JOHN LEWIS JLV09 User Manual

Add to My manuals
32 Pages

advertisement

JOHN LEWIS JLV09 User Manual | Manualzz
JLDV 09
Tumble Dryer
Instruction manual
Important safety information
It is most important that this instruction book should be retained with
the appliance for future reference. Should the appliance be sold or
transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance
and the relevant warnings.
These warnings have been provided in the interest of safety. You MUST
read them carefully before installing or using the appliance. If you are
unsure of the meanings of these warnings contact the John Lewis branch
from which you purchased the appliance.
• Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
• Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
• In order to avoid danger of fires caused by
excessive drying, do not use appliance to
dry the following items; cushions, quilts etc
and the like (these items accumulate heat).
• Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted
with foam rubber pads should not be dried
in the tumble dryer.
• Always unplug the appliance after use, clean
and maintenance.
• Under no circumstances should you
attempt to repair the machine yourself.
Repairs carried out by inexperienced
persons may cause injury or serious
malfunctioning. Contact your local Service
Centre. Always insist on genuine spare
parts.
Important! In the interest of your
safety and to ensure the correct use,
before installing and first using the
appliance, read this user manual
carefully, including its hints and
warnings. To avoid unnecessary
mistakes and accidents, it is important
to ensure that all people using the
appliance are thoroughly familiar with
its operation and safety features. Save
these instructions and make sure that
they remain with the appliance if it is
moved or sold, so that everyone using
it through its life will be properly
informed on appliance use and safety.
General safety
• It is dangerous to alter the specifications or
attempt to modify this product in any way.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or lack of experience and
knowledge, unless they have been given
supervision or instructions concerning the
use of the appliance by a person
responsible for their safety.
2
• Items that have been soiled with substances
such as cooking oil acetone, petrol,
kerosene, spot removers, turpentine,
waxes and wax removers should be
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
• Danger of explosion: Never tumble dry
items that have been in contact with
inflammable solvents (petrol, methylated
spirits, dry cleaning fluid and the like). As
these substance are volatile, they could
cause an explosion. Only tumble dry items
washed with water.
• Risk of fire: items that have been spotted
or soaked with vegetable or cooking oil
constitute a fire hazard and should not be
placed in the tumble dryer.
• If you have washed your laundry with stain
remover you must execute an extra rinse
cycle before loading your tumble dryer.
• Please make sure that no gas lighters or
matches have accidentally been left in
pockets of garments to be loaded into
appliance
Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this
is not adhered to. See relevant section in
the user manual.
• Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
• Care must be taken to ensure that the
appliance does not stand on the electrical
supply cable.
• If the machine is situated on a carpeted
floor, please adjust the feet in order to
allow air to circulate freely.
• After having installed the appliance, check
that it is not pressing or standing on its
electrical supply cable or/and inlet hose.
• If the tumble dryer is placed on top of a
washing machine, it is compulsory to use
the stacking kit (optional accessory).
Warning! Never stop a tumble
dry before the end of the drying
cycle unless all items are quickly
removed and spread out so that
the heat is dissipated. Risk of fire!
Use
• This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
• Only wash fabrics which are designed to be
machine dried. Follow the instructions on
each garment label.
• Do not dry unwashed items in the tumble
dryer.
• Do not overload the appliance. See the
relevant section in the user manual.
• Clothes which are dripping wet should not
be placed in the dryer.
Warning! Risk of electric shock!
Do not spray down the appliance with
jets of water.
• The final part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure
that the items are left at a temperature that
ensures that items will not be damaged.
• Ensure you have adequate ventilation in the
installation room to avoid the back flow of
gases into the room from appliances
burning other fuels, including open fires.
3
• Garments which have been in contact with
volatile petroleum products should not be
machine dried. If volatile cleaning fluids are
used, care should be taken to ensure that
the fluid is removed from the garment
before placing in the machine.
• Never pull the power supply cable to
remove the plug from the socket; always
take hold of the plug itself.
• Never use the tumble dryer if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the tumble dryer is not accessible.
• Fabric softeners, or similar products should
be used as specified by the fabric softener
instructions.
• Caution - hot surface : Do not touch the
door light cover surface when the light is
switched on.1)
•
Hot surface: Do not touch the back
of the appliance while it is operating!
Child safety
• This appliance is designed to be operated
by adults.
• This machine is not intended for use by
young children or infirm persons without
supervision.
• Children often do not recognise the
hazards associated with electrical
appliances. Children should be supervised
to ensure that they do not play with the
appliance.
• The packaging components (e.g. plastic
film, polystyrene) can be dangerous to
children - danger of suffocation! Keep them
out of children’s reach.
• Keep all detergents in a safe place out of
children’s reach.
• Make sure that children or pets do not
climb into the drum.
1) Only dryers equipped with internal drum light.
4
Contents
Important safety information 2
For the installer
Product description
7
Technical data
23
Control Panel
8
8
8
8
8
8
9
9
9
9
Installation
23
23
24
24
26
27
29
1. PROGRAMME KNOB
2. HALF POWER
3. LONG ANTICREASE
4. ALARM
5. TIME
6. START / PAUSE BUTTON
7. FILTER LIGHT
8. DELAY START
9. DISPLAY
Before first use
Appliance positioning
Removing transport safety packaging
Fitting the vent hose
Changing door stop
Electrical connection
Special accessories
10
Sorting and preparing laundry 10
Sorting laundry
Laundry weights
10
10
Programme chart
11
Daily use
14
14
14
15
15
15
15
15
16
Switching machine on
Door opening and laundry loading
Selecting the programme
Selecting additional functions
Setting child lock
Starting the programme
Changing programme
Drying cycle complete / removing laundry
Cleaning and maintenance
Cleaning fluff filter
Cleaning the door
Cleaning the drum
Clean operating screen and housing
What to do if ...
Troubleshooting by yourself
Machine settings
ALARM SIGNAL permanent off
Guide to use the
instruction manual
17
17
17
18
18
The following symbols will be found in the text
to guide you throughout the instructions:
18
18
Safety instructions
20
20
Hints and tips
5
Water hardness
20
Environment
Environmental tips
20
21
Service
22
Environmental information
6
Product description
1
8
2
3
7
6
4
5
1
2
3
4
Control panel
Door
Fluff filter
Rating plate
5
6
7
8
7
Adjustable feet
Sideways vent outlets / back vent outlet
Ring nut
Lamp for inside light
Control Panel
9
1
2
3
4
5
8
7
6
1. PROGRAMME KNOB
4. ALARM
By operating the knob you can select the
proper drying program or turn the appliance
off.
When the drying cycle has finished, an
intermittent audible signal will sound. By
depressing button ALARM the acoustic signal
is switched off in the following cases:
• when selecting the programme
• when depressing the buttons
• when the programme selector dial is turned
to another position during the programme
or when you depress an option button
during the cycle
• at the end of the programme.
The corresponding light comes on.
2. HALF POWER
Pressing this button allows drying to be
performed at a lower temperature, for
delicate items. The corresponding pilot light
comes on. This option can also be used for
time controlled drying.
3. LONG ANTICREASE
A long anti-crease phase lengthen the anticrease phase (30 min.) at the end of the drying
additionally by 60 minutes. The drum rotates
at intervals during this phase. This keeps the
laundry loose and free of creases. Phase lasts
in total 90 minutes. The laundry can be
removed at any time during the anti-crease
phase.
When the option is active, the LONG
ANTICREASE light is on.
5. TIME
Use the Time button to select the programme
duration after setting the TIME programme.
You can select a programme duration from 20
min. to 3 hours in 10-minute steps.
1. Turn the programme selector to the TIME
programme.
8
2. Press the TIME button repeatedly until the
desired programme duration is shown in
the display, e.g.
for a
programme of 20 minutes.
If the programme duration is not selected, the
duration is automatically set to 10 mins.
3. To activate the delay timer, press the
START PAUSE button. The amount of
time remaining until the programme is set
to start is continuously displayed (e.g. 15h,
14h, 13h, … 30' etc).
9. DISPLAY
6. START / PAUSE
BUTTON
With the START PAUSE button you can start
or pause the drying program.
7. FILTER LIGHT
The warning light FILTER is on after every
drying cycle to remind you about filter
cleaning.
SYMBOL
DESCRIPTION
Time to end (time of time
programm, time of start delay)
8. DELAY START
Child lock
With the DELAY START button, you
can delay the start of a programme by
between 30 minutes (30') and a
maximum of 20 hours (20h).
Delay start
Drying phase
Cooling phase
Anticrease guard phase
1. Select the programme and additional
functions.
2. Press the DELAY START button as many
times as necessary until the required time
of the delay appears on the display, e.g.
H if the programme is to be started
in 12 hours.
Error, wrong selection
If the display is showing
H and
you press the button again, the time
delay will be cancelled. The display will
show 0 and then the duration of the
selected programme.
9
Before first use
a brief drying cycle (ca. 30 min.) with damp
cloths in the machine.
In order to remove any residues which may
have been produced during production, wipe
the dryer drum with a damp cloth or carry out
Sorting and preparing laundry
• Do not dry new, coloured textiles together
with light-coloured laundry items. Textile
colours may bleed.
• Do not dry cotton jersey and knitwear with
the EXTRA DRY programme. Items may
shrink!
Preparing laundry
• To avoid laundry becoming tangled: close
zips, button up duvet covers and tie loose
ties or ribbons (e.g. of aprons).
• Empty pockets. Remove metal items
(paper clips, safety pins, etc).
• Turn items with double-layered fabrics
inside out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost).
These fabrics will then dry better.
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in
COTTONS programme group.
– Mixtures and synthetics for programmes
in SYNTHETICS programme group.
• Sort by care label: The care labels mean:
Drying in the tumble dryer possible in
principle
Drying at normal temperature
Drying at reduced temperature (press
HALF POWER button!)
Drying in the tumble dryer not possible
Important! Do not place in the appliance
any wet laundry which is not specified on the
care label as being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for
tumble-drying.
Important! Do not overload the appliance.
Observe max. loading volume of 7 kg.
Laundry weights
Type of
laundry
Weight
Type of
laundry
Bathrobe
1200 g
Quilt cover
700 g
Napkin
100 g
Sheet
500 g
10
Weight
Type of
laundry
Weight
Pillow case
200 g
Tablecloth
250 g
Towelling
towel
200 g
Tea cloth
100 g
Night dress
200 g
Ladies' briefs
100 g
Type of
laundry
Weight
Man's work
shirt
600 g
Man's pyjamas
500 g
Blouse
100 g
Men's
underpants
100 g
Additional functions/
options
Application/properties
7 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START
Thorough drying of thick or
multi- layered fabrics, e.g.
terry towelling items,
bathrobes.
7 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START
Thorough drying of thick or
multi- layered fabrics, e.g.
terry towelling items,
bathrobes.
COTTONS
CUPBOARD DRY 1)
7 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START
Thorough drying of fabrics of
even thicknesses, e.g. terry
towelling items, knitwear,
towels.
COTTONS IRON
DRY 1)
7 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START
For thin fabrics which are
also to be ironed, e.g.
knitwear, cotton shirts.
Programmes
COTTONS EXTRA
DRY
COTTONS STORE
DRY
Care mark
max. load (weight when dry)
Programme chart
11
Application/properties
3 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START
Thorough drying of thick or
multi-layered fabrics, e.g.
pullovers, bedding, table
linen.
SYNTHETICS
CUPBOARD DRY 1)
3 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY
For thin fabrics which are not
ironed, e.g. easy care shirts,
table linen, baby clothes,
2)
socks, lingerie with bones or
wires.
SYNTHETICS IRON
DRY
3 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START
For thin fabrics which are
also to be ironed, e.g.
knitwear, cotton shirts.
DELICATE
2 kg
HALF POWERAutomatic),
LONG ANTICREASE ,
ALARM , DELAY START
Delicate cycle is a special
programme for synthetics or
mixed fabrics which do not
require ironing, and need to
be "Store dry" (e.g. curtains).
DUVET
3 kg
HALF POWER, LONG
ANTICREASE , ALARM ,
DELAY START
Bed linen (single and double
sheet, pillowcase,
bedspread, duvet cover).
SYNTHETICS
EXTRA DRY
Care mark
max. load (weight when dry)
Additional functions/
options
Programmes
12
2)
2)
EASY IRON
MIXED LOAD
HEAVY COTTON
20 MINUTE DRY
Care mark
max. load (weight when dry)
Programmes
Additional functions/
options
Application/properties
1 kg (or 5
shirts)
HALF POWERAutomatic) ,
LONG ANTICREASE ,
ALARM , DELAY START
Special programme with
anti-crease mechanism for
easy care textiles such shirts
and blouses; for minimum
ironing effort. The result
depends on the type and
quality of textiles. (The
loading volume corresponds
to approx. 5 to 7 shirts.)
Recommendation: Place
textiles in the dryer straight
after spinning. Once dried,
immediately remove textiles
and place on clothes hanger.
3 kg
HALF POWER 3) , LONG
ANTICREASE , ALARM ,
DELAY START
For drying cotton and
synthetic fabrics, uses low
temperature.
7 kg
HALF POWER, LONG
ANTICREASE , ALARM ,
DELAY START
For leisure clothing, such as
jeans, sweat-shirts, etc., of
different material
thicknesses (e.g. at the neck,
cuffs and seams).
HALF POWERAutomatic) ,
LONG ANTICREASE ,
ALARM , DELAY START
Special program with anticrease mechanism for easy
care fabrics such shirts and
blouses; for minimum
ironing effort. The result
depends on the type of fabric
and its finish. Place fabrics in
the dryer straight after
spinning. Once dried,
immediately remove fabrics
and place on a clothes
hanger
1kg or 5
shirts
13
TIME
Additional functions/
options
7 kg
HALF POWER , LONG
ANTICREASE , ALARM ,
DELAY START , TIME
Care mark
max. load (weight when dry)
Programmes
Application/properties
For further drying of
individual items of laundry.
1) In accordance with IEC61121
2) select HALF POWER option
3) Automatic
Daily use
Switching machine on
Turn the programme selector to any
programme. The machine has been switched
on.
Door opening and laundry
loading
1. Open loading door:
Push against the loading door (push point)
2. Load your laundry (do not force it in).
Caution! Do not jam laundry in
between the loading door and rubber
seal.
3. Close loading door securely. Lock must
audibly lock.
14
button 4-TIME
button 6-DELAY START
Selecting the programme
Setting child lock
The child lock can be set to prevent a
programme being accidentally started or a
programme in operation being accidentally
changed. The child lock function locks all
buttons and the programme knob. The child
lock can be activated or deactivated by
holding down the ALARM and TIME buttons
simultaneously for 5 seconds.
– Before programme is started:
Appliance cannot be used
– After programme is started:
Programme in operation cannot be
changed
Use the programme selector to set the
programme you require. The estimated time
to end of the programme appears in the LCD
in h:mm format (hours:minutes).
during the cycle time elapses by steps of one
minute; less than 1 hour the leading zeros are
not shown (ex. “59”, “5”, “0”);
The icon appears in the display to indicate
that the child safety device is activated.
The child safety device is not deactivated once
the programme comes to an end.
If you want to set a new programme, you must
first deactivate the child safety device.
Selecting additional
functions
Starting the programme
Press the START PAUSE button. The
programme is started.
The programme phase is shown in display by
appropriate icons. From left to the right, from
drying ,anticrease , to cooling .
You can choose from the additional functions:
7
6
Changing programme
To change a programme which has been
selected by mistake once the programme has
started, first turn the programme selector to
OFF position. The programme is cancelled.
1
2
3
4
5
button 1 -HALF POWER
button 2 -LONG ANTICREASE
button 3 -ALARM
15
1. Open door.
2. Remove laundry.
3. Remove filter after clothes has been
removed. Clean the filter.
The programme can no longer be
changed directly once the programme
has started. If nevertheless there is an
attempt to change the programme on
the programme knob or if an function
button (excluding the ALARM
button) is pressed, led above START/
PAUSE button starts flashing
temporarily in yellow. The drying
programme is not however affected by
this (laundry protection).
Warning! Before you replace the
filter, please check if there is anything
inside the filter seat.
4. Turn the programme selector to OFF .
Important! Clean the filter after each drying
cycle.
Drying cycle complete /
removing laundry
5. Close the door.
Once the drying cycle is complete, display
shows a blinking " 0 ", under anti-crease
and FILTER light appear dash. If the
ALARM button has been pressed, an
acoustic signal sounds intermittently for about
one minute.
The drying cycles are automatically
followed by an anti-crease phase
which lasts around 30 minutes. The
drum rotates at intervals during this
phase. This keeps the laundry loose
and free of creases. The laundry can be
removed at any time during the anticrease phase. (The laundry should be
taken out towards the end of the anticrease phase at the latest to prevent
creases from forming.) If LONG
ANTICREASE
function has
been selected, the anti-crease phase is
lengthened by 60 minutes.
16
Cleaning and maintenance
3.
Warning! The tumble dryer is not to
be used if industrial chemicals have
been used for cleaning!
Cleaning fluff filter
The filter collect all the fluff which accumulates
during drying. To ensure that the dryer works
perfectly, the fluff filter must be cleaned after
every drying cycle.
The warning light FILTER , is on to remind you
of this operation.
Caution! Never operate the dryer
without fluff filter or with damaged or
blocked fluff filter.
Open the filter pressing the button,
among two slots on fingers. Clean the
filter using damp hand or cloth. After a
period of time, a patina due to detergent
residue on laundry forms on the filters.
When this occurs, clean the filter with
warm water using a brush.
Close the filter and do not forget to put it
back.
1.
Warning! Before you replace the
filter, please check if there is anything
inside the filter seat.
4. The filter can be positioned only to one
side. If position is wrong, the filter
overhangs.
Open loading door and remove laundry.
2. Remove the filter which is built into the
lower part of the loading aperture.
If the filter will not snap into place, the
loading door cannot be closed.
Cleaning the door
Clean periodically the interior part of the door
to remove any fluff. Accurate cleaning ensures
correct drying.
17
Cleaning the drum
Clean operating screen
and housing
Caution! Do not use abrasives or
steel wool to clean the drum.
Caution! Do not use furniture
cleaners or aggressive cleaning agents
to clean the machine.
Use a damp cloth to wipe down the
operating screen and housing.
Lime in the water or cleaning agents
may form a barely visible lining on the
inside of the drum. The degree to
which the laundry has been dried is
then no longer detected reliably. The
laundry is damper than expected when
removed from the dryer.
Use a standard domestic cleaner (e.g.
vinegar-based cleaner) to wipe down
the inside of the drum and drum ribs.
What to do if ...
programme. Press the START PAUSE button
If the error is still displayed, please inform your
local Service Force Centre and quote the
error code.
Troubleshooting by
yourself
If, during operation, the error code E... plus
number or letter) appears on the LCD: Switch
the machine off and on again. Reset
Problem
Dryer does not work.
Drying results unsatisfactory.
Possible cause
Remedy
Mains plug is not plugged in or
fuse is not working correctly.
Plug in at mains socket. Check
fuse in fuse box (domestic
installation).
Loading door is open.
Close loading door.
Have you pressed theSTART
PAUSE button?
Press the START PAUSE button
again.
Wrong programme selected.
Select a different programme the
next time you dry (see
“Programme chart” chapter).
Filter clogged.
Clean filter.
Overloading of laundry.
Observe recommended loading
volumes.
Ventilation slots covered up.
Uncover ventilation slots.
18
Residue on inside surface of
drum or drum ribs.
Clean inside surface of drum and
drum ribs.
Conductance of water at
installation site differs from
standard setting of machine.
Re-programme standard setting
for degree of drying (see
‘Programming options’ chapter).
Loading door does not close.
Filter not in place.
Install filter into place.
When a button is pressed, Err
appears on the LCD.
Washing protection. After the
start of the programme, the
option can no longer be set.
Turn the programme knob to
OFF . Set the programme again.
Programme selector in OFF
position.
Turn programme selector to any
programme.
Defective light bulb.
Replace light bulb (see next
section).
Drum light does not work.
Displayed programme time
changes erratically or stays
unchanged for a long time.
Programme time is corrected
automatically depending on type Automatic process; this is not a
and volume of laundry and level machine fault.
of dampness.
Drying cycle ends shortly after
programme starts.
Not enough washing loaded or
washing loaded is too dry for
selected programme.
Filter clogged.
Drying cycle lasts an unusually
long time. Note: After around 5 Load volume too big.
hours the drying cycle ends
Laundry insufficiently spun.
automatically.
Changing the bulb for
interior lighting
Select time programme or higher
drying level (e.g. EXTRA DRY
instead of CUPBOARD DRY ).
Clean filter.
Reduce load volume.
Laundry must be adequately
spun.
Warning! Before replacing the bulb,
disconnect the mains plug.
1. Unscrew cover above the bulb (this can
be found directly behind the loading
aperture, at the top; refer to “Description
of machine” section.)
2. Replace defective bulb.
3. Screw cover back down.
Check the correct positioning of o-ring gasket
before screwing back the door light cover. Do
not operate the dryer when missing o-ring
gasket on door light cover.
Only use a special bulb which is designed
specially for dryers. The special bulb can be
obtained from your local Service Force
centre.
Warning! When the appliance is
switched on, the interior lighting
switches itself off after 4 minutes when
the door is open.
Warning! Do not use standard bulbs!
These develop too much heat and may
damage the machine!
19
Warning! For safety reasons, the
cover must be screwed down tightly.
If this is not done, the dryer must not
be operated.
Machine settings
could slightly influence the residual humidity
of the laundry at the end of the cycle. Your
dryer allows you to regulate the sensitivity of
the drying sensor based on conductivity values
of the water.
1. Turn the programme selector to any
programme.
2. Press simultaneously the ALARM and
START PAUSE buttons and hold down for
approx. 5 seconds. The current setting is
on the display:
– low conductivity
<300 micro S/cm,
– medium
conductivity 300-600 micro S/cm,
– high conductivity >600 micro S/
cm
3. Press the START PAUSE button
sequentially until you set desired level.
4. To memorize setting press simultaneously
the ALARM and START PAUSE buttons
or turn knob to OFF position
ALARM SIGNAL
permanent off
1. Turn the programme selector to any
programme.
2. Press simultaneously the LONG
ANTICREASE and ALARM buttons and
hold down for approx. 5 seconds.
3. The buzzer is by default always off. You
can use ALARM button to activate or
deactivate sound but machine does not
memorize your selection.
Water hardness
Water contains, a variable quantity of
limestone and mineral salts of which quantities
vary according to geographical locations thus
varying its conductivity values. Relevant
variations of the conductivity of the water
compared to those prefixed by the factory
Environment
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
20
your household waste disposal service or the
shop where you purchased the product.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste disposal
facilities.
Warning! When disposing of old
appliances, remove the mains cable
and dispose of together with the plug.
Remove the door hook and ensure it
is no longer lockable to prevent young
children being trapped inside.
Environmental tips
• In the dryer, laundry becomes fluffy and
soft. Fabric softeners are not therefore
needed when washing.
• Your dryer will function most economically
if you:
– always keep the ventilation slots on the
base of the dryer unobstructed;
– use the loading volumes specified in the
programme overview;
– clean the filter after each drying cycle;
– spin the laundry well before drying.
Example: Consumption data –
depending on spinning speed – for 7 kg
of laundry, dried using the COTTONS
(cotton) CUPBOARD DRY
programme.
– ensure the vent hose is not squashed or
kinked.
21
Pre-draining
Revolutions per minute
Drying cycle
Residual dampness
Energy in kWh
in litres
as a %
1000
4.20
60
3,9
1400
3.64
52
3,7
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating
instructions - see chapter What to do if….
Model
description:
PNC:
S No:
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No. is on rating plate stuck
to the product - to find it see chapter Product
description ))
– Type of fault
– Any error messages displayed by the
appliance
So that you have the necessary reference
numbers from your appliance at hand, we
recommend that you write them in here:
22
Technical data
Height x width x depth
85 x 60 x 58 cm
Drum volume
108 l
Depth with loading door open
109 cm
Height can be adjusted by
1.5 cm
Weight when empty
Loading volume (depends on
approx. 30kg
programme)1)
Voltage
max. 7 kg
230-240 V
Required fuse
13 A
Total power
2600 W
Energy efficiency class
C
Energy consumption (7 kg of cotton, predrained at 1000 rpm) 2)
3.9 kWh
Average annual energy consumption
263.1 kWh
Use
Domestic
Permissible ambient temperature
+ 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may deviate when
the machine is operated in domestic circumstances.
Energy consumption in kWh / average
drying time in min.
Programme
COTTONS CUPBOARD DRY 2)
3.9 / 95 (7 kg load pre-drained at 1000 rpm)
COTTONS IRON DRY 2)
SYNTHETICS CUPBOARD DRY
3.05 / 75 (7 kg load pre-drained at 1000 rpm)
2)
1.15 / 30 (3 kg load pre-drained at 1200 rpm)
1) Different loading volume data may be needed in some countries as a result of different measuring methods.
2) in accordance with EN 61121
Installation
Appliance positioning
Important! The appliance must be moved in
vertical position for transport.
• It is recommended that, for your
convenience, the machine is positioned
close to your washing machine.
23
• The tumble dryer must be installed in a
clean place, where dirt does not build up.
• Air must be able to circulate freely all round
the appliance. Do not obstruct the front
ventilation grille or the air intake grilles at
the back of the machine.
•Important! To keep vibration and noise to
Removing transport
safety packaging
Caution! Before use all parts of the
transport packaging must be removed.
a minimum when the dryer is in use, it should
be placed on a firm, level surface.
• Once in its permanent operating position,
check that the dryer is absolutely level with
the aid of a spirit level. If it is not, raise or
lower the feet until it is.
•Important! The feet must never be
removed. Do not restrict the floor clearance
through deeply carpets, strips of wood or
similar. This might cause heat built-up which
would interfere with the operation of the
appliance.
1. Open loading door.
2. Pull off adhesive strips from inside machine
on top of drum.
3. Remove foil hose and polystyrene padding
from the machine.
Important! The hot air emitted by the
tumble dryer can reach temperatures of up to
60°C. The appliance must therefore not be
installed on floors which are not resistant to
high temperatures.
When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
Warning! Should the appliance be
moved, it must be transported
vertically.
Fitting the vent hose
Warning! The appliance must not be
installed behind the lockable door, a
sliding door or a door with a hinge on
the opposite side to that of the
appliance.
To simplify the installation, there is a choice of
vent outlets: one at the back, the others in the
left and right-hand side. Connect the hose to
whichever is the more convenient by pulling
the ring nut (A) from the vent outlet at the
back, screwing it on to the hose and pushing
it firmly back into place. The unused vents
24
should now be sealed with the special snap
covers provided.
B
Once connected to the dryer, run the vent
hose to the desired outlet point, ensuring that
the run’s overall length is less than 2 m, and
that it contains no more than two bends. As
to the outlet itself, if you have decided on a
fixed wall/window grille, a good local
builder’s merchant should be able to supply
you with the necessary fittings and installation
advice.
A
A
Warning! It is important not to
connect the vent hose to, for example,
a cooker hood, or a chimney or flue
pipe designed to carry the exhaust
from a fuel burning appliance.
If the hose is too long and the room
temperature low, the moisture might
condense to water inside the hose. This is an
unavoidable natural phenomenon. To
prevent this water from Iying in the hose or
flowing back into the tumble dryer, it is
advisable to drill a small hole (via. 3 mm) in the
lowest point of the hose and to place a small
container below it. (See picture, point B).
25
Note that to avoid condensation problems, it
is essential that the dryer be fitted with the
flexible hose to carry its “exhaust” at least
beyond the kitchen units; preferable outside
the kitchen. In order to prevent the appliance
from overheating, it is important that the
steam exhaust is unobstructed. Therefore, in
case of a permanent hose fitted to an exterior
wall or ceiling, it must be ensured an exhaust
capacity of at least 150 m3/h. If the dryer is
fitted next to kitchen units, make sure that the
vent hose is not squashed. If the hose is
partially squashed, drying efficiency will be
reduced, resulting in longer drying times and
higher energy consumption. If the hose is
completely squashed, the safety cut-outs with
which the machine is fitted may operate.
When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
A
B
C
A
B
Changing door stop
Warning! Before changing the door
stop, disconnect the mains plug.
1.
2.
3.
Open loading door.
4.
Unscrew hinge A from the front of the
machine and take off the loading door.
Remove cover plates B . To do this,
insert a thin screwdriver into the slots as
shown in the illustration, press
downwards slightly and pry out the cover
plates.
Use an appropriate tool and exert
pressure to unfasten locking block C
from the snap-on fixture, take out and
re-insert on the other side having
rotated the block through 180°.
Caution! There is a little spring
under locking block C. To put all
parts together correctly, look at
the pictures:
26
7.
D
F
E
D
E
5.
6.
F
Unscrew cover plates D from the front
of the machine, rotate through 180°,
screw on the opposite side.
8. Unscrew door lock E , push down slightly
and remove from the front of the
machine.
9. Press snap-in button F in and down, press
cover down slightly and remove from
front of the machine.
10. Change door lock E over to the opposite
side, screw down the door interlock.
11. On the other side, insert cover F and
allow snap-in button to lock into place.
12. Insert loading door and hinges into
recesses on the front of the machine and
screw down.
Note regarding contact protection:
The machine is only secure for operations
again once all plastic parts have been inserted.
Unscrew hinge A from the loading door,
rotate through 180°, re-insert on the
opposite side and screw down.
Re-insert cover plates B on the opposite
site having first rotated them through
180°.
Electrical connection
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
27
If you fit your own plug, the colours of the
wires in the mains lead of your appliance may
not correspond with the markings identifying
the terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth)
wire to the terminal in the plug which is
marked with the letter "E" or the earth
symbol
or coloured green and yellow.
2. Connect the Blue (neutral) wire to the
terminal in the plug which is marked with
the letter "N" or coloured black.
3. Connect the Brown (live) wire to the
terminal in the plug which is marked with
the letter "L" or coloured red.
4. Upon completion there must be no cut,
or stray strands of wire present and the
cord clamp must be secure over the outer
sheath.
Warning! THIS APPLIANCE
MUST BE EARTHED.
Should the appliance power
supply cable need to be replaced,
this must be carried out by a
Service Force agent (see
chapter: Repairs - after sales
service).
The manufacturer declines any
liability should this safety
measure not be observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated on
the appliance’s rating plate. (See picture on
page 6).
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the fuse
in the plug supplied, a 13amp ASTA approved
BS 1363/A fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below. The
wires in the mains lead are coloured in
accordance with the following code:
• Green and Yellow - Earth
• Blue - Neutral
• Brown - Live
Warning! A cut off plug inserted
into a 13 amp socket is a serious
safety (shock) hazard.
Ensure that the cut off plug is
disposed of safely.
Warning! The plug must still be
accessible after the appliance
has been installed.
GREEN & YELLOW
Warning! The appliance should
not be connected to the
electrical supply by means of an
extension cable.
BROWN
BLUE
CORD CLAMP
28
A special stacking kit is available through your
dealer, to enable the mounting of the dyer on
top of a front loading washing machine with
cover’s depth between 48 and 60 cm. Read
carefully the instructions supplied with the kit.
Warning! The manufacturer
declines any responsibility for
damage or injury through failure
to comply with the above safety
precautions.
Should the appliance power
supply cable need to be replaced,
this must be carried out by our
Service Centre.
Warning! The power supply
cable must be accessible after
installing the machine.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Special accessories
Stacking kit
29
30
31
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
www. johnlewis.com
136909470-01-30012009

advertisement

Related manuals

Download PDF

advertisement