Aeg-Electrolux DD9863-M User Manual

Aeg-Electrolux DD9863-M User Manual
DD 9893 - DD 9863
User manual
Cooker Hood
Contents
Safety warnings ................................................................................ 3
Description of the Appliance ........................................................... 5
Extraction mode .................................................................................. 5
Recirculation mode ............................................................................. 5
Control Panel .................................................................................... 6
Grease and charcoal filter maintenance indicator ................................ 8
Maintenance and Care..................................................................... 9
Air suction panels ............................................................................... 9
Inner crosspiece ................................................................................ 10
Metal grease filter ............................................................................. 11
Charcoal filter .................................................................................... 12
Warning ............................................................................................ 13
Changing the light bulbs .................................................................... 13
Cleaning the hood ............................................................................. 13
Special accessories ........................................................................ 13
Something Not Working ................................................................. 14
Technical assistance service ......................................................... 15
Installation ...................................................................................... 17
Technical Details ............................................................................... 17
Mounting accessories included ......................................................... 17
Electrical connection ......................................................................... 18
Before beginning installation .............................................................. 18
Installation ........................................................................................ 20
2
Safety warnings
• When used as an extractor unit, the hood must be fitted with a hose
having preferably the same diameter as the outlet hole.
Should there already be a pipe of diameter 125 mm that ducts to
the outside through the walls or roof, it is possible to use the 150/
125 mm reduction flange provided. In this case the hood will be
slightly noisier.
Attention: The hose is not supplied and must be purchased
separately.
• The minimum distance between the supporting surface for the
cooking vessels on the hob and the lowest part of the range hood
must be not less than 50cm from electric cookers and 65cm from
gas or mixed cookers.
If the instructions for installation for the gas hob specify a greater
distance, this must be adhered to.
• Before any cleaning or maintenance operation, disconnect the hood
from the mains by removing the plug or disconnecting the home
mains switch.
• The appliance is not intended for use by children or persons with
impaired physical, sensorial or mental faculties, or if lacking in
experience or know-how, unless they are under supervision or have
been trained in the use of the appliance by a person responsible for
their safety.
• Children should be monitored to ensure that they do not play with
the appliance.
• Never use the hood without effectively mounted grating.!
• The hood must NEVER be used as a support surface unless
specifically indicated.
• The premises must be sufficiently ventilated, when the kitchen hood
is used together with other gas combustion devices or other fuels.
• The suctioned air must not be conveyed into a conduit used for the
disposal of the fumes generated by appliances that combust gases
or other fuels.
• The flaming of foods beneath the hood itself is severely prohibited.
• The use of exposed flames is detrimental to the filters and may
cause a fire risk, and must therefore be avoided in all
circumstances.
• Any frying must be done with care in order to make sure that the oil
does not overheat and burst into flames.
• As regards the technical and safety measures to be adopted for
fume discharging it is important to closely follow the relations
provided by the competent authorities.
3
• The hood must be regularly cleaned on both the inside and outside
(AT LEAST ONCE A MONTH, it is in any event necessary to
proceed in accordance with the maintenance instructions provided
in this manual)..
• Failure to follow the instructions as concerns hood and filter
cleaning will lead to the risk of fires.
• Do not use or leave the hood without the lamp correctly mounted
because of the possible risk of electric shocks.
• We decline any responsibility for any problems, damage or fires
caused to the appliance as the result of the non-observance of the
instructions included in this manual.
This appliance is marked according to the European directive 2002/96/
EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product.
on the product, or on the documents accompanying
The symbol
the product, indicates that this appliance may not be treated as
household waste. Instead it should be taken to the appropriate
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal.
For more detailed information about treatment, recovery and recycling
of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
4
Description of the Appliance
• The cooker hood is designed to extract unpleasant odours
from the kitchen, it will not extract steam.
• The hood is supplied with the charcoal filter, and can be used
immediately in the recirculation mode. We advise removing the
charcoal filter to use the hood in the extraction mode.
Extraction mode
• In this mode fumes are extracted to the outside via a hose
connected to the coupling ring. Fig. 1
• In order to obtain the best performance the hose should have a
diameter equal to the outlet hole.
Should there already be a pipe of diameter 125 mm that ducts to
the outside through the walls or roof, it is possible to use the 150/
125 mm reduction flange provided. In this case the hood will be
slightly noisier.
Top
Rear
Rear
Top
Coupling ring
Fig. 1
Recirculation mode
• The air is filtered through a charcoal filter and
returned to the kitchen. Fig. 2
• You will need an original charcoal filter for the
recirculation mode. (See Special Accessories).
Fig. 2
5
Control Panel
• Best results are obtained by using a low speed for normal
conditions and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking.
The hood should be left on after cooking for about 15 minutes or
until all the odours have disappeared.
• The hood can also be commanded from the control panel or the
remote control. (the remote control is a special accessory and is
ordered separately).
• Correct ventilation: If the cooker hood is to work correctly there
must be an under pressure in the kitchen. It is important to keep the
kitchen windows closed and have a window in an adjacent room
open.
• The control switches are located on the hood’s front panel
• The cooker hood is fitted with a sensor which, in the event of
extreme variations in temperature, switches the appliance on
automatically until the temperature of the environment surrounding
the hood has been significantly reduced.
6
b
1
2
3
7
a
4
5
6
1. Light switch, ON/OFF
2. Mains switch, ON/OFF
Press for less than 1 1/2 seconds and the cooker hood goes into the
"stand by" position (dot “a” on display is illuminated).
Press for more than 1 1/2 seconds and the cooker hood turns OFF,
ALL the controls (except the light push button) are disabled (the
display is off).
Press again for more than 1 1/2 seconds to reset the cooker hood to
"stand by".
3. Filters saturation reset key: see the relative text on the following
pages.
4. Start and choice of motor speed 1-2-3-1-2...
5. Intensive speed ON/OFF: The Intensive speed runs for 5 minutes:
If the hood is on when the Intensive speed is activated, the hood will
revert to previous speed after 5 minutes. If the hood is off when the
Intensive speed is activated, the hood will automatically turn off after 5
minutes.
The letter P appears on the display and the remaining time (the dot
“b” on display is flashing), if interrupted an acoustic signal is heard.
6. Self-Timer ON/OFF: times all the speed levels (the dot “a” on display
is flashing), and then the cooker hood switches off:
The self-timer is set as follows:
1st speed level 20 minutes
2nd speed level 15 minutes
3rd speed level 10 minutes
The display shows the remaining operation time, at the end of the time
an acoustic signal is heard. Depressing the push-button again exits
the function.
7. Display
Should the hood or the controls fail to operate: disconnect the power
supply for at least 5 seconds. After reconnecting the power supply wait
15 seconds and then check that the cooker hood is now operating
correctly.
7
Grease and charcoal filter maintenance
indicator
This hood is fitted with a device that indicates when it is necessary to
clean the grease filter or the charcoal filter (if the hood is used in the
recirculation version with a charcoal filter).
On delivery, the hood is not supplied with a charcoal filter, so the
saturation indicator will be disabled.
If the hood is to be used with a charcoal filter, the saturation
indicator light must be enabled as follows:
Set in "OFF" the hood.
Press buttons 3 and 4 simultaneously and hold them for 3 seconds. At
first only the grease filter LED F will light up, but when the charcoal
filter LED C lights up the saturation indicator will be enabled.
To disable it: Press buttons 3 and 4 again simultaneously and hold
them for 3 seconds, until the charcoal filter LED goes out.
Grease filter LED (F)
LED F will start to flash when it is time to clean the grease filter.
Cleaning will be necessary after 40 working hours. Always comply
with the maintenance instructions for the grease filter.
Charcoal filter LED (C)
The charcoal filter LED C will start to flash when the charcoal filter
needs to be replaced.
This operation is necessary after approximately 160 working hours.
Resetting the saturation indicator
After cleaning or replacing the filters, press button 3 for 3 seconds until
the grease filter LED F or the charcoal filter LED C stops flashing.
8
Maintenance and Care
Warning! Before performing any maintenance operation, isolate the
hood from the electrical supply by switching off at the connector and
removing the connector fuse.
Or if the appliance has been connected through a plug and socket,
then the plug must be removed from the socket.
Air suction panels
Remove the perimeter air suction panels to access the grease filters.
• DD 9893
The perimeter air suction panels are attached to the cooker hood by
a series of pins and coupling springs; pull them outwards and
detach them from the fastening cable. Fig. 3
When refitting the perimeter air suction panels, ALWAYS reattach
the fastening cables.
Make sure the panels are attached to the cooker hood properly
(snap-fastened).
x2
Fig. 3
9
• DD 9863
Pull the panel (FRONT SIDE) downward with decision, unscrew
safety knob and unhook it from the rear hinge. Fig. 3a
Proceed in the reverse order when refitting it.
Fig. 3a
Clean the perimeter air suction panels as often as the grease filters
(for more information about gentle cleaning methods, read the
paragraph “Cleaning” in the pages that follow).
Inner crosspiece - DD 9893
The inner crosspiece should be removed in order to access the
grease filters and the inside of the cooker hood (for example: when
performing maintenance work on the carbon filters).
To remove it (depending on the model), proceed as follows,Fig. 4:
Warning! Keep the crosspiece supported during removal/fitting
procedures, in order to prevent it from falling and damaging other
objects.
Remove it from its position using the spring release system.
Re-fit the crosspieces by carrying out the above steps in reverse.
Warning! Make sure the crosspiece is fixed to the cooker hood
properly.
Fig. 4
10
Metal grease filter
• The purpose of the grease filters is to absorb grease particles which
form during cooking and it must always be used, either in the
external extraction or internal re-circulation function.
Attention: the metal grease filters must be removed and washed,
either by hand or in the dishwasher, every four weeks.
Removing the metal grease filters
• Push it towards the back of the unit and then pull it down and out.
Fig. 5
Hand washing
Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Repeat
the process if necessary. Refit the grease filters when they are dry.
Dishwasher
Place grease filters in the dishwasher. Select most powerful
washing programme and highest temperature, at least 65°C.
Repeat the process. Refit the grease filters when they are dry.
When washing the metal grease filter in the dishwasher a slight
discolouration of the filter can occur, this does not have any impact
on its performance.
• Clean the inner housing using a hand hot solution only(never use
caustic detergents, abrasive powders or brushes).
Fig. 5
11
Charcoal filter
• The charcoal filter should only be used if you want to use the hood
in recirculation mode.
• Cleaning/replacing the carbon filter
Unlike other carbon filters, the LONGLIFE carbon filter can be
cleaned and reactivated. At normal use the filter should be cleaned
every second month (when using the hood 2,5 hours per day, in
avarage). The best way to clean the filter is in the dishwasher. Use
normal detergent and choose the highest temperature (65º C).
Wash the filter separately so that no food parts gets stuck on the
filter and later causes bad odours. To reactivate the carbon, the filter
should be dried in an oven for 10 minutes with a temperature of
maximum 100º C.
After approximately three years of use, the carbon filter should be
replaced with a new one, as the odour reduction capacity will be
reduced.
• Fitting
Remove the perimeter air suction panels.
Remove the inner crosspiece.
Remove the grease filters.
Position the carbon filter inside the hood to cover the protection grill
of the motor. Fix the filter with 2 lateral knobs. Fig. 5
Reattach the grease filters, the inner crosspiece and the perimeter
air suction panels.
• To remove proceed in the reverse order.
• Always specify the hood model code number and serial number
when ordering replacement filters. This information is shown on the
rating plate located on the inside of the unit.
• The charcoal filter can be ordered from your local Service Force
Centre.
Fig. 5
12
Warning
• Failure to observe the instructions on cleaning the unit and changing
the filters will cause a fire hazard. You are therefore strongly
recommended to follow these instructions.
• The manufacturer declines all responsibility for any damage to the
motor or any fire damage linked to inappropriate maintenance or
failure to observe the above safety recommendations.
Changing the light bulbs
• Disconnect the cooker hood from the
mains supply.
• Prior to touching the light bulbs
ensure they are cooled down.
• Extract the lamp cover by using a small
flat screwdriver or similar tool as a lever.
• Replace the old bulb with a new one of
the same type. Fig. 7
• Refit the lamp cover.
• If the light does not come on, make sure
the bulb has been inserted in correctly
before contacting your local Service
Force Centre.
Fig. 7
Cleaning the hood
• Clean the outside of the hood using a damp cloth and a solution of
water and mild washing up liquid.
• Never use corrosive, abrasive or flammable cleaning products or
products containing bleach.
• Never insert pointed objects in the motor’s protective grid.
• Only ever clean the switch panel and filter grill using a damp cloth
and mild washing up liquid.
• Clean all the plastic parts with a soft cloth soaked in warm water
and neutral soap.
• It is extremely important to clean the unit and change the filters at
the recommended intervals. Failure to do so will cause grease
deposits to build up that could constitute a fire hazard.
Special accessories
Charcoal filter Type 967
Remote control RM 6940
13
Something Not Working
If your appliance fails to work properly please carry out the following
checks.
Symptom
Solution
The cooker hood
will not start...
Check that: The hood is connected to
the electricity supply.
Check that a fan speed has been
selected
The cooker hood
is not working
Check that: The fan speed is set
high enough for the task.
The grease filters are clean.
The kitchen is adequately vented to
allow the entry of fresh air.
If set up for recirculation, check that
the charcoal filter is still effective.
If set up for extraction, check that the
ducting and outlets are not blocked.
The cooker hood has
switched off
during operation...
The safety cut-out device has been
tripped.
Turn off the hob and then wait for
the device to reset.
If the hood has been installed below
the heights indicated in the
installation instructions the motor
will cut-out frequently which will
damage the hood.
If after all these checks, the problem persists, contact your local
Service Centre, quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for
any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have
been made as the engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
14
Technical assistance service (not for UK)
You are welcome to telephone our technical assistance service (see list of technical
assistance centres) whenever you need information or in the unlikely event of a fault.
For service in Australia call 1300 650 020.
When calling, please be ready to specify:
1. The model code number
2. The serial number
3. The product number.
This information is shown on the registration plate inside the unit behind the
grease filter.
We reserve the right to change specifications and colours as a result of our policy of
continuing technological development.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare
parts, contact your local Service Force Centre by telephoning: 08705 929 929
Your call will be automatically routed to the Service Centre covering your post code
area. For the address of your local Service Force Centre and further information
about Service Force, please visit the website at www.serviceforce.co.uk
Please ensure that you have read the section “What to do if...” as the engineer will
make a charge if the fault is not a mechanical or electrical breakdown even the
appliance is under warranty. Please note that proof of purchase is required for inguarantee service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
• Your name
• Clear and concise details of the fault
• Address and post code • Name and model of the appliance*
• Telephone number
• Product number*
• Serial number*
* This information can be found on the rating plate, which can be seen when the
grease filters are removed.
If you require Customer Service in the Republic of Ireland please contact us at
the address below:
AEG
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0) 1 4090751
Email: [email protected]
15
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your AEG appliance or for further information on AEG
products, please contact our Customer Care Department by letter or telephone at the
address below or visit our website at www.aeg.co.uk
Customer Services Department
Major Appliances
AEGElectrolux
Addington Way
Luton
Bedfordshire
LU4 9QQ
08705 350 350 (*)
* calls to this number may be recorded for training purposes
16
Installation
Technical Details
Dimensions (in cm):
Height (Extract. mode):
Height (Recirc. mode):
Width:
Depth:
Max. absorb. power:
Motor:
Lighting:
Length of the cable:
Electrical connection:
Fuse rating:
DD 9863
DD 9893
85,5-129,5
96-140
59,8
39
290 W
250 W
2 x 20 W
150 cm
220-240 V
5At
85,5-129,5
96-140
89,8
39
290 W
250 W
2 x 20 W
150 cm
220 - 240 V
5At
Mounting accessories included
1
1
2
1
1
6
6
2
8
4
2
2
2
reduction flange
deflector (with extensions)
screwdriver bits (for TORX screws)
fixing bracket for motor unit
support bracket for flues (3 pieces to assemble)
screws 5 x 45 mm
dowels Ø 8 mm
screws 2.9 x 6.5
screws 3.5 x 6.5
screws 4 x 8
large plug caps
small plug caps
washers
17
Electrical connection
Safety warnings for the electrician
The mains power supply must correspond to the rating indicated on
the plate situated inside the hood. If provided with a plug connect the
hood to a socket in compliance with current regulations and positioned
in an accessible area. If it not fitted with a plug (direct mains
connection) or if the plug is not located in an accessible area apply a
bi-polar switch in accordance with standards which assures the
complete disconnection of the mains under conditions relating to overcurrent category III, in accordance with installation instructions.
IMPORTANT: Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that the
mains cable is correctly assembled.
Before beginning installation
• In addition check whether near the installation area of the hood (in
the area accessible also with the hood mounted) an electric
connection to the mains is available and if it is possible to connect a
fumes discharge device to the outside (Extraction mode only).
• Warning! Do not connect the appliance to the mains until the
installation is fully complete.
18
First decide which functioning
version is better for you
B
180°
If you decide to use the hood in exhausting
version we suggest you position the upper
section of the chimney so that the oulet
slots are not visible once installation has
ended, on the contrary if it is decided to
use the hood in recycling version BE SURE
that the side with the slots is upright (see
also A-B-C sequence).
Assembling the chimney flue
support/bracket (3 parts)
A
C - OK!
4 x Ø 4x8
G
=
The three parts should be fixed with 4
screws, the support extension is
adjustable and should correspond to the
internal width of the telescopic chimney
flue.
X
=
X
=
Assembling the deflector
(3 parts – only for filter
version):
The three parts should be fixed with 2
screws, the deflector extension is
adjustable and should correspond to the
width of the chimney flue support, to
which it is then fixed.
X
=
F
6x
Ø 3,5 x 6,5
F
G
19
Installation - Fig. 8-9
Remove the perimeter air suction panels, the inner crosspiece and the
grease filters.
• Mark a central line on the wall to facilitate the installation procedure
(1). Position the drilling template so that the median line printed on it
corresponds to the central line marked previously, and so that the
lower side of the template corresponds to the lower part of the
cooker hood once it has been fitted (2).
• Make 4 holes with Ø 8 mm (2 on top and 2 underneath) and fit 4
rawl plugs into them (3).
• Fix the motor assembly support bracket in place using 2 screws (4).
• Make two holes with Ø 8 mm near the ceiling and use them to fix
the support bracket of flue G in place (use the bracket as a
template – rest it against the wall which joins onto the ceiling). Insert
2 rawl plugs into the holes (5) (install deflector F underneath the
bracket using 4 screws if you wish to use the cooker hood as a filter
version) and fix the bracket in place using 2 screws (6).
• Fit the cooker hood (7) and adjust its position (8-9).
• Fix the cooker hood in place (10).
Note: Use 2 screws with washers and close off the holes using 2
large plug caps.
• Install the exhaust tube (11) leading from cooker hood exhaust
outlet B to the outside environment (ducted version) or deflector F
(filter version).
• Perform all necessary electrical connections (12).
20
4 x Ø 3,5x6,5
G
F
5
G
2 x Ø 5x45
2xØ8
6
12
1
$93 cm
11
2
7
2xØ8
3
4
B
2x
Ø 5x45
3
8
9
3
2xØ8
10
2 x Ø 5x45
H ($65cm)
H ($50cm)
Fig. 8
21
• Fix the lower duct in place using two screws, working from inside the
cooker hood, then close off the holes using the small plug caps (13).
• Pull out the upper flue and, at the top, fix it to bracket G using 2
screws (14).
Fit the grease filters, the inner crosspiece and the perimeter air suction
panels.
Connect the hood to the mains electricity (wait about 15 seconds, the
time needed to calibrate the electronic device that controls the
functioning of the hood), and check, finally, that it is functioning well.
G
2 x Ø 2,9x6,5
14
14
13
13
Fig. 9
22
2 x Ø 3,5x6,5
13
23
LI3Q4B
Ed. 04/09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement