Craftsman 11543 Owners manual

OPERATOR’S MANUAL
1/2 in. 19.2 VOLT HAMMER DRILL
VARIABLE SPEED
Model No.
315.115430
WARNING: To reduce the risk of injury,
the user must read and understand the
operator’s manual before using this
product.
Customer Help Line: 1-800-932-3188
batterIES and chargers
sold Separately
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
983000-759
11-21-07 (REV:02)
Save this manual for future reference
TABLE OF CONTENTS
Warranty........................................................................................................................................................................... 2
Introduction...................................................................................................................................................................... 2
General Safety Rules.....................................................................................................................................................3-4
Specific Safety Rules........................................................................................................................................................ 4
Symbols.........................................................................................................................................................................5-6
Features.........................................................................................................................................................................7-8
Assembly.......................................................................................................................................................................... 9
Operation...................................................................................................................................................................10-17
Maintenance..............................................................................................................................................................18-19
Exploded View and Parts List......................................................................................................................................... 20
Parts Ordering/Service......................................................................................................................................Back Page
WARRANTY
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN IT TO ANY
SEARS STORE OR OTHER CRAFTSMAN OUTLET IN THE UNITED STATES FOR FREE REPLACEMENT.
If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of
purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
INTRODUCTION
This tool has many features for making its use more ­pleasant and enjoyable. Safety, performance, and ­dependability
have been given top priority in the design of this product making it easy to maintain and operate.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry, or long hair can
be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
follow all instructions listed below may result in
electric shock, fire and/or serious injury. The term
“power tool” in all of the warnings listed below
refers to the mains-operated (corded) power tool
or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk
of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
Use battery only with charger listed.
MODEL
BATTERY PACK
(Li-ion) 315.113740
(130285003)
(Ni-Cd)
130279003
130279005
315.115430
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts, and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
CHARGER
(Multi-Chemistry)
315.25926
(140351001)
BATTERY PACK
CHARGER
(Ni-Cd)
130279003
130279005
1425301
(Item No. 911041)
315.115730
(Item No.
140301003)
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
GENERAL SAFETY RULES
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended could
result in a hazardous situation.
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
BATTERY TOOL USE AND CARE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SERVICE
Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
WARNING! To reduce the risk of injury, user must
read instruction manual.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
SPECIFIC SAFETY RULES
 Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged battery immediately.
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals. If exposed, flush with
water immediately.
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes
in contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
 Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also to prevent misuse of the product and
possible injury.
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the tool “live” and shock the operator.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
power tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
No Load Speed
Rotational speed, at no load
Class II Tool
Double-insulated construction
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any hot
surface.
min
no
.../min
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING: To avoid serious personal injury, do
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service we suggest you return the product
to your nearest SEARS PARTS AND REPAIR SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
not attempt to use this product until you read
thoroughly and understand completely the operator’s
manual. If you do not understand the warnings and
instructions in the operator’s manual, do not use this
product. Call the Craftsman Consumer Helpline at
1-800-932-3188 for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and, when needed, a full face shield. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
FEATURES
PRODUCT SPECIFICATIONS
Chuck............................................................1/2 in. Keyless
Motor................................................................... 19.2 V, DC
Switch...........................................................Variable Speed
No Load Speed......................... 0-400/0-1,400 r/min (RPM)
Hammer Speed..............................0-5,200/0-18,200 BPM*
Clutch................................................................. 24 Position
Torque.................................................................... 420 in.lb.
*Blows Per Minute
TWO-SPEED
GEAR TRAIN (HI-LO)
TORQUE
ADJUSTMENT RING
LEVEL
QUICK MODE
SELECTOR
KEYLESS
CHUCK
®
LEVEL
REAR VIEW
DIRECTION OF
ROTATION SELECTOR
(FORWARD/REVERSE/
CENTER LOCK)
AUXILIARY
HANDLE ASSEMBLY
SWITCH
TRIGGER
SCREWDRIVER
BITS
DEPTH STOP ROD
BIT STORAGE
Fig. 1
FEATURES
KNOW YOUR HAMMER DRILL
KEYLESS CHUCK
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all
operating features and safety rules.
The keyless chuck allows you to hand-tighten or release
the drill bit in the chuck jaws.
Auxiliary Handle
qUICK modE SElector
LEVELS
Levels are located on the top and end of the motor
housing to help keep the drill bit level during use.
Your drill is equipped with an auxiliary handle for ease of
operation and to prevent loss of control.
The mode selector allows for full torque, hammer drilling,
and the ability to drive screws with user adjusted torque.
BIT STORAGE
TORQUE ADJUSTMENT RING
Bits provided with the drill can be placed in the storage
area, located on the base of the drill.
Your drill has a 24-position clutch. The torque adjustment
ring can be turned to select the right amount of torque for
the application.
BLOWS PER MINUTE
TWO-SPEED GEAR TRAIN
This tool features an impact speed of 0-5,200/0-18,200
BPM (Blows Per Minute). Blows Per Minute is the number
of impacts per minute.
The two-speed gear train is designed for drilling or driving
at LO (1) or HI (2) speeds. A slide switch is located on top
of the drill for selecting either LO (1) or HI (2) speed.
DEPTH STOP ROD
VARIABLE SPEED
A depth stop rod has been supplied with this product to
assist in controlling the depth of drilled holes.
The switch trigger delivers higher speed with increased
trigger pressure and lower speed with decreased trigger
pressure.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/center lock)
Your drill has a direction of rotation (forward/reverse/
center lock) selector located above the switch trigger for
changing the direction of bit rotation. Setting the switch
trigger in the OFF (center lock) position helps reduce the
possibility of accidental starting when not in use.
ASSEMBLY
UNPACKING
WARNING: Do not attempt to modify this tool
This product requires assembly.
or create accessories not recommended for use
with this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list
are included.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
n Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
WARNING: To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the tool when assembling
parts.
ASSEMBLING AUXILIARY HANDLE
PACKING LIST
See Figure 2.
An auxiliary handle is packed with the drill for ease of
operation and to help prevent loss of control.
Hammer Drill with Auxiliary Handle Assembly
Bits (2)
n Insert and push screw all the way through slot on drill.
n Attach plate and auxiliary handle to screw and tighten.
n Insert end of depth stop rod into depth stop rod slot on
the back of the plate.
Operator’s Manual
WARNING: If any parts are missing do not operate
this tool until the missing parts are replaced. Failure
to do so could result in possible serious personal
injury.
DEPTH STOP ROD
PLATE
AUXILIARY
HANDLE
SCREW
SLOT
DEPTH STOP
SLOT
Fig. 2
OPERATION
WARNING: Do not allow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
WARNING: Do not use any attachments or accessories not recommended by the manufacturer of
this tool. The use of attachments or accessories not
recommended can result in serious personal injury.
LATCHES
APPLICATIONS
You may use this tool for the following purposes:
Drilling in wood
Drilling in ceramics, plastics, fiberglass, and laminates
Drilling in metals
Mixing paint
 Hammer drilling in concrete, brick, or other masonry
DEPRESS LATCHES
TO RELEASE BATTERY
PACK
This product will accept DieHard® 19.2 V lithium-ion battery packs and Craftsman 19.2 V nickel-cadmium battery
packs.
For complete charging instructions, refer to the Operator’s
Manual for the battery packs and chargers listed in the
General Safety Rules.
Fig. 3
CAUTION: When placing battery pack in the tool,
be sure raised rib on battery pack aligns with groove
inside tool and latches snap into place properly.
Improper assembly of battery pack can cause
damage to internal components.
TO INSTALL BATTERY PACK
TO REMOVE BATTERY PACK
See Figure 3.
Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Place battery pack in the tool. Align raised rib on
battery pack with groove inside tool.
 Make sure the latches on each side of the battery pack
snap into place and battery pack is secured in tool
before beginning operation.
See Figure 3.
Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Locate latches on end of battery pack and depress to
release battery pack from the tool.
 Remove battery pack.
10
OPERATION
FORWARD/REVERSE/CENTER LOCK
WARNING: Battery tools are always in operat-
See Figure 5.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
drill held in normal operating position, the direction of
rotation selector should be positioned to the left of the
switch trigger for drilling. The drilling direction is reversed
when the selector is to the right of the switch trigger.
ing condition. Therefore, switch should always be
locked when not in use or carrying at your side.
Switch trigger
See Figure 4.
To turn the drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when not
in use.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
CAUTION: To prevent gear damage, always allow
the chuck to come to a complete stop before changing the direction of rotation.
FORWARD/REVERSE/
CENTER LOCK
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool
the drill by running it without a load and at full speed.
FORWARD / REVERSE /
CENTER LOCK
Switch
trigger
REVERSE
Fig. 4
Note: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
SWITCH
TRIGGER
FORWARD
Fig. 5
11
OPERATION
KEYLESS CHUCK
TWO-SPEED GEAR TRAIN
See Figure 6.
The drill has a keyless chuck to tighten or release drill bits
in the chuck jaws. Grasp and hold the collar of the chuck
with one hand. Rotate the chuck body with your other
hand. The arrows on the chuck indicate which direction
to rotate the chuck body in order to LOCK (tighten) or
UNLOCK (release) the drill bit.
See Figure 7.
The drill has a two-speed gear train designed for drilling or
driving at LO (1) or HI (2) speeds. A slide switch is located
on top of the drill to select either LO (1) or HI (2) speed.
When using drill in the LO (1) speed range, speed will
decrease and unit will have more power and torque. When
using drill in the HI (2) speed range, speed will increase
and unit will have less power and torque. Use LO (1)
speed for high power and torque applications and HI (2)
speed for fast drilling or driving applications.
WARNING: Do not hold chuck body with one
hand and use power of the drill to tighten the chuck
jaws on the drill bit. The chuck body could slip in
your hand, or your hand could slip and come in
contact with the rotating drill bit. This could cause an
accident resulting in serious personal injury.
CHUCK
JAWS
TWO-SPEED
GEAR TRAIN (HI-LO)
LO
SPEED
1
2
UNLOCK
(RELEASE)
CHUCK
COLLAR
HI
SPEED
DRILL BIT
LOCK
(TIGHTEN)
CHUCK
BODY
Fig. 7
Fig. 6
12
OPERATION
adjustable torque clutch
BIT STORAGE
This product is equipped with an adjustable torque clutch
for driving different types of screws into different materials. To use the torque settings, rotate the mode selector
to the screw (
) setting. (The hammer mode (
)
and drill mode (
) are for full torque operations.) The
proper setting depends on the type of material and the
application.
See Figure 9.
When not in use, bits provided with the drill can be placed
in the storage area located on the base of the drill.
BIT
STORAGE AREA
ADJUSTing TORQUE
See Figure 8.
There are twenty-four torque indicator settings located on
the front of the drill.
 Rotate the adjusting ring to the desired setting.
• 1 - 4
For driving small screws
• 5 - 8
For driving screws into soft material
• 9 - 12 For driving screws into soft and hard materials
• 13 - 16 For driving screws into hard wood
SCREWDRIVER BIT
• 17 - 24 For driving large screws
Fig. 9
DRILL MODE
screw MODE
TO DECREASE
TORQUE
HAMMER MODE
TO INCREASE
TORQUE
MODE
SELECTOR
TORQUE
ADJUSTING RING
Fig. 8
13
OPERATION
INSTALLING BITS
WARNING: Make sure to insert the drill bit straight
See Figures 10 - 11.
 Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend to
use. Also, raise the front of the drill slightly to keep the
bit from falling out of the chuck jaws.
Insert the drill bit.
Tighten the chuck jaws on the drill bit.
CHUCK
JAWS
UNLOCK
(RELEASE)
into the chuck jaws. Do not insert the drill bit into the
chuck jaws at an angle then tighten, as shown in
figure 11. This could cause the drill bit to be thrown
from the drill, resulting in possible serious personal
injury or damage to the chuck.
Rotate the chuck clockwise to tighten the chuck jaws
securely on the bit.
Note: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws
CHUCK
COLLAR
DRILL BIT
LOCK
(TIGHTEN)
CHUCK
BODY
WRONG
RIGHT
Fig. 10
Fig. 11
REMOVING BITS
See Figure 10.
Lock the switch trigger by placing the direction of
rotation selector in the center position.
Rotate the chuck sleeve clockwise to open the chuck
jaws.
Note: Rotate the chuck body in the direction of the
arrow marked UNLOCK to loosen the chuck jaws. Do
not use a wrench to tighten or loosen the chuck jaws.
 Remove the drill bit.
14
OPERATION
USING THE AUXILIARY HANDLE ASSEMBLY
ADJUSTING THE AUXILIARY HANDLE ASSEMBLY
See Figures 12 - 13.
An auxiliary handle is packed with the drill for ease of
operation and to help prevent loss of control. The handle
can be rotated 360°, and it can also be mounted on the
opposite side for left hand use.
See Figure 13.
 Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
 Rotate the auxiliary handle assembly to the desired
location.
 Tighten the auxiliary handle assembly securely by turning the knob clockwise.
To adjust the auxiliary handle assembly, loosen the handle
assembly by turning the handle counterclockwise.
Rotate the auxiliary handle assembly to the desired
operating position.
ADJUSTING THE DEPTH STOP ROD
See Figure 13.
 Lock the switch trigger by placing the rotation selector
in the center position.
 Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
 Adjust the depth stop rod so that the drill bit extends
beyond the end of the rod to the required drilling
depth.
 Tighten the auxiliary handle assembly by turning the
knob clockwise.
Securely tighten by turning the auxiliary handle clockwise.
Be sure the auxiliary handle is securely tightened against
the depth gauge clamp. This secures the depth stop rod
at the desired depth of cut. It also secures the auxiliary
handle.
NOTE: For convenience and ease of starting threads, the
hex nut has been trapped inside the molded slot in the
auxiliary handle.
The depth stop rod helps control the depth of drilled
holes.
NOTE: When properly installed, the teeth on the depth
stop rod should be aligned with the teeth indicator on the
depth gauge clamp.
DEPTH STOP ROD
SCALE
TEETH
Adjust the depth stop rod so that the drill bit extends
beyond the end of the rod to the required drilling depth.
When drilling holes with the depth stop rod installed, the
desired hole depth has been reached when the end of the
rod comes in contact with the surface of the workpiece.
HEX BOLT
TO INCREASE
DRILLING
DEPTH
DRILL BIT
PLATE
AUXILIARY
HANDLE
HEX SLOT
TO DECREASE
DRILLING DEPTH
HEX BOSS
TO
TIGHTEN
TO
TIGHTEN
DRILLING DEPTH
TO
LOOSEN
Fig. 12
15
Fig.
15
TO
LOOSEN
Fig. 13
OPERATION
SELECTING A DRILLING MODE
LEVEL
®
See Figure 14.
To adjust for type of drilling, slide the mode selector on
the side of the motor housing to hammer mode, screw
mode, or drilling mode.
Select screw mode for driving screws. Screw mode operates with user adjusted torque. (See Adjustable Torque
Clutch.)
Drill mode is for full torque operations only and bypasses
the clutch setting. Select drill mode when drilling with
twist drills, hole saws, etc., in soft materials, or when the
application calls for full torque of the drill.
Select hammer mode for masonry, brick, tile, and concrete. For maximum performance, use carbide-tipped
impact masonry bits.
To use the hammer mode:
 Rotate the mode selector to the hammer mode.
 Apply light pressure and medium speed for best results in brick.
 Apply additional pressure and high speed for hard
materials such as concrete.
 When drilling holes in tile, practice on a scrap piece to
determine the best speed and pressure.
NOTE: The hammer drill has not been designed for reverse hammering.
6
DRILLING
See Figures 15 - 16.
Levels are located on the top and end of the motor housing to help keep the drill bit level during use.
 Check the direction of rotation selector for the correct
setting (forward or reverse).
 Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
 Hold the drill firmly and place the bit at the point to be
drilled.
 Depress the switch trigger to start the drill.
 Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
DRILL MODE
screw MODE
TO DECREASE
TORQUE
Fig. 15
HAMMER MODE
WARNING: Be prepared for binding at bit breakthrough. When these situations occur, drill has a
tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
 When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will prevent the drill bit from slipping off-center as the hole is
started.
 When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
TO INCREASE
TORQUE
MODE
SELECTOR
TORQUE
ADJUSTING RING
Fig. 14
16
OPERATION
METAL DRILLING
 If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE: This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible through
the vent slots on the housing. This is normal and is the
action of the brake.
For maximum performance, use high speed steel bits for
metal or steel drilling.
 Select normal drilling mode.
 Begin drilling at a very low speed to prevent the bit
from slipping off the starting point.
 Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much pressure will:
• Overheat the drill;
• Wear the bearings;
• Bend or burn bits; and
• Produce off-center or irregular-shaped holes.
 When drilling large holes in metal, start with a small bit,
then finish with a larger bit. Also, lubricate the bit with
oil to improve drilling action and increase bit life.
WOOD DRILLING
For maximum performance, use high speed steel bits for
wood drilling.
 Select normal drilling mode.
 Begin drilling at a very low speed to prevent the bit
from slipping off the starting point. Increase the speed
as the drill bit bites into the material.
 When drilling through holes, place a block of wood
behind the workpiece to prevent ragged or splintered
edges on the back side of the hole.
MASONRY DRILLING
For maximum performance, use carbide-tipped masonry
impact bits when drilling holes in brick, tile, concrete, etc.
LEVEL
 Slide adjustment button on hammer drill left for hammer mode.
 Apply light pressure and medium speed for best results
in brick.
 Apply additional pressure for hard materials such as
concrete.
 When drilling holes in tile, practice on a scrap piece to
determine the best speed and pressure. Begin drilling
at a very low speed to prevent the bit from slipping off
the starting point.
Fig. 16
17
MAINTENANCE
WARNING: When servicing, use only identical
GENERAL MAINTENANCE
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING: Always wear safety goggles or safety
glasses with side shields when using compressed air
to clean tools. If the operation is dusty, also wear a
dust mask.
WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
WARNING: To avoid serious personal injury, always
remove the battery pack from the tool when cleaning
or performing any maintenance.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
BATTERIES
This product will accept DieHard® 19.2 V lithium-ion
battery packs and Craftsman 19.2 V nickel-cadmium
battery packs.
To preserve natural resources, please
recycle or dispose of batteries ­properly.
The batteries for this product have been designed
to provide maximum trouble-free life. However, like
all batteries, they will eventually wear out. Do not
disassemble battery pack and attempt to replace the
batteries. Handling of these batteries, especially when
wearing rings and jewelry, could result in a serious burn.
Li - Ion
This product uses nickel-­cadmium and
lithium-ion batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash.
Consult your local waste authority for
information ­regarding available recycling
and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
For lithium-ion batteries:
WARNING: Upon removal, cover the battery
 Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
pack’s terminals with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble battery
pack or remove any of its components. Lithium-ion
and nickel-cadmium batteries must be recycled or
disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short
circuit may result. Keep away from children. Failure
to comply with these warnings could result in fire
and/or serious injury.
 Store the battery pack where the temperature is below
80°F and away from moisture.
 Store battery packs in a 30%-50% charged condition.
 Every six months of storage, charge the pack as
normal.
For nickel-cadmium batteries:
 Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
 Store the battery pack where the temperature is below
80°F.
 Store battery packs in a “discharged” condition.
18
MAINTENANCE
chuck removal
MALLET
See Figures 17 - 19.
The chuck may be removed and replaced by a new one.
Lock the switch trigger by placing the direction of rotation selector in center position.
Insert a 5/16 in. or larger hex key into the chuck of the
drill and tighten the chuck jaws securely.
Tap the hex key sharply with a mallet in a clockwise
direction. This will loosen the screw in the chuck for
easy removal.
Open the chuck jaws and remove the hex key. Using a
screwdriver, remove the chuck screw by turning it in a
clockwise direction.
Note: The chuck screw has left hand threads.
MALLET
Fig. 19
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on the spindle and develop
a wobble. Also, the chuck screw may become loose,
causing the chuck jaws to bind and prevent them from
closing. To tighten:
CHUCK JAWS
HEX KEY
Lock the switch trigger by placing the direction of rotation selector in the center position.
 Open the chuck jaws.
Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap the hex key sharply with a mallet in
a clockwise direction. This will tighten the chuck on the
spindle.
Open the chuck jaws and remove the hex key.
Tighten the chuck screw.
KEYLESS
CHUCK
Fig. 17
 Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the
spindle. It can now be unscrewed by hand.
SCREWDRIVER
Fig. 18
19
CRAFTSMAN 19.2V CORDLESS HAMMER DRILL - 315.115430
The model number will be found on a plate attached to the motor housing. Always mention the
model ­number in all correspondence regarding your HAMMER DRILL or when ordering repair
parts.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
4
3
2
1
5
6
PARTS LIST
Key Part
No.
Number
DescriptionQty.
1
6613401
Chuck Screw....................................................................................1
2
690033058
Chuck................................................................................................1
3
940237091
Data Plate.........................................................................................1
4
940114128
Logo Plate.........................................................................................1
5
300188033
Auxiliary Handle Assembly...............................................................1
6
6341203
Depth Stop Rod................................................................................1
983000759
Operator’s Manual
20