Juno JGI4424 User Manual

Add to My manuals
13 Pages

advertisement

Juno JGI4424 User Manual | Manualzz
JGI 4424
GEBRAUCHSANWEISUNG
OPERATING INSTRUCTION
D
t
2222736-13
t
CONTENTS
Instructions for the User
Instructions for the Installer
Important Safety Instructions
14
Technical specifications
20
Description of the Appliance
15
Installation
20
Use
16
Cleaning the interior
Control panel
Starting up
Temperature regulation
Quick freezing
Warning light
Acoustic alarm
Cold accumulators
Freezing calendar
Freezing of fresh foods
Storage of frozen food
Thawing
Ice-cube production
Tips
Tips for freezing
Tips for storage of frozen food
Maintenance
Defrosting
Periodic cleaning
Periodic of non-operation
Customer service and
spare parts
Positioning
Electrical connection
Door reversal
Instructions for totally built-in appliances
16
16
16
16
16
17
17
17
17
17
17
17
17
18
18
18
18
18
19
19
19
13
20
20
20
21
IMPORTANT SAFETY INSTRUCTIONS
It is most important that this instruction book should be retained with the appliance for future
reference.
Should the appliance be sold or transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is supplied with the appliance in order that the new owner can
be acquainted with the functioning of the appliance and the relevant warnings.
These warnings are provided in the interest of safety. You must read them carefully before installing or
using the appliance.
General Safety
■
■
■
■
■
■
■
■
■
■
■
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
It is dangerous to alter the specifications or modify
this product in any way.
Before any cleaning or maintenance work is
carried out, be sure to switch off and unplug the
appliance.
This appliance is heavy. Care should be taken
when moving it.
Ice follies can cause frost burns if consumed
straight from the appliance.
Take utmost care when handling your
appliance so as not to cause any damages to
the cooling unit with consequent possible fluid
leakages.
The appliance must not be located close to
radiators or gas cookers.
Avoid prolonged exposure of the appliance to
direct sunlight.
There must be adequate ventilation round the
back of the appliance and any damage to the
refrigerant circuit must be avoided.
For freezers only (except built-in models): an
ideal location is the cellar or basement.
Do not use other electrical appliances (such as
ice cream makers) inside of refrigerating
appliances.
■
Use
■
■
■
■
■
Service / Repair
■
■
■
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging must
therefore only be carried out by authorised
technicians.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
This appliance should be serviced by an
authorised Service Centre, and only genuine
spare parts should be used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
more serious malfunctioning. Refer to your local
Service Centre, and always insist on genuine
spare parts.
The domestic refrigerators and freezers are
designed to be used specifically for the storage of
edible foodstuffs only.
Frozen food must not be re-frozen once it has
been thawed out.
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
The inner lining of the appliance consists of
channels through which the refrigerant passes. If
these should be punctured this would damage the
appliance beyond repair and cause food loss. DO
NOT USE SHARP INSTRUMENTS to scrape off
frost or ice. Frost may be removed by using the
scraper provided. Under no circumstances should
solid ice be forced off the liner. Solid ice should be
allowed to thaw when defrosting the appliance.
See defrost instructions.
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to speed
up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it may
get damaged.
Installation
■
14
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cable is damaged, it must
be replaced by authorised service or qualified
personnel using a special cable of the same type.
■
■
■
■
t
During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
paragraph.
Attention: keep ventilation openings clear
of obstruction.
If the appliance is transported horizontally, it is
possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to
flow back in the compressor.
There are working parts in this product which heat
up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
■
If the appliance has been transported horizontally,
it is possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
Environment Protection
■
■
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from your
municipal authorities.
The materials used on this appliance marked
with the symbol
are recyclable.
DESCRIPTION OF THE APPLIANCE
➀ Freezer controls
➁ Compartment for freezing fresh food
➂ Compartment for frozen food storage
➀
➁
➁
➂
➂
15
6
5
4
1
3
2
USE
The freezer is marked with the
symbol, which means that the compartment is suitable for freezing
fresie food and long-term storage of frozen food.
Cleaning the interior
Before using the appliance for the first time, wash the
interior and all internal accessories with lukewarm
water and some neutral soap so as to remove the
typical smell of a brand-new product, then dry
thoroughly.
Do not use detergents or abrasive powders,
as these will damage the finish.
Control panel
6
5
4
1
3
➀ ➁➂➃ ➄
➀
➁
➂
2
➅
➃
➄
➅
Fast freeze switch and for stopping the acoustic
alarm (warning light on)
Fast freeze light (yellow)
Warning light (red)
Pilot light (green)
Push button ON/OFF
Thermostat control knob
Starting up
the lowest number and the maximum setting (coldest)
by the highest number.
The thermostat knob setting should be adjusted
depending on the inner temperature of the appliance,
which, in turn, depends on a number of factors, such
as:
• the ambient temperature
• the number of times the door is opened
• the quantity of food stored
• the location of the appliance.
Insert the plug into the wall socket. The appliance can
be activated/deactivated by pressing the ON/OFF
button ➄. Turn the thermostat control knob
clockwise beyond position «O» (OFF). The pilot light
➃ will light up to show that the appliance is on.
Freezer operation can be halted by turning knob
to position «O» or pressing again the ON/OFF button.
➅
➅
Temperature control
➅
Turn knob
beyond the «O» position until its pointer
coincides with the required setting.
To safely store frozen and deep-frozen foods, the
inner temperature of the freezer must be at least
-18°C or colder.
A medium setting is generally the most suitable.
The minimum setting (least cold) is represented by
Quick freezing
Activate fast freeze by depressing the fast freeze
switch ➀. The pilot lamp
will then light up. The
SUPER function can be ended by pressing the button
➀ again. The yellow light goes out.
➁
16
t
Warning light
➂
This light
warns when the temperature inside the
appliance has increased so much as to jeopardize the
preservation of food in the compartment.
When the appliance is switched on for the first time or
when food is placed in the compartment for freezing,
this light remains on until the temperature has
reached the level required for correct storage.
Food to be frozen has to be placed in the
appliance's two top compartments; if freezing only
a small amount of food, use the top compartment.
In the top compartment, products must only be
stacked up to the mark on the cabinet wall so as to
ensure that air circulation is not obstructed.
The maximum amount of food which is freezable
in 24 hours is indicated on the rating plate. This is
to be found on the bottom left-hand side.
You should never freeze all at once a greater quantity
of foods than the maximum indicated on the
appliance’s rating plate.
Acoustic alarm
This appliance also incorporates an alarm which
gives off a sound signal whenever the warning light
comes on. This signal can be temporarily stopped by
depressing the push button for fast freezing ➀.
The fast freezing push button can be released as
soon as the warning light is off.
Storage of frozen food
When you first start the freezer or if the freezer has
been out of use for some time, we advise you to run
your appliance for at least two hours in the «fast
freeze» mode before storing frozen food.
Cold accumulator
The freezer contains one cold accumulator which can
be found in the top compartment. The cold
accumulator increases storage times in the event of a
power cut or breakdown. It must be placed on top of
the food.
Removal of this unit will increase the capacity of the
fast freezing compartment but will reduce storage
times in the event of a power cut or breakdown.
Important
If there is a power failure when food is in
the freezer, do not open the door of the
freezer. The frozen food will not be affected
if the power cut is of short duration (up to
18 hours) and the freezer is full, otherwise,
it is recommended that the food should be
used within a short time (a temperature
increase of the frozen food shortens its safe
storage period).
Freezing Calendar
The symbols on the drawers show different types of
frozen goods.
The numbers indicate storage times in months for the
appropriate types of frozen goods. Whether the upper
or lower value of the indicated storage time is valid
depends on the quality of the foods and pre-treating
before freezing.
Thawing
Deep-frozen or frozen food, prior to being used, can
be thawed in the refrigerator or at room temperature,
depending on the time available for this operation.
Small pieces may even be cooked still frozen, directly
from the freezer: in this case, cooking will take longer.
Freezing of fresh foods
Ice-cube production
To quick-freeze foods when the appliance has not
been in use, switch on the freezer and let it run on the
quick-freeze setting for at least three hours before
putting the food to be frozen in the compartment.
If instead the appliance is already in operation, it
should run on the quick-freeze setting for at least 24
hours before the foods are put in the freezer. Once
the foods have been placed in the freezer, the
freezing operation can be considered to be complete
24 hours later. Once freezing is complete, the freezer
should be reset for normal storage use.
This appliance is equipped with one or more trays for
the production of ice-cubes.
Fill these trays with water, then put them in the
freezer.
Do not use metallic instruments to remove
the trays from the freezer.
17
TIPS
Tips for freezing fresh foods
Tips for storage of commercially
frozen food
To help you get the best out of the freezing process,
here are a few hints:
■ Freeze only good-quality, fresh and well-cleaned
foods. Split them into small portions to speed up
freezing and avoid having to thaw more food than
you require. It is in fact important to remember that
once the foods have thawed out, they deteriorate
fast.
■ Another point to remember is that lean foods keep
better and longer than fatty foods. Salt too reduces
storage times.
■ Wrap the foods in foil or polythene film, ensuring
that the wrapping adheres closely to the food and
is well sealed. In this way, by avoiding contact with
air, the colour flavour and nutritional value of the
foods remain intact.
■ During the freezing process, do not add further
foods for freezing and do not open the freezer
door.
■ The foods for freezing should not be placed in
contact with already frozen foods, but put in the
special freezing compartment. This will stop the
temperature of already frozen foods from rising.
■ Never put fizzy drinks in the freezer as they might
well burst.
■ In addition, never put hot foods or liquids in the
freezer compartment and take care not to fill
recipients up to the brim if they are covered with a
lid.
■ It is a good idea to mark the packs with the date
on which freezing started so that you can keep a
check on storage periods.
To get the best out of your freezer, in the case of
storage of commercially frozen food you should
ensure that:
■ the products have been correctly stored by the
retailer;
■ that there is only a very short time between when
you purchase the products and when you put them
in the freezer;
■ you do not store products for longer than the time
specified by the food manufacturer;
■ Avoid opening the door too frequently and when
you do open it, leave it open only for as long as is
strictly necessary;
■ A word of warning about ice lollies: they should not
be eaten straight out of the freezer as this might
cause cold burns.
MAINTENANCE
Defrosting
Unplug the appliance before carrying out
any maintenance operation.
The freezer compartment will become progressively
covered with frost. This should be removed with the
special plastic scraper provided, whenever the
thickness of the frost exceeds 1/4".
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
and it is advisable to carry out this operation when the
appliance is empty.
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.
18
t
To carry out complete defrosting proceed as follows:
1. Remove any stored food, wrap it in several layers
of newspaper and put it in a cool place.
2. Turn the thermostat control
to the «O» setting.
3. Leave the door open.
4. Introduce the plastic scraper in the appropriate
seating at the base of the cabinet as shown in the
figure and place a basin underneath to collect the
defrost water (see fig.).
5. When defrosting is completed dry the interior
thoroughly.
Keep the scraper for future use.
6. Turn the thermostat control to a medium setting
and, after letting the appliance run for at least two
hours in the «fast freeze» mode, replace the
previously removed food into the compartments.
➅
D068
Warning
Never use metal objects for defrosting your
appliance as it may get damaged.
Do not use a mechanical device or any
artificial means to speed up the thawing
process other than those recommended by
the manufacturer.
A temperature increase of the frozen food
shortens its safe storage period.
Periodic cleaning
Periods of non-operation
Never use metal objects for clearing your appliance
as it may get damaged. Clean the inside with warm
water and bicarbonate of soda. Rinse and dry
thoroughly.
To guarantee a safe operation of the fridge, once a
year remove the ventilation grille at the base and
clean the air channels with a vacuum cleaner.
When the appliance is not in use for long periods,
take the following precautions:
remove the plug from the wall socket;
remove all food:
defrost and clean the interior and all accessories;
leave the door ajar to allow air to circulate to prevent
unpleasant smells.
CUSTOMER SERVICE AND
SPARE PARTS
If the appliance is not functioning properly, check that:
the plug is firmly in the wall socket and the mains
power switch is on;
If your appliance is still not working properly after
making the above checks, contact the nearest service
centre.
To obtain fast service, it is essential that when
you apply for it you specify the model and serial
number of your appliance which can be found on
the guarantee certificate or on the rating plate
located inside the appliance, on the bottom lefthand side.
there is an electricity supply (find out by plugging in
another appliance);
the thermostat knob is in the correct position.
19
TECHNICAL SPECIFICATIONS
The technical data is indicated in the rating plate on the left side inside the appliance.
INSTALLATION
lf this appliance featuring magnetic door seals is
to replace an older appliance having a spring lock
(latch) on the door or lid, be sure to make that
spring lock unusable before you discard the old
appliance. This will prevent it from becoming a
death-trap for a child.
This appliance complies with EEC directive
number, 87/308 of 2/6/87 relative to radio
interference suppression.
This appliance complies with the following
E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and
subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Positioning
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.
Best performance is obtained with ambient
temperature between +18°C and +43°C (class T);
+18°C and +38°C (class ST); +16°C and +32°C
(class N); +10°C and +32°C (class SN).
The class of your appliance is shown on its rating
plate.
For building-in and door reversibility refer to the
relevant instructions.
Door reversibility
The appliance’s door has been locked in position for
transport by means of pins on both sides. According
to the door opening direction, remove relevant pins at
the top and at the bottom.
A
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.
B
D163
Warning!
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting
of the gasket or accelerate this process by
heating up the part involved with a normal
hairdrier.
Important
The appliance must be earthed.
The power supply cable plug is provided with a
contact for this purpose.
If the domestic power supply socket is not
earthed. connect the appliance to a separate
earth in compliance with current regulations,
consulting a specialist technician.
The Manufacturer declines all responsibility if the
above safety precautions are not observed.
Attention!
It must be possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
20
t
Instructions for totally built-in
appliances
Dimensions of the recess
Height of housing
Depth of housing
Width of housing
A
mm 880
mm 550
mm 560
50
540
0
56
55
0
880
D022
3. Slide the appliance into the recess, pushing it
against the wall on the handle side.
PR 32
50 mm
min.
200 cm
2
1. It is necessary that the niche is provided with a
conduct of ventilation having the following
dimensions:
Depth 50 mm
Width 540 mm
D
C
D727
4. Open the door and push the appliance against the
side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws
provided in the kit included with the appliance.
Snap vent grille (C) and hinge cover (D) into
position.
min.
cm 200
2
D526
For safety reasons, minimum ventilation must be
as shown in Fig.
Attention: keep ventilation openings clear of
obstruction.
B
D013
5. Apply covers (B) on joint cover lugs and into hinge
holes.
D132
2. Apply joint the sealing strip as shown in figure.
21
8mm
B
A
C
A
D
PR266
PR167
6. Separate parts A, B, C, D as shown in the figure.
B
50mm
9. Open the appliance door and the furniture door at
90°. Insert the small square (B) into guide (A). Put
together the appliance door and the furniture door
and mark the holes as indicated in the figure.
Remove the squares and drill holes with Ø 2 mm at
8 mm from the outer edge of the door. Place the
small square on the guide again and fix it with the
screws supplied.
A
20m
m
PR166
7. Place guide (A) on the inside part of the furniture
door, up and down as shown in the figure and mark
the position of external holes. After having drilled
holes, fix the guide with the screws supplied.
PR168
10. Should the lining up of the furniture door be
necessary, use the clearance of slots. At the end
of operations, it is necessary to check if the door
of the furniture closes properly.
A
C
PR33/2
8. Fix cover (C) on guide (A) until it clips into place.
B
D
PR167/1
11. Fix cover (D) on guide (B) until it clips into place.
22

advertisement

Related manuals

advertisement