Aeg-Electrolux T57830 User manual

Aeg-Electrolux T57830 User manual
125985010 gb.qxp
2006-06-12
13:15
Page 1
LAVATHERM T57830
Condensation dryer
Sèche-linge à condensation
User Information
Notice d’utilisation
PERFEKT IN FORM UND FUNKTION
125985010 gb.qxp
2006-06-12
13:15
Page 2
Dear customer,
Please read these operating instructions carefully and pay particular
attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and
pass it on to any future owners.
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct
functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of the appliance.
Tips and information about economical and ecological use of the
machine are marked with the clover symbol.
Should any problems arise, this booklet provides instructions on how to
solve them by yourself; see section “Something not working?”.
If this information is not sufficient, please contact our nearest Service
centre (address and telephone numbers are indicated on the enclosed
leaflet).
Printed on recycled paper.
People who think ecologically, act accordingly...
2
125985010 gb.qxp
2006-06-12
13:15
Page 3
Contents
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmental tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Description of machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before the first drying cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sorting and preparing laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Overview of programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hints & Tips on Drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switching machine on / switching light on. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Opening loading door / loading laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting the programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting additional functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting time delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Starting the programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Changing programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Removing laundry or loading laundry when necessary . . . . . . . . . . . . . . . . . 14
Drying cycle complete / removing laundry. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cleaning lint filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cleaning the door seal.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Emptying the water reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning the drum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Clean operating screen and housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
What to do if…. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting by yourself. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Changing bulb for inside light. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Consumption values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation and connection instructions. . . . . . . . . . . . . . . . . . . . . . . . . 23
Installation safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Removing transport safety equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Permanent connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Door reversal instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Special accessories... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Guarantee Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Customer Service Centres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3
125985010 gb.qxp
2006-06-12
13:15
Page 4
Operating Instructions
Safety
Before first starting up
• Note the ”Installation and connection instructions”
• Before first starting up, check the machine for any damage incurred
during transport. Never connect up a damaged machine. If parts are
damaged, contact your supplier.
Intended use
• The dryer is intended for drying standard laundry in domestic applications.
• Conversions or modifications to the dryer are not permitted.
• The laundry must not contain flammable solvents (benzene, alcohol, stain remover, etc.). Risk of fire and/or explosion! Laundry which has come into contact with
such substances must be rinsed thoroughly by hand before drying.
• When using dry-cleaning sets: Only use those products which are declared as suitable for the dryer by the manufacturer.
• Do not place items of laundry in the dryer which contain foam rubber
or materials similar to rubber. Risk of fire!
• Do not place heavily worn laundry items in the dryer. Risk of fire!
• Do not place laundry items with loose fillings (e.g. cushions) in the
dryer. Risk of fire!
• Parts with rigid components (e.g. door mats) may cover the air slots.
Risk of fire! Do not place such items in the dryer.
• Do not overfill the dryer. Risk of fire! Observe max. loading volume of 7 kg.
• Ensure that explosive objects (e.g. cigarette lighters, spray cans, etc.) do
not enter the dryer with the laundry. Risk of fire and/or explosion!
• Risk of fire: items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in the tumble dryer.
• If you have washed your laundry with stain remover you must execute
an extra rinse cycle before loading your tumble dryer.
• Clean the micro-fine filter and fine strainer after each drying cycle.
• Do not use the machine if there are no lint filters or if these are damaged.
Risk of fire!
• Clean the heat exchanger regularly.
• With stacked washer and dryer: Do not place objects on the dryer. These
may fall off during operation.
• The covering bonnet of the bulb for the drum light must be screwed down tightly.
Child safety
• Keep packaging away from children. Risk of suffocation!
• Children can often not see the dangers associated with electric machines. Never leave unsupervised children near the dryer.
4
125985010 gb.qxp
2006-06-12
13:15
Page 5
• Ensure that children and small animals cannot climb into the dryer’s drum.
Risk of death! Keep the dryer door shut whenever it is not being used.
General safety
• Only specialists may undertake repairs on the dryer.
• Never start up the dryer if the mains cable is damaged or if the operating screen, operating plate or base area are damaged so that the inside of the machine is open and accessible.
• Switch off the dryer before all cleaning, care or maintenance work. Also disconnect the mains plug from the socket or – with permanent connections –
switch off the LS switch in the fuse box and/or fully unscrew the screwedin fuse.
• Disconnect the machine from the power supply during long pauses in operations.
• When removing from the socket, never pull the mains plug by the cable,
instead take a hold of the plug.
• Manifold plugs, couplings and extension cables must not be used. Risk
of fire from overheating!
• Do not spray down the dryer with jets of water. Risk of electric shock!
• Do not lean on the open door. The machine may tip over.
• Once the drying cycle has been interrupted, the laundry and drum may
be hot. Risk of burns! Take care when removing the laundry.
Disposal
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste disposal facilities.
Old appliance
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please
contact your local city office, your household waste disposal service or the
shop where you purchased the product.
Warning! Remove mains plug from socket when you have no further use for
the machine. Cut off mains cable and dispose of together with plug.
Destroy loading door lock. Children cannot then lock themselves in the
machine and put their lives at risk.
5
125985010 gb.qxp
2006-06-12
13:15
Page 6
Environmental tips
• In the dryer, laundry becomes fluffy and soft. Fabric softeners are not
therefore needed when washing.
• Your dryer will function most economically if you:
– always keep the ventilation slots on the base of the dryer
unobstructed;
– use the loading volumes specified in the programme overview;
– ensure you have good ventilation in the installation room;
– clean the micro-fine filter and fine strainer after each drying
cycle;
– spin the laundry well before drying. Example: Consumption data –
depending on spinning speed – for 7 kg of laundry, dried using
the COTTONS STORAGE DRY (KATOEN KASTDROOG) programme.
Pre-draining
Drying cycle
in litres
Energy
Costs
as a %
in kWh
in euros1)
3,6
60
3,95
0,59
1200
3,2
53
3,69
0,55
1400
3,0
50
3,39
0,50
1800
2,5
42
3,19
0,47
Revolutions
per minute
in liters
1000
1) Tariff: 0.15 Euro/kWh
6
125985010 gb.qxp
2006-06-12
13:15
Page 7
Description of machine
Operating screen
DELAY TIMER (STARTTIJDKEUZE) button
INTENSITY (RESTMulti-display
VOCHT) button
Display showing
level of dryness
Block of buttons
and displays
Programme selector
Programme progress display
Maintenance displays
– HEAT EXCHANGER (WARMTEWISSELAAR) (clean!)
– EMPTY WATER (RESERVOIR) (empty!)
– CLEAN FILTER (ZEEF) (clean lint filter!)
7
125985010 gb.qxp
2006-06-12
13:15
Page 8
Before the first drying cycle
In order to remove any residue which may have been produced during
production, wipe the dryer drum with a damp cloth or undertake a
brief drying cycle (30 MIN) with damp cloths.
Sorting and preparing laundry
Sorting laundry
• Sort by fabric type:
• Sort by fabric type:
– Cotton/linen for programmes in COTTONS programme group.
– Mixtures and synthetics for programmes in EASY CARES programme
group.
• Sorting by care label. The care labels mean:
Basic drying in Drying at
tumble dryer
normal
possible
temperature
Drying at reduced temperature
(press SPECIAL CARE button!)
Drying in tumble
dryer not possible
• Do not dry new, coloured textiles together with light-coloured laundry
items. Textile colours may bleed.
• Do not dry tricot or knitted items with the EXTRA DRY programme. Items
may become stuck!
• Wool and wool-like textiles can be dried using the WOOL (WOL) programme. Before the drying cycle spin the woollen textiles as well as possible (max. 1200 rpm). Only dry woollen textiles together which are similar or the same with repect to material, colour and weight. Please dry
heavy laundry items made of wool separately.
Preparing laundry
• To avoid laundry becoming tangled: Close zips, button up coverings and
tie loose bands or ribbons (e.g. of aprons).
• Empty pockets. Remove metallic items (paperclips, safety pins etc).
• Turn items with double-layered fabrics inside out (e.g. with cottonlined
anoraks, the cotton layer should be outermost). These fabrics will then
dry better.
8
125985010 gb.qxp
2006-06-12
13:15
Page 9
Overview of programmes
COTTONS
INTENSITY
(RESTVOCHT)
Application/properties
EXTRA DRY 7 kg
•
•
•
•
Drying thick or multi-layered
textiles, e.g. terry towelling
items, bathing costumes.
INTENSIVE
7 kg
DRY
•
•
•
•
Drying thick textiles, e.g. terry
towelling items, towels.
STORAGE
DRY
7 kg
•
•
•
•
Drying textiles of even thicknesses,
e.g. terry towelling items,
knitted items, towels.
DAMP
7 kg
•
•
•
•
For thin textiles which are still
to be ironed, e.g. knitted items,
cotton shirts.
HAND
IRON
7 kg
•
•
•
•
For normal thickness cotton or
linen laundry, e.g. bedding, table
linen.
Care
symbols
7 kg
•
•
•
•
For cotton or linen laundry
which are still to be put through
a machine, e.g. bedding, table
linen.
•
•
•
•
Drying thick or multi-layered
textiles, e.g. pullovers, bedding,
table linen.
2)
EXTRA DRY 3 kg
STORAGE
DRY
•
•
•
•
For thin textiles which are not
ironed, e.g. easy care shirts, table
linen, baby’s clothes, socks, corsetry.
2)
3 kg
3 kg
•
•
•
•
For thin textiles which are still
to be ironed, e.g. knitted items,
cotton shirts.
2)
DAMP
MACHINE
IRON
EASY CARES
AUDIBLE SIGNAL
(ZOEMER)
SENSITIVE1)
(BEHOEDZAAM)
Programme
max. loading volume
(weight when dry)
SPECIAL CARE1)
(LAGE TEMP.)
Additional
functions
1)SPECIAL CARE and SENSITIVE cannot both be selected at the same time.
2) Press the SPECIAL CARE button!
9
30 MIN
LEISURE
EASY IRON
1 kg
7 kg
1 kg
WOOL CARE 1 kg
REFRESH
1 kg
•
•
•
•
•
13:15
Page 10
•
•
•
•
•
-
•
-
-
-
INTENSITY
(RESTVOCHT)
Additional
functions
AUDIBLE SIGNAL
(ZOEMER)
SENSITIVE1)
(BEHOEDZAAM)
Programme
2006-06-12
max. loading volume
(weight when dry)
SPECIAL CARE1)
(LAGE TEMP.)
125985010 gb.qxp
Application/properties
-
For drying individual items of laundry
or for small volumes of less than 1kg.
•
Special programme for leisure clothing, such as jeans, sweat-shirts, etc., of
different material thicknesses (e.g. at
the cuffs and seams).
-
Special programme with anti-crease
mechanism for easy care textiles such
shirts and blouses; for minimum ironing
effort. The result depends on the type
and quality of textiles. (The loading volume
corresponds to approx. 5 to 7 shirts.)
Recommendation: Place textiles in the
dryer straight after spinning. Once
dried, immediately remove textiles and
place on clothes hanger.
-
Special programme for briefly treating
woollens with warm air after they have
been dried naturally, worn or stored for
long periods. Wool fibres are aligned
and the wool becomes soft and snugly.
Recommendation: Remove textiles
immediately after drying.
-
Special programme, lasting around 35
minutes, for refreshing or gently cleaning
textiles with commercially available dry
cleaning sets. (Only use those products
which are declared as suitable for the drier
by the manufacturer; please observe
the manufacturer’s instructions for use.)
1)SPECIAL CARE and SENSITIVE cannot both be selected at the same time.
2) Press the SPECIAL CARE button!
10
Care
symbols
2)
2)
125985010 gb.qxp
2006-06-12
13:15
Page 11
Hints & Tips on Drying
Before placing articles of laundry in your tumble dryer, check the care
labels to ensure they are recommended for tumble drying.
Here is a list of the approximate weight of some common laundry items.:
Sheet
700 to 1000 g
Pillowcase
100 to 200 g
Tablecloth
400 to 500 g
Table Napkin
50 to 100 g
Kitchen Towel
70 to 120 g
Linen Hand Towel
100 to 150 g
Hand Towel
150 to 250 g
Bath Towel
700 to 1000 g
Bathrobe
1000 to 1500 g
Shirt
200 to 300 g
Apron
150 to 200 g
• Always load well spun laundry. The higher the spin speed the lower
the electricity consumption and the shorter the drying time.
• DO NOT load dripping wet laundry into the dryer. Roll the article in
a towel or spin to remove excess water.
• Close poppers and zips and fasten any buttons.
• Sort the laundry. Separate synthetics from cotton/linens, and dry separately.
• Remove the laundry immediately after the programme has finished.
• Use a fabric conditioning sheet to reduce static. We recommend the
sheet is pinned to an article of laundry (using a safety pin).
• Mix the load i.e. large and small articles.
• When drying large items such as sheets, we recommend you periodically stop the dryer to redistribute the load.
DO NOT use the tumble dryer to dry the following:
• Articles contaminated with inflammable substances e.g. petrol, cleaning
solvents, cooking oil, fats or hair lacquer.
• Woollen and synthetic/wool mixtures unless the item is labelled as
suitable for tumble drying.
• Very delicate articles such as silk.
• Very large and bulky items such as duvets or sleeping bags.
11
125985010 gb.qxp
2006-06-12
13:15
Page 12
Drying
Switching machine on / switching light on
Turn the programme selector to any programme or turn it to LIGHT. The machine has been switched on. When the loading door is opened, the drum is illuminated.
Opening loading door / loading laundry
1.Open loading door:
Use force to push against the loading door (push point
)
2. Load your laundry (do not force it in).
Caution! Do not jam laundry in between the loading door and rubber seal.
3. Close loading door securely. Lock must audibly lock.
Selecting the programme
Use the programme selector to set
the programme you require.
Selecting additional functions
INTENSITY
Precise setting of humidity content
of laundry. Laundry becomes dryer
from + to +++.
1. Press the INTENSITY button as
many times as necessary until the
small light at the level of residual
dampness required is illuminated.
If required, press the AUDIBLE
SIGNAL (Zoemer), SPECIAL CARE (Lage
Temp.) or SENSITIVE (Behoedzaam) buttons.
12
125985010 gb.qxp
2006-06-12
13:16
Page 13
AUDIBLE SIGNAL
When the drying cycle has finished, an intermittent audible signal will sound.
SPECIAL CARE
For especially gentle drying of sensitive fabrics with the
care label
and for temperature-sensitive textiles (e.g. acrylic, viscose). Programme
is executed with reduced heat.
SPECIAL CARE is only suitable for use with loads of up to 3 kg!
SENSITIVE
For gentle drying of frequently-worn textiles. Programme starts on full heat
setting, which is then reduced towards the end of the programme to ensure gentle care of laundry.
SPECIAL CARE and SENSITIVE cannot be selected together.
Setting time delay
With the DELAY TIMER button, you can delay the start of a programme by
between 30 minutes (30' and a maximum of 23 hours (23h).
1. Select the programme
2. Press the DELAY TIMER button as many times as necessary until the required start delay appears on the multi display, e.g. 12h if the programme is to
be started in 12 hours. The DELAY TIMER display is illuminated.
If 23h is displayed and you press the button again, the time delay will be cancelled. The display will show 0' and then the duration of the selected programme.
3. To activate the delay timer, press the START/PAUSE button. The amount of
time remaining until the programme is set to start is continuously displayed
(e.g. 12h, 11h, 10h, 30' etc).
Until the start of the programme the drum is moved at longish intervals to
loosen the laundry
Starting the programme
Press the START/PAUSE button. The programme is started.
The programme progress display and the display showing the level of dryness show drying progress.
Changing programme
To change a programme which has been selected by mistake once the programme has
started, first turn the programme selector to OFF and then reset the programme.
The programme can no longer be changed directly once the programme has started. If
nevertheless there is an attempt to change the programme on the programme knob,
the programme progress display and the maintenance indicators flash. If an option
button (excluding the AUDIBLE SIGNAL button) is pressed, the corresponding indicator
flashes several times. The drying programme is not however affected by this
(laundry protection).
13
125985010 gb.qxp
2006-06-12
13:16
Page 14
Removing laundry or loading laundry when necessary
1. Open loading door
Warning! Laundry and drum can become hot. Risk of burns!
2. Load or remove laundry items.
3. Close loading securely. Lock must audibly lock.
4. Press the START/PAUSE button to continue the drying cycle.
Drying cycle complete / removing laundry
Once the drying cycle is complete, the END and CREASE GUARD displays light up. If the AUDIBLE SIGNAL button has been pressed, an
audible signal sounds intermittently.
The drying cycle is automatically followed by a crease guard phase
which lasts around 30 minutes. The drum rotates in intervals during this
phase. The laundry thereby remains relaxed and free of creases. The
laundry can be removed at any time during the crease guard phase. (The
laundry should be taken out towards the end of the crease guard phase
at the latest to prevent creases from forming.)
1. Open loading door
2. Before removing the laundry, remove lint from the micro-fine filer. It
is best to use a damp hand for this purpose (refer to “Cleaning and
maintenance” section).
3. Remove laundry.
4. Turn the programme selector to OFF.
Important! After each drying cycle
– clean the micro-fine filter and fine strainer,
– drain the condensate tank
(refer to the “Cleaning and maintenance” section).
5. Close loading door.
14
125985010 gb.qxp
2006-06-12
13:16
Page 15
Cleaning and maintenance
Cleaning fluff filter
To ensure that the dryer works perfectly, the
fluff
filters
(micro-fine
filter
and fine strainer) must be cleaned after every
drying cycle.
Caution! Never operate the dryer without
fluff filters or with damaged or blocked fluff
filters.
1. Open loading door
2. Use a damp hand to clean the microfine filter, which is built into
the lower part of the loading aperture.
3. Push down unlock button on large mesh
filter. Large mesh filter jumps up.
4. Take out fine strainer.
5. Remove fluff from fine strainer.
It is best to use a damp hand for this
purpose.
15
125985010 gb.qxp
2006-06-12
13:16
Page 16
Clean the entire filter area
The strainer area does not have to be cleaned after every drying cycle,
but should be checked regularly and cleaned of fluff if necessary.
6. To do this, grip the top of the large mesh filter and pull it forwards until it
comes loose from the two brackets.
7. Remove fluff from the entire filter
area. It is best to use a vacuum
cleaner for this purpose.
8. Press both journals of the large
mesh filter into the brackets on
the loading door until they snap
into place.
9. Re-insert fine strainer .
10. Press against the large mesh filter
until it locks into the interlock.
If the fine strainer is not fitted, the large
mesh filter will not snap into place and
the loading door cannot be closed.
Cleaning the door seal
Wipe the door seal with a damp cloth immediately after the drying cycle
has finished.
Emptying the water reservoir
Empty condensate tank after every drying cycle.
If the condensate tank is full, an active programme will break off automatically and the EMPTY WATER display will light up. In order to continue the
programme, the condensate tank must first be emptied.
Warning! The condensate is not suitable for drinking or for preparing foodstuffs.
1.Take out drawer containing
condensed water container
completely (1) and pull up the
condensed water container’s
drainage pipe as far as it will go (2).
16
125985010 gb.qxp
2006-06-12
13:16
Page 17
2.Pour condensed water out into
a basin or similar receptacle.
3.Slide outlet connections in and
refit condensate tank. If the
programme has been interrupted as a result of the condensate tank being full: Press the
START/PAUSE button to continue the drying cycle.
The water reservoir has a volume of approx. 4 litres. This is sufficient for around 6 kg of
laundry which has previously been spun at 800 revolutions/ minute.
The condensate can be used as distilled water, e.g. for steam ironing. However
first filter the condensate (e.g. with a coffee filter) to remove any residue
and small pieces of fluff.
Cleaning heat exchanger
If the HEAT EXCHANGER display is illuminated, the heat exchanger needs to
be cleaned.
Caution! Operating when the heat exchanger is clogged with lint can
damage the dryer. This also increases energy consumption.
1. Open loading door
2. Open base door. To do this, press the
release button on the bottom of the
loading opening and open the door to
the left.
3. Remove lint from the inside of the door
and the heat exchange chamber. Wipe
the door seal with a damp cloth.
4. Turn both lock washers inwards.
5. Use the handle to pull the heat exchanger out of the base and carry it horizontally to prevent any remaining water from
spilling.
6. To empty the heat exchanger, hold
vertically over a washing-up bowl.
17
125985010 gb.qxp
2006-06-12
13:16
Page 18
Caution! Do not use sharp objects to
clean. The heat exchanger could
develop leaks.
7. Clean heat exchanger.
It is best to use a brush or to rinse
thoroughly with a shower head.
8. Replace heat exchanger and lock into
place (turn both lock washers
outwards until they snap into place).
9. Close base door.
The dryer will not operate if the HEAT EXCHANGER indicator is still lit.
Caution! Never operate the dryer without the heat exchanger.
Cleaning the drum
Caution! Do not use abrasives or steel wool to clean the drum.
Lime in the water or cleaning agents may form a barely visible lining on the
inside of the drum. The degree to which the laundry has been dried is then
no longer detected reliably. The laundry is damper than expected when
removed from the dryer. Use a standard domestic cleaner (e.g. vinegar-based
cleaner) to wipe down the inside of the drum and drum ribs.
Clean operating screen and housing
Caution! Do not use furniture cleaners or aggressive cleaning agents to
clean the machine.
Use a damp cloth to wipe down the operating screen and housing.
18
125985010 gb.qxp
2006-06-12
13:16
Page 19
What to do if …
Troubleshooting by yourself
If, during operation, the error code (E plus number or letter) appears on
the multi-display: Switch the machine off and on again. Reset programme. Press the START/PAUSE button.If the error is still displayed, please
inform your local Service Force Centre and quote the error code.
Problem
Drying cycle lasts an
unusually long time.
Note:
After around 5 hours
the drying cycle ends
automatically (see
„Drying cycle complete“).
Drying cycle ends
shortly after programme
starts. END display illuminated.
Dryer does not work.
Possible cause
Remedy
Lint filter clogged.
Clean lint filter.
Heat exchanger clogged
with lint.
Clean heat exchanger.
SPECIAL CARE
button pressed and load
volume too big.
SPECIAL CARE is only suitable for use with
loads of up to 3 kg!
Load volume too big.
Reduce load volume.
Laundry insufficiently predrained.
Laundry must be adequately
predrained.
Select time programme or
Not enough washing loaded
higher drying level (e.g.
or washing loaded is too
INTENSIVE DRY instead of
dry for selected programme.
STORAGE DRY).
Mains plug is not plugged
in or fuse is not working
correctly.
Plug in at mains socket.
Check fuse in fuse box
(domestic installation).
Loading door is open.
Close loading door.
Have you pressed the
START/ PAUSE button?
Press the START/PAUSE
button again.
19
125985010 gb.qxp
2006-06-12
13:16
Problem
Page 20
Possible cause
Remedy
Select a different programme the next time you dry
Wrong programme selected.
(see “Overview of programmes” section).
Drying results
unsatisfactory.
Lint filter clogged.
Clean lint filter.
Heat exchanger clogged
with lint.
Clean heat exchanger.
Overloading of laundry.
Ventilation slots in base
area covered up.
Observe recommended loading volumes.
Uncover ventilation slots in
base area.
Residue on inside surface of Clean inside surface of
drum or drum ribs.
drum and drum ribs.
Make an adjustment using
the INTENSITY function (see
chapter ”Drying, Selecting
additional functions”).
Mains plug disconnected.
Loading door does not
open with DOOR button.
Loading door does not
close.
When pressing a button,
the corresponding
button flashes several
times.
Drum light does not
work.
20
Plug in at mains socket.
Set programme. Loading
Programme selector in OFF door can be opened at any
time by exerting pressure on
position.
the door.
Fine strainer not in place
Install fine strainer and/or
and/or large mesh filter not snap large mesh filter into
locked in place.
place.
Washing protection. After
Turn the programme knob
the start of the programme,
to OFF Set the programme
the option can no longer be
again.
set.
Programme selector in OFF
position.
Turn programme selector to
LIGHT or to any programme.
Defective light bulb.
Replace light bulb (see next
section).
PROGRAMME TIME display
changes erratically or stays
unchanged for a long
time.
Programme time is corrected
automatically depending on Automatic process; this is
type and volume of laundry not a machine fault.
and level of dampness.
Programme inactive,
EMPTY WATER display
illuminated.
Condensate tank is full.
Empty condensate tank,
then start programme with
START/PAUSE button.
125985010 gb.qxp
2006-06-12
13:16
Page 21
Changing bulb for inside light
Only use a special bulb which is designed specially for dryers. The special bulb
is available from the after-sales service, ET-Nr. 112 552 000-5.
Warning! Do not use standard bulbs! These develop too much heat andmay
damage the machine!
Warning! Before replacing the bulb, disconnect the mains plug; with a
permanent connection: fully unscrew or deactivate the fuse.
1. Unscrew covering bonnet from above bulb (this can be found directly behind
the loading aperture, at the top; refer to “Description of machine” section.)
2. Replace defective bulb.
3. Screw covering bonnet back down.
Warning! For reasons associated with safety, the covering bonnet must be
screwed down tightly. If this is not done, the dryer must not be operated.
Programming options
Objective
Permanently programme
in the audible signal
which reminds you that
the programme is complete.
Adjust “level of dryness”
detection:
If the laundry is slightly
drier or slightly damper at
the end of the programme
than with the standard
setting.
Implementation
1. Turn the programme selector to any programme.
2. Press the AUDIBLE SIGNAL button and hold down for
approx. 5 seconds.
A brief signal sounds several times. The AUDIBLE SIGNAL
display flashes several times.
The setting is permanently programmed.
The setting is cancelled as described under 1 and 2.
1. Turn the programme selector to any programme.
2. Press the AUDIBLE SIGNAL and SENSITIVE buttons at the
same time and hold down for approx. 5 seconds. The current setting appears on the multi-display:
– C0: Setting for drier laundry
– C1: Standard setting
– C2: Setting for damper laundry
3. Press the START/PAUSE button until the setting required
appears on the multi-display.
4. Turn the programme selector to OFF.
The setting is permanently programmed.
1. Turn the programme selector to any programme.
To deactivate the EMPTY 2. Press the DOOR and SPECIAL CARE buttons at the same
time and hold down for approx. 5 seconds. The multidisplay
WATER display when
briefly displays ”0”
using an external drain
The EMPTY WATER display is permanently deactivated. The
for the condensed water.
setting is cancelled as described under 1 and 2; the multidisplay however briefly displays ”1” (rather than ”0”).
21
125985010 gb.qxp
2006-06-12
13:16
Page 22
Technical data
This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth
85 x 60 x 60 cm
Depth with loading door open
109 cm
Height can be adjusted by
1,5 cm
Weight when empty
approx. 42 kg
Loading volume (depends on programme) 1)
max. 7 kg
Energy consumption in accordance with IEC 1121 s. e.
(7 kg of cotton, pre-drained at 1000 rpm, COTTONS
STORAGE DRY (KATOEN KASTDROOG) programme)
3,95 kWh
Use
Domestic
Use
+ 5°C à + 35°C
1) Different loading volume data may be needed in some countries as a result of different
measuring methods.
Consumption values
The consumption values have been established under standard conditions.
They may deviate when the machine is operated in domestic circumstances.
Programme
COTTONS STORAGE DRY 1)
7
3,95
COTTONS HAND IRON 1)
7
3,05
EASY CARES STORAGE DRY 2)
3
1,45
1) pre-drained at 1000 rpm
2) pre-drained at 1200 rpm
22
Loading volume Energy consumption
in kg
in kWh
125985010 gb.qxp
2006-06-12
13:16
Page 23
Installation and connection instructions
Installation safety instructions
• Before first starting up, all parts of the transport safety equipment must be
removed. The machine may otherwise be damaged.
• Before starting up for the first time, ensure that the nominal voltage and type of current specified on the machine type plate match the nominal voltage and type of current at the installation site. The electrical fuses required can also be found on the type plate.
• Always connect the plug into a protection contact socket which has been
installed as specified.
• With permanent connections: A permanent connection may only be established by an authorised specialist electrician.
• Do not install machine in rooms at risk of frost.
• Ensure that the door of the machine cannot be blocked by interior doors of
the house or the doors of other appliances.
• Do not install on carpets with high piles. Air circulation will be hindered at
the ventilation slots.
• Ensure that the machine is not placed on its mains cable.
• Install the machine horizontally.
Removing transport safety equipment
Caution! Before first starting up,
all parts of the transport safety
equipment must be removed.
1.Open loading door
2. Pull off adhesive strips from inside
machine on top of drum.
3. Remove foil hose and polystyrene
padding from the machine.
23
125985010 gb.qxp
2006-06-12
13:16
Page 24
Electrical connection
Any electrical work required to install this appliance should be carried out by a
qualified electrician or competent person.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should this safety measure not be observed.
Should the appliance power supply cable need to be replaced, this must be
carried out by our Service Centre.
Before switching on, make sure the electricity supply voltage is the same as that
indicated on the appliance’s rating plate. (See picture on page 7).
The power supply cable must be accessible after installing the machine.
Door reversal instructions
Warning! The door stop may only be changed by a specialist. If
necessary,please contact our after-sales service or your specialist dealer.
Warning! Before changing the door stop, disconnect the mains plug;
with a permanent connection: fully unscrew or deactivate the fuse.
1. Open loading door
.
2. Unscrew hinge A from the front ofthe
machine and take off the loading door.
3. Remove cover plates B and C. To do
this, insert a thin screwdriver into the
slots as shown in the illustration, press
downwards slightly and pry out the
cover plates.
4. Use an appropriate tool and exert pressure to unfasten locking block D from
the snap-on fixture, take out and reinsert on the other side, having rotated the
block through 180°.
5. Unscrew hinge A from the loading door,
rotate through 180°, reinsert on the
opposite side and screw down.
24
125985010 gb.qxp
2006-06-12
13:16
Page 25
6. Reinsert cover plates B and C on the
opposite site having first rotated them
through 180°.
7. Unscrew cover plates E from the front of
the machine, rotate through 180, screw
on the opposite side.
8. Unscrew door lock F, push down slightly and
remove from the front of the machine.
9. Press snap-in button G in and down,
press cover down slightly and remove
from front of the machine.
10. Transfer door lock F to the oppositeside and screw down.
11. Fix cover G on to the other side and allow the
snap-in button to lock in place.
12. Insert loading door and hinges into
recesses on the front of the machine and screw down.
Special accessories
The following special accessories are available from your Service Force Centre or your specialist dealer:
Intermediate installation kits for stacked washer and dryer:
These intermediate installation kits can be used to arrange the dryer and
an automatic AEG-Electrolux washing machine (60cm wide, front loading) as a space-saving washer/dryer stack. The automatic washing
machine is at the bottom and the dryer is at the top.
Two versions can be supplied:
– without stacker plate
916.018 902
– with extractable stacker plate
916.018 903
Installation kit for external condensate drain
Installation kit (125 122 510) for direct draining of condensate into a
basin, siphon, gully, etc. The condensate tank then no longer has to be
drained, it must however remain in its intended position in the machine. Refer to the “Programme options” section for how to deactivate the
EMPTY WATER display. Max. displacement height: 1m from the base of
the dryer; max. displacement length: 3m.
25
125985010 gb.qxp
2006-06-12
13:16
Page 26
Guarantee Conditions
Belgium
DECLARATION OF GUARANTEE TERMS.
Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services
department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result.
This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil
Code. The statutory rights that the consumer has under this legislation are not affected by this declaration of guarantee terms. This declaration does not affect the vendor's statutory warranty to the end user. The appliance is guaranteed within the context of and in adherence with the following terms:
1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of
charge any defect that occurs within 24 months from the date the appliance is delivered
to the first end user. These guarantee terms do not apply in the event of use for professional or equivalent purposes.
2. Performing the guarantee means that the appliance is returned to the condition it was in
before the defect occurred. Defective parts are replaced or repaired. Parts replaced free of
charge become our property.
3. So as to avoid more severe damage, the defect must be brought to our attention immediately.
4. Applying the guarantee is subject to the consumer providing proof of purchase showing
the purchase and/or delivery date.
5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous
ceramic), synthetic materials and rubber, is the result of inappropriate use.
6. The guarantee cannot be called on for minor faults that do not affect the value or the
overall reliability of the appliance.
7. The statutory warranty does not apply when defects are caused by:
• a chemical or electrochemical reaction caused by water,
• abnormal environmental conditions in general,
• unsuitable operating conditions,
• contact with harsh substances.
8. The guarantee does not apply to defects due to transport which have occurred outside of
our responsibility. Nor will the guarantee cover those caused by inadequate installation or
assembly, lack of maintenance or failure to respect the assembly instructions or directions
for use.
9. Defects that result from repairs or measures carried out by people who are not qualified
or expert or defects that result from the addition of non-original accessories or spare
parts are not covered by the guarantee.
10. Appliances that are easy to transport may be delivered or sent to the consumer services
department. Home repairs are only anticipated for bulky appliances or built-in appliances.
11. If the appliances are built-in, built-under, fixed or suspended in such a way that removing and replacing them in the place where they are fitted takes more than half an hour,
the costs that result therefrom will be charged for. Connected damage caused by these
removal and replacement operations will be the responsibility of the user.
12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or
26
125985010 gb.qxp
2006-06-12
13:16
Page 27
if the repair costs are considered disproportionate, in agreement with the consumer, the
defective appliance may be replaced with another appliance of the same value. In this
event, we reserve the right to ask for a financial contribution calculated according to the
length of time it has been used.
13. A repair under guarantee does not mean that the normal guarantee period will be extended nor that a new guarantee period begins.
14.We give a twelve month guarantee for repairs, limited to the same defect.
15. Except in the event where liability is legally imposed, this declaration of guarantee terms
excludes any compensation for damage outside the appliance for which the consumer
wishes to assert his rights. In the event of legally admitted liability, compensation will not
exceed the purchase price paid for the appliance.
These guarantee terms are only valid for appliances purchased and used in Belgium. For
exported appliances, the user must first make sure that they satisfy the technical conditions (e.g.: voltage, frequency, installation instructions, type of gas, etc.) for the country
concerned and that they can withstand the local climatic and environmental conditions.
For appliances purchased abroad, the user must first ensure that they meet the qualifications required in Belgium. Non-essential or requested adjustments are not covered by the
guarantee and are not possible in all cases. Our consumer services department is always at
your disposal, even after the guarantee period has expired.
Address for our consumer services department:
ELECTROLUX HOME PRODUCTS BELGIUM
Bergensesteenweg, 719 - 1502 LEMBEEK
Tel.: 02.363.04.44
Customer Service Centres
Belgium
Electrolux Home Products Belgium
ELECTROLUX SERVICE
Bergensesteenweg 719
1502 Lembeek
E-mail:
[email protected]
Consumer services
Tel.
02/363.04.44
Fax.:
02/363.04.00
02/363.04.60
27
125985010 gb.qxp
2006-06-12
13:16
Page 28
Service
In the event of technical faults, please first check whether you can remedy the
problem yourself with the help of the operating instructions (section “What to
do if…”).
If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners.
In order to be able to assist you
quickly, we require the following
information:
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers, see rating plate)
– Type of fault
– Any error messages displayed by the appliance
So that you have the necessary reference numbers from your appliance at
hand, we recommend that you write them in here:
28
Model description:
.....................................
PNC:
.....................................
S No.:
.....................................
125985010 gb.qxp
2006-06-12
13:16
Page 29
29
125985010 gb.qxp
30
2006-06-12
13:16
Page 30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement