Progress | PI1325XC | User manual | Progress PI1325XC User Manual

User Manual
Dishwasher
PI1325XC
2 Progress
CONTENTS
Safety information
Safety instructions
Product description
Control panel
Programmes
Settings
2
3
5
6
7
7
Before first use
Daily use
Hints and tips
Care and cleaning
Troubleshooting
Technical information
9
10
11
13
14
17
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for
future reference.
Children and vulnerable people safety
•
•
•
•
•
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
Do not let children play with the appliance.
Keep all detergents away from children.
Keep children and pets away from the appliance door when
it is open.
Cleaning and user maintenance shall not be made by
children without supervision.
General Safety
•
This appliance is intended to be used in household and
similar applications such as:
– farm houses; staff kitchen areas in shops, offices and
other working environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments.
Progress 3
•
•
•
•
•
•
•
•
•
•
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum)
must be between 0.5 (0.05) / 8 (0.8) bar (Mpa)
Obey the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
Put knives and cutlery with sharp points in the cutlery basket
with the points down or in a horizontal position.
Do not keep the appliance door open without supervision to
prevent to fall on it.
Before maintenance, deactivate the appliance and
disconnect the mains plug from the mains socket.
Do not use water spray and steam to clean the appliance.
The ventilation openings in the base (if applicable) must not
be obstructed by a carpet.
The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the appliance is installed
below and adjacent to safe structures.
Electrical connection
WARNING! Risk of fire and
electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by our
Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the E.E.C.
Directives.
• Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is
necessary to change the fuse in the
4 Progress
mains plug, use fuse: 13 amp ASTA (BS
1362).
Water connection
• Make sure not to cause damage to the
water hoses.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
• The water inlet hose has a safety valve
and a sheath with an inner mains cable.
• Do not drink and play with the water in
the appliance.
• Do not remove the dishes from the
appliance until the programme is
completed. There can be detergent on
the dishes.
• The appliance can release hot steam if
you open the door while a programme
operates.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Service
• Contact the Authorised Service Centre
to repair the appliance. We recommend
only the use of original spare parts.
• When you contact the Authorised
Service Centre, ensure that you have the
following information that is available on
the rating plate.
Model :
PNC :
Serial Number :
WARNING! Dangerous
voltage.
• If the water inlet hose is damaged,
immediately disconnect the mains plug
from the mains socket. Contact the
Authorised Service Centre to replace the
water inlet hose.
Use
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous.
Obey the safety instructions on the
detergent packaging.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
Progress 5
PRODUCT DESCRIPTION
1
2
11
10
1
2
3
4
5
6
Upper spray arm
Lower spray arm
Filters
Rating plate
Salt container
Air vent
9
8 7
6
5
4
7
8
9
10
11
Rinse aid dispenser
Detergent dispenser
Cutlery basket
Lower basket
Upper basket
3
6 Progress
CONTROL PANEL
1
6
1
2
3
4
On/off indicator
Programme marker
Indicators
Delay button
2
3
5
4
5 Start button
6 Programme knob
Indicators
Indicator
Description
Washing phase. It comes on when the washing phase and the rinsing phases
operate.
Drying phase. It comes on when the drying phase operates.
End indicator.
Salt indicator. It is always off while the programme operates.
Rinse aid indicator. It is always off while the programme operates.
Progress 7
PROGRAMMES
Programme
2)
3)
Degree of
soil
Type of load
Programme
phases
Normal soil
Crockery and
cutlery
•
•
•
•
Normal soil
Crockery and
cutlery
•
•
•
•
Fresh soil
Crockery and
cutlery
• Wash 60 °C
or 65 °C
• Rinses
Consumption values
1)
Duration
(min)
Energy
(kWh)
Water
(l)
Prewash
Wash 50 °C
Rinses
Dry
195
1.039
11
Prewash
Wash 65 °C
Rinses
Dry
120 130
1.3 - 1.6
15 - 17
30
0.8
9
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of
dishes can change the values.
2) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery
with normal soil. (This is the standard programme for test institutes).
3) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
Information for test institutes
For all the necessary information for test
performance, send an email to:
Write down the product number (PNC) that
is on the rating plate.
info.test@dishwasher-production.com
SETTINGS
Programme selection mode and
user mode
When the appliance is in programme
selection mode it is possible to set a
programme and to enter the user mode.
In user mode, the following settings
can be changed:
• The level of the water softener according
to the water hardness.
These settings will be saved until you
change them again.
How to set the programme
selection mode
The appliance is in programme selection
mode when the on/off indicator comes on
and start indicator starts to flash.
When you activate the appliance, usually it
is in programme selection mode. However,
if this does not happen, you can set the
programme selection mode in the following
way:
Press and hold simultaneously Start and
Delay until the appliance is in programme
selection mode.
8 Progress
The water softener
The water softener removes minerals from
the water supply, which would have a
detrimental effect on the washing results
and on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness is
measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water in
your area. It is important to set the right
level of the water softener to assure good
washing results.
Water hardness
German degrees (°dH)
French degrees (°fH)
mmol/l
Clarke degrees
Water softener
level
47 - 50
84 - 90
8.4 - 9.0
58 - 63
10
43 - 46
76 - 83
7.6 - 8.3
53 - 57
9
37 - 42
65 - 75
6.5 - 7.5
46 - 52
8
29 - 36
51 - 64
5.1 - 6.4
36 - 45
7
23 - 28
40 - 50
4.0 - 5.0
28 - 35
6
19 - 22
33 - 39
3.3 - 3.9
23 - 27
5 1)
15 - 18
26 - 32
2.6 - 3.2
18 - 22
4
11 - 14
19 - 25
1.9 - 2.5
13 - 17
3
4 - 10
7 - 18
0.7 - 1.8
5 - 12
2
<4
<7
<0.7
<5
1 2)
1) Factory setting.
2) Do not use salt at this level.
If you use multi-tablets containing salt and
the hardness of your water is lower than
21dH, you can set the lowest water
softener level. It deactivates the salt refill
indicator.
If you use standard detergent or multitablets without salt, set the proper
water hardness level to keep the salt
refill indicator active.
How to set the water softener
level
The appliance must be in programme
selection mode.
1. Make sure that the programme marker
on the knob is aligned with the indicator
on/off .
2. To enter the user mode, press and hold
Delay. At the same time turn the knob
counterclockwise until the symbol of the
first programme is aligned with the
on/off indicator. Release Delay when
the indicators Start and on/off start to
flash.
3. Press Delay.
starts to flash.
• The indicator
• The indicators Start and on/off
continues to flash.
Progress 9
• The intermittent flashing of
refers to the current set level, e.g. 5
flashes + pause + 5 flashes = level 5.
4. Press Delay again and again to change
the setting. Each time you press Delay
the level number increases. After level
10 you will start again from level 1.
5. Turn knob to on/off position to confirm
the setting.
BEFORE FIRST USE
1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the baskets.
When you start a programme, the
appliance can take up to 5 minutes to
recharge the resin in the water softener. It
seems that the appliance is not working.
The washing phase starts only after this
procedure is completed. The procedure will
be repeated periodically.
The salt container
CAUTION! Only use salt
specifically designed for
dishwashers.
The salt is used to recharge the resin in the
water softener and to assure good washing
results in the daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container
(Only for the first time).
3. Fill the salt container with dishwasher
salt.
4. Remove the salt around the opening of
the salt container.
5. Turn the cap of the salt container
clockwise to close the salt container.
Water and salt can come out
from the salt container when
you fill it. Risk of corrosion. To
prevent it, after you fill the salt
container, start a programme.
10 Progress
How to fill the rinse aid
dispenser
1. Press the release button (D) to open the
lid (C).
2. Pour the rinse aid in the dispenser (A)
until the liquid reaches the fill level
'max'.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4. Close the lid. Make sure that the release
button locks into position.
B
A
M AX
4
1
3 2
+
-
C
D
You can turn the selector of the
released quantity (B) between
position 1 (lowest quantity) and
position 4 or 6 (highest quantity).
CAUTION! Only use rinse aid
specifically designed for
dishwashers.
DAILY USE
1. Open the water tap.
2. Turn the knob until the symbol of the
programme you want to set is aligned
with the on/off indicator. Set the correct
programme for the type of load and the
degree of soil.
• If the salt indicators is on, fill the salt
container.
• If the rinse aid indicator is on, fill the
rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Start the programme.
Using the detergent
A
30
B
1. Press the release button (B) to open the
lid (C).
2. Put the detergent, in powder or tablets,
in the compartment (A).
3. If the programme has a prewash phase,
put a small quantity of detergent in the
compartment (D).
4. Close the lid. Make sure that the release
button locks into position.
Using the multi-tablets
When you use tablets, that contain salt and
rinse aid, do not fill the salt container and
the rinse aid dispenser.
1. Adjust the water softener to the lowest
level.
2. Set the rinse aid dispenser to the lowest
position.
D
20
C
Progress 11
Setting and starting a
programme
Starting a programme
1. Open the water tap.
2. Close the appliance door.
3. Turn the knob until the symbol of a
programme you want to set is aligned
with the on/off indicator.
• On/off indicator comes on.
• Start indicator starts to flash.
4. Press Start.
• The programme starts .
• On/off indicator and start indicator
are on.
Starting a programme with
delay start
1. Set the programme.
2. Press Delay to delay the start of the
programme of 3 hours.
The delay indicator comes on.
3. Press Start.
Start indicator comes on.
When the countdown is completed, the
programme starts.
Opening the door while the
appliance operates
the energy consumption and the
programme duration. When you close the
door, the appliance continues from the
point of interruption.
Cancelling the delay start while
the countdown operates
1. Press and hold Start and Delay until
the start indicator starts to flash.
2. Press Start to start the programme.
Cancelling the programme
Press and hold Start and Delay until the
start indicator starts to flash.
Make sure that there is detergent in the
detergent dispenser before you start a new
programme.
End of the programme
When the programme is completed the
indicator is on. If you do not deactivate the
appliance within 5 minutes all indicators
goes off. This helps to decrease energy
consumption.
1. To deactivate the appliance, turn the
knob until the programme marker is
aligned with the on/off indicator.
2. Close the water tap.
If you open the door while a programme is
running, the appliance stops. It may affect
HINTS AND TIPS
General
The following hints will ensure optimal
cleaning and drying results in daily use and
also help to protect the environment.
• Remove larger residues of food from the
dishes into the waste bin.
• Do not pre-rinse dishes by hand. When
needed, use the prewash programme (if
available) or select a programme with a
prewash phase.
• Always use the whole space of the
baskets.
• When loading the appliance, make sure
that the dishes can be completely
reached and washed by the water
released from the spray arm nozzles.
Make sure that items do not touch or
cover each other.
• You can use dishwasher detergent, rinse
aid and salt separately or you can use
the multi-tablets (e.g. ''3in1'', ''4in1'',
''All in 1''). Follow the instructions written
on the packaging.
• Select the programme according to the
type of load and degree of soil. With the
ECO programme you have the most
12 Progress
efficient use of water and energy
consumption for crockery and cutlery
with normal soil.
Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause
damage to the appliance.
• Multi-tablets are usually suitable in areas
with a water hardness up to 21 °dH. In
areas exceeding this limit, rinse aid and
salt must be used in addition to the
multi-tablets. However, in areas with
hard and very hard water we
recommend to use solo-detergent
(powder, gel, tablets without additional
functions), rinse aid and salt separately
for optimal cleaning and drying results.
• If you use multi-tablets you can select
the Multitab option (if available). This
option increases the cleaning and drying
results with the use of multi-tablets.
• Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware, we
recommend that you use the tablets with
long programmes.
• Do not use more than the correct
quantity of detergent. Refer to the
instructions on the detergent packaging.
What to do if you want to stop
using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according to
the water hardness in your area.
5. Adjust the released quantity of rinse aid.
Loading the baskets
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made
of wood, horn, aluminium, pewter and
copper.
• Do not put in the appliance items that
can absorb water (sponges, household
cloths).
• Remove larger residues of food from the
dishes into the waste bin.
• Make soft the remaining burned food on
the items.
• Put hollow items (cups, glasses and
pans) with the opening down.
• Make sure that glasses do not touch
other glasses.
• Put cutlery and small items in the cutlery
basket.
• Put light items in the upper basket.
Make sure that the items do not move.
• Make sure that the spray arms can
move freely before you start a
programme.
Before starting a programme
Make sure that:
• The filters are clean and correctly
installed.
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is dishwasher salt and rinse aid
(unless you use multi- tablets).
• The position of the items in the baskets
is correct.
• The programme is applicable for the
type of load and for the degree of soil.
• The correct quantity of detergent is
used.
Unloading the baskets
1. Let the tableware cool down before you
remove it from the appliance. Hot items
can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
Progress 13
At the end of the programme
water can still remain on the
sides and on the door of the
appliance.
CARE AND CLEANING
WARNING! Before
maintenance, deactivate the
appliance and disconnect the
mains plug from the main
socket.
Dirty filters and clogged spray
arms decrease the washing
results. Make a check regularly
and, if necessary, clean them.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
Cleaning the filters
The filter system is made of 3 parts.
C
4. Wash the filters.
B
A
1. Turn the filter (B) counterclockwise and
remove it.
5. Make sure that there are no residues of
food or soil in or around the edge of the
sump.
6. Put back in place the flat filter (A). Make
sure that it is correctly positioned under
the 2 guides.
14 Progress
Cleaning the spray arms
Do not remove the spray arms. If the holes
in the spray arms are clogged, remove
remaining parts of soil with a thin pointed
object.
External cleaning
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A).
Turn it clockwise until it locks.
CAUTION! An incorrect position
of the filters can cause bad
washing results and damage to
the appliance.
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive
cleaning pads or solvents.
Internal cleaning
• Carefully clean the appliance, including
the rubber gasket of the door, with a soft
damp cloth.
• If you regularly use short duration
programmes, these can leave deposits
of grease and limescale inside the
appliance. To prevent this, we
recommend to run long duration
programmes at least 2 times per month.
• To maintain the performance of your
appliance at its best, we recommend to
use monthly a specific cleaning product
for dishwashers. Follow carefully the
instructions on the packaging of the
product.
TROUBLESHOOTING
If the appliance does not start or it stops
during operation, before you contact an
Authorised Service Centre, check if you can
solve the problem by yourself with the help
of the information in the table.
WARNING! Repairs not
properly done may result in
serious risk to the safety of the
user. Any repairs must be
performed by qualified
personnel.
With some problems the end indicator
flashes intermittently indicating a
malfunction.
The majority of problems that can
occur can be solved without the need
to contact an Authorised Service
Centre.
Progress 15
Problem and alarm code
Possible cause and solution
You cannot activate the appliance.
• Make sure that the mains plug is connected to
the mains socket.
• Make sure that there is no damaged fuse in the
fuse box.
The programme does not start.
• Make sure that the appliance door is closed.
• Press Start.
• If the delay start is set, cancel the setting or wait
for the end of the countdown.
• The appliance has started the procedure to recharge the resin inside the water softener. The
duration of the procedure is approximately 5 minutes.
The appliance does not fill with water.
• The end indicator flashes 1 time intermittently.
• The Start indicator flashes continuously.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply
is not too low. For this information, contact your
local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not
clogged.
• Make sure that the inlet hose has no kinks or
bends.
The appliance does not drain the water.
• The end indicator flashes 2 times intermittently.
• The Start indicator flashes continuously.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or
bends.
The anti-flood device is on.
• The end indicator flashes 3 times intermittently.
• The Start indicator flashes continuously.
• Close the water tap and contact an Authorised
Service Centre.
The appliance stops and starts more
times during operation.
• It is normal. It provides optimal cleaning results
and energy savings.
The program lasts too long.
• If the delayed start option is set, cancel the delay
setting or wait for the end of the countdown.
Small leak from the appliance door.
• The appliance is not level. Loosen or tighten the
adjustable feet (if applicable).
• The appliance door is not centred on the tub. Adjust the rear foot (if applicable).
The appliance door is difficult to close.
• The appliance is not level. Loosen or tighten the
adjustable feet (if applicable).
• Parts of the tableware are protruding from the
baskets.
16 Progress
Problem and alarm code
Possible cause and solution
Rattling/knocking sounds from inside
the appliance.
• The tableware is not properly arranged in the
baskets. Refer to basket loading leaflet.
• Make sure that the spray arms can rotate freely.
The appliance trips the circuit-beaker.
• The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket
amperage and the capacity of the meter or turn
off one of the appliances in use.
• Internal electrical fault of the appliance. Contact
an Authorised Service Centre.
Refer to "Before first use",
"Daily use", or "Hints and
tips" for other possible causes.
For alarm codes not described in the table,
contact an Authorised Service Centre.
Once you have checked the appliance,
press Start. If the problem occurs again,
contact an Authorised Service Centre.
The washing and drying results are not satisfactory
Problem
Possible cause and solution
Poor washing results.
• Refer to "Daily use", "Hints and tips" and basket loading leaflet.
• Use more intensive washing programs.
Poor drying results.
• Tableware has been left for too long inside a closed appliance.
• There is no rinse aid or the dosage of rinse aid is not
enough. Set the rinse aid dispenser to a higher level.
• Plastic items may need to be towel dried.
There are whitish streaks or
bluish layers on glasses and
dishes.
• The release quantity of rinse aid is too much. Adjust the
rinse aid selector to a lower position.
• The quantity of detergent is too much.
There are stains and dry water
drops on glasses and dishes.
• The released quantity of rinse aid is not sufficient. Adjust
the rinse aid selector to a higher position.
• The quality of the rinse aid can be the cause.
The dishes are wet.
• The programme does not have a drying phase or has a
drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
The interior of the appliance is
wet.
• This is not a defect of the appliance. it is caused by the
humidity in the air that condenses on the walls.
Progress 17
Problem
Possible cause and solution
Unusual foam during washing.
• Use the detergent for dishwashers only.
• There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre.
Traces of rust on cutlery.
• There is too much salt in the water used for washing. Refer to "The water softener".
• Silver and stainless steel cutlery were placed together.
Avoid to put silver and stainless steel items close together.
There are residues of detergent
in the dispenser at the end of
the program.
• The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
• Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged.
• Make sure that items in the baskets do not impede the lid
of the detergent dispenser from opening.
Odours inside the appliance.
• Refer to "Internal cleaning".
Limescale deposits on the tableware, on the tub and on the
inside of the door.
• Refer to "The water softener".
Dull, discoloured or chipped tableware.
• Make sure that only dishwasher-safe items are washed in
the appliance.
• Load and unload the basket carefully. Refer to basket
loading leaflet.
• Place delicate items in the upper basket.
Refer to "Before first use",
"Daily use" or "Hints and
tips" for other possible causes.
TECHNICAL INFORMATION
Dimensions
Width / height / depth (mm)
596 / 818 - 898 / 575
Electrical connection 1)
Voltage (V)
220 - 240
Frequency (Hz)
50
Water supply pressure
Min. / max. bar (MPa)
0.5 (0.05) / 8 (0.8)
Water supply
Cold water or hot water 2)
max 60 °C
Capacity
Place settings
13
Power consumption
Left-on mode (W)
0.50
18 Progress
Power consumption
Off-mode (W)
0.50
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water
supply to decrease energy consumption.
ENVIRONMENT CONCERNS
dispose appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it. Help protect the environment
and human health and to recycle waste of
electrical and electronic appliances. Do not
*
Progress 19
www.progress-hausgeraete.de
100010120-A-132015
Download PDF

advertising