Electrolux EKM10760X User manual

Electrolux EKM10760X User manual
User manual
Cookers
Welcome to the world of Electrolux
Thank you for choosing a first class product from Electrolux, which hopefully will
provide you with lots of pleasure in the future.
The Electrolux ambition is to offer a wide variety of quality products that make your life
more comfortable.
Please take a few minutes to study this manual so that you can take advantage of the
benefits of your new machine.
We promise that it will provide a superior User Experience delivering Ease-of-Mind.
INSTRUCTIONS FOR THE INSTALLER: for the qualified technician who is in
charge of adequately checking the gas system, installing, commissioning and testing
the appliance.
INSTRUCTIONS FOR THE USER: include suggestions, the description of the controls
and the correct cleaning and maintenance operations for the appliance.
We were thinking of you
when we made this product
Contents
1. General information ______________________________________ 5
1.1
Technical service _________________________________________________________ 5
2. Warnings for safety and use ________________________________ 6
3. Installation______________________________________________ 8
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
General warnings _________________________________________________________ 8
Fitting the adjustable feet ___________________________________________________ 8
Electric connection ________________________________________________________ 9
Power consumption of the vitroceramic hob____________________________________ 11
Ventilation requirements___________________________________________________ 12
Gas connection__________________________________________________________ 12
Stability chain ___________________________________________________________ 13
Gas regulations _________________________________________________________ 15
Connecting to LPG _______________________________________________________ 15
4. Final operations ________________________________________ 16
4.1
Levelling the cooker to the floor _____________________________________________ 16
5. Description of controls ___________________________________ 17
5.1
The front panel __________________________________________________________ 17
6. Using the cooking hob ___________________________________ 23
6.1
6.2
Switching on the burners __________________________________________________ 23
Switching off the burners __________________________________________________ 23
7. Using the fry-top ________________________________________ 24
7.1
7.2
7.3
7.4
Before switching on the fry-top ______________________________________________
Switching on ____________________________________________________________
Energy regulator table ____________________________________________________
Switching off ____________________________________________________________
24
24
24
24
8. Using the vitroceramic hob ________________________________ 25
8.1
8.2
8.3
General warnings ________________________________________________________ 25
Switching on ____________________________________________________________ 25
Switching off ____________________________________________________________ 25
9. Using the ovens ________________________________________ 26
9.1
9.2
9.3
9.4
General warnings ________________________________________________________
Drawer ________________________________________________________________
Using the electric multifunction oven _________________________________________
Using the auxiliary oven with natural convection ________________________________
26
26
26
28
3
Contents
10. Cooking suggestions____________________________________ 29
10.1
10.2
10.3
10.4
Suggestions for using the hob burners correctly ________________________________
Suggestions for using the fry-top correctly _____________________________________
Suggestions for using the vitroceramic hob correctly _____________________________
Suggestions for using the oven correctly ______________________________________
29
29
29
29
11. Cleaning and maintenance _______________________________ 32
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
11.10
Cleaning stainless steel surfaces ____________________________________________
Cleaning enamelled surfaces _______________________________________________
Cleaning the polished surfaces _____________________________________________
Cleaning the knobs and the control panel _____________________________________
Cleaning the grids and burners _____________________________________________
Cleaning the igniter plugs and thermocouples __________________________________
Cleaning the fry-top ______________________________________________________
Cleaning the vitroceramic hob ______________________________________________
Cleaning the oven________________________________________________________
Replacing the oven light bulb _______________________________________________
32
32
32
32
32
33
33
33
34
34
12. Special maintenance____________________________________ 35
12.1
12.2
12.3
12.4
4
Removing the oven door __________________________________________________
Removing the side rack-holder frames ________________________________________
Removing and cleaning the inside oven fan ____________________________________
Adjustment of the drawer height_____________________________________________
35
36
36
36
Warnings
This user’s manual is an integral part of the product purchased. The user must conserve the manual
correctly so that it is always available for consultation during the use and maintenance of the
product. Keep this user’s manual for future reference. If the product is resold, the manual must be
transferred to any subsequent owner or user of the product.
The manufacturer is not liable for any inaccuracies in this booklet resulting from printing or
transcription errors. The manufacturer reserves the right to modify its products as it considers
necessary or in the interests of the user, without compromising their essential safety and operating
characteristics.
CLASSES OF APPLIANCES
The cooking appliances described in this operating manual belong to the following installation
classes:
•
Class 1: non-flush-mounted cooking appliance;
•
Class 2 – subclass 1: cooking appliance flush-mounted between two
units, made up of a single unit, but which can also be installed so that the
side walls are accessible.
1. General information
This product conforms to the requirements of the following European directives:
•
•
•
•
73/23/EEC for "Low Voltage".
89/336/EEC for "Electromagnetic Disturbance".
90/396/EEC for "Gas Appliances".
89/109/EEC for "Material in contact with Food".
The appliance complies with Directive 2002/95/EC (RoHS - Reduction of Hazardous
Substances) on restricting the use of hazardous substances in manufacturing materials.
1.1
Technical service
Before leaving the factory, this appliance has been tested and set up by qualified, specialist
personnel, so as to guarantee the best operating results. Each repair or adjustment that may
subsequently be necessary must be carried out with the utmost care and attention. We therefore
recommend always contacting the Dealer where the appliance was purchased or your nearest
Service Centre, specifying the type of problem and the appliance model.
5
Warnings
2. Warnings for safety and use
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT SHOULD BE KEPT IN GOOD CONDITION AND CLOSE
TO THE APPLIANCE FOR THE WHOLE LIFECYCLE OF THE COOKER. WE RECOMMEND READING THIS MANUAL
VERY CAREFULLY BEFORE USING THE COOKER. IN CASE AN ADDITIONAL JETS KIT IS GIVEN AS ACCESSORY
TO THE COOKER, WE RECOMMEND KEEPING AND PRESERVING IT. THE INSTALLATION MUST BE CARRIED OUT
BY QUALIFIED PERSONNEL AND IN COMPLIANCE WITH CURRENT STANDARDS. THIS APPLIANCE IS FOR
DOMESTIC USE AND CONFORMS TO THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT
FOR CARRYING OUT THE FOLLOWING FUNCTION: COOKING AND HEATING FOOD; ANY OTHER USE IS TO BE
CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ANY RESPONSIBILITY SHOULD THE APPLIANCE BE
USED FOR PURPOSES OTHER THAN THOSE INDICATED.
AT THE MOMENT OF PURCHASE, THE USER ASSUMES DIRECT RESPONSIBILITY FOR THE PRODUCT AND MUST
THEREFORE MAKE SURE THAT, WITH NORMAL USE, NO INSTABILITY, DEFORMATION, BREAKAGE OR WEAR
OCCURS OVER TIME THAT WOULD REDUCE PRODUCT SAFETY.
THIS PRODUCT IS DESIGNED AND MANUFACTURED TO OPERATE SAFELY AND DOES NOT POSE ANY DANGERS
TO PEOPLE, ANIMALS, AND OBJECTS.
DO NOT LEAVE ANY PIECES OF THE PACKING UNATTENDED IN THE HOME. SEPARATE THE VARIOUS PACKING
MATERIALS AND DELIVER THEM TO THE NEAREST RECYCLING CENTRE.
THE EARTH CONNECTION IS OBLIGATORY CONFORMING TO THE MODALITIES ENVISAGED BY THE SAFETY
STANDARDS OF THE ELECTRICAL WIRING SYSTEM.
THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND THE RELATIVE SOCKET MUST BE THE
SAME TYPE AND MUST COMPLY WITH CURRENT STANDARDS. AFTER INSTALLING THE APPLIANCE MAKE SURE
THAT THE PLUG IS ACCESSIBLE TO ALLOW THE PERIODICAL CHECK-UP.
DO NOT PULL OUT THE PLUG BY PULLING THE CABLE.
SHOULD THE GAS TAPS BE DIFFICULT TO ROTATE, LUBRICATE THEM USING A SPECIFIC PRODUCT FOR HIGH
TEMPERATURES.
CONTACT THE TECHNICAL SERVICE FOR THIS OPERATION.
IMMEDIATELY AFTER INSTALLATION, TEST THE APPLIANCE BRIEFLY BY FOLLOWING THE INSTRUCTIONS
SHOWN BELOW. IN THE EVENT OF A MALFUNCTION, DISCONNECT THE APPLIANCE FROM THE MAINS AND
CONTACT YOUR NEAREST TECHNICAL SERVICE CENTRE.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE.
EACH TIME YOU FINISH USING THE COOKING HOB, ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN "ZERO"
POSITION (OFF).
NEVER PUT INFLAMMABLE OBJECTS INTO THE OVEN: SHOULD IT BE ACCIDENTALLY SWITCHED ON, A FIRE
MAY BREAK OUT. IN THE EVENT OF A FIRE: CLOSE THE MAIN GAS SUPPLY AND CUT OFF THE ELECTRIC
CURRENT. DO NOT THROW WATER ON BURNING OR FRYING OIL. DO NOT STORE INFLAMMABLE OBJECTS OR
AEROSOL CANS NEAR THE APPLIANCE AND DO NOT SPRAY NEAR THE BURNERS WHEN SWITCHED ON. DO
NOT WEAR BAGGY CLOTHES OR ACCESSORIES THAT ARE NOT CLOSE TO THE BODY WHEN THE BURNERS
ARE SWITCHED ON: SERIOUS INJURIES CAN BE CAUSED BY BURNING FABRIC.
6
Warnings
DO NOT REST SAUCEPANS THAT DO NOT HAVE A PERFECTLY SMOOTH, EVEN BASE ON THE COOKING HOB.
DO NOT USE RECIPIENTS OR STEAK GRILLS THAT EXCEED THE OUTER PERIMETER OF THE COOKING HOB.
THE IDENTIFICATION PLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND THE MARK IS CLEARLY VISIBLE
ON THE BACK OF THE APPLIANCE.
THE PLATE MUST NEVER BE REMOVED.
THE APPLIANCE SHOULD ONLY BE USED BY ADULTS. DO NOT ALLOW CHILDREN TO APPROACH OR PLAY
WITH THE APPLIANCE. NEVER STORE ITEMS THAT CHILDREN MAY ATTEMPT TO REACH ABOVE THE
APPLIANCE. THE HEATING UP OF SOME PARTS OF THE APPLIANCE AND OF THE USED PANS MAY BE A
DANGER, SO DURING FUNCTIONING AND DURING ALL THE TIME NECESSARY FOR THE COOOLING DOWN, TAKE
CARE TO POSITION THE HOT PANS IN A WAY TO PREVENT BURNS OR OVERTURNING. AVOID LEAVING THE
OVEN DOOR OPEN DURING FUNCTIONING OR IMMEDIATELY SOON AFTER THE SWITCHING OFF. AVOID
TOUCHING THE HEATING ELEMENTS INSIDE THE OVEN AND GRILLS AS WELL.
RESTING OR SITTING ON THE OPEN OVEN DOOR, DRAWERS OR STORAGE COMPARTMENT CAN OVERTURN
THE APPLIANCE, AND CONSEQUENTLY CAUSE HARM. THE DRAWERS HAVE A DYNAMIC CAPACITY OF 25 KG.
IF THE COOKER IS SET ON A PEDESTAL, APPROPRIATE MEASURES MUST BE TAKEN TO PREVENT IT FROM
SLIDING OFF THE PEDESTAL.
WHEN THE APPLIANCE IS DECOMMISSIONED, IT MUST BE DISPOSED OF IN A SUITABLE RECYCLING CENTRE.
CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY
COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (DOORS, ETC.).
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL
AND ELECTRONIC EQUIPMENT (WEEE).
BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY, YOU WILL HELP PREVENT POTENTIAL NEGATIVE
CONSEQUENCES FOR THE ENVIRONMENT AND HUMAN HEALTH, WHICH COULD OTHERWISE BE CAUSED BY
INAPPROPRIATE WASTE HANDLING OF THIS PRODUCT.
ON THE PRODUCT, OR ON THE DOCUMENTS ACCOMPANYING THE PRODUCT, INDICATES
THE SYMBOL
THAT THIS APPLIANCE MAY NOT BE TREATED AS HOUSEHOLD WASTE. INSTEAD IT SHALL BE HANDED OVER TO
THE APPLICABLE COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT.
DISPOSAL MUST BE CARRIED OUT IN ACCORDANCE WITH LOCAL ENVIRONMENTAL REGULATIONS FOR WASTE
DISPOSAL. FOR MORE DETAILED INFORMATION ABOUT TREATMENT, RECOVERY AND RECYCLING OF THIS
PRODUCT, PLEASE CONTACT YOUR LOCAL CITY OFFICE, YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR
THE SHOP WHERE YOU PURCHASED THE PRODUCT.
The manufacturer declines any responsibility for damage incurred by persons or objects
that is caused by not following the above guidelines or by tampering with any part of the
appliance or by using non-original spare parts.
7
Instructions for the installer
3. Installation
DIMENSIONS OF THE COOKERS
3.1
General warnings
It is the law that a competent person installs all gas appliances. In the UK Corgi gas
installers are approved to work to safe and satisfactory standards. The cooker must be
installed in accordance with BS 6172. Failure to install the cooker correctly could invalidate
the warranty liability claims could and could lead to prosecution.
The manufacturer declines any responsibility for damage incurred by persons, animals or
objects that is caused by not following the above guidelines (cfr. chapter “2. Warnings for
safety and use”).
The technical data is indicated on the plate located on the back of the appliance. The adjustment
conditions are shown on a label applied to the packing and the appliance.
Do not use the oven door handle for handling the appliance, or for removing the appliance
from the packing.
3.2
Fitting the adjustable feet
Before turning the cooker over, we recommend removing all the parts that are not stably attached
to it, in particular the cooking hob grids and burners. To lighten the weight of the cooker, the
accessories inside the oven may also be removed, thereby preventing accidental damage during
the overturning operation.
The cooker is delivered with the feet removed. Before moving and hooking up the cooker, take the
feet from the packing and screw them onto the cooker. This can be done in one of two ways:
A
B
Lifting the cooker off the floor.
Laying the cooker on its back.
The final regulation of the feet to level the
cooker to the floor will be done after the
gas and electric hook-ups have been
made.
Should it be necessary to drag the cooker, screw the feet in completely and carry out the final
regulation only when the other operations are completed.
8
Instructions for the installer
3.3
Electric connection
Make sure that the voltage and the size of the mains corresponds to the specifications shown on
the plate located on the back of the appliance.
The plate must never be removed.
The plug at the end of the power supply cable and the wall socket must be the same type and must
comply with current electric standards. Check that the mains is adequately earthed. Once the
appliance has been installed make sure that the plug is accessible to allow the periodical check-up.
The power supply cable should conform to BS6004.
Prepare an omni-polar cutoff device on the power supply line of the appliance with a contact
opening distance equal to or more than 3 mm, located in a convenient position near the appliance.
Do not use reducers, adapters or shunts.
Before making the electric connection, make sure of the efficiency of the earthing.
Make sure that the relief valve and the home wiring system are able to withstand the appliance
load.
The yellow/green earth cable must not be subject to cutoffs.
The electric cable must not come into contact with parts whose temperature is more than 50°C
higher than room temperature.
The cooker should be installed in accordance with the latest edition of the IEE regulations.
3.3.1 Electric power cable section
According to the type of power supply, use a cable that conforms to the following table.
Running at 400V3N~ (models connected according to DIAGRAM
"A"): use a pentapolar cable type H05RR-F (cable measuring 5 x
2.5 mm2).
Running at 230V3~ (models connected according to DIAGRAM
"C" but commutated by the installer according to DIAGRAM
"B"): use a tetrapolar cable type H05RR-F (cable measuring 4 x 4
mm2).
Running at 230V1N~ (models connected according to DIAGRAM
"C"): up to 2.9 kW use a tripolar cable type H05RR-F (cable
measuring 3 x 1.5 mm2); between 2.9 kW and 5.4 kW use a tripolar
cable type H05RR-F (cable measuring 3 x 2.5 mm2); between 5,4
kW and 7 kW use a tripolar cable type H05RR-F (cable measuring 3
x 4 mm2); over 7 kW use a tripolar cable type H05RR-F (cable
measuring 3 x 6 mm2).
The end to be connected to the appliance must have the earth wire
(yellow-green) at least 20 mm longer.
9
Instructions for the installer
3.3.2 Type of power supply
It is possible to obtain different connections according to the voltage, simply by moving the
unconnected cable ends on the terminal board as shown in the following diagrams.
According to the model, consult the table "CONNECTION TO THE TERMINAL BOARD".
DIAGRAM “A”
DIAGRAM “B”
DIAGRAM “C”
CONNECTION TO THE TERMINAL BOARD
MODEL
POWER kW
POWER SUPPLY
COOKER 6 BURNERS (1 OVEN)
2,9
DIAGRAM “C”
COOKER VITROCERAMIC HOB (1 OVEN) (5 HEATING ELEMENTS)
12,7
DIAGRAM “A”
COOKER 6 BURNERS (2 OVENS)
3,9
COOKER 4 BURNERS (2 OVENS) + FRY-TOP
6,3
COOKER VITROCERAMIC HOB (2 OVENS) (5 HEATING ELEMENTS)
13,7
DIAGRAM “C”
DIAGRAM “A”
MODELS CONNECTED ACCORDING TO DIAGRAM "A" CAN BE COMMUTATED BY THE INSTALLER ACCORDING TO DIAGRAM
"B".
MODELS CONNECTED ACCORDING TO DIAGRAM "C" CAN BE COMMUTATED BY THE INSTALLER ACCORDING TO DIAGRAM
"A".
10
Instructions for the installer
3.3.3 Replacing the electric cable
To replace the electric cable, it is necessary to access the terminal board. It is located on the back
of the appliance, at the top left, as shown in the figure.
To replace the cable, proceed as follows:
•
•
•
•
•
•
open the terminal board box;
unscrew the screw A that locks the cable;
loosen the screw contacts and replace the cable
with one of the same length that corresponds to the
specifications in the table in section “3.3.1 Electric
power cable section”;
the "yellow-green" earth wire must be connected to
and must be approximately 20 mm
the terminal
longer than the line cables;
the neutral "blue" wire must be connected to the
terminal marked with the letter N;
the line wire must be connected to the terminal
marked with the letter L.
3.4
Power consumption of the vitroceramic hob
The vitroceramic hob has different power consumptions depending on the type of heating element
used. The diagram shows the values of the power consumed.
In the envisaged cases, the first numeric value refers to the total power, whereas the value that
follows the symbol "/" refers to the inside diameter, with the exception of the central heating
element, whose value that follows "/" refers to the outer diameter.
11
Instructions for the installer
3.5
Ventilation requirements
The room containing the appliances should have an air supply in accordance with B.S. 5440 part 2.
1.
All rooms require an opening window or equivalent, and some rooms will require a permanent
vent as well.
2.
For room volumes up to 5m³ an air vent of 100cm² is required.
3.
If the room has a door that opens directly to the outside, and the room exceeds 1m³ no air
vent is required.
4.
For room volumes between 5m³ and 10m³ an air vent of 50cm² is required.
5.
If there are other fuel burning appliances in the same room B.S. 5440 part 2 should be
consulted to determine the air vent requirements.
6.
The appliance must not be installed in a bed sitting room of less than 20m or in a bathroom or
shower room.
Windows and permanent vents should therefore not be blocked or removed without first consulting a
Corgi gas installer.
Failure to install appliances correctly is dangerous and could lead to prosecution.
DO NOT install LPG version below ground level. This does not exclude installation into a room, which
equates to a basement on one side of the building, but open to ground level on the opposite side.
3.6
Gas connection
Gas-powered devices for home use, which are not connected to a conduit for the evacuation of
combustion products, must not cause a concentration of carbon monoxide that could pose a health
risk to the persons exposed in relation to the time of exposure.
We recommend checking that the appliance is properly set up for the type of
gas distributed. The threaded ½" gas connection pipe is located at the rear
on the right hand side of the appliance.
AT
BE
CH
DE
DK
ES
FI
●
●
●
●
●
●
●
FR
GB
IE
IT
NL
NO
PT
SE
12
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Instructions for the installer
The cooker is designed to match the depth of standard 600mm worktops. An adaptor back plate
should, therefore, be fitted within the shaded area shown to allow the cooker to be pushed in fully
and chased to the wall.
Connection to the cooker should be made with an approved appliance flexible connection to
BS 669. A length of 0.9 to 1.25m is recommended. The length of hose chosen should be such that
when the cooker is in situ, the hose does not touch the floor.
The temperature rise of areas at the rear of the cooker that are likely to come in contact with the
flexible hose do not exceed 70°C.
3.7
Stability chain
The cooker is fitted with a stability device such as a
proprietary stability chain as shown and firmly secured to the
fabric of the building.
Whatever the position, remember to leave enough room for
the cooker to be pulled out for cleaning and service.
13
Instructions for the installer
The wall behind the cooker between the hotplate and 450mm above, and across the width of the
cooker, must be an incombustible material such as ceramic wall tiles.
This appliance is designed not to project in front of standard 600mm worktops (excluding handles).
To achieve the best fit the cooker must be pushed against the wall.
As this appliance is very heavy it should be situated on a suitably hard surface as to ensure
servicing and installation is made possible with minimal impact on the floor surface.
14
Instructions for the installer
3.8
Gas regulations
If the cooking appliance is set up for a different type of gas than that available, its injectors must
be replaced, the minimum flow regulated. In order to replace the injectors in the cooking hob, it is
necessary to carry out the following operations:
•
•
•
•
•
remove the pan supports;
remove the burners and burner caps (Fig. A);
take out the injector (Fig. B) and replace it with one
suitable for the new type of gas (see "GENERAL
INJECTORS TABLE" on page 16);
replace the gas label (on the rear of the appliance) with
the new one provided with the injectors kit;
refit all parts by following the disassembly instructions in
reverse order and taking care to position the burner cap
correctly on the burner.
3.8.1 Minimum flow of valved cooking hob taps
•
•
•
•
•
•
•
Switch on the burner and turn the control knob
towards the minimum flow position ;
remove the knob;
using a screwdriver, adjust the internal screw Z
until the correct low flame is obtained;
refit the knob.
Unscrew the adjustment screw Z to increase the flow, or tighten it to reduce the flow.
The adjustment is correct when the low flame measures approximately 3 or 4 mm.
When changing quickly from maximum to minimum flow and vice versa make sure that the
flame does not go out.
3.9
Connecting to LPG
Use a pressure regulator and connect to the cylinder in compliance with the guidelines set out in
standards regulations in force.
15
Instructions for the installer
The hob is made up of the 4 indicated modules:
• modules 1 and 4 are featured on all the
cookers;
• modules 2 and 3 are included depending on
which cooker is purchased and can be
replaced with electric modules (fry-top).
GENERAL INJECTORS TABLE
TYPE OF GAS
mBar
NATURAL GAS
20
LPG
BUTANE
PROPANE
30
28
37
NOZZLE NO.
115
97
72
128
94
85
65
50
93
68
BURNERS
POSITION TYPE
RAPID (A)
SEMI RAPID (B)
AUXILIARY (C)
TRIPLE-RING (D)
FISH KETTLE (E)
RAPID (A)
SEMI RAPID (B)
AUXILIARY (C)
TRIPLE-RING (D)
FISH KETTLE (E)
POWER Watt
MAX.
MIN.
3000
750
1750
480
1000
330
3300
1300
1900
750
3000
750
1750
480
1000
330
3300
1300
1900
750
CONSUMPTION
MAX.
286 l/h
167 l/h
95 l/h
314 l/h
181 l/h
219 g/h
128 g/h
73 g/h
241 g/h
138 g/h
4. Final operations
4.1
Levelling the cooker to the floor
After having made the electrical and gas hook-ups, level the cooker to the
floor using the adjustable feet that were previously screwed onto the bottom
of the cooker.
Should it be necessary to drag the cooker, screw the feet in completely and carry out the final
regulation only when the other operations are completed.
16
Instructions for the user
5. Description of controls
5.1
The front panel
All the commands and controls for the cooking hob and oven are on the front panel.
THE CONTROL PANEL
DESCRIPTION OF HOB BURNER KNOB
The flame is lit by simultaneously pressing and turning the knob anticlockwise to
the low flame symbol .
To regulate the flow of the flame, turn the knob to between the maximum and
minimum settings. Turn off the burner by returning the knob to position .
LAYOUT OF BURNERS – Description of symbols
REAR LEFT
REAR RIGHT
REAR CENTRE LEFT
REAR CENTRE RIGHT
CENTRE FRONT
CENTRE REAR
FRONT CENTRE LEFT
FRONT CENTRE RIGHT
FRONT LEFT
FRONT RIGHT
17
Instructions for the user
DESCRIPTION OF FRY-TOP CONTROL KNOB
The fry-top is equipped with differentiated heating. The entire cooking
surface can be used, or only one of the two halves, front or rear.
The knobs that regulate the energy individually control the temperature of the
two heating elements. A green light indicates that the appliance is heating.
LAYOUT OF HEATING ELEMENTS - Description of symbols
REAR
FRONT
DESCRIPTION OF VITROCERAMIC HOB KNOBS
Besides the normal knobs that regulate the energy, the
vitroceramic hob is equipped with knobs for differentiated
heating. Settings from 1 to 11 control the heating of the
internal element, setting the knob to the symbol
the
outer element also operates.
LAYOUT OF HEATING ELEMENTS - Description of symbols
REAR LEFT
REAR RIGHT
FRONT LEFT
FRONT RIGHT
CENTRAL
DESCRIPTION OF ELECTRIC OVEN KNOBS
The electric oven is controlled by two knobs: function
switch knob and thermostat knob. They allow you to
choose the most suitable type of heating for different
cooking requirements, by switching on the heating
elements appropriately and setting the required
temperature (from 50°C to MAX).
The V setting on the thermostat knob operates the oven fan.
Below the oven knobs there are two warning lights: the green light signals the oven is working; the
orange light indicates that the preset temperature has been reached. The orange light switches on
and off to indicate when the heating automatically kicks in to maintain the temperature inside the oven
at the level set on the thermostat knob.
The oven has an internal light. The light is always on while the oven is working: it can be switched
on while the oven is off, for cleaning purposes, by turning the function switch knob to the symbol
18
Instructions for the user
DESCRIPTION OF SYMBOLS ON THE FUNCTION SWITCH KNOB
SWITCH ON LIGHT INSIDE OVEN
GRILL-FAN ELEMENT
UPPER AND LOWER
HEATING ELEMENTS
UPPER AND LOWER
HEATING ELEMENTS – FAN
UPPER HEATING ELEMENT
HEATING ELEMENT-CONVECTION
LOWER HEATING ELEMENT
DEFROST
GRILL ELEMENT
DESCRIPTION OF AUXILIARY ELECTRIC OVEN KNOB
Some cooker models are equipped with an auxiliary electric oven with natural
convection, controlled by a single knob. This allows the user to choose the
most suitable type of heating for different cooking requirements, by switching
on the heating elements appropriately and setting the required temperature
(from 60 to MAX). Using the same knob it is also possible to set the functions
described in the table.
Below the auxiliary oven knob there is an orange light, which indicates when the oven has
reached the set temperature. The orange light switches on and off to indicate when the heating
automatically kicks in to maintain the temperature inside the auxiliary oven at the level set on the
control knob.
The auxiliary oven has an internal light. The light is always on while the oven is working: it can be
switched on while the oven is off, for cleaning purposes, by turning the function switch knob to the
symbol .
DESCRIPTION OF SYMBOLS ON AUXILIARY ELECTRIC OVEN KNOB
SWITCH ON LIGHT INSIDE OVEN
60÷MAX UPPER AND LOWER
UPPER HEATING ELEMENT
GRILL ELEMENT + SPIT
HEATING ELEMENTS
LOWER HEATING ELEMENT
19
Instructions for the user
THE ELECTRONIC TIMER
KEY
A
COOK TIME
B
END TIME
C
COUNTDOWN
D
TIME
E
DECREASE CONTROL
F
SELECTOR CONTROL
G
INCREASE CONTROL
The time of day must be set before the main oven
will operate manually.
SET THE TIME OF DAY
The oven has a 24 hour clock.
When the electricity supply is first switched ON, the
display will show 12.00 and the 'Time' ( ) indicator
neon will flash as Fig. 1.
To set the correct time press the increase control
button (+) and if necessary, the decrease control
button (-) until the correct time on the 24 hour clock
is reached, e.g. 10.00 a.m. as Fig. 2. The 'Time'
indicator ( ) neon will flash for 5 seconds and then
go out.
The increase and decrease control buttons operate
slowly at first, and then more rapidly. They should be
pressed separately.
HOW TO SET THE COUNTDOWN
The 'Countdown' gives an audible reminder at the
end of any period of cooking. This cooking period
may be up to 2 hrs 30 mins. It is not part of the
automatic control.
To set, press the Selector Control button ( ) until
the 'Countdown' indicator is illuminated ( ) the
display reads 0.00 as Fig. 3.
To set the correct time duration depress the
increase control (+) until the display indicates the
interval to be timed, e.g. 1hr 45 mins as Fig. 4. If
necessary depress the decrease control (-) to
achieve the correct time interval.
This must be completed within 5 seconds of first
pressing the Selector Control button.
During the operation of the 'Countdown', the
remaining time period will be shown in the display.
The 'Countdown' will sound intermittently for up to 2
minutes at the end of the timed period. The sound
can be stopped by pressing any button.
20
Instructions for the user
TO CANCEL THE COUNTDOWN
If you change your mind and want to cancel the
'Countdown', press the Selector Control button until the
'Countdown' indicator ( ) flashes and then the decrease
control (-) until 0.00 shows in the display as Fig. 5. The
'Countdown' indicator ( ) will continue to flash for a few
seconds and then return to the time of day.
SETTING THE OVEN TIMER CONTROL
The main oven can be automatically timed.
When using the timer control for the very first time, it is
advisable to let it operate while you are at home. The
displays can be checked to show that it is operating
correctly and you will feel confident to leave a meal to
cook automatically in the future.
A) TO SET THE TIMER TO SWITCH ON AND OFF
AUTOMATICALLY
i) Ensure the electricity supply is switched ON and that
the correct time of day is displayed, e.g. 9 a.m. as
Fig. 6.
ii) Place food in oven.
iii) To set the length of cooking time, press the Selector
control button ( ) until the 'Cook Time' indicator is
illuminated ( ). Press the increase control (+) until
the required length of cooking time is displayed, e.g.
2 hrs 15 mins as Fig. 7. If necessary depress the
decrease control (-) until the correct time interval is
achieved.
The maximum cooking time is 10 hours.
iv) Release the buttons. The 'Cook Time' indicator (
will be illuminated.
)
Remember, this must be completed within 5 seconds of
first pressing the Selector Control button.
v) To set the 'End Time'. Press the Selector Control
button until the 'End Time' ( ) flashes. Press the
increase control (+) until the required stop time is
displayed, e.g. 12.15 p.m. as Fig. 8. If necessary
depress the decrease control (-) until the correct
time interval is achieved.
vi) Release the buttons. The time of day will be
displayed after 5 seconds. The 'Cook Time' ( ) and
'End Time' ( ) indicators will be illuminated.
The 'End Time' must not be more than 23 hours 59
minutes from the time of day. For example, if the
time of day is 09.00 a.m., the latest 'End Time' would
be 08.59 a.m. the next day.
vii) Set the main oven control to the required
temperature. The oven indicator neon should be OFF.
When the automatic timed period starts, the oven
indicator neon will turn ON and OFF periodically during
cooking, showing that the temperature is being
maintained.
21
Instructions for the user
B) TO SET THE TIMER TO SWITCH OFF ONLY
i) Ensure the electricity supply is switched ON and that
the correct time of day is displayed, e.g. 10.00 a.m.
as Fig. 9.
ii) Place food in oven.
iii) To set the length of cooking time, press the Selector
Control button until the 'Cook Time' ( ) indicator is
illuminated. Press the increase control (+) until the
required length of cooking time is displayed, e.g. 2
hrs 15 mins as Fig. 10. Depress the decrease
control (-) if necessary.
iv) Release the buttons. The 'Cook Time' indicator ( )
will illuminate and the time of day will be displayed
after 5 seconds.
v) Set the oven temperature. The oven indicator neon
should be ON.
vi) To check the 'End Time' during the cooking period,
simply press the Selector Control button once and
the remaining time will be displayed, as Fig. 11.
TO CANCEL AN AUTOMATIC PROGRAMME
i) To cancel an automatic programme press the
Selector Control button until the 'Cook Time'
indicator ( ) neon flashes. Press the decrease
control (-) until the display reads 0.00 as Fig. 12.
ii) Release the buttons. The 'Cook Time' indicator ( )
will flash and after 5 seconds return to the time of
day.
iii) Turn off oven control.
TO RETURN THE APPLIANCE TO MANUAL
At the end of a timed cooking period, the indicator neon
will flash and an alarm will sound for up to 2 minutes.
i) To stop the sound press any of the three buttons, as
Fig. 13.
ii) The display will return to the time of day.
iii) Turn off the oven controls.
THINGS TO NOTE
In the event of an interruption of the electricity supply,
the timer will reset itself to zero, and all programming
will be cancelled.
AUTOMATIC COOKING
It is advisable to leave food in the oven for as short a
time as possible before automatic cooking. Always
ensure commercially prepared food is well within its use
by date and that home prepared food is fresh and of
good quality.
When cooking is complete, do not leave food to stand
in the oven, but remove and cool it quickly if the food is
not to be consumed immediately.
Always ensure food in the oven has been covered
before cooking if it is not possible to remove food
immediately after cooking.
22
Instructions for the user
6. Using the cooking hob
Make sure that the flame caps, the burner caps and the pan supports are fitted correctly.
During normal operations, the appliance heats up considerably. Caution should therefore be used.
Do not allow children to approach the appliance. Do not leave the cooking hob unattended
while it is on.
6.1
Switching on the burners
All the hob burner knobs have the following symbols:
tap closed
high flame
low flame
The low flame setting is found by turning the knob anticlockwise all the way. All intermediate settings
must be selected between the high flame and low flame, never between high flame and closed.
6.1.1 One-touch lighting
The hob burners are equipped with a "one-touch" lighting system. To switch on one of the burners,
press the knob corresponding to the required burner and turn it anticlockwise to the low setting .
Hold down the knob to activate the automatic "one-touch" lighting system. When the burner is on,
hold down the knob for approximately 10 seconds, to allow the safety valve to open. In the event
of a power cut, the burner can also be lit with a match (see section “6.1.2 Manual lighting”).
Should the burner switch off accidentally, the safety thermocouple blocks the gas flow, even when
the tap is open.
The device should not been activated for longer than 15 seconds. If after that time it fails to
operate stop pressing the knob, open the window and wait 1 minute before trying again. In case
the flame goes out accidentally turn off the knob and do not try to switch on the burner for at least
1 minute.
6.1.2 Manual lighting
To light one of the burners, move a lit match towards the burner, press the corresponding knob and
turn it anticlockwise to the minimum setting . Release the knob.
6.2
Switching off the burners
At the end of the cooking, return the knob to position .
23
Instructions for the user
7. Using the fry-top
During normal operations, the appliance heats up considerably. Caution should therefore be used.
Do not allow children to approach the appliance. Do not leave the fry-top unattended while it is
on.
When using the burners we recommend removing the safety cover A (only available on certain models).
7.1
Before switching on the fry-top
The first time it is used, the fry-top griddle may develop an acrid or burnt smell caused by oily
residue from manufacturing that may give unpleasant odours or flavours to food. To eliminate this
problem, clean the griddle as described in section “11.7 Cleaning the fry-top” before use.
7.2
Switching on
The fry-top is equipped with differentiated heating. The entire surface of the griddle can be used,
or only one of the two halves, front or rear.
Position the control knob of the heating element to the required setting. The green light switches
on to indicate the appliance is working. Place the food on the griddle and cook as preferred.
7.3
Energy regulator table
The following table offers only indicative values because, according to the thickness and type of
food, as well as personal taste, the heat should be higher or lower.
1-4
Maintaining the heat on the griddle
5-7
For light cooking
8-9
To grill
10 - 11
11
7.4
To grill thicker meat
For rapid warming and cleaning
Switching off
After cooking, return the knob to position .
24
Instructions for the user
8. Using the vitroceramic hob
During normal operations, the appliance heats up considerably. Caution should therefore be used.
Do not allow children to approach the appliance. Do not leave the vitroceramic hob unattended
while it is on.
8.1
General warnings
The first time it is heated, the vitroceramic hob may develop an acrid or burnt smell caused by oily
residue from manufacturing, which disappears completely after repeated use.
The vitroceramic hob is fitted with a cooking area with various diameters and power (see section
“3.4 Power consumption of the vitroceramic hob”). Their position is clearly indicated with circles
and the heat is delimited within the diameters marked on the glass.
8.2
Switching on
Position the pan or pot with the food to be cooked inside it on the required heating element.
Turn the energy regulator knob to the required setting. After a few moments, the latent heat light
corresponding to the selected heating element switches on.
If the vitroceramic hob is used to boil water, once it has boiled, turn the energy regulator knob to a
lower setting to prevent the liquid in the pot from boiling over and soiling the surface.
Some knobs are fitted with a supplementary heating setting (griddle with dual heating
element). To activate it, turn the energy regulator knob to position .
8.3
Switching off
After cooking, return the knob to position .
The vitroceramic hob features a latent heat light which
reproduces in reduced scale the position of the heating
diameters. This light signals that the surface area is still hot.
Do not clean or touch the surface until the latent heat light has switched off.
25
Instructions for the user
9. Using the ovens
9.1
General warnings
When the oven or grill is operating, the outer walls and oven door can become very hot.
Keep children away from the appliance.
Do not allow children to sit on the oven door or play with it.
Do not use the door as a stool.
Never stand aluminium pots or foil on the base of the oven, as this may seriously damage
the oven enamel.
Do not cook food on the bottom of the oven.
When using the oven for the first time, or after a power cut, the display flashes regularly indicating
. To set the display, refer to section "SET THE TIME OF DAY” on page 20.
Do not attempt to disassemble the oven door without consulting the relative instructions carefully
(refer to section “12.1 Removing the oven door”): the hinges on the oven door may injure the
hands.
HEATING BLOCK OF THE OVEN
If during normal operation the oven interrupts heating and the programmer display begins to flash
and goes to zero, check whether:
•
there has been a current interruption.
If the block occurs again after the cooking programme has been restarted, this means that the
safety device has been tripped. This device intervenes in the event of a thermostat fault and
prevents oven overheating. In such case, we recommend that you not try to light the oven again
and that you contact your nearest service centre.
9.2
Drawer
A storage drawer is provided on the lower part of the cooker
beneath the oven. Use only to store metal cooker accessories.
Do not store inflammable material such as cloths, paper or similar in the drawer.
9.3
Using the electric multifunction oven
The end of cooking display and the control knobs on the main oven
have no bearing on the operation of the auxiliary oven.
9.3.1 Switching on the oven for the first time
The first time it is used, the oven may smoke or give off
an acrid smell caused by oily residue from manufacturing
that may give unpleasant odours or flavours to food.
Before putting food in the oven, heat to the maximum
temperature for 30-40 minutes with the door closed
and wait until the smoke or odour has stopped.
26
Instructions for the user
To prevent any steam in the oven from scalding, proceed as follows:
turn the function switch knob to "0", or to function ; open the door in
two stages: hold it partly open (approx. 5 cm) for 4-5 seconds, then
open it completely.
Should you need to adjust the food, leave the door open for as short a
time as possible to prevent the temperature inside the oven from
lowering to such an extent as to jeopardise cooking.
9.3.2 Traditional cooking
Turn the function switch knob to position
and the thermostat knob in correspondence with the
required temperature value. For differentiated heating over or below the food, set the function
selector switch to position
(hot above) or
(hot below). For more uniform heating throughout
the oven, turn the function switch knob to position .
After preheating and putting the food in the oven an air flow between the upper side of the door and
the lower side of the hob may be noticed. In case that does not happen, switch off the
appliance and contact the Technical Service immediately.
9.3.3 Convection cooking
Turn the function switch knob to position
required temperature value.
; turn the thermostat knob in correspondence with the
9.3.4 Cooking with the ventilated grill
Turn the function switch knob to position
maximum temperature value (MAX).
; turn the thermostat knob in correspondence with the
9.3.5 Cooking with the grill + roasting spit
Turn the function switch knob to position ; turn the thermostat knob in correspondence with the
maximum temperature value (MAX). The grill and spit operate at the same time, allowing for
cooking on the spit.
9.3.6 Cooking with the roasting spit
If your oven model has a roasting spit, proceed as follows:
•
•
•
•
•
•
Slide the meat to be cooked on the spit rod A and secure it with the adjustable forks.
Hang the hook B at the top of the oven as shown in the figure.
Place the spit rod A into the hole C in the oven casing; before closing the oven door, make
sure that the rod A is correctly inserted into the hole C (insert the rod and turn it slightly back
and forth).
Hang the other end of the spit rod to the hook B (the
pulley of the rod A is situated on the handle of the
hook B).
Close the oven door and activate the spit by turning
the function selector knob to the
position.
When cooking is completed, open the oven door and
remove the spit rod using the plastic handle D, which
is screwed into the base of the rod A.
9.3.7 Defrosting
Turn the function switch knob to position , turn the thermostat knob to position "0": in this way the
motor fan is activated, which moves the air inside the oven and encourages frozen food to defrost.
9.3.8 Switching off the oven
The oven is switched off by returning the thermostat knob to position "0".
27
Instructions for the user
9.4
Using the auxiliary oven with natural convection
The end of cooking display and the control knobs on the main oven
have no bearing on the operation of the auxiliary oven.
The auxiliary oven with natural convection is equipped with:
•
•
a heating element positioned on the base of the oven (at the bottom);
a heating element positioned on the ceiling of the oven (at the top) +
grill.
9.4.1 Switching on the auxiliary oven for the first time
The first time it is used, the auxiliary oven may smoke or give off an acrid smell caused by oily
residue from manufacturing that may give unpleasant odours or flavours to food. Before putting
food in the oven, heat the auxiliary oven to the maximum temperature for 30-40 minutes with
the door closed and wait until the smoke or odour has stopped.
To start heating the auxiliary oven, select the temperature (from 60 to MAX) or the required
function by turning the thermostat knob.
9.4.2 Cooking with the grill (auxiliary oven)
Turn the thermostat knob to position
and let the auxiliary oven preheat for approximately 5
minutes. For correct operations, position the grill shelf on the third guide from the bottom. It is
however possible to vary the position of the grill shelf according to personal taste and different
cooking requirements. Before putting food in the oven, allow it to preheat for 5 minutes. A cooling
system prevents the control knobs from overheating.
9.4.3 Cooking with the spit (auxiliary oven)
Turn the thermostat knob to position
and let the auxiliary oven preheat for approximately 5
minutes. In the meantime, proceed as follows:
•
•
•
•
•
•
insert the food on to the spit rod A taking care to hold it firm with the two forks B, and balancing
it so as to avoid straining the gearmotor;
place the pulley C of the spit rod onto the support D after
introducing the opposite end into the hole E, until the coupling with
the gearmotor F so that the rod rotates;
pour a little water into the dripping pan and position it under the spit
rod;
monitor the cooking from time to time and check the spit rod is
rotating correctly;
at the end of the cooking, switch off the auxiliary oven by returning
the thermostat knob to position "0";
remove the spit rod from the auxiliary oven using the knob G and
wearing an oven glove.
9.4.4 Switching off the auxiliary oven
The oven is switched off by returning the thermostat knob to position "0".
28
Instructions for the user
10. Cooking suggestions
10.1 Suggestions for using the hob burners correctly
The diameter of the base of cooking recipients
should fit the diameter of the burner used (see
adjacent table). The burner flame must never be
wider than the diameter of the recipient. Use
recipients with a flat base. Where possible use
pots with a lid, as this allows less power to be
used. To reduce cooking times for vegetables,
potatoes, etc., use little water.
Burner
Rapid
Semi rapid
Auxiliary
Triple-ring
Fish kettle
Recipient diameter
(in cm)
from 24 to 26
from 16 to 22
from 8 to 14
from 24 to 26
from 16 to 35
10.2 Suggestions for using the fry-top correctly
Foods cooked on the fry-top have a special taste that does not require the excessive use of spices.
It is possible to cook in different ways. For example, different foods, such as meat and fish, can be
cooked at the same time. Before cooking meat, we recommend treating it with flavoured oil or
marinating it for a few hours.
A little tip: meat should always be salted after cooking on the griddle, so that its juices do not come
out prematurely.
10.3 Suggestions for using the vitroceramic hob correctly
In order to obtain good efficiency and adequate energy consumption, it is essential to use only
recipients that are suitable for electric cooking. The diameter of the base of the recipient must be
the same as the diameter of the outline of the cooking area. Energy is wasted if they do not
correspond.
The base of the recipient must be very thick and perfectly flat. It should also be clean and dry, as
should the glass on the hob.
Do not use cast iron pots or pots with a rough base, as they may scratch the surface.
When using the vitroceramic hob, it must be thoroughly cleaned before switching on the heating
elements.
The glass may be scratched if pans are placed on abrasive residues. Any scratches do not
however jeopardise the cooking procedure.
The ideal thickness for the base of the pans is:
•
2-3 mm in enamelled steel;
•
4-6 mm in stainless steel with double base.
Before cooking food with a high sugar content (e.g. jam), apply a protective product to the cooking
surface to prevent it from being damaged if the food spits or boils over.
10.4 Suggestions for using the oven correctly
The oven allows to optimise cooking. It is possible to cook traditionally, with convection and with
the grill.
The oven door should be completely closed for all types of cooking.
29
Instructions for the user
10.4.1 Traditional cooking
With this type of cooking, the heat comes from the top and the bottom. It is therefore preferable to
use the central guides. If the cooking requires a hotter temperature from the bottom or from the top,
use the lower or upper guides. Traditional cooking is recommended for all food that requires high
cooking temperatures, or long brazing times. This system is also recommended when cooking with
recipients made of terracotta, porcelain and similar materials.
10.4.2 Convection cooking
With this type of cooking, the food is heated by preheated air that is circulated in the oven thanks to
a fan located on the rear wall of the oven. Heat rapidly and evenly reaches all parts of the oven,
thus enabling different food to be cooked at the same time on different shelves. Humidity is
eliminated from the air and the drier area prevents odours and flavours from being spread and
mixed.
The possibility of cooking on more than one shelf allows you to cook many different dishes at the
same time. Biscuits and mini pizzas can be cooked in three different baking tins. The oven,
however, can also be used for cooking on a single shelf. The lower shelves can be used so that it
is easier to monitor cooking.
Convection cooking is particularly convenient for bringing frozen food rapidly back to room
temperature, for sterilising preserves or home-made fruit in syrup and, finally, for drying
mushrooms or fruit.
10.4.3 Cooking with the grill
The heat comes from the top. Almost all meat can be grilled, with the exception of lean game and
dishes such as meat-loaf. Meat and fish to be grilled should be lightly drizzled with oil and placed
on the grid bars, which should be placed in the guides closest to or farthest away from the grill
element, depending on the thickness of the meat, so as to avoid burning the surface and cooking
too little inside.
Suitable for: relatively thin meat; toasted sandwiches.
Pour 1 or 2 glasses of water into the dripping pan to avoid smoke forming due to drops of juice or fat.
While cooking with the grill, the dripping pan should always be positioned in the 1st guide from the
bottom.
10.4.4 Cooking with the ventilated grill
Using the combination of grill and fan .
This type of cooking allows the heat to penetrate gradually inside the food, even though the surface
is directly exposed to the grill.
Suitable for: thicker meat; game-birds.
10.4.5 Cooking meat and fish
Meat to be cooked in the oven should weigh at least 1 kg. Very tender red meat to be cooked rare
(roast beef, fillet, etc.), or which should be well cooked on the outside and preserve all its juices on
the inside, require cooking on high temperatures for a short time (200-250°C). White meat, gamebirds and fish require cooking on low temperatures (150-175°C).
The ingredients for the sauce should only be placed in the baking tin if the cooking time is short,
otherwise, they should be added in the last half hour. Meat can be placed on an ovenproof plate or
directly on the grid bars, below which the dripping pan should be placed to collect the juice. Press
the meat with a spoon to check if it is done. If it is firm, it is cooked.
At the end of the cooking, wait at least 15 minutes before cutting the meat so as not to lose the
juices. Before serving, plates can be warmed in the oven at minimum temperature.
10.4.6 Baking
Beaten mixtures must stick to the spoon because excess fluidity would prolong the cooking time.
Sweets require moderate temperatures (generally between 150-200°C) and require preheating
(approximately 10 minutes). The oven door must not be opened until at least ¾ of the way
through the cooking time.
30
Instructions for the user
10.4.7 Recommended cooking tables
Cooking times vary according to the nature, homogeneity and volume of the food. We recommend
monitoring your first attempts and checking the results, as similar results are obtained by cooking
the same dishes in the same conditions. The following three tables (I, II and III) provide guidelines.
TABLE OF CONVECTION AND TRADITIONAL COOKING TIMES (I)
TYPE OF COOKING
QUANTITY
KG.
BAKING
WITH BEATEN MIXTURE, IN A TIN
WITH BEATEN MIXTURE, ON THE DRIPPING PAN
SHORT PASTRY, PIE BASE
SHORT PASTRY WITH MOIST FILLING
SHORT PASTRY WITH DRY FILLING
MIXTURE WITH NATURAL LEAVENING
SMALL CAKES
MEAT
VEAL
BEEF
ENGLISH STYLE ROAST BEEF
PORK
CHICKEN
STEWS
BEEF STEW
VEAL STEW
FISH
FILLET, STEAK, COD, HAKE, SOLE
MACKEREL, TURBOT, SALMON
OYSTERS
TIMBALE
PASTA TIMBALE
VEGETABLE TIMBALE
SWEET AND SAVOURY SOUFFLÉS
PIZZA AND CALZONE
•
•
•
•
POSITION OF GUIDE
FROM BOTTOM
CONVECTION
TRADITIONAL
TEMPERATURE
°C
CONVECTION
TRADITIONAL
TIME IN
MINUTES
1
1
0.5
1.5
1
1
0.5
1-3
1-3
1-3
1-3
1-3
1-3
1-3
2
2
3
2
2
1
3
175
175
175
175
175
175
160
200
200
200
200
200
200
175
60
50
30
70
45
50
30
1
1
1
1
1-1.5
2
2
2
2
2
2
2
2
2
2
180
180
220
180
200
200
200
220
200
200
60
70
50
70
70
1
1
1
1
2
2
175
175
200
200
120
110
1
1
1
1-3
1-3
1-3
2
2
2
180
180
180
180
180
180
30
45
20
2
2
0.75
0.5
1-3
1-3
1-3
1-3
2
2
2
2
185
185
180
200
200
200
200
220
60
50
50
30
The times refer to cooking on one shelf only; for more than one shelf increase the time by 5-10'.
The cooking times do not include preheating which takes approximately 15'.
When cooking on more than one shelf, the guides are given in the preferential position.
For beef, veal, pork and turkey roasts, either with bone or rolled, increase the time by 20'.
TABLE OF COOKING TIMES WITH GRILL AND VENTILATED GRILL (II)
TRADITIONAL GRILLING
TYPE OF COOKING
CHICKEN
TOASTED SANDWICHES
SAUSAGES
PORK CHOPS
FISH
QUANTITY
KG.
1-1.5
0.5
0.5
0.5
0.5
POSITION OF GUIDE
FROM BOTTOM
3
4
4
4
4
TEMPERATURE
°C
MAX
MAX
MAX
MAX
MAX
TIME IN
MINUTES
30 PER SIDE
5 PER SIDE
10 PER SIDE
8 PER SIDE
8 PER SIDE
QUANTITY
KG.
1.5
1.5
1.2
POSITION OF GUIDE
FROM BOTTOM
2
3
2
TEMPERATURE
°C
170
220
190
TIME IN
MINUTES
180
60
90
GRILLING WITH VENTILATED GRILL
TYPE OF COOKING
ROAST PORK
ROAST BEEF
CHICKEN
•
st
The dripping pan for collecting cooking juices should always be positioned in the 1 guide from the bottom.
TABLE OF DEFROSTING TIMES (III)
DEFROSTING
TYPE OF FOOD
READY-TO-EAT DISHES
MEAT
MEAT
MEAT
•
QUANTITY
KG.
1
0.5
0.75
1
POSITION OF GUIDE
FROM BOTTOM
2
2
2
2
TIME IN
MINUTES
45
50
70
110
Defrosting at room temperature has the advantage of not modifying the flavour and appearance of food.
31
Instructions for the user
11. Cleaning and maintenance
Before cleaning or carrying out maintenance, switch off the power supply to the appliance
and close the gas tap.
Warning: Servicing should be carried out only by authorised personnel.
Do not clean the surfaces of the appliance when they are still hot.
Do not use pressure or steam spray guns to clean the appliance.
11.1 Cleaning stainless steel surfaces
To clean and preserve the stainless steel surfaces and remove the toughest stains, always use
specific products, provided they do not contain chlorine-based abrasives or acid substances,
or a little warm vinegar.
Pour the product onto a damp cloth and wipe the steel surface. Rinse carefully and dry with a soft
cloth or a piece of deerskin.
Do not under any circumstances use metallic sponges or sharp scrapers that may damage
the surfaces. Only use non-scratch, non-abrasive sponges and, if necessary, wooden or plastic
utensils.
11.2 Cleaning enamelled surfaces
Clean with a non-scratch, non-abrasive sponge dampened with soap and water. Grease stains
can easily be eliminated with hot water or a product specifically made for cleaning enamel. Rinse
carefully and dry with a soft cloth or a piece of deerskin.
Do not use products containing abrasives, scouring pads, steel wool or acid, which may
spoil the surfaces. Do not leave acid or alkaline substances on the enamel (lemon juice, vinegar,
salt, etc.).
11.3 Cleaning the polished surfaces
Clean with a non-abrasive, scratchproof sponge dampened with warm water and neutral soap or
with a standard detergent for polished surfaces. Rinse and dry carefully with a soft cloth.
Abrasive pastes, coarse wire pads, steel wool or acid will damage the surfaces. Do not use
alcohol.
11.4 Cleaning the knobs and the control panel
Clean the knobs and the control panel with a damp cloth.
11.5 Cleaning the grids and burners
To clean the grids and hob burners, remove them from
their housing by lifting them upwards as shown in the
figure, and immerse them in a solution of warm water
and non-abrasive detergent for about ten minutes.
Rinse and dry carefully.
Always check that none of the burner openings is
clogged.
Be sure to refit the burner correctly, checking the flame
is uniform.
We recommend carrying out this operation at least once
a week and each time it is necessary.
32
Instructions for the user
11.6 Cleaning the igniter plugs and thermocouples
In order for the igniter plugs and thermocouples to operate correctly, they
must be kept clean at all times. Check them frequently and, if necessary,
clean them with a damp cloth. Any dry residue should be removed with a
toothpick or needle, taking care not to damage the insulating ceramic part.
11.7 Cleaning the fry-top
Any grease deposits on the fry-top can be eliminated more easily when the griddle is still warm. If
necessary, leave it to cool and soak for a few minutes. Finally, clean with warm salted water, dry
with a tea cloth or kitchen roll.
After each use, the vitroceramic surface V underneath the fry-top should also be cleaned. Any
residue of meat or grease can be removed by proceeding as follows:
•
•
•
•
•
remove the fry-top from its housing;
turn the knob to position 11;
after approximately 20-30 minutes, even the
toughest residue can easily be cleaned off the
vitroceramic surface with a wooden spatula;
switch off the heating and leave to cool, then
clean the vitroceramic surface V with specific
products;
dry thoroughly and return the fry-top to its
working position.
11.8 Cleaning the vitroceramic hob
The vitroceramic hob must be cleaned regularly, each time it is used if possible, when the latent
heat lights are off.
Any light-coloured marks caused by aluminium-based pans can be removed with a damp cloth
dipped in vinegar.
Any burnt residue left after cooking can be removed with a wooden spatula. Rinse with water and
dry well with a clean cloth.
Do not under any circumstances use abrasive or corrosive detergents (e.g. powder products,
oven sprays, stain-removers or metallic sponges).
Any grease deposits on the vitroceramic hob
can be removed more easily by heating it for
approximately 20-30 minutes (knob in
position 11). Afterwards, this residue can be
cleaned off with a wooden spatula. Allow the
surface to cool, rinse with water and dry well
with a clean cloth.
In the event that aluminium or plastic marks, sugar or food containing sugar melt on the cooking
surface, remove immediately while the surface is still warm with a wooden spatula. This will
prevent any damage to the surface.
The cooking surface of the vitroceramic hob is extremely resistant. It is not however unbreakable
and may be damaged, above all by pointed or hard objects if dropped onto it with a certain force.
Warning! If any crack should appear on the hob, isolate the cooker from the main supply
and do not use the appliance to avoid electrocution. Call Customer Services immediately.
33
Instructions for the user
11.9 Cleaning the oven
In order to preserve the oven well, it should be cleaned regularly, each time it is used if possible,
after leaving it to cool: in this way it is possible to remove any residue more easily, preventing it
from burning the next time the oven is used.
Clean the stainless steel parts and enamelled parts as described in the corresponding sections
“11.1 Cleaning stainless steel surfaces” and “11.2 Cleaning enamelled surfaces”.
Take out all the removable parts and wash them separately. Rinse and dry thoroughly with a clean
cloth.
11.9.1 Cleaning the oven walls
Never use detergent products to clean this type of oven.
The walls of the oven can be cleaned using white vinegar and wiped with a cloth dampened with
water. Subsequently, heat the oven for at least one hour at 150°C to facilitate cleaning. When the
oven has cooled, wipe it again with a damp cloth.
11.9.2 Cleaning the oven door
We recommend always keeping the oven door clean. Use kitchen roll and on tougher dirt use a
damp cloth and household detergent.
Spray products for cleaning the oven must not be used to clean the fan and the thermostat
sensor inside the oven compartment.
11.10 Replacing the oven light bulb
Before carrying out maintenance, switch off the power supply to the appliance.
Proceed as follows:
• open the oven door;
• unscrew the glass safety cap anticlockwise; unscrew the bulb and
replace it with another one for high temperatures (300°C) with the
following characteristics:
Voltage:
230 V / 50 Hz
Power:
15 W
Attachment: E 14
•
34
Refit the glass cap and switch on the power. It is possible to check that the oven light is
working even when the door is closed by turning the function switch knob to position .
Instructions for the user
12. Special maintenance
Periodically, it is necessary to maintain or replace some parts that are subject to wear and tear.
Specific instructions are given below for each type of maintenance.
Before carrying out maintenance, switch off the power supply to the appliance and close the
gas tap.
12.1 Removing the oven door
The oven door can be completely removed to enable more thorough cleaning. Though this
operation is possible, it should not be performed by everyone, as it requires the strength to hold up
the door and a minimum of expertise to re-fit it. If you are not sure of being able to do this, we
recommend that you clean the door without taking it off or, in special cases, that you contact the
nearest authorised service centre.
To remove the door, proceed as follows:
•
•
•
•
Open the oven door and release the safety catches of the hinges by turning the respective pins
A (one for each hinge) backward.
Partially close the door until there is no more load tension on the springs (the door will form an
angle of about 30°).
Using both hands, accompany the movement of the door towards closure and simultaneously
lift it upward.
Turn the lower part of the door towards the outside to free the hinges B from their seats.
If you need to remove any dry residues or dust deposited on the inner part of the windows, turn the
door upside down as shown in the figure, slide a soft bottle brush into the spaces between the
glass plates and brush gently.
To re-fit the door, carry out the instructions given above in the inverse direction. When the hinges B
are back in their seats, open the door all the way and re-fit the safety catches of the hinges,
lowering the respective pins A (one for each hinge).
CAUTION: After re-fitting the door, always be sure to re-fit the hinge safety
catches.
35
Instructions for the user
12.2 Removing the side rack-holder frames
The rack-holder frames can be removed to clean them separately and to facilitate cleaning the
oven walls. The frames are hooked to the oven wall in the three points indicated by the arrows in
the figure (detail 1).
•
•
Press downward with your fingers as shown in detail 2 of the figure to release the frame from
the upper pin.
Lift the frame upward and take it out.
To re-fit proceed in the inverse direction. Set the lower part of the frame on the respective pins and
press the upper part against the oven wall until it hooks onto the pin.
12.3 Removing and cleaning the inside oven fan
The inside fan of the ventilated oven may require periodic cleaning. To disassemble the fan
proceed as follows:
•
•
•
•
•
•
Make sure that the power supply to the appliance is switched off.
Remove all inside components (dripping pan, shelves).
Loosen and remove the four screws A from the cover panel.
Remove the cover panel B.
Use a coin to loosen the fixing nut C of the fan (this threading is inverse; to loosen turn
clockwise).
Remove the fan D and wash it by
immersing it in warm water and dish
detergent. Never use abrasive or
corrosive
detergents,
powdered
products, or metal scrubbers. Rinse the
fan and dry it thoroughly.
Re-fit the fan and the cover by working in the
inverse direction to the instructions for removal.
12.4 Adjustment of the drawer height
The clips of height adjustment are located in the
lower side and at the right and left ends of the
drawer.
•
36
By turning the lever A the drawer will raise
of 3 mm.
Notes
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Notes
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
B00090 ZS3418 01/08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement