advertisement
▼
Scroll to page 2
of 10
FRIGORIFEROCONGELATORE FRIDGE-FREEZER KÜHLGEFRIERSCHRANK ZR 220/100 N LIBRETTO ISTRUZIONI 2222 124-84 INSTRUCTION BOOKLET GEBRAUCHSANWEISUNG CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 11 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12 Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12 Cleaning the interior . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12 Building-in instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12 Door reversibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12 Use . Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 15 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 15 Temperature regulation . . . . . . . . . . . . . . . . . . . . . . . . . . .page 15 Fresh food refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . .page 15 Movable shelves . . . . . . . . . . . . . . . . . . . . . . . . . .page 15 Positioning the door shelves . . . . . . . . . . . . . . . . . . . . . . . . .page 15 Freezing fresh food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 16 Storage of frozen food . . . . . . . . . . . . . . . . . . . . . . . . . . .page 16 Thawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 16 Ice-cube production . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 16 Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 17 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 18 Periodic cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 18 Periods of non-operation. . . . . . . . . . . . . . . . . . . . . . . . . . .page 18 Interior light. . . . . . . . . . . . . . . . . . . . . . . . . . .page 18 Customer Service and spare parts . . . . . . . . . . . . . . . . . . . . . . . . .page 18 10 . . . . . . . WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. ª This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product. ª Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. ª This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used. ª It is dangerous to alter the specifications or modify this product in any way. ª Care must be taken to ensure that the appliance does not stand on the electrical supply cable. ª The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. ª Frozen food must not be re-frozen once it has been thawed out. ª The inner lining of the appliance consists of channels through which the refrigerant passes. If these should be punctured this would damage the appliance beyond repair and cause food loss. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Frost may be removed by using the scraper provided. Under no circumstances should solid ice be forced off the liner. Solid ice should be allowed to thaw when defrosting the appliance. See defrost instructions. ª Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. ª This appliance is heavy. Care should be taken when moving it. ª Ice lollies can cause frost burns if consumed straight from the appliance. ª Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local Service Centre, and always insist on genuine spare parts. ª This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials; it must nevertheless be disposed of in a proper manner, in accordance with regulations for protection of the environment. ª Manufacturers’ storage recommendations should be strictly adhered to. Refer to relevant instructions. ª There are working parts in this product which heat up. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. See installation instructions. ª Parts which heat up should not be exposed. Wherever possible the back of the product should be against a wall. ª Before any cleaning or maintenance work is carried out, be sure to switch off and unplug the appliance. ª If the appliance has been transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor. 11 INSTALLATION If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special “Building-in” instructions given. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E.E.C. Directives: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. Building-in instructions P P A P1 P1 D114 Fig. 1 Door reversibility Right opening Remove pins (P) and (P1). 12 Left opening Remove (P) from both sides and also remove the door. Remove centre hinge (A) and refit it on the opposite side. Refit the door and (P) on the left-hand side and remove (P1) from the right-hand side. Housing dimensions Height Depth Width 1780 mm 550 mm 560 mm To ensure adequate ventilation, allow the clearances shown in figure 2. Fig. 2 50-min. cm2 200 Fig. 5 Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance D hinges. Fasten the appliance with 4 C D092 screws provided in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position. min. 2 cm Fig. 6 Press in the joint covers between the appliance and the kitchen unit. 200 D027 A Fig. 3 Push appliance into the housing until stop strip (A) touches the kitchen unit. D098 Fig. 7 Apply covers (B) on joint cover lugs and into hinge holes. D023 Fig. 4 If after having carried out the previously A described operation there is still some space left between the appliance and the kitchen unit, fit the trimming D265 provided together with the appliance on the stop strip (A). B D096 13 Fig. 8 Position the runners (E) at E the top and bottom of the inside of the kitchen unit as shown in Fig. 8 20m m and mark the position of the external holes. D285 After preparing the holes, screw the runners to the kitchen unit door using 3.5x16 mm screws. 8mm PR34 Fig. 9 Open both the appliance door and that of the kitchen unit to approx. 90°. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. Fig. 10 Remove the little plates and make the holes with a diam. of 2 mm. Replace the little plates over the runners and screw in the screws provided (3.5x16 mm). PR35 For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. 14 G H D291 Fig. 11 If the appliance is fixed to the side of the kitchen unit, simply slacken the screws in fixing brackets (G), move the brackets as shown in the figure and retighten the screws. Then fit cover (H). USE Operation Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, clockwise, beyond the «O» (STOP) position. The appliance will start to operate. Temperature regulation The temperature is automatically regulated and can be increased to achieve a higher temperature (warmer) by rotating the thermostat knob toward lower settings or reduced (colder) rotating the knob towards higher settings. However, the exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on: room temperature; how often the door is opened; the quantity of food stored; location of appliance. A medium setting is generally the most suitable. To stop operation, simply turn the thermostat knob to position «O». Important If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption. Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator. Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. Fig. 12 D040 Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be adjusted in height. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required (Fig. 13). Fig. 13 Fresh food refrigeration To obtain the best performance: do not store warm food or evaporating liquids in the refrigerator; do cover or wrap the food, particularly if it has a strong flavour. Position food so that air can circulate freely round it. Useful hints: Meat (all types): wrap in polythene bags and place on the glass shelf above the vegetable drawer. For safety, store in this way only one or two days at the most. Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf. Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided. Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible. Milk bottles: these should have a cap and should be stored in the bottle rack on the door. D009 For more thorough cleaning, the top door shelf can be removed by pulling it in the direction of the arrows, then refitting it in position (Fig. 14). Fig. 14 D064 15 Freezing fresh food Storage of frozen food The 4-star compartment ( ) is suitable for long term storage of commercially frozen food and for freezing fresh food. To freeze fresh foods it is not necessary to change the setting of the thermostat knob. However, for a quicker freezing operation, turn the thermostat knob to the coldest setting; but remember that, in this condition, the refrigerator compartment temperature might drop below 0°C. If this occurs reset thermostat knob to a warmer setting. Place the food to be frozen in the upper compartment of the freezer as this is the coldest part. To help you make the most of the freezing process, here are some important hints: the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate; the freezing process takes 24 hours. No further food to be frozen should be added during this period; only freeze top quality, fresh and thoroughly cleaned, foodstuffs; prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required; wrap up the food in aluminium foil or polythene and make sure that the packages are airtight; do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter; lean foods store better and longer than fatty ones; salt reduces the storage life of food; water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt; it is advisable to show the freezing-in date on each individual pack to enable you to keep tab of the storage time; on the inner door or special card (if supplied) you will find sketches of various animals and food types together with the recommended storage time (in months) from the time of freezing; do not put carbonated liquids (fizzy drinks, etc.) in the freezing compartment as they may burst. When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run for at least two hours on the coldest setting, then turn the thermostat knob to the normal operating position. To obtain the best performance from this appliance, you should: make sure that the commercially frozen foodstuffs were adequately stored by the retailer; be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time; not open the door frequently or leave it open longer than absolutely necessary. Once defrosted, food deteriorates rapidly and cannot be refrozen. Do not exceed the storage period indicated by the food manufacturer. 16 Important If there is a power failure when food is in the freezer, do not open the door of the freezer compartment. The frozen food will not be affected if the power cut is of short duration (up to 6-8 hours) and the freezer compartment is full, otherwise, it is recommended that the food should be used within a short time (a temperature increase of the frozen food shortens its safe storage period). Thawing Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation. Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer. Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment. Do not use metallic instruments to remove the trays from the freezer. Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates. It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole. Fig. 15 The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; remove any stored food, wrap it in several layers of newspaper and put it in a cool place; leave the door open, and insert the plastic scraper in the appropriate seating at the bottom centre, placing a basin underneath to collect the defrost water; Fig. 16 D037 D068 when defrosting is completed, dry the interior thoroughly; keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important: A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 17 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Periodic cleaning Clean the inside with warm water and bicarbonate of soda. Rinse and dry thoroughly. Interior light The light inside the refrigerator compartment is easy to get at through the opening in the light holder. If the light does not come on when the door is open, check that it is screwed into place properly. If it still does not light up, change the bulb. The rating is shown on the light bulb cover. Periods of non-operation Fig. 17 When the appliance is not in use for long periods, take the following precautions: remove the plug from the wall socket; remove all food; defrost and clean the interior and all accessories; leave the door ajar to allow air to circulate to prevent unpleasant smells. D400 CUSTOMER SERVICE AND SPARE PARTS If the appliance is not functioning properly, check that: the plug is firmly in the wall socket and the mains power switch is on; there is an electricity supply (find out by plugging in another appliance); the thermostat knob is in the correct position. If there are water drops on the bottom of the cabinet, check that the defrost water drain opening is not obstructed (see “Defrosting” section). If your appliance is still not working properly after making the above checks, contact the nearest service centre. To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom left-hand side. 18
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project