Aeg BS7304001M User Manual

BS7304001
EN OVEN
USER MANUAL
2
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
ACCESSORIES AND CONSUMABLES
In the AEG webshop, you’ll find everything you need to keep all your AEG
appliances looking spotless and working perfectly. Along with a wide range of
accessories designed and built to the high quality standards you would expect,
from specialist cookware to cutlery baskets, from bottle holders to delicate
laundry bags…
Visit the webshop at:
www.aeg.com/shop
Contents
3
CONTENTS
4
7
9
10
12
15
17
18
20
23
27
28
Safety information
Product description
Before first use
Control panel
Daily use
Clock functions
Automatic programmes
Using the accessories
Additional functions
Care and cleaning
What to do if…
Environment concerns
The following symbols are used in this user
manual:
Important information concerning your
personal safety and information on how to
avoid damaging the appliance.
General information and tips
Environmental information
Subject to change without notice.
4
Safety information
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the supplied instructions.
The manufacturer is not responsible if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for future reference.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
• Do not let persons, children included, with reduced physical sensory, reduced mental
functions or lack of experience and knowledge use the appliance. They must have supervision or instruction for the operation of the appliance by a person who is responsible for
their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep children and pets away from the appliance when it operates or when it cools down.
Accessible parts are hot.
• If the appliance has a child safety device, we recommend that you activate it.
Installation
WARNING!
Only a qualified person must install this appliance.
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged appliance.
Obey the installation instruction supplied with the appliance.
Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
Do not pull the appliance by the handle.
Keep the minimum distance from the other appliances and units.
Make sure that the appliance is installed below and adjacent safe structures.
The sides of the appliance must stay adjacent to appliances or to units with the same
height.
Electrical connection
WARNING!
Risk of fire and electrical shock.
• All electrical connections should be made by a qualified electrician.
• The appliance must be earthed.
• Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof socket.
Safety information
5
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains plug and to the mains cable. Contact the
Service or an electrician to change a damaged mains cable.
• Do not let mains cables to come in touch with the appliance door, specially when the
door is hot.
• The shock protection of live and insulated parts must be fastened in such a way that it
cannot be removed without tools.
• Connect the mains plug to the mains socket only at the end of the installation. Make
sure that there is access to the mains plug after the installation.
• If the mains socket is loose, do not connect the mains plug.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
• Use only correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors.
• The electrical installation must have an isolation device which lets you disconnect the
appliance from the mains at all poles. The isolation device must have a contact opening
width of minimum 3 mm.
Use
WARNING!
Risk of injury, burns or electric shock or explosion.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Use this appliance in a household environment.
Do not change the specification of this appliance.
Make sure that the ventilation openings are not blocked.
Do not let the appliance stay unattended during operation.
Deactivate the appliance after each use.
Internally the appliance becomes hot when in operation. Do not touch the heating elements that are in the appliance. Always use oven gloves to remove or put in accessories
or ovenware.
Be careful, when you open the appliance door while the appliance is in operation. Hot air
can release.
Do not operate the appliance with wet hands or when it has contact with water.
Do not apply pressure on the open door.
Do not use the appliance as a work surface or as a storage surface.
Always keep the appliance door closed when the appliance is in operation.
Open the appliance door carefully. The use of ingredients with alcohol can cause a mixture of alcohol and air.
Do not let sparks or open flames to come in contact with the appliance when you open
the door.
Do not put flammable products or items that are wet with flammable products in, near
or on the appliance.
WARNING!
Risk of damage to the appliance.
6
Safety information
• To prevent damage or discoloration to the enamel:
– Do not put ovenware or other objects in the appliance directly on the bottom.
– Do not put aluminium foil directly on the bottom of the appliance.
– do not put water directly into the hot appliance.
– do not keep moist dishes and food in the appliance after you finish the cooking.
– be careful when you remove or install the accessories.
• Discoloration of the enamel has no effect on the performance of the appliance. It is not
a defect in the sense of the warranty law.
• Use a deep pan for moist cakes. Fruit juices cause stains that can be permanent.
Steam Cooking
WARNING!
Risk of burns and damage to the appliance.
• Do not open the appliance door during steam cooking. Steam can release.
Care and Cleaning
WARNING!
Risk of injury, fire or damage to the appliance.
• Before maintenance, deactivate the appliance and disconnect the mains plug from the
mains socket.
• Make sure the appliance is cold. There is the risk that the glass panels can break.
• Replace immediately the door glass panels when they are damaged. Contact the Service.
• Be careful when you remove the door from the appliance. The door is heavy!
• Clean regularly the appliance to prevent the deterioration of the surface material.
• Remaining fat or food in the appliance can cause fire.
• Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads, solvents or metal objects.
• If you use an oven spray, obey the safety instructions on the packaging.
• Do not clean the catalytic enamel (if applicable) with any kind of detergent.
Internal light
• The type of light bulb or halogen lamp used for this appliance, is only for household appliances. Do not use it for house lighting.
WARNING!
Risk of electrical shock.
• Before replacing the lamp, disconnect the appliance from the power supply.
• Only use lamps with the same specifications.
Disposal
WARNING!
Risk of injury or suffocation.
Product description
• Disconnect the appliance from the mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and pets to get closed in the appliance.
PRODUCT DESCRIPTION
General overview
1
2
3
4
5
6
5
4
11
3
7
2
8
1
9
10
1
2
3
4
5
6
7
8
9
10
11
Control panel
Electronic programmer
Water drawer
Socket for the core temperature sensor
Heating element
Oven lamp
Fan
Rear wall heating element
Steam generator
Shelf support, removable
Shelf positions
7
8
Product description
Accessories
• Wire shelf
For cookware, cake tins, roasts.
• Baking tray
For cakes and biscuits.
• Grill / roasting pan
To bake and roast or as pan to collect fat.
• Steam set
One unperforated and one perforated food
container.
The steam set drains the condensing water
away from the food during steam cooking.
Use it to prepare food that should not be in
the water during the cooking (e.g. vegetables, pieces of fish, chicken breast). The set is
not suitable for food that needs to soak in
the water (e.g. rice, polenta, pasta).
Before first use
9
• Sponge
For absorbing residual water from the steam
generator.
• Core Temperature Sensor
To measure how far the food is cooked.
BEFORE FIRST USE
WARNING!
Refer to "Safety information" chapter.
Initial Cleaning
• Remove all parts from the appliance.
• Clean the appliance before first use.
Refer to chapter "Care and Cleaning".
First connection to the mains
After first connection to the mains all symbols in the display are on for some seconds. For
the subsequent few seconds the display shows software version.
First setting the time of day
After the software version goes off, the display shows "h" and "12:00".
Setting the time of day:
or
to set hours.
1. Touch
or .
2. Touch
or
to set minutes.
3. Touch
or .
4. Touch
The Temperature/Time display shows new time.
Changing the time of day
You can change the time of day only if the appliance is off.
Touch . flashes in the display. To set new time of day use the above procedure.
10
Control panel
CONTROL PANEL
Electronic programmer
1
2
3
4
5
6
7
8
9
10
Use the sensor fields to operate the appliance.
Sensor Field
Function
-
DISPLAY
Shows the current settings of the appliance.
2
ON / OFF
To activate and deactivate the appliance.
3
OPTIONS
To set an oven function or programme.
Straight access to the oven function when the
appliance is off.
4
MY FAVOURITE PROGRAMME
You can store your favourite programme. Use it
to access your favourite programme directly, also
when the appliance is off.
5
TEMPERATURE / FAST
HEAT UP
To set and examine cavity temperature or core
temperature sensor temperature. If you press it
and hold for three seconds, it turns Fast heat up
function ON and OFF.
Straight access to the temperature setting of
the first oven function when the appliance is
off.
6
UP, DOWN
To choose an oven function, clock function and
to set the minute minder, temperature or time of
day.
7
OK
8
OVEN LIGHT
9
CLOCK
To set the clock function.
10
MINUTE MINDER
To set the minute minder.
1
Description
To confirms the selection or setting.
To set the oven lamp on or off.
11
Control panel
Display
1
2
7
3
6
5
4
Oven function symbol
Temperature / Time display
Clock / Residual heat display (also Minute minder and Time of day)
Residual heat indicator
Indicators for the clock functions (refer to the table "Clock functions")
Heat up indicator
Number of oven function / programme
1
2
3
4
5
6
7
Other indicators of display
Symbols
/
/
Name
Description
Options
You can choose an oven function.
Automatic programme
You can choose an oven programme.
My favourite programme
The favourite programme operates.
kgr / gr
An oven programme with weight input operates.
h / min
A clock function operates.
Temperature / fast heat up
The function operates.
Temperature
You can examine or change the temperature.
Core temperature sensor
The core temperature sensor is in the core temperature
sensor socket.
Oven light
The light is off.
Minute minder
The minute minder function operates.
Heat up indicator
If you set an oven function, the bars in the display come on one by one. The bars show
that the temperature in the appliance increases or decreases.
When the appliance is at the set temperature Heat up indicator goes off the display.
12
Daily use
DAILY USE
WARNING!
Refer to "Safety information" chapter.
To operate the appliance you can use:
• The manual mode - to set an oven function, the temperature and the cooking time
manually.
• automatic programmes - to prepare a dish when you do not have knowledge or experience in cooking.
Setting the oven function
1.
2.
3.
Touch .
The display shows a preset temperature, symbol and number of the oven function.
flashes in the display.
or
to set an oven function.
Touch
or the appliance starts automatically after five seconds.
Touch
If you activate the appliance with or and do not set any oven function or programme
the appliance will deactivate automatically after 20 seconds.
Oven Functions
Oven function
1
2
Full Steam
Application
For vegetables, fish, potatoes, rice, pasta or special sidedishes.
Half Steam + Heat For dishes with a high moisture content and for poaching
fish, custard royale and terrines.
3
Quarter Steam +
Heat
To bake bread, roast large pieces of meat or to warm up chilled and frozen meals.
4
ECO Steam
ECO functions let you to optimize the energy consumption
during cooking. Thus it is necessary to set the cooking time
first. To get more information about the recommended settings, refer to the cooking tables with the equivalent usual
oven function.
5
Moist Fan Baking
For energy-saving baking and cooking of mainly dry bakery
items as well as for baking in tins on one shelf position.
6
True Fan Cooking
To bake maximum on three oven shelf positions at the same
time. Decrease the oven temperatures (20-40 °C) compared
with Conventional. And to dry food.
7
Pizza Setting
To bake on one shelf position food with a more intensive
browning and a crispy base. Decrease the oven temperatures
(20-40 °C) compared with Conventional cooking.
8
Slow Cook
To prepare very lean, tender roasted food.
13
Daily use
Oven function
Application
9
Conventional
Cooking
To bake and roast food on one shelf position.
10
Frozen Foods
To make your convenience food like e.g. French Fries, Wedges, spring rolls crispy.
11
Turbo Grilling
To roast larger meat joints or poultry with bones on one
shelf position. Also to gratinate and to brown.
12
Fast Grilling
13
Grilling
14
Keep Warm
15
Defrost
16
Bottom Heat
To bake cakes with a crispy base, and to preserve food.
17
ECO Roasting
ECO functions let you to optimize the energy consumption
during cooking. Thus it is necessary to set the cooking time
first. To get more information about the recommended settings, refer to the cooking tables with the equivalent usual
oven function.
18
Steam Cleaning
To grill flat food in large quantities. To toast bread.
To grill flat food in the middle of the grill. To toast bread.
To keep food warm.
To defrost frozen food.
To clean the oven interior using steam.
Changing the oven temperature
Touch
/
to change the temperature in steps of 5 °C.
When the appliance is at the set temperature, an acoustic signal operates three times and
the Heat up indicator goes off.
Examining the oven temperature
You can examine the temperature in the appliance when the function or programme operates.
.
1. Touch
The Temperature / Time display shows the temperature in the appliance.
If you want to change the oven temperature, touch
2.
one more time and use
or
to go back to the set temperature or the display will show it automatically
Touch
after five seconds.
Fast heat up function
The fast heat up function decreases the heat up time.
.
14
Daily use
Do not put food in the oven when the fast heat up function operates.
for more then three seconds.
Activating the fast heat up function: Touch and hold
If you activate the fast heat up function, the bars on the display flash one by one to
show that the function operates.
The fast heat up is not available with every oven function. An acoustic signal operates if the
fast heat up is not available for set function.
Steam cooking
The water drawer cover is in the control panel.
1.
2.
Press the cover to open the water drawer.
Fill the water drawer with 800 ml of water.
The water supply is sufficient for approximately 40 minutes.
CAUTION!
Do not put water directly into the steam generator!
Use only water as the liquid. Do not use filtered (demineralised) or distilled water.
3.
4.
5.
6.
Activate the appliance.
Set the Steam function (refer to the table "Oven functions") and temperature.
Touch to set the DURATION or END function (refer to "Setting the END" or "Setting
the DURATION"). The first steam shows after approximately 2 minutes. An acoustic signal sounds when the temperature is approximately 96°C.
The signal sounds again at the end of the cooking time.
Touch to deactivate the acoustic signal and the appliance.
When the steam generator has been emptied, an acoustic signal sounds.
When the appliance has cooled down, soak up all remaining water from the steam generator with the Sponge. If necessary, clean the steam generator with some vinegar.
Let the appliance dry fully with the door open.
Energy saving
The appliance has some features that help you save energy during everyday cooking:
• Residual heat:
– the oven function or programme operates: the heating elements are deactivated 10%
time earlier (the lamp and fan continue to operate). The condition: the cooking time is
longer then 30 minutes or you use the clock functions (Duration, End, Time delay).
– the oven is off: you can use the heat to keep the food warm. The indication: the clock/
Residual heat display shows the remaining temperature, the bars show the decreasing
temperature.
• Oven lamp off - touch to deactivate the oven lamp during cooking;
Clock functions
• Display off - if necessary, deactivate the appliance. Touch
until the display goes out (or on).
• Eco functions - refer to "Oven function".
and
15
at the same time
CLOCK FUNCTIONS
SYMBOL
FUNCTION
DESCRIPTION
COUNT UP TIMER
To set count up. It shows how long the appliance operates.
This function has no effect on the operation of the appliance.
TIME OF DAY
To examine the time of day. For changing the time of day refer to 'Setting the time of day'.
DURATION
To set how long the appliance operates.
END
To set when the appliance deactivates. You can use Duration
and End at the same time (Time delay), if the appliance is to
be activate and deactivate automatically later.
SET+GO
To start the appliance with necessary settings with only one
touch of the sensor field, any time later.
Count Up Timer
Use the Count Up Timer to monitor how long the appliance operates. It is on immediately
when the appliance starts to heat.
Reset the Count Up Timer: touch again and again until flashes in the display. Touch
until the display shows "00:00" and the Count Up Timer starts to count up again.
You can not use Count Up Timer when Duration or End is set.
Setting the DURATION
1.
2.
3.
4.
5.
Activate the appliance and set an oven function and temperature.
Touch again and again until the display shows .
flashes in the display.
or
to set minutes for DURAUse
TION.
to confirm
Touch
or
to set hours for DURATION.
Use
If you touch or
during setting hours for DURATION, the appliance goes to setting of
the END function.
6. When the set time ends, an acoustic signal operates for two minutes.
symbol and time setting flash in the display. The appliance deactivates.
Touch any sensor field or open the oven door to stop an acoustic signal.
7. Deactivate the appliance.
16
Clock functions
Setting the END
1.
2.
3.
4.
5.
6.
Activate the appliance and set an oven function and temperature.
Touch again and again until the display shows .
flashes in the display.
or
to set END (first you set minutes and then hours) and
or
Use
confirm.
When the set time ends, an acoustic signal operates for two minutes.
symbol and time setting flash in the display. The appliance deactivates.
Touch any sensor field or open the oven door to stop an acoustic signal.
Deactivate the appliance.
to
Setting the SET+GO
To start of the appliance with necessary settings with only one touch of the sensor field,
any time later.
1. Set an oven function (or programme) and temperature (refer to "Setting the oven
function" and "Changing the oven temperature").
2. Set DURATION (refer to "Setting the DURATION").
3. Touch again and again until will flash in the display.
to set the SET+GO function.
4. Touch
The display shows and with a dot. This dot shows which clock function is activated.
5. Touch any sensor field (apart from ON/OFF) to start the SET+GO function.
You can use SET+GO function only if DURATION is set.
Check result (selected models only)
If you set END or DURATION function, 2 minutes before end of cooking an acoustic signal
sounds and lamp activates. The appliance goes to the setting of the END or DURATION
function. During these two minutes you can examine the cooking results and, if necessary,
add END or DURATION time.
Setting the Time delay function
DURATION and END can be used at the same time, if the oven is to be switched on
and off automatically later. In this case first set DURATION and then END function
(refer to "Setting the DURATION" and "Setting the END ").
When the Time delay function is activated the display shows static symbol of the oven
function, with a dot and . The dot shows which clock function is on in the Clock/
Residual heat display.
Setting the MINUTE MINDER
Use the MINUTE MINDER to set a countdown (maximum 23 h 59 min). This function has no
effect on the operation of the oven. You can set the MINUTE MINDER any time, also if the
appliance is off.
1. Touch .
Automatic programmes
2.
3.
4.
5.
17
and "00" flash in the display.
or
to set MINUTE MINDER.
Use
First you set seconds and then minutes
and hours.
or the MINUTE MINDER starts
Touch
automatically after five seconds.
When set time ends, an acoustic signal
operates for two minutes and "00:00"
and flash in the display.
Touch any sensor field or open the oven door to stop an acoustic signal.
AUTOMATIC PROGRAMMES
WARNING!
Refer to "Safety information" chapter.
There are 25 automatic programmes and recipes. Use an automatic programme when you
do not have a knowledge or experience how to prepare a dish. You can find the recipes for
the automatic programmes in the "Recipe book".
There are three types of automatic programmes:
• Automatic recipes;
• Automatic programmes with weight input;
• Automatic programmes with food sensor;
Automatic recipes
Setting an automatic recipe:
1. Touch two times until the display shows .
The display shows symbol and number of the automatic programme.
or
to choose the automatic recipes.
2. Touch
or the automatic recipe activates automatically after five seconds.
3. Touch
4. When set time ends, an acoustic signal operates for two minutes. Symbol flashes.
The appliance deactivates.
5. Touch any sensor field or open the oven door to stop an acoustic signal.
Automatic programmes with weight input
If you set the weight of the meat, the appliance calculates the roasting time.
1. Touch again and again until the display shows .
or
to set the weight programme (refer to "Recipe book").
2. Touch
The display shows: cooking time, duration symbol , a default weight, a unit of
measurement (kg, g).
or the settings save automatically after five seconds.
3. Touch
18
Using the accessories
4.
5.
6.
The appliance starts. A symbol of the weight unit flashes in the display. During this
or
. Touch
.
time you can change the default weight value with
When set time ends, an acoustic signal operates for two minutes. flashes.
The appliance deactivates.
Touch any sensor field or open the oven door to stop an acoustic signal.
Automatic programmes with core temperature sensor
The core temperature of the food is default and fixed in programmes with core temperature
sensor. The programme ends when the appliance is at the set core temperature.
1. Touch again and again until the display shows .
2. Install the core temperature sensor (refer to "The core temperature sensor").
or
to set the core temperature sensor programme.
3. Touch
When a core temperature sensor programme is set, the display shows the cooking
.
time, and
or the settings save automatically after five seconds.
4. Touch
5. When set time ends, an acoustic signal operates for two minutes. flashes.
The appliance deactivates.
6. Touch any sensor field or open the oven door to stop an acoustic signal.
USING THE ACCESSORIES
WARNING!
Refer to "Safety information" chapter.
Core Temperature Sensor
The core temperature sensor measures the core temperature of the meat. When the meat is
at the set temperature, the appliance deactivates.
There are two temperatures to set:
• The oven temperature: refer to the table for roasting in the recipe book.
• The core temperature: refer to the table for the core temperature sensor in the recipe
book.
Only use the core temperature sensor supplied or original replacement parts.
1.
Activate the appliance.
Using the accessories
2.
3.
4.
5.
19
Put the point of the core temperature
on the
sensor (with the symbol
handle) into the centre of the meat.
Put the plug of the core temperature
sensor into the socket at the front of
the appliance.
The display shows a flashing symbol
and the default set core temperature. The temperature is 60 °C during
the first use, and the last set value during each subsequent use.
or
to set the core temperTouch
ature.
or the settings save autoTouch
matically after 5 seconds.
You can set the core temperature only when the symbol
flashes. If the display shows a
before you set the core temperature, use
and
or
to set a new
static symbol
value.
6. Set the oven function and, if necessary, the oven temperature.
The display shows the current core temperature and (which shows the relation between the set oven temperature and the current oven temperature).
The core temperature sensor must stay in the meat and in the socket during the cooking.
While the appliance calculates the approximate duration time, the value of the Count Up
Timer function shows in the Timer/Residual heat display. When the first calculation ends,
the Timer/Residual heat display shows -, and then the approximate duration of the cooking.
The appliance continues to calculate the duration during the cooking. The display updates
at intervals with the new duration value.
7. When the meat is at the set core temperature, the core temperature and
flash. An
acoustic signal sounds for two minutes.
Touch a sensor field to deactivate the acoustic signal.
8. Remove the core temperature sensor from the socket and remove the meat from the
appliance.
WARNING!
Be careful when you remove the core temperature sensor. It is hot. There is a risk of burns.
9. Deactivate the appliance.
When you put the core temperature sensor into the socket, you cancel the settings for the
clock functions.
20
Additional functions
When you cook with the core temperature sensor, you can change the temperature shown
in the Temperature/Time display. After you put the core temperature sensor in the socket
and set an oven function and temperature, the display shows the current core temperature.
Touch
again and again to see three other temperatures:
• The current core temperature
• The oven set temperature
• The current oven temperature.
The set core temperature changes into current core temperature and current oven temperature changes into set oven temperature.
Inserting the Oven Accessories
The deep pan and the wire shelf have side edges.
These edges and the shape of the guide-bars causes the anti-tilt safety for the oven accessories.
Inserting the wire shelf and the deep pan together
Put the wire shelf on the deep pan. Push the deep
pan between the guide-bars of one of the shelf
positions.
ADDITIONAL FUNCTIONS
My Favourite Programme function
Use this function to save your favourite settings of temperature and time for an oven function or programme.
1. Set the temperature and time for an oven function or programme.
2. Touch and hold for more than three seconds.
An acoustic signal sounds.
Additional functions
21
3. Deactivate the appliance.
Using My Favourite Programme function:
• To activate the function touch . The appliance activates your favourite programme.
• To deactivate the function touch . The appliance deactivates your favourite programme.
When the function operates, you can change the time and temperature.
Child Lock
The Child Lock prevents an accidental operation of the appliance.
Activating and deactivating the Child Lock function:
1. Deactivate the appliance with . Do not set an oven function.
at the same time for 2 seconds. An acoustic signal sounds.
2. Touch and hold and
SAFE comes on/goes out in the display.
If the oven has Pyro Cleaning function, the door is locked.
SAFE comes on in the display when you touch a sensor field.
Control lock
You can activate the function only when the appliance operates. The Control Lock prevents
an accidental change of the oven function.
Activating/deactivating the control lock function:
1. Activate the appliance.
2. Activate an oven function or setting.
at the same time for 2 seconds. An acoustic signal sounds.
3. Touch and hold and
Loc comes on/goes out in the display.
You can deactivate the appliance when the control lock is on. When you deactivate the appliance, the control lock deactivates.
If the oven has the Pyro cleaning function, the door is locked.
Loc comes on in the display when you touch a sensor field.
Settings menu
The settings menu lets you to add or remove functions from the main menu (for example:
you can set on or off the Residual heat indicator). Settings menu has maximum seven settings (from SET1 to SET7). The number of the settings is different for different models. Look
into the table below to see the possible value of each setting.
Settings menu
Indicator of the setting menu
Description
Value to set
SET1
SET+GO
ON/OFF
SET2
RESIDUAL HEAT INDICATOR
ON/OFF
SET3
KEY TONE
CLIC/BEEP/OFF
SET4
FAULTY TONE
ON/OFF
22
Additional functions
Indicator of the setting menu
Description
Value to set
SET5
SERVICE MENU
ON/OFF
SET6
RESTORE SETTINGS
YES/NO
SET71)
TIME EXTENSION
ON/OFF
1) Selected models only
You can set the settings menu only when the appliance is off.
Activate the Settings menu:
1. If necessary, deactivate the appliance .
2. Touch and hold for three seconds.
The display shows "SET1" and "1" flashes.
/
to set the setting.
3. Touch
.
4. Touch
/
to change the value of the setting.
5. Touch
.
6. Touch
Automatic switch-off
For safety reasons the appliance deactivates automatically after some time:
• if an oven function operates.
• if you do not change the oven temperature.
Oven temperature
Switch-off time
30 °C -120 °C
12.5 h.
120 °C - 200 °C
8.5 h.
200 °C -230 °C
5.5 h.
After an automatic switch-off, touch a sensor field to operate the appliance again.
The Automatic switch-off works with all oven functions, apart from Slow Cook, Core temperature sensor, Duration, End, Time delay.
Brightness of the display
There are two modes of display brightness:
• Night brightness - when the appliance is deactivated, the brightness of the display is
lower between 10 PM and 6 AM.
• Day brightness:
– When the appliance is activated.
– If you touch a sensor fields during the night brightness (apart from ON / OFF), the display goes back to the day brightness mode for the next 10 seconds.
– If the appliance is deactivated and you set the Minute Minder. When the Minute
Minder function ends, the display goes back to the night brightness.
Care and cleaning
23
Cooling fan
When the appliance operates, the cooling fan activates automatically to keep the surfaces
of the appliance cool. If you deactivate the appliance, the cooling fan can continue to operate until the appliance cools down.
CARE AND CLEANING
WARNING!
Refer to "Safety information" chapter.
Notes on cleaning:
• Clean the front of the appliance with a soft cloth with warm water and cleaning agent.
• To clean metal surfaces use a usual cleaning agent.
• Clean the appliance interior after each use. Then you can remove dirt more easily and it
does not burn on.
• Clean stubborn dirt with a special oven cleaner.
• Clean all accessories (with a soft cloth with warm water and cleaning agent) after each
use and let them dry.
• If you have nonstick accessories, do not clean them using an aggressive agents, sharp
edged objects or dishwasher. It can cause a damage to the nonstick coating.
Steam cleaning
1.
2.
3.
4.
5.
Remove the worst of the dirt manually.
Put approximately 250 ml of water and 3 tablespoons of vinegar directly into the
steam generator.
Set the Steam cleaning function. Refer to "Oven functions".
The display shows the duration (15 minutes) and the default temperature. Touch OK to
start the cleaning.
An acoustic signal sounds when the steam cleaning is completed. Touch a sensor field
to stop the signal.
Clean the appliance with soft cloth. Remove the water from the steam generator with
the sponge and rub it dry.
Keep the door open for approximately 1 hour to let the appliance dry fully.
You can use the End function to delay the start of the cleaning. Refer to "Setting the END".
Shelf support
You can remove the shelf support to clean the side walls.
24
Care and cleaning
Removing the shelf support
1.
Carefully pull the support up and out of
the front catch.
2.
Lightly move the support on the front
catch inwards.
3.
Pull the support out of the rear catch.
Installing the shelf support
Install the shelf support in the opposite sequence.
Steam generation system
CAUTION!
Dry the steam generator after each use. Remove the water with the sponge.
Remove the limescale with water and vinegar.
CAUTION!
Chemical de-scaling agents can cause damage to the enamel. Follow the instructions of the
manufacturer.
Care and cleaning
25
Cleaning the water drawer and the steam generator:
1. Put the water and vinegar mixture (approximately 250 ml) through the water drawer
into the steam generator. Wait for approximately 10 minutes.
2. Remove the water and vinegar with the sponge.
3. Put clean water (100 - 200 ml) into the water drawer to flush the steam generation
system.
4. Remove the water from the steam generator with the sponge and rub it dry.
5. Keep the door open to let the appliance dry fully.
Oven lamp
WARNING!
There is a risk of electrical shock.
The oven lamp and the lamp glass cover can be hot.
Before you change the oven lamp:
• Deactivate the appliance.
• Remove the fuses from the fuse box or deactivate the circuit breaker.
CAUTION!
Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp
glass cover and the cavity.
Replacing the top lamp:
1. Turn the lamp glass cover counterclockwise to remove it.
2. Remove the metal ring and clean the glass cover.
3. Replace the lamp with a suitable 300 °C heat-resistant lamp.
Use the same lamp type.
4. Attach the metal ring to the glass cover.
5. Install the glass cover.
Replacing the side lamp:
1. Remove the left shelf support.
2. Use a torx 20 screwdriver to remove the cover.
3. Remove and clean the metal frame and the seal.
4. Replace the lamp with a suitable 300 °C heat-resistant lamp.
Use the same oven lamp type.
5.
6.
Install the metal frame and the seal. Tighten the screws.
Install the left shelf support.
Door and glass panels
To clean the door, remove it.
26
Care and cleaning
CAUTION!
Be careful when you remove the door from the appliance. The door is heavy!
Removing the door
1. Open the door as far as it goes.
2. Fully press clamping levers (A) on the
two door hinges.
3. Close the door until the first position
(angle approximately 70°).
4. Hold of the door with one hand on each
side and pull it away from the at an up
angle.
A
A
To install the door follow the procedure in
reverse.
The number of glass panels if different for the different models.
CAUTION!
Put the door with the outer side down on a soft and level surface to prevent scratches.
Removing and cleaning the door glass panels
1. Remove the door.
2. Hold the door trim (B) on the top edge
of the door at the two sides and push
inwards to release the clip seal.
3. Pull the door trim to the front to remove it.
B
4.
5.
Hold the door glass panels on their top
edge one by one and pull them up out
of the guide
Clean the door glass panels.
To install panels follow the procedure in reverse. Install the smaller panel first, then the
larger.
What to do if…
27
WHAT TO DO IF…
WARNING!
Refer to "Safety information" chapter.
Problem
Possible cause
Solution
The appliance does not heat up. The appliance is deactivated.
Activate the appliance.
The appliance does not heat up. The time of day is not set.
Set the clock. Refer to "First
setting the time of day".
The appliance does not heat up. The necessary settings are not
set.
Make sure that the settings are
correct.
The appliance does not heat up. The automatic switch-off is ac- Refer to „Automatic switchtivated.
off“.
The appliance does not heat up. The fuse is released.
Make sure that the fuse is the
cause of the malfunction. If the
fuse releases again and again,
contact a qualified electrician
The oven lamp does not operate.
The oven lamp is defective.
Replace the oven lamp.
The display shows F102.
The door lock is defective.
• Close the door correctly
• Deactivate the appliance
with the house fuse or the
safety switch in the fuse box
and activate it again.
• If the display shows F102
again, contact the Service
Center.
The display shows an error code There is an electrical fault.
that is not in this list.
• Deactivate the appliance
with the house fuse or the
safety switch in the fuse box
and activate it again.
• If the display shows the error code again, contact the
Service Center.
If you cannot find a solution to the problem yourself, contact your dealer or the service
centre.
The necessary data for the service centre is on the rating plate. The rating plate is on the
front frame of the appliance cavity.
We recommend that you write the data here:
Model (MOD.)
Product number (PNC)
Serial number (S.N.)
.........................................
.........................................
.........................................
28
Environment concerns
ENVIRONMENT CONCERNS
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
Packaging material
The packaging material is environmentally-friendly and recyclable. Plastic parts are marked
with international abbreviations such as PE, PS, etc. Dispose of the packaging material in
the containers provided for this purpose at your local waste management facility.
29
30
31
www.aeg.com/shop
892938091-A-102012