Satrap OP50GSA+ User Manual

Satrap OP50GSA+ User Manual
Gefrierschrank
Congelateur
Congelatore
Freezer
Gebrauchsanleitung
Mode d’emploi
Libretto d’istruzioni
Istruction book
DE
FR
IT
GB
200369750
SV/S/14-2. (05.)
GB
Before installing and using the appliance read this user's instruction book carefully. It contains safety
precautions, hints, information and ideas. If the refrigerator is used in compliance with the
instructions written, it will operate properly and provide you with greatest satisfaction.
The symbols below help you to find things more easily:
Safety precautions
Warnings and information at this symbol serve safety for you and your appliance.
Hints, useful information
Environmental information
Symbol for ideas
At this symbol ideas can be found according to food and its storing.
The symbol on the product or on its packaging indicates that this product may not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this
product. For more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you purchased the
product.
38
GB
Cont ents
Important safety information ..................................................................................................40
General safety precautions ....................................................................................................40
Precautions for child safety....................................................................................................40
Safety precautions for installation ...........................................................................................40
Safety precautions for isobutane ............................................................................................40
Instruction for the User...........................................................................................................41
General information ..............................................................................................................41
Description of the appliance, main parts ..................................................................................41
Instructions for the Installer....................................................................................................42
Technical data .....................................................................................................................42
Transportation, unpacking.................................................................................................42
Cleaning ........................................................................................................................42
Placement ......................................................................................................................43
Putting it into use.............................................................................................................44
Controlling the temperature ...............................................................................................44
Freezing.........................................................................................................................44
Storing...........................................................................................................................45
How to make ice cubes ....................................................................................................45
Some useful information and advice........................................................................................45
Hints and ideas ...................................................................................................................45
How to save energy .........................................................................................................45
The appliance and environment .........................................................................................45
Maintenance .......................................................................................................................46
Defrosting ......................................................................................................................46
Regular cleaning .............................................................................................................46
When the refrigerator is not in use ......................................................................................47
Trouble shooting ..................................................................................................................47
Change of door opening direction ......................................................................................48
Electrical connection........................................................................................................49
Warranty and service .............................................................................................................50
Guarantee conditions ...........................................................................................................50
Service and spare parts........................................................................................................50
39
GB
Im por t ant saf et y inf ormation
General safety precautions
Keep these instructions and they should remain at
the appliance when moving away or changing
owner.
This appliance is designed for storing food,
domestic use and being used according to these
instructions only.
Specialised companies that are qualified to do
so by the manufacturer must carry out service
and repairs including repairing and changing
the power cord. Accessory parts supplied by
them should be used only for repairing. Otherwise
the appliance can be damaged or can cause other
damage or injury.
The appliance is out of circuit only in that case if the
plug is removed from the socket. Before cleaning
and maintenance always unplug it (do not get it by
the cable). If the socket is difficult to reach, switch
off the appliance by cutting off the current.
Power cord must not be lengthened.
When cleaning, defrosting, taking out frozen food
or ice tray do not use sharp, pointed or hard
devices, as they can cause damage to the
appliance.
Be careful not to allow liquids to the temperature
control.
Ice and ice-cream can cause hurt if they are eaten
immediately after removal from the frozen food
compartment.
After dissolving frozen food must not be refrozen, it
must be used up as soon as possible.
Store pre-packed frozen food in accordance with
the frozen food manufacturer's instructions.
You must not make defrosting faster with any
electric heating appliance or chemicals.
Do not put hot pot to the plastic parts of the freezer.
Do not store flammable gas and liquid in the
appliance, because they may explode.
Do not store carbonated drinks, bottled drinks and
bottled fruits in the freezer.
Precautions for child safety
Do not allow children to play with the packaging of
the appliance. Plastic foil can cause suffocation.
Adults must handle the appliance. Do not allow
children to play with it or its controlling parts.
40
If you are discarding the appliance pull the plug
out of the socket, cut the connection cable (as
close to the appliance as you can) and remove
the door to prevent playing children to suffer
electric shock or to close themselves into it.
Safety precautions for
installation
Put the appliance to the wall to avoid touching or
catching warm parts (compressor, condenser)
to prevent possible burn.
When moving the appliance take care of the plug
not to be in the socket.
When placing the appliance take care not to
stand it on the power cord.
Adequate air circulation should be around the
appliance, lacking this leads to overheating. To
achieve sufficient ventilation follow the
instructions relevant to installation.
If the appliance is not placed on floor level,
provide appropriate fixing (e. g. using sucking
disks).
See chapter "Placement".
Safety precautions for
isobutane
Warning
The refrigerant of the appliance is isobutane
(R600a) that is inflammable and explosive to a
greater extent.
Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of
obstruction.
Do not use mechanical devices or other means
to accelerate the defrosting process, other than
those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance, unless
they are of the type recommended by the
manufacturer.
For the safety of life and property keep
the precautions of these user's
instructions as the manufacturer is not
responsible for damages caused by omission.
GB
Ins tr uctions f or the User
General information
The official designation of the appliance is home
freezer. According to this the appliance is suitable for
storing frozen and deep-frozen food, freezing
products in quantity given in the user's instructions at
home and making ice.
The appliance can meet the requirements of
standards between different temperature limits
according to the climate class.
The letter symbol for climate class can be found on
the data plate.
Description of the appliance, main parts
1. Freezing compartment
8. Door gasket
2. Data plate
9. Thermostat with knob
3. Storing compartment
10. Condenser
4. Freezing shelf
11. Air circulation
5. Defrost water outlet
12. Compressor
6. Ice tray
13. Spacer
7. Legs
41
GB
Ins tr uctions f or the Ins t aller
Technical data
Model
Gross capacity (l)
Net capacity (l)
Width (mm)
Height (mm)
Depth (mm)
Energy consumption
(kWh/24h)
(kWh/year)
Energy class, according to EU
Standards
Freezing capacity (kg/24h)
Rising time (h)
Rated power (W)
Weight (kg)
OECOPLAN 50 GS A+
50
50
525
520
580
0,42
153
A+
7
17
60
25
Transportation, unpacking
It is recommended to deliver the appliance in
original packaging, in vertical position
considering the protective warning on packaging.
After each transportation the appliance must not be
switched on for approx. 2 hours.
Unpack the appliance and check if there are damages
on it. Report possible damages immediately to the
place you bought it. In that case retain packaging.
Cleaning
Remove every adhesive tape, which ensure the parts
not to move in the appliance.
Wash the inside of the appliance using lukewarm
water and mild detergent. Use soft cloth.
After cleaning wipe out the inside of the appliance.
42
GB
Placement
The ambient temperature has an effect on the energy
consumption and proper operation of the appliance.
When placing, take into consideration that it is
practical to operate the appliance between ambient
temperature limits according to the climate class that
is given in the chart below and can be found in the
data label.
Class of climate
Ambient temperature
SN
+10 ... +32 °C
N
+16 ... +32 °C
ST
+18 ... + 38 °C
If the ambient temperature goes below the lower data
the temperature of the cooling compartment can go
beyond the prescribed temperature.
If the ambient temperature goes beyond the upper
data this means longer operating time of the
compressor, increasing temperature in the cooling
compartment or increasing energy consumption.
When placing the appliance ensure that it stands level.
Mount the spacers supplied in the plastic bag of
the accessories. Hold the spacer as shown on the
Fig., using fine strokes of hammer put it in its
place.
Do not stand the appliance on a sunny place or close
to a radiator or cooker.
If it is unavoidable because of furnishing and the
appliance has to be stood near a cooker take these
minimum distances into consideration:
In case of gas or electric cooker 3 cm must be left,
when it is less put a 0,5-1 cm non-flam insulation
between the two appliances.
In case of oil or coal-fired stove the distance must
be 30 cms since they give off more heat.
The refrigerator is designed to operate when it is
totally pushed to the wall.
When placing the refrigerator keep minimal
distances recommended in figure.
A : placing it under a wall-cupboard
B : placing it freely
43
GB
Putting it into use
Put the plug into the mains socket.
Turn the thermostatic control knob to „SUPER”
position according to the figure and operate the
appliance at least for 4 hours.
Then reset the thermostatic control knob to
„NORMAL” position. This time the appliance is
suitable for storing frozen and deep-frozen foods.
Controlling the temperature
The thermostatic controller interrupts the operation of
the appliance automatically for more or less time
depending on the setting then restarts it assuring the
required temperature.
Setting the thermostat knob can be done by rotation.
Turning the control knob clockwise cooling becomes
more and more intensive.
In the appliance -18 °C or lower temperature can be
reached if the thermostat knob is set to „NORMAL”
position according to the figure.
The thermostat can be switched off („STOP” position),
which means breaking the circuit of the compressor
i.e. stopping cooling.
The temperature coming about in the freezer is
effected by not only the position of the thermostatic
control and the ambient temperature, but frequency of
door openings and the quantity of food put into it, etc.
In maximum position of the thermostat - in case
of increased demand e.g. during heatwaves the compressor may operate continually. This does
not cause damages to the appliance.
Freezing
Freezing different products should always be done in
the freezing compartment after proper preparing.
Set the thermostatic control knob to „SUPER” position
4 hours before freezing food in small quantity and
about 24 hours before in case of products in bigger
quantity. This time the compressor operates
continually to reach temperature necessary for
freezing.
Place the foods to be frozen in and operate the
appliance as written for about 24 hours.
After these reset the thermostatic control knob to
„NORMAL” position.
44
GB
Storing
It is practical to replace frozen products into the
storing compartment after freezing has finished so
that to make room in the freezing compartment for
another freezing.
Do not leave the door open longer than
necessary and avoid unnecessary openings.
Put warm foods into the appliance only when
they are at room temperature.
The condenser must be kept clean.
Intermediate freezing does not deteriorate foods
already stored.
The appliance and environment
How to make ice cubes
To make ice cubes fill the enclosed ice cube tray with
water and put it to the frozen food compartment.
Wetting the bottom of the tray can shorten preparing
time.
Ready ice cubes can be taken out of the tray under
running water then twist or hit it.
Some useful information and
advice
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with the
urban refuse and rubbish. Avoid damaging the
cooling unit, especially at the rear near the heat
exchanger. Information on your local disposal sites
may be obtained from your municipal authorities.
The materials used on this appliance marked with
the sympol
are recyclable.
After opening and closing the door of freezer
vacuum will rise inside the appliance because of
the low temperature. So wait 2-3 minutes after
closing the door - if you want to open it again - while
inner pressure equalises.
Take care of operating the freezer at a position of
thermostatic control so that the inside temperature
can never go beyond -18 °C, since temperature
higher than this can deteriorate frozen foods.
It is practical to make sure of faultless operation of
the appliance daily so as to notice possible failure
in time and prevent deterioration of frozen foods.
Hints and ideas
In this chapter practical hints and ideas are given
about how to use the appliance to reach maximum
energy saving and there is environmental information
about the appliance as well.
How to save energy
The colder the ambient temperature of the
appliance is the less energy it uses.
Avoid putting the appliance in a sunny place and
near anything that gives off heat.
Be sure that the condenser and the compressor
are well ventilated. Do not cover the sections where
ventilation is.
Wrap products in tightly closing dishes or cling film
to avoid building up unnecessary frost.
Avoid products put in the freezer compartment to
touch foods already frozen.
45
GB
Maintenance
Defrosting
Bleeding part of the moisture of cooling chamber in
form of frost and ice goes with the operation of the
appliance.
Thick frost and ice has an insulating effect, so it
reduces cooling efficiency as the temperature
increases and needs more energy.
After removing the freezing shelf it is possible to
scrape off and remove smaller frost and ice with the
enclosed ice scraper.
The tray in figure is not a piece of accessories to the
appliance!
When ice coating is so thick that it can not be removed
with the frost scraper defrosting is necessary. Its
frequency depends on usage.
How to defrost it:
4-5 hours before starting defrosting turn the
thermostatic control knob to "SUPER" position so that
the stored foods can refrigerate well.
Break the circuit of the appliance.
Take the frozen foods out of the appliance and put
them into a basket lined with paper or cloth. Store
them in a possibly cool place or replace them into a
frozen or fresh food compartment of a refrigerator.
Leave the door open.
Sweep off melting water, which gathers in the outlet
channel practically formed in the bottom of the
appliance, occasionally with a cloth or sponge in
direction of sides. It can be removed if you put an
adequately high tray in front of the appliance, which
defrost water will flow into.
Defrosting process can be made quicker by placing a
pot or dish filled with warm water to the freezing shelf.
After defrosting wipe the wet surfaces.
Apply voltage to the appliance.
Put the foods back.
Regular cleaning
It is practical to clean the inside of the freezer and
defrost it at a time.
Household cleaner or soap must not be used.
After breaking the circuit wash the appliance using
lukewarm water and wipe it.
Clean the door gasket with clean water.
After cleaning apply voltage to the appliance.
It is recommended to remove the dust and dirt
collected on the back of the appliance and the
condenser once or twice a year.
46
GB
When the refrigerator
is not in use
In case the appliance will not be used for a long time
follow these steps:
Break the circuit of the appliance.
Remove foods from the refrigerator.
Defrost and clean it as written before.
Leave the door open to avoid a build up of air inside.
Trouble shooting
During operation of the appliance some smaller but
annoying trouble can often occur, which does not
require calling a technician out. In the following chart
information is given about them to avoid unnecessary
charges on service.
We draw your attention that operation of appliance goes
with certain sounds (compressor- and circulating
sound). This is not trouble, but means normal
operation.
We draw it to your attention again that the
appliance operates discontinuously, so the
stopping of compressor does not mean being nocurrent. That is why you must not touch the electrical
parts of the appliance before breaking the circuit.
Problem
The appliance does not
cool sufficiently
Possible cause
Thermostatic control is set too low.
Before freezing the appliance was not pre-cooled
sufficiently.
Large-sized food was put in.
Too many foods to be frozen were put in.
Warm foods were put in.
Door is not shut properly.
Solution
Set higher position.
Pre-cool the appliance for enough time.
Cut up food.
Put fewer foods to be cooled.
Put foods max. at room temperature.
Check if the door is shut.
The appliance cools too
hard
The thermostatic control is set too high.
Set lower position.
The appliance does not
cool at all
Plug is not connected to the mains socket
properly.
There is no voltage in the mains socket.
Thermostatic control is in „STOP” position.
Check if the connection is proper.
The appliance is not supported properly.
Check if the appliance stands stable.
The appliance is noisy
Check if there is voltage.
Check setting of thermostatic control.
Inasmuch as the advice does not lead to result, call the nearest brand-mark service.
47
GB
Change of door opening direction
Should the setting-up or handling demand it, dooropening direction can be refitted from right-handed to
left-handed.
Following operations are to be done on the basis of
figures and explanations:
Break the circuit of the appliance.
Take the covering of top door holder off, unscrew
the screws fixing the top door holder (2 pieces) and
take it off according to figure.
Take the door off.
Unscrew the screws fixing the lower door holder
(2 pieces) and remove it according to figure.
Fix lower door holder on the other side.
Fit the door to the lower door holding pin.
To fit top door holder remove plastic coverings of
door holder holes carefully (e. g. with a knife) and
put them on the other side.
Fix top door holder with 2 screws in the place set
free being careful that the edge of the door is
parallel with the side of cupboard.
Put the covering of top door holder back.
Put over the handle and the plastic nails on the
other side.
In case you do not want to perform the procedures
above, call the nearest brand-mark service.
Technicians will accomplish the refitting expertly for
charge.
48
GB
Electrical connection
This refrigerator is designed to operate on a
230 V AC (~) 50 Hz supply.
The plug must be put into a socket with protective
contact. If there is no such, it is recommended to
get an electrician to fit an earthed socket in
compliance with standards near the refrigerator.
This appliance complies with the following
E.E.C. Directives:
73/23 EEC of 19.02.73 (Low Voltage Directive)
and subsequent modifications,
89/336 EEC
Compatibility
modifications.
of 03.05.89 (Electromagnetic
Directive)
and
subsequent
49
GB
War r ant y and ser vice
Guarantee conditions
Service and spare parts
If calling the service is unavoidable, announce the
trouble at a brand-mark service nearest to your place.
When announcing the appliance has to be identified
according to its data label.
The data label of the appliance is stuck to the wall of
the interior beside the vegetable box in the fresh food
compartment in the bottom on the left side. All
necessary data are there which are needed to the
service announcement (type, model, serial number,
etc.). Note here the data from the data label of your
appliance:
Model
Product No.
Serial No.
Date of purchase:
The manufacturer reserves the right to make any changes in the products.
50
51
Printed by Océ Hungária Kft.
2005. 09. 06.
Service-Hotline 0848 811 222
Service après-vente
Ch. Veyre-d’en-Haut
1806 St-Légier
Fax 021 652 37 88
Servicestelle Wangen
Postfach
4612, 4002 Wangen bei Olten
Telefon 062 206 33 55
Fax 062 206 33 12
*Tarif interurbain/Fernbereich/Area discosta
Info Service
Postfach 2550, 4002 Basel
Info - Tel. 0848 888 444*
www.coop.ch
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement