Zoppas PWS6820A User Manual

User manual
Washing Machine
PWS 6820 A
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2
3
4
5
6
9
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Technical information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
10
10
12
13
15
17
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and
use causes injuries and damages. Always keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is open.
• If the appliance has a child safety device, we recommend you activate it.
• Cleaning and user maintenance shall not be made by children without supervision.
General Safety
• Before maintenance, deactivate the appliance and disconnect the mains plug
from the mains socket.
• Do not change the specification of this appliance.
2
• Obey the maximum load volume of 6 kg (refer to the “Programme chart” chapter).
• If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
• The operating water pressure (minimum and maximum) must be between 0,5
bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not be obstructed by
a carpet.
• The appliance is to be connected to the water mains using the new supplied
hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
• Remove all the packaging and the transit bolts.
• Keep the transit bolts. When you move the appliance
again you must block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the
weather.
• Obey the installation instruction supplied with the appliance.
• Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean.
• Do not install the appliance where the appliance door
can not be fully opened.
• Always be careful when you move the appliance because it is heavy. Always wear safety gloves.
• Make sure that there is air circulation between the
appliance and the floor.
• Adjust the feet to have the necessary space between
the appliance and the carpet.
Electrical connection
Warning! Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on the rating
plate agrees with the power supply. If not, contact an
electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains plug
and to the mains cable. Should the appliance power
supply cable need to be replaced, this must be carried out by our Service Centre.
• Connect the mains plug to the mains socket only at
the end of the installation. Make sure that there is access to the mains plug after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains plug with
wet hands.
• This appliance complies with the E.E.C. Directives.
Water connection
• Make sure not to cause damage to the water hoses.
• The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets
must not be reused.
• Before you connect the appliance to new pipes or
pipes not used for a long time, let the water flow until
it is clean.
• The first time you use the appliance, make sure that
there is no leakage.
Use
Warning! Risk of injury, electrical shock, fire,
burns or damage to the appliance.
• Use this appliance in a household environment.
3
• Do not change the specification of this appliance.
• Obey the safety instructions on the detergent packaging.
• Do not put flammable products or items that are wet
with flammable products in, near or on the appliance.
• Do not touch the glass of the door while a programme operates. The glass can be hot.
• Make sure that you remove all metal objects from the
laundry.
• Do not put a container to collect possible water leakage under the appliance. Contact the Service to ensure which accessories can be used.
Care and Cleaning
Warning! Risk of injury or damage to the
appliance.
• Before maintenance, deactivate the appliance and
disconnect the mains plug from the mains socket.
• Do not use water spray and steam to clean the appliance.
• Clean the appliance with a moist soft cloth. Only use
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and pets
to get closed in the appliance.
Product description
1
2
3 Control panel
4 Door handle
3
5 Internal light
6 Rating plate
4
5
6
7
1 Worktop
2 Detergent dispenser
4
7 Drain pump filter
8 Feet for the appliance level
Fixing plate kit (4055171146)
Use this special accessory, when you install the appliance on a plinth.
It prevents the movements of the appliance when it operates.
Read carefully the instructions supplied with this accessory.
You can buy it in all approved Service.
Control panel
1
Cotoni
Centrifuga
Scarico
3
2
Temperature
Normale
ECO
800
30°
Risciacqui
+Prelavaggio
Jeans
Eco
+Prelavaggio
A mano
Lana
Delicati
Speciali
Normale
+Prelavaggio
600
Candeggio
400
Lavaggio
Rapido
40°
90°
60°
Centrifuga
Opzioni
7
6
Extra
Risciacquo
Avvio/Pausa
50°
Stiro Facile Sintetici
1 Programme knob
2 Temperature knob
3 Programme phase indicators:
• A - Prewash and wash indicator
• B - Rinse and spin indicator
• C - End cycle indicator
4 Avvio/Pausa button
Centrifuga
With this option you can change the default spin speed.
The indicator of the set speed comes on.
Additional spin options:
Rinse Hold
• Set this option to prevent the laundry creases.
• The related indicator comes on.
• There is a water in the drum when the programme is
completed.
• The drum turns regularly to prevent the laundry creases.
• The door stays locked.
• You must drain the water to unlock the door.
To drain the water refer to ‘At the end of the programme’.
5
4
5 Extra Risciacquo button
6 Opzioni button:
• Candeggio option
• Lavaggio Rapido option
7 Centrifuga button:
– Rinse hold position
Temperature
Set this option to change the default temperature.
= cold water.
Indicator
The indicator of the set temperature comes on.
Candeggio
Set this option to add a bleach phase.
The bleach phase helps to remove the heavy stains.
This options is available only with cotton programmes.
Use this option only for white cotton items.
Lavaggio Rapido
With this option you can decrease the programme duration.
Use this option for items with light soil or items to refresh.
The related indicator comes on.
Extra Risciacquo
With this option you can add some rinses to a washing
programme.
5
Use this option for persons allergic to detergents and in
areas where the water is soft.
The related indicator comes on.
Wash phase indicators
When you set a programme A and B indicators come
on.
• A – Prewash and wash indicator
+
• B – Rinse and spin indicator
+
After you have started the programme the only indicator
of the running phase stays on. The machine starts to
work. The door is locked.
If you set the drain programme any light comes
on.
• C – End cycle indicator
This indicator comes on at the end of the cycle. After a
few minutes the door can be opened.
Programmes
Programme
Maximum and Minimum Temperature - Cycle Description - Maximum Spin
Speed - Maximum Fabrics Load - Type of Laundry
Detergent Compartment
Cotoni Normale
(Cold)
90° Main wash - Rinses - Spin
Maximum speed at 800 rpm
Max. load 6 kg
White and coloured cotton. Normal soil.
Cotoni Eco
90° - 40°1)
Main wash - Rinses - Spin
Maximum speed at 800 rpm
Max. load 6 kg
White cotton and coloured-fast cotton. Normal soil.
Cotoni + Prelavaggio
(Cold)
90° Main wash - Rinses - Spin
Maximum speed at 800 rpm
Max. load 6 kg
White and coloured cotton. Heavy soil.
2)
Cotoni Eco + Prelavaggio
90° - 40°
Main wash - Rinses - Spin
Maximum speed at 800 rpm
Max. load 6 kg
White and coloured-fast cotton. Heavy soil.
2)
Sintetici
(Cold)
60° Main wash - Rinses - Spin
Maximum spin speed at 800 rpm
Max. load 3 kg
Synthetic or mixed fabrics: underwear, coloured garments, non-shrink shirts, blouses.
6
Programme
Maximum and Minimum Temperature - Cycle Description - Maximum Spin
Speed - Maximum Fabrics Load - Type of Laundry
Sintetici + Prelavaggio
(Cold)
60° Main wash - Rinses - Spin
Maximum spin speed at 800 rpm
Max. load 3 kg
Synthetic or mixed fabrics . Heavy soil.
Detergent Compartment
2)
Stiro Facile
(Cold)
60° Main wash - Rinses - Spin
Maximum spin speed at 800 rpm
Max. load 1 kg
Synthetic fabric items. Normal soil. It prevents the laundry creases.
Delicati
(Cold)
40° Main wash - Rinses - Spin
Maximum speed at 600 rpm
Max. load kg 3
Delicate fabrics: acrylics, viscose, polyester.
Lana
(Cold)
40° Main wash - Rinses - Spin
Maximum speed at 800 rpm
Max. load 2 kg
For machine washable wool as well as for hand washable woollens and delicate fabrics3) .
A mano
(Cold)
40° Main wash - Rinses - Spin
Maximum spin speed at 800 rpm
Max. load 2 kg
Delicate fabrics with «hand washing» care symbol.
Jeans
(Cold)
60° Main wash - Rinses - Spin
Maximum speed at 800 rpm
Max. load 3 kg
Pants, shirts or jackets in denim and also jersey realized with hi-tech materials (the
Extra Rinse option will be activated automatically).
2)
7
Programme
Maximum and Minimum Temperature - Cycle Description - Maximum Spin
Speed - Maximum Fabrics Load - Type of Laundry
Detergent Compartment
Risciacqui
Rinses - Spin
Maximum speed at 800 rpm
Max. load 6 kg
For cotton garments washed by hand. The machine performs some rinses and a final
long spin. If needed, reduce the spin speed.
Scarico
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in programmes with the option selected,
which ends with water left in the tub.
Centrifuga
Drain - Long spin
Maximum speed at 800 rpm
Max. load 6 kg
Separate spin for hand washed garments. Also, after programmes with water left in
the tub, if needed, reduce the spin speed to adapt it to the fabrics to be spun.
= OFF
For cancelling a running programme or to switch the machine off .
1) Standard programmes for the Energy Label consumption values. The programme Cotoni Eco at 60°C
and the
programme Cotoni Eco at 40°C
are respectively the “standard 60 °C cotton programme” and the “standard 40 °C cotton
programme”. They are the most efficient programmes in terms of combined energy and water consumptions for washing
normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected programme.
The time of the washing programme is extended. For cotton economy programmes you can set only the Extra Quick duration.
2) If you use liquid detergents, set a programme without PREWASH.
3) A single or bulky item may cause imbalance. If the appliance doesn’t perform the final spin phase, add more items, redistribute
the load manually and then set the spinning programme.
8
Candeggio
Extra Risciacquo
Programme
Lavaggio Rapido1)
Centrifuga
Programme options compatibility
∎
∎
Cottons
∎
∎
∎
Cotoni Eco
∎
∎
∎
∎
Cotoni + Prelavaggio
∎
∎
∎
∎
Sintetici
∎
∎
∎
∎
Sintetici + Prelavaggio
∎
∎
Stiro Facile
∎
∎
∎
∎
∎
Delicati
Lana
∎
∎
A mano
∎
∎
Jeans
∎
∎
Risciacqui
∎
∎
∎
∎
∎
∎
∎
Scarico
∎
Centrifuga
1) When you set the Lavaggio Rapido option, we recommend that you decrease the quantity of the laundry. It is possible to keep
the full load but the washing results can be unsatisfactory. We recommend to load: 3 kg for cotton, and 1.5 kg for synthetics and
delicates.
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature.
Programmes
Load
(Kg)
Energy consumption (kWh)
Water consumption (litre)
Approximate
programme duration (minutes)
Remaining
moisture (%)1)
Cottons 60 °C
6
1.00
56
146
66
Cottons 40 °C
6
0.75
56
145
66
Synthetics 40 °C
3
0.47
45
127
37
Delicates 40 °C
3
0.65
62
100
37
Wool/Hand wash 30
°C
2
0.25
55
56
37
Standard cotton programmes
Standard 60 °C cotton
6
1.01
49
175
66
Standard 60 °C cotton
3
0.83
40
150
66
Standard 40 °C cotton
3
0.66
40
145
66
1) At the end of spin phase.
Off Mode (W)
Left On Mode (W)
0.10
0.98
9
Off Mode (W)
Left On Mode (W)
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC.
Before first use
1.
2.
Put 2 litre of water in the detergent compartment
for washing phase. This activates the drain system.
Put a small quantity of detergent in the compartment for washing phase.
3.
Set and start a programme for cotton at the highest
temperature without laundry. This removes all possible dirt from the drum and the tub.
Daily use
1.
2.
3.
4.
5.
Open the water tap.
Connect the mains plug to the mains socket.
Put the laundry in the appliance.
Use the correct quantity of detergent and additives.
Set and start the correct programme for the type of
laundry and soil.
Using detergent and additives
• Measure out the detergent and the fabric
conditioner.
• Carefully close the detergent drawer.
Loading the laundry
1.
2.
3.
Open the appliance door.
Put the laundry in the drum, one item at a time.
Shake the items before you put them in the appliance. Make sure not to put too much laundry
in the drum.
Close the door.
Caution! Make
sure that no laundry
stays between the seal
and the door. There is a
risk of water leakage or
damage to the laundry.
Detergent compartment for prewash
phase.
Detergent compartment for washing
phase.
Compartment for liquid additives (fabric
conditioner, starch).
Compartment for bleach agent. Pour it
before the start of the washing phase.
We suggest you to use it only with white
cotton items.
Flap for powder or liquid detergent.
10
Interrupting a programme and changing the options
You can change only some options before they operate.
1. Press Avvio/Pausa. The indicator flashes.
2. Change the options.
3. Press Avvio/Pausa again. The programme continues.
Liquid or powder detergent
2.
1.
A
MAX
3.
4.
B
Cancelling a programme
1. Turn the programme knob to
to cancel the programme and to deactivate the appliance.
2. Turn the programme knob again to activate the appliance. Now, you can set a new washing programme.
The appliance does not drain the water.
Opening the door
While a programme operates, the appliance door is
locked.
• Position A for powder detergent (factory setting).
• Position B for liquid detergent.
When you use the liquid detergent:
– Do not use gelatinous or thick liquid detergents.
– Do not put more liquid then the maximum
level.
– Do not set the prewash phase.
– Do not set the delay start.
Setting a programme
1. Turn the programme knob and set the programme.
2. Set the temperature.
3. The Avvio/Pausa indicator flashes.
4. If necessary, change the spin speed or add available functions.
When you press the relevant button, the indicator
of the set function comes on.
Starting a programme
Press Avvio/Pausa:
• The Avvio/Pausa indicator stops to flash and the indi+
is on.
cator
• The programme starts and the door locks.
Caution! If the temperature and level of the water
in the drum are too high, you cannot open the
door.
Open the appliance door when the delay start
operates:
1. Press Avvio/Pausa to pause the appliance.
2. Wait some minutes until the door unlocks.
3. You can open the door.
4. Close the door and press Avvio/Pausa again.
Open the appliance door when the programme
operates:
1. Turn the programme knob to
to deactivate the
appliance.
2. Wait for some minutes and then open the appliance door.
3. Close the appliance door.
4. Set the programme again.
At the end of the programme
The appliance stops automatically.
• The Avvio/Pausa indicator goes off.
• The End indicator
is on.
1.
2.
to deactivate the
Turn the programme knob to
appliance.
Remove the laundry from the appliance. Make sure
that the drum is empty.
11
3.
4.
Keep the door ajar, to prevent the mildew and
odours.
Close the water tap.
The washing programme is completed, but there is
water in the drum:
– The drum turns regularly to prevent the creases in
the laundry.
– The door stays locked and the Avvio/Pausa indicator
flashes.
– You must drain the water before you can open the
door.
To drain the water:
1. Set the Scarico or the Centrifuga programme.
2. Press Avvio/Pausa. The appliance drains the water
and/or spins.
3. When the programme is completed:
– The Avvio/Pausa indicator goes off and the indiis on.
cator
– After some minutes you can open the door.
4.
Turn the programme knob
ance.
deactivate the appli-
Stand-by
Some minutes after the end of the washing programme,
if you do not deactivate the appliance, the energy saving
status activates.
The energy saving status decreases the energy consumption when the appliance is on the stand by.
• All indicators go off.
• The Avvio/Pausa indicator flashes slowly
• Press one of the options to deactivate the energy
saving status.
Hints and tips
The laundry load
• Divide the laundry in: white, coloured, synthetics, delicates and wool.
• Obey the washing instructions that are on the laundry
care labels.
• Do not wash together white and coloured items.
• Some coloured items can discolour with the first
wash. We recommend that you wash them separately for the first times.
• Button up pillowcases, close zippers, hooks and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool and items
with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil stains.
• Be careful with the curtains. Remove the hooks or
put the curtains in a washing bag or pillowcase.
• Do not wash in the appliance :
– Laundry without hems or with cuts
– Underwired bras.
– Use a washing bag to wash small items.
• A very small load can cause balance problems with
the spin phase. If this occurs, adjust manually the
items in the tub and start the spin phase again.
12
Stubborn stains
For some stains, water and detergent is not sufficient.
We recommend that you remove these stains before
you put the items in the appliance.
Special stain removers are available. Use the special
stain remover that is applicable to the type of stain and
fabric.
Detergents and additives
• Only use detergents and additives specially made for
washing machines.
• Do not mix different types of detergents.
• To help the environment, do not use more than the
correct quantity of detergent.
• Obey the instructions that you find on the on packaging of these products.
• Use the correct products for the type and colour of
the fabric, the programme temperature and the level
of soil.
• If you use liquid detergents, do not set the prewash
phase.
• If your appliance has not the detergent dispenser
with the flap device, add the liquid detergents with a
dosing ball.
Water hardness
If the water hardness in your area is high or moderate,
we recommend that you use a water softener for wash-
ing machines. In areas where the water hardness is soft
it is not necessary to use a water softener.
To know the water hardness in your area, contact your
local water authority.
Obey the instructions that you find on the packaging of
the products.
Care and cleaning
Warning!
Door seal
Disconnect the appliance from the mains supply before
you clean it.
Regularly examine the
seal and remove all objects from the inner part.
External cleaning
Clean the appliance only with soap and warm water.
Fully dry all the surfaces.
Caution! Do not use alcohol, solvents or chemical
products.
Descaling
The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales.
Use a special product made for washing machines.
Obey the instructions that you find on the packaging of
the manufacturer.
Do this separately from the laundry wash.
Maintenance wash
With the low temperature programmes it is possible that
some detergent stays in the drum. Make regularly a
maintenance wash. To do this:
• Empty the laundry from the drum.
• Set the hottest cotton wash programme
• Use a correct quantity of powder detergent with biological properties.
After each wash, keep the door open for a while to prevent mould and to let unpleasant smells go out.
Drum
Regularly examine the drum to prevent limescale and
rust particles.
Only use special products to remove rust particles from
the drum.
To do this:
• Clean the drum with special product for stainless
steel.
• Start a short programme for cotton at the maximum
temperature with a small quantity of detergent.
Cleaning the detergent dispenser
2.
1.
1
2
3.
4.
Cleaning the inlet hose filter and the valve filter
It could be necessary to clean the filters when:
• The appliance does not fill with water.
• The appliance fills with the water for a long time.
• The indicator of Avvio/Pausa flashes and the display
shows the related alarm. Refer to 'Troubleshooting'.
Warning! Disconnect the mains plug from the
mains socket.
13
1.
2.
2.
35°
45°
3.
1.
Cleaning the drain pump
3.
Regularly examine the drain pump and make sure
that it is clean.
Clean the pump if:
• The appliance does not drain the water.
• The drum cannot turn.
• The appliance makes an unusual noise because of
the blockage of the drain pump.
• The display shows an alarm code because of the
problem with water drain.
1.
2.
14
4.
Warning!
Disconnect the mains plug from the mains socket.
Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in
the appliance is hot. The water must be cold before
you clean the drain pump.
1
5.
2
If this occurs, do steps (1) through (8) of 'Cleaning the
drain filter'.
If necessary, clean the pump.
When you drain the water with the emergency drain procedure, you must activate again the drain system:
1. Put 2 litres of water in the main wash compartment
of the detergent dispenser.
2. Start the programme to drain the water.
6.
7.
1
2
8.
Frost precautions
If the appliance is installed in an area where the temperature can be less than 0° C, remove the remaining water from the inlet hose and the drain pump.
1. Disconnect the mains plug from the mains socket.
2. Close the water tap.
3. Remove the water inlet hose.
4. Put the two ends of the inlet hose in a container
and let the water flow out of the hose.
5. Empty the drain pump. Refer to the emergency
drain procedure.
6. When the drain pump is empty, install the inlet
hose again.
Warning! Make sure that the temperature is more
than 0 °C before you use the appliance again.
The manufacturer is not responsible for damages
caused by low temperatures.
Emergency drain
Because of a malfunction, the appliance cannot drain
the water.
Troubleshooting
The start of the appliance does not occur or the appliance stops during operation. First try to find a solution to
the problem (refer to the table). If not, contact the Service.
During appliance operation it is possible that the red indicator of Avvio/Pausa flashes to show that the appliance does not operate.
It is possible to recognize the problem by the number of
the Avvio/Pausa indicator flashes : press simultaneously
the buttons Extra Risciacquo and Avvio/Pausa for some
seconds.
The red indicator of Avvio/Pausa flashes for a short time
(do not consider the green flash) :
• 4 flashes = ‘The washing machine does not start’,
do the checks indicated in the table ‘Possible solution’ below and start again the programme.
• 1 flash = ’The appliance does not fill with water’,
do the checks indicated in the table ‘Possible solution’ below and start again the programme.
• 2 flashes = ’The appliance does not drain the water and/or does not spin’, do the checks indicated in
the table ‘Possible solution’ below and start again the
programme.
Warning! Deactivate the appliance before you do
the checks.
15
Problem
The appliance does not
start.
Possible solution
Make sure that the mains plug is connected in the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the household fuse box.
Make sure that the Avvio/Pausa has been pressed.
Make sure that the programme knob is in the correct position.
The appliance does not
fill with water.
Make sure that the water tap is opened.
Make sure that the pressure of the water supply is not too low. For this information,
contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve are not clogged.
Refer to 'Care and cleaning'.
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
The appliance does not
drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the water drain hose has no kinks or bends.
Make sure that the connection of the water drain hose is correct.
Set the drain programme if you set a programme without the drain phase.
Set the drain programme if you set an option which ends with water in the drum.
If above mentioned solutions do not help, contact the Service (as the filter of the drain
pump may be clogged).
The spin phase does not
operate or the washing
cycle lasts longer than
usually.
Adjust manually the items in the drum and start the spin phase again. This problem
may be caused by balance problems.
Set the spin programme.
Set the drain programme if you set an option which ends with water in the drum.
If above mentioned solutions do not help, contact the Service (as the filter of the drain
pump may be clogged).
There is water on the
floor.
Make sure that the couplings of the water hoses are tight and there are no water leakages.
Make sure that the water inlet hose and the water drain hose has no damages.
Make sure you use the correct detergent and the correct quantity of it.
You cannot open the appliance door.
16
Make sure that the washing programme is finished.
Problem
Possible solution
Set the drain or the spin programme if there is water in the drum.
The appliance makes an
unusual noise.
Make sure that the levelling of the appliance is correct. Refer to 'Installation instruction'.
Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation instruction'.
Add more laundry in the drum. The load may be too small.
The appliance fills with
water and drain immediately.
Make sure that the drain hose is in the correct position. The end of the hose may be is
too low. Refer to 'Installation instruction'.
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
After the check, activate the appliance. The programme
continues from the point of interruption.
If the problem occurs again, contact the Service.
Service
We recommend the use of original spare parts.
When contacting the Service, make sure that these data
are available. You can find the information on the rating
plate: model (Mod.), PNC (Prod.No.), Serial number
(Ser.No.).
Technical information
Dimensions
Width / Height / Depth
Total depth
Electrical connection:
Voltage
Overall power
Fuse
Frequency
Level of protection against ingress of solid particles and moisture ensured
by the protective cover, except where the low voltage equipment has no
protection against moisture
Water supply pressure
600 / 850 / 440 mm
490 mm
220-230 V
2000 W
10 A
50 Hz
IPX4
Minimum
0,5 bar (0,05 MPa)
Maximum
8 bar (0,8 MPa)
Cold water
Water supply 1)
Maximum load
Cotton
Spin speed
Maximum
6 kg
800 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
17
18
19
www.electrolux.com/shop
1329164900-A-062013