Electrolux E36WV60PPS Owners manual

Electrolux E36WV60PPS Owners manual
Installation, Use & Care Guide
30”(76.2 cm) and 36”(91.4 cm) Range Hood
Guide d’installation, utilisation
et d’entretien
30”(76.2 cm) et 36”(91.4 cm) Hotte de la Cuisiniere
Guia de Instalación, Uso y Cuidado
Campana de cocina de 30”(76.2 cm) y 36”(91.4 cm)
E30WV60PPS + E36WV60PPS
316902932
October 2013
LI314A
2
Finding Information
Please read and save this guide
Thank you for choosing Electrolux, the new premium brand in home appliances. This Use & Care Guide is
part of our commitment to customer satisfaction and product quality throughout the service life of your new
appliance.
We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you,
please use this page to record important product information.
Keep a record for quick reference
Purchase date
Model number
NOTE
Registering your product with Electrolux enhances
our ability to serve you. You can register online at
www.electroluxappliances.com by dropping your
Product Registration Card in the mail.
Serial number (see picture for location)
Questions?
For toll-free telephone support in the U.S. and Canada:
1-877-4 ELECTROLUX (1-877-435-3287)
For online support and Internet production information visit http:// www.electroluxappliances.com
Table of contents
Important Safety Instructions ................................3
List of materials.........................................................4
Electrical requirements ...........................................4
Location requirements . ..........................................6
Product dimensions .................................................6
Venting Requirements...............................................7
Venting methods........................................................................7
Range hood installation............................................8
Electrical Connection................................................10
Description of the hood & controls.........................10
Manteinance...............................................................11
Warranty Information................................................12
©2013 Electrolux Home Products, Inc.
All rights reserved. Printed in Mexico
Important Safety Instructions
Important Safety Instructions
Read all instructions before using this
appliance.
Save these instructions for future
references
Approved for residential appliances
For residential use only
Do not attempt to install or operate your appliance
until you have read the safety precautions in this
manual. Safety items throughout this manual are
labeled with a WARNING or CAUTION based on the
risk type.
This symbol alerts you to
situations that may cause
serious body harm, death
or property damage.
This symbol alerts you to
situations that may cause
bodily injury or property
damage.
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn off power circuit at service panel and lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit
3
4
Important safety Instructions
READ AND SAVE THESE INSTRUCTIONS
Important safety Instructions
FOR GENERAL VENTILATING USE ONLY. DO NOT USE
TO EXHAUST HAZARDOUS OR EXPLOSIVE
MATERIALS OR VAPORS.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer
B. Before servicing or cleaning the unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
C. Installation Work and Electrical Wiring Must Be Done By
Qualified Person(s) In Accordance With all Aplicable Codes & Standards, Including Fire-rated Construction.
D. Sufficient air is needed for proper combustion and ex
hausting of gases through the flue (Chimney) of fuel burning equipment to prevent back- drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
F. Ducted systems must always be vented to the outdoors.
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE:
a)
b)
c)
d)
Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
Always turn hood ON when cooking at high heat or when flambeing food (l.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).
Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
Use proper pan size. Always use cookware appropriate for the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSOSNS,
IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a) SMOTHER FLAMES with a close - fitting lid, cookie sheet, or other metal tray, then turn off the gas burner or the electric element. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a class ABC extinguisher, and you already know how to operate it.
2) The fire is small and contained in the area where it started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
OPERATION
To reduce risk of fire and to properly exhaust air, be sure to
duct air outside - do not vent exhaust air into spaces within
walls, ceilings, attics, crawl spaces, or garages.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
Install this hood insert in accordance with all requirements
specified.
To Reduce The Risk Of Fire Or Electric Shock, Do Not
Use This Hood Insert With Any External Solid State Speed
Control Device.
Always leave safety grills and filters in place.Without these
components, operating blowers could catch onto hair,
fingers and loose clothing.
The manufacturer declines all responsibility in the event
of failure to observe the instructions given here for
installation,maintenance and suitable use of the product.
The manufacturer further declines all responsibility for injury
due to negligence and the warranty of the unit automatically
expires due to improper maintenance.
List of materials- Electrical & Installation
requirements
List of Materials
CAUTION!
Remove carton carefully. Wear gloves to protect
against sharp edges.
Parts supplied with unit for the installation
••
••
••
••
••
Hood canopy assembly with blower.
Lamp already installed.
Transition (31⁄4” x 10” rectangular)
Grease filter.
Hardware bag with:
•• Use and Care / Installation Manual
•• 3- 4x8 screws (to assemble Transition)
•• 6- 4,5x13 screws
•• 4- 10x50 screws
•• Torx 20 Adapter
Remove the protective film covering the product before putting into operation.
Tools/Materials required
••
••
••
••
••
••
••
••
••
••
••
••
••
••
••
••
Wire nuts
Metal duct length to suit installation
1
⁄2” Romex wire connector
Measuring tape
Pliers
Gloves
Knife
Safety glasses
Electric drill with 5⁄16” and 3⁄8” Bits
Spirit level
Duct tape
Screwdrivers:
•• Phillips (Posidrive) #2
•• Torx # 2
Wire cutter/stripper
Masking tape
Hammer
Saw, jigsaw or reciprocating saw
Electrical Requirements
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and
in conformance with National Electrical Code, ANSI/
NFPA 70 (latest edition), or CSA Standards C22.194, Canadian Electrical Code, Part 1 and C22.2 No.
0-M91 (latest edition) and all local codes and ordinances.
If codes permit and a separate ground wire is used, it
is recommended that a qualified electrician determine
that the ground path is adequate.
A copy of the above code standards can be obtained
from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
•• A 120 volt, 60 Hz., AC only, 15-amp, fused
electrical circuit is required.
•• If the house has aluminum wiring, follow the
procedure below:
1. Connect a section of solid copper wire to the
pigtail leads.
2. Connect the aluminum wiring to the added
section of copper wire using special co
nectors and/or tools designed and UL listed
for joining copper to aluminum.
Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection
must conform with local codes and industry accepted
wiring practices.
•• Wire sizes and connections must conform with
the rating of the appliance as specified on the
model/serial rating plate.
The model/serial plate is located behind the filter
on the top wall by the electrical box.
•• Wire sizes must conform to the requirements of
the National Electrical Code, ANSI/NFPA 70 (la
est edition), or CSA Standards C22. 1-94,
Canadian Electrical Code, Part 1 and C22.2
No. 0-M91 (latest edition) and all local codes and
ordinances.
5
6
Location requirements
Location Requirements
IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the hood
insert. It is the installer’s responsibility to comply with
installation clearances specified on the model/serial
rating plate. The model/serial rating plate is located
behind the left filter on the rear wall of the hood
insert.
The range hood location should be away from strong
draft areas, such as windows, doors and strong heating vents.
Grounded electrical outlet is required.
All openings in ceiling and wall where range hood will
be installed must be sealed.
For Mobile Home Installations
The installation of this hood insert must conform to the
Manufactured Home Construction Safety Standards,
Title 24 CFR, Part 328 (formerly the Federal Standard
for Mobile Home Construction and Safety, Title 24,
HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest
edition, or with local codes.
Product dimensions
"
(1.0 cm)
2 "
(6.5 cm)
29 " (74.0 cm)
35 " (89.2 cm)
7½"
(19.0 cm)
12"
(30.5 cm)
10"
(25.4 cm)
2"
(5.1 cm)
30" (76.2 cm)
36" (91.4 cm)
Serial Plate Location
•• Remove the grease filters.
•• The rating plate is located behind the filter by the
electrical box.
23" (58.4 cm)
Venting Requirements
Venting Requirements
•• Vent system must terminate to the outdoors.
•• Do not terminate the vent system in an attic or
other enclosed area.
•• Do not use 4” (10.2 cm) laundry-type wall caps.
•• Use metal vent only. Rigid metal vent is
recommended. Plastic or metal foil vent is not
recommended.
•• The length of vent system and number of elbows
should be kept to a minimum to provide efficient
performance.
For the most efficient and quiet operation:
•• Use no more than three 90° elbows.
•• Make sure there is a minimum of 24” (61.0 cm) of
straight vent between the elbows if more than 1
elbow is used.
•• Do not install 2 elbows together.
•• Use clamps to seal all joints in the vent system
and use furnace duct tape to fully seal joint
connection.
•• Use caulking to seal exterior wall or roof opening
around the cap.
•• The size of the vent should be uniform.
Cold weather installations
An additional back draft damper should be installed
to minimize backward cold air flow as part of the vent
system.
A thermal break should be installed to minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of
the thermal break.
The break should be as close as possible to where the
vent system enters the heated portion of the house.
Makeup air
Local building codes may require the use of makeup
air systems when using ventilation systems greater
than specified CFM of air movement. The specified
CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your area.
Venting Methods
Vent Exhaust Option
The hood is designed for vertical or horizontal
discharge.
•• Vertical discharge: Use a 31⁄4” x 10” rectangular duct.
•• Horizontal discharge: Use a 31⁄4” x 10” rectangular duct.
NOTE: Flexible vent is not recommended.
Flexible vent creates back pressure and air
turbulence that greatly reduce performance.
Vent system can terminate either through the
roof or wall. To vent through the wall, a 90° elbow
is needed.
Vertical
Discharge
Horizontal
Discharge
Preparation
Do not cut a joist or stud unless absolutely necessary.
If a joist or stud must be cut, then a supporting frame
must be constructed.
Fittings material is provided to secure the hood to
most types of walls/ceilings.
However, a qualified technician must verify suitability
of the materials in accordance with the type of wall/
ceiling.
Before making cutouts, make sure there is proper
clearance within the ceiling or wall for exhaust vent.
Hood installation height above cooktop is the users
preference. The lower the hood is above the cooktop,
the more efficient the capturing of cooking odors,
grease and smoke.
CAUTION:
Mount this hood so that the bottom edge is at 30”
(76.2 cm) minimum or 36”(91.4 cm) maximum above
the cooking surface. Household use, please, read
installation manual for specific application.
Check your ceiling height and the hood height maximum before you select your hood.
7
8
Range Hood Installation
Installation
Exhaust
transition/damper
Installation - Ducting version
After having chosen the vent option, proceed as
follows:
••
••
••
••
••
Prepare duct and conduit cut outs as needed.
If possible, disconnect and move freestanding
or slide-in range from cabinet opening to provide
easier access to rear wall. Otherwise put a thick,
protective covering over countertop, cooktop or range to protect from damage and debris. Select a flat surface for assembling the unit.
Cover that surface with a protective covering and
place all canopy hood parts and hardware in it.
Determine and mark the centerline on the wall
where the canopy hood will be installed.
Select a mounting height comfortable for the user
andmark on wall. Prepare duct and conduit cut outs as needed.
Remove the duct knockouts using a flat blade screwdriver and a small hammer.
Use the screwdriver by knocking out the pannel in similar fashion to a scalpel.
Take care of sharp edges.
Vertical
discharge
Pivot
Top/back
edge
Top/back
edge
Exhaust
transition/damper
Pivot
Mark holes
Select the vent option that your installation will require
and proceed to that section:
Outside top exhaust
(Vertical duct– 3 1⁄4”x 10” Rectangular)
Use the diagram or the hood as a template and mark
the locations on the cabinet for ductwork, electrical
wiring and keyhole screw slots.
30” Model: 2-7/8”
36” Model: 5-3/4”
Cabinet front
13/32”
Hood mounting
screws (4)
5”
7-1/2”
7-7/8”
Horizontal
discharge
NOTE: The exhaust adaptor/damper can be installed
up to 1 inch on either side of the hood center to accommodate offcenter ductwork. In extreme offcenter
installations, one end of the duct connector may need
to be trimmed to clear the electrical cable clamp.
Vertical duct
access hole
3-1/4”
2-1/2”
Electrical access hole
(in cabinet bottom)
Attach exhaust adaptor/damper over knockout opening with three exhaust adaptor screws. Make sure
damper pivot is nearest to top/back edge of hood.
Remove tape from damper flap.
Wood shims (recessed
bottom cabinets only)
5”
5/8”
Center line
Outside rear exhaust
(Horizontal duct– 3 1⁄4”x 10” Rectangular)
Use the diagram or the hood as a template and mark
the locations on the cabinet for ductwork, electrical
wiring and keyhole screw slots.
Wood shims (recessed
bottom cabinets only)
Cabinet front
21/32”
2-11/32”
Horizontal duct
access hole
5”
5”
30” Model: 4-15/32”
36” Model: 7”
3-1/4”
Cabinet
bottom
Hood mounting
screws (4)
13/32”
30” Model: 6-3/8”
36” Model: 8-7/8”
Electrical
access hole
(in wall)
Center line
Blower Motor Systems Installation
For recessed bottom cabinet only
If the cabinets have front, side or back trim, make 2
wood shims the width of the trim and attach them to
the cabinet bottom recess on both sides.
8-1/2” min. opening for ductwork
View From
Rear Cleats
1” x6” Min.
Mounting
Support
Installation to wall
(Horizontal duct– 31⁄4”x 10” Rectangular)
•• Use the diagram or the hood as a template and
mark the locations on the wall for ductwork,
electrical wiring and keyhole screw slots.
WALL
13-5/6” (30” Hood)
16-13/16” (36” Hood)
13-5/6” (30” Hood)
16-13/16” (36” Hood)
6-13/16” (30”Hood) 6-13/16” (30”Hood)
7” (36” Hood)
7” (36” Hood)
1-3/16”
permanent
mounting hole
21/32”
6-1/2” (30” Hood)
14-3/16” (36” Hood)
(30” Model)
(36” Model)
permanent
mounting hole
Center line
Install framing for hood support
•• If drywall is present, mark the screw hole
locations. Remove the template.
•• Cut away enough drywall to expose 2 vertical
studs at the holes location indicated by the
template. Install two horizontal supports at least 4” x 2” between two wall studs at the bottom and upper mounting holes installation location.
•• The horizontal support must be flush with the
room side of the studs. Use cleats behind both
sides of the support to secure to wall studs.
•• Reinstall drywall and refinish.
IMPORTANT- Framing must be capable of supporting
100 lbs.
Centerline of
Installation
Space
•• Cut holes at marked locations for duct and
electrical wiring.
•• For the vertical duct, cut out 3⁄4” extra toward the
front of the cabinet so you can move the duct
freely when installing the hood.
•• It may also ease installation by cutting the hole
101⁄2” instead of 10”.
•• Drive a mounting screw (from the hardware
packet) partway into each center of the narrow
neck of the keyhole slots marked on the cabinet
bottom.
•• Fix the wiring conduit to the hood.
•• Slide the hood back against the wall. Tighten the
mounting screws. Be sure the screw heads are in
the narrow neck of the keyhole slot.
•• Connect Ductwork to hood.
9
10
Electrical connection
Electrical connection
WARNING
Electrical Shock Hazard
Warning: Turn off power circuit at the service
panel before wiring this unit.
120 VAC, 15 or 20 Amp circuit required.
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST
ELECTRIC SHOCK, THE GREEN AND YELLOW
WIRE MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR HOME ELECTRICAL SYSTEM,
AND IT MUST UNDER NO CIRCUMSTANCES BE
CUT OR REMOVED.
Failure to do so can result in death or electrical
shock.
••
••
••
••
Remove the knockout and the Junction box
cover and install the conduit connector (cULus
listed) in junction box.
Run 3 wires; black, white and green, according
to the National Electrical Code and local codes
and ordinances, in 1⁄2” conduit from service
panel to junction box.
Connect black wire from service panel to black
or red in junction box, white to white and green
to green-yellow.
Close and secure junction box cover.
Final installation step
•• Replace the 2 lateral supports.
•• Replace filters.
•• Check operation of the hood.
If range hood does not operate:
•• Check that the circuit breaker is not tripped or
the house fuse blown.
•• Disconnect power supply.
•• Check that wiring is correct.
Keep your Installation Instructions and Use and Care
Guide close to range hood for easy reference.
Description of the Hood
2
1
3
4
5
6
1. Blower control switch
2. Light control switch
3. Lamp housings
4.
5.
6.
Grease filter Handle
Grease filter
Serial / Rating plate
(see page 6)
Controls
Use the high suction speed in cases of concentrated
kitchen vapours. It is recommended that the cooker
hood suction is switched on for 5 minutes prior to
cooking and to leave in operation during cooking and
for another 15 minutes approximately after terminating
cooking.
Description of control panel
1. Light Control
•• Turn the light switch (1) to the right 1 position for HIGH.
•• Turn the light switch (1) to the right 2 positions for LOW.
•• To turn the lights OFF, rotate the light switch (1) to the left to the OFF position.
2. Fan Control
The fan has 4 speeds.
•• Rotate the fan switch (2) to the right to turn the fan
ON. Continue to rotate the switch to the desired fan speed.
•• To turn the fan OFF, rotate the fan speed (2) switch
to the left to the OFF position.
Maintenance
Maintenance
ATTENTION! Before performing any maintenance
operation, isolate the hood from the electrical supply
by switching off at the connector and removing the
connector fuse.
Or if the appliance has been connected through a plug
and socket, then the plug must be removed from the
socket.
Cleaning
Do not spray cleaners directly to the control while
cleaning the Hood.The cooker hood should be
cleaned regularly (at least with the same frequency
with which you carry out maintenance of the fat filters)
internally and externally. Clean using the cloth dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING:
Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the filters
may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any
damage to the motor or any fire damage linked to
inappropriate maintenance or failure to observe the
above safety recommendations.
Grease Filter
To Remove Metal Grease Filters:
•• Use 2 hands to remove the metal grease filters.
Grasp filter handles, push toward the rear of
the range hood and pull down on the front handle
to remove.
To Reinstall Metal Grease Filters:
•• Grasp filter handles and place rear of filter into
rear track.
•• Push down on the rear handle and set the front of
the grease filter into the front track to secure.
•• Repeat for each filter.
•• Wash metal grease filters as needed in a
dishwasher or hand wash in a hot detergent
solution to clean.
Replacing the light bulb
CAUTION
Before replacing the lamps, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on accidentally.
NOTE: Turn off the lights and fan. Allow the lights to
cool before handling. If new lights do not operate be
sure lights are inserted correctly before calling service.
2
1
Replace Lights
Remove the damaged light (twist counter clockwise)
and replace with a new 120 Volt, 50 Watt (maximum)
50° halogen light made for a GU10 base, suitable for
use in open luminarie.
11
12
Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay
all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when
such appliance is installed, used and maintained in accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA
or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to
doors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER’S SOLE AND
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers
below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts
under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications
as described or illustrated are subject to change without notice.
USA
1.877.435.3287
Electrolux Major Appliances
North America
10200 David Taylor Drive
Charlotte, NC 28262
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement