Aeg-Electrolux F44080ID User Manual

Aeg-Electrolux F44080ID User Manual
FAVORIT 44080 i
User manual
Dear Customer
Thank you for choosing one of our highquality products.
With this appliance you will experience the perfect combination of functional
design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best per
formance and control indeed we are setting the highest standards of excel
In addition to this you find environmental and energy saving aspects as an inte
gral part of our products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfect
ly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a
safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips
Environmental information
Operating Instructions
Diagram of appliance
Control panel
Prior to using for the first time
Setting the water softener
Adding special salt
Filling up with rinse aid
In daily use
Loading cutlery and dishes
Adjusting the height of the upper basket
Adding detergent
Using 3in1 detergents
Selecting the dishwashing cycle (Cycle Table)
Starting a dishwashing cycle
Setting the Delay Timer
Switching off the dishwasher
Care and cleaning
What to do if…
Remedying small malfunctions
If the dishwashing results are not satisfactory
Technical data
Notes for Test Institutes
Installation and connection instructions
Safety information for the installation
Installing the dishwasher
Connecting the dishwasher
Guarantee/Customer Service
Operating Instructions
Operating Instructions
1 Safety
Prior to using for the first time
• Follow the ”Instructions for installation and connection”.
Correct use
• The dishwasher is only intended for washing domestic dishes.
• Additions or modifications to the dishwasher are not permitted.
• Use only special salt, detergent and rinse aid suitable for domestic dishwash
• Do not put any solvents in the dishwasher. This could cause an explosion.
Child safety
• Keep packaging away from children. There is a risk of suffocation.
• Children often do not recognise the hazards associated with electrical appli
ances. Don’t allow children to use the dishwasher unsupervised.
• Make sure that children and pets don’t climb into the dishwasher. Could en
danger life!
• Dishwasher detergents can cause chemical burns to the eyes, mouth and
throat. Could endanger life! Comply with the safety instructions of the dish
washer detergent manufacturer.
• The water in the dishwasher is not for drinking. Risk of chemical burns.
General safety
• Repairs to the dishwasher are only to be carried out by qualified service engi
• When the dishwasher is not being used, switch it off and shut off the water
• Never unplug the appliance by pulling on the cable. Always pull the plug.
• Ensure that the door of the dishwasher is always closed when it is not being
loaded or unloaded. In this way you will avoid anybody tripping over the open
door and hurting themselves.
• Never sit or stand on the open door.
• If the dishwasher is located in a room where there may be a frost, remove the
connection hose from the tap after each use of the dishwasher.
Diagram of appliance
Diagram of appliance
Upper basket spray arm
and floor spray arm
Water hardness
for special salt
for detergent
for rinse aid
Rating plate
Control panel
Control panel
ON/OFF button
The ON/OFF button is used to turn the dishwasher on and off.
End of cycle indicator
Programme buttons
Programme progress
Function buttons
delay timer
3 in1 function
The Programme buttons are used to select the desired dishwashing cycle.
Control panel
Function buttons: In addition to the preset dishwashing cycle, the following
functions can also be set using these buttons:
Function button 1
Set the water softener
Function button 2
Activates/deactivates rinse aid inflow when 3in1 on
Function button 3
not programmed The rinse aid inflow is only affected, if the 3in1 function is selected.
Programme progress display: The current stage of the programme is always
shown in the programme progress display.
The control indicators have the following meanings:
Refill with special salt
Refill with rinse aid
1) These control indicators are never illuminated while a dishwashing cycle is running.
Prior to using for the first time
Prior to using for the first time
If you wish to use 3 in 1 detergent:
– First read the section “Using 3in1 detergents”.
– Do not fill up with special salt or rinse aid.
If you do not use 3in1 detergent, before using for the first time
1. Set the water softener
2. Fill up with special salt for water softeners
3. Fill up with rinse aid
Setting the water softener
The water softener must be set manually and electronically:
To avoid scale deposits on the dishes and in the dishwasher, the dishes must be
washed with soft water, i.e. water with a low lime content. The water softener
must be set according to the table to the water hardness in the area where you
live. Your local water company will be able to give you information about the
water hardness in your area.
The dishwasher must be switched off.
Setting manually:
1. Open the dishwasher door.
2. Remove the lower basket from the
3. Turn water hardness dial on the left wall of
the dishwasher interior to 1 or 2 (see table).
Setting electronically:
1. Press the ON/OFF button.
If the only LED indicator illuminated is one
that belongs to a programme button, this
means that this dishwashing cycle has been activated. The dishwashing cycle
must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected light up.
2. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
Prior to using for the first time
3. Press function button 1.
The LED indicator for function button 1 will flash.
The LED indicator for the end of the dishwashing cycle will flash simultaneously:
– The number of times that the LED indicator for the end of the dishwashing cy
cle flashes corresponds to the hardness setting.
– This sequence of flashes is repeated several times, with a 3 second pause in
4. Pressing function button 1 increases the hardness setting by 1 degree.
(Exception: hardness setting 1 follows hardness setting 10).
5. When the hardness setting is correct, press the ON/OFF button.
The hardness setting is now saved.
If the water softener is set electronically to “1”, this switches off the control in
dicator for special salt.
Water hardness
Adjusting the hardness setting
Number of
1,9 2,5
0,7 1,8
no salt
in mmol/l
51 70
43 50
37 42
29 36
23 28
9,0 12,5
7,6 8,9
6,5 7,5
5,1 6,4
4,0 5,0
19 22
15 18
3,3 3,9
2,6 3,2
11 14
4 10
in °d
below 4
below 0.7
1) (°d) German degree, measure of the hardness of water
2) [mmol/l] millimol per litre, international unit for water hardness
3) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting
Prior to using for the first time
Adding special salt
To decalcify the water softener, it must be filled up with special salt. Use only
special salt suitable for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with special salt:
– Before using the dishwasher for the first time.
– When the control indicator for special salt is illuminated on the control panel.
Open the door and remove the lower
Screw open the lid on the salt dispenser by
turning it anticlockwise.
Only when using the dishwasher for the
first time:
Fill the salt dispenser with water.
Place the funnel (supplied) over the dis
penser opening.
Fill the dispenser with special salt; the ca
pacity of the dispenser is approx. 1.01.5
kg, depending on the size of the grains. Do
not overfill the dispenser.
If water overflows when filling up with special salt, this is completely harmless.
5. Clean away any salt remnants from the dispenser opening.
6. Screw the lid back on in a clockwise direction.
7. Run a dishwashing cycle after filling the salt dispenser with special salt.
This will wash away salt water and salt crystals that have been spilt.
Depending on the size of the salt grains, it can take several hours for the salt to
dissolve in the water and for the control indicator for special salt to go out.
Prior to using for the first time
Filling up with rinse aid
With rinse aid the rinsing water drains away better and so you get smearfree,
gleaming dishes and clear glasses.
If you do not use 3in1 detergent, fill up with rinse aid:
– Before using the dishwasher for the first time.
– When the control indicator for rinse aid is illuminated on the control panel.
Use only special rinse aid for dishwashers
and no other liquid detergents.
1. Open the door.
The rinse aid compartment is located on
the inside of the dishwasher door.
2. Press the release button on the rinse aid
3. Open the cover.
4. Pour rinse aid in slowly right up to the bro
ken “max” line;
this corresponds to a volume of approx.
140 ml when full.
5. Press the lid shut until it clicks into place.
6. Wipe up any spilt rinse aid with a cloth.
Otherwise there will be too much foam
when rinsing.
Prior to using for the first time
Setting the amount of rinse aid required
Only change the amount dispensed, if smears, milky spots (reduce the amount)
or dried on water spots (increase the amount) can be seen on glasses and dishes.
(See section “If dishwashing results are not satisfactory”.) The dosage can be set
from 16. The dosage is preset to “4” in the factory.
Open the dishwasher door.
Press the release button on the rinse aid
Open the cover.
Set the dosage level.
Press the lid shut until it clicks into place.
If rinse aid has leaked out, wipe it away
with a cloth.
Prior to using for the first time
Activating rinse aid inflow when 3in1 function is selected
If the 3in1 function is not selected, the rinse aid inflow is always activated.
If the 3in1 function is selected due to the use of 3in1 detergent, the rinse aid in
flow is deactivated. If the dishes then do not dry sufficiently, you should reacti
vate the rinse aid inflow (see also section “Using 3in1 detergents”).
1. Press the ON/OFF button.
If the only LED indicator illuminated is one that belongs to a programme button,
this means that this dishwashing cycle has been activated. The dishwashing cy
cle must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected light up.
2. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 2.
The LED indicator for function button 2 will flash.
The indicator for the end of the dishwashing cycle will display the current set
Indicator for the end of the cycle is lit:
Rinse aid inflow activated when 3in1 on
Indicator for the end of the cycle is not lit:
Rinse aid inflow deactivated when 3in1 on
(factory setting)
4. Pressing function button 2 activates and deactivates the rinse aid dispensing
5. When the rinse aid inflow setting is correct, press the ON/OFF button.
The setting for the rinse aid inflow is now saved.
In daily use
In daily use
Loading cutlery and dishes
Sponges, cleaning cloths and any other objects that can absorb water must not
be washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to
retain water droplets. These dishes and pans therefore do not dry as well as
those made of china and stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable:
are of limited suitability:
• Only wash stoneware in the dishwasher if it is spe
• Cutlery with wooden, horn, china or
cifically marked by the manufacturer as being dish
mother of pearl handles
• Plastic items that are not heat re
• Glazed patterns may fade if washed very frequently
in the dishwasher.
• Older cutlery with cement
• Silver and aluminium parts have a tendency to dis
that is sensitive to temperature
colour during washing. Food remains, e.g. egg white,
• Dishes or cutlery with glued parts
egg yolk and mustard often cause discoloration and
• Pewter or copper items
staining on silver. Therefore always clean food resi
• Lead crystal glass
dues from silver immediately, if it is not to be
• Steel items that rust
washed straight after use.
• Wooden boards/platters
• Glass can become dull after a large number of wash
• Items made from synthetic materials
• Before loading the dishes, you should:
– Remove the worst of the food residues.
– Soak pans with burnton food residues.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation of the spray arms.
– Load bowls, cups, glasses, pans, etc. with the opening downwards so that
water cannot collect in them
– Dishes and items of cutlery must not lie inside one another or cover one an
– To avoid damage to glasses, they must not touch one another
– Don’t put small items (e.g. lids) in the baskets for the dishes, but in the cut
lery basket, so that they can’t fall through the holes.
In daily use
Loading cutlery
Warning: Sharp knives and other items of cutlery with sharp edges must be laid
in the cutlery rack or in the upper basket to avoid the risk of injury.
To ensure that all items of cutlery in the cutlery basket can be reached by the
water, you should:
1.Place the grid insert on the cutlery 2.Place forks and spoons in the cutlery
basket's grid insert with their han
dles pointing downwards.
For larger utensils, such as whisks, leave off one half of the cutlery grid.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes and
pans in the lower basket.
(Max. diameter for plates 29 cm).
In daily use
To make it easier to load larger dishes, the
two plate rests on the right in the lower
basket can be folded down.
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long,
sharp cutlery in the upper basket.
• Arrange items of crockery on and under
the folding cup racks so that they are
offset from each other and water can
reach all items.
• The cup racks can be folded up out of the
way for tall crockery items.
• Lay or hang wine and brandy glasses in
the slots in the cup racks.
In daily use
Adjusting the height of the upper basket
Maximum height of dishes in the
Upper basket
Lower basket
with upper basket raised
22 cm
30 cm
with upper basket lowered
24 cm
29 cm
The height of the baskets can also be adjusted when they are loaded.
Raising / Lowering the upper basket
1. Pull out the upper basket completely.
2. Holding the upper basket by the handle,
raise it as far as it will go and then lower it
The upper basket will latch into the lower
or the upper position.
Adding detergent
Detergents remove the dirt from dishes and
The detergent must be added before the
cycle starts.
Only use detergent intended for domestic
The detergent compartment is located on
the inside of the door.
1. If the lid is closed:
Press the release button.
The lid will spring open.
In daily use
2. Place the detergent in the detergent dis
penser. The markings indicate the dosing
levels for powder detergents: “20/30” cor
responds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions
with regard to dosing and storage.
3. Close the lid and press until it locks into
In the case of very heavily soiled dishes, fill
the adjoining compartment (1) with addi
tional detergent. This detergent comes into
use during the prewash cycle.
Concentrated detergents
Today’s detergents for dishwashers are almost exclusively lowalkaline concen
trated detergents with natural enzymes in tablet or powder form.
Using 50°C dishwashing cycles in conjunction with these concentrated deter
gents reduces pollution and is good for your dishes, as these dishwashing cycles
are specially matched to the dirtdissolving properties of the enzymes in con
centrated detergents. It is for this reason that using 50 °C dishwashing cycles in
conjunction with concentrated detergents can achieve the same cleaning results
that can otherwise only be achieved using 65 °C cycles.
Detergent tablets
Detergent tablets from different manufacturers dissolve at different rates. For
this reason, some detergent tablets do not attain their full cleaning power dur
ing short cycles. Therefore please use dishwashing cycles with prewash when
using detergent tablets.
Using 3in1 detergents
These products are detergents with a combined cleaning, rinsing and salt func
When the 3in1 function is activated,
– the addition of special salt and rinse aid from the respective dispenser is pre
– If the salt and rinse aid dispensers are empty, this is not indicated.
– The dishwashing cycles can be up to 30 minutes longer.
In daily use
If you want to use 3in1 detergents, check whether these detergents are suitable
for your water hardness. (Follow manufacturer’s instructions!)
If your water hardness is higher than that recommended by the manufacturer
but you would nevertheless like to use 3in1 detergent, proceed as follows:
• With the 3in1 function selected, set the water softener one hardness setting
lower than when rinsing without 3in1 detergent.
• Fill up the dispenser (if this is empty) with special salt.
The dishwasher remembers the two different settings of the degree of hardness
for rinsing with and without 3in1 function.
If you want to use 3in1 products
1. Press the ON/OFF button.
2. Press the 3 IN 1 button.
The button indicator lights up: 3in1 function is selected.
Before the start of the dishwashing cycle put 3in1 detergent in the detergent
As the rinse aid inflow is automatically switched off when the 3in1 function is
activated, it may come about because of the different quality standards in the
3in1 detergent, that the dishes do not dry sufficiently.
If this happens, proceed as follows (see section “Adding rinse aid”):
• Fill up the dispenser (if this is empty) with rinse aid.
• Set rinse aid dosage to “2” mechanically.
• Activate rinse aid inflow.
If you do not want to use 3in1 products any more
If you want to stop using 3in1 products, please do the following:
• Deactivate the 3in1 function.
• Fill up the dispensers for salt and rinse aid again.
• Switch the water softener to the highest setting and perform up to three nor
mal cycles without loading any dishes.
• Then set the water softener to the water hardness in your area.
If you want to use 4in1 products
When using "4 in 1" detergents that integrate also anti glass corrosion agent
into "3 in 1" formula, please follow the same indication as given for "3 in 1" de
In daily use
Selecting the dishwashing cycle (Cycle Table)
Dinner service and
cookware, tempera
normally soiled
Water (litres)
12 24
90 110
22 24
heavily soiled,
driedon food remains,
in particular protein
and starch
14 16
Dinner service and
1,00 1,50 Energy (kWh)
CARE 70°4)
1,80 2,00
0,95 1,05
just used, lightly to nor
mally soiled
Length (minutes)
Dishes, excluding
120 130
30 MIN
130 160
Final rinse
normally soiled,
driedon food remains
1 to 2x
Dinner service and
(50° 65°)2)
Type of
Main wash
Intermediate rinse
1) The consumption values were obtained under standardised conditions. They depend on how full the bas
kets for the dishes are. Variations are therefore possible in practice.
2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The
length of the cycle and water and energy consumption can vary greatly – depending upon the load and
how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically
adjusted to between 50°C and 65°C.
3) When using this cycle, only load the dishwasher half full.
4) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e.g. babies’ bottles,
plastic chopping boards or jam jars.
5) Test programme for Test Institutes
In daily use
Selecting a programme
When your dishes look like this, select:
an intensive programme.
a normal or energysaving programme.
a short programme (e.g. 30 minute pro
In daily use
Starting a dishwashing cycle
Check that the spray arms can turn freely.
Turn the water tap on fully.
Close the door.
Press the ON/OFF button.
Select the desired cycle.
The programme display lights up. The selected cycle will begin after approxi
mately 3 seconds.
Interrupting or aborting a dishwashing cycle
Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary.
Interrupting the dishwashing programme by opening the dishwasher door
Hot steam may escape when the door is opened. There is a risk of scalding.
1. Open the door carefully. The dishwashing cycle will stop.
2. Close the door. The cycle will continue.
Aborting the dishwashing cycle
1. Press function buttons 2 and 3 and keep them pressed.
The LED indicators of all the programme buttons that can be selected light up.
2. Release the function buttons. The dishwashing cycle has been cancelled.
3. If you want to start a new cycle, check whether there is any detergent in the dis
Turning off the dishwasher will only interrupt a selected dishwashing cycle, not
cancel it. The cycle will recommence after turning the dishwasher back on again.
Setting the Delay Timer
Using the delay timer you can delay the start of a dishwashing cycle for 3, 6 or 9
1. Press the ON/OFF button.
2. Press the Delay Timer button repeatedly until the indicator next to the number
of hours for which the start of the dishwashing cycle is to be delayed lights up,
e. g. 6h, if the cycle is to start in 6 hours.
3. Select dishwashing cycle.
The LED indicator for the programme selected and the indicator next to the
number of hours will light up.
The dishwashing cycle will start automatically following a countdown of the
hours set.
In daily use
To change the time delay:
As long as the cycle has not yet started, you can still change the setting by
pressing the DELAY TIMER button.
Cancelling the delay timer:
Press the DELAY TIMER button repeatedly until none of the three time displays is
lit. The selected dishwashing cycle will begin immediately.
To change a dishwashing cycle
As long as the cycle has not yet started, you can still change the dishwashing
cycle. First abort the dishwashing cycle, then reset the time delay, lastly select
the new dishwashing cycle.
Switching off the dishwasher
Do not switch off the dishwasher until the indicator for the end of the dish
washer cycle is illuminated in the cycle progress display.
1. Press the ON/OFF button. All display indicators will go out.
2. Turn off the water tap.
Carefully open the door. Hot steam may escape.
• Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about
15 minutes before removing them. You also get a better drying result.
• Dishes dry more quickly if you open the door for a moment after the cycle has
ended and then leave it slightly open.
Removing the dishes
It is normal for the inner door and the dispensers to be damp.
• Empty the lower basket first, then the upper basket. This way you avoid drip
ping water from the upper basket onto dishes in the lower basket.
Care and cleaning
Care and cleaning
Do not use furniture care products or aggressive cleaners.
• When necessary, clean the dishwasher’s controls with a soft cloth and clean
warm water.
• Occasionally check the internal dispensers, door seal and water inlet filter (if
fitted) for dirt and clean them, if necessary.
Cleaning the filters
The filters must be regularly checked and
cleaned. Dirty filters will spoil the wash re
1. Open the door and remove the lower basket.
2. Turn the handle about ¼ of a turn anticlock
wise (A) and remove the filter system (B).
3. Grasp the grip hole on the fine filter (1) and
remove it from the microfilter (2).
4. Clean all filters thoroughly under running
Care and cleaning
5. Remove the flat filter (3) from the base of
the washing compartment and clean both
surfaces thoroughly.
6. Reinsert the flat filter.
7. Place the fine filter in the microfilter and fit
the two together.
8. Insert the filter system in place and lock it by
turning the handle clockwise as far as it will
go. Ensure that the flat filter does not pro
trude above the base of the washing com
Under no circumstances may the dishwasher be used without its filters.
What to do if…
What to do if…
Remedying small malfunctions
Before you call the Customer Care Department, please check whether
– you cannot remedy the fault yourself with the help of the following fault ta
– whether it is caused by faulty, electrical connections and/or faulty water con
In these cases the engineer must make you liable for the costs of the Customer
Service intervention even during the warranty period.
If while the appliance is operating indicators on the control panel flash or are lit
up as described in the following table, please consult this to find out how to
remedy the fault.
After remedying the fault that is flashing in the first or second rhythm in the
programme progress display, press the button for the dishwashing cycle that
had already started. The cycle will continue.
In the case of other fault messages:
– Cancel the dishwashing cycle.
– Switch the appliance off and on again.
– Select dishwashing cycle.
If the fault is displayed again, please contact the Customer Care Department
and inform them of the fault message.
The programme indicator for the
selected dishwashing cycle is
the indicator for the end of the
dishwashing cycle is flashing in
rhythm 1 short light signal with
approx. 3 second pause inbe
(Problems with water inlet)
Possible cause
The tap is blocked or furred
with limescale.
Clean tap.
The tap is turned off.
Turn the tap on.
The filter (where present) in the
Clean the filter in the
threaded hose fitting on the tap
threaded hose fitting.
is blocked.
Filters in the base of the wash
ing compartment are blocked.
Cancel the dishwashing cy
cle (see chapter: Starting a
dishwashing cycle),
clean filters (see chapter:
Cleaning the filters),
then start the dishwashing
cycle again.
Water inflow hose has not been
Check hose installation.
correctly positioned.
What to do if…
Possible cause
The programme indicator for the The sink outlet is blocked.
selected dishwashing cycle is
the indicator for the end of the Water drain hose has not been
dishwashing cycle is flashing in correctly positioned.
rhythm 2 short light signals one
after another.
Clean out sink outlet.
Check hose installation.
the indicator for the end of the
Turn off the tap and con
dishwashing cycle is flashing in The antiflood system has been
tact the Customer Care de
rhythm 3 short light signals one triggered.
after another.
The mains plug is not
plugged in.
The cycle is not starting.
Plug in mains plug.
A fuse in the house’s wiring sys
Replace fuse.
tem is defective.
For dishwasher models with a
delay start timer:
A start time has been selected.
If the dishes are to be
washed immediately, can
cel the delay start.
The dishwashing compartment
is made from rustfree stainless
steel. Rust spots in the dish
washing compartment are due
Only wash cutlery, dishes
Rust spots are visible in the dish to rust particles from external
and pans that are suitable
sources (rust particles from wa
washing compartment.
for dishwasher use.
ter pipes, pans, cutlery, etc.). Re
move such spots with a
commerciallyavailable stain
less steel cleaning product.
A whistling noise can be heard
when washing dishes.
The whistling is not a cause for
Decalcify appliance with
commercially available
agents for cleaning dish
If the noises can still be
heard after decalcifying the
machine, use a different
brand of detergent for
washing cutlery and dishes.
What to do if…
If the dishwashing results are not satisfactory
The dishes are still dirty.
• The wrong dishwashing cycle was selected.
• The dishes were loaded is such a way that the dishwashing water did not
reach all items. The baskets for the dishes must not be overloaded.
• Filters in the floor of the dishwasher are not clean or incorrectly inserted.
• Good quality detergent was not used, or too little was used.
• In the case of scale deposits on the dishes: The special salt dispenser is empty
or the water softening system has been incorrectly set.
• The drain hose is incorrectly positioned.
• If at the end of the dishwashing cycle there is still detergent left in the deter
gent dispenser, either the spray arm was jammed or the spray arm jets are
blocked with pollutants in the dishwashing water.
You have the option of removing the spray arms from their fixture for clean
ing (see section “Care and Cleaning”).
The dishes do not dry and are not shining.
• Poor quality rinse aid was used.
• The rinse aid dispenser is empty.
There are smears, streaks, milky spots or a shiny bluish coating on glasses
and dishes.
• Lower rinse aid dosage.
There are dried water drops on the glasses and dishes.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer's cus
tomer advice centre.
Glass corrosion
• Contact the detergent manufacturer's customer advice centre.
Packaging material
The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dis
pose of the packaging materials in the appropriate container at the community
waste disposal facilities.
Old appliance
The symbol
on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equip
ment. By ensuring this product is disposed of correctly, you will help prevent po
tential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you
purchased the product.
Warning! When your appliance has finished its working life, remove the plug
from the socket. Cut off the cable and plug and dispose of them.
Break the door lock so that the door no longer shuts. This prevents children from
trapping themselves inside and endangering their lives.
Technical data
12 place settings including serving dishes
Permitted water pressure:
0.11.0 MPa (= 10100 N/cm2 = 110 bar )
Electrical connection:
See the rating plate on the righthand side of the dishwasher’s in
terior door .
818 878 x 596 x 570 (H x W x D in mm)
Max. weight:
45 kg
Notes for Test Institutes
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the appliance
fully loaded and using the test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be carried out when the salt dis
penser in the water softener and the rinse aid dispenser have been filled with
salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).
Full load: 12 place settings including serving dishes
Amount of detergent re
5g + 25g (Type B)
Rinse aid setting:
4 (Type III)
Example loading arrangements:
Upper basket *)
*) If there are cup racks in place on the lefthand side or the cutlery tray is in place, remove them.
Lower basket with cutlery basket*)
Cutlery basket
*) If necessary, you can remove the cup racks on the lefthand side and/or the beer glass holder.
Installation and connection instructions
Installation and connection instructions
1 Safety information for the installation
• Only transport the dishwasher in an upright position, otherwise salt water
may run out.
• Before using the dishwasher for the first time, check for any damage caused in
transport. Do not under any circumstances connect an appliance that is dam
aged. In the case of damage, please contact your supplier.
• Never use the dishwasher if the mains cable, water inlet or drain hose are
damaged; or if the control panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.
• Always plug the mains plug into a correctly installed shockproof socket.
• Prior to using the appliance for the first time, ensure that the rated voltage
and type of supply on the rating plate match that of the supply where the ap
pliance is to be installed. The fuse rating is also to be found on the rating plate.
• Multiway plugs / connectors and extension cables must not be used. This
could constitute a fire hazard through overheating.
• The dishwasher’s cable must only be replaced by the Customer Care Depart
ment or a registered electrician.
• A water inlet hose with safety valve must only be replaced by the Customer
Care Department.
Installing the dishwasher
• The dishwasher must be installed on a firm floor and adjusted to ensure that it
is stable and level in all directions.
• To compensate for unevenness in the floor and to match the height of the ap
pliance to that of surrounding units, extend the threaded feet using a screw
• Adjust the rear foot of the appliance using a cordless screwdriver from the
front of the appliance (see installation template).
• The drain hose, inlet hose and mains cable must be laid so that they are able to
move freely within the plinth area, and so that they are not kinked or crushed
when the dishwasher is in position.
• The dishwasher must also be screwed tightly to the work surface or to the ad
joining units. This is essential to ensure the dishwasher does not tip up.
Connecting the dishwasher
Dishwashers that can be integrated
(see installation template supplied)
Using the installation template supplied split cupboard doors can be easily in
stalled and firmly fitted.
Connecting the dishwasher
Connecting to the water supply
• The dishwasher can be connected to cold and hot water supplies up to max.
• The dishwasher must not be connected to open hot water appliances or in
stantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure:
0,1 MPa ( = 1 bar = 10 N/cm2 )
Consult your plumber if the water pressure is
less than 0,1 MPa.
Highest permitted water pressure:
1 MPa ( = 10 bar = 100 N/cm2 )
If the water pressure is greater than
1 MPa, a pressure reduction valve must be used
(available from your dealer).
Connecting the inlet hose
The water inlet hose must not be kinked, crushed or entangled when it is being
Connect the threaded hose fitting (ISO 2281:2000) on the water inlet hose to a
tap with an external thread (¾ inch). The inlet hose is fitted with either a plastic
or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make sure that the tap is not drip
So that access to the tap in the kitchen is not restricted by the use of the dish
washer, we recommend installing an additional tap, or fitting a Tbranch to the
existing tap.
Connecting the dishwasher
WARNING! Dangerous voltage
(This does apply to dishwashers with safety
The electrical cable for the safety valve is in
the doublewalled water inlet hose and is
Therefore do not immerse the water inlet
hose or the safety valve in water.
Water drainage
The drain hose must not be kinked, crushed
or entangled.
• Connecting the drain hose:
maximum permitted height above the
bottom edge of the appliance: 60 cm.
Extension hoses
• Extension hoses are available from your
dealer or from our Customer Care Depart
ment. To ensure that the function of the
appliance is not impeded, the internal di
ameter of extension hoses must be 19 mm.
• The total length including extension hoses
must not exceed 4 metres.
permitted distance
Drain hose
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all commonly available sink outlet
types. The outer diameter of the sink outlet connection must be at least 15
• The drain hose must be fixed to the sink outlet connection using the hose
clamp supplied.
Connecting the dishwasher
Antiflood system
For protection from water damage, the dishwasher is equipped with a antiflood
In the event of a fault, the safety valve in the water inlet hose immediately in
terrupts the supply of water to the appliance.
Electrical connection
Details about the voltage, type of supply and the fuses required are to be found
on the rating plate. The rating plate is located on the righthand inner edge of
the dishwasher door.
To isolate the dishwasher from the mains, pull out the mains plug.
– Safety standards require the appliance to be earthed. The manufacturer ac
cepts no liability for failure to observe the above safety precautions.
– The plug must be accessible after the appliance has been installed.
Guarantee/Customer Service
Guarantee/Customer Service
Our appliances are produced with the greatest of care. However, a defect may still occur. Our
consumer services department will repair this upon request, either during or after the guarantee
period. The service life of the appliance will not, however, be reduced as a result.
This declaration of guarantee terms is based on European Union Directive 99/44/EC and the pro
visions of the Civil Code. The statutory rights that the consumer has under this legislation are
not affected by this declaration of guarantee terms.
This declaration does not affect the vendor's statutory warranty to the end user. The appliance is
guaranteed within the context of and in adherence with the following terms:
1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of charge
any defect that occurs within 24 months from the date the appliance is delivered to the first
end user.
These guarantee terms do not apply in the event of use for professional or equivalent purpos
2. Performing the guarantee means that the appliance is returned to the condition it was in be
fore the defect occurred. Defective parts are replaced or repaired. Parts replaced free of
charge become our property.
3. So as to avoid more severe damage, the defect must be brought to our attention immediately.
4. Applying the guarantee is subject to the consumer providing proof of purchase showing the
purchase and/or delivery date.
5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ce
ramic), synthetic materials and rubber, is the result of inappropriate use.
6. The guarantee cannot be called on for minor faults that do not affect the value or the overall
reliability of the appliance.
7. The statutory warranty does not apply when defects are caused by:
– a chemical or electrochemical reaction caused by water,
– abnormal environmental conditions in general,
– unsuitable operating conditions,
– contact with harsh substances.
8. The guarantee does not apply to defects due to transport which have occurred outside of our
responsibility. Nor will the guarantee cover those caused by inadequate installation or assem
bly, lack of maintenance or failure to respect the assembly instructions or directions for use.
9. Defects that result from repairs or measures carried out by people who are not qualified or
expert or defects that result from the addition of nonoriginal accessories or spare parts are
not covered by the guarantee.
10.Appliances that are easy to transport may be delivered or sent to the consumer services de
partment. Home repairs are only anticipated for bulky appliances or builtin appliances.
11.If the appliances are builtin, builtunder, fixed or suspended in such a way that removing
and replacing them in the place where they are fitted takes more than half an hour, the costs
that result therefrom will be charged for. Connected damage caused by these removal and re
placement operations will be the responsibility of the user.
Guarantee/Customer Service
12.If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if
the repair costs are considered disproportionate, in agreement with the consumer, the defec
tive appliance may be replaced with another appliance of the same value.
In this event, we reserve the right to ask for a financial contribution calculated according to
the length of time it has been used.
13.A repair under guarantee does not mean that the normal guarantee period will be extended
nor that a new guarantee period begins.
14.We give a twelve month guarantee for repairs, limited to the same defect.
15.Except in the event where liability is legally imposed, this declaration of guarantee terms ex
cludes any compensation for damage outside the appliance for which the consumer wishes to
assert his rights. In the event of legally admitted liability, compensation will not exceed the
purchase price paid for the appliance.
These guarantee terms are only valid for appliances purchased and used in Belgium. For export
ed appliances, the user must first make sure that they satisfy the technical conditions (e.g.: volt
age, frequency, installation instructions, type of gas, etc.) for the country concerned and that
they can withstand the local climatic and environmental conditions. For appliances purchased
abroad, the user must first ensure that they meet the qualifications required in Belgium. Non
essential or requested adjustments are not covered by the guarantee and are not possible in all
Our consumer services department is always at your disposal, even after the guarantee period
has expired.
Address for our consumer services department:
Electrolux Home Products Belgium
Consumer services
Bergensesteenweg 719
1502 Lembeek
Email: [email protected]
GrandDuché de Luxembourg
Consumer services
Rue de Bitbourg. 7
L1273 LuxembourgHamm
Email: [email protected]
00 352 42 4311
00 352 42 431360
Guarantee/Customer Service
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for
the period specified in the appliance guarantee or otherwise by law. If you move from one of these coun
tries to another of the countries listed below the appliance guarantee will move with you subject to the fol
lowing qualifications:
• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced
by production of a valid purchase document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in
your new country of residence for this particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred
to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used
within the home, i.e. is not used for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in force within your new country of
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
+32 2 363 04 44
Bergensesteenweg 719, 1502 Lembeek
Èeská republika
+420 2 61 12 61 12
Budìjovická 3, Praha 4, 140 21
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
+37 2 66 50 030
Mustamäe tee 24, 10621 Tallinn
+34 902 11 63 88
Carretera M300, Km. 29,900
Alcalá de Henares Madrid
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire
+30 23 10 56 19 70
4 Limnou Str., 54627 Thessaloniki
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
+353 1 40 90 753
Long Mile Road Dublin 12
+39 (0) 434 558500 Lino Zanussi, 26 33080 Porcia (PN)
+37 17 84 59 34
Kr. Barona iela 130/2, LV1012, Riga
+370 5 2780609
Ozo 10A, LT 08200 Vilnius
+352 42 431 301
Rue de Bitbourg, 7, L1273 Hamm
+36 1 252 1773
H1142 Budapest XIV,
Erzsébet királyné útja 87
Guarantee/Customer Service
+31 17 24 68 300
Vennootsweg 1, 2404 CG Alphen aan den Rijn
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
+43 18 66 400
Herziggasse 9, 1230 Wien
+48 22 43 47 300
ul. Kolejowa 5/7, Warszawa
+35 12 14 40 39 39
Quinta da Fonte Edificio Gonçalves Zarco Q 35
2774 518 Paço de Arcos
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671 RO
+41 62 88 99 111
Industriestrasse 10, CH5506 Mägenwil
+38 61 24 25 731
Electrolux Ljubljana d.o.o.
Gerbiceva 98, 1000 Ljubljana
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux Domáce spot
rebièe SK, Seberíniho 1, 821 03 Bratislava
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143,
S105 45 Stockholm
+90 21 22 93 10 25
Tarlabaþý caddesi no : 35 Taksim
+7 095 937 7837
129090 Ìîñêâà, Îëèìïèéñêèé
ïðîñïåêò, 16, ÁÖ „Îëèìïèê“
In the event of technical faults, please first check whether you can remedy the
problem yourself with the help of the operating instructions (section “What to
do if…”).
If you were not able to remedy the problem yourself, please contact the Cus
tomer Care Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers see rating plate)
– Type of fault
– Any error messages displayed by the ap
So that you have the necessary reference numbers from your appliance at hand,
we recommend that you write them in here:
Model description:
S No:
117 986 95/0-00-080307-01
Subject to change without notice
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF