ZANUSSI ZWT71201WA User Manual

Add to My manuals
32 Pages

advertisement

ZANUSSI ZWT71201WA User Manual | Manualzz
User Manual
GETTING
STARTED?
EASY.
ZWT 71201 WA
EN User Manual
Washer Dryer
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away unless
continuously supervised.
Children of less than 3 years of age should be kept away
unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
2
Do not change the specification of this appliance.
The appliance shall be installed as a freestanding product or
below the kitchen worktop if space margins permit.
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not install the appliance behind a lockable door, a sliding
door or a door with a hinge on the opposite side, that would
prevent the appliance door from being fully open.
Connect the mains plug to the mains socket only at the end of
the installation process. Make sure that the mains plug is
accessible after installation.
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
WARNING: The appliance must not be supplied through an
external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by a utility.
Ensure good air ventilation in the room where the appliance is
installed to avoid the backflow of unwanted gases into the room
from appliances burning gas or other fuels, including open fires.
Exhaust air must not be discharged into a flue which is used for
exhausting fumes from any appliances burning gas or other
fuels.
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Wipe away lint or packaging debris that has accumulated
around the appliance.
Items that have been soiled with substances such as vegetable
or mineral oil, acetone, alcohol, petrol, kerosene, spot removers,
turpentine, waxes and wax removers should be washed
separately with an extra amount of detergent before being dried
in the washer dryer.
3
•
•
•
•
•
•
•
•
•
•
Do not use the appliance if items have been soiled with
industrial chemicals.
Do not dry unwashed items in the wash dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, and rubber backed articles and clothes, or
pillows fitted with foam rubber pads should not be dried in the
washer dryer.
Fabric softeners, or similar products, should only be used as
specified by the product manufacturer’s instructions.
Remove all objects from items that could be a source of fire
ignition such as lighters or matches.
Never stop the washer dryer before the end of the drying cycle
unless all items are quickly removed and separated so that
residual heat can dissipate.
The final part of the washer dryer cycle takes place without heat
(cool down cycle) to ensure that items reach a temperature that
will not cause damage to them.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
•
•
•
•
4
Follow the installation instructions supplied with
the appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
Always keep the appliance vertical when it is
being moved.
Make sure that there is air circulation between
the appliance and the floor.
Remove all the packaging and the transit bolts.
•
•
•
•
•
•
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not install or use a damaged appliance.
Do not install the appliance where the appliance
door cannot be fully opened.
Adjust the feet to have the necessary space
between the appliance and the flooring.
•
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Do not touch the mains cable or the mains plug
with wet hands.
UK and Ireland only. This appliance is fitted with
a 13 A mains plug. If it is necessary to change
the mains plug fuse, use only a 13 A ASTA (BS
1362) fuse.
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
•
•
•
This appliance is for household use only.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not touch the glass door while a programme
is in operation. The glass can get hot.
Do not dry damaged (torn, frayed) items that
contain padding or fillings.
If laundry has been washed with a stain
remover, carry out an additional rinse cycle
before starting a drying cycle.
Make sure that all metal objects are removed
from the laundry.
Only dry fabrics that are suitable to dry in the
washer dryer. Follow the cleaning instruction on
the item label.
Plastic items are not heat resistant.
– If a detergent ball is used, remove it before
starting a drying programme.
– Do not use a detergent ball if setting a nonstop programme.
WARNING! Risk of injury or damage
to the appliance.
•
•
Do not sit or stand on the open door.
Do not dry dripping wet clothes in the
appliance.
DISPOSAL
• Disconnect the appliance from the mains
electrical and water supplies.
• Cut off the mains electrical cable close to the
appliance and dispose of it.
• Remove the door catch to prevent children or
pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
5
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
3
4
5
6
1 Detergent dispenser
2 Control panel
3 Door handle
4 Rating plate
5 Drain pump filter
6 Feet for levelling the appliance
CHILD SAFETY
This device prevents children or pets to be closed
in the drum.
• Turn the device clockwise, until the groove
is horizontal.
You cannot close the
door.
• To close the door,
turn the device anticlockwise until the
groove is vertical.
6
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1
24
1
23
2
3
22
4
21
5
20
6
19
18
7
8
17
9
16
15
10
14 13 12 11
2
3
4
Delay
Start
1200
900
700
Eco
400
Rinse
Hold
Door
Quick
Wash
Spin
Option
Extra
Rinse
10
9
8
Drying
Time
Easy
Iron
Start/Pause
7
6
5
1 Programme knob and On/Off position
2 Display
7 Drying Time button (Drying Time)
3 Delay Start button (Delay Start)
9 Options button (Option)
4 Door Locked indicator (Door)
10 Spin Reduction button (Spin)
8 Extra Rinse button (Extra Rinse)
5 Start/Pause button (Start/Pause)
6 Easy Iron button (Easy Iron )
DISPLAY
A
B
•
The display shows:
A. Child lock indicator
This device permits you to leave the appliance
unattended during it's functioning (see «Child
Lock» paragraph).
The indicator comes when the related option is
set.
B. This area shows:
• Programme time
•
•
After the programme selection, the duration
is displayed in hours and minutes (for
example 2.10).
The duration is calculated automatically on
the basis of the maximum recommended
load for each type of fabric.
After the programme start, the time
remaining is updated every minute
Selected drying time
After selecting a drying programme, the
drying time is displayed in minutes or in
hours and minutes (e.g. 130 mins = 2.10).
After the programme start, the time
remaining is updated every minute.
End of programme
When the programme has finished three
flashing zeros are displayed.
Delay start
When you press the delay start button, the
display shows the delay start time.
7
•
•
After the programme start, the set delay
appears for few seconds, then the duration
of the set programme is displayed again.
Alarm codes
If the appliance has a malfunction, the
display shows the alarm codes. Refer to the
chapter 'Troubleshooting' .
Incorrect option selection
The display shows the message
some seconds and the Start/Pause
indicator button flashes if :
– You set a option that is not suitable for
the programme.
– You change the programme while it
operates.
for
PROGRAMMES
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
Washing programmes
1-5
Cottons1)
7 kg
1200 rpm
White cotton and coloured cotton.
Normal, heavy and light soil.
7 kg
1200 rpm
White cotton and coloured cotton.
Heavy soil and normal soil.
3 kg
900 rpm
Synthetic items or mixed fabric
items. Normal soil.
3 kg
700 rpm
Delicate fabrics such as acrylics,
viscose and mixed fabrics requiring gentler washing. Normal soil.
3 kg
1200 rpm
Items in denim and jersey. Also for
dark coloured items.
2 kg
900 rpm
Machine washable wool, hand
washable wool and other fabrics
with «hand washing» care symbol2).
90°C - 60°C - 40°C 30°C - Cold
6-8
Cottons + Prewash
90°C- 60°C - 40°C
9 - 12
Synthetics
60°C - 40°C - 30°C Cold
13 15
Delicates
40°C - 30°C - Cold
16
Jeans
40°C
17 19
Handwash
40°C - 30°C - Cold
Drying
8
Maximum load
Maximum spin
speed
Programme
Temperature range
20
Programme description
(Type of load and soil level)
4 kg
Drying programme for cotton items.
2 kg
Drying programme for synthetic
items.
7 kg
1200 rpm
To rinse and spin the laundry. All fabrics, except woollens and very delicate
fabrics. Reduce the spin speed accordingly to the type of laundry.
7 kg
To drain the water after programme
with the optionRinse Hold set.
7 kg
1200 rpm
To spin and drain the water after programme with the option Rinse Hold set.
Set the spin speed according to the
fabric to be spun.
Dry - Cottons
21
Dry - Synthetics
Extra
22
Rinses
23
Drain
24
Spin
1) «The programme Cottons at 60°C with a load of 7 kg, with the option Eco set , is the '«Cottons Energy
Saving Programme», reference programme for the data entered in the energy label in compliance with EEC
92/75 standards.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
Programme options compatibility
Programme
Spin
Rinse Hold
Eco
Quick
Wash
Extra
Rinse
Easy Iron
Cottons
■
■
■
■
■
■
Cottons + Prewash
■
■
■
■
■
■
Synthetics
■
■
■
■
■
■
■
■
Delicates
Jeans
■
■
Handwash
■
■
Rinses
■
■
Drain
■
■
■
■
■
Spin
9
PROGRAMMES FOR TIMED DRYING
Dryness Level
Type of fabric
Extra Dry
For towelling materials
Cottons and Linen
(bathrobes, bath towels, etc)
Cupboard
For items to be stored
Cottons and Linen
(bathrobes, bath towels, etc)
Cupboard Dry
For items to be stored
Synthetics and mixed fabrics
(jumpers, blouses, underwear,
household linen)
Iron Dry
Suitable for ironing
Cottons and Linen
(sheets, tablecloths, shirts, etc)
Dry1)
Load (kg)
Spin
speed
(rpm)
Suggested
duration
(mins)
4
1200
215 - 220
3
1200
160 - 180
1.5
1200
95 - 105
4
1200
205 - 210
3
1200
150 - 170
1.5
1200
85 - 95
2
900
90 - 100
1
900
55 - 65
4
1200
140 - 150
3
1200
90 - 100
1.5
1200
60 - 70
1) Hints for test institute. The test performance, in accordance with EN 50229:2015, must be carried
out with a FIRST drying load of the maximum declared drying capacity by setting 210 minutes by means of
the Drying Time button for the Dry - Cottons programme. The SECOND drying load with the residual load
must be tested by setting 130 minutes by means of the Drying Time button for the Dry - Cottons programme.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
Programmes
Cottons 60°C
10
Load (kg)
7
Energy conApproximate proWater consumption
gramme duration (misumption (litre)
(kWh)
nutes)
1.35
67
150
Programmes
Load (kg)
Energy conApproximate proWater consumption
gramme duration (misumption (litre)
(kWh)
nutes)
Cottons Eco
Cotton Energy Saving Programme 60°C1)
7
1.05
55
185
Cottons 40°C
7
0.85
67
140
Synthetics 40°C
3
0.55
42
90
Delicates 40°C
3
0.55
63
65
Wool/Handwash 30°C
2
0.25
55
60
1) «Cotton Energy Saving programme » at 60°C with a load of 7kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
OPTIONS
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
RINSE HOLD
• Set this option to prevent the laundry creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the laundry
creases.
• The door stays locked. You must drain the water
to unlock the door.
To drain the water refer to ‘At the end
of the programme’.
OPTION
Press this button to set one of the following
options:
The related indicator comes on.
•
•
Eco
Use this option if you want to wash laundry
saving energy.
The time is prolonged while the temperature is
reduced.
Only for cottons and synthetic items with normal
or light soil at a temperature of 40°C or higher.
Quick Wash
Press this button to decrease the programme
duration.
Set this option for items with light soil or items
to refresh.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related phase indicator on the control panel
comes on.
DRYING TIME
With this option you can set the time for the fabrics
you have to dry (cottons or synthetics) . The display
shows the set value.
Each time you press this button the time value
increases by 5 minutes.
For Cottons you can set a drying time from 10
minutes to 250 minutes (4.10), for synthetics from
10 minutes to 130 minutes (2.10).
You cannot set all time values for
different types of fabrics.
EASY IRON
The laundry is gently washed and spun to avoid any
creasing. In this way ironing is easier.
Furthermore, the appliance will perform some
additional rinses in some programmes.
11
On cotton programmes the maximum spin speed is
reduced automatically.
DELAY START
With this option you can delay the start of a
programme from 30 minutes to 20 hours.
The display shows the related indicator.
DOOR LOCKED INDICATOR DOOR
The indicator Door shows when the door can be
opened:
• The indicator is on: the door cannot be opened.
• The indicator flashes: the door is opening in
some minutes.
• The indicator is off: the door can be opened.
SETTINGS
DOOR
With this option you can prevent that the children
play with the control panel.
• To activate/deactivate this option, press Spin
and Options at the same time until the indicator
Door comes on/goes off.
You can activate this option:
• After you press Start/Pause: the options and the
programme knob are locked.
• Before you press Start/Pause: the appliance
cannot start.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press Extra rinse and Drying Time at the same time
for 6 seconds.
If you deactivate the acoustic signals,
they continue to operate when the
appliance has a malfunction.
BEFORE FIRST USE
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Put 2 litre of water in the detergent
compartment for washing phase.
This activates the drain system.
4. Put a small quantity of detergent in the
compartment for washing phase.
5. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE - WASHING ONLY
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
12
CAUTION! Make sure that no laundry
stays between the seal and the door.
There is a risk of water leakage or
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage rubber parts of
the washing machine.
USING DETERGENT AND ADDITIVES
1. Measure out the detergent and the fabric
conditioner.
2. Put the detergent
and the fabric conditioner into the compartments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
Detergent compartment for prewash phase.
Detergent compartment for
washing phase.
Compartment for liquid additives
(fabric conditioner, starch).
SETTING A PROGRAMME
1. Turn the programme knob to switch the
appliance on and set the programme:
• The indicator of the button Start/Pause
flashes.
• The display shows the programme duration.
2. If necessary, change the spin speed or add
available options. When you activate an option,
the indicator of the set option comes on.
To reset a programme or switch the machine off,
turn the programme knob to
position.
If you set something incorrect, the
display shows the message
.
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press the button Start/Pause.
• The indicator of the button Start/Pause
stops to flash and stays on.
• The programme starts, the door locks, the
indicator Door is on.
• The programme time decreases with steps
of one minute.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
STARTING A PROGRAMME WITH THE DELAY
START OPTION
1. Press the button Delay Start again and again
until the display shows the delay you want to
set. The delay start indicator comes on.
2. Press the button Start/Pause:
• The door is locked and the indicator Door is
on.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the Delay Start option before you
press the button Start/Pause. After
pressing the button Start/Pause you
can only cancel the Delay Start option.
To cancel the Delay Start option:
a. Press the button Start/Pause to set the
appliance to pause. The indicator of button
Start/Pause flashes.
b. Press the button Delay Start until the
display shows .
Press the button Start/Pause again to start
the programme immediately.
CANCELLING A RUNNING PROGRAMME
1. Turn the programme knob to position
to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Press the button Start/Pause.
The indicator flashes.
2. Change the options.
3. Press the button Start/Pause again.
The programme continues.
OPENING THE DOOR
While a programme or the Delay Start operates, the
appliance door is locked. The indicator Door is on.
13
STAND BY
Some minutes after the end of the washing
programme, if you do not deactivate the appliance,
the energy saving status activates. The energy
saving status decreases the energy consumption
when the appliance is on the standby:
• All indicators and the display go off.
• The indicator of button Start flashes slowly.
Press one of the buttons to deactivate the energy
saving status.
CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
cannot open the door.
To open the door during the first minutes of the
cycle or when the Delay Start operates:
1. Press the button Start/Pause to pause the
appliance.
2. Wait until the indicator Door goes off.
3. You can open the door.
4. Close the door and touch the button Start/
Pause again. The programme (or the Delay
Start) continues.
At the end of the programme
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
•
•
•
In the display comes on.
The indicator of the button Start/Pause goes off.
The door lock indicator Door goes off.
Turn the programme knob to position
to
deactivate the appliance.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Close the water tap.
• Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
• The indicator Rinse Hold stays on to remind you
to drain the water.
• The door lock indicator Door is on. The indicator
of button Start/Pause flashes. The door stays
locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Set a Drain or a Spin programme.
• Press the button Start/Pause. The
appliance drains the water and spins.
2. When the programme is completed and the
door lock indicator Door goes off, you can
open the door.
3. Turn the programme knob to the position
deactivate the appliance.
14
to
•
•
•
In the display comes on.
The indicator of the button Start/Pause goes off.
The door lock indicator Door goes off.
to
Turn the programme knob to position
deactivate the appliance.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Close the water tap.
• Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
• The indicator Rinse Hold stays on to remind you
to drain the water.
• The door lock indicator Door is on. The indicator
of button Start/Pause flashes. The door stays
locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Set a Drain or a Spin programme.
• Press the button Start/Pause. The
appliance drains the water and spins.
2. When the programme is completed and the
door lock indicator Door goes off, you can
open the door.
3. Turn the programme knob to the position
deactivate the appliance.
to
DAILY USE - DRYING ONLY
•
WARNING! Refer to Safety chapters.
•
If you set only 10 minutes of drying,
the appliance performs only a cooling
phase.
This appliance is an automatic washer
dryer.
DRYING SETTING
The recommended load size is 4 kg for
cottons and linen, and 2 kg for
synthetic items.
1. Load the laundry one item at a time.
2. Turn the programme dial to the programme
applicable for the items to dry (cottons or
synthetics).
To have a good drying performance
do not exceed the maximum drying
loads recommended in the user
manual. Do not set a spin speed
lower than the automatic speed of the
set programme.
TIMED DRYING
1. Press the button Drying Time again and again
to set the time value (see the «Programmes for
timed drying» table).
• Each time you press this button the time
value increases by 5 minutes.
• As the appliance calculates also the
duration of the anti-crease and the cooling
phases, the programme time will
automatically increase by some minutes.
2. Press Start/Pause button to start the
programme.
The display shows regularly a new time
value.
The indicator Door is on.
If the laundry is not sufficient dry, set again a short
drying time.
END OF THE DRYING PROGRAMME
The appliance stops automatically.
• The acoustic signals operate (if they are active).
•
•
•
In the display comes on.
The indicator of the Start/Pause button goes off.
The last minutes of the drying cycle the
appliance performs a cooling and anti-crease
phase. The door is still locked. The display show
a flashing .
When the door locked indicator Door goes off, you
can open the door.
1. Turn the programme knob to
position to
deactivate the appliance.
After some minutes from the end of the programme,
the energy saving function automatically
deactivates the appliance.
2. Remove the laundry from the appliance.
Make sure that the drum is empty.
3. Keep the door ajar, to prevent mildew and
odours.
4. Close the water tap.
DAILY USE - WASHING & DRYING
WARNING! Refer to Safety chapters.
This appliance is an automatic washer
dryer.
NON-STOP PROGRAMME (AUTOMATIC
WASHING & DRYING)
For NON-STOP programme the recommended
load size is 4 kg for cotton and 2 kg for synthetic.
CAUTION! Do not use a dosing
device/ball when carrying out a
washing and drying programme.
1. Load the laundry one item at a time.
2. Put the detergent and the additives in the
appropriate compartment.
3. Turn the programme knob to the required
programme to switch the machine on.
4. Set the available options.
15
To have a good drying performance
do not exceed the maximum drying
loads recommended in the user
manual. Do not set a spin speed
lower than the automatic speed of the
set programme.
WASHING & TIMED DRYING
To have a good drying the appliance does not let
you set a too low spin speed for the items to be
washed and dried.
1. Press the button Drying Time to set the drying
time value.
After some seconds the display shows the final
time value, that is the total duration of the washing
and drying cycles (washing + drying + anti-crease
+ cooling phases).
If you set only 10 minutes of drying
after washing, the appliance calculates
also the duration of the anti-crease
and the cooling phases.
2. Press Start/Pause button to start the
programme.
The indicator Door comes on. The door is locked.
The display shows regularly a new time value.
END OF THE PROGRAMME
The appliance stops automatically. The acoustic
signals operate (if they are active).
For more information see 'At the end of the drying
programme " of the previous chapter.
1. Turn the selector dial to the position
to
switch the machine off.
2. Remove the laundry from the appliance. Make
sure that the drum is empty.
3. Keep the door ajar, to prevent mildew and
odours.
4. Close the water tap.
FLUFF IN THE FABRICS
During the washing and/or drying phase, some
types of fabric, (sponge, sweatshirt) could release
fluff.
The released fluff could stick to the fabrics during
the next cycle.
This inconvenient increases with technical fabrics.
To prevent the fluff in your laundry, we recommend
that you:
• To do not wash dark fabrics after you washed
and dried light coloured fabrics (new sponge,
sweatshirt ) and the contrary.
• To dry this type of fabrics at open air when they
are washed the first time.
• To clean the drain filter.
• After the drying phase, clean the empty drum,
the gasket and the door with a wet cloth.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn multilayered fabrics, wool and items with
painted illustrations inside out.
• Remove hard stains with a special detergent.
• Wash and pre-treat heavy soil stains before
putting items in drum
• Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
• Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
16
•
delicate items (e.g. underwired bras, belts,
tights, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
•
•
•
•
•
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
Do not mix different types of detergents.
To help the environment, do not use more than
the correct quantity of detergent.
Obey the instructions that you find on the on
packaging of these products.
Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
DRYING HINTS
Prepare the drying cycle
•
•
•
Open the water tap.
Check if the drain hose is connected properly.
Refer to installation chapter for more
information.
For the maximum laundry load of the drying
programmes, refer to the drying programmes
table.
ITEMS NOT SUITABLE FOR DRYING
Do not set a drying programme for this
laundry:
•
•
•
•
•
•
•
•
•
•
Synthetic curtains.
Pieces of clothing with metal inserts.
Nylon stockings.
Quilts.
Bed covers.
Duvets.
Anoraks.
Sleeping bags.
Fabrics with residue of hair sprays, nail solvents
or similar.
Garments with foam-rubber or materials similar
to foam-rubber.
GARMENT LABELS
When you dry the laundry, obey the indications on
the labels of the manufacturers:
•
= The item can be tumble dried
•
= The drying cycle is at high temperature
•
•
= The drying cycle is at reduced
temperature
= The item can not be tumble dried.
DRYING CYCLE DURATION
The drying time can change depending on:
• speed of the last spin
• dryness level
• type of laundry
• weight of the load
ADDITIONAL DRYING
If, at the end of the drying programme, the laundry
is still damp, set a short drying cycle again.
WARNING! To avoid creasing and
shrinkage do not overdry the
laundry.
GENERAL TIPS
Refer to the «Drying programmes» table to find the
average drying times.
Experience will help you to dry the laundry better.
Take note of the duration of the cycles done before.
To avoid the static charge at the end of the drying
cycle:
1. Use fabric conditioner in the washing cycle.
2. Use special fabric conditioner for tumble
dryers.
When the drying programme is completed remove
the laundry promptly.
17
CARE AND CLEANING
•
WARNING! Refer to Safety chapters.
•
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all objects from the inner part.
CLEANING THE DETERGENT DISPENSER
Clean regularly the washing powder and additive
dispenser drawer.
18
•
Remove the top part of
the additive compartment to aid cleaning.
•
Make sure that all
washing powder residue is removed from
the upper and lower
part of the recess.
Use a small brush to
clean the recess.
•
•
Press the catch downwards and pull it out to
remove the drawer.
Flush it out under a
tap, to remove any
traces of accumulated
powder.
Replace the drawer and run the rinse
programme without any clothes in the drum.
CLEANING THE DRAIN FILTER
The pump should be inspected regularly and
particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during
draining phase due to objects such as safety
pins, coins and so on blocking the pump;
• a problem with water draining is detected (see
chapter 'Troubleshooting' for more details).
CAUTION! Switch the appliance off
and remove the mains plug from the
socket.
Proceed as follows:
• Unplug the appliance.
• If it is necessary, wait until the water has cooled
down.
A
B
•
•
•
•
•
•
1
•
2
•
•
•
Place a container
close to the pump (A)
to collect any spillage.
Pull out the emergency emptying hose (B),
place it in the container and remove its cap.
When no more water
comes out, unscrew
the filter.
Turn the filter anticlockwise.
Remove the filter.
Use pliers, if necessary.
When removing the
filter, always keep a
rag nearby to dry up
any water spillage.
Clean the filter under
a tap, to remove any
traces of fluff.
Remove foreign
bodes and fluff from
the filter seat and from
the pump impeller.
Check carefully
whether the pump impeller rotates (it rotates jerkily).
Never remove the filter during a washing cycle,
always wait until the appliance has finished the
cycle, and is empty.
When refitting the filter, ensure it is securely retightened so as to stop leaks and young children
being able to remove it.
CLEANING THE INLET HOSE AND THE VALVE
FILTER
If the appliance doesn't fill, take long to fill with
water, the starting button blinks or the display (if
available) shows the relevant alarm (see chapter
'Troubleshooting' for more details), check if the
water inlet filters are blocked.
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose
1
from the tap.
• Clean the filter in the
2
hose with a stiff brush.
3
•
Screw the hose back onto the tap. Make sure
the connection is tight.
• Unscrew the hose
from the machine.
• Keep a rag nearby because some water
may flow.
If it doesn’t rotate, please contact your Service
Centre.
• Put the cap back on
the emergency emptying hose and place
2
the latter back in its
seat.
• Replace the filter into
the pump, insert it
correctly into the spe1
cial guides.
•
Screw the pump cover firmly. Turn it clockwise.
CAUTION! When the appliance is in
use and depending on the set
programme there can be hot water in
the pump.
•
Clean the filter in the
valve with a stiff brush
or with the piece of
cloth.
•
Screw the hose back
to the machine and
make sure the connection is tight.
Turn on the water tap.
•
45°
20°
19
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Place the end of the emergency emptying hose
and that of the inlet hose in a bowl placed on
the floor and let water flow out of the hoses.
4. Set the Drain programme and let it operate until
the end of the cycle.
5. Turn the programme knob to
to disconnect
the appliance from the power supply.
6. Screw the water inlet hose back on and re-fit
the emergency emptying hose after having put
the cap on again.
WARNING! Make sure that the
temperature is more than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
EMERGENCY EMPTYING OUT
If the appliance does not drain the water, proceed
as follows:
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. If necessary, wait until the water has cooled
down.
4. Place a bowl on the floor and put the end of
the emergency emptying hose into the bowl.
Remove its cap.
The water should drain by gravity into the bowl.
5. When the bowl is full, put the cap back on the
emergency hose.
6. Empty the bowl. Repeat the procedure until
water stops flowing out.
7. Clean the pump if necessary as previously
described.
8. Replace the emergency emptying hose in its
seat after having plugged it.
9. Screw the water inlet hose back on.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
•
20
- The appliance does not fill with water
properly. Start the appliance again by pressing
Start/Pause button. After 10 seconds the door
will be unlocked.
•
- The appliance does not drain the water.
•
- The appliance door is open or not
closed correctly. Please check the door!
•
- The mains supply is unstable. Wait until
the mains supply is stable.
•
- No communication between electronic
elements of the appliance. Switch off and
switch on again. The programme was not
finished properly or the appliance stopped too
early. If the alarm code appears again, contact
the Authorised Service Centre.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
•
•
•
•
•
•
The appliance does not fill
with water properly.
•
•
•
•
•
•
The appliance does not
drain the water.
•
•
•
•
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on (if available).
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve
are not clogged. Refer to “Care and cleaning”.
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'.
Make sure that the drain hose is in the correct position. The hose
may be too low.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the tub.
The spin phase does not
operate or the washing cycle lasts longer than usually.
•
•
Set the spin programme.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
There is water on the floor.
•
•
Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of
it.
Make sure you have replaced the emergency emptying cap into the
filter
Make sure you have properly screwed the filter in after cleaning.
You cannot open the appliance door.
•
•
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
The appliance makes an
unusual noise.
•
Make sure the levelling of the appliance is correct. Refer to 'Installation'.
Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation'.
Add more laundry in the drum. The load may be too small.
•
•
•
•
•
21
Problem
The washing results are
not satisfactory.
Possible solution
•
•
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
You cannot set an option.
•
Make sure that you press only the wanted button(s).
The machine does not dry
or does not dry properly:
•
Make sure that you have set a suitable drying programme for your
laundry.
Make sure that you set the correct the drying time or dryness degree.
Make sure that the water tap is not turned on.
the drain filter is not clogged.
Make sure you have not overloaded the appliance.
•
•
•
•
The laundry is full of different coloured fluff:
The fabrics washed in the previous cycle released fluff of a different
colour.
• Clean the clothes with a fluff remover
• The drying phase helps to eliminate some fluff.
In case of an excessive amount of fluff in the drum, refer to section
«FLUFF IN THE FABRICS».
• Thoroughly clean the empty drum, the gasket and the door with a
wet rag.
• Perform a rinse cycle.
• Put a wool or piled fabric rag inside the drum.
• Perform a drying cycle of 10 minutes.
• Remove the old wool cloth.
Now you can wash other garments.
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
If the display shows other alarm codes. Deactivate
and activate the appliance. If the problem
continues, contact the Service.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model, PNC
and Serial Number. (Mod., Prod. No., Ser. No.)
INSTALLATION
WARNING! Refer to Safety chapters.
UNPACKING
Remove all transit bolts and packing
before you use the appliance. You are
advised to keep all transit devices so t
hat they can be refitted if the appliance
ever has to be transported again.
22
•
After removing all the
packaging, carefully
lay the appliance on
it’s back to remove
the polystyrene base
from the bottom.
•
2
•
Remove the power
supply cable and the
draining hose from the
hose holders on the
rear of the appliance.
•
Unscrew the three
bolts.
•
Slide out the relevant
plastic spacers.
•
•
1
Level the appliance by
raising or lowering the
feet.
The feet may be tight
to adjust as they incorporate a self locking nut, but the appliance MUST be level
and stable.
If necessary, check the setting with a spirit level.
Any necessary adjustment can be made with a
spanner.
• After having levelled
the appliance, tighten
the lock nuts.
• Accurate levelling prevents vibration, noise
and displacement of
the appliance during
operation.
Never place cardboard, wood or
similar materials under the appliance
to compensate for any unevenness in
the floor.
•
Remove the polystyrene block fitted on the
door seal. Pull out all
items from the drum.
WATER INLET
• The inlet hose is supplied with the appliance
and can been found inside the appliance drum.
• Do not use the hose from your previous
appliance to connect to the water supply.
This appliance must be connected toa
cold water supply.
•
•
Fill the smaller upper
hole and the two large
ones with the plastic
plug caps supplied in
the bag with the User
Manual.
•
POSITIONNING
• Install the machine on a flat hard floor. Make
sure that air circulation around the appliance is
not impeded by carpets, rugs etc.
• Check that the machine does not touch the wall
or other kitchen units.
Connect the hose
with the angled connection to the machine. Do not place
the inlet hose downwards.
45˚ • Angle the hose to the
left or right depending
35˚
on the position of your
water tap.
Set the hose correctly by loosening the ring nut.
After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.
23
•
•
Connect the hose to a
tap with a 3/4”thread.
Always use the hose
supplied with the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the tap,
you will have to purchase a new, longer hose
specially designed for this type of use.
WATER DRAINAGE
The end of the drain hose can be positioned in
three ways:
BUILDING IN
OVERVIEW
This appliance has been designed to be built into
the kitchen furniture. The recess should have the
dimensions shown in the picture below:
24
•
Hooked over the edge of a sink using the
plastic hose guide supplied with the
machine.
In this case, make sure the end cannot come
unhooked when the appliance is emptying. This
could be done by tying it to the tap with a piece
of string or attaching it to the wall.
• In a sink drain pipe branch.
This branch must be above the trap so that the
bend is at least 60 cm above the ground.
• Directly into a drain pipe at a height of not
less than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the
drainpipe must be larger than the outside
diameter of the drain hose. The drain hose must
not be kinked.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Centre
counterclockwise with a 3mm wrench. Adjust the
height and turn the nut clockwise to fix it.
600 mm
min.
596 mm
560 mm
~10mm
555 mm
min.
830 mm
818 mm
75 mm
60 mm
170 mm
100 mm
We recommend that you keep the
packaging and the transit bolts for any
movement of the appliance.
Installing anti-tiliting device
If the height of the counter is 820 mm
or lower, you cannot install the antitilting device.
PREPARATION AND ASSEMBLY OF THE
DOOR
The appliance is originally prearranged for the
assembly of a door opening from right to left (see
picture below)
Remove the screws of the top cover on the rear of
the appliance and install the anti-tilting device as
shown in the drawing.
Adjust the anti-tilting device so that the distance
from the counter is 10mm. Loosen the nut
Door
• - width 595-598 mm
• - thickness 16-22 mm
The height X depends on the height of the adjacent
furniture's base.
25
16-22 mm
X
Ø 35 mm
416
mm
A
22±1,5 mm
14 mm
595-598 mm
Hinges
To mount the hinges drill two holes (dia. 35 mm,
depth 12.5-14 mm depending on the depth of door
furniture) on the inner side of the door.
To fix the hinges to the door use the screws for
wood 1 and 2 supplied with the appliance (see
below).
B
To align the door perfectly, loosen the screw, adjust
the door and tighten the screw A again.
The appliance is prearranged for a magnetic
closure of the door. To enable a correct operation
of this device, screw the counter-magnet A (steel
disk + rubber ring) into the inner side of the door.
Its position must correspond to the magnet B on
the appliance.
Do not remove the screw C !
1
2
A
B
The distance between the holes hobs fixing centres
must be 416 mm. The distance from upper edge of
the door to the centre of the hole depends on the
adjacent furniture's dimensions.
Door mounting
To mount the door fix the hinges to the appliance
using the M5x15 screws.
Do not remove the screw B !!
The hinges can be adjusted to compensate for
possible uneven thickness of the door.
26
C
If the door has to be opened from left to right, invert
the position of the plates E, the magnet D and the
plate C.
Mount the counter-magnet D and the hinges A as
previously described.
Do not remove the screw B!
D
A
C
E
B
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
596 mm/ 818 mm/ 544 mm/ 560 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
2050 W
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply 1)
Cold water
2)
Water supply pressure
Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Maximum wash load
Cotton
7 kg
Maximum dry load
Cotton
Synthetics
4 kg
2 kg
Spin Speed
Maximum
1200 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
2) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
27
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
28
*
29
30
31
132905114-A-482017
WWW.ZANUSSI.COM/SHOP

advertisement

Related manuals

Download PDF

advertisement