Zanussi | ZWN6120L | User manual | ZANUSSI ZWN6120L User Manual

EN
User manual
Washing Machine
ZWN 6120 L
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 11
Washing programmes _ _ _ _ _ _ _ _ _ _ _ _
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _
12
15
17
20
20
21
24
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep
the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• Do not let persons, children included, with reduced physical sensory, reduced mental functions or lack of experience and knowledge use the appliance. They must have supervision or instruction
for the operation of the appliance by a person who is responsible
for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• If the appliance has a child safety device, we recommend you activate it.
General Safety
• Before maintenance, deactivate the appliance and disconnect the
mains plug from the mains socket.
• Do not change the specification of this appliance.
2
www.zanussi.com
• Obey the maximum load volume of 8 kg (refer to the “Programme
chart” chapter).
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
• The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Obey the installation instruction supplied with
the appliance.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the appliance door can not be fully opened.
• Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
• Make sure that there is air circulation between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
Electrical connection
Warning! Risk of fire and electrical shock.
• The appliance must be earthed.
www.zanussi.com
• Make sure that the electrical information on
the rating plate agrees with the power supply.
If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains
plug with wet hands.
• Only for UK and Ireland. The appliance has a
13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
•
This appliance complies with the E.E.C. Directives.
3
Water connection
• Make sure not to cause damage to the water
hoses.
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Use
Warning! Risk of injury, electrical shock,
fire, burns or damage to the appliance.
• Use this appliance in a household environment.
• Obey the safety instructions on the detergent
packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
• Make sure that you remove all metal objects
from the laundry.
4
• Do not put a container to collect possible water leakage under the appliance. Contact the
Service to ensure which accessories can be
used.
Care and Cleaning
Warning! Risk of injury or damage to the
appliance.
• Do not use water spray and steam to clean
the appliance.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Service
• Contact the Service to repair the appliance.
We recommend only the use of original spare
parts.
www.zanussi.com
Product description
1 Detergent dispenser drawer
2 Control panel
1
2
3 Door opening handle
4 Rating plate
5 Drain pump
6 Adjustable feet
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for prewash
and soak phase or for stain remover used during
the stain action phase (if available). The prewash
and soak detergent is added at the beginning of
the wash programme. The stain remover is added during the stain action phase.
Compartment for powder or liquid detergent
used for main wash. If using liquid detergent
pour it just before starting the programme.
Compartment for liquid additives (fabric softener, starch).
MAX
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the
«MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must
be poured into the compartment before starting the wash programme.
Flap for powder or liquid detergent (see "Flap for powder or liquid detergent" in the
chapter "Daily use" for more details).
www.zanussi.com
5
Child safety
Make sure that children or pets do not climb into the drum. To prevent children and pets becoming trapped inside the drum this machine incorporates a special feature.
To activate this device, rotate the button
(without pressing it)
inside the door clockwise until the groove
is horizontal. If necessary use a coin.
To disable this device and restore the
possibility of closing
the door, rotate the
button anti-clockwise
until the groove is vertical.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as the
buttons and pilot lights. These are presented by relevant numbers on the following pages.
1
2
3
4
5
1 Programme selector dial
2 SPIN reduction button
5 START/PAUSE button
6 DELAY START button
3 OPTIONS button
4 EXTRA RINSE button
7 Indicator pilot lights
7
6
Programme selector dial, spin speed button and available options
Programme Selector Dial
It allows you to switch the appliance on/off and/
or to select a programme.
6
Available options:
Spin
By pressing this button you can change the spin
speed of the set programme or select the available option(s).
www.zanussi.com
Rinse hold
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will be
necessary to empty out the water. To empty out
the water, please read the paragraph «At the
end of the programme».
Prewash
By selecting this option the machine performs a
prewash cycle before the main wash phase. The
washing time will be prolonged. This option is
recommended for heavily soiled laundry.
Super Quick
Short cycle for lightly soiled items or for laundry
which needs only freshening up. We recommend you to reduce the fabrics loading.
Extra Rinse
This appliance is designed to save energy. If it
necessary to rinse the laundry using an extra
quantity of water (extra rinse), select this option.
Some additional rinses will be performed. This
option is recommended for people who are allergic to detergents, and in areas where the water is very soft.
Delay Start
The start of the programme can be delayed by
3, 6 or 9 hours by means of this button.
Indicator pilot light
A
B
C
When selecting a washing programme both
lights A and B illuminate.
After having pressed the button 5 the only
light corresponding to the running phase
stays on. The machine starts working and the
door is locked.
The light C illuminates at the end of the washing cycle. After a few minutes the door can be
opened.
If the draining programme is selected any
light will illuminate.
Start Pause
This button allows you to start or to interrupt the
selected programme.
First use
• Ensure that the electrical and water connections comply with the installation instructions.
• Remove the polystyrene block and any
material from the drum.
• Pour 2 litres of water into the main wash
of the detergent drawer
compartment
www.zanussi.com
in order to activate the ECO valve. Then
run a cotton cycle at the highest temperature without any laundry in the machine,
to remove any manufacturing residue
from the drum and tub. Pour 1/2 a
measure of detergent into the main wash
compartment and start the machine.
7
Daily use
Load the laundry
Flap for powder or liquid detergent
Open the door by
carefully pulling the
door handle outwards. Place the
laundry in the drum,
one item at a time,
shaking them out as
much as possible.
Close the door.
Make sure that no
laundry stays between the seal and
the door. There is a
risk of water leakage
or damage to the
laundry.
UP- The flap position if using POWDER detergent
DOWN - The flap
position if using
LIQUID detergent
during main wash
If the flap is not in the desired position:
• Pull out the dispenser drawer until
it stops.
Measure out the detergent and the fabric
softener
MA
X
M
AX
MAX
The flap is down and you wish to use
powder detergent:
• Turn the flap up.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required, pour it into the main wash compartor in the appropriate compartment if
ment
the selected programme/option it requires
(see more details in "Detergent dispenser
drawer").
If required, pour fabric softener into the com(the amount used must
partment marked
not exceed the «MAX» mark in the drawer).
Close the drawer gently.
8
www.zanussi.com
MAX
• Measure out the
detergent.
• Pour the powder
detergent into the
main wash com.
partment
• Remove the remaining powder form
the flap.
• There is remaining powder detergent
in the main wash compartment at the
end of a washing programme. Check if
the flap is in the right position.
The flap is up and you wish to use liquid
detergent:
• Turn the flap down.
• Do not use liquid detergent if the washing
programme doesn't start immediately.
In these cases, use the flap in "UP" position .
Select the required programme by turning
the programme selector dial (1)
Turn the programme selector dial to the required programme. The washing machine will
automatically select the maximum spin value
provided for the programme you have chosen.
You can change this value by pressing the corresponding button. The green pilot light of the
button 5 starts to flash.
The selector dial can be turned either clockwise
to reor counterclockwise. Turn to position
set programme/Switching the machine off.
At the end of the programme the selector
, to
dial must be turned to position
switch the machine off.
Caution! If you turn the programme
selector dial to another programme when
the machine is working, the red pilot light of
button 5 will blink 3 times to indicate a wrong
selection. The machine will not perform the new
selected programme.
• Measure out the
detergent.
MAX
For the quantity
of detergent, refer always to what is
written on the product
packing and ensure
that the detergent can
be poured in the
drawer.
• Pour the liquid detergent in the compartwithout exceeding the limit indicament
ted in the flap.
• Close the dispenser drawer.
Warning! Do not use the flap in "DOWN"
position with:
• Gelatinous detergent or thick detergent.
• Powder detergent.
• With programmes with prewash.
www.zanussi.com
Select the spin speed or Rinse Hold by
pressing button 2
When selecting a programme, the appliance
proposes automatically the maximum spin
speed provided for that programme. (See
"Washing programmes" for the maximum allowed spin speed).
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
different speed. The relevant pilot light illuminates.
Select the available options by pressing
buttons 3 and 4
Depending on the programme, different functions can be combined. These must be selected
after choosing the desired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot lights illuminate. When they are
pressed again, the pilot lights go out. If an incorrect option is selected, the integrated red pilot
light of the button 5 flashes for 3 times.
9
For the compatibility among the washing
programmes and the options see chapter
«Washing Programmes».
Select the Delay Start by pressing button
6
Before you start the programme, if you wish to
delay the start, press the button 6 repeatedly, to
select the desired delay. The relevant light illuminates.
You must select this option after you have set
the programme and before you start the programme.
You can cancel or modify the delay time at any
moment, before you press button 5.
Selecting the delayed start:
1. Select the programme and the required options.
2. Select the delay start by pressing the button 6.
3. Press button 5:
– the machine starts its hourly countdown.
– The programme will start after the selected delay has expired.
Cancelling the delayed start after having started
the programme:
1. Set the washing machine to PAUSE by
pressing button 5.
2. Press button 6 once, the light relevant to
the selected delay goes off
3. Press button 5 again to start the programme.
The Delay Start can not be selected with
DRAIN programme.
Important! The selected delay can be changed
only after selecting the washing programme
again.
The door will be locked throughout the delay
time. If you need to open the door, you must set
the machine to PAUSE (by pressing the button
5) and then wait a few minutes. After you have
closed the door, press the button 5 again.
Start the programme by pressing button 5
To start the selected programme, press the button 5, the corresponding green pilot light stops
blinking. The pilot light corresponding to the
10
running phase illuminates. The appliance starts
operating and the door is locked.
To interrupt a programme which is running,
press the button 5: the corresponding green pilot light starts blinking.
To restart the programme from the point at
which it was interrupted, press the button 5
again. If you have chosen a delayed start, the
machine will begin the countdown.
If an incorrect option is selected, the red pilot
light of the button 5 blinks 3 times.
Interrupting a programme
Press the button 5 to interrupt a programme
which is running, the corresponding green pilot
light starts blinking.
Press the button again to restart the programme.
Cancelling a programme
to cancel a proTurn the selector dial to
gramme which is running. Now you can select a
new programme.
Opening the door
After the programme has started the door is
locked. If, for any reason, you need to open it,
set firstly the machine to PAUSE by pressing
the button 5. After a few minutes it will be possible to open the door.
If the door remains locked, this means that the
machine is already heating or that the water level is too high. In any case, do not try to force the
door!
If you cannot open the door but you need to
open it you have to switch the machine off by
. After a few miturning the selector dial to
nutes the door can be opened (pay attention
to the water level and temperature!).
After closing the door, it is necessary to select
the programme and options again and to press
button 5.
At the end of the programme
The machine stops automatically. The light of
button 5 and the light corresponding to the just
finished washing phase go off.
The light C illuminates. After a few minutes the
door can be opened.
If you have set a programme or an option that
ends with water left in the tub, the light C illumiwww.zanussi.com
nates. The door remains locked to indicate that
the water must be emptied out before opening
the door. During this time, the drum continues
to run at regular intervals until the water draining.
Follow the below instructions to empty out the
water:
1. Turn the programme selector dial to
.
2.
3.
Set the draining or spinning programme.
If needed, reduce the spin speed, .
Stand by: once the programme has finished after a few minutes the energy saving
system is enabled with the pilot lights switched
4. Press button 5.
At the end of the programme, the door can be
now opened. Turn the programme selector dial
to switch the machine off.
to
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not intend to carry out another wash, close the water
tap. Leave the door open to prevent the formation of mildew and unpleasant smells.
on. By pressing any button the appliance will
come out of the energy saving status.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the wash.
New coloured items may run in the first wash;
they should therefore be washed separately the
first time.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab
the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with
rust stains which are not recent since the cellulose structure will already have been damaged
and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any residual marks with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone1), then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent
paste.
1) do not use acetone on artificial silk
www.zanussi.com
11
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the environment.
Although biodegradable, detergents contain
substances which, in large quantities, can upset
the delicate balance of nature.
The choice of detergent will depend on the type
of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of soiling.
All commonly available washing machine detergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C
max) and woollens
• liquid detergents, preferably for low temperature wash programmes (60°C max) for all
types of fabric, or special for woollens only.
The detergent and any additives must be placed
in the appropriate compartments of the dispenser drawer before starting the wash programme.
If using liquid detergents, a programme without
prewash must be selected.
Your appliance incorporates a recirculation system which allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of hardness. Information on hardness of
the water in your area can be obtained from the
relevant water supply company, or from your local authority. If the water hardness degree is
medium or high we suggest you to add a water
softener following always the manufacturer’s instructions. When the degree of hardness is soft,
readjust the quantity of the detergent.
Washing programmes
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry
Detergent
Compartment
Options
COTTONS
90° - 30°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 8 kg - Reduced load 4 kg
White and coloured cotton (normally soiled items).
SPIN REDUCTION
RINSE HOLD
PREWASH
SUPER QUICK1)
EXTRA RINSE
2)
COTTONS ECO 3)
and
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 8 kg
This programme can be selected for normally soiled cotton items.
This allows to obtain a good washing efficiency by saving energy.
SPIN REDUCTION
RINSE HOLD
PREWASH
EXTRA RINSE1)
2)
12
www.zanussi.com
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry
Options
Detergent
Compartment
SYNTHETICS
60° - 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3,5 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured garments,
shirts, blouses.
SPIN REDUCTION
RINSE HOLD
PREWASH
SUPER QUICK1)
EXTRA RINSE
2)
EASY IRON
40°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 1 kg
Synthetic or mixed fabrics: selecting this programme the laundry is gently washed and spun to avoid any creasing. In this way
ironing is easier. Furthermore the machine will perform additional
rinses.
SPIN REDUCTION
RINSE HOLD
PREWASH
EXTRA RINSE
2)
DELICATES
40°- 30°
Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load 3 kg - Reduced load 1,5 kg
Delicate fabrics: acrylics, viscose, polyester.
SPIN REDUCTION
RINSE HOLD
PREWASH
SUPER QUICK1)
EXTRA RINSE
2)
HANDWASH
40°- 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool as well as for
hand washable woollens and delicate fabrics. Note: A single or
bulky item may cause imbalance. If the appliance doesn’t perform
the final spin phase, add more items, redistribute the load manually and then select the spinning programme.
SPIN REDUCTION
RINSE HOLD
WOOL
40°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool as well as for
hand washable woollens.
SPIN REDUCTION
RINSE HOLD
www.zanussi.com
13
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry
Detergent
Compartment
Options
SPORT INTENSIVE
40°
Prewash - Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
This programme is suitable for washing heavily soiled sport items.
The machine will add automatically a pre wash phase before the
main wash to eliminate mud stains. We recommend you not to
put the detergent into the
compartment of the detergent
drawer.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
MIX 20°
20°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3 kg
Highly energy efficient cold wash programme for lightly soiled
laundry. This programme requires a detergent which is active in
cold water.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
RINSE
Rinses
Maximum spin speed at 1200 rpm
Max. load 8 kg
With this programme it is possible to rinse and spin cotton garments which have been washed by hand. The machine performs
3 rinses, followed by a final long spin. The spin speed can be reduced.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
DRAIN
Draining of water
Max. load 8 kg
For emptying out the water
SPIN
Drain and long spin
Maximum spin speed at 1200 rpm
Max. load 8 kg
Separate spin for hand washed garments and after programmes
with the Rinse Hold option selected. You can choose the spin
speed by pressing the relevant button to adapt it to the fabrics to
be spun.
SPIN REDUCTION
= OFF
For cancelling the programme which is running or to switch the machine off .
1) If you set the SUPER QUICK option we recommend that you reduce the load as indicated in the chart.
2) If using liquid detergents, a programme without PREWASH must be selected.
3) Standard programmes for the Energy Label consumption values.
According to regulation 1061/2010, these programmes are respectively the «Standard 60 °C cotton
programme» and the «Standard 40 °C cotton programme». They are the most efficient programmes in terms of
combined energy and water consumptions for washing normally soiled cotton laundry.
14
www.zanussi.com
The water temperature of the washing phase may differ from the temperature declared for the selected
programme.
Care and cleaning
Warning! You must DISCONNECT the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It is a
good idea to periodically use a water softening
powder in the machine. Do this separately from
any laundry washing, and according to the softening powder manufacturer's instructions. This
will help to prevent the formation of lime deposits.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Having removed the
drawer, use a small
brush to clean the recess, ensuring that all
washing powder residue is removed from
the upper and lower
part of the recess.
Replace the drawer and run the rinse programme without any clothes in the drum.
Cleaning the pump
The pump should be inspected regularly and
particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump;
• a problem with water draining is detected
(see chapter “What to do if...” for more details).
MA
X
M
AX
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Cleaning the drawer recess
Warning! Before opening the pump door,
switch the appliance off and remove the
mains plug from the socket.
Remove the drawer
by pressing the catch
downwards and by
pulling it out. Flush it
out under a tap, to remove any traces of
accumulated powder.
www.zanussi.com
To aid cleaning, the
top part of the additive compartment
should be removed.
Proceed as follows:
• Unplug the appliance.
• If it is necessary, wait until the water has
cooled down.
Open the pump door.
Place a container
close to the pump to
collect any spillage.
15
Pull out the emergency emptying hose,
place it in the container and remove its
cap.
When no more water comes out, unscrew the
pump cover by turning it anti-clockwise and
remove the filter. Use pliers, if necessary. Always keep a rag nearby to dry up any water
spillages when removing the cover.
Clean the filter under a tap, to remove any
traces of fluff.
Remove foreign bodies and fluff from the
filter seat and from
the pump impeller.
Close the pump door.
Caution! When the appliance is in use
and depending on the programme selected
there can be hot water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When refitting
the pump cover, ensure it is securely retightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, takes
long to fill with water, the starting button blinks
yellow or the display (if available) shows the
relevant alarm (see chapter "What to do if..." for
more details), check if the water inlet filters are
blocked .
To clean the water inlet filters:
Check carefully whether the pump impeller rotates (it rotates jerkily). If it doesn’t rotate,
please contact your Service Centre.
Put the cap back on the emergency emptying
hose and place the latter back in its seat.
Replace the filter into
the pump by inserting
it correctly into the
special guides. Screw
the pump cover firmly
by turning it clockwise.
16
• Turn off the water
tap.
• Unscrew the hose
from the tap.
• Clean the filter in
the hose with a stiff
brush.
• Screw the hose back onto the tap. Make
sure the connection is tight.
www.zanussi.com
• Unscrew the hose from the machine. Keep
a rag nearby because some water may flow.
• Clean the filter in the valve with a stiff brush
or with the piece of cloth.
35°
45°
• Screw the hose back to the machine and
make sure the connection is tight.
• Turn on the water tap.
Frost precaution
If the machine is exposed to temperatures below 0°C, certain precautions should be taken.
• Turn off the water tap.
• Unscrew the inlet hose.
• Place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain out.
• Screw the water inlet hose back on and reposition the emergency emptying hose after
having put the cap on again.
• When you intend to start the machine up
again, make sure that the room temperature is
above 0°C.
Emergency emptying out
If the water is not discharged, proceed as follows to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled
down;
• open the pump door;
• place a bowl on the floor and place the end
of the emergency emptying hose into the
bowl. Remove its cap. The water should drain
by gravity into the bowl. When the bowl is full,
put the cap back on the hose. Empty the
bowl. Repeat the procedure until water stops
flowing out;
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its
seat after having plugged it;
• screw the pump cover again and close the
door.
Important! Every time you drain the water
through the emergency emptying hose you must
pour 2 litres of water into the main wash
compartment of the detergent drawer and then
run the drain programme. This will activate the
ECO Valve device avoiding that part of the
detergent remains unused at next washing.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be solved
easily without calling out an engineer. Before
contacting your local Service Centre, please
carry out the checks listed below.
During machine operation it is possible that the
red pilot light of button 5 blinks to indicate that
the machine is not working.
www.zanussi.com
Once the problem has been eliminated, press
the button 5 to restart the programme. If after all
checks, the problem persists, contact your local
Service Centre.
17
Problem
Possible cause/Solution
The washing machine does
not start:
The door has not been closed (the button 5 red light blinks).
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The programme selector dial is not correctly positioned and the button 5
has not been pressed.
• Please turn the selector dial and press the button 5 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The machine does not fill:
The water tap is closed (the button 5 red light blinks).
• Open the water tap.
The inlet hose is squashed or kinked (the button 5 red light blinks).
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked (the button 5
red light blinks).
• Clean the water inlet filters. (See "Cleaning the water inlet filters" for
more details).
The door is not properly closed (the button 5 red light blinks).
• Close the door firmly.
The machine does not empty
and/or does not spin:
The drain hose is squashed or kinked (the button 5 red light blinks).
• Check the drain hose connection.
The drain filter is clogged (the button 5 red light blinks).
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or a
that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much foam) has
been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is
not always easy to see this as the water runs down the hose; check to
see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The cap on the emergency emptying hose has not been replaced or the
filter has not been properly screwed in after cleaning action.
• Refit the cap on the emergency emptying hose or screw the filter fully
in.
18
www.zanussi.com
Problem
Possible cause/Solution
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait a few minutes before opening the door.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the laundry
is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes,
the laundry is still not evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and select the spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the
spinning programme.
The machine makes an unusual noise:
The machine is fitted with a type of motor which makes an unusual noise
compared with other traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the drum when spinning,
as well as increased stability of the machine.
No water is visible in the
drum:
Machines based on modern technology operate very economically using
very little water without affecting performance.
www.zanussi.com
19
Mod
Prod . ...
. No.
...
...
...
...
..
Ser.
No.
...
...
...
If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the
Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Technical data
Dimensions
Width
Height
Depth
Depth (Overall dimensions)
60 cm
85 cm
60 cm
63 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate, on
the inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Cotton
8 kg1)
Spin Speed
Maximum
1200 rpm
1) Maximum load in accordance with EN60456.
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and
type of laundry, the water and ambient temperature.
Programmes
Cottons 60 °C
Cottons 40 °C
Load
(kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
programme duration (minutes)
Remaining
moisture
(%)1)
8
1.4
63
160
53
8
0.6
63
130
53
Synthetics 40 °C
3,5
0.6
54
80
35
Delicates 40 °C
3
0.6
63
65
35
Wool/Hand wash
30 °C
2
0.25
55
60
30
Standard cotton programmes
Standard 60 °C
cotton
8
1.17
61
205
53
Standard 60 °C
cotton
4
0.77
49
159
53
20
www.zanussi.com
Programmes
Standard 40 °C
cotton
Load
(kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
programme duration (minutes)
Remaining
moisture
(%)1)
4
0.7
48
161
53
1) At the end of spin phase.
Off Mode (W)
Left On Mode (W)
0.10
0.98
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
Installation
Rubber feet kit (4055126249)
Available from your authorized dealer.
The rubber feet are particularly recommended
on floating, slippery and wooden floors.
Mount the rubber feet to prevent vibration,
noises and displacement of the appliance during operation.
Read carefully the instructions supplied with the
kit.
Fixing plate kit (4055171146)
Available from your authorized dealer.
If you install the appliance on a plinth, secure
the appliance in the fixing plates.
Follow the instructions supplied with the kit.
After removing all the
packaging, carefully
lay machine on it's
back to remove the
polystyrene base from
the bottom.
Remove the power
supply cable and the
hose from the hose
holders on the rear of
the appliance.
Unscrew the three
bolts.
Slide out the relevant
plastic spacers.
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever has
to be transported again.
www.zanussi.com
21
thick under the appliance, secured to at least 2
floor beams with screws, the wood panel must
extend beyond the front feet.
If possible install the appliance in one of the
corners of the room, where the floor is more stable.
Open the porthole,
remove the polystyrene block fitted on
the door seal and pull
out all items from the
drum.
Fill the smaller upper
hole and the two
large ones with the
corresponding plastic
plug caps supplied in
the bag containing
the instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
raising or lowering the feet. The feet may be
tight to adjust as they incorporate a self locking
nut, but the machine MUST be level and stable.
Any necessary adjustment can be made with a
spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar materials under the machine to compensate for any
unevenness in the floor.
If necessary, check
the setting with a spirit level.
Water inlet
The inlet hose is supplied with the appliance
and it can been found inside the machine drum.
Warning! This appliance must be
connected to a cold water supply.
Caution! Before connecting up the
appliance to new pipework or to pipework
that has not been used for some time, run off a
reasonable amount of water to flush out any
debris that may have collected.
Caution! Do not use the hose from your
previous appliance to connect to water
supply.
1.
35°
Connect the appropriate end of
the hose to a tap
with a 3/4”
thread. Always
use the hose
supplied with the
appliance.
45°
Installation on suspended flooring
Suspended wooden floors are particularly susceptible to vibration.
To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm
22
www.zanussi.com
2.
Connect the other end of the inlet hose to
the back of the appliance. The inlet hose
can ONLY be turned as showed in the
picture.
Do not place the inlet hose downwards. Angle the hose to the left or right
depending on the position of your water
tap. Set the hose correctly by loosening
the ring nut. After positioning the inlet
hose, be sure to tighten the ring nut again
to prevent leaks.
Caution! The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to purchase
a new, longer hose specially designed for this
type of use.
Warning! Installation should comply
with local water authority and
building regulations’ requirements.
The appliance must be connected to a
cold water supply.
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
If you cannot make the cold water connection
direct from the rising mains, you may be able to
operate the appliance from your cold water
storage system.
There should be a minimum vertical distance of
5.02 m (16.5 ft) between the appliance’s inlet
and the bottom of the water storage tank.
“U” piece supplied
Place the drain hose into your standpipe,
which should have an internal diameter of approximately 38 mm thus ensuring there is an
air break between the drain hose and standpipe.
When discharging into a standpipe ensure
that the top of the standpipe is no more than
90 cm (35.4'') and no less than 60 cm (23.6'')
above floor level.
38 mm (1.5”)
standpipe
diamater
30 cm (12”)
The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local
Service Force Centre. The joining piece must
have an internal diameter of 18 mm.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system using one of the following methods.
1. Into a drainage standpipe.
Min. 60 cm (23.6”)
Max. 90 cm (35.4”)
Firstly form a hook in the end of the drain hose
using the “U” piece” supplied.
www.zanussi.com
23
If your drain hose
looks like this (see
beside) you do not require the “U” piece”.
Just push the hose
firmly in to the standpipe.
If you intend to drain the hose from the machine into a sink, make sure that the sink is
empty and the plug hole is not blocked. Use
the plastic “U - Piece” supplied.
2. Onto a sink outlet spigot.
Loop
If the outlet spigot
has not been used
before, remove any
blanking plug that
may be in place.
Push the drain hose
onto the spigot and
secure with a clip, ensure a loop is formed
in the drain hose (see
above) to prevent
waste from the sink
entering the appliance.
In the interest of the environment
The appliance should be connected to the
FOUL drainage system, the water will then be
taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to the surface water drainage system as
this water is discharged directly into a river or
stream and may cause pollution.
If you require any further advice please contact
your local water authority.
SHOWER
SINK TOILET
BATH
BIDET
WASHING
MACHINE
DISHWASHER
RAINWATER
‘RUN-OFF’
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
RIVER
FOUL DRAIN
FOUL SEWERS
SEWAGE TREATMENT
WORKS
TREATED DISCHARGE
RIVER
Environment concerns
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility
or contact your municipal office.
24
Packaging materials
are reThe materials marked with the symbol
cyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of them properly in appropriate collection containers.
www.zanussi.com
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
• Normally soiled laundry may be washed without prewashing in order to save detergent,
water and time (the environment is protected
too!).
www.zanussi.com
• The machine works more economically if it is
fully loaded.
• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can
then be washed at a lower temperature.
• Measure out detergent according to the water hardness, the degree of soiling and the
quantity of laundry being washed.
25
26
www.zanussi.com
www.zanussi.com
27
192985533-A-302013
www.zanussi.com/shop
Download PDF

advertising