Aeg S1544-7TK User Manual

Add to My manuals
24 Pages

advertisement

Aeg S1544-7TK User Manual | Manualzz
SANTO
Tisch-Kühlautomat
Réfrigérateur automatique
table top
Automatic Refrigerator
Gebrauchsanweisung
Mode d’emploi
Operating Instructions
Dear customer,
☞
Before placing your new refrigerator/freezer into operation please read
these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance.
Please keep these operating instructions for future reference. Pass
them on to possible new owners of the appliance.
These operating instructions are for use with several technically
comparable models with varying accessories. Please observe the notes
which apply to your model.
Notes which are important for your safety or for the proper functioning of the appliance are stressed with a warning triangle and/ or with
signal words (Warning!, Caution!, Attention!). Please observe the following carefully.
This symbol guides you step by step in the operation of the appliance.
Supplementary information regarding operation and practical applications of the appliance appear after this symbol.
Tips and notes concerning economical and environmentally sound use
of the appliance are marked with the cloverleaf.
The operating instructions contain instructions for the correction of
possible malfunctions by the user in the section "What to do if ...". If
these instructions should not be sufficient, our customer service
department is always available to you.
Printed on paper manufactured with environmentally sound processes.
he who thinks ecologically acts accordingly ...
42
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Your refrigerator needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Detaching the worktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Mounting under a continuous worktop . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Reversing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Prior to Initial Start–Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
View of the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Starting up and temperature regulation . . . . . . . . . . . . . . . . . . . . . . . . . 52
Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Storage shelves/wire trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Variable door interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
VARIO glass storage shelf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Correct storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
The fridge defrosts automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Switching off the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Energy Saving Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Changing the light bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Noises during Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
43
Safety
The safety aspects of our refrigerators/freezers comply with accepted technical standards and the German Appliance Safety Law.
Nevertheless, we consider it our obligation to make you aware of
the following safety information:
Intended use
• The refrigerator is intended for use in the home. It is suitable for the
storing of food at low temperature. If the appliance is used for purposes other than those intended or used incorrectly, no liability can
be accepted by the manufacturer for any damage that may be
caused.
• Alterations or changes to the refrigerator are not permitted for reasons of safety.
• If you use the refrigerator in a commercial application or for purposes other than the cooling of foods, the manufacturer accepts no liability for any damages which may occur.
Prior to initial start–up
• Ensure that the appliance does not stand on the electrical supply
cable. Important: if the supply cable is damaged, it must be replaced
by authorised service or qualified personnel using a special cable of
the same type.
• Check the appliance for transport damage. Under no circumstance
should a damaged appliance be plugged in. In the event of damage,
please contact your supplier.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant
circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain
that none of the components of the refrigerant circuit become damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
Safety of children
• Packaging (e.g. wraps, polystyrene) can be dangerous for children.
There is a risk of suffocation! Keep packaging material away from
children!
44
• Please make old appliances unusable prior to disposal. Pull out the
mains plug, cut off the mains cable, break or remove spring or bolt
catches, if fitted. By doing this you ensure that children cannot lock
themselves in the appliance when playing (there is risk of suffocation!) or get themselves into other dangerous situations.
• Often children cannot recognise the hazards present in household
appliances. It is therefore important that you ensure adequate supervision and never let children play with the appliance!
Daily Operation
• Containers with flammable gases or liquids can leak at low temperatures. There is a risk of an explosion! Do not store any containers
with flammable materials such as spray cans, fire extinguisher refill
cartridges etc in the refrigerator and/or freezer.
• Do not operate any electrical appliances in the refrigerator and/or
freezer (e.g. electric ice cream makers, mixers etc.).
• Before cleaning the appliance, always switch off the appliance and
unplug it, or pull the house fuse or switch off the circuit breaker.
• When unplugging always pull the plug from the mains socket, do not
pull on the cable.
In case of malfunction
• If a malfunction occurs on the appliance, please look first in the
"What to do if ..." section of these instructions. If the information
given there does not help, please do not perform any further repairs
yourself.
• Under no circumstances should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact our Customer Service.
45
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be disposed of or
burned at an incinerating plant without danger.
About the materials: The plastics can be recycled and are identified as
follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the
interior.
>PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
The carton parts are made from recycled paper and should be disposed
of at a waste-paper recycling collection location.
Disposal of old Appliances
For environmental reasons, refrigeration appliances must be disposed
of properly. This applies to your old appliance, and - at the end of its
service life - for your new appliance as well.
Warning! Before disposing of old appliances make them inoperable.
Remove plug from mains, sever the power cable, remove or destroy
any snap or latch closures. This ensures that playing children do not
lock themselves inside the appliance (danger of suffocation!) or place
themselves into other life-endangering situations.
Disposal:
• The appliance may not be disposed of with domestic waste or bulky
refuse.
• The refrigerant circuit, especially the heat exchanger at the back of
the appliance, must not be damaged.
• Information concerning collection schedules or locations can be
obtained from your local Council or Environmental Health Office.
Remove transport packaging
☞
The appliance and the interior fittings are protected for transport.
Pull off the adhesive tape on the left and right side of the door.
You can remove any remnants of adhesive using white spirit.
☞
46
Remove all adhesive tape and packing pieces from the interior of the
appliance.
Installation
Installation Location
The appliance should be set up in a well ventilated, dry room.
Energy use and efficient performance of the appliance is affected by
the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature
corresponds to the climate classification, for which the appliance is
designed.
The climate classification can be found on the serial plate, which is
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for
each climate classification:
Climate classification
for an ambient temperature of
SN
+10 to +32 °C
N
+16 to +32 °C
ST
+18 to +38 °C
T
+18 to +43 °C
If the refrigeration appliance is installed next to another refrigerator
or freezer a clearance of 5 cm at the sides is required, in order to prevent the formation of condensation on the outside of the appliance.
Your refrigerator needs air
For correct operation this appliance must be located in a dry atmosphere, away from heat sources, e.g. cookers, radiators, boilers and
direct sunlight.
You should also ensure that air can circulate freely around the back
and the top of the cabinet. There should be 100mm (4”) between the
top of the cabinet and any overhanging kitchen furniture.
Alternatively allow 50mm (2”) between the top of the cabinet and any
overhanging kitchen furniture and a gap of 25mm (1”) on either side
of the appliance.
47
If your refrigerator is installed under
a continuous worktop, an air outlet
opening of at least 200 cm2 and a
ventilation grille (A/B) matching the
worktop design should be provided
at the rear of the worktop.
The cut surfaces of the worktop (C)
should be varnished to avoid swelling
due to penetration of moisture.
The appliance wall distance must be
at least 30 mm and should be
checked before the ventilation grille
is inserted.
Special accessories:
A Ventilation grille, brown
B Ventilation grille, white
A/B
200 cm2
105
C
570
550
93-103
AEG36
Detaching the worktop
After the worktop has been removed the appliance can be installed
underneath a continuous worktop.
The procedure is as follows:
☞
☞
Unscrew the Philips screws (F) on the
right and the left.
Lift the worktop slightly, push it
about 20 mm towards the rear, and
lift it off upwards (G).
Unscrew the holding bracket (H) and
keep it in a safe place.
F
G
H
G 56/1
Mounting under a continuous
worktop
If installed under a continuous
worktop, the appliance is fastened
with a mounting screw (A) under the
panel.
48
A
AEG96
Reversing the door
The side at which the door opens can be changed from the right side
(as supplied) to the left side, if the installation site requires.
Warning! When changing the side at which the door opens, the appliance must not be connected to the mains. Remove plug from the
mains beforehand.
☞
☞
☞
Tilt the appliance slightly towards the
rear and prop it securely.
Unscrew the door hinge screws (K)
and remove the hinge pin bracket (1).
Open the door a little way and take it
out downwards.
1
K
AEG97
☞
☞
☞
Unscrew the upper pin (A) and screw
it into place on the opposite side.
Fit the door into the upper pin (A)
and close it.
Screw the hinge pin bracket (1)
securely into place on the opposite
side using the screws (K).
A
12
AEG98
☞
Unscrew the handle. Refit it on the
opposite side after having pushed in
the plugs with a punch. Cover the
holes left open with the plugs contained in the documentation pack.
49
Prior to Initial Start–Up
☞
Please clean the appliance interior and all accessories prior to initial
start-up (see section: “Cleaning and Care”).
Electrical Connection
The plug socket necessary for connection of your appliance to the
electricity supply should be positioned so that it is possible to pull out
the appliance plug.
If your appliance is installed under a
continuous worktop, the plug socket
should be provided as shown.
Alternatively a concealed spur socket
130
fitted with a 13 A fuse may be fitted.
If the socket is not accessible once
the appliance is built in, the electri300
cal installation must include suitable
means of isolating the appliance
from the mains (e.g. fuse, cut-out,
current trip or similar with a minimum contact separation of 3 mm).
AEG44
☞
50
Before initial start-up, refer to the appliance serial plate to ascertain if
supply voltage and current values correspond with those of the mains
at the installation location.
e.g.: AC 220 ... 240 V
50 Hz or
220 ... 240 V
~50 Hz
(i.e. 220 to 240 volts alternating current, 50 Hertz).
The rating plate is inside the appliance on the left.
Description of the appliance
View of the appliance
➆
➅
➀
➁
➂
➇
➀
➁
➂
➃
➄
➅
➆
➇
➄
➃
Butter/cheese compartments with flap and egg storage insert
Door storage compartment with retaining rail (not for all models)
Door storage compartment
Bottle shelf
Vegetable drawer
Storage shelves
Temperature regulator and light switch
Rating plate
51
Starting up and temperature regulation
☞
Insert the plug of the connection lead into the plug socket with protective earth contact.
When the refrigerator compartment door is opened, the internal lighting is switched on.
The temperature selector knob is
located on the RH side of the refrigerator compartment.
Setting “0” means: Off.
Turning clockwise in direction “1”:
Refrigerating unit on, the latter then
operating automatically.
Setting “1” means:
Hightest temperature, warmest setting.
Setting “6” (end-stop) means:
Lowest temperature, coldest setting.
AEG62
At a low ambient temperature of around 16°C, setting “1” should be
selected. At ambient temperatures of around 25°C, select setting “2”. If
you require a lower temperature, select setting “3” or “4”.
Important!
High ambient temperatures (e.g. on hot summer days) and a cold setting on the temperature regulator (position”5” to “6”) can cause the
compressor to run continuously.
Reason: when the ambient temperature is high, the compressor must
run continuously to maintain the low temperature in the appliance.
The fridge will not be able to defrost since automatic defrosting of the
fridge is only possible when the compressor is not running (see also
"Defrosting" section). The result is the build up of a thick layer of frost
on the fridge rear wall.
If this happens, turn the temperature regulator back to a warmer setting (position “3” to “4”). At this setting the compressor will be
switched on and off as usual and automatic defrosting recommenced.
52
Interior Accessories
Storage shelves/wire trays
☞
☞
☞
Various glass or plastic storage shelves and wire trays are included with
your appliance - different models have different combinations.
You should always slide one of the full size glass storage shelf into the
lowest set of guides, above the fruit and the vegetable containers, and
keep it in this position.
The height of the storage shelves can be adjusted:
To do this pull the storage shelf forward until it can be swivelled
upwards or downwards and removed.
Please do the same in reverse to insert the shelf at a different height.
Variable door interior
Depending on your requirements, the storage compartments on the
door can be removed and repositioned in a different place.
VARIO glass storage shelf
☞
Your appliance is equipped with two half size glass storage shelves.
Storing tall items:
Slide the front half of the Vario storage
shelf in another level to the rear. By
this means you will gain space to place
tall items on the storage shelf below.
53
Correct storage
➀ Butter and cheese
➁ Eggs and preserves
➂ Drinks
➃ Cheese storage, fruit, and
vegetables
➄ Meat, salami, cold cuts, dairy
produce
➅ Ready meals, pastries, preserves
➅
➅
➄
➄
➃
➀
➁
➁
➂
The length of storage time depends on the type of food - see manufacturer’s instructions.
For physical reasons, there are different temperature regions in the
fridge. The coldest regio is on the lowest storage shelf. Warmer regions
are the top storage shelf, the vegetable basket and the storage compartments on the door.
Tip: Food in the fridge should always be covered or packaged, to prevent drying and tainting of other food.
The following are suited for packaging:
– Polyethylene airtight bags and wraps;
– Plastic containers with lids;
– Special plastic covers with elastic;
– aluminium foil.
Defrosting
The fridge defrosts automatically
The rear wall of the fridge covers with frost when the compressor is
running, and defrosts when the compressor is off. The water from the
thawing frost evaporates by itself.
54
Switching off the appliance
☞
☞
☞
☞
☞
☞
To switch off the appliance, turn the temperature regulator to position
"0".
If the appliance is not going to be used for an extended period:
Remove all refrigerated packages.
Switch off the appliance by turning the thermostat knob to position
"0".
Remove the mains plug or switch off or disconnect from the electricity
supply.
Clean thoroughly (see section: “Cleaning and Care”).
Leave the door open to avoid the build up of odours.
Cleaning and Care
For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.
☞
☞
Warning!
• The appliance may not be connected to the mains during cleaning.
Danger of electrical shock! Before cleaning switch the appliance off
and remove the plug from the mains, or switch off or turn out the
circuit breaker or fuse.
• Never clean the appliance with a steam cleaner. Moisture could
accumulate in electrical components, danger of electrical shock! Hot
vapours can lead to the damage of plastic parts.
• The appliance must be dry before it is placed back into service.
Important!
• Ethereal oils and organic solvents can attack plastic parts, e.g.
– lemon juice or the juice from orange peel;
– butyric acid;
– cleansers which contain acetic acid.
Do not allow such substances to come into contact with appliance
parts.
• Do not use any abrasive cleansers.
Remove the food from the refrigerator. Store it in a cool place, well
covered.
Switch the appliance off and remove the plug from the mains, or
switch off or turn out the circuit breaker or fuse.
55
☞
☞
☞
☞
Clean the appliance and the interior accessories with a cloth and lukewarm water. Commercially available dish washing detergents may also
be used.
After cleaning wipe with fresh water and rub dry.
Accumulation of dust at the condenser increases energy consumption.
For this reason carefully clean the condenser at the back of the appliance once a year with a soft brush or a vacuum cleaner.
Check the water drain hole on the rear
wall of the fridge.
Clear a blocked drain hole with the aid
of the green peg in the pack of accessories included with the appliance.
After everything is dry place appliance back into service.
Energy Saving Tips
• Do not install the appliance near cookers, radiators or other sources
of warmth. High ambient temperatures cause longer, more frequent
operation of the compressor.
• Ensure sufficient air circulation and exhaust at the appliance base
and at the back wall of the appliance. Never cover air vent openings.
• Do not place warm foods into the appliance. Allow warm foods to
cool first.
• Only leave door open as long as necessary.
• Do not set temperature any colder than necessary.
• Always keep the heat emitting condenser, the metal grille on the rear
wall of your appliance clean.
56
What to do if ...
Correcting Malfunctions
Spare parts:
The following spare parts can be ordered from our local Customer
Service. You can fit these yourself without any special skill or training,
e.g.:
– butter/cheese compartment,
– egg holders,
– door racks,
– fruit and vegetable drawers,
– storage racks
A malfunction may be caused by only a minor fault that you can rectify yourself using the following instructions. Do not perform any other
work on the appliance if the following information does not provide
assistance in your specific case.
Important! Repairs to refrigerators/freezers may only be performed by
competent service engineers. Improper repairs can give rise to
significant hazards for the user. If your appliance needs repairing,
please contact your specialist dealer or our local Customer Service.
Symptom
Appliance does not work.
Possible Cause
Appliance is not switched
on.
Mains plug is not plugged
in or is loose.
Fuse has blown or is
defective
Socket is defective.
Appliance cools too much.
Temperature is set too
cold.
Remedy
Switch on the appliance.
Insert mains plug.
Check fuse, replace if necessary.
Mains malfunctions are to
be corrected by an
electrician.
Turn the temperature regulator to a warmer
setting temporarily.
57
Symptom
The food is too warm.
Interior lighting does not
work.
Heavy build up of frost,
possibly also on the door
seal.
Unusual noises.
The compressor does not
start immediately after
changing the temperature
setting.
Water on the floor or on
storage shelves.
58
Possible Cause
Temperature is not
properly adjusted.
Door was open for an
extended period.
A large quantity of warm
food was placed in the
appliance within the last
24 hours.
The appliance is near a
heat source.
Remedy
Please look in the “Initial
Start Up” section.
Open the door only as long
as necessary.
Turn the temperature regulation to a colder setting
temporarily.
Please look in the
“Installation location” section.
Light bulb is defective.
Please look in the “Changing
the Light Bulb” sections.
Door seal is not air tight
(possibly after reversing
the door).
Carefully warm the leaking
sections of the door seal
with a hair dryer (on a
cool setting). At the same
time shape the warmed
door seal by hand such
that it sits correctly.
Appliance is not level.
Readjust the feet.
The appliance is touching
the wall or other objects.
Move the appliance
slightly.
A component, e.g. a pipe,
If necessary, carefully bend
on the rear of the appliance
the component out of the
is touching another part of
way.
the appliance or the wall.
This normal, no error has
occurred.
The compressor starts after
a period of time.
Water drain hole is
blocked.
See the “Cleaning and
Care” section.
Changing the light bulb
☞
☞
☞
☞
☞
☞
☞
Warning! There is a risk of electric shocks! Before changing the light
bulb, switch off the appliance and unplug it, or pull the fuse or the
circuit breaker.
Light bulb data: 220-240 V, max. 15 W
To switch off the appliance, turn the temperature regulator to position
"0".
Unplug the mains plug.
To change the light bulb, undo the
screw.
Press the light bulb cover as shown
and slide it backwards.
Change the defective light bulb.
Refit the light bulb cover and the
screw.
Put the refrigerator back into operation.
AEG65
Customer Service
If you cannot find the remedy for a malfunction in these operating
instructions, please contact your dealer or our customer service
department. Addresses and telephone numbers are listed in the accompanying booklet "Guarantee Conditions/Customer Service Locations".
Selective ordering of replacement parts can save unnecessary travel
and costs. For this reason always provide the following appliance
information:
• Model Name
• Model Number (PNC)
• Serial Number (S-No.)
This information can be found on the serial plate in the interior at the
left of the appliance. We recommend that you enter this information
here, so that it is handy if needed.
Note: The customer bears the costs of unjustified customer service
calls even during the guarantee period.
59
Noises during Operation
The following noises are characteristic of refrigeration appliances:
Whenever the compressor switches on or off, a click can
• Clicks
be heard.
• Humming As soon as the compressor is in operation, you can hear
it humming.
• Bubbling/ When refrigerant flows into thin tubes, you can hear
Splashing bubbling or splashing noises. Even after the compressor
has been switched off, this noise can be heard for a
short time.
Regulations, Standards, Guidelines
This appliance was designed for household use and was manufactured
in accordance with the appropriate standards. The necessary measures
in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and
the regulations of the German Society of Electrical Engineers (VDE)
were observed in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks.
This appliance is in accordance with the following EU
guidelines:
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.
– 89/336/EWG dated 3 May 1989
(including guideline change notice 92/31/EWG) - EMV guideline
60
Technical terminology
• Refrigerant
Liquids that can be used to a generate a cooling
effect are known as refrigerants. They have a relatively low boiling-point, indeed so low, that the
warmth from the food stored in the fridge or freezer
can cause the refrigerant to boil and vaporise.
• Refrigerant
Circuit
Closed circulation system that contains the refrigerant. The refrigerant circuit comprises primarily of an
evaporator, a compressor, a condenser and pipe
work.
• Evaporator
The refrigerant is evaporated in the evaporator.
Similar to all other liquids, refrigerant requires heat
to evaporate. This heat is removed from the interior
of the appliance, as a result the interior is cooled.
The evaporator is therefore located inside the appliance or placed in foam immediately behind the
inner wall and thus not visible.
• Compressor
The compressor looks like a small drum. It is driven
by a built-in electric motor and is mounted on the
base of the appliance at the rear. The task of the
compressor is to draw in vaporised refrigerant from
the evaporator, to compress it, and to pass it on to
the condenser.
• Condenser
The condenser normally has the form of a grid. The
refrigerant compressed in the compressor is liquefied
in the condenser. During this process, heat is
released to the surrounding air at the surface of the
condenser. The condenser is mounted on the base of
the appliance.
61
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
02-0701
2222 618-23

advertisement

Related manuals

advertisement