ZANUSSI FL1089ALU User Manual

Add to my manuals
26 Pages

advertisement

ZANUSSI FL1089ALU User Manual | Manualzz
132993430.qxd
10/31/02
9:08 AM
Pagina
1
(Nero/Process Black pellicola)
LAVADORA
WASHING MACHINE
FL 1089
FL 1089ALU
FL 1289
INICIO
DIFERIDO
T
EM
132993430
WET ANTIARRUGAS
P E R AT U
EN
FL 889
PRELAVADO
1000
900
700
500
90°C
60°C
40°C
30°C
FRIO
C
TE J ID O S
O
ALGODON
SINTETICOS
DELICADOS
LANA
LAVADO
A MANO
TRI FU G A
D
ON/OFF
RA
800 RPM
REMOJO
ACLARADO
ADICIONAL
FUNCION
EXPRESS
ECONOMY
40° AA
EXCLUIR
FASE
CICLO
NOCHE
I N I C I O /PA U S A
A NU L A
R
MANUAL DE USO
USER MANUAL
E
GB
132993430.qxd
10/31/02
9:09 AM
Pagina
26
(Nero/Process Black pellicola)
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use recycled paper.
26
132993430.qxd
10/31/02
9:09 AM
Pagina
27
(Nero/Process Black pellicola)
Contents
28-29
Disposal
29
Tips for environmental protection
29
Technical specifications
30
Installation
31
Unpacking
31
Positioning
31
Water inlet
31
Water drainage
32
Electrical connection
32
Your new washing machine
33
Description of the appliance
33
Door locked pilot light
33
Detergent dispenser drawer
33
Use
Control panel
Controls
34
34-38
39
Sorting the laundry
39
Temperatures
39
Before loading the laundry
39
Maximum loads
39
Laundry weights
39
Removing stains
39
Detergents and additives
40
Operating sequence
Washing programmes
41
42-44
45
27
46
Bodywork
46
Door seal
46
Detergent dispenser drawer
46
Drain filter
46
Water inlet filter
47
Emergency emptying out
47
The dangers of freezing
47
Something not working?
34
Washing hints
International wash code symbols
Maintenance
48-49
ENGLISH
Warnings
132993430.qxd
10/31/02
9:09 AM
Pagina
28
(Nero/Process Black pellicola)
Warnings
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
Installation
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Always unplug the appliance and shut the water
tap after use.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
• Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
General safety
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the feet
and the floor.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing garments
in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
28
132993430.qxd
10/31/02
9:09 AM
Pagina
29
(Nero/Process Black pellicola)
Child safety
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
ENGLISH
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
• Keep all detergents in a safe place out of children’s
reach.
• Make sure that children or pets do not climb into
the drum. To avoid this the machine incorporates a
special feature. To activate this device, rotate the
button (without pressing it) inside the door
clockwise until the groove is horizontal. If
necessary use a coin.
P1131
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
Disposal
Packaging materials
The materials marked with the symbol
recyclable.
Machine
are
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Tips for environmental protection
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature, so saving energy.
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
• The machine works more economically if it is fully
loaded, but do not overload it (see maximum load
on page 30).
29
132993430.qxd
10/31/02
9:09 AM
Pagina
30
(Nero/Process Black pellicola)
Technical specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
57 cm
WASH LOAD
Cotton
Synthetics
Delicates
Woollens, hand wash
6 kg
3 kg
3 kg
2 kg
SPIN SPEED
1000 rpm max. (FL 1089, FL 1089ALU
1200 rpm max. (FL 1289)
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MINIMUM FUSE PROTECTION
220-230 V/50 Hz
2200 W
10 A
WATER PRESSURE
50 kPa
800 kPa
Minimum
Maximum
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
30
132993430.qxd
10/31/02
9:09 AM
Pagina
31
(Nero/Process Black pellicola)
Installation
Unpacking
6. Plug all the holes with the plugs which you will
find in the envelope containing the instruction
booklet.
All transit bolts and packing must be removed
before using the appliance.
ENGLISH
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the two
rear bottom screws. Slide out the two plastic pins.
Lay the machine on its back, taking care not to
squash the hoses. This can be avoided by
placing one of the corner packing pieces between
the machine and the floor.
P1128
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
P0001
P1129
P0002
2. Remove the polystyrene block from the bottom of
the machine and release the two plastic bags.
1
2
3
P1051
P1124
Water inlet
3. Very carefully slide out the left polythene bag,
removing it towards the right and then
downwards.
Connect the water inlet hose to a tap with a 3/4"
thread.
Do not use already employed hoses.
4. Very carefully slide out the right polythene bag,
removing it towards the left and then upwards.
The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks.
P1126
P1127
5. Set the machine upright and remove the
remaining rear screw. Slide out the relevant pin.
P1088
P0021
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
31
132993430.qxd
10/31/02
9:09 AM
Pagina
32
(Nero/Process Black pellicola)
Water drainage
Electrical connection
The end of the drain hose can be positioned in three
ways:
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this should be carried
out by our Service Centre.
Please ensure that when the appliance is
installed the power supply cable is easily
accessible.
P0022
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
The drain hose must not be kinked. Run it along the
floor; only the part near the drainage point must be
raised.
P0023
32
132993430.qxd
10/31/02
9:09 AM
Pagina
33
(Nero/Process Black pellicola)
Your new washing machine
This new washing machine, which is fitted with the Jet system, patented Zanussi, meets all modern needs for
effective treatment of laundry with low water, energy and detergent consumption.
• The possibility of selecting the temperature, spin speed and all the options offered by this washing machine
gives you truly “customised” washing.
• The DELAY START option allows you to delay starting of the wash programme to any time of day, so
allowing you for instance to make use of overnight economy electricity tariffs.
• The programme progress display shows the programme steps selected and the programme phase which
is running.
• The special wool programme with its new delicate wash system treats your woollens with extreme care.
• The balance control device ensures the machine is stable during the spin.
Description of the appliance
1 Detergent dispenser drawer
1
2
2 Control panel
3 Door locked pilot light
INICIO
DIFERIDO
ALGODON
SINTETICOS
DELICADOS
LANA
LAVADO
A MANO
EM
T
TE J ID O S
WET ANTIARRUGAS
P E R AT U
EN
C
5 Adjustable feet
FL 889
PRELAVADO
1000
900
700
500
90°C
60°C
40°C
30°C
FRIO
O
ON/OFF
TRI FU G A
D
800 RPM
RA
4 Drain filter
REMOJO
ACLARADO
ADICIONAL
FUNCION
EXPRESS
ECONOMY
40° AA
EXCLUIR
FASE
CICLO
NOCHE
I N I C I O /PA U S A
A NU L A
R
3
Door locked pilot light
It stays on during the whole programme indicating
that the door is locked.
When the light goes out, the door can be opened
(see page 44).
4
5
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
C0063
33
ENGLISH
Further savings are achieved by washing small loads of laundry, since water and electricity consumption is
proportional to the quantity and type of laundry being washed.
132993430.qxd
10/31/02
9:09 AM
Pagina
34
(Nero/Process Black pellicola)
Use
Control panel
INICIO
DIFERIDO
1
2
3
P E R AT U
4
ACLARADO
ADICIONAL
FUNCION
EXPRESS
ECONOMY
40° AA
I N I C I O / PA U S A
T R IF U G A
5
EXCLUIR
FASE
CICLO
NOCHE
O
EN
C
EM
T
T E JI D O S
WET ANTIARRUGAS
REMOJO
D
ON/OFF
PRELAVADO
1000
900
700
500
90°C
60°C
40°C
30°C
FRIO
RA
ALGODON
SINTETICOS
DELICADOS
LANA
LAVADO
A MANO
FL 1089
6
7
8
9
10
A NULA
11
R
12 13
fabrics to be hand-washed (HAND WASH programme).
1 ON/OFF button
By selecting position FRIO the machine will wash with
cold water. To be used for extremely delicate items,
such as curtains.
Press this button to switch the washing machine on.
The display (9) will show three blinking dashes or a
blinking zero. You will find more detailed
explanations on page 35-36 (see “DISPLAY”).
Press the ON/OFF button again to switch the
machine off.
Important!
By depressing TEMPERATURE and SPIN SPEED
(CENTRIFUGADO) buttons simultaneously, the
acoustic signal is suppressed when selecting the
programmes, in case of incorrect option selection
and at the end of the cycle.
2 MAINS-ON light
This light is connected to the ON/OFF button. It lights
up when you press the button, and goes out when
you press it again.
5 SPIN SPEED button (CENTRIFUGADO)
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
speed different from the one proposed by the
washing machine. The relevant light will light up.
3 FABRIC button (TEJIDOS)
Press this button repeatedly to select the programme
on the basis of the type of laundry to be washed. The
light relevant to the selected programme will light up.
The washing machine will propose a temperature and
automatically select the maximum spin value provided
for the programme you have chosen. You can change
these values by operating buttons 4 and 5.
Maximum speeds are:
• for cotton: 1200 rpm or 1000 rpm depending on the
model.
• for synthetic fabrics, wool, and fabrics to be handwashed: 900 rpm;
• for delicate fabrics: 700 rpm.
WET ANTI-ARRUGAS (NO SPIN) option
By selecting this option the spinning phases are
suppressed.
This function is not available for cotton and linen.
To be selected for extremely delicate items.
Hand wash
(Lavado a mano)
When you select this programme, you obtain a
particularly delicate washing, suitable for articles of
clothing whose label indicates that they must be
hand-washed
.
6 / 7 OPTION buttons
4 TEMPERATURE button (TEMPERATURA)
Press these buttons to select the following options:
Press this button repeatedly to increase or decrease
the temperature, if you want your laundry to be washed
at a temperature different from the one proposed by the
washing machine. The relevant light will light up.
Maximum temperatures are 90°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
• PREWASH (PRELAVADO): select this option if
you wish your laundry to be prewashed before the
main wash (not available for wool and handwash cycle).
The prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics,
34
10/31/02
9:09 AM
Pagina
35
(Nero/Process Black pellicola)
As all spinning phases are suppressed, this washing
cycle is very quiet and it can be useful at night or in
times with a more economical power rate.
whereas in the programme for delicate fabrics the
water is only drained.
• SOAK (REMOJO): select this option if you wish to
perform a soak of about 30 minutes at 30°C to
your laundry. By pressing the DELAY START
(INICIO DIFERIDO) button the soak time can be
prolonged up to 24 hours max. After this time the
wash cycle will automatically start.
This function is not available for wool and handwash cycle.
The soak ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics,
whereas in the programme for delicate fabrics the
water is only drained.
On cotton and synthetic programmes the rinses will
be performed with more water.
At the end of the cycle, the light corresponding to
NIGHT WASH option is on and the START/PAUSE
button light will flash, to indicate that the water must
be drained. A static zero appears on the display.
To complete the cycle, choose one of the following
options:
• Draining and spin:
- Press the START/PAUSE button. The machine
will drain the water, then spin the laundry at the
maximum speed provided for the selected
programme.
- Select spin speed by means of button 5, and
press the START/PAUSE button.
• Drain only
- Press the RESET (ANULAR) button once, so as
to cause the DRAIN
light to light up, then
press the START/PAUSE button.
• The same button allows you to select the QUICK
function (FUNCION EXPRESS), for laundry that is
only slightly soiled (not for wool and HAND
WASH programme).
The washing time will be reduced according to the
type of fabric and the selected temperature.
The PREWASH, SOAK and QUICK options
cannot be selected together.
Important! If you accidentally press the RESET
(ANULAR) button more than once, the display will
show three blinking dashes. To cause the
washing machine to drain the water, select any
washing programme by means of the FABRIC
(TEJIDOS) button, then press RESET (ANULAR)
three times in order to select the DRAIN position
(only the DRAIN
light will remain lit).
• SUPER RINSE (ACLARADO ADICIONAL): this
option can be selected with all programmes except
the wool and hand wash programme. The
machine performs 4 rinses instead of 3. This option
is recommended for people who are allergic to
detergents, and in areas where the water is very
soft.
• ECONOMY 40°AA: this option can be selected for
cottons and synthetics lightly or normally soiled
with a temperature of 40°C or higher.
If you select 40°C , the machine will prolong the
time at 40°C in the washing phase, this will allow
an A class in energy efficiency and washing
performance to be achieved.
If you select 90°C and press the ECONOMY
40°AA button, the washing temperature will be
reduced from 90°C to 60°C.
If you select 60°C and press the ECONOMY
40°AA button, the washing temperature will be
reduced to 40°C. In both cases the washing time
will be prolonged.
9 Display
The following pieces of information are shown on the
display:
• Three blinking dashes, when a programme is
cancelled by means of the RESET (ANULAR)
button.
The three blinking dashes will also appear when you
press the ON/OFF button to switch the machine on,
if the previously selected cycle has been erased.
The SUPER RINSE and the ECONOMY 40°AA
options can be selected together by means of the
relevant button.
---
8 NIGHT WASH button (CICLO NOCHE)
When you choose this option, the machine will not
drain the water of the last rinse, so as not to wrinkle
the laundry.
35
ENGLISH
132993430.qxd
132993430.qxd
10/31/02
9:09 AM
Pagina
36
(Nero/Process Black pellicola)
• Duration of washing programme in hours
and minutes, after you have selected a
programme.
The delay time is displayed for 3 seconds, then the
duration of the selected programme reappears.
After you have pressed the START/PAUSE button,
the countdown begins, and the delay time value
decreases by one unit every hour.
You can delay the start of the selected programme
by up to 24 hours in one hour intervals.
2.05
• An incorrect option selection has been made:
this is indicated by the message Err when a
function incompatible with the current programme
is selected.
While the programme is running (after you have
pressed the START/PAUSE button), the displayed
time value decreases by one unit every minute.
• The washing machine has stopped with water in
the tub, at the end of a programme with the
NIGHT WASH (CICLO NOCHE) option: this is
indicated by a static zero.
• The washing machine has completed the
programme: this is indicated by a blinking zero.
At the same time, the door locked light goes out.
The zero will reappear when you switch the
washing machine on, unless the previous
programme has been erased by means of the
RESET (ANULAR) button.
The incorrect selection is also indicated by an
audible warning signal.
• An alarm code indicates a fault in the machine
operation (see the relevant chapter on page 48).
E20
0
10 START/PAUSE button
Important!
The first time you use the washing machine,
when you switch it on, it may display a blinking zero and
give an audible warning signal. This is due to the fact
that the washing machine has performed a washing
cycle during the manufacturer’s inspection tests, and
this cycle has not been erased after its completion.
(INICIO/PAUSA)
This button has three functions:
• Start: after you have selected the desired
programme and options, press this button to start
the washing machine. The light above the button
will stop flashing and remain lit.
If you have selected a delay time by means of
button 12, the countdown will begin and will be
shown on the display.
• Delay start (Inicio diferido), a time value
indicated in hours and selected by means of the
relevant button.
• Pause: when you press this button again, the
programme in progress is interrupted. The light
above the button will start flashing. To restart the
programme, press the button again.
When you PAUSE the cycle, the DOOR LOCKED
light goes out, and it becomes possible to open the
door, provided
• the washing machine is not in the heating phase;
• the level of the water is not high;
• the drum is not turning.
36
10/31/02
9:09 AM
Pagina
37
(Nero/Process Black pellicola)
Important! You must set the washing machine to
PAUSE before you make any change in the
programme in progress.
• SPIN
• Draining of water and spinning after the
execution of programmes with the NIGHT WASH
(CICLO NOCHE) option.
• DRAIN
Depress RESET (ANULAR) twice, the pilot lights
WASH
and RINSES
go out.
Depress RESET (ANULAR) three times, the
pilot lights WASH
, RINSES
and SPIN
go out.
11 RESET (ANULAR) button
Example:
At the end of a programme, you must press this
button once or repeatedly, in order to clear the
contents of the memory (the display will show three
blinking dashes); otherwise, the next time you switch
the washing machine on, the blinking zero will
reappear and the audible warning signals relevant to
the end of the previous cycle will be given.
PREWASH
PRELAVADO
WASH
LAVADO
RINSES
ACLARADOS
SPIN
CENTRIFUGADO
DRAIN
DESCARGA
You can also press the RESET (ANULAR) button to
exclude one or several phases of the programme
which is running, as indicated below:
In this case the
machine will perform
the rinses and spin.
• If the machine is switched off:
- set the washing machine to PAUSE by pressing the
START/PAUSE button (the relevant light will flash);
- depress ON/OFF button to switch it on;
- select the type of fabric by means of button
TEJIDOS:
- press the RESET (ANULAR) button once or several
times, until the required phase(s) is(are) cancelled
(the light next to the phase(s) will go out).
- select the special programme as previously
described.
Example:
PREWASH
PRELAVADO
WASH
LAVADO
RINSES
ACLARADOS
SPIN
CENTRIFUGADO
DRAIN
DESCARGA
In this case, the spin
(at the speed provided
for the selected type of
fabric) will be
performed.
12 DELAY (INICIO DIFERIDO) button
This button makes it possible to delay the starting of
the programme by up to 24 hours. The delay you
have selected is shown on the display for about 3
seconds; afterwards, the duration of the programme
reappears.
You must select this option after you have set the
programme and before you press the
START/PAUSE button.
This button allows you also to select special
programmes, such as RINSES, SPIN and DRAIN.
The time value shown on the display will decrease
by one unit every hour.
• If the machine is already switched on because it
has just performed a washing programme, proceed
as follows:
You can change the delay time at any moment,
before you press the START/PAUSE button.
If you have already pressed the START/PAUSE
button, and you wish to change or cancel the delay
time, proceed as follows:
- depress RESET (ANULAR) once or repeatedly to
cancel the previously performed programme (three
blinking dashes will appear on the display);
- select the type of fabric by means of button
TEJIDOS;
• set the washing machine to PAUSE by pressing the
START/PAUSE button;
- select the special programme:
• press the DELAY button until the display shows the
desired delay time or
• RINSES
• press the DELAY button once, to erase the delay
time. The display will indicate “0h”.
Depress RESET (ANULAR) once, the pilot light
WASH
goes out.
• press the START/PAUSE button again.
37
ENGLISH
132993430.qxd
132993430.qxd
10/31/02
9:09 AM
Pagina
38
(Nero/Process Black pellicola)
Important!
The door will be locked throughout the delay time
(DOOR LOCKED light lit).
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the
START/PAUSE button. After you have closed the
door, press the START/PAUSE button again.
13 Programme phase indicator lights
When you select a programme, the lights relevant to
the phases that form the programme light up.
PREWASH
WASH
RINSES
SPIN
DRAIN
After you have started the programme, only the light
relevant to the phase that is currently being carried
out will remain lit.
38
10/31/02
9:09 AM
Pagina
39
(Nero/Process Black pellicola)
Delicate fabrics, woollens and hand wash
programme: drum no more than one third full.
Washing hints
Washing a maximum load makes the most efficient
use of water and energy.
Sorting the laundry
For heavily soiled laundry, reduce the load size.
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
Laundry weights
The following weights are indicative:
Temperatures
bathrobe
90°
for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
napkin
100 g
quilt cover
700 g
sheet
500 g
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
pillow case
200 g
tablecloth
250 g
towelling towel
200 g
tea cloth
100 g
night dress
200 g
ladies’ briefs
100 g
60°
Frio (cold) for delicate items (e.g. net curtains),
30°-40° mixed laundry including synthetic fibres
and woollens.
The wool wash cycle of this machine has
been approved by Woolmark for the
washing of machine washable Woolmark
products provided that the garments are
washed according to the instructions on
the garment label and those issued by
the manufacturer of this washing
machine. M9605.
1200 g
man’s work shirt
600 g
man’s shirt
200 g
man’s pyjamas
500 g
blouse
100 g
men’s underpants
100 g
Removing stains
Before loading the laundry
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Maximum loads
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Recommended loads are indicated in the
programme charts.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
General rules:
Cotton, linen: drum full but not too tightly packed;
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Synthetics: drum no more than half full;
Ball point pen and glue: moisten with acetone (*),
39
ENGLISH
132993430.qxd
132993430.qxd
10/31/02
9:09 AM
Pagina
40
(Nero/Process Black pellicola)
lay the garment on a soft cloth and dab the stain.
Quantity of detergent to be used
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
Follow the product manufacturers’ instructions on
quantities to use.
Use less detergent if:
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
– you are washing a small load,
– the laundry is lightly soiled,
(*) do not use acetone on artificial silk.
– large amounts of foam form during washing.
Detergents and additives
Degrees of water hardness
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
Degrees
Level
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
Characteristic
1
soft
All commonly available washing machine detergents
may be used in this appliance:
2
medium
– powder detergents for all types of fabric,
3
hard
– powder detergents for delicate fabrics (60°C max)
and woollens,
4
very hard
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents, a
programme without prewash or soak must be
selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked
before
starting the wash programme.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
40
German
°dH
French
°T.H.
0- 7
0-15
8-14
16-25
15-21
26-37
more than more than
21
37
132993430.qxd
10/31/02
9:09 AM
Pagina
41
(Nero/Process Black pellicola)
International wash code symbols
Energetic wash
95
60
40
30
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Delicate wash
60
Bleaching
Bleach in cold water
40
ENGLISH
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Hand wash
30
40
Do not
wash
at all
Do not bleach
Ironing
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
41
Tumble dry
Do not
tumble dry
132993430.qxd
10/31/02
9:09 AM
Pagina
42
(Nero/Process Black pellicola)
4. Switch the machine on
Operating sequence
To switch the machine on, press the ON/OFF button
: the mains-on light comes on.
Before the first wash we recommend that you run a
cotton cycle at 60°C, with the machine empty, in
order to remove any manufacturing residue from the
drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
The display will show three blinking dashes or a
blinking zero.
O N / O FF
1. Place the laundry in the drum
0
---
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
5. Select the desired programme / fabric
Press the FABRIC (TEJIDOS) button repeatedly, in
order to select the desired programme/fabric. The
relevant light will light up.
The lights relevant to the phases that form the
programme will light up.
The display will show the duration of the selected
programme, calculated on the basis of the maximum
load for each type of fabric. The START/PAUSE
(INICIO/PAUSA) button light will start flashing.
P0004
2. Measure out the detergent
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the execution
of the cycle.
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment
.
If you wish to carry out a soak or a prewash
programme, pour detergent into the appropriate
compartment marked
.
ALGODON
SINTETICOS
DELICADOS
LANA
LAVADO
A MANO
3. Measure out the additive
If required, pour fabric softener into the compartment
marked
, without exceeding the «MAX» mark.
Close the drawer gently. This is particularly important
if you are using a fabric conditioner because if the
drawer is slammed it will cause the conditioner to
enter the machine prematurely.
C0064
PREWASH
WASH
RINSES
SPIN
DRAIN
6. Select the temperature
Press the TEMPERATURE button if you wish to
select a temperature value different from the one
proposed by the washing machine.
The relevant light will light up.
C0065
42
10/31/02
9:09 AM
Pagina
43
(Nero/Process Black pellicola)
9. Select the SUPER RINSE and/or
ECONOMY 40° AA option
90°C
60°C
40°C
30°C
FRIO
If your laundry is lightly or normally soiled and it is
necessary to prolong the washing time, select the
ECONOMY 40° AA option.
Press this button so as to cause one of both lights to
light up.
P E R AT U R
A
T
EM
If you wish the laundry to undergo an extra rinse,
select the SUPER RINSE option.
7. Select the spin speed or WET ANTIARRUGAS (NO-SPIN) option
ACLARADO
ADICIONAL
Press the SPIN SPEED (CENTRIFUGADO) button
repeatedly, in order to select the desired spin speed
or the WET ANTI-ARRUGAS option. The relevant
light will light up.
ECONOMY
40° AA
FL 1089 - FL1089ALU
10. Select the NIGHT WASH (CICLO
NOCHE) option
1000
900
700
500
If you select the NIGHT WASH option, the machine
will stop at the end of the programme with the water
still in the tub. The relevant light will light up.
WET ANTIARRUGAS
T RI F U G AD
O
C
EN
8. Select the desired options
CICLO
NOCHE
If your laundry is very dirty, it may be advisable to
select the PREWASH (PRELAVADO) option.
If you wish the laundry to undergo a soak, select the
SOAK (REMOJO) option.
If your laundry is only slightly soiled, select the
QUICK (FUNCION EXPRESS) option.
11. Select the DELAY TIME (INICIO
DIFERIDO)
Before you start the programme, if you wish the
starting to be delayed, press the DELAY (INICIO
DIFERIDO) button repeatedly, or keep it pressed, to
select the desired delay. The selected delay time
value (up to 24 hours) will appear on the display for 3
seconds, then the duration of the programme will
appear again.
PRELAVADO
REMOJO
FUNCION
EXPRESS
INICIO
DIFERIDO
43
ENGLISH
132993430.qxd
132993430.qxd
10/31/02
9:09 AM
Pagina
44
(Nero/Process Black pellicola)
• the drum is not turning.
12. Start the programme
If these requirements are met, when you pause the
washing machine, the DOOR LOCKED light goes
out and the door can be opened.
Press the START/PAUSE button. The relevant light
will stop flashing, the DOOR LOCKED light will light
up, and only the light relevant to the phase that is in
progress will remain lit.
If you have chosen a delayed start, the washing
machine will begin the countdown.
The display will show the duration of the programme
or the selected delay.
Should it not be possible to open the door, and
should it be absolutely necessary to do so, switch
the machine off by pressing the ON/OFF button.
After approximately 3 minutes, you can open the
door.
Pay attention to the level and temperature of the
water in the washing machine!
13. How to change a programme
during its cycle
When you close the door and press the ON/OFF
button again, the washing machine will resume the
programme from the point where it had been
interrupted.
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button.
It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is
possible, obviously, only during the washing phase.
When you make a change in these two parameters,
the washing machine will resume the cycle from the
beginning.
16. End of programme
At the end of the programme, the washing machine
stops automatically, gives an audible signal, and
displays a blinking zero.
If you had selected the NIGHT WASH (CICLO
NOCHE) option, the START/PAUSE button light
flashes to indicate that the water must be drained.
The display shows a steadily lit zero.
When the programme has been completed, a
blinking zero appears on the display and the audible
signal is given.
If it is necessary to drain the water in order to change
the programme in progress, proceed as follows:
• PAUSE the machine by pressing the
START/PAUSE button;
• press the RESET (ANULAR) button repeatedly,
until only the DRAIN
light remains lit;
The DOOR LOCKED light goes out at once.
Press the RESET (ANULAR) button repeatedly to
erase the programme that has just been carried
out. If you omit to do this, the next time you
switch the washing machine on, the blinking zero
will appear on the display and you will hear the
audible signal.
• press the START/PAUSE button again.
When the water has been drained, the display shows
a blinking zero. You may now select a new
programme and press the START/PAUSE button to
start it.
Note: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRIC (TEJIDOS) button
and select a new programme.
14. How to cancel a programme
during its cycle
To cancel a programme that is being carried out, first
pause the washing machine by pressing the
START/PAUSE button, then press the RESET
(ANULAR) button repeatedly, until the display shows
three blinking dashes.
Press the ON/OFF button to switch the machine off.
The relevant light will go out.
Remove the laundry from the washing machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get
damaged in a subsequent wash (e.g. by shrinking) or
bleed colour into another load of laundry.
15. How to open the door during
a programme
You can open the door, after having set the washing
machine to PAUSE, provided the following
conditions exist:
We advise you to close the water supply tap and
disconnect the plug from the socket.
• the washing machine is not in the heating phase
beyond 55°C;
Leave the door ajar in order to air the washing
machine.
• the level of the water is not high;
44
132993430.qxd
10/31/02
9:09 AM
Pagina
45
(Nero/Process Black pellicola)
Programme chart
Washing programmes
60
95
Load
40
30
60
40
30
40
30
Delicate fabrics: e.g.
acrylic fabrics,
viscose, polyester,
synthetic
blends
40
30
Wool
2 kg
WOOLMARK
2 kg
Water
litres
Time
h/min.
55
2.39
Cottons
Algodón
60°-40°-30°C
FRIO (COLD)
Wash at
60°-40°-30°C
or cold
3 rinses
Long spin
CENTRIFUGADO
PRELAVADO
REMOJO
FUNCION EXPRESS
ACLARADO ADICIONAL
ECONOMY 40° AA
CICLO NOCHE
1.14
52
2.16
Synthetics
Sintéticos
60°-40°-30°C
FRIO (COLD)
Wash at
60°-40°-30°C
or cold
3 rinses
Short spin
CENTRIF./WET ANTI-ARR.
1.05
55
1.36
Delicates
Delicados
40°-30°C
FRIO (COLD)
Wash at
40°-30°C
or cold
3 rinses
Short spin
0.55
60
1.07
Wool
Lana
40°-30°C
FRIO (COLD)
Wash at
40°-30°C
or cold
3 rinses
Short spin
CENTRIF./WET ANTI-ARR.
0.4
63
55
Hand wash
Lavado a mano
40°-30°C
FRIO (COLD)
Wash at
40°-30°C
or cold
3 rinses
Short spin
CENTRIF./WET ANTI-ARR.
0.40
63
58
3 kg
3 kg
Energy
kWh
2.05
6 kg
Synthetic
fabrics and
blends: e.g.
shirts,
blouses,
underwear
Consumption*
CENTRIFUGADO
PRELAVADO
REMOJO
FUNCION EXPRESS
ACLARADO ADICIONAL
ECONOMY 40° AA
CICLO NOCHE
Cottons
Algodón
60°-90°C
** Coloured
cotton: e.g.
shirts,
blouses,
underwear,
towels, household linen
Description of
Available options
programme
Wash at
60°-90°C
3 rinses
Long spin
6 kg
White cotton:
e.g. sheets,
tablecloths,
household
linen
60
Programme/
temperature
PRELAVADO
REMOJO
FUNCION EXPRESS
ACLARADO ADICIONAL
ECONOMY 40° AA
CICLO NOCHE
CENTRIF./WET ANTI-ARR.
PRELAVADO
REMOJO
FUNCION EXPRESS
ACLARADO ADICIONAL
CICLO NOCHE
CICLO NOCHE
CICLO NOCHE
**The “coloured cotton programme” at 60°C is the reference programme for the data entered in the energy
label, in compliance with EEC 92/75 standards.
* This data is given purely as an indication: the consumption values may vary in relation to the quantity and
type of laundry, the temperature of the water supply and the ambient temperature. The data refers to the
highest temperature provided for each programme.
45
ENGLISH
Type of
laundry and
symbols on
labels
132993430.qxd
10/31/02
9:09 AM
Pagina
46
(Nero/Process Black pellicola)
Maintenance
Bodywork
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
Clean the outside of the machine with soap and
water only. Rinse with clean water and dry with a soft
cloth.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
P0038
Drain filter
The drain filter collects threads and small objects
inadvertently left in the laundry. Check regularly that
the filter is clean.
Open the filter door.
Place a container under the filter and unscrew it.
P1050
Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
Pull out the filter.
To facilitate cleaning, the top part of the additive
compartments can be removed.
Clean the filter under a running tap, then refit it,
screwing it fully in.
C0066
P0861
C0067
P0859
46
P0860
P0040
10/31/02
9:09 AM
Pagina
47
(Nero/Process Black pellicola)
Water inlet filter
Frost precautions
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet hose is not
blocked.
IIf the machine is exposed to temperatures below
0°C, certain precautions should be taken.
●
Turn off the water tap.
Turn off the water tap.
●
Unscrew the inlet hose.
Unscrew the hose from the tap.
●
Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hose in a bowl. Run the draining programme.
Clean the filter with a stiff brush.
Screw the hose back onto the tap.
To do this:
●
Switch the machine on
●
Select a washing programme
Press the RESET (ANULAR) button three
times
●
●
P1090
Emergency emptying out
If the water is not discharged (outlet pump is
blocked, filter or drain hose are clogged), proceed as
follows to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• place a bowl on the floor;
• put the drain hose end into the bowl and let the
water come out.
Should it not be possible to have access to the outlet
hose because, for example, the appliance is built in
the kitchen furniture, slightly loosen the outlet filter
after placing a bowl on the floor, to let the water
come out slowly.
At the end screw the filter again.
47
Press INICIO/PAUSE button
●
Disconnect the appliance.
●
Screw the inlet hose and reposition the drain
hose.
●
When you intend to start the machine up again,
make sure that the room temperature is above
0°C.
ENGLISH
132993430.qxd
132993430.qxd
10/31/02
9:09 AM
Pagina
48
(Nero/Process Black pellicola)
Something not working?
Problems which you can resolve yourself.
During machine operation it is possible that one of the following alarm codes appears on the display:
- E10: problem with the water supply
- E20: problem with water draining
- E40: door open
Once the problem has been eliminated, press the START/PAUSE button
all checks, the problem persists, contact your local Service Centre.
Problem
to restart the programme. If after
Possible cause
• The machine does not start up:
• The door is not firmly closed. (E40)
• The machine is not plugged in or there is no power
at the socket.
• The main fuse has blown.
• The START/PAUSE (INICIO / PAUSA) button has
not been depressed.
• The DELAY START (INICIO DIFERIDO) option
has been selected.
• The machine does not fill:
•
•
•
•
• The machine fills then empties
immediately:
• The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage” section.
• The machine does not empty and/or
does not spin:
• The drain hose is squashed or kinked. (E20)
• The option NIGHT WASH or NO SPIN has been
selected.
• The drain filter is clogged. (E20)
• There is water on the floor:
• Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this
as the water runs down the hose; check to see if it
is damp.
• The drain hose is damaged.
• Unsatisfactory washing results:
• Too little detergent or unsuitable detergent has
been used.
• Stubborn stains have not been treated prior to
washing.
• The correct temperature/fabric was not selected.
• Excessive laundry load.
• The machine vibrates or is noisy:
• The transit bolts and packing have not been
removed.
• The support feet have not been adjusted.
• The laundry is not evenly distributed in the drum.
• Maybe there is very little laundry in the drum.
• The door will not open (the relevant
light is on):
•
•
•
•
48
The water tap is closed. (E10)
The inlet hose is squashed or kinked. (E10)
The filter in the inlet hose is blocked. (E10)
The door is not properly closed. (E40)
The programme is still running, the drum is turning.
The door lock has not yet released.
The water level is above the bottom edge of the door.
The machine is heating the water.
10/31/02
9:09 AM
Pagina
49
(Nero/Process Black pellicola)
Problem
Possible cause
• Spinning starts late or the laundry is
not spun enough:
• The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several
times before the unbalance disappears and normal
spinning can resume. If, after few minutes, the
laundry is still not evenly distributed in the drum,
the machine will spin at a lower speed or will not
spin. If at the end of the programme the laundry is
not spun enough, redistribute the load manually
and select the spin programme.
Water is not
visible in the machine. The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption. Performance is
nevertheless excellent.
The machine makes an unusual
noise. The machine is fitted with a commutator
motor which improves machine
performance.
P1035UK
P1034UK
Mo
Pro d. .....
d.
No .....
. .....
.....
.
Ser
. No
. .....
....
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase
date of your machine: the Service Centre will require
this information.
Mod. ..........
Prod. No. ...........
P0042 BD
49
Ser. No. .........
ENGLISH
132993430.qxd
132993430.qxd
10/31/02
9:09 AM
Pagina
50
(Nero/Process Black pellicola)
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement