
4 Start [Auto Setup]
Free Channels
Quick
Auto
Auto
Auto
Start scan
select
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
access / store
• After settings, select [Start scan].
• [Scan Mode]
and scan mode
TV
access
Access
Set the Auto Setup settings
Search Mode
Scan Mode
Frequency
Symbol Rate
Network ID
3 Set the search mode
select
DVB-C Tuning Menu
Retuning from Setup Menu
access
TV
F
7
[Full] : scans the whole frequency range
[Quick] : scans the suitable frequency in your country
Normally set [Frequency], [Symbol Rate] and [Network ID] to [Auto].
If [Auto] is not displayed or if necessary, enter [Frequency], [Symbol Rate] and [Network
ID] specified by your cable provider with numeric buttons.
Start Auto Setup (Settings are made automatically)
DVB-C Auto Setup
All DVB-C tuning data will be erased
When the operation is completed, the
channel at the lowest position will be
displayed.
TV
• To return to TV
AV
F
37
DVB-T or Analogue channels
1
Select DVB-T or Analogue
(p. 17)
TV
2
3
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
4
Select [DVB-T Tuning Menu] or [Analogue Tuning
Menu]
select
DVB-T Tuning Menu
Analogue Tuning Menu
■ To return to TV
Access
Access
EXIT
5
Retuning from Setup Menu
Example :
Auto Setup
select
Access
DVB-T :
All DVB-T tuning data will be erased
3 Start [Auto Setup]
access
Start Auto Setup (Settings are made automatically)
DVB-T Auto Setup
For Auto Setup, using
the buttons on the side
panel of the TV (p. 9)
F
1 Press repeatedly
until [Auto Setup]
appears
2 Access [Auto Setup] TV
•
Select [Auto Setup]
DVB-T Tuning Menu
6
access
The displayed item depends on the selected
mode.
DVB-T Auto Setup
CH 5
Progress
This will take about 3 minutes.
CH
Channel Name
CBBC Channel
62
BBC Radio Wales
62
E4
62
62
Cartoon Nwk
Free TV: 4
69
Type
Free TV
Free TV
Free TV
Free TV
Pay TV: 0
Searching
Radio: 0
Analogue :
Analogue Auto Setup
All analogue tuning data will be erased
Analogue Auto Setup
Scan
This will take about 3 minutes.
CH
CH 29
CH 33 BBC1
CH 2
78 CC 1
Channel Name
TV
Analogue: 2
Searching
F
TV
• To return to TV
38
AV
F
Quality
100
100
100
100
•
The channel, language, country / region settings are downloaded to a Q-Link or
VIERA Link compatible equipment connected to the TV.
When the operation is completed, the channel at the lowest position will be
displayed.
41
Tuning and Editing Channels (DVB)
You can retune channels or make your favourite channel lists, skip unwanted channels, etc.
1
Select DVB-C or DVB-T
(p. 17)
TV
2
3
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
4
Select [DVB-C Tuning Menu] or [DVB-T Tuning Menu]
select
DVB-C Tuning Menu
DVB-T Tuning Menu
TV
Select one of the following functions
EXIT
select
DVB-C Tuning Menu
Favourites Edit
Channel List
Auto Setup
Manual Tuning
Update Channel List
New Channel Message
Signal Condition
Attenuator
■ To return to TV
•
The displayed item depends on the selected
mode.
Access
Access
Access
Access
Access
On
Access
Off
access / store
function items vary depending on the
• The
country you select (p. 12).
[Auto Setup] “Retuning from Setup
• Menu”
(p. 37, 38)
List favourite DVB channels [Favourites Edit]
Tuning and Editing Channels (DVB)
5
access
Access
Access
Create your favourite channel lists from various broadcasters (up to 4 : [Favourites]1 to 4).
The DVB Favourites lists are available from “Category” in the Information banner (p. 18) and the TV Guide screen (p. 21).
1 Select a channel to list (
DVB-C Favourites Editor
1
7
14
70
72
105
719
720
All DVB-C Channels
BBC One Wales
BBC THREE
E4
CBBC Channel
Cartoon Nwk
BBCi
BBC Radio Wales
BBC Radio Cymru
: Encrypted channel)
Sorting 123...
Favourites1
select
• To sort channel names in alphabetical order
(red)
• To display other Favourites
(green)
• To change the category
(blue)
39
2 Add it to the Favourites list
DVB-C Favourites Editor
1
7
14
70
72
105
719
720
All DVB-C Channels
BBC One Wales
BBC THREE
E4
CBBC Channel
Cartoon Nwk
BBCi
BBC Radio Wales
BBC Radio Cymru
• To add continuous block of channels to the list at once
Sorting 123...
make the block
(yellow)
Favourites1
1 BBC One Wales
add
•
A channel is added
To add all channels to the list
(yellow)
■ To edit Favourites list
While the cursor is in the Favourites field to edit
To move the channel
Select the new position
•
abc
(green)
or
jkl
mno
tuv
wxyz
• To delete the channel
Store
def
ghi
pqrs
(green)
(green)
• To delete all channels
(yellow)
• To name the Favourites
Set characters (maximum : ten characters)
Store
select
User input
(red)
Name
A
B
C D
E
F
G H
U
V W X
Y
Z
a
b
c
d
e
f
g
h
i
u
v
w
x
y
z
(
)
+
0
I
J
K
L M N O
P
Q
1
2
3
4
5
6
7
8
9
j
k
l
m n
o
p
q
-
.
*
_
R
S
T
!
:
#
r
s
t
BACK/
RETURN
set
use numeric buttons
• To “Characters
table for numeric buttons” (p. 97)
3 Store
BACK/
RETURN
Skip unwanted DVB channels, Edit DVB Channels [Channel List]
Tuning and Editing Channels (DVB)
You can hide unwanted DVB channels.
The hidden channels cannot be displayed except in this function. Use this function to skip unwanted channels.
Select a channel and reveal / hide
70
72
105
719
720
1
7
CBBC Channel
Cartoon Nwk
BBCi
BBC Radio Wales
BBC Radio Cymru
BBC ONE Wales
BBC THREE
: [Reveal]
: [Hide] (skip)
• To sort channel names in alphabetical order
• To change the category
(red)
(blue)
■ To edit channels
You can also edit each channel in Channel List.
To swap the channel position (if available)
Enter the new position number
•
abc
ghi
jkl
mno
pqrs
tuv
wxyz
(green)
Select the new position
(green)
or
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
Channel position
Coronation Street
20:00 - 20:55
Now
Info
Store
def
• To move the channel position (if available)
1
BBC ONE WALES
(yellow)
[Reveal] / [Hide]
■ To sort channel list
(green)
40
• To reveal all channels
select
Sorting 123...
All DVB-C Channels
20:35
All DVB-T Channels
Change category
Store
(green)
Set DVB channel manually [Manual Tuning]
Normally use [Auto Setup] or [Update Channel List] to retune DVB channels.
If tuning has not been done completely or for adjusting the direction of the aerial, use this function.
All channels found will be added to the Channel List.
•
DVB-C :
1 Enter the frequency
2 Select [Start scan]
DVB-C Manual Tuning
4 74,00 MHz
Auto
Auto
Start scan
Frequency
Symbol Rate
Service ID
Signal Quality
Signal Strength
No.
Free TV: 0
abc
Channel Name
100 %
100 %
New
Type
Pay TV: 0
Stopped
select
def
ghi
jkl
mno
pqrs
tuv
wxyz
access
set [Symbol Rate] and
• Normally
[Service ID] to [Auto].
Radio: 0
DVB-T :
1 Adjust frequency for each channel
2 Search
DVB-T Manual Tuning
Frequency
Signal Quality
Signal Strength
No.
Free TV: 0
[CH21]
Channel Name
Pay TV: 0
select channel
474,00 MHz
100 %
100 %
New
Type
Radio: 0
Stopped
adjust frequency
•
Set where the level of [Signal Quality]
becomes the maximum.
Data: 0
Update DVB channel automatically [Update Channel List]
You can add new channels, delete removed channels, update channel name and position automatically to Channel List.
DVB-T Update Channel List
Channel List is updated while keeping your settings in [Favourites Edit],
CH 5
69
Progress
[Channel List], [Child Lock], etc.
This will take about 3 minutes.
Depending on the signal condition, the update may not work properly.
CH
Channel Name
Type
Quality
•
•
Pay TV: 0
Searching
Radio: 0
Display a notification message [New Channel Message]
Selects whether to give a notification message when a new DVB channel is found. [Off] / [On]
Selecting OK will perform [Update Channel List].
New channels found!
Press OK to update channel list.
Press EXIT to ignore.
•
Check DVB signal [Signal Condition]
Selects a channel and checks the DVB signal condition.
A good Signal Strength is not an indication of suitable signal for DVB reception.
Please use the Signal Quality indicator as follows :
[Signal Quality] :
Green bar Good
Yellow bar Poor
Red bar Bad (Check the Terrestrial aerial or cable)
• To change the channel
Tuning and Editing Channels (DVB)
Free TV: 0
•
•
•
Example :
DVB-C Signal Condition
Channel Name
Signal Quality
Signal Strength
Bit Error Rate
Network Name
Parameter
70 CBBC Channel
90 %
80 %
These bars show the maximum signal value of the selected channel.
0.00E+00
Wenvoe
802,00 MHz, 64 QAM, 6940 kS/s
Reduce the DVB-C signal [Attenuator]
If the DVB-C signal is too strong, the interference may occur. In this case set to [On] to reduce the signal automatically.
This function is available only for DVB-C signal.
•
41
Tuning and Editing Channels (Analogue)
You can retune channels or skip unwanted channels, edit channels etc.
1
Select Analogue
(p. 17)
TV
2
3
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
4
Select [Analogue Tuning Menu]
select
Analogue Tuning Menu
Tuning and Editing Channels (Analogue)
5
TV
Select one of the following functions
select
Analogue Tuning Menu
Channel List
Auto Setup
Manual Tuning
Access
Access
Access
■ To return to TV
EXIT
access
•
•
The function items vary depending on the
country you select (p. 12).
[Auto Setup] “Retuning from Setup
Menu” (p. 38)
Skip unwanted Analogue channels, Edit Analogue channels [Channel List]
You can hide unwanted Analogue channels.
The hidden channels cannot be displayed except in this function. Use this function to skip unwanted channels.
Select a channel and reveal / hide
Analogue Channel List
1
2
3
4
5
6
7
42
access
Access
BBC1
*****
*****
*****
*****
*****
*****
select
[Reveal] / [Hide]
: [Reveal]
: [Hide] (skip)
• To reveal all channels
(yellow)
■ To edit channels
You can also edit each channel in Channel List.
To retune each channel ([Manual Tuning])
•
•
(red)
(see below)
To move the channel position
Select the new position
Store
(green)
(green)
• To rename the channel name
Set characters (maximum : five characters)
Store
select
Edit channel name
(blue)
Name
A
B
C D
E
F
G H
U
V W X
Y
Z
a
b
c
d
e
f
g
h
i
u
v
w
x
y
z
(
)
+
0
I
J
K
L M N O
P
Q
1
2
3
4
5
6
7
8
9
j
k
l
m n
o
p
q
-
.
*
_
R
S
T
!
:
#
r
s
t
BACK/
RETURN
set
use numeric buttons
• To “Characters
table for numeric buttons” (p. 97)
Channel position
Channel name
1
23:35
All Analogue Channels
CH23 SC1
ITV
Note
• If a VCR is connected only with the RF cable, edit [VCR].
Set Analogue channel manually [Manual Tuning]
[Fine Tuning]
Use to make small adjustments to the tuning of an individual programme (affected by weather conditions, etc.)
Set Analogue channel manually after Auto Setup.
Set [Sound System] and [Colour System], and then perform this function.
Normally set [Colour System] [Auto].
If a VCR is connected only with the RF cable, select channel position [0].
•
•
Analogue Manual Tuning
1 BBC1
Fine Tuning
Manual Tuning
Sound System
Colour System
CH33
2
78
1
SC1
Auto
Store
1 Select the channel position
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
3 Search
41
SC1 : PAL B, G, H / SECAM B, G
SC2 : PAL I
SC3 : PAL D, K / SECAM D, K
F : SECAM L, L’
2 Select the channel
Tuning and Editing Channels (Analogue)
[Manual Tuning]
4 Select [Store]
select
store
43
Timer Programming
Timer Programming from Menu
The Timer Programming menu allows you to choose programmes that you wish to remind watching or record to the external
recorder or the USB HDD. At the correct time, the TV will tune to the correct channel even if the TV is in Standby mode.
TV Guide may also be used to set timer programming event (p. 23).
This function is not available in Analogue mode.
Timer Programming can store up to 15 events.
Timer Programming only works reliably if correct time information is received via the signal from the broadcaster or service
provider.
For recording using Timer Programming, the TV must be either On or in standby. For reminders to be displayed, the TV must
be On.
No other channel can be selected while the recording of Timer Programming is in progress.
It may not be possible to record an encrypted programme (which is copy-protected).
When recording programmes to the external recorder, be sure to make the proper settings on the recorder connected to the
TV.
If a compatible recorder with Q-Link, VIERA Link or similar technologies is connected to the TV (p. 82, 83) and the [Link
Settings] (p. 34) are completed, no setting of the recorder is required. Also read the manual of the recorder.
If the recorder is not compatible with Q-Link, VIERA Link or similar technologies, make timer programming of the recorder.
For preparations of a recorder, read the manual of the recorder.
When recording programmes to the USB HDD, be sure to format the USB HDD and enable it for recording in [Recording
Setup] (p. 53).
Recordings to the external recorders are always in standard definition composite video via SCART, even if the original
programme is in high definition.
2 minutes before the starting time, a reminder message appears if you are watching TV.
•
•
•
•
•
•
•
•
•
•
•
• To remove the message and start the programming
• To cancel the programming
EXIT
1
Select the mode you want to set
(DVB-C or DVB-T)
Timer Programming
(p. 17)
TV
2
3
Display the menu
MENU
Select [Timer]
select
Main Menu
access
Picture
Sound
Timer
Setup
■ To return to TV
EXIT
4
■ To unlock the tuner
and stop recording
IDE
GU
44
EXIT
Select [Timer Programming]
Timer Programming
Off Timer
Auto Standby
Access
Off
Off
select
access
Set timer programming event details [Timer Programming]
1 Start making the settings
2 Select the function ([Ext Rec.], [USB HDD Rec.] or [Reminder])
select
[Ext Rec.] / [USB HDD Rec.] :
to record the programme to the external recorder or the USB HDD
When the start time comes, the channel will be switched automatically and the video and audio signals will be output. 2
minutes before the starting time, a reminder message appears if you are watching TV.
[Reminder] :
to remind you to watch the programme
When you are watching TV, a reminder message appears 2 minutes before the start time.
Press the OK button to switch to the programmed channel.
3 Set the channel, date and time (repeat the operations as below)
Set items in the order of 1 to 4.
select the item
3 and 4 can also be entered with numeric
• 1,buttons.
set
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
: Displayed if the timer programming events are overlapped
Timer Programming
Function
Wed 27.10.2010 10:46
No. Channel Name
Date
Start
End
D
7 BBC7
<TIMER>
Wed 27.10.2010
17:00
18:30
(90 min.)
Ext Rec.
D
1 BBC1
<TIMER>
STTL Wed 27.10.2010
18:00
20:00
(120 min.)
Ext Rec.
C
3 ITV1
<TIMER>
Thu 28.10.2010
21:30
22:30
(60 min.)
---
---
--:--
--:--
--:--
---
---
--:--
--:--
--:--
Change function
EXIT
Store timer
Select
RETURN
Remaining Capacity:
0
9
•
(yellow)
(Press again to remove subtitles)
Duration (automatic display)
1/1
500GB (50%)
1
2
3
4
Information of the USB HDD (if available)
[C] : DVB-C
[D] : DVB-T
You cannot change the mode within the menu.
Timer Programming
Reminder
Records with subtitles (if available)
To indicate this
•
1 Channel number
2 Date
3 Starting time
4 Ending time
one day ahead
daily or weekly (press repeatedly)
Sun-Sat] : Sunday to Saturday
• [Daily
Mon-Sat] : Monday to Saturday
• [Daily
Mon-Fri] : Monday to Friday
• [Daily
• [Weekly Sat/Fri/Thu/Wed/Tue/Mon/Sun] : Same time on the same day every week
4 Store
45
■ To change a timer programming event
■ To record with subtitles (if available)
Select the programme to be changed
Select the programme to record with subtitles
select
(yellow)
Correct as necessary (p. 45)
• Each time pressed :
access
auto
■ To cancel a timer programming event
off
■ To cancel a timer programming event
Select the programme to be deleted
temporarily
Select the programme to be cancelled
(red)
(blue)
• Each time pressed :
cancel
stop cancelling
Note
that the LED is orange. If not, timer programmes are not active or not stored.
• Check
Programming reminder messages will remain displayed until one of the following occurs :
• Timer
• You press the OK button to view the programme or the EXIT button to cancel the reminder.
• The timer programming event that the reminder is set for ends.
identifies that any timer programming events have overlapped. [Ext Rec.] and [USB HDD Rec.] are given priority over
• “!”[Reminder].
As for the overlapped two or more [Ext Rec.] / [USB HDD Rec.], the first timer programming event starts and
finishes as programmed. The next timer programming event can then start.
recording of Timer Programming will automatically change to the programmed channel 10 seconds before the start
• The
time.
stop recording the timer programming event directly prior to the start time, it may be necessary to stop the recorder
• Tomanually.
recording of Timer Programming will be performed even if the TV is in REW LIVE TV recording (p. 56) or Pause Live TV
• The
recording (p. 85). In this case, these recordings will be cancelled.
Child Lock
Timer Programming | Child Lock
You can lock specific channels / AV input terminals and control who watches them.
When the locked channel / input is selected, a message appears; by entering the PIN number, you can watch it.
1
2
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
3
■ To return to TV
EXIT
46
Select [Child Lock]
1/2
Eco Navigation
Recording Setup
Link Settings
Child Lock
DVB-C Tuning Menu
Language
Display Settings
Common Interface
Network Setup
select
access
Access
Control channel audience [Child Lock]
1 Enter the PIN number (4 digits)
abc
Child Lock-PIN Entry
Please enter new PIN
PIN
* * * *
def
ghi
jkl
mno
pqrs
tuv
wxyz
the PIN number twice at first setting.
• Enter
a note of the PIN number in case you forget it.
• Make
may be stored as the default PIN number which depends on
• “0000”
the country you select (p. 12).
2 Select [Child Lock List]
select
Child Lock
Change PIN
Child Lock List
Parental Rating
Access
No limit
access
3 Select the channel / input to be locked
Child Lock List - TV and AV
101
7
14
VCR
1
2
Name
BBC 1 Wales
BBC THREE
E4C
Input
DVB-C
DVB-T
DVB-T
Analogue
Analogue
Analogue
External
External
BBC1
*****
AV1
AV2
Sorting 123...
Type
Free TV
Free TV
Free TV
Analogue
Analogue
Analogue
AV
AV
Lock
select
lock
: Appears when the channel / input is locked
cancel
• ToSelect
the locked channel / input
• To sort channel names in alphabetical order
(red)
• To cancel all locks
• To lock all
(green)
• To jump to the top of the next input
(yellow)
(blue)
select
Child Lock
Change PIN
Child Lock List
Parental Rating
Access
No limit
Child Lock
■ To change the PIN number
1. Select [Change PIN]
access
2. Enter a new PIN number twice
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
■ To set Parental Rating
availability of this function depends on the country you select (p. 12).
•If The
the DVB programme has the rated information for over the selected age, you have to enter the PIN number to watch
(depending on the broadcaster).
Select [Parental Rating] and set an age for the restriction of programmes.
select
Child Lock
Change PIN
Child Lock List
Parental Rating
No limit
access / store
Note
• Setting [Shipping Condition] (p. 50) erases the PIN number and all settings.
47
Input Labels
For easier identification and selection of the input mode, you can label each input mode or skip terminal that is not connected
to any equipment.
To select the input mode (p. 26)
•
1
Display the menu
2
Select [Setup]
MENU
select
Main Menu
access
Picture
Sound
Timer
Setup
3
Select [Display Settings]
select
Display Settings
4
Select [Input Labels]
select
Display Settings
Input Labels
Input Labels
TV
■ To return to TV
EXIT
5
access
Access
access
Access
Select an input terminal
1/2
Input Labels
select
DVD
AV2
COMPONENT
PC
HDMI1
HDMI2
HDMI3
HDMI4
DVB-C
AV1
AV2
COMPONENT
PC
HDMI1
HDMI2
HDMI3
HDMI4
DVB-C
access / store
The labels you set will be displayed in [Input
Selection] menu (p. 26), [TV Selection] menu
(p. 17) or banner.
If [Skip] is selected, you cannot select the
mode.
•
2/2
Input Labels
DVB-T
Analogue
DVB-T
Analogue
■ User input
You can name each input mode freely.
1 Select [User input]
2 Set characters (maximum : ten characters)
select
access
Name
A
B
C D
E
F
G H
U
V W X
Y
Z
a
b
c
d
e
f
g
h
i
u
v
w
x
y
z
(
)
+
0
I
J
K
L M N O
P
Q
1
2
3
4
5
6
7
8
9
j
k
l
m n
o
p
q
-
.
*
_
R
S
T
!
:
#
r
s
t
use numeric buttons
• To “Characters
table for numeric buttons” (p. 97)
48
3 Store
select
User input
set
BACK/
RETURN
Using Common Interface
The Common Interface Module menu provides access to software contained on Common Interface (CI) Modules.
This function may not be available in some countries or regions.
Video and audio signals may not be output depending on broadcasts or services.
Although CI module may enable you to view some services, this TV does not guarantee all services (e.g. encrypted pay-TV
channels).
Please use only the approved CI module by the broadcaster.
Consult your local Panasonic dealer or broadcasters for more information and conditions of the services.
•
•
CI slot
Caution
the cover before
• Remove
using CI slot.
Off Mains power On / Off switch whenever inserting or
• Turn
removing the CI module.
card and a card reader come as a set, first insert the
• Ifcarda view
reader, then insert the view card into the card reader.
• Insert the module in the correct direction.
Insert or remove straightly
and completely
CI module
Side of the TV
Insert the CI module (optional)
The features that appear on screen are dependent on the contents of the selected CI module.
Normally encrypted channels will appear. Follow the on screen operation guide.
If encrypted channel does not appear, perform below.
For more details, see the manual of the CI module, or check with the broadcaster.
•
•
•
1
Select DVB-C or DVB-T
(p. 17)
TV
2
3
Display the menu
MENU
Select [Setup]
access
Picture
Sound
Timer
Setup
4
Select [Common Interface]
Using Common Interface
select
Main Menu
select
Common Interface
access
Access
■ To return to TV
EXIT
5
Access Common Interface
Common Interface
Slot 1:
Module inserted
access
■ How to operate services by following the on screen operation guide
Example :
Select, go
•
• Symbol :
• Coloured characters
Coloured button
• On screen operation guide may not correspond to the remote control buttons.
49
Shipping Condition
Resets the TV to its original condition, i.e. no channels tuned in.
All settings other than [USB HDD Setup] are reset (channels, picture, sound settings, etc.).
To retune TV channels only, e.g. after moving house “Retuning from Setup Menu” (p. 37, 38)
•
1
2
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
3
Select [System Menu]
2/2
Network Setup
DivX VOD
System Menu
Other Settings
®
4
Access
select
access
Select [Shipping Condition]
■ To return to TV
Shipping Condition
EXIT
select
System Menu
USB Keyboard Layout
Shipping Condition
System Update
Software Licence
System Information
English(UK)
Access
access
Restore Settings [Shipping Condition]
1 Check the message and initialise
2 Follow the on screen instructions
Shipping Condition
All tuning data will be erased
Reset to Factory Shipping Condition
Completed.
Please switch off TV.
1
Are you sure ?
(Confirm)
Are you sure ?
2
Setup] will automatically start
• [Auto
when Mains power On / Off switch is
next turned On. (p. 12)
(Confirm)
3
(Start [Shipping Condition])
50
Updating the TV Software
From time to time, a new version of software may become available for download to enhance the performance or operations
of the TV.
If there is an update available, a notification banner is displayed when the channel has the update information.
To download
If you choose not to download
•
•
EXIT
You can update any new software automatically or update manually.
1
2
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
3
Select [System Menu]
select
System Menu
4
EXIT
Select [System Update]
select
System Menu
System Update
access
Access
Update TV’s software system [System Update]
■ To update automatically
Select [Auto Update Search in Standby]
Auto Update Search in Standby
System Update Search Now
time you set, the TV automatically performs a
• Every
search in standby and downloads an update, if any
select
System Update
Off
Updating the TV Software
■ To return to TV
access
Access
software updates are available.
access / store
If System Update is performed, the software will be updated (it
may change TV functions).
If you do not wish to do so, set [Auto Update Search in Standby]
to [Off].
automatic updating is performed under the
• The
following conditions :
• Standby (TV turned Off with the remote control)
• Recording of Timer Programming, Direct TV
Recording or One Touch Recording is not in
progress.
■ To update immediately
1 Select [System Update Search Now]
Auto Update Search in Standby
System Update Search Now
2 Searches for an update (for
select
System Update
Off
Access
3 Download
several minutes) and displays a
corresponding message if any
access
Note
may take for about 60 minutes.
• Download
software download and update, DO NOT switch Off the TV.
• During
message might be the notification beforehand. In this case, the schedule information (the date that the new version
• The
can be used) will appear. You can set the reservation for update. The update will not start when the TV is set to Off.
51
Displaying PC Screen on TV
The screen of the PC connected to the TV can be displayed on the TV.
You can also listen to PC sound with the audio cable connected.
To connect PC (p. 90)
•
1
Select the external input
2
Select [PC]
AV
select
Input Selection
AV1
AV2
COMPONENT
PC
HDMI1
HDMI2
HDMI3
HDMI4
TV
SD Card/USB
■ To return to TV
TV
access
•
•
Corresponding signals (p. 98)
If [H-freq.] or [V-freq.] is shown in red, the signals
may not be supported.
PC menu setting
• To make settings
Menu
“How to Use Menu Functions” (p. 29)
Item
Input Resolution
Clock
Adjustments / Configurations (options)
Switches to a wide view
VGA (640 × 480 pixels), WVGA (852 × 480 pixels), XGA (1,024 × 768 pixels),
WXGA (1,280 × 768 pixels, 1,366 × 768 pixels)
Options change depending on signals
•
•
Set to the minimum level if noise occurs
Adjusts horizontal position
PC Setup
Setup
Displaying PC Screen on TV
H-pos
Adjusts vertical position
V-pos
Eliminates flicker and distortion
Clock Phase
• Other items
Note
after Clock adjustment
• Adjust
• Set to the minimum level if noise occurs
Sync
Chooses another synchronous signal if the image is distorted
[H & V] / [On Green]
[H & V] : by the horizontal and vertical signals from your PC
[On Green] : by the green signal from your PC (if available)
Reset to Defaults
Press the OK button to reset to the default PC Setup settings
(p. 30 - 33)
HDMI-compatible PC, possible to connect to HDMI terminals (HDMI1 / HDMI2 / HDMI3 / HDMI4) by using HDMI cable
• For
(p. 96).
52
USB HDD Recording
You can record the digital TV programmes to the connected USB HDD and enjoy playing back in various ways.
Analogue TV programme cannot be recorded to the USB HDD.
The data broadcasting (MHEG, etc.), radio broadcasting and the periods without any signal will not be recorded.
Not all the programmes can be recorded depending on the broadcaster and service provider.
For more information of the USB HDD (p. 95)
•
•
•
•
Caution
data in the USB HDD will be erased in the following cases :
• All• When
formatting the USB HDD with the TV “Setting for USB HDD” (see below)
• When formatting the USB HDD to use on PC
the TV is repaired due to a malfunction, you may have to format the USB HDD again with the TV to use it. (All data will
• When
be erased when formatting.)
to use the USB HDD with your PC after recording with this TV, format it again on your PC. (You cannot format it with
• Intheorder
format function in the OS of Windows XP.)
data recorded to the USB HDD with this TV can only be played back on this TV. You cannot play back its contents with
• The
another TV (including the TV of the same model number) or any PCs.
USB HDD connection
Connect the USB HDD to the USB 1 port.
to connect the USB HDD to the socket outlet.
• BeDosure
not turn off or disconnect the USB HDD during
• operation.
It may cause malfunction of the drive or damage
socket outlet
the recorded data.
USB cable
• To remove the USB HDD safely from the TV
(p. 19, 54)
USB HDD
Setting for USB HDD
Format and setup the USB HDD with this TV in order to use it for recording.
Before the settings, connect the USB HDD (see above) and be sure to turn on the USB HDD.
You cannot change the settings for the USB HDD while recording is in progress.
Please note that USB HDD will be formatted and all data in it will be erased when you format it.
•
•
•
2
Display the menu
MENU
Select [Setup]
select
Main Menu
USB HDD Recording
1
access
Picture
Sound
Timer
Setup
3
Select [Recording Setup]
select
Recording Setup
■ To return to TV
EXIT
4
Access
access
Select [USB HDD Setup] and set
select
Recording Setup
USB HDD Setup
One Touch Recording
REW LIVE TV
Access
180 minutes
Off
access
53
Setup the USB HDD [USB HDD Setup]
All the USB devices recognised as a mass storage device will be listed.
You can only choose one USB HDD for recording at a time.
•
1 Select the USB HDD for recording and start setup
USB HDD Setup
Product
USB Drive A
USB Flash Disk
select
Name
access
USB HDD may not be displayed.
• Some
• For the information of the highlighted device
2 Caution and confirmation of using USB HDD
Select [Yes] to proceed
Format
Format
Yes
Format
This device will be formatted and
all contents deleted.
Are you sure?
To use this device for recording,
it must be formatted first.
Continue?
The data recorded to the USB HDD with this TV can only
be played back on this TV.
You cannot playback it with other TV (including the TV
of the same model number) or any PCs.
If your TV is repaired due to a malfunction, the USB
HDD may not be available with your repaired TV.
Continue?
Yes
Yes
No
No
select [Yes]
set
No
select [Yes]
set
select [Yes]
set
3 Confirmation of USB HDD name
Format
select
Name : USB Drive A
Edit name?
set
Yes
No
The name for the USB HDD is created automatically. If you want to edit the name, select [Yes].
Set characters
Store
USB HDD Recording
USB HDD 1
Name
A
B
BACK/
RETURN
select
USB HDD
C D
E
F
U
V W X
Y
Z
a
b
c
d
e
f
G H
g
I
J
K
L M N O
S
T
0
1
2
3
4
5
6
7
8
9
!
:
#
h
i
j
k
l
m n
o
p
u
v
w
x
y
z
(
)
P
Q
q
R
r
s
t
+
-
.
*
_
set
•
You can set characters by using numeric buttons.
4 Confirmation to enable USB HDD for recording
If the formatted USB HDD for recording already exists, this confirmation screen will be displayed to switch to enable this USB
HDD for recording.
Format
select [Yes]
Do you want to enable this
device now for recording?
When disconnecting any USB device,
always use the "Safely Remove USB" function
in the USB HDD Device Setup menu to avoid
any corruption of recorded content.
Yes
No
USB HDD Setup
Product
USB Drive A
USB Flash Disk
set
Name
USB HDD 1
Mode
: The USB HDD is available for recording / playing back.
Only one USB HDD on the list can be available for recording.
: The USB HDD is available for playing back.
USB HDD name is displayed
• To remove the USB HDD safely from the TV
• To format
(yellow)
• To set “Safely remove USB” in other conditions
54
(red)
(p. 19)
• To edit USB HDD name
(green)
Recording the TV programme to USB HDD
You can record the current programme immediately by using [One Touch Recording].
You can also record the current programme constantly for the selected period by using [REW LIVE TV] so that you can go back
or pause the current programme.
Ensure the connection and setup are completed before start recording (p. 53, 54)
Ensure not to connect or disconnect any USB devices during USB HDD recording. Otherwise the recording may not work
properly.
If the remaining capacity of the USB HDD is run out, the recording cannot be done.
•
•
•
1
2
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
3
Select [Recording Setup]
1/2
4
Access
■ To return to TV
EXIT
access
Select [One Touch Recording] or [REW LIVE TV]
select
Recording Setup
TV
select
USB HDD Setup
One Touch Recording
REW LIVE TV
180 minutes
Off
USB HDD Recording
Eco Navigation
Recording Setup
Link Settings
Child Lock
DVB-C Tuning Menu
Language
Display Settings
Common Interface
Network Setup
One touch direct TV recording - What you see is What you record
[One Touch Recording]
Recording the current programme in the USB HDD
immediately.
Select the maximum recording time
[30] / [60] / [90] / [120] / [180] (minutes)
LED will turn to orange (flash) while
One Touch Recording is in progress.
Recording Setup
USB HDD Setup
One Touch Recording
REW LIVE TV
180 minutes
Off
select
access / store
LED
55
■ To start One Touch Recording
Set the position to “TV”
Start
DVD/VCR
REC
TV
• No other channel can be selected while the recording is in progress.
■ To stop recording on the way
TV
EXIT
IDE
GU
DVD/VCR
or
■ To playback or delete the recorded contents
“Recorded TV mode” (p. 64)
if One Touch Recording is in progress, you can playback all the contents. However, the recording may not work properly
• Even
while playback.
Record constantly [REW LIVE TV]
Recording the current programme constantly.
Select [Auto] to start REW LIVE TV
select
Recording Setup
USB HDD Setup
One Touch Recording
REW LIVE TV
180 minutes
Auto
access / store
• When you select [Auto], the recording will start automatically.
■ To operate the REW LIVE TV
Set the position to “TV”
DVD/VCR
TV
• To pause
• To search backward (up to 90 minutes)
(Press and hold)
• After pausing or searching backward, the following buttons are available to operate.
USB HDD Recording
search backward
search backward /
forward
playback / pause
pause /
playback
playback
stop
search forward
stop (stops the current operation and
goes back to live TV)
(Press and hold)
stops the current
operation and
goes back to
live TV
■ To stop the REW LIVE TV
select [Off ]
Recording Setup
USB HDD Setup
One Touch Recording
REW LIVE TV
Off
Auto
you stop the REW LIVE TV, the recorded content for the REW LIVE TV will be
• Ifdeleted.
LIVE TV will be stopped and the recorded content deleted automatically in the following conditions :
• REW
(Even if REW LIVE TV stops for the following conditions, as long as the setting is [Auto], the new recording will start
automatically in a condition that makes the recording available.)
• selected other channels
• selected locked channel
• selected invalid channel
• no TV signal
• when the other recording starts
• when the TV is turned off or standby
56
Using Media Player
Media Player allows you to enjoy photo, video or music recorded on an SD Card and a USB Flash Memory, and recorded
contents on the formatted USB HDD.
VIERA IMAGE VIEWER is the function of the easy viewing for photos or videos recorded on an SD Card on the TV screen by
simply inserting into the SD Card slot.
Photo mode : Still pictures recorded by digital cameras will be displayed.
Video mode : (For SD Card or USB Flash Memory) Moving pictures recorded by digital video cameras will be played back.
Recorded TV mode : (For USB HDD) TV programmes recorded in USB HDD with this TV will be played back.
Music mode : Digital music data will be played back.
the operation, audio signal is output from AV1, AUDIO OUT, DIGITAL AUDIO OUT and HDMI2 (ARC function) terminals.
• During
But no video signals are output. AV1 can output audio signal if [AV1 out] is set to [Monitor] in the Setup Menu (p. 34). To use
HDMI2 with ARC function, connect an amplifier that has ARC function (p. 81) and set to use theatre speakers (p. 88).
shows the date on which the recording was made by the recording equipment. The file without record of the date is
• [Date]
shown “**/**/****”.
picture may not appear correctly on this TV depending on the recording equipment used.
• The
may take some time when there are many files and folders.
• Display
degraded files might be displayed at a reduced resolution.
• Partly
• The folder and file names may be different depending on the digital camera or digital video camera used.
To insert or remove the SD Card / USB Flash Memory
• For the USB HDD Connection
(p. 53)
■ USB Flash Memory
or remove straightly and completely.
• Insert
removing the USB Flash Memory, ensure to perform
• Before
“Safely remove USB” (p. 19).
• Connect to the USB 1, 2 or 3 port.
■ SD Card
To remove the SD Card
Gently insert the
SD Card label surface
facing front.
Push the centre of
the card
Push until a click
is heard
Using Media Player
To insert the SD Card
Cutout
the information of the devices “Devices for recording or playing back” (p. 95)
• For
• For the supported file format “Supported file format in Media Player and media servers” (p. 93, 94)
57
Starting Media Player
1
Insert the SD Card or USB Flash Memory to the TV
(p. 57)
play back contents in USB HDD, check the connection and settings are completed.
• To (p.
53, 54)
2
Start Media Player
Media Player
Signal output from all AV terminals will be
disabled during Media Player view.
Press OK to proceed.
• Also possible by pressing following buttons.
SD CARD
Press EXIT to return to TV viewing.
AV
3
“Watching External Inputs” (p. 26)
Select the device you want to access to
Media Player
select
access
devices are not connected,
• Ifthistwostepor more
will be skipped.
Drive Select
EXIT
Select
RETURN
Access
SD Card
USB Drive...
USB Flash...
SD Card
Selected device name
Using Media Player
4
TV
Media Player
select
access
■ To return to TV
EXIT
or
SD CARD
■ To return to the
previous screen
BACK/
RETURN
58
Select the content
Contents Select
EXIT
Select
RETURN
Access
Photo
Video
Music
Recorded TV
[Photo] “Photo mode” (p. 59)
[Video] “Video mode” (p. 63)
[Music] “Music mode” (p. 67)
[Recorded TV] “Recorded TV mode” (p. 64)
SD Card
can also access each mode directly by using VIERA TOOLS.
• You“How
to Use VIERA TOOLS” (p. 28)
formatted USB HDD, this step will be skipped and recorded contents list will be
• For
displayed. (p. 64)
Photo mode
Photo mode will read all “.jpg” extension files in the SD Card or USB Flash Memory.
The thumbnail of all the photos in the SD Card or USB Flash Memory will be displayed.
Example : Thumbnail - [All photos]
Media Player
View
Select
Slideshow
All photos
Photo
SD Card
Info
EXIT
OPTION
Option Menu
RETURN
View Select
Drive Select
Selected device name
Contents Select
: Error display
■ To return to TV
EXIT
or
•
•
SD CARD
To change the back ground music “Photo Settings” (p. 60)
To display the information of the highlighted photo
1/48
■ To return to the
File name
File number / Total file number
p1010001.JPG
Date
previous screen
23/10/2010
Pixel
BACK/
RETURN
1600X1200
■ To sort by folder, recorded date or recorded month
1 Display the view selection
(green)
2 Select the sort type
select
access
[Folder view] :
Displays the thumbnail grouped by folder
The files which are not into a folder will be collected to the folder
named “/”.
[Sort by Date] :
Displays the thumbnail grouped by the same date
The group of the photos without recorded date is shown as
[Unknown].
[Sort by Month] :
Displays the thumbnail grouped by the same month
The group of the photos without recorded date is shown as
[Unknown].
•
•
Using Media Player
Folder view
Sort by Date
Sort by Month
•
3 Select one of the sorted groups to display the thumbnail of the selected group
Media Player
Sort by Date
Photo
23/10/2010
25/10/2010
01/11/2010
05/11/2010
10/11/2010
24/11/2010
01/12/2010
03/12/2010
20/12/2010
22/12/2010
Access
Select
Slideshow
Info
EXIT
OPTION Option Menu
RETURN
View Select
Drive Select
22/11/2010
select
thumbnail of the selected group
23/11/2010
SD Card
Contents Select
• To return to the thumbnail of all photos
(green)
• To display the information of the highlighted group
select
[All photos]
access
1/12
Folder name
23/10/2010
Number of files
3
Group number /
Total group number
Folder name, date or month
59
[Single view] - Photos are displayed one at a time.
Select the file from the thumbnail of photos to be viewed
select
access
Example :
Single view
display / hide the operation
• Toguide
• To operate Single view
To the previous photo
Slideshow
• To return to thumbnail
Single view
To the next photo
BACK/
RETURN
EXIT
Select
RETURN
•
Stop
Rotate
Operation guide
Stop
(return to thumbnail)
To rotate 90°
(blue)
[Slideshow] - Slideshow will complete when all photos have been viewed within the present thumbnail.
1 Select the file from the thumbnail of photos
2 Start Slideshow
for the first view
(red)
select
• To display / hide the operation guide
• To pause (return to Single view)
• To return to thumbnail
BACK/
RETURN
Photo Settings
Setup the settings for Photo mode.
1 Display the option menu
Using Media Player
OPTION
2 Select [Slideshow Settings]
3 Select the items and set
Option Menu
Slideshow Settings
Slideshow Settings
Frame
Colour Effect
Transition Effect
Screen Mode
Burst Playback
Interval
Repeat
Back Ground Music
access
Off
Off
Fade
Normal
Off
5 seconds
On
select
access / store
Note
quality may become lower depending on the slideshow settings.
• Picture
• Picture setting may not work depending on the slideshow settings.
60
Menu
Item
Frame
Adjustments / Configurations (alternatives)
Selects the frame type of the slideshow
[Off] / [Multi] / [Collage] / [Drift (+ calendar)] / [Drift] / [Gallery (+ calendar)] /
[Gallery] / [Cinema]
[Multi] :
9 photos are displayed orderly at once.
[Collage] :
Each photo is displayed at a random position and random scale.
[Drift (+ calendar)] / [Drift] :
Photos are displayed like flow images.
You can select to display the calendar or not. The month of calendar is turned by
pressing left or right cursor button.
[Gallery (+ calendar)] / [Gallery] :
The various sizes of photos in the frame are displayed.
You can select to display the calendar or not. The month of calendar is turned by
pressing left or right cursor button.
[Cinema] :
Photos are displayed like old films (sepia tone)
•
•
Slideshow Settings
Colour Effect
Selects the colour effect of photos on Single view and Slideshow
[Off] / [Sepia] / [Gray scale]
Transition Effect
Selects the transition effect for switching the photo during the slideshow
[Off] / [Fade] / [Slide] / [Dissolve] / [Motion] / [Random]
[Fade] : The next photo fades in gradually.
[Slide] : The next photo slides and appears from the left side.
[Dissolve] : Each photo is dissolved when switching to the next photo.
[Motion] : Each photo is displayed with an effect of enlarging, reducing, moving up or
moving down.
[Random] : Each transition is selected at random.
This function is available when [Frame] is set to [Off ].
•
Burst Playback
•
•
•
Selects whether to display burst photos in a fast-paced slideshow mode
[Off] / [On]
This function is not available when [Transition Effect] is set to [Motion].
•
Using Media Player
Screen Mode
Selects whether enlarged or normal viewing on Single view and Slideshow
[Normal] / [Zoom]
This function is not available when [Frame] is set to [Collage].
This function is not available when [Transition Effect] is set to [Motion].
Depending on the photo size, it may not be fully enlarged to fill the screen, e.g.
portrait style picture.
Selects slideshow interval [5] / [10] / [15] / [30] / [60] / [90] / [120] (seconds)
Interval
• This function is not available when [Transition Effect] is set to [Motion].
Repeat
Slideshow repeat [Off] / [On]
61
Menu
Item
Adjustments / Configurations (alternatives)
Selects the back ground music during Photo mode
[Off] / [Type1] / [Type2] / [Type3] / [User] / [Auto]
[Type1], [Type2] and [Type3] are the fixed music each installed in this TV.
[User] : Music data in the device registered by yourself will be played back.
To register the music
•
1. Select the music file
2. Select [File] or [Folder]
Slideshow Settings
Depending on the conditions of the
device, select folders until you reach the
desired music file.
Register Slideshow BGM?
File
Folder
select
Back Ground Music
PRIVATE
DCIM
MISC
001photo
002photo
003music
01 song.mp3
Type1
Back Ground Music
set
[File] : The selected music file will be
registered as back ground music.
[Folder] : All the music in the folder which
contains the selected music file
will be registered as back ground
music.
select
access
no music has been registered or the device which has the registered music is
• Ifremoved,
no sound will be produced.
[Auto] : Music data stored in the root folder of the current device will be played back
randomly.
If there is no available music data, no sound will be produced.
•
Change the device
You can change to the other device directly in the same mode if two or more devices are connected.
1 While the thumbnail is displayed,
2 Select the device you want to access to
Using Media Player
display the device selection
(yellow)
Media Player
All photos
Photo
select
access
Drive Select
EXIT
Select
RETURN
View
Access
Select
SD
Card
Slideshow
EXIT SD Card Info
OPTION
RETURN
View Select
USB Drive...
SD Card
USB Flash...
Drive Select
Contents Select
Selected device name
Change the contents
You can switch to the other mode of Media Player from the thumbnail view.
The mode can be switched in the current device.
•
1 While the thumbnail is displayed,
display the contents selection
2 Select the contents
Media Player
Photo
All photos
select
access
(blue)
Contents Select
EXIT
Select
RETURN
View
Access
Select
SD
Card
Slideshow
62
EXIT Photo InfoVideo
Music
OPTION
RETURN
View Select
Drive Select
RecordedSD
TV Card
Contents Select
[Photo] “Photo mode” (p. 59)
[Video] “Video mode” (p. 63)
[Music] “Music mode” (p. 67)
[Recorded TV]
“Recorded TV mode” (p. 64)
Video and Recorded TV mode
•
Supported file format
(p. 93)
Video mode
(For SD Card or USB Flash Memory)
The thumbnail of video titles in the SD Card or USB Flash Memory will be displayed.
Example : Thumbnail - [Title view]
Title view The preview will start when the title is
Media Player
Video
highlighted if it supports a preview.
To turn off the preview
Trip1
Trip2
Trip3
Trip4
Trip5
Room
Nature1
“Video Setup” (p. 66)
To display the information of the highlighted
Nature2
Nature3
Nature4
Nature5
Nature6
2010_4
2010_7
title
•
•
1/15
2010_9
Title
Access
Select
EXIT
RETURN
OPTION
SD Card
Info
Option Menu
Drive Select
Play
Trip1
Date & Time
19/02/2010 11:21
Number of scenes
8
Duration
00h15m39s
Contents Select
Selected device name
: Error display
: The file does not support thumbnail view.
File format
Title number /
Total title number
view the scenes of the title
• ToSelect
the title
Example : Thumbnail - [Scene view]
Media Player
Trip1_1
Trip1_2
Title view > Trip1
Video
Trip1_3
Trip1_4
Trip1_5
Trip1_6
•
•
Trip1_7
Trip1_8
Play
Select
EXIT
RETURN
Play
OPTION
Info
Option Menu
Drive Select
The preview will start when the scene is
highlighted if it supports a preview.
To turn off the preview
“Video Setup” (p. 66)
To display the information of the highlighted
scene
SD Card
Contents Select
Trip1_1
Date & Time
19/02/2010 11:21
Duration
00h04m12s
File format
Scene number /
Total scene number
access
■ Playback from Title view
TV
■ To return to TV
EXIT
or
Playback of the selected title will start.
To repeat playback “Video Setup” (p. 66)
•
1 Select the title
select
SD CARD
■ To return to the
previous screen
BACK/
RETURN
(red)
Playback will start from the selected scene to the end of the title.
To repeat playback “Video Setup” (p. 66)
•
select
structure of titles
• The
and scenes may vary
2 Start playback
■ Playback from the selected scene in the title (SD-Video or AVCHD)
1 Select the title
Note
Using Media Player
select
1/8
Scene
2 Select the scene
select
3 Start playback
(red)
access
depending on the digital
video camera used.
63
■ How to operate in the playback
Example : Playback
SD
19/02/2010 11:21
display / hide the operation guide and
• Toinformation
banner
00:15:39
00:02:05
• To change aspect
ASPECT
the previous title /
• Toscene
• To operate the playback
EXIT
Rewind
RETURN
Pause / Playback
(red)
• To the next title / scene
Fast forward
Operation guide
Information banner
(green)
Stop
• To return to thumbnail
can also use the following buttons. (p. 27)
• You
Set the position to “TV”
DVD/VCR
BACK/
RETURN
TV
■ To change the device “Change the device” (p. 62)
■ To change the content in the current device “Change the contents” (p. 62)
Recorded TV mode
(For USB HDD)
Contents list of the USB HDD will be displayed.
Example : Contents list
Media Player
All
Duration
00:00
Not Viewed
Recording
Protected
Grouped
Recorded TV
Remaining capacity of the HDD
Remaining Capacity 500GB (50%)
Not Viewed
Channel
Date
D BBC 1
Thu 28/10
12:00
Mon 10/1
D ITV
13:30
Sat 15/1
D BBC 2
13:50
Title
Das Erste
1
News
3
Cinema
1
• This value may not be accurate depending on the condition.
can also access the contents list directly by using VIERA
• You
TOOLS.
“How to Use VIERA TOOLS” (p. 28)
• To display the information of the highlighted content
Select
EXIT
RETURN
Play
Using Media Player
OPTION
Option Menu
Delete
Info
USB HDD 1
Chapter List
Select
[All] :
All the recorded contents are listed.
[Not Viewed] :
Contents not played back are listed.
- Channel
DVB-T, BBC 1
- Title
Das Erste
- Date & Time
Wed 27/10/2010 12:00
- Duration
00:20
: Content not played back (Once you playback the content, this icon will disappear.)
: Content under recording (You can playback this content even if under recording.)
: Protected content cannot be deleted.
: Two or more contents are grouped.
■ Playback the content from the list
1 Select the content
2 Start playback
select
■ To edit recording content [Create Group] / [Release Group] / [Change Protect Status]
1 Select and tick the content
to edit
2 Display the option menu
OPTION
(blue)
3 Select the item and edit
Option Menu
Create Group
Release Group
Drive Select
Contents Select
Change Protect Status
select
64
edit
■ Delete the selected content
1 Select the content
2 Delete the content
select
3 Confirm
Delete
(red)
select
set
Are you sure you want to delete ?
select two or more
• Tocontents
No
Yes
(blue)
■ How to operate in the playback
Example : Playback
USB Das Erste
• To display / hide the operation guide and information banner
00:15:39
00:02:05
• To operate the playback
Rewind
Manual skip
EXIT
[Manual skip]
Press to skip forward about 30 seconds
Press and hold to skip backward about 15 seconds
•
•
RETURN
Operation guide
Pause / Playback
Information banner
Fast forward
Stop
• To repeat between the starting point “A” and finishing point “B”
Set “A” and “B” in order
• The points will be reset by pressing this button again or
(blue)
other operations.
• To the previous chapter
(red)
• To the next chapter
(green)
•
To change aspect
ASPECT
•
To display the subtitle (if available)
STTL
•
To return to list
BACK/
RETURN
Set the position to “TV”
DVD/VCR
TV
Chapter List
• To confirm or change the current status (if available)
“Display the selectable settings for the current status” (p. 19)
■ Chapter List
Using Media Player
• You can also use the following buttons. (p. 27)
You can start playback from the chapter list you select.
A recorded content is automatically divided into five-minute chapters.
The chapter list is not displayed while the selected content is being recorded.
To play back from the chapter list
•
•
(yellow)
select
playback
Chapter List
00:00:00 00:05:00
Note
• Depending on the recorded programmes, some playback operations may not work properly.
■ To change the device “Change the device” (p. 62)
■ To change the content in the current device “Change the contents” (p. 62)
65
Audio output Settings
You can enjoy the multi-channel sound via an amplifier connected to DIGITAL AUDIO OUT or HDMI2 (ARC function) terminal.
To confirm or change the current sound status “Confirm or change the current status” (p. 67)
•
1 Display the menu
2 Select [Sound]
MENU
3 Select [SPDIF Selection] and set
2/2
Main Menu
Picture
SPDIF Selection
Reset to Defaults
Auto
Reset
select
Sound
access / store
Timer
Setup
select
access
Menu
Item
Sound
SPDIF Selection
Adjustments / Configurations (alternatives)
SPDIF : A standard audio transfer file format
Selects the initial setting for digital audio output signal from DIGITAL AUDIO OUT and
HDMI2 (ARC function) terminals [Auto] / [PCM]
[Auto] : Dolby Digital Plus, Dolby Digital and HE-AAC (48 kHz) multi-channel are output
as Dolby Digital Bitstream.
DTS is output as DTS.
MPEG is output as PCM.
[PCM] : Digital output signal is fixed to PCM.
Video Setup
Using Media Player
Setup the settings for Video mode.
These settings are not available for the formatted USB HDD.
•
1 Display the option menu
2 Select [Video Setup]
OPTION
Option Menu
Video Setup Menu
Video Setup
Video Preview
Repeat
On
Off
select
access
Menu
Video Setup
66
3 Select the items and set
in the thumbnail view
Item
access / store
Adjustments / Configurations (alternatives)
Video Preview
Sets to start the preview of the title or scene in the thumbnail view [Off] / [On]
Image may not be displayed for an instant in the thumbnail view. Set the preview [Off ]
to resolve this.
Repeat
Playback repeat within the title or selected file (depending on the content) [Off] / [On]
•
Confirm or change the current status
You can confirm or change the current status of the content.
Menu items and selectable options vary depending on the content.
•
1 Display the option menu
2 Select [Video Setup]
3 Select the items and set
during playback
OPTION
Option Menu
Video Setup Menu
Video Setup
Multi Audio
Aspect Change
Repeat
Stereo
Aspect1
Off
select
access
Menu
Item
access / store
Adjustments / Configurations (alternatives)
Video Setup
Multi Audio
Allows you to select between selectable sound tracks (if available)
It may take several seconds to change the sound.
Aspect Change
[Aspect1] : Displays the content full-screen
[Aspect2] : Displays the content square
[Original] : Displays the content original size
You can also change the aspect using the ASPECT button.
Aspect change may not work depending on the content.
•
•
•
Music mode
•
Supported file format
(p. 93)
The thumbnail of music folders in the SD Card or USB Flash Memory will be displayed.
Example : Thumbnail - [Folder view]
Media Player
My Music_2
Access
Select
Play Folder
My Music_3
EXIT
RETURN
OPTION
Info
Option Menu
Drive Select
SD Card
Selected device name
Contents Select
• To display the information of the highlighted folder
1/3
Folder name
Using Media Player
My Music_1
Folder view
Music
Folder number / Total folder number
My Music_1
Number of files
11
■ To return to TV
EXIT
or
SD CARD
■ To return to the
previous screen
■ Playback from Folder view
All the files in the selected folder will be played back.
1 Select the folder
select
2 Start playback
(red)
BACK/
RETURN
67
■ Playback from File view
Selected file will be played back.
1 Select the folder
2 Select the file
Example : Thumbnail - File view
Media Player
Music
access
My Song_1
My Song_2
My Song_3
My Song_4
My Song_8
My Song_9
My Song_10
My Song_11
EXIT
RETURN
(red)
Folder view > My Music_1
select
Play
Select
Play Folder
3 Start playback
OPTION
My Song_5
My Song_6
Info
Option Menu
Drive Select
My Song_7
SD Card
Contents Select
• To display the information of the highlighted file
select
1/11
Title
File number / Total file number
My Song_1
Album
My Music_1
Artist
My Favourite
Track No.
1
Duration
00h03m29s
■ How to operate in the playback
Example : Playback
• To display / hide the operation guide
• To the previous track
•
•
(red)
My Song_9
My Favourite
My Music_1
00:02.43 / 00:05.44
To operate the playback
To the next track
Rewind
EXIT
(green)
Pause / Playback
RETURN
• To return to thumbnail
BACK/
RETURN
Fast forward
Stop
Using Media Player
Operation guide
■ To change the device
■ To change the content
“Change the device” (p. 62)
“Change the contents” (p. 62)
Music Setup
Setup the setting for Music mode (only available in the thumbnail view).
1 Display the option menu
OPTION
2 Select [Music Setup]
3 Set
Option Menu
Music Setup Menu
Music Setup
Repeat
select
access
One
select
access / store
[Folder] : Playback repeat within the
selected folder
[One] : Playback repeat of the selected
one file
68
Using Network Services
(DLNA / VIERA Connect)
DLNA®
This TV is a DLNA Certified™ product.
DLNA (Digital Living Network Alliance) is a standard that makes DLNA Certified digital electronics easier and more convenient
to use on a home network. To learn more, visit www.dlna.org.
It allows you to share photos, videos and music stored in the DLNA Certified media server (for example, PC with windows 7
installed, DIGA Recorder etc.) connected to your home network, and enjoy the contents on the TV screen.
For the supported file format (p. 93, 94)
AVCHD and DivX files are not supported by DLNA, but can be played by Media Player (p. 57).
•
•
■ Media server
Store photos, videos or music into the DLNA Certified media server, and then you can enjoy them on the TV.
To use a PC as a media server
Prepare the PC with Windows 7 or ensure the server software is installed on the PC.
“Windows 7” and “TwonkyMedia server 6 (installed on the PC with Windows 7, Windows Vista or Windows XP)” are the server
software that has been tested for compatibility with this TV (current as of January, 2011). Any other server software have not
been tested with this TV, therefore compatibility and performance cannot be assured.
Windows 7
The setup for homegroup settings of Windows 7 is required. For details, refer to the help functions of Windows 7.
TwonkyMedia server
“TwonkyMedia server” is the product of PacketVideo Corporation.
To obtain the Installation Guides for installing and setting “TwonkyMedia server”, visit the website of TwonkyMedia.
Additional fees may be charged to obtain server software.
•
•
Note
more information about the server software, please consult each software company.
• For
server software for the media server is installed on the PC, the data may be at risk of being accessed by other
• When
people. Please take care of the settings and connections under the network circumstances at the office, hotel or even at
•
Network connection
“Example 1” or “Example 2” in “Network connections” (p. 70)
Network setup
(p. 71 - 75)
DLNA operations
(p. 76 - 79)
VIERA Connect
You can access a selection of internet services from VIERA Connect home screen. For example, YouTube, Picasa Web Albums
(current as of January, 2011).
Network connection
“Example 1” or “Example 3” in “Network connections” (p. 70)
Using Network Services (DLNA / VIERA Connect)
home when not using a router.
To use a DLNA compatible DIGA Recorder as a media server
By connecting a DLNA compatible DIGA Recorder to your home network, you can enjoy and control it as one of the media
servers.
Please refer to the manual of your DIGA Recorder to confirm whether the recorder is compatible with DLNA.
Network setup
(p. 71 - 75)
VIERA Connect operations
(p. 16)
69
Network connections
To use only DLNA features, you can operate the features without broadband network environment.
To use VIERA Connect features, you need a broadband network environment.
If you do not have any broadband network services, please consult your retailer for assistance.
Set up and connect any equipment required for the network environment. You cannot make settings for the equipment on
this TV. Read the manual of the equipment.
Required speed (effective) : at least 1.5 Mbps for SD and 6 Mbps for HD picture quality, respectively. If the transfer speed is
not enough, contents may not be played back properly.
•
•
•
Example 1
(For DLNA and VIERA Connect)
Wired connection
Internet
LAN cable (Shielded)
Modem
Hub or Router
Wireless connection
DLNA Certified
media server
(for example, PC,
DIGA Recorder, etc.)
Wireless LAN Adaptor and Extension cable
“Optional accessories” (p. 6)
Connect to the USB 1, 2 or 3 port.
•
Access point
to use a LAN straight cable for this connection.
• Ensure
modem has no broadband router functions, use a broadband router.
• IfIf your
your modem has broadband router functions but there are no vacant ports, use a hub.
• Ensure
broadband routers and hubs are compatible with 10BASE-T / 100BASE-TX.
• If you usethatthetheequipment
compatible only with 100BASE-TX, category 5 LAN cables are required.
•
Example 2
Using Network Services (DLNA / VIERA Connect)
(For DLNA)
You can connect the TV and the equipment directly to use DLNA features.
DLNA Certified media server
(for example, PC,
DIGA Recorder, etc.)
LAN cable (Shielded)
• Ensure to use a LAN cross cable for this connection.
Example 3
(For VIERA Connect)
You can connect the TV and the telecommunication equipment directly to use VIERA Connect features.
Internet
LAN cable (Shielded)
Note
your Internet Service Provider (ISP) telecommunications company for further assistance regarding the network
• Contact
equipment.
the terms and conditions of the contracts with your Internet Service Provider (ISP) or telecommunications
• Confirm
company. Depending on the contracts, additional fees may be charged or multiple connections to the internet may be
impossible.
70
Network Setup
•
Ensure the connections are completed before starting Network Setup.
“Network connections” (p. 70)
1
2
Display the menu
MENU
Select [Setup]
select
Main Menu
access
Picture
Sound
Timer
Setup
3
Select [Network Setup]
select
Network Setup
access
Access
■ To return to TV
EXIT
Network Link settings
Sets the link settings to control this TV from the network equipment via the network.
2 Select the items and set
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Menu
Network Link Settings
VIERA Name
DLNA Remote Control
DLNA Remote Volume
Network Remote Control
Wired
---
VIERA
On
On
On
Access
ab-cd-ef-gh-ij-kl
select
select
access
change
access / store
Item
Adjustments / Configurations (alternatives)
Network Link Settings
VIERA Name
Sets your favourite name for this TV and this name will be used to display the name of
this TV on the screen of the other DLNA compatible equipment.
DLNA Remote Control
Enables to control the TV via the DLNA equipment [On] / [Off]
DLNA Remote Volume
Enables to control the volume of the TV via the DLNA equipment [On] / [Off]
Network Remote Control
Enables to control the TV from the network equipment (Smartphone, etc.)
[On] / [Off]
Depending on the area, this function may not be available. For details, consult your
local Panasonic dealer.
For more information of this function, visit the following website. (English only)
http://panasonic.jp/support/global/cs/tv/
Using Network Services (DLNA / VIERA Connect)
1 Select [Network Link Settings]
•
•
71
Wired connection settings
This setting is for the network connection by using the LAN cable.
1 Select [Network Type] and set to [Wired]
select
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Wired
---
access / store
If you make the network connection like “Example 2” (p. 70), you do not have to
set [Acquire DNS Address], [Proxy] and [Proxy Port].
ab-cd-ef-gh-ij-kl
2 Select [IP/DNS Settings] and set the items
select
Network Setup
IP/DNS Settings
access
Access
■ [Acquire IP Address] / [Acquire DNS Address]
Sets [IP Address], [Subnet Mask], [Gateway], [Primary DNS] and [Secondary DNS].
Select [Acquire IP Address] / [Acquire DNS Address] and set to [Auto] (recommended)
The available settings are displayed automatically.
IP/DNS Settings
•
Acquire IP Address
IP Address
Subnet Mask
Gateway
Acquire DNS Address
DNS Address
Proxy Settings
Auto
Manual settings
([IP Address], [Subnet Mask], [Gateway], [Primary DNS], [Secondary DNS])
select
Auto
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
access / store
3 Select [Proxy Settings] and set the items
select
IP/DNS Settings
Using Network Services (DLNA / VIERA Connect)
Acquire IP Address
IP Address
Subnet Mask
Gateway
Acquire DNS Address
DNS Address
Proxy Settings
Auto
access
Auto
Access
• After settings, return to [Network Setup] screen
BACK/
RETURN
■ [Proxy]
Sets Proxy address.
This is the address of the relay server that is connected to the target server instead of the browser and sends data to the
browser. Setting is required if specified by the provider.
1. Select [Proxy]
2. Enter the address
3. Store
•
Proxy Settings
Proxy
Proxy
Proxy Port
Host
0
A
B
BACK/
RETURN
C D
E
F
U
V W X
Y
Z
a
b
c
d
e
f
G H
g
I
J
K
L M N O
S
T
0
1
2
3
4
5
6
7
8
9
!
:
#
h
i
j
k
l
m n
o
p
u
v
w
x
y
z
(
)
P
Q
q
R
r
s
t
+
-
.
*
_
select
select
set
access
can set characters by using numeric
• You
buttons.
■ [Proxy Port]
Sets Proxy port number.
This number is also specified by the provider with the Proxy address.
•
1. Select [Proxy Port]
2. Move the cursor and enter the number
select
Proxy Settings
Proxy
Proxy Port
72
0
move
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
4 Select [Connection Test] and access to test
select
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Access
Wired
---
access
•
Performs automatic testing of the network connection for the TV. (It takes a
while to test.)
ab-cd-ef-gh-ij-kl
Connection Test
Check network cable connection.
Check acquired IP address.
Check for devices using same IP address.
Check gateway connection.
Check server connection.
: succeeded
The test is successful and the TV is connected to the network.
: failed
Check the settings and connections, and then perform this function again.
Wireless connection settings
This setting is for the network connection by using the Wireless LAN Adaptor. (Wireless connection)
Confirm the encryption key, settings and positions of your access point before starting setup. For details, read the manual of
the access point.
•
1 Select [Network Type] and set to [Wireless]
select
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Wireless
No settings
access / store
ab-cd-ef-gh-ij-kl
2 Select [Access Point Settings]
select
Network Setup
Wireless
No settings
access
ab-cd-ef-gh-ij-kl
3 Select the connection type and set
select
Connection Type
Please select network connection type.
WPS(Push button)
WPS(PIN)
Search for access point
Manual
access
• For details of each connection type (p. 74, 75)
• After settings, return to [Network Setup] screen
4 Confirm the connection status of [Access Point Settings]
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Wireless
Connected
ab-cd-ef-gh-ij-kl
---:
[No adaptor] :
[No settings] :
[Connecting...] :
[Connected] :
[Wired] is selected in [Network Type].
Wireless LAN Adaptor is not connected.
Setting for connecting to the access point has not been set.
Connecting to the access point in progress.
Wireless connection to the access point succeeded
To display the current access point settings, press the OK
button.
To change the settings, select [No] on this screen.
Some access points do not allow access to the internet.
Perform [Connection Test] (p. 74) to check if internet
connection is available.
[USB overcurrent] : Overcurrent error (p. 101)
Using Network Services (DLNA / VIERA Connect)
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
•
•
73
5 Select [Connection Test] and access to test
select
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Access
Wireless
Connected
access
Performs automatic testing of the network connection for the TV. (It takes a while
to test.)
ab-cd-ef-gh-ij-kl
Connection Test
: succeeded
The test is successful and the TV is connected to the network.
Check access point connection.
Check acquired IP address.
Check for devices using same IP address.
Check gateway connection.
Check server connection.
: failed
Check the settings and connections, and then perform this function again.
If you continue to have difficulty, please contact your internet service provider.
■ [WPS(Push button)]
press the WPS button on the access point until the light flashes
WPS(Push button)
1) Please press the ‘WPS’ button on the access
point until its light flashes.
2) When the light is flashing select ‘Connect’ on
TV.
If you are unsure, please check the instruction
manual of the access point.
Connect
connect the Wireless LAN Adaptor and the access point
that your access point supports WPS for this setup.
• Ensure
• WPS : Wi-Fi Protected Setup™
■ [WPS(PIN)]
1 Select your desired access point
select
Available Access Points
No.
1
2
3
SSID
Access Point A
Access Point B
Access Point C
Wireless type
11n(2.4GHz)
11n(5GHz)
11n(5GHz)
Encrypt
Reception
access
•
Ensure that your access point supports WPS for this setup.
• To search access points again • For the information of the highlighted access point
• To set manually
(yellow)
Using Network Services (DLNA / VIERA Connect)
2 Enter the PIN code to the access point, and then select [Connect]
WPS(PIN)
Please register the following PIN codes on the
access point.
PIN code : 12345678
Select ‘Connect’ after entering and saving the
settings on the access point.
Connect
■ [Search for access point]
Access points found automatically are listed.
1 Select your desired access point
Available Access Points
No.
1
2
3
SSID
Access Point A
Access Point B
Access Point C
Wireless type
11n(2.4GHz)
11n(5GHz)
11n(5GHz)
Encrypt
Reception
select
access
: Encrypted access point
• To search access points again
(yellow)
74
(red)
the information of the highlighted
• For
• To set manually
access point
(red)
2 Access the encryption key input mode
Encryption Key Setting
Connection will be made with the following settings:SSID : Access Point A
Authentication type : WPA-PSK
Encryption type : TKIP
the selected access point is not encrypted, the confirmation screen will be
• Ifdisplayed.
It is recommended to select the encrypted access point.
Please input the encryption key.
Encryption key
3 Enter the encryption key of the access point (Set characters one by one)
Store
select
Access Point Settings
BACK/
RETURN
Encryption key
A
B
C D
E
F
G H
I
J
K
L M N O
P
Q
R
S
T
U
V W X
Y
Z
0
1
2
3
4
5
6
7
8
9
!
:
#
a
b
c
d
e
f
g
h
i
j
k
l
m n
o
p
q
r
s
t
u
v
w
x
y
z
(
)
+
-
.
*
_
set
can set characters by using numeric
• You
buttons.
4 Select [Yes]
Access Point Settings
select
confirm
Encryption key is set to:XXXXXXXX
• To re-enter the encryption key, select [No].
Select ‘Yes’ to confirm.
Select ‘No’ to change.
Yes
No
■ [Manual]
You can setup SSID, authentication type, encryption type, and encryption key manually.
Follow the on screen instructions and set manually.
When you use 11n (5 GHz) for the wireless system between the Wireless LAN Adaptor and access point, please select [AES]
for the encryption type.
•
Access Point Settings
SSID Setting
Please input the SSID.
SSID is set to:XXXXXXX
SSID
XXXXXXX
Authentication Type Settings
Connection will be made with the following
settings:SSID : XXXXXXX
Select ‘Yes’ to confirm.
Select ‘No’ to change.
No
WPA2-PSK
WPA-PSK
Shared key
Open
Update TV’s software
Accesses the specific website to update TV’s software and search if any software updates are available.
Select [Software Update]
select
Network Setup
Connection Test
Network Type
Access Point Settings
IP/DNS Settings
Network Link Settings
Software Update
MAC Address
Wired
---
access
• Follow the on screen instructions
Access
ab-cd-ef-gh-ij-kl
Note
Network Setup
MAC Address
Using Network Services (DLNA / VIERA Connect)
Yes
Please select the authentication type.
[MAC Address]
MAC address is a unique address that identifies hardware in the network.
(for information only)
•
ab-cd-ef-gh-ij-kl
75
Using DLNA® features
•
Ensure the preparation of media server, network connections and network settings are completed.
“Media server” (p. 69), “Network connections” (p. 70), [Network Setup] (p. 71 - 75)
1
Display icons of the feature
2
Select [Media Server]
TO
VIERA OLS
select
access
Media Server
3
Select one of the media servers you want to access
Example : Media server list
Media Server
A
5
g
select
SERVER1
SERVER2
SERVER3
DIGA
access
Select
EXIT
RETURN
Access
OPTION
Option Menu
4
Info
display the information of the highlighted media
• Toserver
Available media servers
Total listed number
Using Network Services (DLNA / VIERA Connect)
76
4
Select the file
Example : File list
Pixel
Format
3648x2736
JPEG
■ To return to TV
Select
EXIT
RETURN
Media Server
SERVER1
P000102
P000135
P000180
P000214
P000251
P000276
P000293
V100025
V100042
M10054
M10078
09:54
13:18
11:31
15:20
12:39
14:06
13:52
15:56
10:08
14:48
19:58
View
OPTION
EXIT
2010-10-05
2010-11-20
2010-12-07
2010-12-10
2010-12-19
2010-12-25
2011-01-06
2011-01-12
2011-01-20
2011-01-28
2011-02-09
Option Menu
Slideshow
Info
28
select
access
on the conditions of media server, you may
• Depending
need to select the folder before selecting the file.
• To display the information of the highlighted file
■ To return to the
previous screen
BACK/
RETURN
Note
files are also listed but cannot be selected.
• Non-playable
the TV off, and then on again when changing or reconnecting the network
• Turn
connection.
For photo file
[Single view] - Photos are displayed one at a time.
Example :
Single view
return to list
• ToBACK/
• To display / hide the operation guide
RETURN
view
• To operate Single
To the previous photo
Single view
EXIT
Select
RETURN
• To rotate 90°
(blue)
To the next photo
Stop
Rotate
Slideshow
Operation guide
Stop
(return to list)
[Slideshow] - Slideshow will complete when all photos have been viewed within the list.
1 Select the photo file from the list for the first view
2 Start Slideshow
select
(red)
• To display / hide the operation guide
• To pause (return to Single view)
• To return to list
BACK/
RETURN
For video file
Playback - Playback will start.
Example : Playback
MEDIA SERVER 19/02/2010 11:21
00:15:39
00:02:05
display / hide the
• Tooperation
guide and
• To operate the playback
Rewind
Manual skip
EXIT
RETURN
Operation guide
Information banner
• To the previous content
(red)
• To the next content
(green)
• To change aspect
ASPECT
[Manual skip]
Press to skip forward about 30
seconds
Press and hold to skip backward
about 15 seconds
Pause / Playback
•
•
Fast forward
Stop
• To return to list
BACK/
RETURN
For music file
Playback - Playback will start
Example : Playback
• To display / hide the operation guide
• To the previous track
•
•
Using Network Services (DLNA / VIERA Connect)
information banner
(red)
My Song_9
My Favourite
My Music_1
00:02.43 / 00:05.44
To operate the playback
Rewind
EXIT
RETURN
Pause / Playback
Fast forward
Stop
To the next track
(green)
• To return to list
BACK/
RETURN
Operation guide
77
For DIGA Recorder
Control the DIGA Recorder
The screen of the DIGA Recorder will be displayed. You can control the functions of the DIGA Recorder with
this TV remote control according to the operation guide.
Example :
Before operating, register this TV on the DIGA Recorder.
All
For details, read the manual of the DIGA Recorder.
DIRECT NAVIGATOR (Grouped Titles)
Not Viewed
HDD
Movie
Social/Economy
19.08(Wed) Journal Télévisé / Météo
AV1
19.08(Wed)
Bibel TV
•
•
Time Remaining 36:17 (DR)
Sports
Liberty TV FR
Video (AVCHD)
Bibel TV das Gespräch
19.08(Wed) Start Time 11:01 Titles 27
OK
RETURN
WDR Aachen
18.08(Tue)
WDR aktuell
WDR Wuppertal
18.08(Tue)
WDR aktuell
Page 005/005
OPTION
Select
Delete Title
Option menu for each content
Setup the settings for Photo and Video file operations.
1 Display the option
menu
2 Select [Slideshow Settings], [Video Setup] or
[Music Setup]
OPTION
3 Select the items and set
Slideshow Settings
Option Menu
Transition Effect
Interval
Repeat
Back Ground Music
Slideshow Settings
Video Setup
Music Setup
Fade
5 seconds
On
Video Setup Menu
select
Video Preview
Repeat
access
On
Off
Music Setup Menu
Repeat
One
select
access / store
Menu
Slideshow Settings
Video Setup
Using Network Services (DLNA / VIERA Connect)
Music Setup
78
Item
Transition Effect
Interval
Adjustments / Configurations (alternatives)
Selects the transition effect for switching the photo during the slideshow
[Off] / [Fade] / [Slide] / [Dissolve] / [Motion] / [Random]
[Fade] : The next photo fades in gradually.
[Slide] : The next photo slides and appears from the left side.
[Dissolve] : The photo is replaced by an indefinite block unit.
[Motion] : The photo is replaced with enlarged, reduced, moved up or moved down.
[Random] : Each transition is selected at random.
Selects slideshow interval [5] / [10] / [15] / [30] / [60] / [90] / [120] (seconds)
• This function is not available when [Transition Effect] is set to [Motion].
Repeat
Slideshow repeat [Off] / [On]
Back Ground Music
Selects the back ground music during Photo mode
[Off] / [Type1] / [Type2] / [Type3] / [User] / [Auto]
Video Preview
Sets to start the preview of the title or scene in the thumbnail screen [Off] / [On]
Image may not be displayed for an instant in the thumbnail screen. Set the preview
[Off ] to resolve this.
Repeat
Playback repeat within the selected file [Off] / [On]
Repeat
Playback repeat [Off] / [Folder] / [One]
[Folder] : Playback repeat within the selected folder
[One] : Playback repeat of the selected one file
•
Audio output settings (for video contents)
You can enjoy the multi-channel sound via an amplifier connected to DIGITAL AUDIO OUT or HDMI2 (ARC function) terminal.
To confirm or change the current sound status “Confirm or change the current status” (p. 67)
•
1 Display the menu
MENU
2 Select [Sound]
3 Select [SPDIF Selection] and set
2/2
Main Menu
Picture
SPDIF Selection
Reset to Defaults
Auto
Reset
select
Sound
access / store
Timer
Setup
select
access
Menu
Item
Sound
SPDIF Selection
Adjustments / Configurations (alternatives)
SPDIF : A standard audio transfer file format
Selects the initial setting for digital audio output signal from DIGITAL AUDIO OUT and
HDMI2 (ARC function) terminals [Auto] / [PCM]
[Auto] : Dolby Digital Plus, Dolby Digital and HE-AAC (48 kHz) multi-channel are output
as Dolby Digital Bitstream.
MPEG is output as PCM.
[PCM] : Digital output signal is fixed to PCM.
VIERA Connect
•
•
•
• Setup menu (Items in [Setup] may change without notice.)
Customize HomeScreen
Changes the position of each services on VIERA Connect home screen
My Account
Confirms or removes the account information of the TV you entered on VIERA Connect
Lock
Sets to restrict access to some services
Beep
Sets beep sound On or Off when operating VIERA Connect
Notices
Displays the information of VIERA Connect
Note
to update the software when a software update notice is displayed on the TV screen. If the software is not updated,
• Beyousure
will not be able to use VIERA Connect.
You can update the software later manually
[Software Update] in [Network Setup] (p. 75)
home screen is subject to change without notice.
• VIERA Connect
services through VIERA Connect are operated by their respective service providers, and service may be discontinued
• The
either temporarily or permanently without notice. Therefore, Panasonic will make no warranty for the content or the
continuity of the services.
content may be inappropriate for some viewers.
• Some
content may only be available for specific countries and may be presented in specific languages.
• Some
on the connection environment, the internet connection may be slow or may not be successful.
• Depending
the operation, audio signal is output from AV1, AUDIO OUT, DIGITAL AUDIO OUT and HDMI2 (ARC function) terminals.
• During
But no video signals are output. AV1 can output audio signal if [AV1 out] is set to [Monitor] in the Setup Menu (p. 34). To use
Using Network Services (DLNA / VIERA Connect)
You can access VIERA Connect and enjoy various network contents.
VIERA Connect requires a broadband internet connection. Dial-up internet connections cannot be used.
Ensure the network connections and network settings are completed. “Network connections” (p. 70), [Network Setup]
(p. 71 - 75)
For details about VIERA Connect operation “Using “VIERA Connect”” (p. 16)
HDMI2 with ARC function, connect an amplifier that has ARC function (p. 81) and set to use theatre speakers (p. 88).
can restrict access to VIERA Connect [Child Lock] (p. 46)
• You
• Turn the TV off, and then on again when changing or reconnecting the network connection.
79
Link Functions (Q-Link / VIERA Link)
Q-Link connects the TV and DVD Recorder / VCR, and enables easy recording, playback, etc.
(p. 82)
VIERA Link (HDAVI Control™) connects the TV and the equipment with VIERA Link function, and enables easy control,
convenient recording, playback, energy saving, creating home theatre, etc., without complicated setting. (p. 83 - 88)
You can use Q-Link and VIERA Link functions together.
This TV supports “HDAVI Control 5” function. But available features are depending on the connected equipment’s version of
HDAVI Control. Please refer to the manual of the equipment to confirm the version.
VIERA Link features may be available even with other manufacturers’ equipment supporting HDMI CEC.
•
•
Summary of Q-Link and VIERA Link features
Q-Link (SCART connection)
Connection
Connected equipment
DVD Recorder / VCR
with Q-Link function
Features
Preset download
Easy playback
Power on link
Power off link
Direct TV Recording
SCART cable
DVD Recorder / VCR
with Q-Link function
fully wired SCART cable.
• Use
the DVD Recorder / VCR supporting Q-Link to the TV’s AV1
• Connect
terminal via a SCART cable.
VIERA Link (HDMI connection)
Connected equipment
Link Functions (Q-Link / VIERA Link)
80
Features
Preset download
Easy playback
Power on link
Power off link
Reduce unnecessary power consumption
in standby
Auto standby for unnecessary equipment
Pause Live TV programme
Direct TV Recording
Control the menu of the connected
equipment by VIERA remote control
Speaker control
DIGA Recorder with
VIERA Link function
∗2 ∗5
DVD Player / Blu-ray Disc
Player with VIERA Link
function
–
∗3
∗3
–
∗3
∗2 ∗4
∗2
∗3
–
–
–
–
–
∗1
–
HD Video Camera /
LUMIX Camera with
VIERA Link function
–
∗1
–
∗1
–
Connection
HDMI cable
DIGA Recorder / DVD Player /
Blu-ray Disc Player /
HD Video Camera / LUMIX Camera
with VIERA Link function
fully wired HDMI compliant cable.
• Use
the equipment supporting VIERA Link to the TV’s HDMI1, HDMI2, HDMI3 or HDMI4 terminal via an HDMI cable.
• Connect
• About HDMI cable for connecting Panasonic HD Video Camera or LUMIX Camera, read the manual of the equipment.
VIERA Link (HDMI and Audio out connections)
Connected equipment
Features
Preset download
Easy playback
Power on link
Power off link
Reduce unnecessary power consumption
in standby
Auto standby for unnecessary equipment
Pause Live TV programme
Direct TV Recording
Control the menu of the connected
equipment by VIERA remote control
Speaker control
Player theatre with
VIERA Link function
–
∗6
Blu-ray Disc theatre with
VIERA Link function
–
∗6
Amplifier with VIERA Link
function
–
–
–
∗3
–
∗3 ∗7
–
∗3 ∗7
–
–
–
–
∗1
∗3
–
–
∗1
–
• To use Player theatre / Blu-ray Disc theatre :
Connection
Speaker system
HDMI cable
Optical digital
audio cable
or
HDMI
cable
RCA cable
or
SCART cable
Player theatre / Blu-ray Disc
theatre with VIERA Link function
• To use Amplifier :
Amplifier with
VIERA Link function
Speaker system
HDMI cable
DIGA Recorder with
VIERA Link function
∗8
SCART cable
HD Video Camera / LUMIX Camera with VIERA Link function
∗1 : Available with the equipment which has “HDAVI Control 2 or
later” function.
∗2 : Available with the equipment which has “HDAVI Control 3 or
later” function.
∗3 : Available with the equipment which has “HDAVI Control 4 or
later” function.
∗4 : Available with DIGA Recorder which has HDD.
∗5 : This function is available regardless of the version of HDAVI
Control when the recorder supports Q-Link and is connected
via SCART cable.
∗6 : While playing a disc
∗7 : Except for watching a disc
∗8 : If the connected equipment has “HDAVI Control 5”
function, you do not have to use this audio cable
(Optical digital audio cable, RCA cable or SCART
cable). In this case, connect the equipment to the TV’s
HDMI2 terminal via an HDMI cable.
VIERA Link Control of compatible equipment ([VIERA Link Control]
Link Functions (Q-Link / VIERA Link)
fully wired HDMI compliant cable.
• Use
the equipment supporting VIERA Link to the TV’s HDMI2, HDMI3 or HDMI4 terminal via an HDMI cable.
• Connect
fully wired SCART cable.
• Use
you use a SCART cable for audio output, connect the equipment supporting VIERA Link to the TV’s AV1 terminal and set
• If[AV1
out] to [Monitor] in the Setup Menu (p. 34).
• Use the optical digital audio cable, RCA cable or SCART cable for audio output from the TV.
p. 86)
below displays maximum number of compatible equipment that can be controlled by VIERA Link Control.
• Table
This includes connections to equipment already connected to the TV.
For example, DIGA Recorder connected to Amplifier which is connected to the TV via an HDMI cable.
Type of the equipment
Maximum number
Recorder (DIGA Recorder, etc.)
3
Player (DVD Player, Blu-ray Disc Player, HD Video Camera, LUMIX Camera, Digital Camera, Player
theatre, Blu-ray Disc theatre, etc.)
3
Audio system (Player theatre, Blu-ray Disc theatre, Amplifier, etc.)
1
Tuner (Set top box, etc.)
4
81
Q-Link
Preparations
the DVD Recorder / VCR with the following logos :
• Connect
“Q-Link”, “NEXTVIEWLINK”, “DATA LOGIC (a trademark of Metz Corporation)”, “Easy Link (a trademark of Philips Corporation)”,
“Megalogic (a trademark of Grundig Corporation)”, “SMARTLINK (a trademark of Sony Corporation)”
connection (p. 80)
• Q-Link
fully wired SCART cable.
• Use
up the DVD Recorder / VCR. Read the manual of the recorder.
• Set
terminal setup in the Setup Menu [AV1 out] (p. 34)
• Q-Link
• Download preset - channel, language, country settings “Preset download” (see below)
Features available
Preset download
Channel, language, country settings can be downloaded to the recorder.
DVB-C channel settings cannot be downloaded.
To download settings
[Download] (p. 34) or [Auto Setup] (p. 38) or “Auto Setup” - when first using the TV (p. 12, 13)
•
•
Direct TV Recording - What you see is What you record
Recording the current programme in DVD Recorder / VCR immediately.
Available conditions :
•
Picture source
DIRECT TV REC
DIRECT TV REC
Analogue
EXIT
Recording from
TV
TV monitor out
AV
Recorder’s tuner
IDE
GU
DVB
TV
TV monitor out
AV (watching recorder’s tuner)
AV
Recorder’s tuner
AV (watching recorder’s external input)
AV
Recorder’s
external input
AV (watching TV’s external input)
AV
TV monitor out
•
•
•
When Direct TV Recording is performed, the recorder is automatically turned on if it is in
Standby mode.
Changing channel or turning off the TV is available while the recorder is recording from its
own tuner.
Changing channel is not available while the recorder is recording from the TV tuner.
Unlock the tuner
IDE
GU
Link Functions (Q-Link / VIERA Link)
■ To stop recording
Mode
EXIT
Tuner Locked
Press EXIT to unlock and stop recording
Power on link and Easy playback
Set Power on Link [On] in the Setup Menu to use this function [Power on Link] (p. 34)
When DVD Recorder / VCR starts playback or direct navigator / function menu for the equipment are activated, the TV is turned
on and input mode is switched automatically so that you can view the content. (Only when the TV is in Standby mode.)
Power off link
Set Power off Link [On] in the Setup Menu to use this function [Power off Link] (p. 34)
When TV is set to Standby mode, the recorder is also automatically set to Standby. (Only when the videocassette or disc is not
active.)
This function will work even if the TV enters Standby mode automatically by auto power standby function.
•
Note
• Some recorders are not applicable. Read the manual of the recorder.
82
VIERA Link “
”∗
∗Enjoy additional HDMI Inter-Operability with Panasonic products which have “HDAVI Control” function.
This TV supports “HDAVI Control 5” function.
Connections to the equipment (DIGA Recorder, HD Video Camera, Player theatre, Amplifier, etc.) with HDMI and SCART cables
allow you to interface them automatically (p. 80, 81).
These features are limited to models incorporating “HDAVI Control” and “VIERA Link”.
Some functions are not available depending on the equipment’s version of HDAVI Control. Please confirm the connected
equipment’s version of HDAVI Control.
VIERA Link “HDAVI Control”, based on the control functions provided by HDMI which is an industry standard known as HDMI
CEC (Consumer Electronics Control), is a unique function that we have developed and added.
As such, its operation with other manufacturers’ equipment that supports HDMI CEC cannot be guaranteed.
Please refer to individual manuals for other manufacturers’ equipment supporting VIERA Link function.
About applicable Panasonic equipment, consult your local Panasonic dealer.
•
•
•
•
Preparations
the equipment supporting VIERA Link.
• Connect
Link connection (p. 80, 81)
• VIERA
fully wired HDMI compliant cable. Non-HDMI-compliant cables cannot be utilized.
• Use
Recommended Panasonic’s HDMI cable part number :
• RP-CDHS15 (1.5 m)
• RP-CDHS30 (3.0 m)
• RP-CDHS50 (5.0 m)
fully wired SCART cable.
• Use
up the connected equipment. Read the manual of the equipment.
• Set
optimal recording, the settings of the recorder may need to be changed. For details, read the manual of the recorder.
• For
preset - channel, language, country / region settings “Preset download” (see below)
• Download
[VIERA Link] [On] in the Setup Menu [VIERA Link] (p. 34)
• Set
up the TV
• Set After
connection, turn the equipment on and then switch the TV on.
Select the input mode to HDMI1, HDMI2, HDMI3 or HDMI4 (p. 26), and make sure that an image is displayed
correctly.
This setup should be done each time when the following conditions occur :
• for the first time
• when adding or reconnecting equipment
• when changing setup
Channel, language, country / region settings can be downloaded to the recorder.
DVB-C channel settings cannot be downloaded.
To download settings
[Download] (p. 34) or [Auto Setup] (p. 38) or “Auto Setup” - when first using the TV (p. 12, 13)
•
•
Easy playback
Automatic input switching - When the connected equipment is operated, input mode is switched automatically. When it is
stopped operating, input mode is returned.
Power on link
Set Power on Link [On] in the Setup Menu to use this function [Power on Link] (p. 34)
When the connected equipment starts playback or direct navigator / function menu for the equipment are activated, the TV is
automatically turned on. (Only when the TV is in Standby mode.)
Link Functions (Q-Link / VIERA Link)
Features available
Preset download
Power off link
Set Power off Link [On] in the Setup Menu to use this function [Power off Link] (p. 34)
When the TV is set to Standby mode, the connected equipment is also automatically set to Standby.
This function will work even if the TV enters Standby mode automatically by auto power standby function.
•
83
Reduce unnecessary power consumption in standby [Standby Power Save]
Set Standby Power Save [On] in the Setup Menu to use this function [Standby Power Save] (p. 34)
The power consumption in Standby mode of the connected equipment is controlled higher or lower in synchronization with
the TV On / Off state to reduce the consumption.
When the TV is set to Standby mode, the connected equipment is automatically set to Standby and the power consumption in
Standby mode of the connected equipment is automatically minimised.
When the TV is turned on, the connected equipment is still in Standby mode, but the power consumption is increased to make
startup time early.
This function is effective if the connected equipment can change the power consumption in Standby mode and is set to
higher consumption.
This function will work when [Power off Link] is set to [On].
•
•
Auto standby for unnecessary equipment [Intelligent Auto Standby]
Set Intelligent Auto Standby [On (With reminder)] or [On (No reminder)] in the Setup Menu to use this function
[Intelligent Auto Standby] (p. 34)
When the TV is On, non-watched or non-used connected equipment goes into Standby mode automatically to reduce the
power consumption. For example, when the input mode is switched from HDMI, when Speaker Selection is changed to [TV]
(except for watching a disc).
If you select [On (With reminder)], the on screen message will be displayed to be noticed before working this function.
This function may not work properly depending on the connected equipment. If required, set to [Off ].
•
•
Direct TV Recording - What you see is What you record [Direct TV Rec]
Recording the current programme in DIGA Recorder immediately.
If you connect a variety of recorders including other manufacturers’ recorders at the same time, please connect DIGA
Recorder to the TV’s lower HDMI terminal number. For example, if you use HDMI1 and HDMI2 for two recorders, in this case
connect DIGA Recorder to HDMI1.
If you cannot operate, check the settings and the equipment
“Summary of Q-Link and VIERA Link features” (p. 80, 81), “Preparations” (p. 83)
If you wish to record the programme which DIGA Recorder does not support, SCART connection is required and the
programme is recorded by Q-Link function (p. 82).
Depending on the programme, SCART connection may be required to record.
Changing channel or turning off the TV is available while the recorder is recording from its own tuner.
Changing channel is not available while the recorder is recording from the TV tuner.
•
•
•
•
•
•
Link Functions (Q-Link / VIERA Link)
1
Display [VIERA Link Menu]
2
Select [Direct TV Rec] and start recording
select
VIERA Link Menu
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
Start
Start
Recorder
Home Cinema
■ To stop recording
Select [Stop] in [Direct TV Rec]
select
VIERA Link Menu
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
Start
Stop
Recorder
Home Cinema
access / store
• You can also stop recording directly.
Unlock the tuner
IDE
GU
84
EXIT
Tuner Locked
Press EXIT to unlock and stop recording
start
•
You can also start recording directly.
DIRECT TV REC
Pause Live TV programme [Pause Live TV]
You can pause the live TV programme and resume later.
Live TV programme will be recorded on HDD of the connected DIGA Recorder.
This function is available with DIGA Recorder which has HDD.
If you connect a variety of recorders including other manufacturers’ recorders at the same time, please connect DIGA
Recorder which has HDD to the TV’s lower HDMI terminal number. For example, if you use HDMI1 and HDMI2 for two
recorders, in this case connect DIGA Recorder which has HDD to HDMI1.
If you cannot operate, check the settings and the equipment
“Summary of Q-Link and VIERA Link features” (p. 80, 81), “Preparations” (p. 83)
•
•
•
1
Display [VIERA Link Menu]
2
Select [Pause Live TV] and pause
The TV picture will be paused.
select
VIERA Link Menu
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
Start
Start
Recorder
Home Cinema
pause
TV programme is recorded on HDD from where it was paused.
• Live
• If the paused TV picture disappears after a few minutes.
OPTION
(The paused picture will be restored)
• Follow the operation guide to operate Pause Live TV function.
may be different depending on the recorder. In this case,
• Operations
follow the operation guide or read the manual of the recorder.
search backward
pause
search forward
playback
stop
If you stop playback, the recorded
programme will be deleted from
HDD.
•
■ To return to Live TV
(Stop playback of Pause Live TV / cancel pause)
Select [Yes]
Pause Live TV
TV
select
stop
Stop Pause Live TV?
Yes
Link Functions (Q-Link / VIERA Link)
■ To operate Pause Live TV
No
• If you stop playback or cancel pause, the recorded programme will be deleted from HDD.
85
Control the menu of the connected equipment by VIERA remote control
[VIERA Link Control]
You can control some functions of the connected equipment with this TV remote control (point the remote control at the TV’s
signal receiver).
If you cannot operate, check the settings and the equipment
“Summary of Q-Link and VIERA Link features” (p. 80, 81), “Preparations” (p. 83)
For details of the operations for the connected equipment, read the manual of the equipment.
•
•
1
Display [VIERA Link Menu]
2
Select [VIERA Link Control]
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
3
select
VIERA Link Menu
Start
Start
Recorder
Home Cinema
access
Select the equipment you want to access
The type of the connected equipment is displayed.
Select the type of the equipment and access.
select
VIERA Link Menu
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
Start
Start
Recorder
Home Cinema
store
[Recorder] / [Player] / [Home Cinema] / [Video Camera] / [LUMIX] /
[Digital Camera] / [Other]
Link Functions (Q-Link / VIERA Link)
86
can also access directly by using VIERA TOOLS
• You “How
to Use VIERA TOOLS” (p. 28)
displayed item may vary depending on the connected equipment.
• The
Cinema] means Player theatre, Blu-ray Disc theatre or Recorder theatre.
• [Home
• [Other] means Tuner set top box.
The menu of the accessed equipment
(Input mode will be changed automatically)
TV
4
Operate the menu of the equipment
Available VIERA remote control buttons :
(Depending on the connected equipment)
1 Set the position to “TV”
DVD/VCR
TV
2 Follow the operation guide
• To display the operation guide
OPTION
If other manufacturers’ equipment is accessed, Setup / Contents Selection menu may be
displayed.
• When the key words are displayed on colour bar
(red)
(green)
(yellow)
(blue)
Note
operations may not be available depending on the equipment. In this case use its own
• Some
remote control to operate the equipment.
TV
■ If multiple recorders or players are connected
VIERA Link Menu
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
Start
Start
Recorder2
Home Cinema
The number is given from the TV’s lower HDMI terminal number connected to the
same type equipment. For example, two recorders to HDMI2 and HDMI3, in this
case the recorder connected to HDMI2 is displayed as [Recorder1], and the recorder
connected to HDMI3 is displayed as [Recorder2].
[Recorder1-3 / Player1-3]
VIERA Link Menu
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
Start
Start
Recorder
Home Cinema
The type of the connected equipment is displayed.
You can access the menu of the equipment. But you cannot operate it. Use its own
remote control to operate the equipment.
Link Functions (Q-Link / VIERA Link)
■ If you access non-VIERA Link equipment
87
Speaker control [Speaker Selection]
You can control the theatre speaker with this TV remote control (point the remote control at the TV’s signal receiver).
If you cannot operate, check the settings and the equipment
“Summary of Q-Link and VIERA Link features” (p. 80, 81), “Preparations” (p. 83)
•
1
Display [VIERA Link Menu]
2
Select [Speaker Selection]
Pause Live TV
Direct TV Rec
VIERA Link Control
Speaker Selection
3
select
VIERA Link Menu
Start
Start
Recorder
Home Cinema
access
Set to [Home Cinema] or [TV]
select
store
[Home Cinema]
Player theatre, Blu-ray Disc theatre or Amplifier will be automatically turned on if it is in
Standby mode and the sound is from theatre speakers connected to the equipment.
• Volume up / down
• Mute
Link Functions (Q-Link / VIERA Link)
sound of TV speakers is mute.
• The
• When the equipment is turned off, TV speakers will be active.
TV
[TV]
TV speakers are active.
Multi-channel sound
If you wish to enjoy the multi-channel sound (e.g. Dolby Digital 5.1ch) via an Amplifier, connect
with HDMI cable and Optical digital audio cable (p. 81), and then select [Home Cinema]. If your
Amplifier has “HDAVI Control 5” function, you can connect only with HDMI cable. In this case,
connect your Amplifier to the TV’s HDMI2 terminal.
To enjoy the sound from the DIGA Recorder in multi-channel sound, connect an HDMI cable from
the DIGA Recorder to the Amplifier (p. 81).
Note
functions may not work properly depending on the connected equipment.
• These
or sound may not be available for the first few seconds when input mode is switched.
• Image
playback may be available by using the remote control for Player theatre, Blu-ray Disc theatre or Amplifier. Read the
• Easy
manual of the equipment.
Control 5” is the newest standard (current as of December, 2010) for HDAVI Control compatible equipment. This
• “HDAVI
standard is compatible with conventional HDAVI equipment.
• To confirm this TV’s version of HDAVI Control [System Information] (p. 36)
88
External Equipment
These diagrams show our recommendations for connection of your TV to various pieces of equipment.
For other connections, consult the instructions for each piece of equipment, the table below, and the specifications (p. 102,
103).
To record / playback
Terrestrial aerial
or
RF cable
DVD Recorder / VCR
Fully wired SCART cable
To watch satellite broadcasts
Fully wired
SCART cable
Fully wired HDMI
compliant cable
Set top box
(Listening)
DVD Player
External Equipment
To watch DVDs
(Viewing)
HDMI equipment
Rear of the TV
Recorder / Player
Fully wired HDMI
compliant cable
• HDMI connection
(p. 96)
Camcorder
89
Network (wired)
Internet
Modem
LAN cable (Shielded)
Hub or Router
USB devices
Wireless LAN Adaptor
USB cable
USB HDD
PC
(Viewing)
Conversion adaptor
(if necessary)
(Listening)
Computer
External Equipment
To listen with speakers
Optical digital audio cable
or
RCA cable
Amplifier with
speaker system
Rear of the TV
To enjoy the sound from the external equipment in
multi-channel sound (e.g. Dolby Digital 5.1ch), connect the
equipment to the amplifier.
For the connections, read the manuals of the equipment and
amplifier.
90
Camcorder / Game equipment
Side panel of
the TV
(Viewing)
Camcorder
(Listening)
Game equipment
Headphones
(M3 stereo mini plug)
adjust volume
• To [Headphone
Volume] (p. 32)
Types of connectable equipment to each terminal
Terminal
USB 1 - 3
HDMI 1 - 4
ETHERNET
DIGITAL
AUDIO OUT
AUDIO OUT
COMPONENT
AV2
AV1
Recording / Playback
(equipment)
External Equipment
To record / playback videocassettes / DVDs
(VCR / DVD Recorder)
∗1
To watch satellite broadcasts (Set top box)
To watch DVDs (DVD Player)
To watch camcorder images (Video camera)
To play games (Game equipment)
∗2
To use amplifier with speaker system
To use network services
∗3
USB HDD Recording
Q-Link
VIERA Link
(with HDMI)
Direct TV Recording
: Recommended Connection
∗1 : Use HDMI1 for automatic input switching.
∗2 : Use HDMI2 for connecting an amplifier. This connection is applicable when using an amplifier that has ARC (Audio Return
Channel) function.
∗3 : Use USB 1 port for connecting the USB HDD.
91
Technical Information
Auto Aspect
The optimum size and aspect can be chosen automatically, and you can enjoy finer images.
(p. 20)
Aspect Control Signal
[WIDE] will appear in the top left of the screen if a Widescreen signal (WSS) or a Control signal through SCART / HDMI terminal
is found.
The aspect will switch to the appropriate 16:9 or 14:9 widescreen ratio.
This function will work in any aspect mode.
Aspect Control Signal
Input terminal
Cable
RF
AV1 / AV2
(Composite)
COMPONENT
Technical Information
HDMI1
HDMI2
HDMI3
HDMI4
Input signal format
DVB-C
DVB-T
PAL B, G, H, I
PAL D, K
SECAM B, G
SECAM L, L’
SECAM D, K
PAL 525/60 6.5 MHz
PAL 525/60 6.0 MHz
PAL 525/60 5.5 MHz
M.NTSC 6.5 MHz
M.NTSC 6.0 MHz
M.NTSC 5.5 MHz
PAL
SECAM
PAL 525/60
M.NTSC
NTSC
525 (480) / 60i, 60p
625 (576) / 50i, 50p
750 (720) / 60p, 50p
1,125 (1,080) / 60i, 50i
525 (480) / 60i, 60p
625 (576) / 50i, 50p
750 (720) / 60p, 50p
1,125 (1,080) / 60i, 50i
1,125 (1,080) / 60p, 50p, 24p
Widescreen signal
(WSS)
Control signal
through SCART (pin8) /
HDMI terminal
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Auto mode
Auto mode determines the best aspect ratio to fill the screen. It does this using a four step process (WSS, Control signal
through SCART / HDMI terminal, Letterbox detection or Justify to fill the screen) to determine.
This process may take several minutes, depending on the darkness of the image.
Letterbox detection :
If black bands at the top and bottom of the screen are detected, Auto mode chooses the best ratio and expands the image to
fill the screen.
If no aspect signals are detected, Auto mode enhances the image for optimum viewing pleasure.
Note
ratio varies depending on the programme, etc. If the ratio is out of the standard 16:9, black bands at the top and bottom
• The
of the screen may appear.
the screen size looks unusual when a widescreen-recorded programme is played back on a VCR, adjust the tracking of the
• IfVCR.
Read the manual of the VCR.
92
Supported file format in Media Player and media servers
■ Photo
Format
JPEG
File extension
.jpg
Image resolution
(pixel)
8×8
to
30,719 × 17,279
Details / Restrictions
DCF∗ and EXIF∗ standards
Sub-sampling : 4:4:4, 4:2:2, 4:2:0
Progressive JPEG is not supported.
1
2
•
∗1 : Design rule for Camera File system - unified standard established by Japan Electronics and Information Technology
Industries Association (JEITA)
∗2 : Exchangeable Image File - image file format used by digital cameras
■ Video
Container
File extension
Video codec
Audio codec
Details / Restrictions
SD-Video Standard Ver. 1.3
(Entertainment Video Profile)
The data may not be available if a folder
structure on the device is modified.
SD-Video
.mod
MPEG1
MPEG2
MPEG
Dolby Digital
•
AVCHD
.mts
H.264
Dolby Digital
data may not be available if a folder
• The
structure on the device is modified.
AVI
.avi
.divx
DIV3
DIV4
DIVX
DX50
DIV6
XviD
MPEG4 SP / ASP
MPEG
MP3
Dolby Digital
H.264 BP / MP / HP
MPEG
MP3
Dolby Digital
DTS core
AVCHD Standard
MKV
.mkv
ASF
.asf
.wmv
Windows Media
Video Ver. 9
WMA
VC-1
to play DivX Plus HD video file
• Certified
in Media Player
For details of DivX
“DivX” (p. 94)
files cannot be played
• Copy-protected
back.
Pro and WMA Lossless are not
• WMA
supported.
TV supports this container recorded
• This
by Panasonic products.
.mp4
H.264 BP / MP / HP
AAC
MP3
Dolby Digital
MOV
.mov
MotionJPEG
H.264 BP / MP / HP
Linear PCM (RAW /
TWOS / SOWT)
AAC
MP3
Dolby Digital
TV supports Motion JPEG recorded
• This
by Panasonic LUMIX Camera∗ .
TV is not available for playing back
• This
Motion JPEG with the media server.
PS
.mpg
.mpeg
MPEG1
MPEG2
MPEG
MP3
Linear PCM
–
TS
.ts
.tp
MPEG2
H.264
AAC
MP3
Dolby Digital
Dolby Digital Plus
HE-AAC
container can be played back only
• This
with the media server.
MP4
For details, read the manual of the
products.
3
Technical Information
∗3 : Some products of before the year 2004 may not be available. The compatibility with future products is not guaranteed.
93
■ Music
Codec
File extension
MP3
.mp3
AAC
.m4a
WMA
.wma
Restrictions
–
• Copy-protected files cannot be played back.
files cannot be played back.
• Copy-protected
• WMA Pro and WMA Lossless are not supported.
Note
files may not be played back even if they fulfill these conditions.
• Some
not use two-byte characters or other special codes for data.
• Do
• The device may become unusable with this TV if the file or folder names are changed.
DivX
DivX Certified® to play DivX® and DivX Plus™ HD (H.264/MKV) video up to 1080p HD including premium content.
ABOUT DIVX VIDEO :
DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified® device that plays DivX video.
Visit divx.com for more information and software tools to convert your files into DivX video.
Subtitle text file of DivX
Subtitles format - MicroDVD, SubRip, TMPlayer
The DivX video file and subtitles text file are inside the same folder, and the file names are the same except for the file
extensions.
If there are more than one subtitles text files inside the same folder, they are displayed in the following order of priority :
“.srt”, “.sub”, “.txt”.
To confirm or change the current subtitle status while playing DivX content, press the OPTION button to display Option
Menu.
Depending on the methods used to create the file or the state of recording, only parts of the subtitles may be displayed, or
the subtitles may not be displayed at all.
•
•
•
•
Note
on how you make SD Card, USB Flash Memory or the media server, files and folders may not be displayed in the
• Depending
order you numbered.
on how you create the files and the structure of folders, the files and folders may not be displayed.
• Depending
• When there are many files and folders, operation may take time to complete or some files may not be displayed or playable.
ABOUT DIVX VIDEO-ON-DEMAND :
This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain
your registration code, locate the DivX VOD section in the Setup Menu. Go to vod.divx.com for more information on how to
complete your registration.
To show DivX VOD registration code
[DivX® VOD] in the Setup Menu (p. 36)
you want to generate the new registration code, you have to deregister the present registration code.
• IfAfter
playing DivX VOD content once, the confirmation screen to deregister will be displayed in [DivX® VOD] in the Setup
Technical Information
94
•
Menu. If you press the OK button on the confirmation screen, the deregistration code will be generated and you will not be
able to play any contents that you purchased using the present registration code.
You will obtain the new registration code by pressing the OK button on the deregistration code screen.
If you purchase DivX VOD content using a registration code different from this TV’s code, you will not be able to play this
content. ([Your device is not authorized to play this DivX protected video.] is displayed.)
Regarding DivX content that can only be played a set number of times
Some DivX VOD content can only be played a set number of times.
When you play this content, the remaining number of plays is displayed. You cannot play this content when the number of
remaining plays is zero. ([This DivX rental has expired.] is displayed.)
When playing this content, the number of remaining plays is reduced by one in the following conditions :
• If you exit the current application.
• If you play the other content.
• If you go to the next or previous content.
•
Devices for recording or playing back
■ SD Card (for playing back in Media Player)
Card format : SDXC Card - exFAT
SDHC Card / SD Card - FAT16 or FAT32
Compliant card type (maximum capacity) : SDXC Card (64 GB), SDHC Card (32 GB), SD Card (2 GB),
miniSD Card (2 GB) (requiring miniSD adaptor)
If miniSD Card is used, insert / remove it together with the adaptor.
Check the latest information on the card type at the following website. (English only)
http://panasonic.jp/support/global/cs/tv/
Use an SD Card which meets SD standards. If not, it may cause the TV to malfunction.
•
•
•
2.1 mm
32 mm
24 mm
■ USB Flash Memory (for playing back in Media Player)
USB Flash Memory format : FAT16, FAT32 or exFAT
A USB HDD formatted by PC is not supported in Media Player.
•
■ USB HDD (for recording the digital TV programmes with this TV and playing back in Media Player)
The capacity of USB HDD that have been tested for the performance with this TV : From 160 GB to 3 TB
Connect the USB HDD to the socket outlet to record and play back properly with this TV.
Format the USB HDD with this TV in order to use it. (p. 53)
Regarding the performance, not all USB HDDs are guaranteed. Check the USB HDDs that have been tested for the
performance with this TV at the following website. (English only)
http://panasonic.jp/support/global/cs/tv/
•
•
•
Note
modified with a PC may not be displayed.
• Data
not remove the device while the TV is accessing data (this can damage device or TV).
• Do
not touch the pins on the device.
• Do
not subject the device to a high pressure or impact.
• Do
the device in the correct direction (otherwise, device may be damaged).
• Insert
interference, static electricity, or erroneous operation may damage the data or device.
• Electrical
up the recorded data at regular intervals in case of deteriorated or damaged data or erratic operation of the TV.
• Back
(Panasonic is not liable for any deterioration or damage of recorded data.)
SCART and HDMI terminal information
AV1 SCART terminal (RGB, VIDEO, Q-Link)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
RGB status earth
Status RGB
Earth
-Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
18
16
14
12
10
8
6
4
2
+5V Power
SDA
Utility
TMDS Clock−
TMDS Clock+
TMDS Data0 Shield
TMDS Data1−
TMDS Data1+
TMDS Data2 Shield
HDMI terminal
Hot Plug Detect
DDC/CEC Ground
SCL
CEC
TMDS Clock Shield
TMDS Data0−
TMDS Data0+
TMDS Data1 Shield
TMDS Data2−
TMDS Data2+
19
17
15
13
11
9
7
5
3
1
Technical Information
Socket Earth
CVBS out (video)
CVBS earth
Red in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Audio out (R)
95
HDMI connection
HDMI (high-definition multimedia interface) is the world’s first complete digital consumer AV interface complying with a noncompression standard.
HDMI allows you to enjoy high-definition digital images and high-quality sound by connecting the TV and the equipment.
HDMI-compatible equipment∗1 with an HDMI or DVI output terminal, such as a DVD player, a set top box or a game
equipment, can be connected to the HDMI terminal using an HDMI compliant (fully wired) cable.
About connections, see “External Equipment” (p. 89).
Applicable HDMI features
audio signal :
• Input
2ch Linear PCM (sampling frequencies - 48 kHz, 44.1 kHz, 32 kHz)
video signal :
• Input
480i, 480p, 576i, 576p, 720p, 1080i and 1080p
•
Link (HDAVI Control 5)
• VIERA
[VIERA Link] (p. 83)
Type
• Content
Colour
• Deep
Return Channel∗
• Audio
(HDMI2 terminal only)
2
“Input signal that can be displayed” (p. 98)
Match the output setting of the digital equipment.
Input PC signal :
“Input signal that can be displayed” (p. 98)
Match the output setting of the PC.
DVI connection
If the external equipment has only a DVI output, connect to the HDMI terminal via a DVI to HDMI adaptor cable∗3. When the
DVI to HDMI adaptor cable is used, connect the audio cable to the audio input terminal (HDMI1 / 2 / 3 : use AUDIO IN terminals
/ HDMI4 : use AV2 audio terminals).
Note
settings can be made on the [HDMI1 / 2 / 3 / 4 Input] in the Sound Menu. (p. 33)
• Audio
the connected equipment has an aspect adjustment function, set the aspect ratio to “16:9”.
• IfThese
connectors are “type A”.
• These HDMI
HDMI connectors are compatible with HDCP (High-Bandwidth Digital Content Protection) copyright protection.
• Equipment
having no digital output terminal may be connected to the input terminal of “COMPONENT” or “VIDEO” to receive
• analogue signals.
• This TV incorporates HDMI™ technology.
∗1 : The HDMI logo is displayed on HDMI-compliant equipment.
∗2 : Audio Return Channel (ARC) is a function to be able to send digital sound signals via an HDMI cable.
∗3 : Enquire at your local digital equipment retailer shop.
PC connection
A PC may be connected to this TV so that the PC screen is displayed and sound is heard from the TV.
PC signals that can be input : Horizontal scanning frequency 31 to 69 kHz; vertical scanning frequency 59 to 86 Hz (more than
1,024 signal lines could result in incorrect display of the image).
A PC adaptor is not necessary for the DOS/V-compliant D-sub 15-pin connector.
•
•
Note
Technical Information
96
PC models cannot be connected to this TV.
• Some
• Max. display resolution
using PC, set the colour display quality of PC to the
• When
4:3
1,440 × 1,080 pixels
highest position.
16:9
1,920 × 1,080 pixels
details of the applicable PC signals
• For
• “Input signal that can be displayed” (p. 98)
• D-sub 15-pin connector signal
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
R
GND (Ground)
NC (not connected)
G
GND (Ground)
NC (not connected)
B
GND (Ground)
HD
NC (not connected)
NC (not connected)
VD
GND (Ground)
GND (Ground)
NC (not connected)
USB connection
•
•
•
•
•
It is recommended to connect the USB HDD or USB Flash Memory directly to the TV’s USB ports.
Some USB devices or USB HUB may not be used with this TV.
You cannot connect any devices by using USB card reader.
You cannot use two or more same kind of USB devices simultaneously except USB Flash Memory or USB HDD.
Additional information for USB devices may be on the following website. (English only)
http://panasonic.jp/support/global/cs/tv/
USB Keyboard
USB Keyboard which requires the driver is not supported.
• The
change the language type [USB Keyboard Layout] (p. 36)
• ToCharacters
• setting. may not be displayed correctly on the TV screen depending on the connected keyboard or the keyboard layout
• Some of the keys of USB keyboards may correspond to the operation of the remote control.
USB Keyboard
Remote Control
↑/↓/←/→
USB Keyboard
Cursor buttons
Remote Control
F2
VIERA TOOLS
Enter
OK
F3
MENU
Backspace
BACK/RETURN
F4
INPUT (AV)
Esc
EXIT
F5 / F6
Channel Down / Up
0 - 9 / Character
Numeric buttons
F7 / F8
Volume Down / Up
F1
GUIDE
F9 / F10 / F11 / F12
Coloured buttons
Gamepad
the gamepads that have been tested for the performance with this TV at the following website. (English only)
• Check
http://panasonic.jp/support/global/cs/tv/
• Some of the keys of gamepads correspond to the operation of the remote control.
Example :
1
2
Select
3
4
5
Start
11 10 9
8 7 6
1
2
3
4
5
Remote Control
Volume Up / Down
Channel Up / Down
GUIDE
OK
BACK/RETURN
10
Remote Control
VIERA TOOLS
EXIT
INPUT
(AV)
MENU
6
VIERA Connect
11
Cursor buttons
7
8
9
Characters table for numeric buttons
You can enter characters by using numeric buttons for free input items.
Press the numeric button repeatedly until you reach the
User input
desired character.
Name
abc
B
C D
E
F
G H
I
J
K
L M N O
P
Q
R
S
T
V W X
Y
Z
0
1
2
3
4
5
6
7
8
9
!
:
#
a
b
c
d
e
f
g
h
i
j
k
l
m n
o
p
q
r
s
t
u
v
w
x
y
z
(
)
+
-
.
*
_
jkl
mno
tuv
wxyz
character is set automatically if you leave for 1 second.
• The
can also set the character by pressing the OK button or other
• You
numeric buttons within 1 second.
Characters table :
Numeric
buttons
The number of times to press
1
.
2
1
3
!
4
:
5
#
6
+
7
-
abc
a
b
c
def
d
e
f
2
A
B
C
3
D
E
ghi
g
h
F
i
4
G
H
jkl
j
I
k
l
5
J
K
L
mno
m
n
o
6
M
N
O
pqrs
p
q
r
s
7
P
Q
tuv
t
u
v
8
T
U
V
w
x
y
z
9
W
X
Space
0
wxyz
8
*
9
_
R
S
Y
Z
10
(
11
)
Technical Information
A
U
def
ghi
pqrs
97
Input signal that can be displayed
COMPONENT (Y, PB, PR), HDMI
Signal name
525 (480) / 60i, 60p
625 (576) / 50i, 50p
750 (720) / 60p, 50p
1,125 (1,080) / 60i, 50i
1,125 (1,080) / 60p, 50p, 24p
COMPONENT
HDMI
Mark : Applicable input signal
PC (from D-sub 15P)
Signal name
640 × 400 @70 Hz
640 × 480 @60 Hz
640 × 480 @75 Hz
800 × 600 @60 Hz
800 × 600 @75 Hz
800 × 600 @85 Hz
852 × 480 @60 Hz
1,024 × 768 @60 Hz
1,024 × 768 @70 Hz
1,024 × 768 @75 Hz
1,024 × 768 @85 Hz
1,280 × 768 @60 Hz
1,280 × 1,024 @60 Hz
1,366 × 768 @60 Hz
Macintosh13” (640 × 480)
Macintosh16” (832 × 624)
Macintosh21” (1,152 × 870)
Horizontal frequency (kHz)
Vertical frequency (Hz)
31.47
31.47
37.50
37.88
46.88
53.67
31.44
48.36
56.48
60.02
68.68
47.70
63.98
48.39
35.00
49.73
68.68
70.07
59.94
75.00
60.32
75.00
85.06
59.89
60.00
70.07
75.03
85.00
60.00
60.02
60.04
66.67
74.55
75.06
Applicable input signal for PC is basically compatible to VESA standard timing.
PC (from HDMI terminal)
Signal name
640 × 480 @60 Hz
750 (720) / 60p
1,125 (1,080) / 60p
Horizontal frequency (kHz)
31.47
45.00
67.50
Vertical frequency (Hz)
60.00
60.00
60.00
Applicable input signal for PC is basically compatible to HDMI standard timing.
Note
Technical Information
98
• Signals other than above may not be displayed properly.
• The above signals are reformatted for optimal viewing on your display.
• PC signal is magnified or compressed for display, so that it may not be possible to show fine detail with
sufficient clarity.
FAQs
Before requesting service or assistance, please follow these simple guides to resolve the problem.
If the problem still persists, please contact your local Panasonic dealer for assistance.
Block noise, frozen or disappearing image occurs in DVB mode / White spots or shadow image (ghosting) occurs in
Analogue mode / Some channels cannot be tuned
Check the position, direction and connection of the aerial.
Check [Signal Condition] (p. 41). If [Signal Quality] is displayed in red, the DVB signal is weak.
Weather conditions will affect signal reception (heavy rain, snow, etc.), in particular in poor reception areas. Even during
good weather, the high pressure can cause poor reception of some channels.
Due to the digital reception technologies involved, quality of the digital signals may be relatively low in some cases,
despite good reception of analogue channels.
Turn the TV off with the Mains power On / Off switch, and then on again.
If problem persists, consult your local dealer or service provider for the availability of services.
•
•
•
•
•
•
No programmes shown on TV Guide
the digital transmitter.
• Check
the direction of the aerial to another transmitter installed nearby.
• Adjust
• Check the analogue broadcast. If the image quality is poor, check the aerial and consult your local dealer.
Neither image nor sound is produced
the TV in AV mode?
• IsCheck
correct input mode is selected.
• Check the
mains lead is plugged into the socket outlet and the TV is turned on.
• Check the
Picture Menu (p. 30, 31) and volume.
• Check the
• all required cables and connections are firmly in place.
Auto aspect
aspect is designed to provide you with the best ratio to fill the screen. (p. 92)
• Auto
• Press the ASPECT button if you would like to change the aspect ratio manually. (p. 20)
Black and white picture
that the output of the external equipment matches the input of the TV.
• Check
When connecting with SCART, ensure the output setting of the external equipment is not S-Video.
Input mode, i.e. EC/AV1 remains on the screen
the button to clear these.
• Press
Press again to redisplay.
Q-Link function does not work
SCART cable and connection.
• Confirm
Also set [AV1 out] in the Setup Menu.
(p. 34)
•
•
Recording does not start immediately
• Check the settings of the recorder. For details, read the manual of the recorder.
There may be red, blue, green and black spots on the screen
is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel is built with very high
• This
precision technology giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a
fixed point of red, green, blue or black. Please note this does not affect the performance of your LCD.
Frequently Asked Questions
[VIERA Link] function does not work and an error message appears
Confirm the connection. (p. 80, 81)
Turn the connected equipment on and then switch the TV on. (p. 83)
99
Problem
Chaotic image, noisy
Screen
No image can be displayed
Blurry or distorted image
(no sound or low volume)
Unusual image is displayed
Sound
No sound is produced
Sound level is low or sound
is distorted
Sound is unusual
HDMI
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
Cannot connect to the
network
Network
Cannot select the file during
DLNA operations
Cannot operate
VIERA Connect
The TV does not switch On
Other
Frequently Asked Questions
100
The TV goes into Standby
mode
The remote control does not
work or is intermittent
Parts of the TV become hot
The LCD panel moves
slightly when it is pushed
with a finger
Clattered sound might be
heard
Actions
[P-NR] in the Picture Menu (to remove noise). (p. 30)
• Set
• Check nearby electrical products (car, motorcycle, fluorescent lamp).
[Brightness] or [Colour] in the Picture Menu set to the minimum?
• Is [Contrast],
(p. 30)
• Reset channels. (p. 37, 38)
the TV Off with Mains power On / Off switch, then turn it On again.
• Turn
• If the problem persists, initialise all settings [Shipping Condition] (p. 50)
mute” active? (p. 8)
• IsIs “Sound
• the volume set to the minimum?
signal reception may be deteriorated.
• Sound
• Set [MPX] (p. 32) in the Sound Menu to [Mono]. (Analogue only)
the sound setting of the connected equipment to “2ch L.PCM”.
• Set
the [HDMI1 / 2 / 3 / 4 Input] setting in the Sound Menu. (p. 33)
• Check
sound connection has a problem, select analogue sound connection.
• If digital
(p. 96)
the HDMI cable is connected properly. (p. 89)
• Check
the TV and equipment Off, then turn them On again.
• Turn
an input signal from the equipment. (p. 98)
• Check
• Use equipment compliant with EIA/CEA-861/861D.
the LAN cable or Wireless LAN Adaptor is connected properly. (p. 70)
• Check
the connections and settings. (p. 70 - 75)
• Check
the network equipment and network environment.
• Check
router may not be set to issue IP address automatically. If the network
• The
administrator prefers to allocate an IP address, set an IP address manually. (p. 72)
router may be using MAC address filtering (security setting).
• The
Confirm the MAC Address of this TV (p. 75) and set the router to be able to use it.
the problem persists, consult your Internet Service Provider or telecommunications
• Ifcompany.
media server of the connected equipment prepared? (p. 69)
• IsCheck
• applicable data format. (p. 93)
the connections and settings. (p. 70 - 75)
• Check
• The server or connected line might be busy now.
• Check the mains lead is plugged into the socket outlet.
power standby function is activated. (p. 9)
• Auto
• The TV enters Standby mode about 30 minutes after analogue broadcasting ends.
the batteries installed correctly? (p. 7)
• Are
the TV been switched On?
• Has
batteries may be running low. Replace them.
• The
the remote control directly at the front of the TV (within about 7 m and a 30
• Point
degree angle of the front of the TV).
the TV away from sunshine or other sources of bright light not to shine on
• Situate
the TV’s remote control signal receiver.
when the temperature of parts of the front, top and rear panels has risen, these
• Even
temperature rises will not pose any problems in terms of performance or quality.
is some flexibility around the panel to prevent damage to the panel.
• There
panel might move slightly when it is pushed with a finger, and clattered sound
• The
might be heard. This is not a malfunction.
Problem
Other
Overcurrent error message
appears
An error message appears
Actions
•
•
the message’s instructions.
• Follow
the problem persists, contact your local Panasonic dealer or the authorized Service
• IfCentre.
The connected USB device might cause this error. Remove the device and turn the
TV Off with Mains power On / Off switch, then turn it On again.
Check if foreign objects are inside the USB port.
Licence
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
and the DVB logos are trademarks of the DVB Project.
• DVB
is a trademark of International Business Machines Corporation.
• VGA
is a registered trademark of the Video Electronics Standard Association.
• S-VGA
is a trademark of Apple Inc.
• Macintosh
Logo is a trademark of SD-3C, LLC.
• SDXC
the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
• HDMI,
LLC in the United States and other countries.
Control™ is a trademark of Panasonic Corporation.
• HDAVI
and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
• “AVCHD”
under license from Dolby Laboratories.
• Manufactured
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and
• Manufactured
worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS 2.0+ Digital Out and the DTS
logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
Connect is a trademark of Panasonic Corporation.
• VIERA
the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living
• DLNA®,
Network Alliance.
is a registered trademark of Microsoft Corporation in the United States and other countries.
• Windows
DivX Certified®, DivX Plus™ HD and associated logos are trademarks of DivX, Inc. and are used under license.
• DivX®,
Skype name, associated trade marks and logos and the “S” symbol are trade marks of Skype Limited.
• The
and the QuickTime logo are trademarks or registered trademarks of Apple Inc., used under license therefrom.
• QuickTime
Plus+ is (1) a registered trademark or trademark of, (2) manufactured under license from and (3) subject of various
• GUIDE
international patents and patent applications owned by, or licensed to, Rovi Corporation and/or its related affiliates.
Frequently Asked Questions / Licence
101
Specifications
TX-LF32E30
AC 220-240 V, 50 / 60 Hz
Rated Power Consumption
72 W
Standby Power
Consumption
0.30 W
Dimensions (W × H × D)
Mass
769 mm × 514 mm ×
230 mm (With Pedestal)
890 mm × 582 mm ×
260 mm (With Pedestal)
1,002 mm × 646 mm ×
288 mm (With Pedestal)
769 mm × 480 mm ×
75 mm (TV only)
890 mm × 548 mm ×
75 mm (TV only)
1,002 mm × 611 mm ×
75 mm (TV only)
Display panel
12.5 k Net (With Pedestal)
15.0 k Net (With Pedestal)
19.0 k Net (With Pedestal)
10.0 k Net (TV only)
12.5 k Net (TV only)
15.5 k Net (TV only)
94 cm (diagonal)
819 mm (W) × 460 mm (H)
106 cm (diagonal)
930 mm (W) × 523 mm (H)
Sound
16:9
Visible screen size
Number of pixels
2,073,600 (1,920 (W) × 1,080(H))
Speaker
(160 mm × 42 mm) × 2, 8 Ω
Audio Output
20 W (10 W + 10 W)
Receiving Systems /
Band name
Check the latest information
on the available services at
the following website.
(English only)
http://panasonic.jp/support/
global/cs/tv/
102 W
14.00 W (With monitor out recording)
80 cm (diagonal)
698 mm (W) × 392 mm (H)
PC signals
TX-LF42E30
85 W
Aspect Ratio
Headphones
Specifications
102
TX-LF37E30
Power Source
M3 (3.5 mm) stereo mini Jack × 1
VGA, SVGA, WVGA, XGA
SXGA, WXGA ······ (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
PAL B, G, H, I,
SECAM B, G,
SECAM L, L’
VHF E2 - E12
VHF A - H (ITALY)
CATV (S01 - S05)
CATV S11 - S20 (U1 - U10)
VHF H1 - H2 (ITALY)
UHF E21 - E69
CATV S1 - S10 (M1 - M10)
CATV S21 - S41 (Hyperband)
PAL D, K,
SECAM D, K
VHF R1 - R2
VHF R6 - R12
PAL 525/60
Playback of NTSC tape from some PAL Video recorders (VCR)
M.NTSC
Playback from M.NTSC Video recorders (VCR)
VHF R3 - R5
UHF E21 - E69
NTSC (AV input only) Playback from NTSC Video recorders (VCR)
DVB-T
Digital terrestrial services (MPEG2 and MPEG4-AVC(H.264))
DVB-C
Digital cable services (MPEG2 and MPEG4-AVC(H.264))
Aerial input
VHF / UHF
Operating Conditions
Temperature : 0 °C - 35 °C
Humidity : 20 % - 80 % RH (non-condensing)
AV1 (SCART)
AV2 input
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
VIDEO
RCA PIN Type × 1
1.0 V[p-p] (75 Ω)
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
Connection Terminals
COMPONENT input
Y
PB, PR
1.0 V[p-p] (including synchronization)
±0.35 V[p-p]
HDMI 1 / 2 / 3 / 4 input
TYPE A Connectors
HDMI1 / 3 / 4 : HDMI (Version 1.4 with Content Type), Deep Colour
HDMI2 : HDMI (Version 1.4 with Content Type, Audio Return Channel), Deep Colour
This TV supports “HDAVI Control 5” function.
•
PC
HIGH-DENSITY D-SUB 15PIN
R,G,B : 0.7 V[p-p] (75 Ω)
HD, VD : TTL Level 2.0 – 5.0 V[p-p] (high impedance)
Card slot
SD Card slot × 1
Common Interface slot (complies with CI Plus) × 1
ETHERNET
RJ45, IEEE802.3 10BASE-T / 100BASE-TX
USB 1 / 2 / 3
USB2.0 DC 5 V, Max. 500 mA
AUDIO OUT
RCA PIN Type × 2
DIGITAL AUDIO OUT
PCM / Dolby Digital / DTS, Fiber optic
0.5 V[rms] (high impedance)
Note
and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
• Design
equipment complies with the EMC standards listed below.
• This
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024
Specifications
103
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with general household waste. For proper treatment,
recovery and recycling of old products and used batteries, please take them to applicable collection points,
in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples) :
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
Declaration of Conformity (DoC)
Authorized Representative :
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Customer’s Record
The model number and serial number of this product may be found on its rear panel. You should note this serial number in
the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid
in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
M0211-0
Web Site : http://panasonic.net
© Panasonic Corporation 2011
Printed in Czech Republic
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising