Zanussi | ZDEB47209W | User manual | ZANUSSI ZDEB47209W User Manual

User manual
Exhaust Dryer
ZDEB 47209W
Important safety information _ _ _ _ _ _ _ _ _
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Sorting and preparing laundry _ _ _ _ _ _ _ _
Programme chart _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
What to do if ... _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Machine settings _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Environment _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 14
Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 15
Subject to change without notice.
Important safety information
Important! In the interest of your safety
and to ensure the correct use, before
installing and first using the appliance,
read this user manual carefully, including
its hints and warnings. To avoid
unnecessary mistakes and accidents, it is
important to ensure that all people using
the appliance are thoroughly familiar with
its operation and safety features. Save
these instructions and make sure that
they remain with the appliance if it is
moved or sold, so that everyone using it
through its life will be properly informed
on appliance use and safety.
General safety
• It is dangerous to alter the specifications or
attempt to modify this product in any way.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Make sure that small pets do not climb into
the drum. To avoid this, please check into the
drum before using.
• Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp material can cause extensive damage and must
not be placed into the machine.
• In order to avoid danger of fires caused by
excessive drying, do not use appliance to dry
the following items: Cushions, quilts and the
like (these items accumulate heat).
Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted
with foam rubber pads should not be dried in
the tumble dryer.
Always unplug the appliance after use, clean
and maintenance.
Under no circumstances should you attempt
to repair the machine yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your
local Service Centre. Always insist on genuine spare parts.
Items that have been soiled with substances
such as cooking oil acetone, petrol, kerosene,
spot removers, turpentine, waxes and wax removers should be washed in hot water with
an extra amount of detergent before being
dried in the tumble dryer.
Danger of explosion: Never tumble dry
items that have been in contact with inflammable solvents (petrol, methylated spirits, dry
cleaning fluid and the like). As these substance are volatile, they could cause an explosion. Only tumble dry items washed with
Risk of fire: items that have been spotted or
soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in
the tumble dryer.
If you have washed your laundry with stain remover you must execute an extra rinse cycle
before loading your tumble dryer.
• Please make sure that no gas lighters or
matches have accidentally been left in pockets of garments to be loaded into appliance
Warning! Never stop a tumble dry before the end of the drying cycle unless
all items are quickly removed and spread
out so that the heat is dissipated. Risk of
• Risk of electric shock! Do not spray down
the appliance with jets of water.
• The final part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures that items will not be damaged.
• Ensure you have adequate ventilation in the
installation room to avoid the back flow of
gases into the room from appliances burning
other fuels, including open fires.
• This appliance is heavy. Care should be taken
when moving it.
• When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
• All packing and transit bolts must be removed
before use. Serious damage can occur to the
product and to property if this is not adhered
to. See relevant section in the user manual.
• Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.
• Care must be taken to ensure that the appliance does not stand on the electrical supply
• If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely.
• After having installed the appliance, check
that it is not pressing or standing on its electrical supply cable or/and inlet hose.
• If the tumble dryer is placed on top of a
washing machine, it is compulsory to use the
stacking kit (optional accessory).
• This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
• Only wash fabrics which are designed to be
machine dried. Follow the instructions on
each garment label.
• Do not dry unwashed items in the tumble dryer.
• Do not overload the appliance. See the relevant section in the user manual.
• Clothes which are dripping wet should not be
placed in the dryer.
• Garments which have been in contact with
volatile petroleum products should not be
machine dried. If volatile cleaning fluids are
used, care should be taken to ensure that the
fluid is removed from the garment before
placing in the machine.
• Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
• Never use the tumble dryer if the power supply cable, the control panel, the working surface or the base are damaged so that the inside of the tumble dryer is accessible.
• Fabric softeners, or similar products should
be used as specified by the fabric softener instructions.
• Caution - hot surface : Do not touch the
door light cover surface when the light is
switched on.1)
Hot surface: Do not touch the back of
the appliance while it is operating!
Child safety
• This machine is not intended for use by
young children or infirm persons without supervision.
• Children should be supervised to ensure that
they do not play with the appliance.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children danger of suffocation! Keep them out of children’s reach.
1) Only dryers equipped with internal drum light.
• Keep all detergents in a safe place out of
children’s reach.
• Make sure that children or pets do not climb
into the drum.
Product description
1 Control panel
2 Door
5 Adjustable feet
6 Sideways vent outlets / back vent outlet
3 Fluff filter
4 Rating plate
7 Ring nut
Control panel
1 Programme knob and OFF switch
2 Function buttons
3 Function status led
Drying light
End/Anti-crease light
Filter light
Before first use
In order to remove any residues which may have
been produced during production, wipe the dryer drum with a damp cloth or carry out a brief
drying cycle (ca. 30 min.) with damp cloths in
the machine.
Sorting and preparing laundry
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in COTTONS
programme group.
– Mixtures and synthetics for programmes in
SYNTHETICS programme group.
• Sorting by care label. The care labels mean:
• Empty pockets. Remove metal items (paper
clips, safety pins, etc).
• Turn items with double-layered fabrics inside
out (e.g. with cotton-lined anoraks, the cotton
layer should be outermost). These fabrics will
then dry better.
Important! Do not overload the appliance.
Observe max. loading volume of 7 kg.
Laundry weights
Drying in
the tumble
dryer possible in
Dry at
Dry at reduced
Drying in
the tumble dryer
not possible
Important! Do not place in the appliance any
wet laundry which is not specified on the care
label as being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for tumbledrying.
• Do not dry new, coloured textiles together
with light-coloured laundry items. Textile colours may bleed.
• Do not dry cotton jersey and knitwear with
the EXTRA programme. Items may shrink!
Preparing laundry
• To avoid laundry becoming tangled: close
zips, button up duvet covers and tie loose ties
or ribbons (e.g. of aprons).
Type of laundry
1200 g
100 g
Quilt cover
700 g
500 g
Pillow case
200 g
250 g
Towelling towel
200 g
Tea cloth
100 g
Night dress
200 g
Ladies' briefs
100 g
Man's work shirt
600 g
Man's work shirt
200 g
Man's pyjamas
500 g
100 g
Men's underpants
100 g
Additional functions/options
7 kg
Thorough drying of thick or
multi- layered fabrics, e.g. terry
towelling items, bathrobes.
7 kg
Thorough drying of thick or
multi- layered fabrics, e.g. terry
towelling items, bathrobes.
7 kg
Thorough drying of fabrics of
even thicknesses, e.g. terry
towelling items, knitwear, towels.
7 kg
For thin textiles which are still
to be ironed, e.g. knitted items,
cotton shirts.
DRY 1)
7 kg
For thin fabrics which are also
to be ironed, e.g. knitwear, cotton shirts.
3 kg
Thorough drying of thick or
multi-layered fabrics, e.g. pullovers, bedding, table linen.
3 kg
For thin fabrics which are not ironed, e.g. easy care shirts, table linen, baby clothes, socks,
lingerie with bones or wires.
3 kg
For thin fabrics which are also
to be ironed, e.g. knitwear, cotton shirts.
30 MIN
For further drying of individual
items of laundry or for small volumes of less than 1 kg.
Care mark
max. load (weight when dry)
Programme chart
Additional functions/options
1 kg
(or 5
Special programme with anticrease mechanism for easy
care textiles such shirts and
blouses; for minimum ironing
effort. The result depends on
the type and quality of textiles.
(The loading volume corresponds to approx. 5 to 7
shirts.) Recommendation: Place
textiles in the dryer straight after spinning. Once dried, immediately remove textiles and
place on clothes hanger.
3 kg
For drying cotton and synthetic
fabrics, uses low temperature.
2 kg
Baby cycle is a special programme for jumpers to be dried
“ready to wear”.
7 kg
For leisure clothing, such as
jeans, sweat-shirts, etc., of different material thicknesses (e.g.
at the neck, cuffs and seams).
Special programme, lasting
around 10 minutes, for refreshing or gently cleaning textiles
with commercially available dry
cleaning sets. (Only use those
products which are declared as
suitable for the drier by the
manufacturer; please observe
the manufacturer’s instructions
for use.)
7 kg
Care mark
max. load (weight when dry)
1) In accordance with IEC61121
2) Select DELICATE button
Daily use
Switching machine on
Turn the programme selector to any programme.
The machine switches on.
Door opening and
laundry loading
1. Door opening and
laundry loading
2. Load your laundry
(do not force it in).
Selecting the programme
Turn the programme
selector dial to the required programme.
The light START/
PAUSE starts to flash.
Selecting additional functions
You can choose from the additional functions:
button 1 - DELICATE
button 2 - ANTI-CREASE
button 3 - ALARME
button 4 - START/PAUSE
Caution! Do not
jam laundry in between the loading
door and rubber seal.
Close loading
door securely.
Lock must audibly
Pressing this button allows drying to be performed at a lower temperature, for delicate
items. The corresponding pilot light comes on.
This option can also be used for time controlled
A long anti-crease phase lengthen the anticrease phase (30 min.) at the end of the drying
additionally by 60 minutes. The drum rotates at
intervals during this phase. This keeps the laundry loose and free of creases. Phase lasts in total 90 minutes. The laundry can be removed at
any time during the anti-crease phase.
When the option is active, the ANTI-CREASE
light is on.
When the drying cycle has finished, an intermittent audible signal will sound. By depressing
button ALARM the acoustic signal is switched
off in the following cases:
• when selecting the programme
• when depressing the buttons
• when the programme selector dial is turned
to another position during the programme or
when you depress an option button during
the cycle
• at the end of the programme.
The corresponding light comes on.
Starting the programme
Press the START PAUSE button. The programme is started.
The programme phase is shown by appropriate
lights; light 7 - DRYING , light 6 - END .
Changing programme
To change a programme which has been selected by mistake once the programme has started,
first turn the programme selector to "O" (OFF)
position. The programme is cancelled.
around 30 minutes. The drum rotates at intervals during this phase. This keeps the laundry
loose and free of creases. The laundry can be
removed at any time during the anti-crease
phase. (The laundry should be taken out towards the end of the anti-crease phase at the
latest to prevent creases from forming.)
The programme can no longer be changed
directly once the programme has started. If
nevertheless there is an attempt to change the
programme on the programme knob or if an
function button (excluding the ALARME button2)) is pressed, led on the START/PAUSE
button starts flashing temporarily in red. The
drying programme is not however affected by
this (laundry protection).
Open door.
Remove laundry.
Remove filter after clothes has been removed. Clean the filter.
Drying cycle complete / removing laundry
Once the drying cycle is complete, the lights
END and light 5 - FILTER are on. If the buzzer is
active, an acoustic signal sounds intermittently
for about one minute.
Important! Clean the filter after each drying cycle.
Warning! Before You place the filter ,
please check it there is nothing inside the
filter seat.
Turn the programme selector to OFF .
Close the door.
The drying cycles are automatically followed by an anti-crease phase which lasts
Care and cleaning
Cleaning fluff filter
The filter collect all the fluff which accumulates
during drying. To ensure that the dryer works
perfectly, the fluff filter must be cleaned after every drying cycle.
The warning light FILTER , is on to remind you
this operation.
Caution! Never operate the dryer without
fluff filter or with damaged or blocked fluff
Open loading
door and remove laundry.
Remove the
filter which is
built into the
lower part of
the loading
Open the filter
pressing the
button, among
two slots on
fingers. Clean
the filter using
dump hand or
cloth. After a
period of time,
a patina due to detergent residue on laundry forms on the filters. When this occurs,
clean the filter with warm water using a
Close the filter and do not forget to put it
2) Only dryers with ALARME button
Warning! Before You place the filter,
please check it there is nothing inside the
filter seat.
The filter can be positioned only to one
side. If position is wrong, the filter overhangs.
If the filter will not snap into place, the
loading door cannot be closed.
Warning! You must DISCONNECT the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Cleaning the door
Clean periodically the interior part of the door to
remove any fluff. Accurate cleaning ensures correct drying.
To clean the drum
Caution! Do not use abrasive materials to
clean the drum. Use a soft detergent to
clean the inner side of the drum and the drum
Keep the inner surface of the drum and the
drum blades clean. The minerals from the
water or cleaning agents can collect on the inner surface of the drum. This cause that the
laundry is not sufficient dry.
Clean operating screen and housing
Caution! Do not use furniture cleaners or
aggressive cleaning agents to clean the
Use a damp cloth to wipe down the operating
screen and housing.
What to do if ...
Possible cause
Mains plug is not plugged in or
fuse is not working correctly.
Plug in at mains socket. Check
fuse in fuse box (domestic installation).
Loading door is open.
Close loading door.
Have you pressed the START
PAUSE button?
Press the START PAUSE button
Wrong programme selected.
Select a different programme the
next time you dry (see “Programme
chart” chapter).
Fluff filter clogged.
Clean fluff filter.
Overloading of laundry.
Observe recommended loading
Ventilation slots covered up.
Uncover ventilation slots.
Residue on inside surface of drum
or drum ribs.
Clean inside surface of drum and
drum ribs.
Conductance of water at installation site differs from standard setting of machine.1)
Re-programme standard setting
for degree of drying (see ‘Machine
settings’ chapter)1).
Loading door does not close.
Filter not in place2).
Install filter into place2).
Drying cycle ends shortly after programme starts.
Not enough washing loaded or
washing loaded is too dry for selected programme.
Select time programme or higher
drying level (e.g. EXTRA DRY instead of CUPBOARD DRY ).
Drying cycle lasts an unusually
long time. Note: After around 5
Filter clogged.
Clean filter.
Dryer does not work.
Drying results unsatisfactory.
Possible cause
hours the drying cycle ends automatically.
Load volume too big.
Reduce load volume.
Laundry insufficiently spun.
Laundry must be adequately spun.
1) Only dryers with conductance programming
2) Only dryers with removable filter
Machine settings
BUZZER permanent off
Water hardness
Water contains, a variable quantity of limestone and mineral
salts of which quantities vary according to geographical locations thus varying its conductivity values.
Relevant variations of the conductivity of the water compared
to those prefixed by the factory
could slightly influence the residual humidity of the laundry at
the end of the cycle. Your dryer
allows you to regulate the sensitivity of the drying sensor based
on conductivity values of the
Turn the programme selector to any programme.
Press simultaneously the DELICATE and ANTI-CREASE buttons
and hold down for approx. 5 seconds.
The buzzer is by default always off.
Turn the programme selector to any programme.
Press simultaneously the ANTI-CREASE and START/PAUSE buttons and hold down for approx. 5 seconds. Lights show the current
– END - low conductivity <300 micro S/cm
– DRYING - medium conductivity 300-600 micro S/cm
– DRYING and END - high conductivity >600 micro S/cm
Press the START/PAUSE button sequentially until you set desired
To memorize setting press simultaneously the the ANTI-CREASE and
START/PAUSE buttons or turn knob to OFF position
Technical data
Dimensions (mm)
Width / Height / Depth
85 x 60 x 58 cm
Max. depth
(with the appliance door open)
1090 mm
Max. width
(with the appliance door open)
950 mm
Electrical connection
230-240 V
50 Hz
13 A
Total power
2600 W
Drum volume
108 l
Weight of the appliance
32,5 kg
Laundry: max. weight
7 kg
Type of use
Ambient temperature
Energy consumption 1)
5 °C
35 °C
4,25 kWh
Annual energy consumption 2)
512 kWh
Energy efficiency class
Power consumption
Left-on mode
0,70 W
0,70 W
1) With reference to EN 61121. 7 kg of cotton and a spin speed at 1000 rpm.
2) Energy consumption per year in kWh, based on 160 drying cycles of the standard cotton programme at full
and partial load, and the consumption of the low-power modes. Actual energy consumption per cycle will
depend on how the appliance is used (REGULATION (EU) No 392/2012).
Appliance positioning
• It is recommended that, for your convenience,
the appliance is positioned close to your
washing machine.
• The tumble dryer must be installed in a clean
place, where dirt does not build up.
• Air must be able to circulate freely all round
the appliance. Do not obstruct the front ventilation grille or the air intake grilles at the back
of the appliance.
• To keep vibration and noise to a minimum
when the tumble dryer is in use, it should be
placed on a firm, level surface.
• Once in its permanent operating position,
check that the tumble dryer is absolutely level
with the aid of a spirit level. If it is not, raise or
lower the feet until it is.
• The feet must never be removed. Do not restrict the floor clearance through deep pile
carpets, strips of wood or similar. This might
cause heat built-up which would interfere
with the operation of the appliance.
• The hot air emitted by the tumble dryer can
reach temperatures of up to 60°C. The appliance must therefore not be installed on floors
which are not resistant to high temperatures.
• When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
• Should the appliance be moved, it must be
transported vertically.
• The appliance must not be installed behind a
lockable door, a sliding door a door with a
hinge on the opposite side to that of the appliance in such a way that a full opening of
the tumble dryer is restricted.
Removing transport safety packaging
Caution! Before use all parts of the
transport packaging must be removed.
1. Open loading door.
2. Pull off adhesive
strips from inside machine on top of drum.
3. Remove foil hose
and polystyrene padding from the machine.
Fitting the vent hose
To simplify the installation, there is a choice of
vent outlets: one at the back, the others in the
left and right-hand side. Connect the hose to
whichever is the more convenient by pulling the
ring nut (A) from the vent outlet at the back,
screwing it on to the hose and pushing it firmly
back into place. The unused vents should now
be sealed with the special snap covers provided.
If the hose is long and
the room temperature
low, the moisture might
condense to water
inside the hose. This is
an unavoidable natural
phenomenon. To
prevent this water from
Iying in the hose or
flowing back into the tumble dryer, it is
advisable to drill a small hole (via. 3 mm) in the
lowest point of the hose and to place a small
container below it. (See picture, point B).
Once connected to the dryer, run the vent hose
to the desired outlet point, ensuring that the
run’s overall length is less than 2 m, and that it
contains no more than two bends. As to the
outlet itself, if you have decided on a fixed wall/
window grille, a good local builder’s merchant
should be able to supply you with the necessary
fittings and installation advice.
It is important not to
connect the vent hose
to, for example, a
cooker hood, or a
chimney or flue pipe
designed to carry the
exhaust from a fuel
burning appliance.
Note that to avoid condensation problems, it is
essential that the dryer be fitted with the flexible
hose to carry its “exhaust” at least beyond the
kitchen units; preferable outside the kitchen. In
order to prevent the appliance from overheating,
it is important that the steam exhaust is unobstructed. Therefore, in case of a permanent
hose fitted to an exterior wall or ceiling, it must
be ensured an exhaust capacity of at least 150
m3/h. If the dryer is fitted next to kitchen units,
make sure that the vent hose is not squashed. If
the hose is partially squashed, drying efficiency
will be reduced, resulting in longer drying times
and higher energy consumption. If the hose is
completely squashed, the safety cut-outs with
which the machine is fitted may operate. When
operating the tumble dryer, the room temperature must not be lower than +5°C and higher
than +35°C, as it may affect the performance of
the appliance.
Electrical connection
Details on mains voltage, type of current and the
fuses required should be taken from the rating
plate. The rating plate is fitted near the loading
aperture (see “Product description” chapter).
Connect the machine to an earthed socket, in
accordance with current wiring regulations.
Warning! The manufacturer declines
any responsibility for damage or
injury through failure to comply with the
above safety precautions.
Should the appliance power supply cable
need to be replaced, this must be carried
out by an authorised service engineer or a
qualified electrician. .
The appliance is supplied with a 13 amp plug
fitted. In the event of having to change the fuse
in the plug supplied, a 13 amp ASTA approved
BS 1363/A fuse must be used.
Ensure that the cut off plug is disposed of
Warning! The plug must be accessible
after installing the machine.
Permanent connection
The wires in the mains lead are coloured in accordance with the following code:
1 Blue - Neutral
2 cord clamp
3 Brown - Live
4 Green and Yellow - Earth
The wire coloured green and yellow must be
connected to the terminal marked with the letter
«E» or by the earth symbol
or coloured green
and yellow.
The wire coloured blue must be connected to
the terminal «N» or coloured black.
The wire coloured brown must be connected to
the terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp
must be secure over the outer sheath.
Warning! A cut off plug inserted into a
13 amp socket is a serious safety
(shock) hazard.
In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply
(mains), with a minimum gap of 3 mm between
the switch contacts and of a type suitable for
the required load in compliance with the current
electrical regulations.
The switch must not break the yellow and green
earth cable at any point.
Door reversal
To make it easier to load or unload the laundry,
the door can be reversed. The door must only
be reversed by an authorised service engineer.
Please contact your local Service Force Centre.
The engineer will carry out the door reversal at
your cost.
Special accessories
Stacking kit
A special stacking kit is
available through your
dealer, to enable the
mounting of the dyer on
top of a front loading
washing machine with
cover’s depth between
48 and 60 cm. Read
carefully the instructions supplied with the kit.
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility
or contact your municipal office.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at the
community waste disposal facilities.
Warning! When disposing of old
appliances, remove the mains cable and
dispose of together with the plug. Remove the
door hook and ensure it is no longer lockable to
prevent young children being trapped inside.
Environmental tips
• In the dryer, laundry becomes fluffy and soft.
Fabric softeners are not therefore needed
when washing.
• Your dryer will function most economically if
– always keep the ventilation slots on the
base of the dryer unobstructed;
– use the loading volumes specified in the
programme overview;
– clean the filter after each drying cycle;
– spin the laundry well before drying.
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions (Chapter “What to do if…”).
If you were not able to remedy the problem
yourself, please contact your local service centre.
In order to be able to assist you quickly, we require the following information:
– Model description
– Product number (PNC)
– Serial number (S No.) (for numbers, see rating
– Type of fault
– Any error messages displayed by the appliance
So that you have the necessary reference numbers from your appliance at hand,
we recommend that you write them in here:
Model description:
S No.:
Download PDF