Advertisement
Advertisement
User manual Dishwasher ZDI430 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ 16 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Unloading the dishwasher _ _ _ _ _ _ _ _ 17 Washing programmes _ _ _ _ _ _ _ _ _ _ _ 8 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ 17 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Environmental concerns _ _ _ _ _ _ _ _ _ 19 Set the water softener _ _ _ _ _ _ _ _ _ _ 10 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20 Filling with dishwasher salt _ _ _ _ _ _ _ _ 12 Consumption values _ _ _ _ _ _ _ _ _ _ _ 21 Filling with rinse aid _ _ _ _ _ _ _ _ _ _ _ 12 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ 22 Adjusting the dosage of rinse aid _ _ _ _ 13 Hints for test institutes _ _ _ _ _ _ _ _ _ _ 22 Load cutlery and dishes _ _ _ _ _ _ _ _ _ 13 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 23 Subject to change without notice 2 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. Correct use • This dishwasher is only intended for washing household utensils suitable for machine washing. • Do not put any solvents in the dishwasher. This could cause an explosion. • Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket. • Only use products (detergent, salt and rinse aid) suitable for dishwashers. • Avoid opening the door whilst the appliance is in operation, hot steam may escape. • Do not take any dishes out of the dishwasher before the end of the dishwashing cycle. • After use, isolate the appliance from the power supply and turn off the water supply. • This product should be serviced only by an authorised service engineer, and only genuine spare parts should be used. • Under no circumstances should you attempt to repair the machine yourself. Repairs car- ried out by inexperienced persons will cause injury or serious malfunctioning. Contact your local Service Force Centre. Always insist on genuine spare parts. General safety • Dishwasher detergents can cause chemical burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer. • The water in your dishwasher is not for drinking. Detergent residues may still be present in your machine. • Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves. • Do not sit or stand on the open door. Child safety • This appliance is designed to be operated by adults. Don’t allow children to use the dishwasher unsupervised. • Keep all packaging well away from children. There is risk of suffocation. • Keep all detergents in a safe place out of children’s reach. • Keep children well away from the dishwasher when the door is open. 3 Installation • Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. • All packaging must be removed before use. • Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. • For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. • Never use the dishwasher if the electrical supply cable and water hoses are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Contact your local Service Force centre, in order to avoid hazard. • All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components. WARNING! For electrical and water connection carefully follow the instructions given in specific paragraphs. Control panel 1 2 3 4 5 6 A B 7 4 C 1. 2. 3. 4. 5. 6. 7. Up and down programme selection buttons Half load button Delay start button Digital display Indicator lights On/Off button Function buttons Setting mode Press the On/Off button; if the On/Off indicator light illuminates, the indicator lights of the programme selection buttons are illuminated and in the digital display are visible 2 horizontal lines (- -) the appliance is in setting mode. Always remember that when performing the following operations: – selecting a washing programme, – setting the water softener level, the appliance MUST be in setting mode. Press the On/Off button; If other button indicator lights are on and in the digital display is visible the number of a programme (1 - 2 - 3 etc..), this means that a washing programme has been set. In this case, to return to setting mode, the programme has to be cancelled (see instructions “Cancel a washing programme in progress”). Digital display In the digital display is indicated: – the level of hardness to which the water softener is set, – the number corresponding to the selected washing programme, – the approximate remaining time of the running programme, – the countdown of the delay start, – fault codes concerning malfunction of the appliance. Function buttons In addition to the dishwashing programme selection and the half load option, the following functions can also be set with the help of these buttons. – the setting of the water softener, – the cancelling of a programme in progress, 5 Up and down programme selection buttons 6 Using these two buttons you have an increasing or a decreasing order in the selection of the programme (see "Washing programmes" chart for the number of the programme). • Starting the washing programme: 1. Press the On/Off button. The On/Off light will illuminate and the indicator lights of the programme selection buttons will illuminate and in the digital display are visible 2 horizontal lines (-). 2. To select a programme, press either one of the two programme selection buttons, until the number of chosen programme appears on the display. 3. Select if desired, within 3 seconds, the half load option (check that the option is available with the selected washing programme). 4. After about 3 seconds from the last pressure of a button the programme starts automatically. In the digital display appears the running time of the programme and the indicator lights of the programme selection buttons remain illuminated with a fixed light. • Cancel the washing programme in progress: 1. Press the function buttons B and C simultaneously for about 2 seconds, the indicator lights of the programme selection buttons will start flashing. After about 2 seconds the indicator lights of the programme selection buttons will illuminate with a fixed light and 2 horizontal lines (- -) will appear in the digital display. 2. Switch off the machine by pressing the On/Off button or select a new washing programme (check that there is detergent in the detergent dispenser. Half load button The option must be linked to the selection of a washing programme. (See "Programme table" chart). When selected, the corresponding light illuminates. Load dishes in both baskets (lower and upper). When using the option reduce the dosage of detergent which is normally used for a complete load. Delay start button This option allows the start of the programme to be delayed from 1 to 19 hours. After having selected the washing programme press the delay start button until the flashing number of the hours for the delay start will appear in the digital display. As soon as the number of hours is displayed without flashing, the countdown for the delay start is active. The countdown will decrease with steps of 1 hour. Once the delay start has elapsed the programme will start automatically. Cancel the delay start in progress: To cancel a delay start in progress you have to reset the dishwasher; follow the same instructions given in "Cancel the washing programme in progress". IMPORTANT! Cancelling a delay start involves also the cancelling of the washing programme set. In this case you have to select the washing programme again. IMPORTANT! It is possible to select a washing programme and the delay start also with the door slightly opened. In this case the start of the programme or the countdown will occur after the closure of the door. Until that moment it is possible to modify the set made. Indicator lights Wash Illuminates when the washing and rinsing phases are running. Dry Illuminates when the drying phase is running. 7 Indicator lights End of programme Illuminates when the washing programme has ended. It also has added functions of visual signalling as: • the setting of the water softener, • intervention of an alarm due to the malfunction of the machine. Salt refilling 1) Illuminates when special salt needs to be filled. It can remain illuminated several hours after the salt has been filled. Rinse aid Illuminates when rinse aid needs to be filled. 1) 1) The salt and rinse aid indicator lights are never illuminated while a washing programme id running even if filling with salt and rinse aid is necessary. Washing programmes Programme Half load Degree of soil Type of load Programme description 1 Rinse and hold No Any. Partial load (to be completed later in the day). 1 cold rinse (to avoid food scraps from sticking together). This programme does not require the use of detergent. 2 Intensive 70° Yes Heavy soil Crockery, cutlery, pots and pans Prewash Main wash 2 intermediate rinses Final rinse Drying 3 Auto 45° -70° No Normal soil. Crockery and cutlery Prewash Main wash 1 or 2 intermediate rinses Final rinse Drying 8 1) Programme Half load Degree of soil Type of load Programme description 4 Quick 30 min. 65° No Light soil Crockery and cutlery Main wash Final rinse 5 Bio 50° Yes Normal soil Crockery and cutlery Prewash Main wash 1 intermediate rinse Final rinse Drying 6 Glass 45° No Normal soil Delicate crockery and glassware Main wash 1 intermediate rinse Final rinse Drying 2) 4) 3) 1) When the Half load button is pressed, the prewash phase will be automatically excluded. In this case the detergent dose for the prewash phase is no longer necessary. 2) Ideal for washing a partially loaded dishwasher. This is perfect daily programme, made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery. 3) Test programme for test institutes. 4) When the Half load button is pressed, the duration of the washing phase is reduced. "Auto" washing programme During the "Auto" washing programme the amount of soil on the dishes is determined by how cloudy the water is. If the appliance is partially loaded and the dishes lightly soiled, the "prewash", "main wash", and "rinse" phases of the programme are shorter and the water consumption level is lower. If the appliance is fully loaded and the dishes heavily soiled, the "prewash", "main wash", and "rinse" phases of the programme are longer and the water consumption level is higher. For this reason the programme duration, water and energy consumption levels can vary within the stated range for "Auto" programme (see "Washing programmes chart"). During the "Auto" programme the temperature of the main wash water is also automatically adjusted between 45°C and 70°C depending on the amount of soil on the dishes. First use Before using your dishwasher for the first time: • Ensure that the electrical and water connections comply with the installation instructions • Remove all packaging from inside the appliance • Set the water softener • Pour 1 litre of water inside the salt container and then fill with dishwasher salt • Fill the rinse aid dispenser 9 – Set the water hardness to level 1. When using tablets that integrate rinse aid and detergent: IMPORTANT! there is no need to fill up with rinse aid – set the water softener – add special (dishwasher) salt When using tablets that integrate rinse aid, detergent, salt function and other additives: there is no need to fill up with special salt or rinse aid. Check whether these detergents are suitable for your water hardness. Follow the manufacturers instructions. If the drying results are not satisfactory we recommend that you: 1. Fill up the rinse aid dispenser with rinse aid. 2. Set the rinse aid dosage to position 2. If you decide in future to use separated detergents, we advise that you: – Fill up the salt and rinse aid container. – Adjust the water hardness setting to the highest level and perform 1 normal washing programme without loading any dishes. – Adjust the water hardness setting according to the hardness of the water in your area. – Adjust the rinse aid dosage Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these minerals and salts, the harder your water is. Water hardness is measured in equivalent scales, German deWater hardness 10 grees (°dH), French degrees (°TH) and mmol/ l (millimol per litre - international unit for the hardness of water). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. Adjusting the water hardness setting Use of salt °dH °TH mmol/l manually electronically 51 - 70 91 - 125 9,1 - 12,5 2 level 10 yes 43 - 50 76 - 90 7,6 - 8,9 2 level 9 yes 37 - 42 65 - 75 6,5 - 7,5 2 level 8 yes Water hardness Adjusting the water hardness setting Use of salt °dH °TH mmol/l manually electronically 29 - 36 51 - 64 5,1 - 6,4 2 level 7 yes 23 - 28 40 - 50 4,0 - 5,0 2 level 6 yes 19 - 22 33 - 39 3,3 - 3,9 2 level 5 yes 15 - 18 26 - 32 2,6 - 3,2 1 level 4 yes 11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes 4 - 10 7 - 18 0,7 - 1,8 1 level 2 yes <4 <7 < 0,7 1 level 1 no The water softener must be set in both ways: manually, using the water hardness dial and electronically. Setting the water softener manually (see table) The water softener is factory set at position 2. Set switch to position 1 or 2 Setting the water softener electronically (see table) The water softener is factory set at position 5. 1. Press the On/Off button. The dishwasher must be in setting mode. 2. Simultaneously press and hold function buttons B and C, until the lights of function buttons A, B and C start flashing. 3. Press function button A, the lights of function buttons B and C turn off while the light of function button A goes on flashing. In the digital display is visible the current level. Examples: displayed = level 5 displayed = level 10 4. To change the level, press function button A. Each time the button is pressed the level 11 changes. (For the selection of the new level see the chart). Examples: if the current level is 5, by pressing function button A once, level 6 is selected. if the current level is 10, by pressing function button A once, level 1 is selected. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off button. Filling with dishwasher salt CAUTION! Use only special salt suitable for dishwashers. Unscrew the cap. Only before filling with Using the funnel provided, salt for the first time, fill pour in the salt until the the salt container with wa- container is filled with salt. ter. IMPORTANT! Immediately start a complete programme. IMPORTANT! Water will overflow from the container as salt is added. Remove any trace of salt. Replace the cap tightly turning it clockwise until it stops with a click. IMPORTANT! Top up the special salt when the light on the control panel illuminates. 12 Filling with rinse aid Open the lid. Fill up with rinse aid. The Clean up any rinse aid maximum level for filling is which overflows. Close the lid and press until it indicated by "max" locks. IMPORTANT! CAUTION! Top up the rinse aid when the light on the control panel Never fill the rinse aid dispenser with any other subilluminates. stances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance. Adjusting the dosage of rinse aid Increase the dose if there are drops of water or lime spots on the dishes after washing. Open the lid. Reduce the dose if there are whitish streaks on the dishes or a bluish film on glassware or knife blades. Set the dosage level. (The Close the lid and press undose is factory set in po- til it locks. sition 4). 13 Load cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. • Before loading the dishes, you should: – Remove all left over food and debris. – Soften remnants of burnt food in pans • When loading the dishes and cutlery, please note: – Dishes and cutlery must not impede the rotation of the spray arms. – Load hollow items such as cups, glasses, pans, etc. with the opening downwards so that water cannot collect in the container or a deep base. – Dishes and items of cutlery must not lie inside one another, or cover each other. – To avoid damage to glasses, they must not touch. – Lay small objects in the cutlery basket. • Plastic items and pans with non stick coatings have a tendency to retain water drops; these items will not dry as well as porcelain and steel items. • Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so they do not move. For washing in the dishwasher the following cutlery and dishes are not suitable: are of limited suitability: • Cutlery with wooden, horn, china or mother-ofpearls handles. • Plastic items that are not heat resistant. • Older cutlery with glued parts that are not temperature resistant. • Bonded cutlery items or dishes. • Pewter or copper items. • Lead crystal glass. • Steel items prone to rusting. • Wooden platters. • Items made from synthetics fibres. • Only wash stoneware in the dishwasher if it is specially marked as being dishwasher-safe by the manufacturer. • Glazed patterns may fade if machine washed frequently. • Silver and aluminium parts have a tendency to discolour during washing: Residues, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use. 14 Load cutlery. For best results we recommend you to use the cutlery grid provided (if the size and dimensions of the cutlery allow it) Place knives and other items of cutlery with sharp points or edges with their handles facing upwards. Risk of injury! Load the lower basket. Arrange serving dishes and large lids around the edge of the basket. The two rows of prongs on the lower basket can be easily lowered to allow you to load pots, pans and bowls. Load upper basket. Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so they do not move. For taller items, the cup racks can be folded upwards. If plates are to be loaded in the upper basket: load them starting from the rear positions; tilting them slightly forwards and avoiding the front positions near the door. 15 Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in : upper basket lower basket With upper basket raised 20 cm 31 cm With upper basket lowered 24 cm 27 cm To move to the higher position proceed as follows: 1. Pull out the basket until it stops. 2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable. To lower the basket to the original position proceed as follows: 1. Pull out the basket until it stops. 2. Carefully lift both sides upwards and then allow the mechanism to drop back down slowly, keeping hold of it. IMPORTANT! Never lift or lower the basket on one side only Use of detergent IMPORTANT! Only use detergents suitable for dishwashers. 16 IMPORTANT! When the basket is in the higher position you will not be able to use the cup racks. Observe the manufacturer’s dosing and storage recommendations. Open the lid. Fill in the detergent in compartment A. Observe the dosing levels. For programmes with pre- When using detergent Close the lid. wash add an additional tablets: place detergent detergent dose in comtablets in compartment A. partmentB. Detergent tablets Detergent tablets from different manufacturers dissolve at different rates. For this reason, some detergent tablets do not attain their full Unloading the dishwasher • Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing from the appliance. • Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. cleaning power during short washing programmes. Therefore, please use long washing programmes when using detergent tablets, to ensure the complete removal of detergent residuals. • Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler than the dishes. CAUTION! When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off. 17 Care and cleaning Cleaning the filters IMPORTANT! NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the thoroughly under running turn anticlockwise and re- base of the washing comwater. move filters B and C. partment. Put the flat filter A back in Replace the filters and the base of the washing lock by turning the handle compartment and ensure clockwise to the stop. that it fits perfectly under the two guidesD. Cleaning the spray arms External cleaning NEVER try to remove the spray arms. Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....). If residues of soil have clogged the holes in the spray arms, remove them with a cocktail stick. 18 Internal cleaning Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run the wash programme for heavy soiled dishes using detergent but without dishes. Prolonged periods of nonoperation If you are not using the machine for any prolonged period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3. Leave the inside of the machine clean. able, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc....): 1. Unplug it. 2. Turn the water tap off. 3. Remove the water inlet and discharge hoses. 4. Pull the machine out together with the hoses. Avoid over tilting the machine during transportation. Frost precautions Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoid- Environmental concerns Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. CAUTION! When a unit is no longer being used: • Pull the plug out of the socket. • Cut off the cable and plug and dispose of them. • Dispose of the door catch. This prevents children from trapping themselves inside and endangering their lives. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused 19 by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local coun- cil, your household waste disposal service or the shop where you purchased the product. The dishwasher will not start or stops during operation. Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the indications described in the chart, without calling out an engineer. Switch off the dishwasher and carry out the following suggested corrective actions. What to do if… Fault code and malfunction Possible cause and solution • appears in the digital display. • intermittent audible signal The dishwasher does not fill with water. • The water tap is blocked or furred with limescale. Clean the water tap. • The water tap is turned off. Turn the water tap on. • The filter (where present) in the threaded hose fitting at the water inlet valve is blocked. Clean the filter in the threaded hose. • The water inlet hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. • appears in the digital display. • intermittent audible signal The dishwasher will not drain. • The sink spigot is blocked. Clean out the sink spigot. • The water drain hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. • appears in the digital display. • intermittent audible signal Anti-flood device is activated. • Close the water tap and contact your local Service Force Centre. The programme does not start. • The dishwasher’s door has not been properly closed. Close the door. • The main plug is not plugged in. Insert the main plug. • The fuse has blown out in the household fuse box. Replace the fuse. • Delay start has been set. If dishes are to be washed immediately, cancel the delay start. Once these checks have been carried out; switch on the dishwasher. The programme will 20 continue from the point at which it was interrupted. If the malfunction or fault code reappears contact the Service Force Centre. For other fault codes not described in the above chart, please contact your Service Force Centre. Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC) and serial number (S.N.). This information can be found on the rating plate located on the side of the dishwasher door.. So that you always have these numbers at hand, we recommend you to make a note of them here: Mod. :. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The wash results are not satisfactory The dishes are not clean • The wrong washing programme has been selected. • The dishes are arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded. • The spray arms do not rotate freely due to incorrect arrangement of the load. • The filters in the base of the washing compartment are dirty or incorrectly positioned. • Too little or no detergent has been used. • Where there are limescales deposits on the dishes; the salt container is empty or the incorrect level of the water softener has been set. • The drain hose connection is not correct. • The salt container cap is not properly closed. The dishes are wet and dull • Rinse aid was not used. • The rinse aid dispenser is empty. There are streaks, milky spots or a bluish coating on glasses and dishes • Decrease rinse aid dosing. Water drops have dries onto glasses and dishes • Increase rinse aid dosing. • The detergent may be the cause. Contact the detergent manufacturer’s consumer care line. If after all these checks, the problem persists, contact your local Service Force Centre. 21 Consumption values iations of the power supply and the amount of dishes. The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the var- Consumption values Programme Programme duration (in Energy consumption (in minutes) kWh) Water (litres) 1 Rinse and Hold 12 0,1 4 2 Intensive 70° 80-90 1,6-1,8 22-24 3 Auto 45°-70° 90-140 1,1-1,8 12-23 4 Quick 30min.65° 30 0,9 9 5 BIO 50° (Test programme for Test Institutes) 160 1,05 13 6 Glass 45° 60-70 0,8-0,9 14-15 Technical data Dimensions Width x Height x Depth cm 59,6 x 81,8-87,8 x 57,5 Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher’s door. Water supply pressure Minimum - Maximum (MPa) 0,05 - 0,8 Capacity place settings 12 Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Consumption values"). Test in accordance with EN 50242 must be carried out when the salt container and rinse 22 aid dispenser have been filled with salt and rinse aid respectively and using the test programme (see "Consumption values"). Full load: 12 standard place settings Amount of detergent required 5 g + 25 g (Type B) Rinse aid setting position 4 (Type III) Upper basket Cutlery basket Lower basket cup racks: position A Installation WARNING! Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. however, depends on how the hot water is produced. (We suggest alternative sources of energy that are more environmentally friendly as e.g. solar or photovoltaic panels and aeolian). Water connection WARNING! Only use, for connection to the water mains, new hose-set; old hose-set must not be reused. WARNING! This appliance can be connected to either a hot (max. 60°) or cold water supply. With a hot water supply you can have a significant reduction of energy consumption. This CAUTION! If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. 23 Water inlet hose with safety valve Connect the inlet hose to a water tap with an external thread of 3/4”. After connecting the double-walled water inlet hose, the safety valve is next to the tap. If the water inlet hose leaks, the safety valve cuts off the water supply. WARNING! The electrical cable for the safety valve is in the double-walled water inlet hose and is live. Therefore do not immerse the water inlet hose or the safety valve in water. Take care when installing the water inlet hose . Place the water inlet hose in such a way that it is always lower than the bottom edge of the safety valve. If the water inlet hose or the safety valve is damaged, remove the mains plug immediately. CAUTION! A water inlet hose with safety valve MUST only be replaced by your local Service Force Centre. Drain hose Connect drain hose to the Required height: 30 to 100 Ensure that the hoses are When connecting the sink. cm above bottom of the not kinked, crushed or en- drain hose to an under dishwasher. tangled. sink trap spigot, the entire plastic membrane (A) must be removed. Failure to remove all the membrane will result in food particles building up over time eventually blocking the dishwasher drain hose spigot. If you use a drain hose extension the total length should not be longer than 4 metres. 24 Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided. CAUTION! To avoid water leakage after installation make sure that the water couplings are tight. Electrical connection CAUTION! Safety standards require the appliance to be earthed. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs, connectors and extension cables must not be used. This could constitute a fire hazard through overheating. If necessary, have the domestic wiring system socket replaced. In case that the electrical cable has to be replaced, contact your local Service Force centre. The plug must be accessible after the appliance has been installed. Never unplug the appliance by pulling on the cable. Always pull the plug. The manufacturer accepts no liability for failure to observe the above safety precautions. Fitting under a counter IMPORTANT! Carefully follow the instructions on the enclosed template for building in the dishwasher and fitting the furniture panel. WARNING! The dishwasher must be secured against tilting. Therefore make sure that the counter it is fixed under, is suitably secured to a fixed structure (adjacent kitchen units cabinets, wall). This dishwasher is designed to be fitted under a kitchen counter or work surface. No further openings for the venting of the dishwasher are required, but only to let the water fill and drain hose and power supply cable pass through. The dishwasher incorporates adjustable feet to allow the adjustment of the height. During all operations that involve accessibility to internal components the dishwasher has to be unplugged. Be sure that once the appliance has been installed, it is easily accessible for the service engineer in the event that a repair is required. Levelling Good levelling is essential for correct closure and sealing of the door. When the appliance is correctly levelled, the door will not catch on either side of the cabinet. If the door does not close correctly, loosen or tighten the adjustable feet until the machine is perfectly level. (See enclosed template). 25 26 27 www.electrolux.com 156991571-00-042008 ">
Advertisement