AEG | EWA5210 | User manual | Aeg EWA5210 User Manual

WATERKETTLE MODEL EWA 5110/5210
EN
D
B
EN
E
F
C
A
G
H
I
EN
Components
A.
B.
C.
D.
E.
F.
G.
H.
I.
Jug
Spout
Lid
Opening lid button
Handle
Water level indicator
ON/OFF switch with
indicator light
Separate base and mains
cable
2
Safety advice
EN
Read the following instruction
carefully before using the appliance for
•
•
level surface.
•
•
•
•
•
•
•
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to
ensure that they do not play with the
appliance.
The appliance may only be connected
to a power supply whose voltage
and frequency comply with the
Never use or pick up the appliance if
– the supply cord is damaged,
– the housing is damaged.”
The appliance must only be
connected to an earthed socket. If
necessary an extension cable suitable
for 10 A can be used.
If the appliance or the supply cord
is damaged, it must be replaced by
the manufacturer, its service agent or
avoid hazard.
3
•
•
•
and the mains plug withdrawn before
cleaning and maintenance.
The appliance and accessories
become hot during operation. Use
only designated handles and knobs.
Allow to cool down before cleaning or
storage.
The mains cable must not come into
contact with any hot parts of the
appliance.
Do not immerse the appliance in
water or any other liquid.
‘
there is a risk that the boiling water
may spray out, which could scald or
•
•
•
•
•
above the maximum marking.
Never operate appliance with open
lid.
Do not use or place the appliance on
a hot surface or near source of heat.
Only use the kettle for heating water!
The kettle can only be used with the
stand provided.
Appliance is for indoor use only.
This appliance is intended for
domestic use only. The manufacturer
cannot accept any liability for possible
damage caused by improper or
incorrect use.
GB
Getting started
EN
EN
1.
, rinse the inside and
wipe the outside of the kettle with a
damp cloth.
4. Close the lid and make sure it snaps
in correctly. Otherwise the auto
reliably. Place the kettle onto the
base. Press down the ON/OFF switch;
the indicator light will illuminate and
the kettle will start to heat up.
2. Place the base unit
surface. Plug the mains plug into a
wall socket. Excess cord can be wound
into the bottom of base unit.
3. Press the button to open the lid,
pour water into the kettle. It is also
spout, without opening the lid. Make
sure water level is visible in the water
level indicator, but not exceeding the
Max. mark.
When the water has boiled or the
kettle is moved from the base, it will
stop the heating process before the
water is boiling, simply lift up the ON/
OFF switch to the OFF position.
4
Cleaning
GB
EN
1. Before cleaning, always unplug the
appliance. Never rinse or immerse
the kettle or base unit in water. Just
wipe with a damp cloth, using no
abrasive detergents. Occasionally
rinse out the kettle with clean water.
, grab the
strainer insert and lift out.
Cleaning the heating plate –
on the heating plate. Remove with a
stainless steel cleaning agent.
3. Decalcifying is recommended
regularly, depending on water
hardness. Fill the kettle with water
and decalcifyer according to
decalcifyer product instructions.
Do not boil the solution as it could
foam over. Afterwards, rinse kettle
thorougly with fresh water.
Troubleshooting
EN
Problem
Possible cause
Solution
Too much lime scale at the heating element of
the kettle.
Run the decalcifying procedure.
Close lid until it locks.
The appliance cannot be switched on.
5
After operating with little or no water, the
Allow to cool a short time and try again.
Share more of our thinking at www.aeg.com
Download PDF

advertising