Aeg-Electrolux | S75328DT2 | User manual | Aeg-Electrolux S75328DT2 User Manual

SANTO 75328-2 DT
User manual
Fridge-Freezer
2
Contents
Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Safety information
Children and vulnerable people safety
General safety
Daily Use
Care and cleaning
Installation
Service
Control panel
Switching on
Switching off
Temperature regulation
Frostmatic function
First use
Cleaning the interior
Daily use
Movable shelves
Bottle rack
Positioning the door shelves
Cold Store compartment
Air cooling
Freezing Calendar
Freezing fresh food
Storage of frozen food
Thawing
Helpful hints and tips
2
3
3
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
7
7
8
8
8
8
9
Hints for energy saving
Hints for fresh food refrigeration
Hints for refrigeration
Hints for freezing
Hints for storage of frozen food
Care and cleaning
Periodic cleaning
Replacing the Taste Guard filter
Defrosting of the refrigerator
Defrosting of the freezer
Periods of non-operation
What to do if…
Replacing the lamp
Closing the door
Technical data
Installation
Positioning
Location
Electrical connection
Rear spacers
Installation of the Taste Guard Filter
Fitting the door handles
Removing the shelf holders
Door reversibility
Environmental concerns
9
9
9
9
10
10
10
10
11
12
12
12
14
14
14
14
15
15
15
16
16
16
17
17
19
Subject to change without notice
Safety information
In the interest of your safety and to ensure the correct use, before installing and first using
the appliance, read this user manual carefully, including its hints and warnings. To avoid
unnecessary mistakes and accidents, it is important to ensure that all people using the
appliance are thoroughly familiar with its operation and safety features. Save these in-
Safety information
3
structions and make sure that they remain with the appliance if it is moved or sold, so that
everyone using it through its life will be properly informed on appliance use and safety.
For the safety of life and property keep the precautions of these user's instructions as the
manufacturer is not responsible for damages caused by omission.
Children and vulnerable people safety
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Keep all packaging well away from children. There is risk of suffocation.
• If you are discarding the appliance pull the plug out of the socket, cut the connection
cable (as close to the appliance as you can) and remove the door to prevent playing
children to suffer electric shock or to close themselves into it.
• If this appliance featuring magnetic door seals is to replace an older appliance having a
spring lock (latch) on the door or lid, be sure to make that spring lock unusable before
you discard the old appliance. This will prevent it from becoming a death trap for a child.
General safety
CAUTION!
Keep ventilation openings clear of obstruction.
• The appliance is intended for keeping foodstuff and/or beverages in a normal household
as explained in this instruction booklet.
• Do not use a mechanical device or any artificial means to speed up the thawing process.
• Do not use other electrical appliances (such as ice cream makers) inside of refrigerating
appliances, unless they are approved for this purpose by the manufacturer.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
During transportation and installation of the appliance, be certain that none of the
components of the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition
– thoroughly ventilate the room in which the appliance is situated
4
Safety information
• It is dangerous to alter the specifications or modify this product in any way. Any damage
to the cord may cause a short-circuit, fire and/or electric shock.
WARNING!
Any electrical component (power cord, plug, compressor) must be replaced by a certified
service agent or qualified service personnel.
1. Power cord must not be lengthened.
2. Make sure that the power plug is not squashed or damaged by the back of the
appliance. A squashed or damaged power plug may overheat and cause a fire.
3. Make sure that you can come to the mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not insert the power plug. There is a risk of
electric shock or fire.
6. You must not operate the appliance without the lamp cover1) of interior lighting.
• This appliance is heavy. Care should be taken when moving it.
• Do not remove nor touch items from the freezer compartment if your hands are damp/
wet, as this could cause skin abrasions or frost/freezer burns.
• Avoid prolonged exposure of the appliance to direct sunlight.
Daily Use
•
•
•
•
•
Do not put hot pot on the plastic parts in the appliance.
Do not store flammable gas and liquid in the appliance, because they may explode.
Do not place food products directly against the air outlet on the rear wall.2)
Frozen food must not be re-frozen once it has been thawed out.
Store pre-packed frozen food in accordance with the frozen food manufacturer's instructions.
• Appliance's manufacturers storage recommendations should be strictly adhered to. Refer
to relevant instructions.
• Do not place carbonated or fizzy drinks in the freezer compartment as it creates pressure
on the container, which may cause it to explode, resulting in damage to the appliance.
• Ice lollies can cause frost burns if consumed straight from the appliance.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the mains plug from the
mains socket.
• Do not clean the appliance with metal objects.
• Do not use sharp objects to remove frost from the appliance. Use a plastic scraper.
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean
the drain. If the drain is blocked, water will collect in the bottom of the appliance.
Installation
For electrical connection carefully follow the instructions given in specific paragraphs.
1) If the lamp cover is foreseen
2) If the appliance is Frost Free
Control panel
5
• Unpack the appliance and check if there are damages on it. Do not connect the appliance
if it is damaged. Report possible damages immediately to the place you bought it. In that
case retain packing.
• It is advisable to wait at least four hours before connecting the appliance to allow the
oil to flow back in the compressor.
• Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.
• Wherever possible the back of the product should be against a wall to avoid touching
or catching warm parts (compressor, condenser) to prevent possible burn.
• The appliance must not be located close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.
• Connect to potable water supply only.3)
Service
• Any electrical work required to do the servicing of the appliance should be carried out
by a qualified electrician or competent person.
• This product must be serviced by an authorized Service Centre, and only genuine spare
parts must be used.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The appliance shall not be discarded together
with the urban refuse and rubbish. The insulation foam contains flammable gases: the
appliance shall be disposed according to the applicable regulations to obtain from your
local authorities. Avoid damaging the cooling unit, especially at the rear near the heat
exchanger. The materials used on this appliance marked by the symbol are recyclable.
Control panel
1
2
1 Temperature regulator
Frostmatic button
2 Frostmatic indicator
Switching on
Remove, if present, the remove label stuck on the inside of the freezer compartment.
Insert the plug into the wall socket.
Switching off
To switch off the appliance remove the mains plug.
3) If a water connection is foreseen
6
First use
Temperature regulation
The temperature is automatically regulated.
To operate the appliance, proceed as follows:
• press the temperature regulator more times until the LED corresponding to the required
temperature lights up. Selection is progressive, varying from +2°C to +8°C.
A medium setting is generally the most suitable.
However, the exact setting should be chosen keeping in mind that the temperature inside
the appliance depends on:
• room temperature
• how often the door is opened
• the quantity of food stored
• the location of the appliance.
If the ambient temperature is lower than 16°C press the temperature regulator until the
LED corresponding to the lowest temperature lights up.
Frostmatic function
You can activate the Frostmatic function by pressing the Frostmatic button more times
until the LED corresponding to the symbol Frostmatic indicator lights up.
To deactivate the Frostmatic function, press more times the Frostmatic button until the
required temperature is selected.
First use
Cleaning the interior
Before using the appliance for the first time, wash the interior and all internal accessories
with lukewarm water and some neutral soap so as to remove the typical smell of a brandnew product, then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
Daily use
7
Daily use
Movable shelves
The walls of the refrigerator are equipped with a
series of runners so that the shelves can be positioned as desired.
Bottle rack
Place the bottles (with the opening facing front)
in the pre-positioned shelf.
If the shelf is positioned horizontally, place only
closed bottles.
This bottle holder shelf can be tilted in order to
store previously opened bottles. To obtain this result, pull the shelf up so it can rotate upwards and
be placed on the next higher level.
Positioning the door shelves
To permit storage of food packages of various sizes, the door shelves can be placed at
different heights.
Cold Store compartment
The models equipped with this feature in the fridge part, it is indicated for a best conservation of fresh foods as fish, meat, seafood, etc.
It is placed in the lower part, directly above of the vegetable conservation drawer.
Air cooling
The Dynamic Air Cooling (DAC) fan let food cool quickly and a more uniform temperature
in the compartment.
8
Daily use
You can switch on the fan by pressing the switch
shown in the picture. The green light comes on.
Switch on the fan when the ambient temperature
exceeds 25°C.
B
Freezing Calendar
The symbols show different types of frozen goods.
The numbers indicate storage times in months for the appropriate types of frozen goods.
Whether the upper or lower value of the indicated storage time is valid depends on the
quality of the foods and treating before freezing.
Freezing fresh food
The freezer compartment is suitable for freezing fresh food and storing frozen and deepfrozen food for a long time.
To freeze fresh food activate the Frostmatic function at least 24 hours before placing the
food to be frozen in the freezer compartment.
Move the shelf present in the freezer compartment to the middle seat, keeping it horizontal.
Place the fresh food to be frozen on that shelf.
The maximum amount of food that can be frozen in 24 hours is specified on the rating
plate, a label located on the inside of the appliance.
The freezing process lasts 24 hours: during this period do not add other food to be frozen.
After 24 hours, when the freezing process is completed, return to the required temperature
(refer to "Temperature regulation").
Storage of frozen food
When first starting-up or after a period out of use, before putting the products in the
compartment let the appliance run at least 2 hours on the higher settings.
In the event of accidental defrosting, for example due to a power failure, if the power has
been off for longer than the value shown in the technical characteristics chart under "rising
time", the defrosted food must be consumed quickly or cooked immediately and then refrozen (after cooling).
Thawing
Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation.
Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking
will take longer.
Helpful hints and tips
9
Helpful hints and tips
Hints for energy saving
• Do not open the door frequently or leave it open longer than absolutely necessary.
• If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing
frost or ice on the evaporator. If this happens, set the Temperature Regulator toward
warmer settings to allow automatic defrosting and so a saving in electricity consumption.
Hints for fresh food refrigeration
To obtain the best performance:
• do not store warm food or evaporating liquids in the refrigerator
• do cover or wrap the food, particularly if it has a strong flavour
• position food so that air can circulate freely around it
Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable
drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s)
provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in
aluminium foil or polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
Hints for freezing
To help you make the most of the freezing process, here are some important hints:
• the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating
plate;
• the freezing process takes 24 hours. No further food to be frozen should be added during
this period;
• only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
• prepare food in small portions to enable it to be rapidly and completely frozen and to
make it possible subsequently to thaw only the quantity required;
• wrap up the food in aluminium foil or polythene and make sure that the packages are
airtight;
• do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding
a rise in temperature of the latter;
• lean foods store better and longer than fatty ones; salt reduces the storage life of food;
• water ices, if consumed immediately after removal from the freezer compartment, can
possibly cause the skin to be freeze burnt;
• it is advisable to show the freezing in date on each individual pack to enable you to keep
tab of the storage time.
10
Care and cleaning
Hints for storage of frozen food
To obtain the best performance from this appliance, you should:
• make sure that the commercially frozen foodstuffs were adequately stored by the retailer;
• be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the
shortest possible time;
• not open the door frequently or leave it open longer than absolutely necessary.
• Once defrosted, food deteriorates rapidly and cannot be refrozen.
• Do not exceed the storage period indicated by the food manufacturer.
Care and cleaning
CAUTION!
Unplug the appliance before carrying out any maintenance operation.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must
therefore only be carried out by authorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with lukewarm water and some neutral soap.
• regularly check the door seals and wipe clean to ensure they are clean and free from
debris.
• rinse and dry thoroughly.
Do not pull, move or damage any pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders, highly perfumed cleaning products or wax polishes
to clean the interior as this will damage the surface and leave a strong odour.
Clean the condenser (black grill) and the compressor at the back of the appliance with a
brush or a vacuum cleaner. This operation will improve the performance of the appliance
and save electricity consumption.
Take care of not to damage the cooling system.
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it is recommended that the outer casing of
this appliance is only cleaned with warm water with a little washing-up liquid added.
After cleaning, reconnect the equipment to the mains supply.
Replacing the Taste Guard filter
The Taste Guard filter helps to reduce the odours inside the fridge limiting the risk of
unwanted aroma in sensitive food
To get the best performance the Taste Guard filter should be changed once every year.
New active air filters can be purchased from your local dealer.
• The air filter is placed behind the flap and can be reached by pulling the flap outward
(1)
Care and cleaning
11
• pull out of the slot the exhausted air filter.
•
2
1
insert the new air filter in the slot (2)
• close the flap.
The air filter is a consumable accessory and as such is not covered by the guarantee.
During the operation, always keep the air ventilation flap closed.
The air filter should be handled carefully to prevent its surface from being scratched.
Defrosting of the refrigerator
Frost is automatically eliminated from the evaporator of the refrigerator compartment
every time the motor compressor stops, during normal use. The defrost water drains out
through a trough into a special container at the back of the appliance, over the motor
compressor, where it evaporates.
12
What to do if…
It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water overflowing and dripping onto the food inside. Use the
special cleaner provided, which you will find already inserted into the drain hole.
Defrosting of the freezer
The freezer compartment of this model, on the other hand, is a "no frost" type. This means
that there is no buildup of frost when it is in operation, neither on the internal walls nor
on the foods.
The absence of frost is due to the continuous circulation of cold air inside the compartment,
driven by an automatically controlled fan.
Periods of non-operation
When the appliance is not in use for long periods, take the following precautions:
• disconnect the appliance from electricity supply
• remove all food
• defrost 4)and clean the appliance and all accessories
• leave the door/doors ajar to prevent unpleasant smells.
If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food
inside from spoiling in case of a power failure.
What to do if…
WARNING!
Before troubleshooting, disconnect the mains plug from the mains socket.
Only a qualified electrician or competent person must do the troubleshooting that is not
in this manual.
There are some sounds during normal use (compressor, refrigerant circulation).
Problem
The appliance does not
operate. The lamp does
not operate.
4) If foreseen.
Possible cause
The appliance is switched off.
Solution
Switch on the appliance.
What to do if…
Problem
Possible cause
13
Solution
The mains plug is not connected Connect the mains plug to the
to the mains socket correctly.
mains socket correctly.
The appliance has no power.
Connect a different electrical apThere is no voltage in the mains pliance to the mains socket.
socket.
Contact a qualified electrician.
The lamp does not work.
The compressor operates
continually.
The lamp is in stand-by.
Close and open the door.
The lamp is defective.
Refer to "Replacing the lamp".
The temperature is not set correctly.
Set a higher temperature.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too
frequently.
Do not keep the door open longer
than necessary.
The product temperature is too
high.
Let the product temperature decrease to room temperature before storage.
The room temperature is too
high.
Decrease the room temperature.
Water flows on the rear
plate of the refrigerator.
During the automatic defrosting This is correct.
process, frost defrosts on the
rear plate.
Water flows into the refrigerator.
The water outlet is clogged.
Clean the water outlet.
Products prevent that water
flows into the water collector.
Make sure that products do not
touch the rear plate.
Water flows on the
ground.
The melting water outlet does
Attach the melting water outlet
not flow in the evaporative tray to the evaporative tray.
above the compressor.
The temperature in the
appliance is too low.
The temperature regulator is not Set a higher temperature.
set correctly.
The temperature in the
appliance is too high.
The temperature regulator is not Set a lower temperature.
set correctly.
The door is not closed correctly. Refer to "Closing the door".
The product temperature is too
high.
Let the product temperature decrease to room temperature before storage.
Many products are stored at the Store less products at the same
same time.
time.
The temperature in the
refrigerator is too high.
There is no cold air circulation in Make sure that there is cold air
the appliance.
circulation in the appliance.
The temperature in the
freezer is too high.
Products are too near to each
other.
Store products so that there is
cold air circulation.
14
Technical data
Problem
There is too much frost.
Possible cause
Food is not wrapped correctly.
Solution
Wrap the food correctly.
The door is not closed correctly. Refer to "Closing the door".
The temperature regulator is not Set a higher temperature.
set correctly.
Replacing the lamp
CAUTION!
Disconnect the plug from the mains socket.
1. Press on the rear hook of the lamp cover by a
screwdriver and at the same time pull and ro1
tate the cover in the direction of the arrow.
2. Replace the lamp with one of the same power
(the maximum power is shown on the light
bulb cover).
3. Install the lamp cover by fixing it into its original position.
4. Connect the plug to the mains socket.
5. Open the door. Make sure that the light comes on.
2
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to "Installation".
3. If necessary, replace the defective door gaskets. Contact the Service Center.
Technical data
Dimension of the recess
Rising Time
Height
1750 mm
Width
600 mm
Depth
645 mm
20 h
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
Installation
WARNING!
Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
Installation
15
Positioning
Install this appliance at a location where the ambient temperature corresponds to the
climate class indicated on the rating plate of the appliance:
Climate class
Ambient temperature
SN
+10°C to + 32°C
N
+16°C to + 32°C
ST
+16°C to + 38°C
T
+16°C to + 43°C
Location
The appliance should be installed well away from sources of heat such as radiators, boilers,
direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet. To
ensure best performance, if the appliance is positioned below an overhanging wall unit,
the minimum distance between the top of the cabinet and the wall unit must be at least
100 mm . Ideally, however, the appliance should not be positioned below overhanging wall
units. Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet.
A
B
10 mm
10 mm
100 mm
WARNING!
It must be possible to disconnect the appliance from the mains power supply; the plug
must therefore be easily accessible after installation.
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply.
The appliance must be earthed. The power supply cable plug is provided with a contact for
this purpose. If the domestic power supply socket is not earthed, connect the appliance to
a separate earth in compliance with current regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if the above safety precautions are not observed.
16
Installation
This appliance complies with the E.E.C. Directives.
Rear spacers
Inside the appliance you find two spacers
which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then retighten the screws.
Installation of the Taste Guard Filter
The Taste Guard Filter is an active carbon filter which absorbs bad odours and permits to
maintain the best flavour and aroma for all foodstuffs without risk of odour cross contamination.
On delivery the carbon filter is in a plastic bag to maintain it’s duration and characteristics.
The filter should be placed behind the flap before the appliance is turned on.
1. Pull the flap outwards (1)
2. Remove the filter from the plastic bag
3. Insert the filter in the slot found in the
back of the flap cover (2)
4. Close the flap cover
During operation, always keep the air ventilation flap closed.
The filter should be handled carefully so fragments do not loosen from the surface.
Fitting the door handles
The handles are supplied as a kit at delivery.
2
1
Installation
1. Screw the top handle bracket to the handle rod.
2. Fit the bottom handle bracket on the lower right-hand side of the door.
3. Fit the top handle bracket on the top
right-hand side of the door.
4. Screw the handle rod to the bottom handle bracket.
1
2
3
4
17
Do not use excessive force and overtighten the
screws (max. 2 Nm) as you may damage the
door handles.
Removing the shelf holders
Your appliance is equipped with shelf retainers
that make it possible to secure the shelves during
transportation.
To remove them proceed as follows:
1. Move the shelf holders in the direction of the
arrow (A).
2. Raise the shelf from the rear and push it forward until it is freed (B).
3. Remove the retainers (C).
A
B
C
Door reversibility
WARNING!
Before carrying out any operations, remove the mains plug from the power socket.
To carry out the following operations, we suggest that this be made with another person
that will keep a firm hold on the doors of the appliance during the operations.
To change the opening direction of the door, do these steps:
18
Installation
1.
2.
3.
4.
Slide the bottom door off the middle
hinge (H). Remove the middle hinge by
unscrewing the fixing screws.
Make sure to remove the plastic spacer
inserted under the hinge.
H
Slide the top door off the pin (G). Unscrew the pin (G) and install it on the
opposite side.
Remove the two plugs from the middle
crossbeam and install them on the opposite side, covering the holes left free
from the removed hinge.
Remove the plugs (1) on the upper side
of both doors and move them to the
other side.
G
1
19
Environmental concerns
5.
6.
Remove with a tool the cover (e), unscrew the lower hinge pivot (f) using a
10 mm spanner and re-screw it on the
opposite side.
Install the cover (e) on the opposite side.
e
2
1
5
f
4
7.
Remove the handle. Unscrew the top
handle bracket from the handle rod (h1).
Unscrew the bottom handle bracket
from the door (h2). Unscrew the top
handle bracket from the door (h3).
Install the plug (1).
h1
3
h2
h3
8.
Install the handle in the opposite side.
h4
h5
h6
Re-screw the handle bracket on the door
(h4). Turn the handle bracket with the
handle and screw them to the door (h5)
and the fitted handle bracket (h6).
9. Install the top door on the pin (G). Insert
the pivot of the middle hinge (H) into the
hole of the top door. Make sure that the
plastic space is placed under the hinge. Install the bottom door on the lower hinge
pivot (f). Slightly tilting the doors insert the pivot of the middle hinge (H) into the hole
of the bottom door.
10. Keeping the doors open, tighten the middle hinge with two screws.
11. Make sure that the front board of the door is parallel to the front board of the top.
12. Reposition, level the appliance, wait for at least four hours and then connect it to the
power socket.
Do a final check to make sure that:
• All screws are tightened.
• The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting of the gasket.
Environmental concerns
The symbol
on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
20
for the recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product, please contact
your local council, your household waste disposal service or the shop where you purchased
the product.
21
22
23
212710232-00-16072009
www.electrolux.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising