JOHN LEWIS JLBIWD1405 User Manual

Washer Dryer
JLBIWD1405
User Manual
Contents
Safety information
4
Children and vulnerable people safety
4
General Safety
5
Safety instructions
8
Installation
8
Electrical Connection
8
Water Connection
8
Use
8
Service
9
Disposal
9
Installation
10
Be prepared for installation
10
The appliance is equipped with ...
10
Unpacking
10
Installation on suspended flooring
12
Positioning and levelling
13
Hose and cable connection
13
Building in
16
Installing anti-tilting device (Accessory)
17
Preparation and assembly of the cupboard door
18
Product description
21
Appliance overview
21
Control panel
22
Control panel description
22
Display
23
Dial and buttons
25
Introduction
25
On/Off
25
25
Mode
Temp
25
Spin
25
Prewash
26
26
Permanent Extra Rinse
26
Reduce time
Child Lock
26
Time dry
27
2
Auto dry
Delay start
Start/Pause
Programmes
Programme Chart
Automatic drying
Timed drying
Settings
Acoustic signals
Before first use
Daily Use - Washing only
Activating the appliance
Loading the laundry
Filling the detergent and additives
Check the position of the detergent flap
Setting a programme
Starting a programme
Starting a programme with the delay start
The SensiCare System load detection
Interrupting a programme and changing the
options
Cancelling a running programme
Opening the door - Adding garments
End of the programme
Draining water out after end of cycle
Stand-by function
Daily use - Washing & Drying
Complete wash&dry programme
Washing and Drying - Automatic levels
Washing and Timed Drying
At the end of the drying programme
Daily use - Drying only
Preparation to drying
Drying - Automatic levels
Timed Drying
At the end of the drying programme
Fluff in the fabrics
27
27
27
28
28
33
34
36
36
37
38
38
38
38
39
39
39
40
40
40
41
41
41
41
42
43
43
43
44
44
45
45
45
45
45
47
Washer Dryer User Manual
Hints and tips
The laundry load
Stubborn stains
Detergents and other treatments
Ecological hints
Water hardness
Prepare the drying cycle
Items not suitable for drying
Garment labels
Drying cycle duration
Additional drying
General Tips
Care and cleaning
External cleaning
Descaling
Maintenance wash
48
48
48
48
49
49
49
49
49
49
49
49
51
51
51
51
Door seal with double lip trap
Cleaning the drum
Cleaning the detergent dispenser
Cleaning the drain pump
Cleaning the inlet hose and the valve filter
Emergency drain
Frost precautions
Troubleshooting
Introduction
Possible failures
Emergency door opening
Consumption values
Technical Data
Repairs - after sales service
51
51
52
53
56
56
56
57
57
58
60
61
62
63
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible location
for future reference.
Children and vulnerable people safety
Warning!
Risk of suffocation, injury or permanent disability.
This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
• Children of less than 3 years of age should be kept away from the
appliance unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the door is
open.
• Children shall not carry out cleaning and user maintenance of the
appliance without supervision.
•
4
Washer Dryer User Manual
General Safety
Do not change the specification of this appliance.
• This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
– by clients in hotels, motels, bed & breakfast and other residential
type environments;
– areas for communal use in blocks of flats or in launderettes.
• The appliance shall be installed as a freestanding product or below
the kitchen worktop if space margins permit.
• Do not install the appliance behind a lockable door, a sliding door
or a door with a hinge on the opposite side, that would prevent the
appliance door from being fully open.
• Connect the mains plug to the mains socket only at the end of the
installation process. Make sure that the mains plug is accessible after
installation.
• The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
• WARNING: The appliance must not be supplied through an
external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by a utility.
• Ensure good air ventilation in the room where the appliance is
installed to avoid the backflow of unwanted gases into the room
from appliances burning gas or other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for
exhausting fumes from any appliances burning gas or other fuels.
• The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar
(0.8 MPa).
• Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
•
Washer Dryer User Manual
5
The appliance must be connected to the water mains using the new
supplied hose sets, or other new hose sets supplied by the
Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be replaced by
the manufacturer, its Authorised Service Centre or similarly
qualified persons to avoid an electrical hazard.
• Wipe away lint or packaging debris that has accumulated around
the appliance.
• Items that have been soiled with substances such as vegetable or
mineral oil, acetone, alcohol, petrol, kerosene, spot removers,
turpentine, waxes and wax removers should be washed separately
with an extra amount of detergent before being dried in the washer
dryer.
• Do not use the appliance if items have been soiled with industrial
chemicals.
• Do not dry unwashed items in the wash dryer.
• Items such as foam rubber (latex foam), shower caps, waterproof
textiles, and rubber backed articles and clothes, or pillows fitted
with foam rubber pads should not be dried in the washer dryer.
• Fabric softeners, or similar products, should only be used as
specified by the product manufacturer’s instructions.
• Remove all objects from items that could be a source of fire ignition
such as lighters or matches.
• Never stop the washer dryer before the end of the drying cycle
unless all items are quickly removed and separated so that residual
heat can dissipate.
• The final part of the washer dryer cycle takes place without heat
(cool down cycle) to ensure that items reach a temperature that
will not cause damage to them.
• Do not use high pressure water sprays and/or steam to clean the
appliance.
• Clean the appliance with a moist cloth. Use only neutral detergents.
Do not use abrasive products, abrasive cleaning pads, solvents or
metal objects.
•
6
Washer Dryer User Manual
•
Before any maintenance operation, deactivate the appliance and
disconnect the mains plug from the socket.
Washer Dryer User Manual
7
Safety instructions
Installation
The installation must comply with
relevant national regulations.
• Follow the installation instructions supplied with
the appliance.
• Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
• Always keep the appliance vertical when it is
being moved.
• Make sure that there is air circulation between
the appliance and the floor.
• Remove all the packaging and the transit bolts.
• The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
• Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they
must be reattached to lock the drum to prevent
an internal damage.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use a damaged appliance.
• Do not install the appliance where the appliance
door cannot be fully opened.
• Adjust the feet to have the necessary space
between the appliance and the flooring.
• When the appliance is in its permanent
position, check if it is levelled correctly with the
aid of a spirit level. If it is not, adjust the feet
accordingly.
Electrical Connection
Warning! Risk of fire and
electric shock.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains plug
with wet hands.
• UK and Ireland only. This appliance is fitted with
a 13 A mains plug. If it is necessary to change
the mains plug fuse, use only a 13 A ASTA (BS
1362) fuse.
• This appliance complies with the E.E.C.
Directives.
Water Connection
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water
meters, etc.), let the water flow until it is clean
and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
Use
Warning! Risk of injury,
electric shock, fire, burns or
damage to the appliance.
• Do not put flammable products or items that
are wet with flammable products in, near or on
the appliance.
• Do not touch the glass door while a
programme is in operation. The glass can get
hot.
• Do not dry damaged (torn, frayed) items that
contain padding or fillings.
• The appliance must be earthed.
8
Washer Dryer User Manual
• If laundry has been washed with a stain
remover, carry out an additional rinse cycle
before starting a drying cycle.
• Make sure that all metal objects are removed
from the laundry.
• Only dry fabrics that are suitable to dry in the
washer dryer. Follow the cleaning instruction
on the item label.
• Plastic items are not heat resistant.
– If a detergent ball is used, remove it before
starting a drying programme.
– Do not use a detergent ball if setting a nonstop programme.
Warning! Risk of injury or
damage to the appliance.
• Do not sit or stand on the open door.
• Do not dry dripping wet clothes in the
appliance.
Service
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
Disposal
• Disconnect the appliance from the mains
electrical and water supplies.
• Cut off the mains electrical cable close to the
appliance and dispose of it.
• Remove the door catch to prevent children or
pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
Washer Dryer User Manual
9
Installation
Warning! Refer to Safety
chapters.
Be prepared for installation
It is recommended that installation
is carried out by two persons.
The appliance is equipped
with ...
A
B
C
D
E
x4
x2
x1
x1
x1
F
G
H
L
x1
x2
x1
x1
x1
x2
Unpacking
Warning! Use the gloves.
Warning! Remove all the packaging and the transit bolts before installing
the appliance.
10
Washer Dryer User Manual
1. Put two polystyrene packaging elements on the
floor under the appliance.
Warning! It is strongly
recommended that this
action is carries out by two
persons.
2. Carefully put the appliance down on its rear side.
Make sure not to damage the
hoses.
3. Remove the polystyrene protection from the
bottom.
1
2
4. Return the appliance in vertical position and
remove the socket polystyrene protection.
1
2
5. Remove the power supply cable and the drain
hose from the hose holders.
It is possible to see water
flowing from the drain hose. This
is due to the testing with water
of the appliance in factory.
Washer Dryer User Manual
11
6. Remove the three bolts, the hose holders and
plastic spacers by using the spanner supplied with
the appliance.
F
7. Close the holes with the plastic caps you find in
the user manual bag. Put the smallest cap F in
upper hole and the two bigger caps G in lower
holes.
G
We recommend that you keep the packaging and the transit bolts for any movement of
the appliance.
Installation on suspended
flooring
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond
the front feet.
Suspended wooden floors are particularly
susceptible to vibration.
If possible, install the appliance where the floor
is more stable.
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
12
Washer Dryer User Manual
Positioning and levelling
1. Install the appliance on a flat hard floor.
Warning! Make sure that
carpets do not stop the air
circulation below the appliance.
Bring the appliance near the furniture
recess before levelling it. For more
details, refer to paragraph "Building
in".
2. Loosen or tighten the feet to adjust the level.
x4
A correct adjustment of the
appliance level prevents the vibration,
noise and the movement of the
appliance when in operation.
The appliance must be level and stable.
Caution! Do not put cardboard,
wood or equivalent materials
below the appliance feet to
adjust the level.
Hose and cable connection
900 mm
Washer Dryer User Manual
760 mm
1360 mm
max 1000 mm
max 1000 mm
min. 600 mm
1020 mm
1450 mm
min. 600 mm
1100 mm
13
The inlet hose
1. Remove the inlet hose from inside the drum.
2. To connect the water inlet hose towards the proper
direction and with the proper inclination, check the
position of the water tap before connecting it to the
back of the appliance.
Make sure the hose is nor kinked,
squashed but neither tensed.
45
20
O
3. Connect the hose to the back of the appliance. Do
not turn the inlet hose downwards, but turn it left or
right depending on the position of your water tap.
4. Loosen the ring nut to fix it in the correct position.
O
5. Connect the water inlet hose to the cold water tap
with 3/4 thread.
Warning! Make sure that there
are no leaks from the couplings.
Use the hose supplied with appliance.
Do not use an extension hose if the inlet hose is too short. Contact the Authorised
Service Centre for an inlet hose replacement.
14
Washer Dryer User Manual
Water drainage
The drain hose can be connected:
To a stand pipe with vent-hole
Directly into a drain pipe at a height of not less than 60
cm (23.6”) and not more than 100 cm (39.3”).
The end of the drain hose must always be ventilated , i.e.
the inner diameter of the drain pipe (min. 40 mm - min.
1.6”) must be larger than the external diameter of the
drain hose.
Ø 40 mm
max.600 mm
To a sink spigot
Put the drain hose in the spigot and tighten it with the
supplied cable tie L.
Make sure that the drain hose makes a loop to prevent
particles going into the appliance from the sink.
L
To a wall-pipe
Directly to a built-in drain pipe in the room wall and
tighten it with the supplied cable tie L.
You can extend the drain hose to maximum 400 cm. Contact the service centre for the
other drain hose and the extension.
Washer Dryer User Manual
15
Building in
This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions
shown in this picture.
min. 600 mm
For recess with a height different
than 820 mm, it is possible to buy the
appropriate kit on the website.
min.
560 mm
min.
820 mm
16-22 mm
596 mm
If hoses run behind the appliance,
make sure that nothing closes the
small recess indicated with the
measures 50 x 50 mm.
553 mm
819 mm
50 mm
50 mm
140 mm
76 mm
The appliance is also equipped with an adhesive sponge
pad H that you can find inside the drum.
Attach it on the top of the appliance where indicated in
the drawing.
When levelling the appliance under the furniture, DO
NOT squeeze the sponge pad.
16
Washer Dryer User Manual
Before proceeding with appliance building in, bring it
near the recess and preposition the inlet hose, the drain
hose and the mains cable.
Warning! Make sure they are
not kinked or squashed.
Installing anti-tilting device
(Accessory)
Install this accessory in case of risk of appliance tilting only.
If the height of the counter is 820 mm or lower, you cannot install the anti-tilting
device.
1. Remove the screws of the top cover on the rear of
the appliance and install the anti-tilting device as shown
in the drawing.
~10mm
Washer Dryer User Manual
2. Adjust the anti-tilting device so that the distance from
the counter is 10mm. Loosen the nut counterclockwise
with a 3mm wrench. Adjust the height and turn the nut
clockwise to fix it.
17
Preparation and assembly of the cupboard door
The dimensions of the cupboard door should be:
• width min. 595 - max. 598 mm;
• thickness 16-22 mm.
Factory pre setting
The appliance is originally pre set for the assembly of a
cupboard door opening from right to left.
The best solution would be to screw
the upper hinge to the upper hole of
the top plate and the lower hinge to
the lower hole of the bottom plate.
Reversibility of the cupboard door
Carry out the cupboard door reversibility before the
appliance is built in completely.
N
M
If the cupboard door has to be opened from left to
right, invert the position of the hinge supports M with
the magnetic plate N and lower plate O.
O
18
Washer Dryer User Manual
Make sure that the plate with
magnet is on the upper position.
M
N
O
Cupboard door preparation
For countersinking the door, it is
recommended to call a professional.
y
Align the cupboard door to the furniture correctly.
Measure the distance X to fix the height of the hole to
countersink the upper hinge. The centre of the hole Y
should be at the same height of the stroke on the hinge
support.
x
y
Set the position of the lower hole respecting dimensions
and distances shown in the drawing (449 mm).
Countersink the holes.
16-22 mm
Ø 35 mm
449
mm
12,5 - 14 mm
22±1,5 mm
595-598 mm
Hinges
To mount the hinges it is necessary to drill two holes
(dia. 35 mm, depth 12.5 - 14 mm depending on the
depth of cupboard door) on the inner side of the door.
The hinges will be fixed to the door by means of the
four supplied screws A.
A
Washer Dryer User Manual
19
To align the door perfectly, make
sure that the edge of cupboard door
is parallel with the appliance edge
and to respect the proper opening
angle (max. 105 °).
max. 105°
Mounting the door
Fix the hinges to the hinge supports on the appliance by
means of the two supplied screws B.
The hinges can be adjusted to
compensate for possible uneven
thickness of the door.
1
N
2
E
D
C
20
Counter-magnet
The appliance is pre set for a magnetic closure.
For a correct closure:
1. Position the screw C and the counter-magnet D on
the magnetic plate N. Lean the cupboard door
against the screw until it leaves a mark.
2. Open the cupboard door and screw the countermagnet D (steel disk + rubber ring E) with the
screw C in the inner side of the cupboard door,
where the screw left the mark as described in the
first step.
Washer Dryer User Manual
Product description
Appliance overview
1
2
10
3
11 12
4
5
6
7
8
9
13
1. Hinge supports
2. Detergent dispenser
3. Control panel
4. Magnetic plate
5. Door handle
6. Rating plate
7. Plate with rubber beater
8. Drain pump filter
9. Front feet for levelling the appliance
10. Drain hose
11. Mains cable
12. Inlet hose connection
13. Back feet for levelling the appliance
Washer Dryer User Manual
21
Control panel
Control panel description
1
1h wash & dry 1kg
2
Cotton
Cotton eco
Outdoor
Synthetics
40°
Sportswear
Delicates
30°
Anti-allergy
Rinse
60°
Wool
Steam refresh
Spin/Drain
Wash
20°
Dry
Cold
Mode
Temp.
12
The permanent options are set by
holding pressed the relative button
for at least 3 seconds.
1.
2.
3.
4.
5.
6.
7.
4
5
90°
Denim
Machine Clean
3
Programme dial
Display
Time dry touch button
Auto dry touch button
Start/Pause touch button
Delay start touch button
Reduce time touch button and permanent
Auto dry
Start/
Pause
Time dry
Spin
11 10 9
Prewash
8
Reduce
Time
7
Delay
Start
6
8. Prewash touch button and permanent Extra
Rinse option
9. Spin touch button
10. Temp touch button
11. Mode touch button:
• Mode - Wash
• Mode - Dry
12. On/Off push button
Child Lock option
22
Washer Dryer User Manual
Display
Door locked indicator.
The digital indicator can show:
•
Programme duration (e. g.
•
Delay time (e. g.
•
Cycle end (
•
Warning code (e.g.
•
Error indicator (
, washing and/or drying phase).
).
).
).
).
Reduce time indicator.
Extra Rinse indicator.
The spin area:
Spin speed indicator
No Spin indicator. Spin phase is off.
Rinse Hold indicator.
After the SensiCare System detection, it flashes when the laundry load exceeds the
maximum declared load of the selected programme. Refer to "The SensiCare System load detection " paragraph.
Auto dry indicator:
Iron dry
Cupboard dry
Extra dry
Child safety lock indicator.
Washer Dryer User Manual
23
Time dry and Non-Stop programme indicator.
24
Washer Dryer User Manual
Dial and buttons
Introduction
The options/functions are not
available with all washing
programmes. Check the
compatibility between options/
functions and washing programmes
in the "Programme Chart". An
option/function can exclude
another one, in this case the
appliance doesn't allow you to set
incompatible options/functions.
On/Off
Press this button for a few seconds to activate
or deactivate the appliance. Two different tunes
sound while switching the appliance on or off.
As the Stand-by function automatically
deactivates the appliance after several minutes
to reduce the energy consumption, you may
need to activate the appliance again.
For more details, refer to Stand-by paragraph in
Daily Use chapter.
Mode
Thanks to this button, a cycle can perform:
• Only washing: Mode - Wash indicator is on
(default mode).
• Washing and drying: Mode - Wash and
Mode - Dry indicators are on.
• Only drying: Mode - Dry indicator is on.
Temp
When you select a washing programme, the
appliance automatically proposes a default
temperature.
Washer Dryer User Manual
Tap on this button to change the water
temperature.
The indicator of the set temperature comes on.
The indicator Cold corresponds to cold water.
Spin
When you set a programme, the appliance
automatically sets the maximum spin speed
allowed, except for programme Denim. With
this option you can decrease the default spin
speed.
Touch repeatedly this button to:
• Decrease the spin speed. The display shows
only the spin speeds available for the set
programme.
• Additional spin options No Spin
.
Set this option to deactivate all spin phases. The
appliance performs the only draining phase of
the selected washing programme. Set this
option for very delicate fabrics. The rinses
phase uses more water for some washing
programmes
option.
• Activate the Rinse Hold
The final spin is not performed. The water of
the last rinse is not drained out to prevent the
fabrics from creasing. The washing programme
ends with water in the drum.
The indicator
is on display. The door stays
locked and the drum turns regularly to reduce
creasing. You must drain the water to unlock
the door.
If you touch the Start/Pause button, the
appliance performs the spinning phase and
drains the water.
The appliance empties the
water out automatically after 18
hours approximately.
25
• Use this option to add a pre-wash phase at 30
°C before the washing phase.
This option is recommended for heavily soiled
laundry, especially if containing sand, dust, mud
and other solid particles.
The options can increase the
programme duration.
very quick cycle for a smaller lightly soiled
load (max. half load recommended).
the shortest cycle to freshen up a small
amount of laundry.
The Reduce time is available only with the
programmes in the table.
indicator
Permanent Extra Rinse
1)
With this option you can permanently have an
extra rinse when you set a new programme.
To activate/deactivate this option, hold the
Prewash button pressed for 3 seconds until the
indicator
comes on/goes off on the
display.
When it is activated, the appliance will default to
this option after you switch it off or change/
reset the programme.
This option increases the
programme duration.
Reduce time
With this option you can reduce the programme
duration depending on the load size and the
degree of soiling.
When you set a washing programme, the display
shows the default duration and
dashes.
Synthetics
The corresponding indicator above the touch
button illuminates.
Cotton eco
With this option you can add a prewash phase
to a washing programme.
a quick cycle for a full load of lightly soiled
garments.
Cotton
Prewash
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
1) Default duration for all programmes.
Reduce time with steam programmes
When setting a steam programme, this button
allows to chose three steam levels and the
programme duration is reduced accordingly:
•
: maximum.
•
: medium.
•
: minimum.
Child Lock
Touch Reduce time button to reduce the
programme duration according to your needs.
The display shows the new programme duration
and a number of dashes will decrease
accordingly:
With this option you can prevent children from
playing with the control panel.
suitable for a full load of normally soiled
garments.
When it is activated, the appliance will default to
this option after you switch it off or change/
26
To activate/deactivate this option, hold the
Reduce time button pressed until the indicator
comes on/goes off on the display.
Washer Dryer User Manual
reset the programme. If you press any button,
the indicator
blinks to indicate that the
buttons are disabled.
Time dry
Touch this button to set the time that suits the
fabrics you have to dry (refer to "Timed drying"
table). The display shows the set value.
Each time you touch this button the time value
increases by 5 minutes.
You cannot set all time values for
different types of fabrics.
Auto dry
Touch this button to set one the automatic
dryness levels proposed by the appliance.
On the display the relevant dryness indicator
goes on:
•
Iron dry: laundry to be ironed.
•
Cupboard dry: laundry to be put in store.
•
Extra dry: laundry to be fully dried.
You can not set all automatic
levels for each type of fabrics.
Delay start
With this option you can delay the start of a
programme to a more convenient time.
Touch the button repeatedly to set the required
delay. The time increases in steps of 1 hour up
to 20 hours.
The corresponding indicator above the touch
button illuminates.
The display shows the selected delay time. After
touching the Start/Pause button, the appliance
begins the countdown and the door is locked.
Start/Pause
Touch the Start/Pause button to start, pause
the appliance or interrupt a running programme.
Washer Dryer User Manual
27
Programmes
Programme Chart
Programme
Reference
Default temperature spin speed
Temperature range Spin speed
range
Maximum
load
Programme description
(Type of load and soil level)
Washing programmes
Cotton
40 °C
90 °C - Cold
Cotton eco1)
40 °C
60 °C - 40 °C
Synthetics
40 °C
60 °C - Cold
Delicates
30 °C
40 °C - Cold
Wool
40 °C
40 °C - Cold
28
1600 rpm
(1600- 400
rpm)
7 kg
White cotton and coloured cotton. Normal, heavy
and light soil.
1600 rpm
(1600- 400
rpm)
7 kg
White cotton and fast-coloured cotton. Normal
soil. The energy consumption decreases and the time of
the washing programme is extended, ensuring good
washing results.
1200 rpm
(1200 - 400
rpm)
3 kg
Synthetic items or mixed fabric items. Normal soil.
1200 rpm
(1200- 400
rpm)
2 kg
Delicate fabrics such as acrylics, viscose and
mixed fabrics requiring gentler washing. Normal
soil.
1.5 kg
Machine washable wool, hand washable wool and
1200 rpm
(1200 - 400
rpm)
other fabrics with «hand washing» care symbol2).
Washer Dryer User Manual
Programme
Reference
Default temperature spin speed
Temperature range Spin speed
range
Maximum
load
Programme description
(Type of load and soil level)
Steam programme
Steam programme can be used for reducing wrinkles and odours3) of garments that just need to be refreshed,
avoiding washing. The fabric fibres are relaxed and afterwards ironing becomes effortless. When the programme is completed, quickly remove the laundry from the drum4). Steam programmes do not perform any
hygienic cycle. Do not set one of these programmes with the following type of items:
• Items that are not suitable for tumble drying.
• All items with plastic, metal, wooden parts or alike.
1 kg
Steam refresh
-
Cottons, Synthetics, Delicates. Short and gentle
steam programme to refresh even your very delicate garments, including very delicate garments with sequins, lace
etc. When treating smaller loads, the programme duration can be further reduced by means of the Reduce time
option.
Warning! Do not use this programme with wool and garments labelled as dry-clean only.
1600 rpm
(1600 - 400
rpm)
7 kg
Spin/Drain
All fabrics, except woollens and delicate fabrics.
To spin the laundry and to drain the water in the drum.
1600 rpm
(1600- 400
rpm)
7 kg
Rinse
All fabrics, except woollens and very delicate fabrics. Programme for rinsing and spinning the laundry. The
default spin speed is the one used for cotton programmes. Reduce the spin speed accordingly to the type
of laundry. If necessary, set the Extra Rinse option to add
rinses. With a low spin speed, the appliance performs delicate rinses and a short spin.
Washer Dryer User Manual
29
Programme
Reference
Default temperature spin speed
Temperature range Spin speed
range
Machine Clean
60 °C
Maximum
load
1200 rpm
(1200 - 400
rpm)
-
Programme description
(Type of load and soil level)
Maintenance cycle with hot water to clean and freshen
the drum and to remove residue that may cause odour.
For the best result use this cycle once a month. Before
running this cycle, remove all items from the drum. In the
washing phase compartment of the detergent dispenser,
put the flap of the compartment in upward position. Pour
a cup of chlorine bleach or a washing machine cleaner in
the washing phase compartment. DO NOT use both together.
After the drum cleaning, run a further
rinse cycle with empty drum and no
detergent to remove any residue of
bleach.
If you set this programme with the Mode - Dry, the appliance performs the anti-fluff action. Refer to chapter 'Fluff
in the fabrics'.
Anti-allergy
60 °C
Sportswear
30 °C
40 °C - Cold
30
1600 rpm
(1600 - 400
rpm)
7 kg
White cotton items. This programme removes microorganisms thanks to a washing phase with the temperature maintained above 60°C for several minutes. This
helps remove germs, bacteria, micro-organism and particles. An additional rinsing phase ensures a proper removal
of detergent residues and pollens/allergenic items. In this
way the wash is more effective.
1200 rpm
(1200- 400
rpm)
3 kg
Synthetic sport items. This programme is designed to
gently wash modern outdoor sportswear and is also suitable for gym, cycling or jogging clothes or similar.
Washer Dryer User Manual
Programme
Reference
Default temperature spin speed
Temperature range Spin speed
range
Outdoor
30 °C
40 °C - Cold
1200 rpm
(1200- 400
rpm)
Maximum
load
2 kg
Programme description
(Type of load and soil level)
Do not use fabric softener and make
sure that there is no softener residue
in the detergent dispenser.
Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a
removable fleece or inner insulation.
By performing a combined wash and
dry programme, the drying phase also
acts as water-repellent restorer.
Make sure that the garment
care label permits tumble drying.
Denim
30 °C
40 °C - Cold
1200 rpm
(1200 - 400
rpm)
3 kg
Special programme for Denim clothing with delicate washing phase to minimize colour fading
and marks. For better care a reduced load size is recommended.
1200 rpm
1 kg
Mixed fabrics (cotton and synthetic items). Complete short programme to wash and dry laundry loads up
to 1 kg in one go. It only lasts 1 hour.
1h wash & dry 1kg
30 °C
40 °C - 30 °C
Reset position. The display shows dashes only.
1) Cottons energy saving programme. This programme at 60ºC with a load of 7 kg is the reference programme for data
entered in the energy label, in compliance with 96/60/EC Directive. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or doesn't rotate
properly, but this is normal for this programme.
3) Steam programme doesn't remove particularly intense odour.
4) After the steam treatment the laundry can be humid. Hang items out for a few minutes.
Washer Dryer User Manual
31
Programme options compatibility
Delicates
Wool
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Prewash
Delay start
Synthetics
Reduce time
Cotton eco
No Spin
Cotton
Spin
Programme
■
■
■
Steam refresh
Spin/Drain
Rinse
Machine Clean
Anti-allergy
Sportswear
Outdoor
Denim
32
■
■
■
■1)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Washer Dryer User Manual
Delay start
Reduce time
Prewash
No Spin
Spin
Programme
■
1h wash & dry 1kg
1) If you set the No Spin option, the appliance performs draining only.
Automatic drying
Dryness Level
1)
Extra Dry
For towelling materials
1)
Cupboard Dry2)
For items to be stored
Washer Dryer User Manual
Type of fabric
Load
Cottons and Linen
(bathrobes, bath towels, etc)
up to 4 kg
Denim garments
up to 3 kg
Cottons and Linen
(bathrobes, bath towels, etc)
up to 4 kg
Synthetics and mixed fabrics
(jumpers, blouses, underwear,
household and bed linen)
up to 3 kg
Delicate fabrics
(acrylics, viscose and delicate mixed
fabrics)
up to 2 kg
Wool items
(woollen jumpers)
up to 1 kg
Outdoor sporting garments
(outdoor clothing, technical, sport
fabrics, waterproof and breathable
jackets, shell jackets)
up to 2 kg
Denim garments
up to 3 kg
Sportswear
up to 3 kg
33
Dryness Level
3)
Iron Dry
Suitable for ironing
Type of fabric
Load
Cottons and Linen
(sheets, tablecloths, shirts, etc)
up to 4 kg
1) Selectable in Cotton eco and Anti-allergy (if available) programme also.
2) Hints for test institute The test performance, in accordance with EN 50229, must be carried out with a FIRST drying load
of the maximum declared drying capacity (load composition according to EN61121) by setting the AUTOMATIC CUPBOARD
DRY for Cotton eco programme. The SECOND drying load with the residual load must be tested by setting the AUTOMATIC
CUPBOARD DRY for Cotton eco programme.
3) Selectable in Anti-allergy programme (if available) also.
Timed drying
Dryness Level
Type of fabric
Extra Dry
For towelling materials
Cottons and Linen
(bathrobes, bath towels, etc)
Cupboard Dry
For items to be
stored
34
Load
(kg)
Spin
speed
(rpm)
Suggested duration (mins)
4
1600
170 - 190
2
1600
110 - 120
1
1600
65 - 75
Denim garments
3
1200
155
Cottons and Linen
(bathrobes, bath towels, etc)
4
1600
160 - 180
2
1600
100 - 110
1
1600
55 - 65
Synthetics and mixed fabrics
(jumpers, blouses, underwear, household and
bed linen)
3
1200
135 - 150
1
1200
45 - 55
Delicates
(acrylics, viscose and delicate mixed fabrics)
2
1200
150
Wool
(woollen jumpers)
1
1200
80 - 100
Outdoor sporting garments
(outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets)
2
1200
160
Denim garments
3
1200
145
Sportswear
3
1200
140
Washer Dryer User Manual
Dryness Level
Type of fabric
Iron Dry
Suitable for ironing
Cottons and Linen
(sheets, tablecloths, shirts, etc)
Washer Dryer User Manual
Load
(kg)
Spin
speed
(rpm)
Suggested duration (mins)
4
1600
110 - 125
2
1600
65 - 75
1
1600
40 - 50
35
Settings
Acoustic signals
This appliance has different acoustic signals, that
operate when:
• You activate the appliance (special short tune).
• You deactivate the appliance (special short
tune).
• You touch the buttons (click sound).
• You make an invalid selection (3 short sounds).
• The programme is completed (sequence of
sounds for about 2 minutes).
• The appliance has a malfunction (sequence of
short sounds for about 5 minutes).
To activate/deactivate the acoustic signals
when the programme is completed, touch the
Mode and the Temp buttons simultaneously for
about 2 seconds. The display shows On or Off.
If you deactivate the acoustic
signals, they continue to operate
when the appliance has a
malfunction.
36
Washer Dryer User Manual
Before first use
1. Make sure that the electrical power is available
and the water tap is open.
2. Pour 2 litres of water into the detergent
compartment marked by
.
This action activates the drain system.
3. Pour a small quantity of detergent into the
compartment marked by
.
4. Set and start a programme for cotton at the
highest temperature without any laundry in the
drum.
This removes all possible dirt from the drum and
the tub.
Washer Dryer User Manual
37
Daily Use - Washing only
Washing heavily oiled, greasy stains
could cause damage to rubber
parts of the washing machine.
Warning! Refer to Safety
chapters.
Activating the appliance
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Press the On/Off button for a few seconds to
activate the appliance.
Filling the detergent and
additives
A short tune sounds.
Loading the laundry
1. Open the appliance door.
2. Empty the pockets and unfold the items before
you put them in the appliance.
3. Put the laundry in the drum, one item at a
time.
Do not put too much laundry in the drum.
4. Close the door firmly.
- Compartment for prewash phase, soak programme or stain remover.
- Compartment for washing phase.
- Compartment for fabric softener and other liquid treatments(fabric conditioner, starch).
- Maximum level for quantity of liquid additives.
- Flap for powder or liquid detergent.
Caution! Make sure that no
laundry gets caught between
the seal and the door to avoid
risk of water leakage and
damage to the laundry.
38
Washer Dryer User Manual
Always follow the instructions that
you find on the packaging of the
detergent products, but we
recommend that you do not
exceed the maximum indicated
level (
). This quantity will
however guarantee the best
washing results.
• Do not exceed to liquid detergent dose
indicated on the flap.
• Do not set the prewash phase.
• Do not set the delay start function.
5. Measure out the detergent and the fabric
conditioner.
6. Carefully close the detergent dispenser.
After a washing cycle, if necessary,
remove any detergent residue from
the detergent dispenser.
Check the position of the
detergent flap
1. Pull out the detergent dispenser until it stops.
Make sure that the flap does not cause a
blockage when you close the drawer.
Setting a programme
1. Turn the programme dial to select the desired
washing programme.
2. Press the lever down to remove the dispenser.
3. To use powder detergent, turn the flap up.
4. To use liquid detergent, turn the flap down.
The indicator of Mode - Wash button
illuminates.
The indicator of the Start/Pause button flashes.
The display shows an indicative programme
duration and the maximum load.
2. To change the temperature and/or the spin
speed, touch the related buttons.
3. If desired, set one or more options by touching
the related buttons. The related indicators
illuminate on the display and the given
information changes accordingly.
If a selection is not possible an
acoustic signal sounds and the
display shows
.
Starting a programme
With the flap in the position DOWN:
• Do not use gelatinous or thick liquid
detergents.
Washer Dryer User Manual
Touch the Start/Pause button to start the
programme. It is not possible to start the
programme when the indicator of the button is off
and doesn't flash (e.g. the door is open).
The related indicator stops flashing and stays on.
39
The programme starts, the door is locked. The
display shows the indicator
.
The drain pump can operate
shortly before the appliance fills
water.
Starting a programme with
the delay start
1. Touch the Delay start button repeatedly until
the display shows the desired delay time. The
related indicator comes on.
2. Touch the Start/Pause button. The appliance
door locks and starts the countdown of the
delay start. The display shows the indicator
.
When the countdown is completed, the
programme starts automatically.
Cancelling the delay start after the
countdown has started
To cancel the delay start:
1. Touch the Start/Pause button to pause the
appliance. The related indicator flashes.
2. Touch the Delay start button repeatedly until
the display shows .
3. Touch the Start/Pause button again to start
the programme immediately.
Changing the delay start after the
countdown has started
To change the delay start:
1. Touch the Start/Pause button to pause the
appliance. The related indicator flashes.
2. Touch the Delay start button repeatedly until
the display shows the desired delay time.
3. Touch the Start/Pause button again to start
the new countdown.
The SensiCare System load
detection
The programme duration in the
display is referred to a medium/
high load.
40
After touching the Start/Pause button, the
SensiCare System starts the laundry load
detection:
1. The appliance detects the load in the first 30
seconds. During this phase the Reduce time
bars
placed below the time digits play a
simple animation, the drum rotates shortly.
2. The programme duration will be adjusted
accordingly and could increase or decrease.
After further 30 seconds, the water filling
starts.
At the end of the load detection, in case of
drum overload, the indicator
is flashing
in the display:
In this case, for 30 seconds, it is possible to
pause the appliance and remove the exceeding
garments.
Once removed the exceeding garments, touch
the Start/Pause button to start the programme
again. The SensiCare phase can be repeated up
to three times (see point 1).
Important! If the laundry amount will not be
reduced, the washing programme starts anyway,
despite the overload. In this case, it will be not
possible to guarantee the best washing results.
About 20 minutes after the
programme start, the programme
duration could be adjusted again
depending on the capacity of water
absorption of the fabrics.
The SensiCare detection is carried
out with complete washing
programmes only and if the
programme duration has not been
reduced by means of the Reduce
time button.
Interrupting a programme and
changing the options
When the programme is running, you can
change only some options:
1. Touch the Start/Pause button.
Washer Dryer User Manual
The related indicator flashes.
2. Open the appliance door. If necessary, add or
remove the items. Close the door and touch
the Start/Pause button.
The washing programme continues.
End of the programme
Cancelling a running
programme
When the programme has finished, the
appliance stops automatically. The acoustic
signals operate (if they are active). The display
shows
2. Change the options. The given information in
the display changes accordingly.
3. Touch the button Start/Pause again.
1. Press the button On/Off to cancel the
programme and to deactivate the appliance.
2. Press the button On/Off again to activate the
appliance.
If the SensiCare System has
completed and the water filling has
already started, the new
programme starts without
repeating the SensiCare
System. The water and the
detergent are not drained out in
order to avoid waste. The display
shows the maximum duration of
the programme, updating it about
20 minutes after the starting of the
new programme.
There is also an alternative way of cancelling:
1. Rotate the selector knob to the "Reset"
position .
2. Wait for 1 second. The display shows
.
Now, you can set a new washing programme.
Opening the door - Adding
garments
If the temperature and level of the
water in the drum are too high
and/or the drum is still rotating
you should not open the door.
While a programme or the delay start operates,
the appliance door is locked. The display shows
.
the indicator
1. Touch the Start/Pause button.
In the display the related door lock indicator
goes off.
Washer Dryer User Manual
The indicator of the Start/Pause button goes
off.
The door unlocks and the indicator
off.
goes
1. Press button On/Off to deactivate the
appliance.
After five minutes from the end of the
programme, the energy saving function
automatically deactivates the appliance.
When you activate the appliance
again, the display shows the end of
the previous programme. Turn the
programme dial to set a new cycle.
2. Remove the laundry from the appliance.
3. Make sure that the drum is empty.
4. Keep the door and the detergent dispenser
slightly ajar to prevent mildew and odours.
5. Close the water tap.
Draining water out after end
of cycle
If you have chosen a programme or an option
that does not empty out the water of the last
rinse, the programme is completed, but:
• The time area shows
and the display
shows the door locked
.
• The indicator of the Start/Pause button starts
flashing.
• The drum still turns at regular intervals to
prevent creases in the laundry.
• The door stays locked.
• You must drain the water to open the door:
1. If necessary, touch the Spin button to decrease
the spin speed proposed by the appliance.
41
2. Press the Start/Pause button: the appliance
drains the water and spins.
The option indicator Rinse Hold
disappears.
If you have selected No Spin
, the appliance will only drain
the water.
3. When the programme is completed and the
door locked indicator
goes off, you can
open the door.
4. Press the On/Off button for a few seconds to
deactivate the appliance.
Stand-by function
The Stand-by function automatically deactivates
the appliance to reduce the energy consumption
when:
• You do not use the appliance for 5 minutes
when no programme is running.
Press the button On/Off to activate the
appliance again.
• 5 minutes after the end of the washing
programme.
Press the On/Off button to activate the
appliance again.
The display shows the end of the last
programme.
Turn the programme dial to set a new cycle.
If the dial is rotated to the "Reset" position
the appliance automatically turns off in 30
seconds.
,
If you set a programme or an
option that ends with water in the
drum, the Stand-by function
doesn't deactivate the appliance
to remind you to drain the water.
42
Washer Dryer User Manual
Daily use - Washing & Drying
Warning! Refer to Safety
chapters.
This appliance is an automatic
washer dryer.
Complete wash&dry
programme
Automatic Non-Stop programme or
programmes
Depending on the model, the appliance may be
equipped with one or more Wash & Dry
programmes, automatic wash&dry programmes
where it is not necessary to set the Mode - Dry.
washing only mode and the indicator of the
Mode - Wash button is on. The display shows
the default temperature and spin. If necessary,
change them according to your laundry.
5. Set the desired options, if there are available.
6. Tap on the Mode button once to activate also
the drying function. Both indicators of the
Mode - Wash and Mode - Dry buttons are on.
The indicator
appears on the display.
Washing and Drying Automatic levels
1. Tap on the Auto dry button repeatedly until
the display shows the required dryness level.
The indicators in the display illuminate
accordingly:
Proceed as follows:
a.
Iron dry: for cotton items;
1. After loading laundry and detergent, press the
On/Off button for some seconds to activate
the appliance.
2. Set the Wash & Dry programme by means of
the programme dial.
3. Touch the Start/Pause button to start the
programme.
b.
Cupboard dry: for cotton and
synthetic items;
c.
Extra dry: for cotton items.
Non-automatic wash&dry programmes
In some washing programmes, you can combine
Mode - Wash and Mode - Dry for running a
complete wash&dry programme.
Proceed as follows:
1. Press the On/Off button for some seconds to
activate the appliance.
2. Load the laundry one item at a time.
3. Put the detergent and the additives in the
appropriate compartment.
4. Turn the programme dial to the washing
programme. The appliance defaults to the
Washer Dryer User Manual
The time value on the display is the
duration of both cycles washing and
drying, calculated on a default load size.
To have a good drying by using less
energy and in a shorter time, the
appliance does not let you set a
too low spin speed for the items to
be washed and dried.
2. Touch button Start/Pause to start the
programme. The SensiCare estimation starts.
indicator
In the display the door locked
comes on.
The display also shows the remaining
programme time.
43
Washing and Timed Drying
1. Tap on the Time dry button repeatedly to set
the desired time value (see the "Timed drying"
table the "Programmes" chapter). The drying
level indicator
comes on.
goes off and the indicator
Each time you tap on this button the time value
increases by 5 minutes. The display shows the
set new time value.
2. Touch the Start/Pause button to start the
programme. The SensiCare estimation starts.
In the display the door locked
indicator
comes on.
The display also shows the remaining
programme time.
At the end of the drying
programme
• The appliance stops automatically.
• The acoustic signals operate (if they are active).
• In the display
comes on.
• The indicator of the Start/Pause button goes
indicator goes off and
off. The door locked
the door unlocks.
• Press the On/Off button for some seconds to
deactivate the appliance.
After some minutes from the
end of the programme, the
energy saving function
deactivates the appliance
automatically.
1. Remove the laundry from the appliance.
2. Make sure that the drum is empty.
After drying phase, clean the drum,
the seal and the inside of the door
with a wet cloth.
44
Washer Dryer User Manual
Daily use - Drying only
Warning! Refer to Safety
chapters.
This appliance is an automatic
washer dryer.
Preparation to drying
1. Press the On/Off button for some seconds to
activate the appliance.
2. Load the laundry one item at a time.
3. Turn the programme dial to the programme
suitable for the items to dry. The appliance
defaults to the washing only mode and the
indicator of the Mode - Wash button is on.
4. Tap on the Mode button twice to perform
drying only. The indicator of Mode - Dry
button illuminates and the indicator of Mode Wash button goes off.
When drying a big amount of
laundry, to have good drying
performances, make sure that the
laundry itself is not rolled up and
that is uniformly distributed in the
drum.
Drying - Automatic levels
1. Tap on the Auto dry button repeatedly until
the display shows the required dryness level.
The indicators in the display illuminate
accordingly:
a.
Iron dry: for cotton items;
b.
Cupboard dry: for cotton and
synthetic items;
c.
Extra dry: for cotton items.
2. Touch the Start/Pause button to start the
programme.
In the display the door locked
indicator
comes on.
The display also shows the remaining
programme time.
Timed Drying
1. Tap on the Time dry button repeatedly to set
the desired time value (see the "Timed drying"
table the "Programmes" chapter). The drying
level indicator
comes on.
goes off and the indicator
Each time you tap on this button the time value
increases by 5 minutes. The display shows the
set new time value.
2. Touch the Start/Pause to start the
programme.
In the display the door locked
indicator
comes on.
The display also shows the remaining
programme time.
At the end of the drying
programme
• The appliance stops automatically.
• The acoustic signals operate (if they are active).
• In the display
comes on.
• The indicator of the Start/Pause button goes
indicator goes off and
off. The door locked
the door unlocks.
• Press the On/Off button for some seconds to
deactivate the appliance.
The display shows the drying programme
duration.
Washer Dryer User Manual
45
After some minutes from the
end of the programme, the
energy saving function
deactivates the appliance
automatically.
1. Remove the laundry from the appliance.
2. Make sure that the drum is empty.
After drying phase, clean the drum,
the seal and the inside of the door
with a wet cloth.
46
Washer Dryer User Manual
Fluff in the fabrics
During the washing and/or drying phase, some
types of fabric, (sponge, wool, sweatshirt) could
release fluff.
The released fluff could stick to the fabrics
during the next cycle.
This inconvenient increases with technical
fabrics.
To prevent the fluff in your laundry, we
recommend that you:
• To do not wash dark fabrics after you washed
and dried light coloured fabrics (hand towel,
wool, sweatshirt ) and the contrary.
• To dry this type of fabrics at open air when they
are washed the first time.
• To clean the drain filter.
• After the drying phase, clean the empty drum,
the gasket and the door with a wet cloth.
To remove the fluff inside the drum, set
a special programme:
• Empty the drum.
• Clean the drum, the gasket and the door with a
wet cloth.
• Set the Machine Clean programme and the
Mode - Dry together to activate the anti-fluff
action.
• Touch the Start/Pause button to start the
programme.
If the appliance is frequently used,
carry out the cleaning programme
regularly.
Washer Dryer User Manual
47
Hints and tips
Warning! Refer to Safety
chapters.
The laundry load
• Divide the laundry into: white, coloured,
synthetics, delicates and wool.
• Follow the washing instructions on the laundry
care labels.
• Do not wash white and coloured items
together.
• Some coloured items can discolour with the
first wash. We recommend that you wash them
separately for the first couple of times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Turn multilayered fabrics, wool and items with
printed illustrations inside out.
• Pre-treat tough stains.
• Wash heavy soil stains with a special detergent.
• Be careful with curtains. Remove the hooks and
put the curtains in a washing bag or pillowcase.
• Do not wash laundry without hems or with
cuts.
• Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
• A very small load can cause balance problems
with the spin phase leading to excessive
vibration. If this occurs:
a. interrupt the programme and open the
door (refer to "Daily Use" chapter);
b. manually redistribute the load so that the
items are spaced evenly around the tub;
c. press the Start/Pause button. The spin
phase continues.
• Avoid washing garments full of long animal hair
or poor quality garments releasing lots of fluff
that could block the drain circuit and therefore
requiring the Service assistance.
• Empty pockets and unfold the items.
48
Stubborn stains
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the
type of stain and fabric.
Detergents and other
treatments
• Only use detergents and other treatments
specially made for washing machines:
– powder detergents for all types of fabric,
excluding delicate. Prefer powder
detergents containing bleach for whites and
laundry sanitization
– liquid detergents, preferably for low
temperature wash programmes (60 °C
max) for all types of fabric, or special ones
for woollens only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the recommended quantity of detergent.
• Follow the instructions that you find on
packaging of the detergents or other treatments
without exceeding the indicated maximum level
(
).
Washer Dryer User Manual
• Use the recommended detergents for the type
and colour of the fabric, the programme
temperature and the level of soil.
Ecological hints
• Set a programme without the prewash phase to
wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry allowed.
• If you pre-treat the stains or use a stain
remover, set a programme with a low
temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
Water hardness
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where
the water hardness is soft it is not necessary to
use a water softener.
To find out the water hardness in your area,
contact your local water authority.
Use the correct quantity of water softener.
Follow the instructions that you find on the
packaging of the product.
Prepare the drying cycle
• Open the water tap.
• Check if the drain hose is connected properly.
Refer to installation chapter for more
information.
• For the maximum laundry load of the drying
programmes, refer to the drying programmes
table.
Items not suitable for drying
Do not set a drying programme for this
laundry:
•
•
•
•
•
Synthetic curtains.
Pieces of clothing with metal inserts.
Nylon stockings.
Quilts.
Bed covers.
Washer Dryer User Manual
•
•
•
•
Duvets.
Anoraks.
Sleeping bags.
Fabrics with residue of hair sprays, nail solvents
or similar.
• Garments with foam-rubber or materials similar
to foam-rubber.
Garment labels
When you dry the laundry, obey the indications
on the labels of the manufacturers:
•
= The item can be tumble dried
•
= The drying cycle is at high temperature
•
•
= The drying cycle is at reduced
temperature
= The item can not be tumble dried.
Drying cycle duration
The drying time can change depending on:
•
•
•
•
speed of the last spin
dryness level
type of laundry
weight of the load
Additional drying
If, at the end of the drying programme, the
laundry is still damp, set a short drying cycle
again.
Warning! To avoid creasing
and shrinkage do not overdry
the laundry.
General Tips
Refer to the «Drying programmes» table to find
the average drying times.
Experience will help you to dry the laundry
better. Take note of the duration of the cycles
done before.
To avoid the static charge at the end of the
drying cycle:
1. Use fabric conditioner in the washing cycle.
49
2. Use special fabric conditioner for tumble
dryers.
When the drying programme is completed
remove the laundry promptly.
50
Washer Dryer User Manual
Care and cleaning
Warning! Refer to Safety
chapters.
External cleaning
Clean the appliance with mild soap and warm
water only. Fully dry all the surfaces.
Caution! Do not use alcohol,
solvents or chemical
products.
Caution! Do not clean the
metal surfaces with chlorinebased detergent.
Descaling
the drum and the tub. This could generate bad
odours and mildew. To eliminate these deposits
and clean the inner part of the appliance, run a
maintenance wash regularly (at least once a
month).
Refer to Cleaning the drum
chapter.
Door seal with double lip trap
This appliance is designed with a self cleaning
draining system, allowing light fluff fibers that
fall off the clothes to be drained out with the
water, in such a way that there is no need by the
customer to access this area for regular
maintenance and cleaning.
If the water hardness in your area is
high or moderate, we recommend
that you use a water descaling
product for washing machines.
Regularly examine the drum to check for
limescale.
Regular detergents already contain water
softening agents, but we recommend to run a
cycle with an empty drum and a descaling
product occasionally.
Always follow the instructions that
you find on the packaging of the
product.
Maintenance wash
The repeated and prolonged use of low
temperature programmes can cause detergent
deposits, fluff residues, bacterial growth inside
Washer Dryer User Manual
Regularly examine the seal and remove all
objects from the inner part. Coins, buttons,
other small items forgotten in the pockets of
your clothes are deposited during the washing
cycle in the special double lip trap in the
porthole seal, where they can be conveniently
recovered at the end of the cycle.
Cleaning the drum
Regularly examine the drum to prevent
unwanted deposits.
51
Rust deposits in the drum may occur due to
rusting foreign body in the washing or tap water
containing iron
cleaning, put the top part back into position.
Clean the drum with special products for
stainless steel.
Always follow the instructions that
you find on the packaging of the
product.
Do not clean the drum with acidic
descaling products, scouring
products containing chlorine or
iron or steel wool.
For a thorough clean:
1. Remove all laundry from the drum.
2. Run the Machine Clean programme. For more
details, refer to washing programme table.
3. Add a small quantity of powder detergent into
the empty drum, in order to rinse out any left
residues.
3. Make sure that all detergent residue is
removed from the upper and lower part of the
recess. Use a small brush to clean the recess.
Cleaning the detergent
dispenser
To prevent possible deposits of dried detergent
or clotted fabric softener and/or formation of
mould in the detergent dispenser drawer, once
in a while carry out the following cleaning
procedure:
4. Insert the detergent drawer into the guide rails
and close it. Run the rinsing programme
without any clothes in the drum.
1. Open the drawer. Press the catch downwards
as indicated in the picture and pull it out.
2. Remove the top part of the additive
compartment to aid cleaning and flush it out
under running warm water, to remove any
traces of accumulated detergent. After
52
Washer Dryer User Manual
Cleaning the drain pump
Warning! Disconnect the
mains plug from the mains
socket.
Regularly check the drain pump
filter and make sure that it is clean.
Clean the drain pump if:
• The drum does not turn.
• The appliance makes an unusual noise because
of the blockage of the drain pump.
• The display shows the alarm code
.
Warning!
• Do not remove the filter while
the appliance operates.
• Do not clean the pump if the
water in the appliance is hot. Wait
until the water cools down
• The appliance does not drain the water.
Proceed as follows to clean the pump:
2
1. Open the pump cover.
1
2. Place a suitable bowl below the drain pump access to
collect the water that flows out.
Always keep a rag nearby to dry up any water spillages
when removing the filter.
Washer Dryer User Manual
53
180˚
3. Turn the filter 180 degrees in anti-clockwise direction
to open it, without removing. Let the water flow out.
4. When the bowl is full of water, turn the filter back and
empty the container.
5. Repeat the steps 4 and 5 until the water stops to flow
out.
1
6. Turn the filter anti-clockwise to remove it
2
7. If it is necessary, remove fluff and objects from the filter
recess.
Make sure that the impeller of the pump can rotate. If it
does not rotate, contact the Authorised Service Centre.
54
Washer Dryer User Manual
8. Clean the filter under the water tap.
2
9. Put the filter back into the special guides by turning it
clockwise. Make sure that you tighten the filter correctly
to prevent leakages.
1
2
10. Close the pump cover.
1
When you drain the water with the emergency drain procedure, you must activate the drain system again:
1. Put 2 litres of water in the main wash compartment of the detergent dispenser.
2. Start the programme to drain the water.
Washer Dryer User Manual
55
Cleaning the inlet hose and the valve filter
1
2
3
45°
20°
Emergency drain
If the appliance cannot drain the water, carry
out the same procedure, described in 'Cleaning
the drain pump' paragraph. If necessary, clean
the pump.
When you drain the water with the emergency
drain procedure, you must activate the drain
system again:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the water.
Frost precautions
If the appliance is installed in an area where the
temperature can reach values around 0° C or
drop below, remove the remaining water from
the inlet hose and the drain pump.
56
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
Warning! Make sure that the
temperature is higher than 0
°C before you use the
appliance again.
The manufacturer is not
responsible for damages
caused by low temperatures.
Washer Dryer User Manual
Troubleshooting
Warning! Refer to Safety
chapters.
Introduction
The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists, contact the
Authorised Service Centre.
Warning! Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an alarm
code and the Start/Pause button may flash continuously:
•
- The mains supply is unstable. Wait until the mains supply is stable.
•
- No communication between electronic elements of the appliance. Switch it off and switch on
again. The programme was not finished properly or the appliance stopped too early. If the alarm code
appears again, contact the Authorised Service Centre.
•
- The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the
Authorised Service Centre.
•
- The appliance does not fill with water properly. After the proper check, start the appliance
again by pressing Start/Pause button the appliance tries to resume the cycle . If the error persists the
alarm code will appear again.
•
- The appliance does not drain the water.
•
- The appliance door is open or not closed correctly. Please check the door!
If the appliance is overloaded, remove some items from the drum and/or hold the
door shut while touching the Start/Pause button until the indicator
stops
flashing (see the picture below).
Washer Dryer User Manual
57
Possible failures
Problem
Possible solution
•
•
•
•
The programme does not start.
•
•
•
•
•
The appliance does not fill with •
water properly.
•
•
•
The appliance fills with water
and drains immediately
The appliance does not drain
the water.
58
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is no damaged fuse in the fuse box.
Make sure that the Start/Pause has been touched.
If the delay start is set, cancel the setting or wait for the end of countdown.
Deactivate the Child Lock function if it is on.
Check the position of the knob on the selected programme.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the inlet hose has no kinks, damages or bends.
Make sure that the connection of the water inlet hose is correct.
Make sure that the filter of the inlet hose and the filter of the valve are not
clogged. Refer to 'Care and cleaning'.
•
Make sure that the drain hose is in the correct position. The hose may be
positioned too low. Refer to "Installation instruction".
•
•
•
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary.
Refer to "Care and cleaning".
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain phase.
Set the drain programme if you set an option which ends with water in the
tub.
•
•
•
Washer Dryer User Manual
Problem
The spin phase does not operate or the washing cycle lasts
longer than usual.
Possible solution
•
•
•
•
There is water on the floor.
•
•
•
You cannot open the appliance
door.
•
•
•
•
•
The appliance makes an unusual noise and vibrates.
•
•
The programme duration increases or decreases during
programme execution.
The washing results are not
satisfactory.
Too much foam in the drum
during the washing cycle.
After the washing cycle, there
are some detergent residues in
the dispenser drawer.
Washer Dryer User Manual
Set the spin programme.
Make sure that the drain filter is not clogged. Clean the filter, if necessary.
Refer to "Care and cleaning".
Adjust manually the items in the tub and start the spin phase again. This
problem may be caused by balance problems.
Make sure that the couplings of the water hoses are tight and there is not
water leakages.
Make sure that the water inlet hose and the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of it.
Make sure that a washing programme that ends with water in tub, has
been selected.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
Make sure that the appliance receives electrical power.
This problem may be caused by a failure of the appliance. Contact the Authorised Service Centre.
If you need to open the door, please read carefully "Emergency door
opening".
Make sure the levelling of the appliance is correct. Refer to "Installation instruction".
Make sure that the packaging and/or the transit bolts are removed. Refer
to "Installation instruction".
Add more laundry in the drum. The load may be too small.
•
The SensiCare System is able to adjust the programme duration according
to the type and the laundry load size. Refer to "The SensiCare System load
detection" in "Daily Use" chapter.
•
•
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you wash the
laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
•
Reduce the quantity of detergent.
•
Make sure that the flap is in the correct position (UP for powder detergent - DOWN for liquid detergent).
Make sure you have used the detergent dispenser according the indications given in this user manual.
•
59
Problem
The appliance does not dry or
does not dry correctly.
The laundry is full of different
colours fluff.
Possible solution
•
•
•
•
Turn the water tap on.
Make sure the drain filter is not clogged.
Reduce the laundry load.
Make sure you have set the correct cycle. if necessary, set again a short
drying time.
The fabrics washed in the previous cycle released fluff of a different colour:
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum run the special programme
to clean it (refer to “Fluff in the fabrics" for more details).
After the check, activate the appliance. The programme continues from the point of interruption.
If the problem occurs again, contact the Authorised Service Centre.
Emergency door opening
In case of power failure or functioning failure the
appliance door remains locked. The washing
programme continues when the power is
restored. If the door remains locked in case of
failure, it is possible to open it using the
emergency unlock function.
Before opening the door:
1. Press the On/Off button to switch the
appliance off.
2. Disconnect the mains plug from the mains
socket.
3. Pull the emergency unlock trigger downward
once. Pull it once again, keep it tensed and, in
the meanwhile, open the appliance door. The
emergency unlock trigger is located where
indicated by the following picture.
Caution! Risk of burns! Make
sure that the water
temperature is not too high
and the laundry is not hot. If
necessary, wait until they cool
down.
Caution! Risk of injury! Make
sure that the drum is not
rotating. If necessary, wait
until the drum stops rotating.
Make sure that the water
level inside the drum is not
too high. If necessary,
proceed with an emergency
drain (refer to «Emergency
drain» in «Care and cleaning»
chapter).
4. Take out the laundry and then close the
appliance door.
To open the door, proceed as follows:
60
Washer Dryer User Manual
Consumption values
Stated values are obtained in laboratory conditions with relevant standards. Different
causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also
affect the washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
Programmes
Load
(kg)
Energy
Water conconsumpsumption (lition (kWh) tre)
Approximate programme duration (minutes)
Cottons 60°C
7
1.08
79
205
Cotton eco
Cotton Energy Saving Programme
7
0.80
52
265
Cottons 40°C
7
0.8
79
190
Synthetics 40°C
3
0.58
72
140
Delicates 40°C
2
0.42
46
64
Wool/Handwash 30°C
1.5
0.15
59
70
60°C1)
1) «Cotton Energy Saving programme » at 60°C with a load of 7kg is the reference programme for the data entered in the energy
label, in compliance with 96/60/EC Directive.
Washer Dryer User Manual
61
Technical Data
Dimension
Width/ Height/ Depth/ Total
depth
596 mm/ 819 mm/ 540 mm/ 553 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
2000 W
13 A
50 Hz
Level of protection against ingress of solid particles and moisture IPX4
ensured by the protective cover, except where the low voltage
equipment has no protection against moisture
Cold water
Water supply 1)
Water supply pressure
2)
Minimum
Maximum
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Maximum wash load
Cotton
7 kg
Maximum dry load
Cotton
Synthetics
4 kg
3 kg
Spin Speed
Maximum spin speed
1550 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
2) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot connect the water inlet
hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not
to exceed a distance of 5.02 m (16.5 ft) between the appliance inlet hose and the bottom of the water storage tank.
62
Washer Dryer User Manual
Repairs - after sales service
Your John Lewis appliance comes with a three
year guarantee. Your original receipt acts as
your guarantee. Please make sure you retain it.
The guarantee does not cover you against faults
caused by accidental damage or misuse. For
further details visit johnlewis.com/customerservices. If it is not working correctly refer to
the "Troubleshooting" chapter in this user
manual. If a fault occurs which you can not
resolve through following the advice and
information contained within this instruction
manual, the next step is to contact John Lewis
technical support on:
0330 1230106
They will give you details for your local service
engineer. Before calling out an engineer, please
ensure you have read the details under the
heading “Troubleshooting”.
When you contact your local service engineer
you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of fault
The purchase date as found on your receipt
The model and serial number of the appliance.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
• Mod.......................................
• P.N.C.....................................
• S.N.........................................
IMPORTANT: If you call out an engineer
to a fault listed under the heading
''Troubleshooting'', or to repair a fault
caused by incorrect use or installation, a
charge will be made even if the appliance
is under guarantee.
Spare parts
Washer Dryer User Manual
Always insist on genuine spare parts.
An authorised service engineer should service
this product, and only genuine spare parts
should be used. Under no circumstances should
you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons
may cause injury or serious malfunctioning.
Please contact John Lewis technical support on
0330 1230106 for assistance.
Shopping is easy with John Lewis Shops
John Lewis, Aberdeen 01224 625 000
John Lewis, Basingstoke 01256 406200
John Lewis, Bluewater 01322 624 123
John Lewis, Brent Cross 020 8202 6535
John Lewis, Birmingham 0345 604 9049
John Lewis, Cambridge 01223 361 292
John Lewis, Cardiff 02920 536 000
John Lewis, Cheadle 0161 491 4914
John Lewis, Chelmsford 0124 545 8400
John Lewis, Cribbs Causeway 0117 959 1100
John Lewis, Edinburgh 0131 556 9121
John Lewis, Exeter 01392 284150
John Lewis, Glasgow 0141 353 6677
John Lewis, High Wycombe 01494 462 666
John Lewis, Kingston 020 8547 3000
John Lewis, Leicester 0116 242 5777
John Lewis, Leeds 0113 3946299
John Lewis, Liverpool 0151 709 7070
John Lewis, Milton Keynes 01908 679 171
John Lewis, Newcastle upon Tyne 0191 232 5000
John Lewis, Norwich 01603 660 021
John Lewis, Nottingham 0115 941 8282
John Lewis, Oxford Street 020 7629 7711
John Lewis, Peterborough 01733 344 644
John Lewis, Reading 0118 957 5955
John Lewis, Sheffield 0114 276 8511
Peter Jones, Sloane Square 020 7730 3434
John Lewis, Solihull 0121 704 1121
63
John Lewis, Southampton 02380 216 400
Knight & Lee, Southsea 02392 827 511
John Lewis, Stratford 020 8532 3500
John Lewis, The Trafford Centre 0161 491 4040
John Lewis, Watford 01923 244 266
John Lewis, Welwyn 01707 323 456
John Lewis at home
John Lewis, Ashford 01233 811 010
John Lewis, Chester 01244 393 880
64
John Lewis, Chichester 01243 813 030
John Lewis, Croydon 020 8662 4730
John Lewis, Horsham 01403 214 740
John Lewis, Ipswich 01473 275 850
John Lewis, Newbury 01635 263 980
John Lewis, Poole 01202 756 020
John Lewis, Swindon 01793 733 180
John Lewis, Tamworth 01827 300 580
John Lewis, Tunbridge Wells 01892 506 830
John Lewis, York 01904 557 950
Washer Dryer User Manual
Environmental concerns
marked with the symbol with the household
waste. Return the product to your local
recycling facility or contact your municipal office.
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it.
Help protect the environment and human health
by recycling waste of electrical and electronic
appliances. Do not dispose of appliances
Washer Dryer User Manual
65
*
66
Washer Dryer User Manual
Washer Dryer User Manual
67
157026070-A-482018 ( Subject to change without notice. )
">