IKEA | RENGÖRA | User manual | IKEA RENGÖRA User Manual

RENGÖRA
GB
ENGLISH
4
ENGLISH
4
Contents
Safety instructions
Product description
Control panel
Programmes
Options
Before first use
Daily use
4
6
6
6
7
8
10
Hints and tips
Care and cleaning
Troubleshooting
Technical information
Environment concerns
IKEA GUARANTEE
12
13
14
16
17
17
Subject to change without notice.
Safety instructions
Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if
an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
Only a qualified service engineer can repair
this appliance. Use only original spare
parts.
To prevent injury and damage to the appliance, do not try to repair the appliance. Always contact the After Sales Service.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or
permanent disability.
• Do not let persons, children included, with
reduced physical sensory, reduced mental functions or lack of experience and
knowledge use the appliance. They must
have supervision or instruction for the operation of the appliance by a person who
is responsible for their safety. Do not let
children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the
appliance door when it is open.
Installation
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the appliance is installed
below and adjacent to safe structures.
Water connection
• Make sure not to cause damage to the
water hoses.
• Before you connect the appliance to new
pipes or pipes not used for a long time,
let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
• The water inlet hose has a safety valve
that prevents the hose to loosen. To disconnect the hose, press the lever (B) and
turn the fastener (A) clockwise.
A
B
• The water inlet hose has an external
transparent sheath. If the hose is damaged, the water in the hose becomes
dark.
• If the water inlet hose is damaged, immediately disconnect the mains plug from
the mains socket. Contact the service to
replace the water inlet hose.
ENGLISH
Electrical connection
Warning! Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the power
supply. If not, contact an electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Contact the service or an electrician to
change a damaged mains cable.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
• Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug,
use a 13 amp ASTA (BS 1362) fuse.
•
This appliance complies with the E.E.C.
Directives.
Use
• This appliance is intended to be used in
household and similar applications such
as:
– Staff kitchen areas in shops, offices and
other working environments
– Farm houses
– By clients in hotels, motels and other
residential type environments
– Bed and breakfast type environments.
5
Warning! Risk of injury.
• Do not change the specification of this
appliance.
• Put knives and cutlery with sharp points in
the cutlery basket with the points down or
in a horizontal position.
• Do not keep the appliance door open
without supervision to prevent to fall on it.
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous.
Obey the safety instructions on the detergent packaging.
• Do not drink and play with the water in
the appliance.
• Do not remove the dishes from the appliance until the programme is completed.
There can be detergent on the dishes.
Warning! Risk of electrical shock, fire
or burns.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Do not use water spray and steam to
clean the appliance.
• The appliance can release hot steam if
you open the door while a programme
operates.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and dispose of it.
• Remove the door catch to prevent children and pets to get closed in the appliance.
ENGLISH
6
Product description
8
7
1
6
2
5
1
2
3
4
5
6
7
8
Lower spray arm
Filters
Rating plate
Rinse aid dispenser
Detergent dispenser
Salt container
Upper spray arm
Upper basket
3
4
Control panel
1
2
1 On/off button
2 Programme buttons
Indicators
3
4
3 Delay button
4 Indicators
Description
Salt indicator. This indicator is off while the programme operates.
Rinse aid indicator. This indicator is off while the programme operates.
End indicator.
Programmes
Programme Degree of soil
1)
Type of load
Programme
phases
Duration
(min)
Energy
(kWh)
Water
(l)
Heavy soil
Crockery, cutlery, pots and
pans
Prewash
Wash 70 °C
Rinses
Dry
130 - 150
1.3 - 1.4
13 - 15
2)
ENGLISH
7
Programme Degree of soil
1)
Type of load
3)
4)
5)
Programme
phases
Duration
(min)
Energy
(kWh)
Water
(l)
Normal soil
Crockery and
cutlery
Prewash
Wash 65 °C
Rinses
Dry
100 - 110
1.2 - 1.6
15 - 16
Fresh soil
Crockery and
cutlery
Wash 60 °C
Rinse
30
0.8
9
Normal soil
Crockery and
cutlery
Prewash
Wash 50 °C
Rinses
Dry
195
1.03
12
All
Prewash
14
0.1
4
1) The pressure and the temperature of the water , the variations of the mains supply, the options and the quantity of
dishes can change the values.
2) This program is indicated for heavy soil loading to get the sufficient cleaning results on the pots and pans.
3) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
4) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with
normal soil. (This is the standard programme for test institutes).
5) Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and bad
odours to come out from the appliance.
Do not use detergent with this programme.
Information for test institutes
For all the necessary information for test performance. send an email to:
info.test@dishwasher-production.com
Write down the product number (PNC) that is on the rating plate.
Options
Acoustic signals
The acoustic signals operate when the appliance has a malfunction. It is not possible
to deactivate this acoustic signal.
There is also an acoustic signal that operates when the programme is completed. By
default, this acoustic signal is on, but it is
possible to deactivate it.
How to deactivate the acoustic signal for
the end of programme
1. Press the on/off button to activate the
appliance. Make sure that the appliance is in setting mode, refer to “Setting
and starting a programme”.
2.
Press and hold, at the same time,
and
3.
4.
until the indicators of
and
,
start to flash.
.
Press
•
and
go off.
The indicators of
•
continues to
The indicator of
flash.
• The end indicator is on.
. The end indicator goes off.
Press
The acoustic signal for the end of programme is deactivated.
ENGLISH
8
5. Press the on/off button to deactivate the
appliance and to confirm the setting.
How to activate the acoustic signal for the
end of programme
1. Refer to “How to activate the acoustic
signal for the end of programme” and
follow the procedure from step (1) to
step (2).
2.
.
Press
•
and
go off.
The indicators of
•
continues to
The indicator of
flash.
• The end indicator is off.
3.
. The end indicator comes on.
Press
The acoustic signal for the end of programme is activated.
4. Press the on/off button to deactivate the
appliance and to confirm the setting.
Before first use
1. Make sure that the set level of the water
softener agrees with the water hardness
in your area. If not, adjust the water
softener. Contact your local water authority to know the water hardness in
your area.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Processing residues can stay in the appliance. Start a programme to remove
them. Do not use detergent and do not
load the baskets.
Adjusting the water softener
Water softener
adjustment
Water hardness
German
degrees
(°dH)
French
degrees
(°fH)
mmol/l
Clarke
degrees
Level
47 - 50
84 - 90
8.4. - 9.0
58 - 63
10
43 - 46
76 - 83
7.6 - 8.3
53 - 57
9
37 - 42
65 - 75
6.5 - 7.5
46 - 52
8
29 - 36
51 - 64
5.1 - 6.4
36 - 45
7
23 - 28
40 - 50
4.0 - 5.0
28 - 35
6
19 - 22
33 - 39
3.3 - 3.9
23 - 27
5 1)
15 - 18
26 - 32
2.6 - 3.2
18 - 22
4
11 - 14
19 - 25
1.9 - 2.5
13 - 17
3
4 - 10
7 - 18
0.7 - 1.8
5 - 12
2
<4
<7
< 0.7
<5
12)
1) Default setting.
2) Do not use salt at this level.
ENGLISH
9
How to adjust the level of the water
softener
1. Press the on/off button to activate the
appliance. Make sure that the appliance is in setting mode, refer to “Setting
and starting a programme”.
2.
Press and hold, at the same time,
and
3.
4.
until the indicators of
and
4
Put 1 litre of water
in the salt container
(only for the first
time).
Put 1 kg of salt in
the salt container.
5
6
,
start to flash.
.
Press
•
and
go off.
The indicators of
•
continues to flash.
The indicator of
– The number of flashes of the end indicator show the level of the water
softener.
E.g. 5 flashes + pause + 5 flashes =
level 5.
again and again to
Press button
change the setting.
5. Press the on/off button to deactivate the
appliance and to confirm the setting.
Filling the salt container
Caution! Water and salt can come out
from the salt container when you fill it.
Risk of corrosion. To prevent this, after the
replenishment, start a programme.
1
3
Filling the rinse aid dispenser
1
2
3
4
2
M
+
AX
-
ENGLISH
10
rinse aid, turn the
selector between
position 1 (lowest
quantity) and position 4 (highest
quantity). Refer to
‘TROUBLESHOOTING’.
5
To adjust the released quantity of
Daily use
1. Open the water tap.
2. Press the on/off button to activate the
appliance. Make sure that the appliance is in setting mode, refer to “Setting
and starting a programme”.
• If the salt indicator is on, fill the salt
container.
• If the rinse aid indicator is on, fill the
rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for
the type of load and the degree of soil.
Using the detergent
1
2
3
A
A
Put the detergent or the tablet in the compartment (A).
4
5
B
If the programme
has a prewash
phase, put a small
quantity of detergent in compartment (B).
Using the combi detergent tablets
When you use tablets, that contain salt and
rinse aid, do not fill the salt container and
the rinse aid dispenser. The rinse aid indicator always comes on if the rinse aid dispenser is empty.
ENGLISH
1. Adjust the water softener to the lowest
level.
2. Set the rinse aid dispenser to the lowest
position.
If you stop to use the combi detergent
tablets, before you start to use separately
detergent, rinse aid and dishwasher salt,
do these steps:
1. Press the on/off button to activate the
appliance.
2. Set the water softener to the highest level.
3. Make sure that the salt container and
the rinse aid dispenser are full.
4. Start the shortest programme with a
rinsing phase, without detergent and
without dishes.
5. Adjust the water softener to the water
hardness in your area.
6. Adjust the released quantity of rinse aid.
Setting and starting a programme
The Auto Off function
To decrease the energy consumption, this
function automatically deactivates the appliance a few minutes after:
• You have not closed the door to start the
programme.
• The programme is completed.
Setting mode
For some settings it is necessary that the
appliance is in setting mode.
The appliance is in setting mode when, afis
ter the activation, the indicator of
on.
If the control panel does not show this condition, press and hold, at the same time
and
until the indicator of
comes on.
Starting a programme without delay start
1. Open the water tap.
2. Press the on/off button to activate the
appliance. The indicator of the
programme comes on.
3. Set a programme.
• If you want to start the
programme, close the appliance door.
11
• If you want to set a different programme, press the button of the programme you want to set. The related
programme indicator comes on.
4. Close the appliance door. The programme starts.
Starting a programme with delay start
1. Set the programme.
2. Press the delay button again and again
until the indicator of the number of hours
you want to set comes on (3, 6 or 9).
• The delay indicator comes on.
3. Close the appliance door. The countdown starts.
• When the countdown is completed, the
programme starts.
Opening the door while the appliance
operates
If you open the door, the appliance stops.
When you close the door, the appliance
continues from the point of interruption.
Cancelling the delay start while the
countdown operates
When you cancel the delay start you have
to set the programme and options again.
1.
Press and hold, at the same time,
and
until the
indicator
comes on.
Cancelling the programme
1.
Press and hold, at the same time,
and
until the indicator of
comes on.
Make sure that there is detergent in
the detergent dispenser before you
start a new programme.
At the end of the programme
When the programme is completed, the
end indicator is on.
1. Press the on/off button or wait for the
Auto Off function to automatically deactivate the appliance.
2. Close the water tap.
ENGLISH
Important
• Let the dishes become cold before you
remove them from the appliance. Hot
dishes can be easily damaged.
• First remove the items from the lower
basket, then from the upper basket.
12
• There can be water on the sides and on
the door of the appliance. Stainless steel
becomes cool more quickly than the
dishes.
Hints and tips
The water softener
Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water
softener neutralises these minerals.
The dishwasher salt keeps the water softener clean and in good conditions. It is important to set the right level of the water softener. This makes sure that the water softener uses the correct quantity of dishwasher
salt and water.
Loading the baskets
Refer to the supplied leaflet with examples of the load of the baskets.
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made
of wood, horn, aluminium, pewter and
copper.
• Do not put in the appliance items that
can absorb water (sponges, household
cloths).
• Remove remaining food from the items.
• To remove easily remaining burned food,
soak pots and pans in water before you
put them in the appliance.
• Put hollow items (cups, glasses and pans)
with the opening down.
• Make sure that cutlery and dishes do not
bond together. Mix spoons with other
cutlery.
• Make sure that glasses do not touch other glasses.
• Put the small items in the cutlery basket.
• Put the light items in the upper basket.
Make sure that they do not move.
• Make sure that the spray arms can move
freely before you start a programme.
Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause
damage to the appliance.
• The rinse aid helps, during the last rinsing
phase, to dry the dishes without streaks
and stains.
• Combi detergent tablets contain detergent, rinse aid and other added agents.
Be sure that these tablets are applicable
to the water hardness in your area. Refer
to the instructions on the packaging of the
products.
• Detergent tablets do not fully dissolve
with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with
long programmes.
• Do not use more than the correct quantity
of detergent. Refer to the instructions on
the detergent packaging.
Before starting a programme
Make sure that:
• The filters are clean and correctly installed.
• The spray arms are not clogged.
• The position of the items in the baskets is
correct.
• The programme is applicable for the type
of load and for the degree of soil.
• The correct quantity of detergent is used.
• There is dishwasher salt and rinse aid
(unless you use combi detergent tablets).
• The cap of the salt container is tight.
ENGLISH
13
Care and cleaning
Warning! Before maintenance,
deactivate the appliance and
disconnect the mains plug from the mains
socket.
5
6
D
Dirty filters and clogged spray arms
decrease the washing results.
Make a check regularly and, if necessary,
clean them.
Cleaning the filters
1
2
C
B
Remove filter (A).
Wash the filter with
water.
Put filter (A) to its
initial position.
Make sure that it
assembles correctly
under the two
guides (D).
7
8
A
3
4
To remove filters (B)
and (C), turn the
handle counterclockwise and remove. Pull apart filter (B) and (C).
Wash the filters with
water.
Assemble filters (B)
and (C). Put them
into position in filter
(A). Turn the handle
clockwise until it
locks.
An incorrect position of the filters can
cause bad washing results and damage to the appliance.
ENGLISH
14
Cleaning the filter of inlet hose
1
2
A
B
Cleaning the spray arms
Do not remove the spray arms.
If the holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.
External cleaning
Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads
or solvents.
Close the water tap. Disconnect the
hose. Press the lever
B and turn the fastener A clockwise.
3
4
Clean the filter of
inlet hose.
Troubleshooting
The appliance does not start or it stops during operation.
Before you contact the Service, refer to the
information that follows for a solution to the
problem.
With some problems, different indicators
flash continuously or intermittently at the
same time to show an alarm code.
ENGLISH
15
Alarm code
Problem
• The indicator of the set programme flash- The appliance does not fill with water.
es continuously.
• The end indicator flashes 1 time intermittently.
• The indicator of the set programme flash- The appliance does not drain the water.
es continuously.
• The end indicator flashes 2 times intermittently.
• The indicator of the set programme flash- The anti-flood device is on.
es continuously.
• The end indicator flashes 3 times intermittently.
Warning! Deactivate the appliance
before you do the checks.
Problem
Possible cause
Possible solution
The programme does
not start.
The mains plug is not connected in the mains socket.
Connect the mains plug.
The appliance door is open.
Close the appliance door.
The fuse in the fuse box is
damaged.
Replace the fuse.
The delay start is set.
Cancel the delay start or wait
for the end of the countdown.
The water tap is closed.
Open the water tap.
The water pressure is too low.
Contact your local water authority.
The water tap is clogged or
there is limescale on it.
Clean the water tap.
The appliance does
not fill with water.
The filter in the water inlet hose Clean the filter.
is clogged.
The appliance does
not drain the water.
The water inlet hose has a kink
or a bend.
Make sure that the position of
the hose is correct.
The anti-flood device is on.
There are water leakages in
the appliance.
Close the water tap and contact the service.
The sink spigot is clogged.
Clean the sink spigot.
The water drain hose has a
kink or a bend.
Make sure that the position of
the hose is correct.
ENGLISH
16
Problem
Possible cause
The salt indicator continues to stay on after
the replenishment of
the salt container.
This can occur when you are
If after 3 or 4 programmes, the
using salt that needs more time salt indicator continues to stay
to dissolve.
on, contact the service.
There is no unwanted effect on
the performance of the appliance.
After the checks are completed, activate the
appliance. The programme continues from
the point of interruption.
If the problem occurs again, contact the
service.
If the display shows other alarm codes, contact the service.
If the washing and drying results are not
satisfactory
Whitish streaks or bluish layers on glasses
and dishes
• The released quantity of rinse aid is too
much. Adjust the rinse aid selector to a
lower position.
• The quantity of detergent is too much.
Possible solution
• The quality of the detergent can be the
cause.
Dishes are wet
• The programme is without a drying
phase or with a low temperature drying
phase.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the
cause.
Refer to ‘HINTS AND TIPS’ for other
possible causes.
Stains and dry water drops on glasses
and dishes
• The released quantity of rinse aid is not
sufficient. Adjust the rinse aid selector to
a higher position.
Technical information
Dimensions
Width / Height / Depth (mm)
Electrical connection
Refer to the rating plate.
Voltage
Frequency
596 / 818 - 898 / 555
220-240 V
50 Hz
Water supply pressure
Min. / max. (bar / MPa)
Water supply 1)
Cold water or hot water2)
Capacity
Place settings
12
Left-on mode
0.99 W
Off-mode
0.10 W
Power consumption
(0.5 / 0.05 ) / (8 / 0.8 )
max. 60 °C
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot water
supply to decrease energy consumption.
ENGLISH
17
Environment concerns
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it.
Help protect the environment and human
health and to recycle waste of electrical
and electronic appliances. Do not dispose
appliances marked with the symbol with
the household waste. Return the product to
your local recycling facility or contact your
municipal office.
• Discard correctly the packaging material.
.
Recycle the materials with the symbol
IKEA GUARANTEE
How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years
from the original date of purchase of Your
appliance at IKEA, unless the appliance is
named LAGAN in which case two (2) years
of guarantee apply. The original sales receipt is required as proof of purchase. If
service work is carried out under guarantee,
this will not extend the guarantee period for
the appliance,
Which appliances are not covered by the
IKEA five (5) years guarantee?
The range of appliances named LAGAN
and all appliances purchased in IKEA before 1st of August 2007
Who will execute the service?
IKEA service provider will provide the service through its own service operations or
authorized service partner network.
What does this guarantee cover?
The guarantee covers faults of the appliance, which have been caused by faulty
construction or material faults from the date
of purchase from IKEA. This guarantee applies to domestic use only. The exceptions
are specified under the headline “What is
not covered under this guarantee?” Within
the guarantee period, the costs to remedy
the fault e.g. repairs, parts, labour and travel will be covered, provided that the appliance is accessible for repair without special
expenditure. On these conditions the EU
guidelines (Nr. 99/44/EG) and the respective local regulations are applicable. Replaced parts become the property of IKEA.
What will IKEA do to correct the problem?
IKEA appointed service provider will examine the product and decide, at its sole discretion, if it is covered under this guarantee.
If considered covered, IKEA service provider
or its authorized service partner through its
own service operations, will then, at its sole
discretion, either repair the defective product or replace it with the same or a comparable product.
What is not covered under this
guarantee?
• Normal wear and tear.
• Deliberate or negligent damage, damage caused by failure to observe operating instructions, incorrect installation or by
connection to the wrong voltage, damage caused by chemical or electro-chemical reaction, rust, corrosion or water
damage including but not limited to damage caused by excessive lime in the water supply, damage caused by abnormal
environmental conditions.
• Consumable parts including batteries
and lamps.
• Non-functional and decorative parts
which do not affect normal use of the appliance, including any scratches and possible color differences.
• Accidental damage caused by foreign
objects or substances and cleaning or unblocking of filters, drainage systems or
soap drawers.
ENGLISH
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery
baskets, feed and drainage pipes, seals,
lamps and lamp covers, screens, knobs,
casings and parts of casings. Unless such
damages can be proved to have been
caused by production faults.
• Cases where no fault could be found during a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where nonoriginal parts have been used.
• Repairs caused by installation which is
faulty or not according to specification.
• The use of the appliance in a non-domestic environment i.e. professional use.
• Transportation damages. If a customer
transports the product to their home or
other address, IKEA is not liable for any
damage that may occur during transport.
However, if IKEA delivers the product to
the customer's delivery address, then
damage to the product that occurs during
this delivery will be covered by this guarantee.
• Cost for carrying out the initial installation
of the IKEA appliance. However, if an
IKEA service provider or its authorized
service partner repairs or replaces the
appliance under the terms of this guarantee, the service provider or its authorized
service partner will re-install the repaired
appliance or install the replacement, if
necessary.
This restriction do not apply to fault-free
work carried out by a qualified specialist
using our original parts in order to adapt
the appliance to the technical safety specifications of another EU country.
How country law applies
The IKEA guarantee gives You specific legal
rights, which covers or exceed local demands. However these conditions do not
limit in any way consumer rights described
in the local legislation
18
Area of validity
For appliances which are purchased in one
EU country and taken to another EU country, the services will be provided in the
framework of the guarantee conditions normal in the new country. An obligation to
carry out services in the framework of the
guarantee exists only if the appliance complies and is installed in accordance with:
• the technical specifications of the country
in which the guarantee claim is made;
• the Assembly Instructions and User Manual Safety Information;
The dedicated After Sales Service for
IKEA appliances:
Please do not hesitate to contact IKEA After
Sales Service to:
1. make a service request under this guarantee;
2. ask for clarification on installation of the
IKEA appliance in the dedicated IKEA
kitchen furniture. The service won’t provide clarifications related to:
– the overall IKEA kitchen installation;
– connections to electricity (if machine
comes without plug and cable), to
water and to gas since they have to
be executed by an authorized service engineer.
3. ask for clarification on user manual contents and specifications of the IKEA appliance.
To ensure that we provide you with the best
assistance, please read carefully the Assembly Instructions and/or the User Manual
section of this booklet before contacting us.
How to reach us if You need our service
Please refer to the last page of this manual
for the full list of IKEA appointed contacts
and relative national phone numbers.
ENGLISH
Important! In order to provide You with a
quicker service, we recommend that You
use the specific phone numbers listed at the
end of this manual. Always refer to the
numbers listed in the booklet of the specific
appliance You need an assistance for.
Before calling us, assure that You have to
hand the IKEA article number (8 digit code)
for the appliance of which you need our
assistance.
Important! SAVE THE SALES RECEIPT! It is
Your proof of purchase and required for the
19
guarantee to apply. Note that the receipt
reports also the IKEA article name and
number (8 digit code) for each of the
appliances you have purchased.
Do You need extra help?
For any additional questions not related to
After Sales of your appliances, please contact our nearest IKEA store call centre. We
recommend you read the appliance documentation carefully before contacting us.
20
Country
België
Belgique
Phone number
070 246016
Call Fee
Opening time
Binnenlandse gesprekskosten
8 tot 20 Weekdagen
Tarif des appels nationaux
8 à 20. En semaine
България
00359 888 16 0 8
Такса за повикване от страната
От 9 до 18 ч в работни дни
Česká republika
246 019721
Cena za místní hovor
Danmark
70 15 09 09
Landstakst
8 až 20 v pracovních dnech
man.-fre. 09.00-20.00
lør. 09.00-16.00
1 søndag pr. måned, normalt første
søndag i måneden
Deutschland
+49 1806 33 45 32*
* 0,20 € / Verbindung aus dem Festnetz
max. 0,60 € / Verbindung aus dem
Mobilfunknetz
8 bis 20 Werktage
Ελλάδα
211 176 8276
Υπεραστική κλήση
8 έως 20 κατά τις εργάσιμες ημέρες
España
91 1875537
Tarifa de llamadas nacionales
De 8 a 20 en días laborables
France
0170 36 02 05
Tarif des appels nationaux
9 à 21. En semaine
Ireland
0 14845915
National call rate
8 till 20 Weekdays
Ísland
5880503
Innanlandsgjald fyrir síma
9 til 18. Virka daga
Italia
02 00620818
Tariffa applicata
alle chiamate nazionali
dalle 8 alle 20 nei giorni feriali
Κυπρος
22 030 529
Υπεραστική κλήση
8 έως 20 κατά τις εργάσιμες ημέρες
Lietuva
5 230 06 99
Nacionalinių pokalbių tarifai
Pr. - Ketv.: 8:00 - 12:00, 12:45 - 17:00
Pnkt.: 8:00 - 12:00, 12:45 - 15:45
Magyarország
061 998 0549
Belföldi díjszabás
Hétköznap 8 és 10 óra között
Nederland
0900 235 45 32
and/or
0900 BEL IKEA
15 cent/min., starttarief 4.54 cent
en gebruikelijke belkosten
ma-vr 08.00-20.00,
zat 09.00-20.00
(zondag gesloten)
Norge
815 22052
Takst innland
8 til 20 ukedager
Österreich
0810 300486
max. 10 Cent / min.
Mo-Fr 8.00 - 20.00 Uhr
Polska
012 297 8787
Stawka wg taryfy krajowej
Od 8 do 20 w dni robocze
Portugal
211557985
Chamada Nacional
9 às 21. Dias de Semana
*excepto feriados
România
021 211 08 88
Tarif apel naţional
8 - 20 în zilele lucrătoare
Россия
8 495 6662929
Действующие телефонные тарифы
с 8 до 20 по рабочим дням
Время московское
Tarif für Anrufe im Bundesgebiet
8 bis 20 Werktage
Tarif des appels nationaux
8 à 20. En semaine
Tariffa applicata
alle chiamate nazionali
dalle 8 alle 20 nei giorni feriali
(02) 3300 2554
Cena vnútroštátneho hovoru
8 až 20 v pracovných dňoch
Suomi
030 6005203
Lankapuhelinverkosta
0,0835€/puhelu+0,032€/min
Matkapuhelinverkosta 0,192€/min
arkipäivisin 8.00-20.00
Sverige
0775 700 500
lokalsamtal (lokal taxa)
mån-fre 8.30-20.00
lör-sön 9.30-18.00
Schweiz
Suisse
031 5500 324
Svizzera
Slovensko
Türkiye
212 244 0769
Ulusal arama ücreti
Hafta içi saat 09:00’dan 18:00’a kadar
Україна
044 586 2078
Міжміськи дзвінки платні
9 - 21 В робочі дні
United Kingdom
020 3347 0044
National call rate
9 till 21. Weekdays
Slovenija
www.ikea.com
Hrvatska
www.ikea.com
Србија
www.ikea.com
21
22
23
156966370-A-412013
© Inter IKEA Systems B.V. 2008
AA-970221-1
Download PDF

advertising