Panasonic | ER1510 | Operating instructions | Panasonic ER1510 Operating Instructions

Operating Instructions
AC/Rechargeable hair clipper for professional use
Model No. ER1510
English
2 Português
00 Magyar
00
Deutsch
0 Norsk
00 Română
00
00
Français
00 Svenska
00 Русский
Italiano
00 Suomi
00 Türkçe
000
Nederlands
00 Polski
00 Українська
000
Español
00 Česky
00
Dansk
00 Slovensky
00
Before operating this unit, please read these instructions completely.
ER1510_EU.indb
1
2007/10/31
17:34:06
Important
 Before use
This clipper is designed for professional use to trim hair and
beards. Charge it for 8 hours before use for the fist time in order to
activate the built‑in rechargeable batteries. It can be operated on
either an AC adaptor or rechargeable batteries. Read all
instructions carefully before use.
 Charging the clipper
• Use the ER1510 hair clipper with the RE5‑95 adaptor only.
• Avoid charging the batteries at temperatures below 5 °C or
above 35 °C.
• Avoid charging the batteries in direct sunlight or near a radiating
heat source.
• The charge status (
) lamp may blink at an early stage when
it is used for the first time or if it has not been used for 6 or more
months even if it is fully charged. This is not a malfunction.
• Even though the clipper may not be used for an extended period,
charge every 6 months to preserve battery life.
• The power cord cannot be replaced. If it is damaged, the AC
adaptor should be discarded.
 Using the clipper
• Warning - Keep the appliance dry.
• The clipper may become warm during operation and/or charging.
This is normal.
• Check that the blades and the attachments are not damaged
before use. Replace them if they are damaged.
• You should not allow permanent wave lotion, hair restorer or hair
spray to come into contact with the main body or the blades.
Doing so may result in cracking, discoloring or corrosion.
• You should not drop the clipper on the floor.
• You should not knock the blades and the attachments against
hard objects.
• You should not trim the hair of a pet.
 Cleaning the clipper
• Clean the housing using only a cloth slightly dampened with
water or a mild soap solution.
• Never use a caustic solution.
• Never submerge the clipper in water.
 Storing the clipper
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
• Never tamper with moving parts.
• Avoid grabbing the clipper by the power cord, as it may become
detached, causing damage or injury.
• If the clipper is not working properly, have it inspected at an
authorized service center.
Specifications
Power source: 230 V AC, 50 Hz
Motor voltage: 2.4 V DC
Charging time: 1 hour
Airborne Acoustical Noise: 000 (dB (A) re 1 pW)
READ ALL INSTRUCTIONS BEFORE USE.
ER1510_EU.indb
2
2007/10/31
17:34:06



 

Ch
ar
ge
Parts identification



6mm
0/0"





9mm
0/0"





the power
1 Connect
cord to the charging


3mm
0/0"
12mm
0/0"


4mm
0/0"
AMain body
1Trimming height indicator
2Dial (Height adjustment
control)
30·CHARGE/1 switch
4Battery capacity lamp
5Charge status (
) lamp
6Plug receptance
BBlade
7Mounting hook
8Cleaning lever
9Moving blade
Stationary blade




Charging the hair clipper
15mm
0/0"
C3 mm comb attachment
D4 mm comb attachment
E6 mm comb attachment
F9 mm comb attachment
G12 mm comb attachment
H15 mm comb attachment
IAC adaptor (RE5‑95)
;Power cord
Appliance plug
JCleaning brush
KOil
LCharging stand
Charging plug
Plug receptance
MComb attachment shelves
(×2)
stand.
the 0·CHARGE/1
2 Slide
switch to “0·CHARGE”.
the clipper on
3 Place
the charging stand and
plug in the adaptor
into a household
outlet.
• Charge status (
) lamp glows and charging starts.
• Charging is completed when Charge status (
) lamp
blinks. (Max. 1 hour later)
• 1 full charge will provide approximately 70 minutes of
continuous operation.
ER1510_EU.indb
3
2007/10/31
17:34:07
2.Plug in the adaptor into a household
outlet.
About the LED display
While charging
After charging is
completed
10 minutes after
charging is
completed
HIGH
MID
LOW
HIGH
MID
LOW
HIGH
MID
LOW
blinks once
every second.
blinks once
every 2 seconds.
• “HIGH/MID/LOW”
go out.
While using
HIGH
MID
LOW
“HIGH” blinks - The battery capacity is enough.
“MID” blinks - The battery capacity is approx.
60% or less.
“LOW” blinks - The battery capacity is approx.
10% or less.
Cu
t
glows.
• “HIGH”, “MID” or
“LOW” blinks.
 AC operation
If you connect the AC adaptor to the clipper in the same way as for
charging, and turn on the power, you can use it even if the battery
capacity is low.
• If the clipper does not operate, charge the clipper for
approximately 1 minute.
• Be careful not to discharge the battery completely with the power
left turned on. It results in shortening the battery life.
Using the hair clipper
Turn the dial clockwise or counterclockwise to adjust
the moving blade back and forth to get the desired
height. Adjustable in 5 stages from 0.8 mm to 2.0 mm
in 0.3 mm steps without attachments.
• Charge the clipper when “LOW” starts to blink.
 Charging without the charging stand
1.Slide the 0·CHARGE/1 switch to “0·CHARGE”,
and insert the appliance plug into the clipper.
 Using the comb attachments
the trimming heights
1 Select
indicated on the insides and sides
of the attachments.
the dial to “0.8” and then
2 Set
mount the attachment to the
0.8
clipper as illustrated.
ER1510_EU.indb
4
2007/10/31
17:34:07
Removing the attachment from the clipper
Remove the attachment as illustrated.
 Mounting the blade
1.Set the dial to “2.0”.
re
2.0
Ca
Blade maintenance
 Blade life
Blade life will vary according to the frequency and length of use. It
is expected to be about 3 months when used for 15 haircuts a day.
2.Fit the mounting hook
into the blade mounting
on the clipper and push
in until it clicks.
Cleaning the blade
Removing and mounting the blade
 Removing the blade
1.Hold the clipper with the switch
facing upward and push the
blade with your thumb while
catching the blade in your other
hand.
• Be sure to turn off the power
before you remove the blade.
1.Brush off
2.Remove the
any hairs
blade and
from the
brush off
clipper and
the hairs
from around
from the
the blade.
blade edge.
3.Brush the hairs out from
between the stationary
blade and the moving
blade while pressing
down on the cleaning
lever to raise the moving
blade.
ER1510_EU.indb
5
2007/10/31
17:34:08
Lubrication
1.Apply a few drops of the oil to the space between the
stationary blade and moving blade.
• Apply the oil to the clipper before and after each use.
2.Set the dial to “2.0” and then remount the blade on the
clipper.
Removing the built‑in rechargeable batteries
1.Remove the blades 1 and four screws 2.
2.Remove the spring 3, the under cover 4, and the blade holder
5.
3.Remove the dial 6 and open the housing 7, and then take out
two batteries 8.
• Disconnect the clipper from a household outlet.
• Fully discharge the batteries.
• Be careful not to short-circuit the batteries.






ER1510_EU.indb
6
2007/10/31
17:34:08
Information on Disposal for Users of Waste Electrical &
Electronic Equipment (private households)


WARNING - Do not attempt to replace the batteries for the
purpose of reusing the clipper. This could result in the risk of fire
or electric shock.
Important notice regarding environmental protection
The built‑in rechargeable Nickel‑Metal Hydride batteries contain
substances that may be environmentally harmful. Please remove
the batteries before discarding your clipper.
For environmental protection and recycling materials
This clipper contains Nickel‑Metal Hydride batteries.
Please make sure that the batteries are disposed of at an
officially assigned location, if there is one in your country.
This symbol on the products and/or
accompanying documents means that used
electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling,
please take these products to designated
collection points, where they will be accepted on a
free of charge basis.
Alternatively, in some countries you may be able to return your
products to your local retailer upon the purchase of an
equivalent new product.
Disposing of this product correctly will help to save valuable
resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from
inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste,
in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please
contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the
European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local
authorities or dealer and ask for the correct method of disposal.
ER1510_EU.indb
7
2007/10/31
17:34:08
Matsushita Electric Works, Ltd.
1048, Kadoma, Osaka 571-8686, Japan
No.1 EN, GE, FR, IT, DU, SP, DA, PT, NW, SW, FI, PL, CZ, SK, HU, RO, RU, TK, UA (欧州)
ER1510_EU.indb
8
Printed in Japan
2007/10/31
17:34:09
Download PDF

advertising