Tricity Bendix AW1400W Installation instructions

132994650.qxd
6/25/02
10:18 AM
Pagina
1
(Nero/Process Black pellicola)
OPERATING & INSTALLATION
INSTRUCTIONS
WASHING MACHINE
AW 1200 W
AW 1400 W
132994650
132994650.qxd
6/25/02
10:18 AM
Pagina
2
(Nero/Process Black pellicola)
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
Installation
●
●
●
●
●
●
●
Use
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
●
●
●
●
●
●
Child Safety
●
●
●
●
●
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Pets and children have been known to climb into
washing machines. Please check your drum before
use.
The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children’s
reach.
●
●
●
●
2
Always unplug the appliance and turn off the water
supply after use.
Do not overload the appliance. See relevant section
in the instruction book.
Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the clothes.
Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.
Leave the porthole door slightly ajar between washes
to preserve the door seal.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre. Always insist on genuine Tricity Bendix
spare parts.
132994650.qxd
6/25/02
10:18 AM
Pagina
3
(Nero/Process Black pellicola)
Contents
Maintenance and Cleaning
For the User
Important Safety Information
Your New Washing Machine
Description of the Appliance
Door locked light
Detergent dispenser drawer
Child Safety Feature
The Control Panel
Programme information
Descaling
After each wash
Maintenance Wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the pump
Cleaning the water inlet filter
Emergency emptying out
The dangers of freezing
2
4
5
5
5
5
6-7
7
Something Not Working
Service and Spare Parts
Guarantee Conditions
Operating sequence
8-11
Washing 4.5 kg of white cotton at 95°C
8
Load the laundry
8
Measure out the detergent
8
Measure out the fabric softener
8
Select the required programme
8
Select spin speed reduction or no spin option
8
Select the required option
8
Start the programme
9
Altering a programme
9
Interrupting a programme
9
Cancelling a programme
9
Opening the door after the programme has started
9
At the end of the programme
9
Washing 2 kg of mixed fabrics at 50°C
10
Load the laundry
10
Measure out the detergent and the fabric softener
10
Select the required programme
10
Select spin speed reduction or no spin option
10
Select the required option(s)
10
Start the programme
10
At the end of the programme
11
Washing Hints
Which detergent?....
And in which form?
Wash Care Symbols
Washing Programmes
17-18
17
17
17
17
17
17
17
18
18
18
19-20
20
21
For the Installer
Installation Instructions
Technical Specifications
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connection
12-13
13
13
14
15-16
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
22
22
24
24
24
24-25
25
25
25
26
132994650.qxd
6/25/02
10:19 AM
Pagina
4
(Nero/Process Black pellicola)
Your New Washing Machine
Your new washing machine meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption.
●
●
●
●
The programme selector dial combines the
function of programme and temperature selection,
making it easier to set the programme.
The programme progress display shows the
washing phase and the end of the programme .
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
The ECO VALVE allows total use of detergent and
reduces water consumption so saving energy.
In the interest
of the environment
●
●
●
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
● Adjust the quantity of detergent according to the
hardness of your water supply, the amount of
laundry and the degree of soiling.
● A programme without prewash is sufficient for
normally soiled laundry.
● The machine works more economically if it is fully
loaded.
● With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature, so saving energy.
●
Materials marked with the symbol
are
recyclable.
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed "Something
Not Working".
4
132994650.qxd
6/25/02
10:19 AM
Pagina
5
(Nero/Process Black pellicola)
Description of the Appliance
3
1
1Detergent dispenser drawer
2 Programme guide
3 Control panel
4 Door opening handle
5 Drain pump
6 Adjustable feet
1200 rpm
PROGRAMME
ELECTRONIC
COTTONS - LINENS
WHITES
ECO WASH
60°
FAST COLOURS
NON FAST COLOURS
SYNTHETICS
MIXED FABRICS
MIXED FABRICS
MIXED FABRICS
95°
60°
40°
60°
50°
40°
1
2
3
4
5
6
7
DELICATE FABRICS
DELICATES
40°
DELICATES
30°
WOOL
30°
COLD WASH
QUICK AND COOL
Rinses
Drain
Spin
no spin
1
15
spin
reduction
8
9
10
11
12
13
14
15
2
14
prewash
half
load
rinse
hold
start
pause
wash
rinses
spin
end
ADVANCED
ECO
SHOWER SYSTEM
door
3
13
4
12
11
5
6
10
9
8
7
AW 1200 W
2
4
5
6
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0069
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
P1131
5
132994650.qxd
6/25/02
10:19 AM
Pagina
6
(Nero/Process Black pellicola)
The Control Panel
1200 rpm
PROGRAMME
ELECTRONIC
COTTONS - LINENS
WHITES
ECO WASH
60°
FAST COLOURS
NON FAST COLOURS
SYNTHETICS
MIXED FABRICS
MIXED FABRICS
MIXED FABRICS
95°
60°
40°
60°
50°
40°
1
2
3
4
5
6
7
DELICATE FABRICS
DELICATES
40°
DELICATES
30°
WOOL
30°
COLD WASH
QUICK AND COOL
Rinses
Drain
Spin
8
9
10
11
12
13
14
15
spin
reduction
no spin
2
14
prewash
half
load
rinse
hold
start
pause
wash
rinses
spin
end
door
ADVANCED
ECO
3
13
4
12
11
5
6
10
SHOWER SYSTEM
1
1
15
9
2 3 4 5 6 7
8
7
AW 1200 W
8
1 Detergent dispenser drawer
4 Half Load button
Programme Option buttons
Select this button to reduce water consumption on the
rinse cycle when washing a smaller load of cottons or
linens (maximum load size = 2.25 kg).
The machine will perform 2 rinses instead of 3.
Depending on the programme, different functions can
be combined. These must be selected after choosing the
desired programme and before depressing the “start
pause” button.
When these buttons are pressed, the corresponding pilot
lights come on. When they are pressed again, the pilot
lights go out.
If an incorrect option is selected, the corresponding
pilot light flashes for about 2 seconds.
5 Rinse Hold button
When selecting this option the water of the last rinse is
not emptied out, to prevent the fabrics from creasing.
At the end of the programme the pilot lights “door” and
“end” illuminate. To drain water, proceed as follows:
● turn the programme selector dial to position “O”;
● select programme 14 (drain) or 15 (spin). In this
case reduce the spin speed by means of the relevant
button to adapt it to the fabrics to be spun.
● press “start pause” button.
2 Spin button
By depressing this button you can reduce the final and
the intermediate spin speeds or select the “no spin”
option:
● “spin reduction”: by selecting this option the speed
will be reduced as follows:
Cotton: from 1400 to 700 r.p.m. and from 1200 to
600 r.p.m.
Synthetics and wool: from 900 to 450 r.p.m.
Delicates: from 700 to 450 r.p.m.
●
6 Start Pause button
After having selected the required programme, press
this button to start the machine; the corresponding pilot
light stops flashing.
To interrupt a programme which is running, depress the
“start pause” button: the corresponding pilot light starts
to flash.
To restart the programme from the point at which it was
interrupted, press the “start pause” button again.
“no spin”: by selecting this option all the spinning
phases are suppressed. To be used for extremely
delicate items.
The machine will add 3 rinses on cotton
programmes and 1 rinse on synthetic programmes.
7 Programme progress display
3 Prewash button
By selecting the wash programme, the pilot lights
corresponding to the various phases making up the
programme come on.
Select this option if you wish your laundry to be
prewashed before the main wash (not available for
wool).
The prewash ends with a short spin in programmes for
cotton and synthetic fabrics, whereas in the programme
for delicate fabrics the water is only drained.
6
132994650.qxd
6/25/02
10:19 AM
Pagina
7
(Nero/Process Black pellicola)
ATTENTION!
If you turn the programme selector dial to an other
programme when the machine is working, the lights of
the programme progress display start to flash. The
machine will not perform the new selected programme.
wash
rinses
spin
end
door
Programme information
After the machine has started, only the running phase
pilot light stays on.
When the pilot light “wash” comes on this means that
the machine is performing the washing phase. If you
have selected the “prewash” function, this light will be
on during the prewash phase too.
The “end” pilot light flashes in the event of operating
problems:
- 4 flashes = the door has not been closed
- 2 flashes = the machine does not empty
- 1 flash = the machine does not fill
To eliminate the problem, see paragraph “Something not
working”.
The “door” pilot light indicates if the door can be
opened:
- light on: the door cannot be opened
- light off: the door can be opened
- flashing light: the door is opening
It stays on during the whole programme indicating that
the door is locked.
When the light goes out, the door can be opened (see
page 9).
10 = Wool
The wool wash cycle of this machine has been approved
by Woolmark for the washing of machine washable
Woolmark products provided that the garments are
washed according to the instructions on the garment
label and those issued by the manufacturer of this
washing machine. M9604.
12 = Quick and Cool
This is a complete programme to be used for lightly
soiled laundry or for laundry which needs freshening up
(not available for wool).
Max load: 2. kg .
Washing temperature: 30°C
Number of rinses: 2 .
Programme duration: 30 minutes.
Short spin at 700 r.p.m max.
13 = Rinses
With this programme it is possible to rinse and spin
garments which have been washed by hand.
The machine performs 3 rinses, followed by a final
short spin at the maximum speed that can be reduced
lected by means of the relevant button.
8 Programme selector dial
The selector dial is divided into 2 sections: red and
black.
14 = Drain
PROGRAMME
1
15
2
14
For emptying out the water of the last rinse in programmes
with the “rinse hold” option.
Turn first the programme selector dial to O, then select
drain programme 14 and depress the “start pause” button.
3
13
4
12
11
5
6
10
9
8
7
15 = Spin
The selector dial can be turned either clockwise or
anticlockwise.
Position O corresponds to to Reset programme /
Switching OFF of the machine.
Separate short spin for hand washed garments and after
programmes with “rinse hold” option. Before selecting
this programme the selector dial must be turned to “O”.
You can choose the speed by means of the relevant
button to adapt it to the fabrics to be spun.
7
132994650.qxd
6/25/02
10:19 AM
Pagina
8
(Nero/Process Black pellicola)
Operating Sequence
3. Select the required programme
Before the first wash, we recommend that you pour 2
litres of water into the main wash compartment
of
the detergent drawer in order to activate the ECO valve.
Then run a cotton cycle at 60°C, without any laundry in
the machine, to remove any manufacturing residue from
the drum and tub.
Pour 1/2 a measure of detergent into the dispenser
drawer and start the machine.
Turn the programme selector dial to the programme 1.
The light “start pause” starts to flash. The pilot lights
corresponding to the various phases making up the
programme come on.
PROGRAMME
1
15
2
14
3
13
WASHING 4.5 KG OF WHITE COTTON AT 95°C
Suppose you have 4.5 kg of heavy soiled laundry to
wash. It is white cotton and is suitable for high
temperature washing.
4
12
11
5
6
10
9
8
7
4. Select “spin reduction” or
no spin” option
1. Load the laundry
Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
Press the option button repeatedly, to select the desired
option. The relevant light illuminates.
spin
reduction
no spin
P0004
5. Select the required option
2. Measure out the detergent
and the fabric softener
Select “prewash” or “rinse hold” option if required, the
corresponding light illuminates.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required, pour it
into the main wash compartment
and into the
compartment marked
if you have selected the
“prewash” option.
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer). Close the drawer gently.
C0070
prewash
C0071
8
half
load
rinse
hold
132994650.qxd
6/25/02
10:19 AM
Pagina
9
(Nero/Process Black pellicola)
6. Start the programme
10.Opening the door after the
programme has started
Before starting up the machine check that:
● the appliance is plugged in
● the water supply tap is turned on
● the drain hose is correctly and securely positioned
● the door and the detergent dispenser drawer are
closed.
To start the selected programme, press
the “start pause” button; the corresponding light stops
flashing.
Only the “wash” light stays on.
The “door” light comes on to indicate that the door is
locked. The machine starts operating.
First set the machine to pause by pressing the “start
pause” button. If the “door” light flashes and after 2
minutes goes off, the door can be opened.
If the “door” light doesn’t flash, this means that the
machine is already heating, that the water level is above
the bottom edge of the door or that the drum is turning.
In this case the door can not be opened.
If you cannot open the door but you need to open it you
have to switch the machine off by turning the selector
dial to “O”. After about 2 minutes the door can be
opened (pay attention to the water level and
temperature!).
11. At the end of the programme
The machine stops automatically.
If the “rinse hold” option has been selected, the phase
light “end” and “door” light are on to indicate that the
water must be emptied out before opening the door.
To do this first turn the programme selector dial to “O”
and then to drain programme 14 or spin programme 15.
The door can only be opened after the light of the
porthole has gone out.
Release of the lock is also indicated by the coming on of
the “end” light.
Turn the programme selector dial to “O” to switch the
machine off.
Remove the laundry from the drum and carefully check
that the drum is empty.
If you do not intend to carry out another wash, close the
water tap. Leave the door open to prevent the formation
of mildew and unpleasant smells.
start
pause
7. Altering a programme
You can alter the programme before it starts.
When the programme has started, you can only reset it
by turning the programme selector dial to O and then
you can select the new programme.
The washing water remains in the tub.
Start the new programme by depressing the
“start pause” button.
8. Interrupting a programme
Depress the “start pause” button to interrupt a
programme which is running, the corresponding light starts
to flash. Depress the button again to restart the programme.
9.Cancelling a programme
Turn the selector dial to O to cancel a programme which
is running. Now you can select a new programme.
9
132994650.qxd
6/25/02
10:19 AM
Pagina
10
(Nero/Process Black pellicola)
4. Select the required
programme
WASHING 2 KG OF MIXED FABRICS AT 50°C
Suppose you have 2 kg of lightly soiled mixed fabrics to
wash. They are rather delicate fabrics and should not be
washed at a high temperature.
Turn the programme selector dial to the programme 6.
The “start pause” light starts to flash. The pilot lights
corresponding to the various phases making up the
programme come on.
1. Load the laundry
Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
PROGRAMME
1
15
2
14
3
13
4
12
11
5
6
10
9
8
7
5. Select “spin reduction” or
no spin” option
P0004
Press the option button repeatedly, to select the desired
option. The relevant light illuminates.
2. Measure out the detergent
spin
reduction
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment
and into the
compartment marked
if you have selected the
“prewash” option.
no spin
6. Select the required option
Select “prewash” or “rinse hold” option if required, the
corresponding light illuminates.
C0070
3. Measure out the fabric
softener
prewash
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.
half
load
rinse
hold
7. Start the programme
Before starting up the machine check that:
● the appliance is plugged in
● the water supply tap is turned on
● the drain hose is correctly and securely positioned
● the door and the detergent dispenser drawer are
closed.
C0071
10
132994650.qxd
6/25/02
10:19 AM
Pagina
11
(Nero/Process Black pellicola)
To start the selected programme, press the “start pause”
button; the corresponding light stops flashing.
Only the “wash” pilot light stays on.
The “door” light comes on to indicate that the door is
locked.
The machine starts operating.
start
pause
8. At the end
of the programme
The machine stops automatically.
If the “rinse hold” option has been selected, the phase
light “end” and the “door’ light are on to indicate that
the water must be emptied out before opening the door.
To do this first turn the programme selector dial to “O”
and then to drain programme 14 or spin programme 15.
In this case reduce the spin speed by means of the
relevant button to adapt it to the fabrics to be spun.
The door can only be opened after the relevant pilot light
on the control panel has gone out.
Release of the lock is also indicated by the coming on of
the “end” light.
Turn the programme selector dial to “O” to switch the
machine off.
Remove the laundry from the drum and carefully check
that the drum is empty.
If you do not intend to carry out another wash, close the
water tap.
Leave the door open to prevent the formation of mildew
and unpleasant smells.
11
132994650.qxd
6/25/02
10:19 AM
Pagina
12
(Nero/Process Black pellicola)
Washing Hints
Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.
●
The average weights of the most common items are
listed below as a guide:
●
●
1000g = 1 kg
Sheet
700-1000 g
Pillow case
100-200 g
Tablecloth
400-500 g
Serviette
50-100 g
Tea towel
70-120 g
Linen hand towel
100-150 g
Towelling hand towel
150-250 g
Towelling bath towel
700-1000 g
Bath robe
200-300 g
Apron
150-200 g
●
●
●
●
●
●
●
●
●
●
●
●
1000-1500 g
Man’s shirt
●
●
●
Load the laundry loosely alternating large items with
small ones.
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
Use the correct quantities of detergent.
12
For wool, use gentle detergent only in small
quantities.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special presoak product or biological detergent.
Only wool marked “Pure New Wool - washable,
preshrunk” can be washed in the machine using the
wool programme; other types of wool should be
washed in HANDWASH programme.
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Once you have finished using the machine, you are
advised to unplug it and turn off the water tap.
132994650.qxd
6/25/02
10:19 AM
Pagina
13
(Nero/Process Black pellicola)
Which detergent?....
And in which form?
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.
TRADITIONAL POWDERS
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
TRADITIONAL LIQUIDS
WHITES
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
, start
the machine immediately upon placing the detergent in
the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
NON BIOLOGICAL
If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.
COLOUREDS
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.
* If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
DELICATE ITEMS
FABRIC CONDITIONERS
When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.
These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
marked with the symbol .
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
LAUNDRY BLEACH
For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.
Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.
13
132994650.qxd
6/25/02
10:19 AM
Pagina
14
(Nero/Process Black pellicola)
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
95
Normal (Maximum)
White Cotton or Linen
without Special Finishes
60
Normal (Maximum)
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
50
Reduced (Medium)
Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.
40
Normal (Maximum)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
Reduced (Medium)
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
40
Much Reduced (Minimum)
Hand wash only
FABRIC
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot iron
Cotton, Linen, Viscose
Warm iron
Polyester mixtures, Wool
Cool iron
Acrylic, Nylon, Polyester
DRY CLEANING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
with high heat setting
with low heat setting
May be tumble dried
X
A cross through any symbol means «DO NOT»
Important Notes
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using
14
132994650.qxd
6/25/02
10:19 AM
Pagina
15
(Nero/Process Black pellicola)
Washing Programmes
Programmes for cotton and linen
Wash programme/
Washing symbol
Degree of soil
and type of laundry
Programme
dial position
WHITES
For heavy soiled cotton
items.
ECO WASH
White cotton, for
example normally soiled
work garments, sheets,
household linen,
underwear, towels.
FAST
COLOUREDS
Fast coloured cotton or
linen fabrics, normally
soiled, shirts,
underwear, towels.
NON FAST
COLOUREDS
Non fast coloured
cotton or linen fabrics,
normally soiled, shirts,
blouses, underwear.
4
RESET / OFF
For cancelling the wash
programme which is
running and for
switching the machine
off
O
1
(*)
2
3
Description
Possible
options
Max. Progr.
time
load mins.
Wash at 95°C
3 rinses
Long spin
PREWASH
HALF LOAD
RINSE HOLD
SPIN RED.
NO SPIN
4.5 kg
140
Wash at 60 °C
3 rinses
Long spin
PREWASH
HALF LOAD
RINSE HOLD
SPIN RED.
NO SPIN
4.5 kg
120
Wash at 60 °C
3 rinses
Long spin
PREWASH
HALF LOAD
RINSE HOLD
SPIN RED.
NO SPIN
4.5 kg
115
Wash at 40 °C
3 rinses
Long spin
PREWASH
HALF LOAD
RINSE HOLD
SPIN RED.
NO SPIN
4.5 kg
113
(*) This programme is the reference programme for the Energy label according to EEC Directive 92/75.
The programme times are intended as a guide only. The actual time will vary depending on incoming water
temperature and pressure.
15
132994650.qxd
6/25/02
10:19 AM
Pagina
16
(Nero/Process Black pellicola)
Washing Programmes
Programmes for synthetics, mixed fabrics, delicates and wool
Wash programme/
Washing symbol
MIXED
FABRICS
DELICATES
WOOL
COLD WASH
Degree of soil
and type of laundry
Synthetic or mixed
fabrics, underwear,
coloured garments,
non-shrink shirts,
blouses.
Delicate fabrics, for
example curtains
Specially tested
programme for wool
garments bearing the
“Pure new wool, nonshrink, machine
washable” label.
Special programme for
hand washing fabrics
Special short
programme for lightly
soiled synthetic, mixed
fabrics and delicates
Programme
dial position
Description
5
Wash at 60 °C
6
Wash at 50 °C
7
Wash at 40 °C
Possible
options
PREWASH
RINSE HOLD
SPIN RED.
NO SPIN
85
2 kg
80
3 rinses
Short spin
8
Wash at 40 °C
9
Wash at 30 °C
60
PREWASH
RINSE HOLD
SPIN RED.
NO SPIN
2 kg
10
Wash at 30 °C
3 rinses
Short spin
RINSE HOLD
SPIN RED.
NO SPIN
1 kg
50
11
Cold wash
3 rinses
Short spin
RINSE HOLD
SPIN RED.
1 kg
43
2 kg
30
4.5 kg
30
3 rinses
Short spin
12
Separate rinse cycle for
hand washed items of
all fabric
13
3 rinses
Short spin
RINSE HOLD
SPIN RED.
NO SPIN
DRAIN
For emptying out the
last rinse water in
programmes with the
“rinse hold” option.
14
Draining of water
SPIN
Separate spin for
all fabric
15
Short spin
RESET / OFF
For cancelling the
wash programme
which is running and
for switching the
machine off
O
16
55
NO SPIN
RINSE HOLD
SPIN RED.
RINSES
Progr.
time
mins.
90
Wash at 30 °C
2 rinses
Short spin
QUICK
AND COOL
Max.
load
NO SPIN
-
SPIN RED.
4
4.5 kg
1,5
132994650.qxd
6/25/02
10:19 AM
Pagina
17
(Nero/Process Black pellicola)
Maintenance and Cleaning
Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
C0072
C0073
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
P0038
Cleaning the pump
The pump should be inspected regularly and particularly
if
• the machine does not empty and/or spin
• the machine makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump.
Proceed as follows:
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
External cleaning
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.
P1114
• Place a container close to the pump to collect any
spillage.
• Pull out the emergency emptying hose, place it in the
container and remove its cap.
17
132994650.qxd
6/25/02
10:19 AM
Pagina
18
(Nero/Process Black pellicola)
• When no more water comes out, unscrew the pump
cover and remove it. Always keep a cloth nearby to
dry up spillage of water when removing the cover.
Clean the filter using a hard bristle brush.
Tighten up the inlet hose.
P1090
P1115
The dangers of freezing
• Remove any objects from the pump impeller by
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
● Turn off the water tap.
● Unscrew the inlet hose.
● Place the end of the emergency emptying hose and
that of the inlet hose in a bowl placed on the floor
and let water drain out.
● Screw the water inlet hose back on and reposition
the emergency emptying hose after having put the
cap on again.
● When you intend to start the machine up again,
make sure that the room temperature is above 0°C.
rotating it.
• Put the cap back on the emergency emptying hose and
place the latter back in its seat.
Important!
Every time you drain the water through the emergency
emptying hose you must pour 2 litres of water into the
main wash compartment of the detergent drawer and
then run the drain programme. This will activate the
ECO valve avoiding that part of the detergent remains
unused at next washing.
P1117
• Screw the pump cover fully in.
• Close the pump door.
Emergency emptying out
If the water is not discharged, proceed as follows to
empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water
stops flowing out;
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its seat after
having plugged it;
• screw the pump cover again and close the door.
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the pump.
Never remove the pump cover during a wash cycle,
always wait until the appliance has finished the cycle,
and is empty. When replacing the cover, ensure it is
securely retightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filter
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water tap. Unscrew the water inlet hose.
18
132994650.qxd
6/25/02
10:19 AM
Pagina
19
(Nero/Process Black pellicola)
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
During machine operation it is possible that the “end” light flashes to indicate that the machine is not working. On the
AW 1400 W an acoustic warning signal is also heard.
• 4 flashes / 4 beeps = door open
• 2 flashes / 2 beeps = the water is not drained
• 1 flash / 1 beep = there is no water filling
Once the problem has been eliminated, press the “start pause” button to restart the programme. If after all checks, the
problem persists, contact your local Service Centre.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
The machine does not start
Possible causes
●
●
●
●
●
The machine does not fill
●
●
●
●
The machine fills then empties
immediately
●
●
●
The machine does not empty and/or
does not spin
●
●
●
●
●
●
There is water on the floor
●
●
●
●
●
●
Unsatisfactory washing results
●
●
●
●
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no supply at the socket
The main fuse or the fuse in the plug has blown.
The selector dial is not correctly positioned and the “start pause”
button has not been depressed.
Ensure the water tap is open.
The filter in the inlet hose is blocked.
The inlet hose may be squashed or kinked.
The door has not been closed.
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The drain hose may be squashed or kinked.
The “rinse hold” or “no spin” option has been selected.
The drain pump may be blocked.
The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.
The drainage system pipes are blocked.
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from one of the inlet hose fittings. It
is not always easy to see this as the water runs down the hose; check to
see if it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
The cap on the emergency emptying hose has not been replaced after
cleaning the filter.
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme has not been selected.
Too much laundry has been placed in the drum.
19
132994650.qxd
6/25/02
10:19 AM
Pagina
20
(Nero/Process Black pellicola)
Symptom
Possible causes
The machine vibrates when spinning
●
●
●
●
●
The door will not open
●
●
●
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not stable and level (check diagonally).
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
The programme is still running.
The door lock has not yet released (the “door” light is still on).
Water in the tub: the door cannot be opened if water is present in the
tub.
Spinning starts late or the machine
does not spin
●
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 10 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and reselect the spin programme.
The machine makes an unusual
noise
●
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.
No water is visible in the drum
●
Machines based on modern technology operate very economically
using very little water without affecting performance.
Service & Spare Parts
Mo
Pro d. .....
d.
No .....
. .....
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Tricity Bendix Service Force Centre by
telephoning:
.
Ser
. No
.....
. .....
....
0870 5 929929
Mod. ..........
Prod. No. ...........
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance (found
on the rating plate - see picture).
5. The purchase date
P0042 BD
Ser. No. .........
Customer Care
For general enquiries concerning your Tricity Bendix
appliance or for further information on Tricity Bendix
products, please contact our Customer Care Department
by letter or telephone as follows:
Customer Care Department
Tricity Bendix
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel 08705 950 950*
* calls to this number may be recorded for training
purposes.
20
132994650.qxd
6/25/02
10:19 AM
Pagina
21
(Nero/Process Black pellicola)
Guarantee Conditions
Standard guarantee conditions
Exclusions
We, Tricity Bendix undertake that if, within 12 months
of the date of the purchase, this Tricity Bendix appliance
or any part thereof is proved to be defective by reason
only of faulty workmanship or materials, we will, at our
option, repair or replace the same FREE OF ANY
CHARGE for labour, materials or carriage on condition
that:
● The appliance has been correctly installed and used
only on the electricity supply stated on the rating
plate.
● The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
● The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
All service work under this guarantee must be
undertaken by a Tricity Bendix Service Force Centre.
Any appliance or defective part replaced shall become
the Company’s property.
This guarantee is in addition to your statutory and other
legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
This guarantee does not cover:
●
●
●
●
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
Products of Tricity Bendix manufacture which are
NOT marketed by Tricity Bendix.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
● The guarantee starts from the date you first
purchased your product.
● The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products.
● The guarantee relates to you and cannot be
transferred to another user.
● Your new home is within the European Community
(EC) or European Free Trade Area.
● The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household.
● The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0)344 62 20 13
Germany
Nurnberg
+49 (0)800 234 7378
Italy
Pordenone
+39 (0)800 11 75 11
Sweden
Stockholm
+46 (0)20 78 77 50
UK
Slough
+44 (0)1753 219898
21
132994650.qxd
6/25/02
10:19 AM
Pagina
22
(Nero/Process Black pellicola)
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Should the appliance power supply cable need to
be replaced, this should be carried out by our
Service Force Centre.
Technical Specifications
DIMENSIONS
Height
Width
Depth
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
85 cm (33.5”)
60 cm (23.6”)
57 cm (22.4”)
230-240 V/50 Hz
2050 W (10A)
WATER PRESSURE
Minimum
Maximum
MAXIMUM RECOMMENDED LOAD
Cotton, linen
Synthetics
Delicate fabrics
Wool
SPIN SPEED
Maximum
CONSUMPTION DATA FOR WASHING
4.5 KG NORMALLY SOILED COTTON
ITEMS AT 60°C (PROGR. ECO WASH)
Energy
Water
50 kPa
800 kPa
4.5 kg
2 kg
2 kg
1 kg
1200 rpm (AW 1200 W)
1400 rpm (AW 1400 W)
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
22
0.85 kWh
49 litres
132994650.qxd
6/25/02
10:19 AM
Pagina
23
(Nero/Process Black pellicola)
Unpacking
Fill all the holes with the plastic plugs supplied with the
instruction booklet.
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
Using a spanner unscrew and remove the two rear
bottom screws. Slide out the two plastic pins.
Lay the machine gently on its back, making sure that the
hoses are not squashed.
P1128
P0002
Important !
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
In case of moving out the same precautions as per
paragraph “The dangers of freezing” must be taken i.e.
the residual water in the hoses must be pumped out.
Positioning
P0001
P1129
Remove the polystyrene block from the bottom of the
machine and release the two plastic bags.
Very carefully slide out the left polythene bag, removing
it towards the right and then downwards.
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to suitable existing tap with the drain
hose discharging into a sink.
The appliance has one inlet hose, with female 3/4” BSP
thread connector. If this connection is not compatible
with the plumbing of the existing installation, a variety
of connectors are available from good hardware stores
and plumbers merchants to suit most domestic
plumbing. Any alteration to your existing plumbing
must be carried out by a competent person, or qualified
plumber.
1
2
3
P1124
P1126
Repeat the operation for the right polythene bag,
removing it towards the left and then upwards.
Installation on a Suspended Floor
P1127
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
Remove the polystyrene base.
Set the machine upright and unscrew the remaining rear
screw. Slide out the relevant pin
23
132994650.qxd
6/25/02
10:19 AM
Pagina
24
(Nero/Process Black pellicola)
Water drainage
Connect the hose to a tap with a 3/4” thread.
Do not use previously used hoses for water connection.
This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.
The appliance drain hose should hook into a standpipe,
the hook in the drain hose is formed using the plastic
“U-Piece” supplied.
30 cm (12")
Water inlet
P1088
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be connected to a cold water
supply.
A minimum water pressure of 50 kPa (0.5 bar) is
required for safe operation of the appliance.
P1074
The standpipe should have an internal diameter of
approximately 38mm (see diagram) thus ensuring there
is an air break between the drain hose and standpipe.
Min. 30 cm.(12")
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
Set the hose correctly by loosening the ring nut. After
positioning the inlet hose, be sure to tighten the ring nut
again to prevent leaks.
38 mm.(1/1 2") diameter
standpipe
P1040
When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level.
The upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
Max. 90 cm.
(35.4")
Min.60 cm.
(23.6")
3 pin
P0021
P1130
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
24
132994650.qxd
6/25/02
10:19 AM
Pagina
25
(Nero/Process Black pellicola)
Special conditions
If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-Piece” supplied.
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
Warning
The machine should NOT be placed on deep pile
carpeting.
P0022
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
The drain hose must not be kinked.
Important
●
●
Before connecting up the machine to new pipework
or to pipework that has not been used for some time,
run off a reasonable amount of water to flush out any
debris that may have collected in the pipes.
For a correct functioning of the machine the drain
hose must be hooked on the proper support piece
situated on the top of the back side of the appliance.
In the interest of the
environment
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
If you require any further advice please contact your
local water authority.
Levelling
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable.
P1051
SHOWER
SINK
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Some vibration is inevitable, especially if mounted on a
wooden floor.
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
TOILET
BATH
WASHING
MACHINE
BIDET
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
RIVER
P0987
25
RIVER
132994650.qxd
6/25/02
10:19 AM
Pagina
26
(Nero/Process Black pellicola)
Electrical connection
The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
WARNING:
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.
Should the appliance power supply cable neeed to be
replaced, this should be carried out by our Service
Force Centre.
Mo
Pro d. .....
d.
No .....
. .....
Note
When the appliance is installed the power supply cable
must be accessible.
.
Ser
. No
.....
. .....
....
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042 BD
Permanent connection
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363) fuse must
be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
GREEN & YELLOW
13 A
E
N
L
BROWN
BLUE
P1041
CORD CLAMP
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol
or coloured green and yellow.
26
132994650.qxd
6/25/02
10:19 AM
Pagina
27
(Nero/Process Black pellicola)
Tricity Bendix, 55-77High Street, Slough, Berkshire SL1 1DZ
Consumer care telephone number 08705 950950
© Electrolux PLC 2002