Electrolux ESL5205LO User Manual

Add to my manuals
24 Pages

advertisement

Electrolux ESL5205LO User Manual | Manualzz
ESL5205LO
EN
Dishwasher
User Manual
2
www.electrolux.com
CONTENTS
1. SAFETY INFORMATION....................................................................................2
2. SAFETY INSTRUCTIONS..................................................................................4
3. PRODUCT DESCRIPTION................................................................................ 5
4. CONTROL PANEL............................................................................................. 6
5. PROGRAMMES................................................................................................. 6
6. SETTINGS..........................................................................................................7
7. BEFORE FIRST USE....................................................................................... 10
8. DAILY USE....................................................................................................... 11
9. HINTS AND TIPS............................................................................................. 13
10. CARE AND CLEANING..................................................................................14
11. TROUBLESHOOTING....................................................................................16
12. TECHNICAL INFORMATION......................................................................... 19
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that
brings with it decades of professional experience and innovation. Ingenious and
stylish, it has been designed with you in mind. So whenever you use it, you can
be safe in the knowledge that you’ll get great results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com/webselfservice
Register your product for better service:
www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
ENGLISH
3
responsible for any injuries or damages that are the
result of incorrect installation or usage. Always keep the
instructions in a safe and accessible location for future
reference.
1.1 Children and vulnerable people safety
•
•
•
•
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance when
the door is open.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
•
•
•
•
•
•
This appliance is intended to be used in household
and similar applications such as:
– farm houses; staff kitchen areas in shops, offices
and other working environments;
– by clients in hotels, motels, bed & breakfast and
other residential type environments.
Do not change the specification of this appliance.
The operating water pressure (minimum and
maximum) must be between 0.5 (0.05) / 8 (0.8) bar
(MPa)
Obey the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by
the manufacturer, its Authorised Service Centre or
similarly qualified persons in order to avoid a hazard.
Put the cutlery in the cutlery basket with the sharp
ends pointing down or put them in the cutlery drawer
in a horizontal position with the sharp edges down.
4
www.electrolux.com
•
•
•
•
•
Do not leave the appliance with the open door
unattended to avoid stepping accidentally onto it.
Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
Do not use high pressure water sprays and/or steam
to clean the appliance.
If the appliance has ventilation openings in the base,
they must not be covered e.g. by a carpet.
The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets must
not be reused.
2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged
appliance.
Do not install or use the appliance
where the temperature is less than 0
°C.
Follow the installation instruction
supplied with the appliance.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Make sure that the appliance is
installed below and adjacent to safe
structures.
•
•
•
•
•
•
2.2 Electrical connection
WARNING!
Risk of fire and electrical
shock.
•
•
•
The appliance must be earthed.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
Always use a correctly installed
shockproof socket.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to
the mains plug and to the mains
cable. Should the mains cable need to
be replaced, this must be carried out
by our Authorised Service Centre.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
This appliance complies with the
E.E.C. Directives.
Only for UK and Ireland. The
appliance has a 13 amp mains plug. If
it is necessary to change the fuse in
the mains plug, use fuse: 13 amp
ASTA (BS 1362).
2.3 Water connection
•
•
Do not cause damage to the water
hoses.
Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and
clear.
ENGLISH
•
•
Ensure that there are no visible water
leaks during and after the first use of
the appliance.
The water inlet hose has a safety
valve and a sheath with an inner
mains cable.
•
•
•
•
•
•
2.5 Disposal
WARNING!
Dangerous voltage.
If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the
mains socket. Contact the Authorised
Service Centre to replace the water
inlet hose.
WARNING!
Risk of injury or suffocation.
•
•
•
2.4 Use
•
Disconnect the appliance from the
mains supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent
children and pets to get closed in the
appliance.
Do not sit or stand on the open door.
3. PRODUCT DESCRIPTION
1
2
11
10
9
1 Upper spray arm
8 7
5
Dishwasher detergents are
dangerous. Obey the safety
instructions on the detergent
packaging.
Do not drink and play with the water in
the appliance.
Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may
remain on the dishes.
The appliance can release hot steam
if you open the door while a
programme operates.
Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
6
5
4
3
2 Lower spray arm
6
www.electrolux.com
3
4
5
6
7
Filters
Rating plate
Salt container
Air vent
Rinse aid dispenser
8
9
10
11
Detergent dispenser
Cutlery basket
Lower basket
Upper basket
4. CONTROL PANEL
1
2
5
1 On/off button
2 Programme indicators
3 Indicators
4
3
4 Programme button
5 Delay button
4.1 Indicators
Indicator
Description
End indicator.
Rinse aid indicator. It is always off while the programme operates.
Salt indicator. It is always off while the programme operates.
5. PROGRAMMES
Programme
2)
Degree of soil Programme
Type of load phases
Consumption values
1)
Duration
(min)
Energy
(kWh)
Water
(l)
1.039
11
Normal soil
Crockery and
cutlery
•
•
•
•
Prewash
Wash 50 °C
Rinses
Dry
227
Heavy soil
Crockery, cut‐
lery, pots and
pans
•
•
•
•
Prewash
Wash 70 °C
Rinses
Dry
155 - 170 1.5 - 1.7
14-15
ENGLISH
Programme
Degree of soil Programme
Type of load phases
Consumption values
1)
Duration
(min)
3)
4)
7
Energy
(kWh)
Water
(l)
Normal soil
Crockery and
cutlery
•
•
•
•
Prewash
Wash 65 °C
Rinses
Dry
130 - 140 1.4 - 1.6
15-17
Fresh soil
Crockery and
cutlery
•
30
0.8
10
•
Wash 60 °C
or 65 °C
Rinses
All
•
Prewash
14
0.1
5
1) The pressure and the temperature of the water, the variations of the mains supply, the
options and the quantity of dishes can change the values.
2) With this programme you have the most efficient use of water and energy consumption
for crockery and cutlery with normal soil. (This is the standard programme for test institutes).
3) With this programme you can wash a load with fresh soil. It gives good washing results in
a short time.
4) Use this programme to quickly rinse the dishes. this prevents the remaining food to bond
on the dishes and bad odours to come out from the appliance. Do not use detergent with
this programme.
5.1 Information for test
institutes
For all the necessary information for test
performance, send an email to:
[email protected]
Write down the product number (PNC)
that is on the rating plate.
6. SETTINGS
6.1 Programme selection mode
and user mode
When the appliance is in programme
selection mode it is possible to set a
programme and to enter the user mode.
Settings available in the user mode:
• The level of water softener according
to the water hardness.
• Activation or deactivation of the
acoustic signal for the end of a
programme.
• Activation or deactivation of AirDry.
As the appliance stores the saved
settings, there is no need to configure
it before every cycle.
How to set the programme
selection mode
The appliance is in programme selection
mode when the programme indicator
is blinking.
When you activate the appliance, usually
it is in programme selection mode.
However, if this does not happen, you
can set the programme selection mode
in the following way:
Press and hold the programme button
until the appliance is in programme
selection mode.
8
www.electrolux.com
6.2 The water softener
The water softener removes minerals
from the water supply, which would have
a detrimental effect on the washing
results and on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness
is measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water
in your area. It is important to set the
right level of the water softener to assure
good washing results.
Water hardness
German de‐
grees (°dH)
French de‐
grees (°fH)
mmol/l
Clarke de‐
grees
Water softener
level
47 - 50
84 - 90
8.4 - 9.0
58 - 63
10
43 - 46
76 - 83
7.6 - 8.3
53 - 57
9
37 - 42
65 - 75
6.5 - 7.5
46 - 52
8
29 - 36
51 - 64
5.1 - 6.4
36 - 45
7
23 - 28
40 - 50
4.0 - 5.0
28 - 35
6
19 - 22
33 - 39
3.3 - 3.9
23 - 27
5 1)
15 - 18
26 - 32
2.6 - 3.2
18 - 22
4
11 - 14
19 - 25
1.9 - 2.5
13 - 17
3
4 - 10
7 - 18
0.7 - 1.8
5 - 12
2
<4
<7
<0.7
<5
1 2)
1) Factory setting.
2) Do not use salt at this level.
Whether you use a standard detergent
or multi-tabs (with or without salt), set
the proper water hardness level to
keep the salt refill indicator active.
Multi-tabs containing salt are
not effective enough to
soften hard water.
How to set the water softener
level
The appliance must be in programme
selection mode.
1. To enter the user mode, press and
hold the programme button until the
indicator
indicator
flashes and the
and
are on.
2. Wait until the indicators
are off and the indicator
and
flashes.
The indicator
still flashes.
The intermittent flashing of the
shows the current
indicator
setting.
• e.g. 5 flashes + pause + 5 flashes
= level 5.
3. Press programme button repeatedly
to change the setting. Each pressing
of the programme button increases
the level number. After reaching level
10, the count starts again from level
1.
4. Press the on/off button to confirm the
setting.
ENGLISH
9
6.3 Acoustic signals
Acoustic signals sound when a
malfunction of the appliance occurs. It is
not possible to deactivate these acoustic
signals.
There is also an acoustic signal that
sounds when the programme is
completed. By default this acoustic signal
is deactivated but it is possible to
activate it.
How to activate the acoustic
signal for the end of
programme
During the drying phase, the
door opens automatically
and remains ajar.
The appliance must be in programme
selection mode.
CAUTION!
Do not try to close the
appliance door within 2
minutes after automatic
opening. This can cause
damage to the appliance.
1. To enter the user mode, press and
hold the programme button until the
flashes and
indicator
indicators
and
are on.
2. Press the programme button
immediately.
•
The indicator
on.
and
•
The indicator
flashes.
3. Wait until the indicator
are off. The indicator
flashes.
•
The
AirDry is automatically activated with all
are
programmes excluding
CAUTION!
If children have access to
the appliance, it is advised to
deactivate AirDry as opening
the door may pose a danger.
and
still
indicator shows the
current setting:
off = Acoustic
signal off.
4. Press the programme button to
change the setting.
on = Acoustic signal on.
•
5. Press on/off confirm the setting.
6.4 AirDry
AirDry improves the drying results with
less energy consumption.
.
How to deactivate AirDry
The appliance must be in programme
selection mode.
1. To enter the user mode, press and
hold the programme button until the
indicator
flashes and
indicators
and
are on.
2. Press the programme button twice.
•
The indicator
are on.
and
•
The indicator
flashes.
and
3. Wait until the indicator
are off. The indicator
flashes.
•
The
still
indicator shows the
current setting:
deactivated.
off = AirDry is
10
www.electrolux.com
4. Press the programme button to
change the setting.
•
on =AirDryis activated .
5. Press on/off to confirm the setting.
7. BEFORE FIRST USE
1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the
baskets.
After starting a programme, it may take
up to 5 minutes for the appliance to
recharge the resin in the water softener.
It seems that the appliance is not
working. The washing phase starts only
after this procedure is completed. The
procedure is repeated periodically.
4. Carefully shake the funnel by its
handle to get the last granules inside.
5. Remove the salt around the opening
of the salt container.
7.1 The salt container
CAUTION!
Use rough salt designed for
dishwashers only. Fine salt
increases the risk of
corrosion.
The salt is used to recharge the resin in
the water softener and to assure good
washing results in daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt
container (only for the first time).
3. Fill the salt container with 1 kg of salt
(until it is full).
6. Turn the cap of the salt container
clockwise to close the salt container.
CAUTION!
Water and salt can come out
of the salt container when
you fill it. After you fill the
salt container, immediately
start a programme to
prevent corrosion.
ENGLISH
7.2 How to fill the rinse aid
dispenser
A D
CAUTION!
Only use rinse aid
specifically designed for
dishwashers.
B
C
M AX
4
1
3 2
+
1. Press the release button (D) to open
the lid (C).
2. Pour the rinse aid in the dispenser
(A) until the liquid reaches the fill
level 'max'.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4. Close the lid. Make sure that the
release button locks into position.
You can turn the selector of
the released quantity (B)
between position 1 (lowest
quantity) and position 4 or 6
(highest quantity).
B
A
11
-
C
D
8. DAILY USE
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in
programme selection mode.
• If the salt indicator is on, fill the
salt container.
• If the rinse aid indicator is on, fill
the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme
for the type of load and the degree of
soil.
8.1 Using the detergent
D A B
30
20
C
12
www.electrolux.com
A
30
B
Starting a programme with
delay start
D
1. Set a programme.
2. Press Delay to delay the start of the
programme of 3 hours.
20
C
1. Press the release button (B) to open
the lid (C).
2. Put the detergent, in powder or
tablets, in the compartment (A).
3. If the programme has a prewash
phase, put a small quantity of
detergent in the compartment (D).
4. Close the lid. Make sure that the
release button locks into position.
8.2 Using the multi-tablets
When you use tablets, that contain salt
and rinse aid, do not fill the salt container
and the rinse aid dispenser.
1. Adjust the water softener to the
lowest level.
2. Set the rinse aid dispenser to the
lowest position.
8.3 Setting and starting a
programme
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate the
appliance. Make sure that the
appliance is in programme selection
mode.
3. Press the programme button
repeatedly until the indicator of the
programme you want to select starts
flashing.
4. Close the appliance door to start the
programme.
• The indicator
comes on.
3. Close the appliance door to start the
countdown.
When the countdown is completed, the
programme starts.
Opening the door while the
appliance operates
Opening the door while a programme is
running stops the appliance. It may affect
the energy consumption and the
programme duration. After closing the
door, the appliance continues from the
point of interruption.
If the door is opened for
more than 30 seconds
during the drying phase, the
running programme ends. It
does not happen if the door
is opened by AirDry function.
Do not try to close the
appliance door within 2
minutes after AirDry
automatically opens it, as
this may cause damage to
the appliance.
If, afterwards, the door is
closed for another 3
minutes, the running
programme ends.
Cancelling the delay start
Press and hold the programme button
until the appliance is in programme
selection mode.
When you cancel the delay start, you
have to set the programme again.
ENGLISH
Cancelling the programme
Press and hold the programme button
until the appliance is in programme
selection mode.
Make sure that there is detergent in the
detergent dispenser before you start a
new programme.
13
1. Press the on/off button or wait for the
appliance to switch to standby mode.
If you open the door before the
activation of standby mode, the
appliance is automatically
deactivated.
2. Close the water tap.
End of the programme
When the programme is completed the
indicator
is on.
9. HINTS AND TIPS
9.1 General
•
The following hints will ensure optimal
cleaning and drying results in daily use
and also help to protect the environment.
•
•
•
•
•
•
Remove larger residues of food from
the dishes into the waste bin.
Do not pre-rinse dishes by hand.
When needed, use the prewash
programme (if available) or select a
programme with a prewash phase.
Always use the whole space of the
baskets.
When loading the appliance, make
sure that the dishes can be
completely reached and washed by
the water released from the spray arm
nozzles. Make sure that items do not
touch or cover each other.
You can use dishwasher detergent,
rinse aid and salt separately or you
can use the multi-tablets (e.g. ''3in1'',
''4in1'', ''All in 1''). Follow the
instructions written on the packaging.
Select the programme according to
the type of load and degree of soil.
With the ECO programme you have
the most efficient use of water and
energy consumption for crockery and
cutlery with normal soil.
9.2 Using salt, rinse aid and
detergent
•
Only use salt, rinse aid and detergent
for dishwasher. Other products can
cause damage to the appliance.
•
•
•
In areas with hard and very hard
water we recommend to use plain
dishwasher detergent (powder, gel,
tablets containing no additional
agents), rinse aid and salt separately
for optimal cleaning and drying
results.
At least once a month run the
appliance with the use of appliance
cleaner which is particularly suitable
for this purpose.
Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use the
tablets with long programmes.
Do not use more than the correct
quantity of detergent. Refer to the
instructions on the detergent
packaging.
9.3 What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according
to the water hardness in your area.
14
www.electrolux.com
5. Adjust the released quantity of rinse
aid.
9.4 Loading the baskets
•
•
•
•
•
•
•
•
•
•
Only use the appliance to wash items
that are dishwasher-safe.
Do not put in the appliance items
made of wood, horn, aluminium,
pewter and copper.
Do not put in the appliance items that
can absorb water (sponges,
household cloths).
Remove larger residues of food from
the dishes into the waste bin.
Make soft the remaining burned food
on the items.
Put hollow items (cups, glasses and
pans) with the opening down.
Make sure that glasses do not touch
other glasses.
Put cutlery and small items in the
cutlery basket.
Put light items in the upper basket.
Make sure that the items do not
move.
Make sure that the spray arms can
move freely before you start a
programme.
•
•
•
•
•
•
•
The filters are clean and correctly
installed.
The cap of the salt container is tight.
The spray arms are not clogged.
There is dishwasher salt and rinse aid
(unless you use multi- tablets).
The position of the items in the
baskets is correct.
The programme is applicable for the
type of load and for the degree of soil.
The correct quantity of detergent is
used.
9.6 Unloading the baskets
1. Let the tableware cool down before
you remove it from the appliance. Hot
items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
At the end of the program
water can still remain on the
sides and on the door of the
appliance.
9.5 Before starting a
programme
Make sure that:
10. CARE AND CLEANING
WARNING!
Before maintenance,
deactivate the appliance and
disconnect the mains plug
from the main socket.
C
Dirty filters and clogged
spray arms decrease the
washing results. Make a
check regularly and, if
necessary, clean them.
B
10.1 Cleaning the filters
A
The filter system is made of 3 parts.
1. Turn the filter (B) counterclockwise
and remove it.
ENGLISH
15
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter
(A). Turn it clockwise until it locks.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
CAUTION!
An incorrect position of the
filters can cause bad
washing results and damage
to the appliance.
10.2 Cleaning the spray arms
Do not remove the spray arms. If the
holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.
10.3 External cleaning
5. Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter (A).
Make sure that it is correctly
positioned under the 2 guides.
•
•
•
Clean the appliance with a moist soft
cloth.
Only use neutral detergents.
Do not use abrasive products,
abrasive cleaning pads or solvents.
10.4 Internal cleaning
•
Carefully clean the appliance,
including the rubber gasket of the
door, with a soft damp cloth.
16
www.electrolux.com
•
If you regularly use short duration
programmes, these can leave
deposits of grease and limescale
inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per
month.
•
To maintain the performance of your
appliance at its best, we recommend
to use monthly a specific cleaning
product for dishwashers. Follow
carefully the instructions on the
packaging of the product.
11. TROUBLESHOOTING
If the appliance does not start or it stops
during operation, before you contact an
Authorised Service Centre, check if you
can solve the problem by yourself with
the help of the information in the table.
WARNING!
Repairs not properly done
may result in serious risk to
the safety of the user. Any
repairs must be performed
by qualified personnel.
With some problems the end indicator
flashes intermittently indicating a
malfunction.
The majority of problems that can
occur can be solved without the need
to contact an Authorised Service
Centre.
Problem and alarm code
Possible cause and solution
You cannot activate the appliance.
•
•
The programme does not start.
•
•
•
The appliance does not fill with wa‐
ter.
• The end indicator flashes 1 time
intermittently.
• Acoustic signal sounds 1 time in‐
termittently.
•
•
•
•
•
The appliance does not drain the
•
water.
• The end indicator flashes 2 times •
intermittently.
• Acoustic signal sounds 2 times
intermittently.
Make sure that the mains plug is connected
to the mains socket.
Make sure that there is no damaged fuse in
the fuse box.
Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or
wait for the end of the countdown.
The appliance has started the procedure to
recharge the resin inside the water softener.
The duration of the procedure is approxi‐
mately 5 minutes.
Make sure that the water tap is open.
Make sure that the pressure of the water
supply is not too low. For this information,
contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is
not clogged.
Make sure that the inlet hose has no kinks
or bends.
Make sure that the sink spigot is not clog‐
ged.
Make sure that the drain hose has no kinks
or bends.
ENGLISH
Problem and alarm code
17
Possible cause and solution
The anti-flood device is on.
•
• The end indicator flashes 3 times
intermittently.
• Acoustic signal sounds 3 times
intermittently.
Close the water tap and contact an Author‐
ised Service Centre.
The appliance stops and starts
more times during operation.
•
It is normal. It provides optimal cleaning re‐
sults and energy savings.
The program lasts too long.
•
If the delayed start option is set, cancel the
delay setting or wait for the end of the
countdown.
Small leak from the appliance door.
•
The appliance is not levelled. Loosen or
tighten the adjustable feet (if applicable).
The appliance door is not centred on the
tub. Adjust the rear foot (if applicable).
•
The appliance door is difficult to
close.
•
Rattling/knocking sounds from in‐
side the appliance.
•
•
•
The appliance trips the circuit-beak‐ •
er.
•
Refer to "Before first use",
"Daily use", or "Hints and
tips" for other possible
causes.
Once you have checked the appliance,
deactivate and activate the appliance. If
The appliance is not levelled. Loosen or
tighten the adjustable feet (if applicable).
Parts of the tableware are protruding from
the baskets.
The tableware is not properly arranged in
the baskets. Refer to basket loading leaflet.
Make sure that the spray arms can rotate
freely.
The amperage is insufficient to supply si‐
multaneously all the appliances in use.
Check the socket amperage and the capaci‐
ty of the meter or turn off one of the applian‐
ces in use.
Internal electrical fault of the appliance.
Contact an Authorised Service Centre.
the problem occurs again, contact an
Authorised Service Centre.
For alarm codes not described in the
table, contact an Authorised Service
Centre.
18
www.electrolux.com
11.1 The washing and drying results are not satisfactory
Problem
Possible cause and solution
Poor washing results.
•
•
•
Poor drying results.
•
•
•
•
Refer to "Daily use", "Hints and tips" and basket
loading leaflet.
Use more intensive washing programmes.
Clean spray arm jets and filter. Refer to "Care and
Cleaning".
Tableware has been left for too long inside a
closed appliance.
There is no rinse aid or the dosage of rinse aid is
not enough. Set the rinse aid dispenser to a higher
level.
Plastic items may need to be towel dried.
We recommend to always use rinse aid, even in
combination with multi-tablets.
There are whitish streaks or •
bluish layers on glasses and
dishes.
•
The release quantity of rinse aid is too much. Ad‐
just the rinse aid level to a lower level.
The quantity of detergent is too much.
There are stains and dry wa‐ •
ter drops on glasses and
dishes.
•
The released quantity of rinse aid is not sufficient.
Adjust the rinse aid level to a higher level.
The quality of the rinse aid can be the cause.
The dishes are wet.
The programme does not have a drying phase or
has a drying phase with low temperature.
The rinse aid dispenser is empty.
The quality of the rinse aid can be the cause.
The quality of the multi-tablets can be the cause.
Try a different brand or activate the rinse aid dis‐
penser and use rinse aid and multi-tablets together.
•
•
•
•
The interior of the appliance
is wet.
•
This is not a defect of the appliance. it is caused by
the humidity in the air that condenses on the walls.
Unusual foam during wash‐
ing.
•
•
Use the detergent for dishwashers only.
There is a leak in the rinse aid dispenser. Contact
an Authorised Service Centre.
Traces of rust on cutlery.
•
There is too much salt in the water used for wash‐
ing. Refer to "The water softener".
Silver and stainless steel cutlery were placed to‐
gether. Avoid to put silver and stainless steel items
close together.
•
There are residues of deter‐
gent in the dispenser at the
end of the programme.
•
•
•
The detergent tablet got stuck in the dispenser and
therefore was not completely washed away by wa‐
ter.
Water cannot wash away the detergent from the
dispenser. Make sure that the spray arm is not
blocked or clogged.
Make sure that items in the baskets do not impede
the lid of the detergent dispenser from opening.
ENGLISH
Problem
19
Possible cause and solution
Odours inside the appliance. •
Refer to "Internal cleaning".
Limescale deposits on the
•
tableware, on the tub and on •
the inside of the door.
•
The level of salt is low, check the refill indicator.
The cap of the salt container is loose.
Your tap water is hard. Refer to "The water soft‐
ener".
Even using multi-functional tabs use salt and set
regeneration of the water softener. Refer to "The
water softener".
If lime scale deposits still remain, clean the appli‐
ance with appliance cleaners which are particularly
suitable for this purpose.
Try different detergent.
Contact the detergent manufacturer.
•
•
•
•
Dull, discoloured or chipped
tableware.
•
•
•
Make sure that only dishwasher-safe items are
washed in the appliance.
Load and unload the basket carefully. Refer to bas‐
ket loading leaflet.
Place delicate items in the upper basket.
Refer to "Before first use",
"Daily use" or "Hints and
tips" for other possible
causes.
12. TECHNICAL INFORMATION
Dimensions
Width / height / depth
(mm)
596 / 818 - 898 / 550
Electrical connection 1)
Voltage (V)
220 - 240
Frequency (Hz)
50
Water supply pressure
Min. / max. bar (MPa)
0.5 (0.05) / 8 (0.8)
Water supply
Cold water or hot water 2) max 60 °C
Capacity
Place settings
13
Power consumption
Left-on mode (W)
5.0
Power consumption
Off-mode (W)
0.50
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian ener‐
gy), use the hot water supply to decrease energy consumption.
13. ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol
. Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to
20
www.electrolux.com
recycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol
with the
*
household waste. Return the product to
your local recycling facility or contact
your municipal office.
ENGLISH
21
22
www.electrolux.com
ENGLISH
23
156915580-A-102017
www.electrolux.com/shop

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement