Electrolux GA55LI101 User Manual

Add to my manuals
48 Pages

advertisement

Electrolux GA55LI101 User Manual | Manualzz
117986 48/0en
18-05-2007
9:24
Pagina 1
user manual
dishwasher
GA55LI101
117986 48/0en
18-05-2007
9:24
Pagina 2
We were thinking of you
when we made this product
117986 48/0en
18-05-2007
9:24
Pagina 3
welcome to the world of Electrolux electrolux 3
Welcome to the world of Electrolux
You’ve chosen a first class product from Electrolux, which
hopefully will provide you with lots of pleasure in the future.
Electrolux ambition is to offer a wide variety of quality products
that make your life more comfortable. You can look at some
examples on the cover in this manual. But now it’s time to study
this manual and start using and enjoying the benefits from your
new machine. We promise that it’ll make your life a little easier.
Good luck!
117986 48/0
117986 48/0en
18-05-2007
9:24
Pagina 4
4 electrolux contents
Contents
Safety information
5
Product description
7
Control panel
8
First use
11
Daily use
15
Washing programmes
28
Care and cleaning
29
Something not working
32
Technical data
35
Hints for test institutes
37
Installation
39
Environment concerns
43
Warranty/Point of Service
44
The following symbols are used in this manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips
Environmental information
117986 48/0en
18-05-2007
9:24
Pagina 5
safety information electrolux 5
Safety information
●
In the interest of your safety and to
ensure the correct use, before
installing and first using the
appliance, read this user manual
carefully, including its hints and
warnings. To avoid unnecessary
mistakes and accidents, it is
important to ensure that all people
using the appliance are thoroughly
familiar with its operation and
safety features. Save these
instructions and make sure that
they remain with the appliance if it
is moved or sold, so that everyone
using it through its life will be
properly informed on appliance use
and safety.
Correct use
● This dishwasher is only intended
for washing household utensils
suitable for machine washing.
● Do not put any solvents in the
dishwasher. This could cause an
explosion.
● Knives and other items with sharp
points must be loaded in the
cutlery basket with their points
down or placed in a horizontal
position in the upper basket.
● Only use products (detergent, salt
and rinse aid) suitable for
dishwashers.
● Avoid opening the door whilst the
appliance is in operation, hot
steam may escape.
● Do not take any dishes out of the
dishwasher before the end of the
dishwashing cycle.
●
●
After use, isolate the appliance
from the power supply and turn off
the water supply.
This product should be serviced
only by an authorised service
engineer, and only genuine spare
parts should be used.
Under no circumstances should
you attempt to repair the machine
yourself. Repairs carried out by
inexperienced persons will cause
injury or serious malfunctioning.
Contact your local Service Force
Centre. Always insist on genuine
spare parts.
General safety
Dishwasher detergents can cause
chemical burns to eyes, mouth and
throat. Could endanger life!
Comply with the safety instructions
of the dishwasher detergent
manufacturer.
● The water in your dishwasher is
not for drinking. Detergent
residues may still be present in
your machine.
● Ensure that the door of the
dishwasher is always closed when
it is not being loaded or unloaded.
In this way you will avoid anybody
tripping over the open door and
hurting themselves.
● Do not sit or stand on the open
door.
●
Child safety
This appliance is designed to be
operated by adults. Don’t allow
children to use the dishwasher
unsupervised.
●
117986 48/0en
18-05-2007
9:24
Pagina 6
6 electrolux safety information
●
●
●
Keep all packaging well away from
children. There is risk of
suffocation.
Keep all detergents in a safe place
out of children’s reach.
Keep children well away from the
dishwasher when the door is open.
Installation
Check your dishwasher for any
transport damage. Never connect
a damaged machine. If your
dishwasher is damaged contact
your supplier.
● All packaging must be removed
before use.
● Any electrical and plumbing work
required to install this appliance
must be carried out by a qualified
and competent person.
● For safety reasons it is dangerous
to alter the specifications or
attempt to modify this product in
any way.
● Never use the dishwasher if the
electrical supply cable and water
hoses are damaged; or if the
control panel, work top or plinth
area are damaged such that the
inside of the appliance is freely
accessible. Contact your local
Service Force centre, in order to
avoid hazard.
● All sides of the dishwasher must
never be drilled to prevent damage
to hydraulic and electric
components.
●
For electrical and water connection
carefully follow the instructions
given in specific paragraphs.
117986 48/0en
18-05-2007
9:24
Pagina 7
product description electrolux 7
Product description
1
2
3
4
5
6
7
8
1 Ceiling spray arm
2 Upper basket
3 Upper basket spray arm
4 Filters
5 Lower spray arm
6 Detergent dispenser
7 Rinse aid dispenser
8 Rating plate
9 Salt container
9
117986 48/0en
18-05-2007
9:24
Pagina 8
8 electrolux control panel
Control panel
1
On/Off button
2
Programme selection buttons
3
Indicator lights
117986 48/0en
18-05-2007
9:24
Pagina 9
control panel electrolux 9
Indicator lights
Wash
Illuminates when the washing and rinsing
phases are running.
Dry
Illuminates when the drying phase is running.
End of
programme
●
Light on when the appliance is in setting
mode, light off when a washing programme
is selected or in progress.
●
Illuminates when a washing programme has
ended.
●
It also has added functions of visual
signalling as:
- the setting of the water softener,
- activation/deactivation of the rinse aid
dispenser,
- intervention of an alarm due to the
malfunction of the machine.
Multi-tab
function
Indicates the activation/deactivation of the
Multi-tab function (see Multi-tab function).
Rinse aid
Illuminates when the rinse aid has run out.
Salt
Illuminates when the special salt has run out.
The salt and rinse aid indicator
lights are never illuminated while a
washing programme is running
even if filling with salt and/or rinse
aid is necessary.
117986 48/0en
18-05-2007
9:24
Pagina 10
10 electrolux control panel
Setting mode
●
●
Press On/Off button, ALL
programme button lights and end
of programme indicator light are
illuminated = appliance in setting
mode.
Press On/Off button, ONLY a
programme button light is
illuminated = last performed or
selected programme still set.
In this case, to return to setting
mode, the programme has to be
cancelled.
To cancel a set programme or a
programme in progress
Simultaneously press and hold the
two programme buttons positioned
over the letter C, until all the
programme button lights and end of
programme indicator light are
illuminated.
The programme has been cancelled
and the machine is now in setting
mode.
Always remember that when:
-
setting a washing programme,
-
setting the water softener,
-
activating/deactivating the rinse aid
dispenser,
the appliance MUST be in setting
mode.
117986 48/0en
18-05-2007
9:24
Pagina 11
first use electrolux 11
First use
Before using your dishwasher for the
first time:
● Ensure that the electrical and
water connections comply with the
installation instructions
● Remove all packaging from inside
the appliance
● Set the water softener
● Pour 1 litre of water inside the salt
container and then fill with
dishwasher salt
● Fill the rinse aid dispenser
If you want to use combi detergent
tablets such as: ‘3 in 1’, ‘4 in 1’, ‘5
in 1’ etc... set the Multi-tab function
(see Multi-tab function).
Set the water softener
The dishwasher is equipped with a
water softener designed to remove
minerals and salts from the water
supply, which would have a
detrimental or adverse effect on the
operation of the appliance.
The higher the content of these
minerals and salts, the harder your
water is.
Water hardness is measured in
equivalent scales, German degrees
(°dH), French degrees (°TH) and
mmol/l (millimol per litre - international
unit for the hardness of water).
The softener should be adjusted
according to the hardness of the
water in your area. Your local Water
Authority can advise you on the
hardness of the water in your area.
Number of
flashes of the
‘end of
programme’
indicator light
Use of
salt
°dH
°TH
mmol/l
Adjusting the
water
hardness
setting
51 - 70
91 - 125
9.0 - 12.5
level 10
10
yes
43 - 50
76 - 90
7.6 - 8.9
level 9
9
yes
37 - 42
65 - 75
6.5 - 7.5
level 8
8
yes
29 - 36
51 - 64
5.1 - 6.4
level 7
7
yes
23 - 28
40 - 50
4.0 - 5.0
level 6
6
yes
19 - 22
33 - 39
3.3 - 3.9
level 5
5
yes
15 - 18
26 - 32
2.6 - 3.2
level 4
4
yes
11 - 14
19 - 25
1.9 - 2.5
level 3
3
yes
4 - 10
7 - 18
0.7 - 1.8
level 2
2
yes
<4
<7
< 0.7
level 1
1
no *
Water hardness
* no salt is necessary
117986 48/0en
18-05-2007
9:24
Pagina 12
12 electrolux first use
The dishwasher is factory set at
level 5.
1. Press the On/Off button. The
dishwasher must be in setting
mode.
2. Press simultaneously and keep
pressed buttons 2 and 3, until the
lights of buttons 1, 2 and 3 start
flashing.
4. To change the level, press button
1. Each time the button is pressed
the level changes. (For the
selection of the new level see the
chart).
Examples:
if the current level is 5, by pressing
button 1 once, level 6 is selected.
if the current level is 10, by
pressing button 1 once, level 1 is
selected.
5. To memorise the operation, switch
off the dishwasher by pressing the
On/Off button.
3. Press button 1, the lights of
buttons 2 and 3 turn off while the
light of the button 1 goes on
flashing, at the same time the end
of programme indicator light
starts to flash.
The current level is indicated by
the number of flashes of the end
of programme indicator light.
Examples:
5 flashes, pause, 5 flashes, pause,
etc... = level 5
6 flashes, pause, 6 flashes, pause,
etc... = level 6
117986 48/0en
18-05-2007
9:24
Pagina 13
first use electrolux 13
Filling with dishwasher salt
Only use salt specifically designed for
use in dishwashers.
All other types of salt not specifically
designed for use in a dishwasher,
especially table salt, will damage the
water softener.
Only fill with salt just before starting
one of the complete washing
programmes.
This will prevent any grains of salt or
salty water, which may have been
spilt, remaining on the bottom of the
machine for any period of time, which
may cause corrosion.
To fill:
1. Open the door, remove the lower
basket and unscrew the cap of the
salt container by turning it
anticlockwise.
2. Pour 1 litre of water inside the
container (this is necessary only
before filling with salt for the
first time).
3. Pour in the salt until the container
is full.
4. Replace the cap making sure that
there is no trace of salt on the
screw thread or on the gasket.
5. Replace the cap tightly turning it
clockwise.
Do not worry if water overflows from
the unit when filling with salt, this is
quite normal.
The salt indicator light on the
control panel can remain
illuminated for 2-6 hours after the
salt has been replenished,
assuming the dishwasher remains
switched on. If you are using salts
that take longer to dissolve then
this can take longer. The function
of the machine is not affected.
117986 48/0en
18-05-2007
9:24
Pagina 14
14 electrolux first use
Filling with rinse aid
Rinse aid ensures thorough rinsing,
and spot and streak free drying.
Rinse aid is automatically added
during the last rinse.
According to the finish and drying
results obtained, adjust the dose of
rinse aid by means of the 6 position
selector (position 1 minimum dosage,
position 6 maximum dosage).
1. Open the container by pressing
the release button (A).
The dose is factory set in position 4.
2. Add the rinse aid in the container.
The maximum level for filling is
indicated by "max".
Increase the dose if there are drops of
water or lime spots on the dishes after
washing.
Reduce it if there are sticky whitish
streaks on the dishes or a bluish film
on glassware or knife blades.
3. Ensure that the lid is closed after
every refill.
The dispenser holds about 110 ml of
rinse aid, which is sufficient for
between 16 and 40 dishwashing
cycles, depending upon the dosage
setting.
Clean up any rinse aid spilt during
filling with an absorbent cloth to
avoid excess foaming during the
next wash.
Only use branded rinse aid for
dishwashers.
Never fill the rinse aid dispenser
with any other substances (e.g.
dishwasher cleaning agent, liquid
detergent). This would damage the
appliance.
117986 48/0en
18-05-2007
9:24
Pagina 15
daily use electrolux 15
Daily use
●
Check if it’s necessary to refill with
dishwasher salt or rinse aid
●
Load cutlery and dishes into the
dishwasher.
●
Fill with dishwasher detergent .
●
Select a wash programme suitable
for the cutlery and dishes.
●
Start the wash programme.
Loading cutlery and dishes
Sponges, household cloths and any
object that can absorb water may not
be washed in the dishwasher.
●
Before loading the dishes, you
should:
- Remove all left over food and
debris.
- Soften remnants of burnt food in
pans
●
When loading the dishes and
cutlery, please note:
- Dishes and cutlery must not
impede the rotation of the spray
arms .
- Load hollow items such as cups,
glasses, pans, etc. with the
opening downwards so that water
cannot collect in the container or
a deep base.
- Dishes and items of cutlery must
not lie inside one another, or
cover each other.
- To avoid damage to glasses, they
must not touch.
- Lay small objects in the cutlery
basket.
●
Plastic items and pans with non
stick coatings have a tendency to
retain water drops; these items will
not dry as well as porcelain and
steel items.
●
Light items (plastic bowls etc.)
must be loaded in the upper
basket and arranged so they do
not move.
117986 48/0en
18-05-2007
9:24
Pagina 16
16 electrolux daily use
For washing in the dishwasher the following cutlery and dishes
are not suitable:
- Cutlery with wooden, horn, china or mother-ofpearls handles.
- Plastic items that are not heat resistant.
- Older cutlery with glued parts that are not
temperature resistant.
- Bonded cutlery items or dishes.
- Pewter or copper items.
- Lead crystal glass.
- Steel items prone to rusting.
- Wooden platters.
- Items made from synthetics fibres.
are of limited suitability:
- Only wash stoneware in the dishwasher if it is
specially marked as being dishwasher-safe by the
manufacturer.
- Glazed patterns may fade if machine washed
frequently.
- Silver and aluminium parts have a tendency to
discolour during washing: Residues, e.g. egg
white, egg yolk and mustard often cause
discolouring and staining on silver. Therefore
always clean left-overs from silver immediately, if
it is not to be washed straight after use.
117986 48/0en
18-05-2007
9:24
Pagina 17
daily use electrolux 17
The lower basket
The lower basket is designed to take
saucepans, lids, plates, salad bowls,
cutlery etc.
A serving plate can be placed in front
of the cutlery basket.
The rear plate rack can be easily
folded down to allow you to load pots,
pans and bowls.
Folding down the right plate rack will
create another plate rack that allows
you to load deep plates and bowls.
1. Lift the two plate racks slightly at
the back and fold them inward
making them cross over one
another.
The left plate rack can be folded down
and the width can be adjusted.
●
To fold them down, lift the two
plate racks slightly at the back and
fold them onwards making them
cross over one another.
●
To set the width: pull the right-hand
plate rack upwards at the back
until it disengages, then pull it
towards the back out of the front
guide.
Insert the plate rack in the other
guide and press it down at the
back until it snaps in.
117986 48/0en
18-05-2007
9:24
Pagina 18
18 electrolux daily use
The cutlery basket
Long bladed knives stored in an
upright position are a potential
hazard.
Long and/or sharp items of cutlery
such as carving knives must be
positioned horizontally in the upper
basket.
Take care when loading or
unloading sharp items such as
knives.
To make loading of the cutlery basket
easier, lower the cutlery basket
handle (fig.2).
fig. 2
Forks and spoons should be placed in
the removable cutlery basket with the
handles facing downwards and the
knives with their handles facing
upwards (fig.1).
fig. 1
For best results we recommend you
to use the cutlery grids.
If the size and dimensions of the cutlery
do not allow the use of the grids, they
can be easily hidden (fig. 3).
fig. 3
If the handles protrude from the
bottom of the basket, obstructing the
lower spray arm, load the cutlery with
the handles facing upwards.
Mix spoons with other cutlery to
prevent them from sticking together.
117986 48/0en
18-05-2007
9:24
Pagina 19
daily use electrolux 19
The cutlery basket is in two parts
which can be separated to give
greater loading flexibility. To separate
the two parts, slide them horizontally
in opposite directions and pull them
apart (fig. 4).
fig. 4
To reassemble, reverse the
procedure.
117986 48/0en
18-05-2007
9:24
Pagina 20
20 electrolux daily use
The upper basket
The upper basket is designed for
saucers, salad bowls, cups, glasses,
pots and lids.
Glass holders
For glasses with long stems and tall
cylindrical glasses, fold up the glass
holder. (Top picture)
To unload or when not needed, fold
the glass holder back to the right.
(Middle picture).
Glasses can also be placed over the
bars pointing up. (Bottom picture).
Adjustable cup racks
● Arrange items on and underneath
the cup racks so that water can
reach all surfaces.
● The cup racks can be folded up
out of the way for tall crockery
items.
● The cup racks can also be fixed in
an intermediate position. Lay or
hang glasses with the stems in
the slots in the cup racks.
Before closing the door, ensure that
the spray arms can rotate freely.
117986 48/0en
18-05-2007
9:24
Pagina 21
daily use electrolux 21
Adjusting the height of the upper basket
If washing very large plates you can load them in the lower basket after moving
the upper basket to the higher position.
The adjustment of the height of the
upper basket is possible also when
the basket has been loaded.
Moving the upper basket to the
higher / lower position:
1. Pull out the basket completely.
2. Raise the upper basket as far as it
will go and then lower it vertically.
The upper basket will latch into the
lower or higher position.
After loading your machine always
close the door, as an open door can
be a hazard.
117986 48/0en
18-05-2007
9:24
Pagina 22
22 electrolux daily use
Maximum plate sizes with upper
basket in higher position.
18
32
25
Arrangement of large plates in the
lower basket
Maximum plate sizes with upper
basket in lower position.
20
30
25
117986 48/0en
18-05-2007
9:24
Pagina 23
daily use electrolux 23
Use of detergent
20 = approximately 20 g of
detergent
30 = approximately 30 g of
detergent
Only use detergents specifically
designed for use in dishwashers.
Please observe the manufacturer’s
dosing and storage recommendations
as stated on the detergent packaging.
3. All programmes with prewash
need an additional detergent dose
(5/10 g) that must be placed in the
prewash detergent chamber (2).
This detergent will take effect
during the prewash phase.
When using detergent tablets;
place the tablet in compartment (1)
Using no more than the correct
amount of detergent contributes to
reducing pollution.
Fill with detergent
1. Open the lid.
4. Close the lid and press until it
locks in place.
2. Fill the detergent dispenser (1)
with detergent. The marking
indicates the dosing levels:
1
2
Detergent tablets
Detergent tablets from different
manufactures dissolve at different
rates. For this reason, some detergent
tablets do not attain their full cleaning
power during short washing
programmes. Therefore, please use
long washing programmes when
using detergent tablets, to ensure the
complete removal of detergent
residuals.
117986 48/0en
18-05-2007
9:24
Pagina 24
24 electrolux daily use
Multi-tab function
This appliance is equipped with the
Multi-tab function, that allows the use
of combi detergent tablets.
These products are detergents with a
combined cleaning, rinsing and salt
functions. They can also contain other
different agents depending on which
kind of tablets you choose (‘3 in 1’, ‘4
in 1’, ‘5 in 1’ etc...)
Check whether these detergents are
suitable for your water hardness. See
the manufacturers instructions.
Once this function is selected it will
remain active also for the following
washing programmes.
With the selection of this function the
inflow of rinse aid and salt from each
respective supply container is
automatically deactivated and also the
indicator lights for salt and rinse aid
are deactivated.
Select the Multi-tab function before
the start of a washing programme.
With the use of the Multi-tab function,
the cycle durations may change.
Once the programme is running, the
Multi-tab function can NO longer be
changed. If you want to exclude the
Multi-tab function you have to cancel
the programme setting and then
deactivate the Multi-tab function.
In this case you have to set a
washing programme again.
Activation/deactivation of the Multitab function
Simultaneously press and hold the
two buttons positioned over the Multitab symbol, until the Multi-tab
indicator light illuminates. This means
that the function is active.
To deactivate the function press the
same buttons again until the Multi-tab
indicator light turns off.
If the drying results are not
satisfactory we suggest that you:
1. Fill up the rinse aid dispenser with
rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to
position 2.
●
The activation/deactivation of the
rinse aid dispenser can only be
possible with the Multi-tab function
active.
117986 48/0en
18-05-2007
9:24
Pagina 25
daily use electrolux 25
Activation/deactivation of the rinse
aid dispenser
1. Press the On/Off button. The
dishwasher must be in setting
mode.
2. Simultaneously press and hold
buttons 2 and 3, until the lights of
buttons 1, 2, and 3 start flashing.
If you decide to turn back to the
use of standard detergent system
we advise that you:
1. Deactivate the Multi-tab function.
2. Fill up the salt container and the
rinse aid dispenser again.
3. Adjust the water hardness setting
to the highest setting and perform
1 normal washing programme
without loading any dishes.
4. Adjust the water hardness setting
according to the hardness of the
water in your area.
3. Press button 2, the indicator lights
of buttons 1 and 3 turn off while
the indicator light of button 2 goes
on flashing.
4. To activate the rinse aid dispenser,
press button 2 again, the end of
programme indicator light
illuminates, indicating that the rinse
aid dispenser has been activated.
5. To memorise the operation, switch
off the dishwasher by pressing the
On/Off button.
6. To deactivate the rinse aid
dispenser again, follow the above
instructions until the end of
programme indicator light turns
off.
5. Adjust the rinse aid dosage.
117986 48/0en
18-05-2007
9:24
Pagina 26
26 electrolux daily use
Select and start a washing
programme
Select the washing programme
with the door slightly opened. The
start of the programme will occur
only after the closure of the door.
Until then it is possible to modify
the settings.
1. Check that the baskets have been
loaded correctly and that the spray
arms are free to rotate
2. Check that the water tap is opened
3. Press the On/Off button. The
dishwasher must be in setting
mode.
4. Press the button corresponding to
the required programme (see
‘Washing programmes’ chart).
The phase indicator lights foreseen
for that programme start flashing.
5. Close the dishwasher door, the
programme starts automatically.
Once the programme has started
the phase indicator lights will turn
off except for the phase under
way.
Interrupt or cancel a washing
programme in progress ONLY if it’s
absolutely necessary.
Attention! Hot steam may escape
when the door is opened. Open the
door carefully.
Interrupt a washing programme in
progress:
● Open the dishwasher door; the
programme will stop. Close the
door; the programme will start from
the point at which it was
interrupted.
●
Press the On/Off button (all
indicator lights will turn off); the
programme will stop. Press the
On/Off button again; the
programme will start from the point
at which it was interrupted.
Cancel a washing programme in
progress
● Simultaneously press and hold the
two programme buttons positioned
over the letter C, until all the
programme button lights and end
of programme indicator light are
illuminated.
The washing programme has been
cancelled.
●
If a new washing programme is to
be selected, check that there is
detergent in the detergent
dispenser.
117986 48/0en
18-05-2007
9:24
Pagina 27
daily use electrolux 27
End of the washing programme
● The dishwasher will automatically
stop.
●
The end of programme indicator
light is illuminated.
●
The indicator light of the
programme just ended will remain
illuminated.
1. Switch off the dishwasher by
pressing the On/Off button.
2. Open the dishwasher door and
leave it ajar; wait a few minutes
before removing the dishes; in this
way they will be cooler and the
drying will be improved.
Unloading the dishwasher
● Hot dishes are sensitive to knocks.
The dishes should therefore be
allowed to cool down before
removing from the appliance.
● Empty the lower basket first and
then the upper one; this will avoid
water dripping from the upper
basket onto the dishes in the lower
one.
● Water may appear on the sides
and the door of the dishwasher as
the stainless steel will eventually
become cooler than the dishes.
When the washing programme has
finished, it is recommended that
the dishwasher is unplugged and
the water tap turned off.
117986 48/0en
18-05-2007
9:24
Pagina 28
28 electrolux washing programmes
Washing programmes
Programme
Degree of soil
Type of load
Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
Normal soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 55°C
1 intermediate rinse
Final rinse
Drying
Normal soil
Crockery and
cutlery
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
Normal or
light soil
Crockery and
cutlery
Main wash up to 60°C
Final rinse
Normal soil
Delicate
crockery and
glassware
Main wash up to 45°C
1 intermediate rinse
Final rinse
Drying
Intensive
Normal
Eco (1)
Quick (2)
Glass
Prewash
Any.
Partial load (to be completed
later in the day).
Washing programmes information
(1) Test programme for test institutes.
(2) Ideal for washing a partially loaded
dishwasher. This is the perfect
daily programme, made to meet
the needs of a family of 4
persons who only wish to load
breakfast and dinner crockery and
cutlery.
Programme description
1 cold rinse (to avoid food
scraps from sticking together).
This programme does not
require the use of detergent.
117986 48/0en
18-05-2007
9:24
Pagina 29
care and cleaning electrolux 29
Care and cleaning
Cleaning the filters
The filters must be checked and
cleaned from time to time. Dirty filters
will degrade the washing result.
NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and will result in
damage to the appliance.
Fine filter
The fine filter (2) must be cleaned
from time to time.
1. Open the door and remove the
lower basket.
2. Take hold of the fine filter by the
handle and remove by turning it to
the right.
3. Clean the fine filter thoroughly with
a brush under running water.
Before cleaning the filters ensure
that the machine is switched off.
1
2
Coarse filter
The coarse filter (1) must be checked
after every washing programme.
1. Open the door, remove the lower
basket.
2. Remove the coarse filter and if
necessary clean it thoroughly
under running water.
3. Replace the coarse filter.
4. Put the fine filter back in the base
of the washing compartment and
ensure that it fits perfectly by
turning to the left until you feel it
click into place (arrow).
117986 48/0en
18-05-2007
9:24
Pagina 30
30 electrolux care and cleaning
Cleaning the spray arms
Regularly check the nozzles in the 3
spray arms for blockages. If
necessary clean the nozzles with a
piece of fine wire or a fine needle and
a strong water jet.
Upper basket spray arm
1. Remove the upper basket spray
arm by turning it laterally.
Do not damage the nozzle openings.
2. Clean spray arm nozzles.
3. To replace the spray arm, press
upwards until you feel it snap into
place.
Ceiling spray arm
1. Undo the fixing screw (A) by
turning it anti-clockwise.
2. Pull the spray arm off the shaft.
A
3. Clean the spray arm and the fixing
screw.
4. Fasten the spray arm with the
fixing screw (A) by turning it
clockwise.
Lower spray arm
1. Undo the fixing screw (B) by
turning it anti-clockwise.
2. Pull the spray arm off the shaft.
B
3. Clean the spray arm and the fixing
screw.
4. Fasten the spray arm with the
fixing screw (B) by turning it
clockwise.
117986 48/0en
18-05-2007
9:24
Pagina 31
care and cleaning electrolux 31
External cleaning
Clean the external surfaces of the
machine and control panel with a
damp soft cloth. If necessary use only
neutral detergents. Never use
abrasive products, scouring pads or
solvent (acetone, trichloroethylene
etc....).
●
Polished chromium steel
surfaces
Remove light dirt with a clean,
damp, soft cloth. Microfibre cloths
are particularly good.
When cleaning ensure that you do not
go against the direction of the
stainless steel finish (the fine
horizontal lines).
No circular movements!
●
Aluminium look surfaces
Remove light dirt with a clean,
damp, soft cloth. Microfibre cloths
are particularly good.
●
Agents that scratch or scour are
not suitable.
●
If required, use a commercially
available cleaner for chrome
surfaces. Follow the
manufacturer’s instructions when
using these products.
Internal cleaning
Ensure that the seals around the
door, the detergent and rinse aid
dispensers are cleaned regularly with
a damp cloth.
We recommend every 3 months to
run the wash programme for heavy
soiled dishes using detergent but
without dishes.
Prolonged periods of nonoperation
If you are not using the machine for
any prolonged period of time you are
advised to:
1. Unplug the appliance and then
turn off the water.
2. Leave the door ajar to prevent the
formation of any unpleasant
smells.
3. Leave the inside of the machine
clean.
Frost precautions
Avoid placing the machine in a
location where the temperature is
below 0°C. If this is unavoidable,
empty the machine, close the
appliance door, disconnect the water
inlet pipe and empty it.
Moving the machine
If you have to move the machine
(moving house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and
discharge hoses.
4. Pull the machine out together with
the hoses.
Avoid over tilting the machine during
transportation.
117986 48/0en
18-05-2007
9:24
Pagina 32
32 electrolux something not working
Something not working
The dishwasher will not start or stops during operation.
Certain problems are due to the lack of simple maintenance or oversights,
which can be solved with the help of the indications described in the chart,
without calling out an engineer.
Switch off the appliance and carry out the following suggested corrective
actions.
Fault code and malfunction
●
continuous flashing of the light of the
running programme
●
1 flash of the ‘end of programme’
indicator light
The dishwasher does not fill with water
Possible cause and solution
●
The water tap is blocked or furred with
limescale.
Clean the water tap.
●
The water tap is turned off.
Turn the water tap on.
●
The filter (where present) in the threaded
hose fitting at the water inlet valve is
blocked.
Clean the filter in the threaded hose.
●
The water inlet hose has not been
correctly laid or it is bent or squashed.
Check the water drain hose connection.
●
continuous flashing of the light of the
running programme
●
The sink spigot is blocked.
Clean out the sink spigot.
●
2 flashes of the ‘end of programme’
indicator light
●
The water drain hose has not been
correctly laid or it is bent or squashed.
Check the water drain hose connection.
●
Close the water tap and contact your
local Service Force Centre.
The dishwasher will not drain
●
continuous flashing of the light of the
running programme
●
3 flashes of the ‘end of programme’
indicator light
Anti-flood device is activated
117986 48/0en
18-05-2007
9:24
Pagina 33
something not working electrolux 33
Malfunction
The programme does not start
Once these checks have been carried
out, switch on the appliance.
The programme will continue from the
point at which it was interrupted.
If the malfunction or fault code
reappears contact the Service Force
Centre.
For other fault codes not described in
the above chart, please contact your
Service Force Centre.
Contact your local Service Force
Centre, quoting the model (Mod.),
product number (PNC) and serial
number (S.N.).
This information can be found on the
rating plate located on the side of the
dishwasher door.
So that you always have these
numbers at hand, we recommend you
to make a note of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . .
PNC :. . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . .
Possible cause and solution
●
The dishwasher’s door has not been
properly closed.
Close the door.
●
The main plug is not plugged in.
Insert the main plug.
●
The fuse has blown out in the household
fuse box.
Replace the fuse.
117986 48/0en
18-05-2007
9:24
Pagina 34
34 electrolux something not working
The wash results are not satisfactory
The dishes are not
clean
The dishes are wet and
dull
There are streaks, milky
spots or a bluish
coating on glasses and
dishes
Water drops have dries
onto glasses and dishes
●
The wrong washing programme has been selected.
●
The dishes are arranged in such a way as to stop water
reaching all parts of the surface. The baskets must not
be overloaded.
●
The spray arms do not rotate freely due to incorrect
arrangement of the load.
●
The filters in the base of the washing compartment are
dirty or incorrectly positioned.
●
Too little or no detergent has been used.
●
Where there are limescales deposits on the dishes; the
salt container is empty or the incorrect level of the water
softener has been set.
●
The drain hose connection is not correct.
●
The salt container cap is not properly closed.
●
Rinse aid was not used.
●
The rinse aid dispenser is empty.
●
Decrease rinse aid dosing.
●
Increase rinse aid dosing.
●
The detergent may be the cause. Contact the detergent
manufacturer’s consumer care line.
If after all these checks, the problem
persists, contact your local Service
Force Centre.
117986 48/0en
18-05-2007
9:24
Pagina 35
technical data electrolux 35
Technical data
Dimensions
Width
54.6 cm
Height
75.9 cm
Depth
56.3 cm
Electrical connection
Voltage - Overall power Fuse
Information on the electrical connection is given
on the rating plate on the inner edge of the
dishwasher’s door
Water supply pressure
Minimum
0.5 bar (0.05 MPa)
Maximum
8 bar (0.8 MPa)
Capacity
Max. weight
Subject to change without notice
11 place settings
55,5 kg
117986 48/0en
18-05-2007
9:24
Pagina 36
36 electrolux technical data
Consumption values
Programme
Programme
duration
(in minutes)
Energy
consumption
(in kWh)
Water
consumption
(in litres)
Intensive
105 - 115
1.8 - 2.0
22 - 24
Normal
100 - 110
1.3 - 1.5
15 - 17
175
1.0
14
Quick
30
0.9
8
Glass
65 - 75
0.8 - 0.9
13 - 14
7
0.1
4
Eco
(Test programme
for test institutes)
Prewash
The consumption values are intended
as a guide and depends on the
pressure and the temperature of the
water and also by the variations of the
power supply and the amount of
dishes.
117986 48/0en
18-05-2007
9:24
Pagina 37
hints for test institutes electrolux 37
Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance
fully loaded and using the test
programme (see "Consumption
values").
Test in accordance with EN 50242
must be carried out when the salt
container and rinse aid dispenser
have been filled with salt and rinse aid
respectively and using the test
programme (see "Consumption
values").
Full load: 11 standard place settings
3
3
Amount of detergent required:
27,5 (Type B)
Rinse aid setting:
position 6 (Type III)
3
6
3
1
8
1
3
3
1
1
3
1
1
3
1
3
1
3
1
1
3
1
1
1
5
5
5
5
5
5
5
5
5
5
5
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
4
5
7
7
1
2
3
6
7
8
Arrangement cutlery basket
117986 48/0en
18-05-2007
9:24
Pagina 38
38 electrolux hints for test institutes
Arrangement upper basket
(upper basket in lowered position)
Arrangement lower basket
117986 48/0en
18-05-2007
9:24
Pagina 39
installation electrolux 39
Installation
Any electrical and/or plumbing
work required to install this
appliance should be carried out by
a qualified electrician and/or
plumber or competent person.
Remove all packaging before
positioning the machine.
If possible, position the machine next
to a water tap and a drain.
This dishwasher is designed to be
fitted under a kitchen counter or
worksurface.
No further openings for the venting of
the dishwasher are required, but only
to let the water fill and drain hose and
power supply cable pass through.
During all operations that involve
accessibility to internal components
the dishwasher has to be unplugged.
When inserting the machine, ensure
that the water inlet hose, the drain
hose and the supply cable are not
kinked or squashed.
Fixing to the adjacent units
The dishwasher must be secured
against tilting.
Therefore make sure that the counter
it is fixed under, is suitably secured to
a fixed structure (adjacent kitchen
units cabinets, wall).
Water supply connections
This dishwasher may be fed with
either hot (max. 60°) or cold water.
Nevertheless we advise you a cold
water supply.
A hot water supply is not always
efficient with very soiled crockery as it
shortens the washing programmes a
lot.
For making the connection itself, the
coupling nut fitted to the machine’s
supply hose is designed to screw onto
a 3/4" gas thread spout or to a
purpose made quick-coupling tap
such as the Press-block.
The water pressure must be within
the limits given in the "Technical
data". Your local Water Authority will
advise you on the average mains
pressure in your area.
The water inlet hose must not be
kinked, crushed, or entangled when it
is being connected.
The dishwasher features fill and drain
hoses which can be turned either to
the left or the right to suit the
installation by means of the locknut.
The locknut must be correctly fitted
to avoid water leaks.
(Attention! NOT all models of
dishwashers have fill and drain hoses
provided with locknut. In this case,
this kind of facility is not possible).
If the machine is connected to new
pipes or pipes which have not been
used for a long time, you should run
the water for a few minutes before
connecting the inlet hose.
DO NOT use connection hoses
which have previously been used
for an old appliance.
Installation of an IRG filter is
recommended on the construction
side.
117986 48/0en
18-05-2007
9:24
Pagina 40
40 electrolux installation
●
Place the water inlet hose in such
a way that it is never higher than
the bottom edge of the safety
valve.
K E
A
C
70
C
G 546
100
N 550
180
550
B
20
B
Warning!
Dangerous voltage
A = drain outlet
G = size of the appliance
K = cold water supply
N = size of the recess
W = hot water supply
E = socket
50
600
W
400
A water inlet hose with safety valve
must only be replaced by the
Service Force Centre.
D
max. 700
●
If water inlet hose or the safety
valve is damaged, remove the
mains plug immediately.
D
G 759
●
The electrical cable for the safety
valve is in the double-walled water
inlet hose. Do not immerse the
water inlet hose or the safety valve
in water.
N 762+3
●
105
Please take care when installing the
water inlet hose:
G 570
After connecting the double-walled
water inlet hose, the safety valve is
next to the tap. Therefore the water
inlet hose is only under pressure
while the water is running. If the water
inlet hose starts to leak during this
operation, the safety valve cuts off the
running water.
Water outlet hose connection
The drain hose can face either to the
right or left of the dishwasher
Ensure the hose is not bent or
squashed as this could prevent or
slow down the discharge of water.
The sink plug must not be in place
when the machine is draining as this
could cause the water to syphon back
into the machine.
The waste connection must be at a
maximum height of 70 cm from the
ground.
N 600
Water inlet hose with safety valve
117986 48/0en
18-05-2007
9:24
Pagina 41
installation electrolux 41
When connecting the drain hose to an
under sink trap spigot, the entire
plastic membrane (A) must be
removed. Failure to remove all the
membrane will result in food particles
building up over time eventually
blocking the dishwasher drain hose
spigot
Our appliances are supplied with a
security device to protect against the
return of dirty water back into the
machine.
If the spigot of your sink has a "no
return valve" incorporated this can
prevent the correct draining of your
dishwasher. We therefore advise you
to remove it.
Electrical connection
Safety standards require the
appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated
voltage and type of supply on the
rating plate match that of the
supply where the appliance is to be
installed. The fuse rating is also to
be found on the rating plate.
Always plug the mains plug into a
correctly installed shockproof
socket.
Multi-way plugs, connectors and
extension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic
wiring system socket replaced. In
case that the electrical cable has to
be replaced, contact your local
Service Force centre.
The plug must be accessible after
the appliance has been installed.
Never unplug the appliance by
pulling on the cable. Always pull
the plug.
The manufacturer accepts no
liability for failure to observe the
above safety precautions.
117986 48/0en
18-05-2007
9:24
Pagina 42
42 electrolux installation
1. Stand the appliance in front of the
kitchen unit. Place cable and
hoses into the neighbouring unit.
Other fixing possibilities:
on the plinth
2. Push the appliance in, pull the
cable and hoses through and
ensure that they are not kinked or
squashed.
50
105
3. Line up the appliance and fix it on
both sides in the upper area of the
tub casing.
Additional bracket on the top available as special accessory
(contact your local Service Force
Centre)
117986 48/0en
18-05-2007
9:24
Pagina 43
environment concerns electrolux 43
Environment concerns
Packaging material
The packaging materials are
environmentally friendly and can be
recycled. The plastic components are
identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste
disposal facilities.
When a unit is no longer being used:
- Pull the plug out of the socket.
- Cut off the cable and plug and
dispose of them.
- Dispose of the door catch. This
prevents children from trapping
themselves inside and
endangering their lives.
Old appliance
The symbol
on the product or on
its packaging indicates that this
product may not be treated as
household waste. Instead it shall be
handed over to the applicable
collection point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed
of correctly, you will help prevent
potential negative consequences for
the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product.
For more detailed information about
recycling of this product, please
contact your local city office, your
household waste disposal service or
the shop where you purchased the
product.
117986 48/0en
18-05-2007
9:24
Pagina 44
44 electrolux warranty/point of service
Warranty/Point of service
Servicestellen
Points de service
Servizio dopo vendita
Point of service
5506 Mägenwil/Zürich
Industriestr. 10
9000 St. Gallen
Zürcherstrasse 204 e
4127 Birsfelden
Hauptstrasse 52
6020 Emmenbrücke
Seetalstrasse 11
7000 Chur
Comercialstrasse 19
Service-Helpline
0848 848 111
[email protected]
3018 Bern
Morgenstrasse 131
1028 Préverenges Le
Trési 6
6916 Grancia
Zona Industriale E
Ersatzteilverkauf / Point de vente de rechange / Vendita pezzi di ricambio /
spare parts service
55 Mägenwil, Industriestrasse 10, Tel. 0848 848 023
Fachberatung, Verkauf/Demonstration, Vente/Consulente (cucina),
Vendita/consulting, sales
8048 Zürich, Badenerstrasse 587, Tel. 044 405 81 11
117986 48/0en
18-05-2007
9:24
Pagina 45
warranty/point of service electrolux 45
Garantie
Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum
an den Endverbraucher eine Garantie von 2 Jahren.
(Ausweis durch Garantieschein, Faktura oder Verkaufsbeleg).
Die Garantieleistung umfasst die Kosten für Material, Arbeitsund Reisezeit.
Die Garantieleistung entfällt bei Nichtbeachtung der
Gebrauchsanweisung und Betriebsvorschriften,
unsachgerechter Installation, sowie bei Beschädigung durch
äussere Einflüsse, höhere Gewalt, Eingriffe Dritter und
Verwendung von Nicht-Original Teilen.
Garantie
Nous octroyons sur chaque produit 2 ans de garantie à partir
de la date de livraison ou de la mise en service au
consommateur (documenté au moyen d’une facture, d’un bon
de garantie ou d’un justificatif d’achat). Notre garantie couvre
les frais de mains d’oeuvres et de déplacement, ainsi que les
pièces de rechange.
Les conditions de garantie ne sont pas valables en cas
d’intervention d’un tiers non autorisé, de l’emploi de pièces
de rechange non originales, d’erreurs de maniement ou
d’installation dues à l’inobservation du mode d’emploi, et
pour des dommages causés par des influences extérieures
ou de force majeure.
Garanzia
Per ogni prodotto concediamo una garanzia di 2 anni a
partire dalla data di consegna o dalla sua messa in funzione.
(Fa stato la data della fattura, del certificato di garanzia o
dello scontrino d’acquisto) Nella garanzia sono comprese le
spese di manodopera, di viaggio e del materiale.
Dalla copertura sono esclusi il logoramento ed i danni causati
da agenti esterni, intervento di terzi, utilizzo di ricambi non
originali o dalla inosservanza delle prescrizioni d’istallazione
ed istruzioni per l’uso.
Warranty
For each product we provide a two-year guarantee from the
date of purchase or delivery to the consumer (with a
guarantee certificate, invoice or sales receipt serving as
proof).
The guarantee covers the costs of materials, labour and
travel.
The guarantee will lapse if the operating instructions and
conditions of use are not adhered to, if the product is
incorrectly installed, or in the event of damage caused by
external influences, force majeure, intervention by third
parties or the use of non-genuine components.
117986 48/0en
18-05-2007
9:24
Pagina 46
46 electrolux
Notes
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
...........................................................
117986 48/0en
18-05-2007
9:24
Pagina 47
117986 48/0en
18-05-2007
9:24
www.electrolux.com
www.electrolux.ch
117986 48/0-00-21032007
Pagina 48

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement