Electrolux ERN1672 User Manual

Add to My manuals
10 Pages

advertisement

Electrolux ERN1672 User Manual | Manualzz
k ü h l s c h r a n k / r e f r i g e r a t o r / k y l s k å p / j ä ä k a a p p i / хoлoдильник
GEBRAUCHSANWEISUNGEN
INSTRUCTION BOOKLET
BRUKSANVISNING
KÄYTTÖOHJE
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
D
ERN 1672
GB
S
FIN
2222 751-84
RUS
t
Safety Instructions
Please read these operating instructions
carefully before installing the appliance. These
warnings are provided in the interests of your
safety. Ensure you fully understand them before
installing or using the appliance. If you are
unsure about the meaning of these warnings
contact the Customer Care Department.
Domestic Use
¥ The domestic refrigerators and freezers are
designed to be used specifically for the storage of
edible foodstuffs only.
¥ Check the appliance for transport damage. Under
no circumstances should a damaged appliance be
installed. In the event of damage please contact
your retailer.
¥ This appliance is heavy. The edges and projecting
parts of the cabinet may be sharp. Be careful when
moving the cabinet and always use gloves.
¥ Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
¥ Ensure that the appliance does not stand on the
electrical supply cable.
¥ Do not use electrical appliances inside the
appliance
¥ Do not keep carbonated drinks or bottles in the freezer
compartment. The glass bottles may break.
¥ Ice lollies can cause Ôfrost/freezer burnsÕ if
consumed straight from the freezer.
¥ It is dangerous to try and alter the specifications or
modify this product in any way.
¥ Under no circumstances should you attempt to
repair the appliance yourself. Refer to your local
Service Centre, and always insist on genuine spare
parts.
Child Safety
¥ This appliance is designed to be operated by
adults only. There is a risk of suffocation! Keep
packaging material away from children!
¥ In case of disposal of the appliance, cut off the
supply cable as close as possible and make
thelock unusable, to prevent children from closing
themselves inside the appliances.
Environment Protection
¥ This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with the
urban refuse and rubbish. Avoid damaging the
cooling unit, especially at the rear near the heat
exchanger. Information on your local disposal sites
may be obtained from your municipal authorities.
¥ The materials used on this appliance marked with
the symbol
are recyclable.
Index
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Use and Control Before Use / Starting the appliance / Temperatur control / Internal parts . . . . . . . . . . . . . . .11
Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Maintenance Defrosting / Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Something not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Customer Service and Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Installation Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Door reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Building-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
10
Use and Control
Before Use
Wait two hours before connecting the appliance
to allow the oil to flow back in the compressor.
¥ Before using the appliance for the first time, wash
the interior and all internal accessories with
lukewarm water and some neutral soap so as to
remove the typical smell of a brand-new product,
then dry thoroughly.
Internal Parts
Storage shelves
¥ The shelves can be removed for cleaning.
¥ To permit storage of food packages of various
sizes, the shelves can be placed at different
heights.
¥ To remove the internal shelf pull forward until it can
be tipped up or down and removed.
Do not use detergents or abrasive powders,
as these will damage the finish.
¥ Remove safety elements used for transportation.
Starting the appliance
¥ Insert the plug into the wall socket and turn the
thermostat knob clockwise beyond position ÇOÈ
(OFF).
D338
¥ Please do the same in reverse to insert the shelf at
a different height.
The glass shelf above the vegetable drawers
and the bottle shelf should always remain in
position, to ensure correct air circulation.
¥ Turn the thermostat control to the required setting.
Temperature Control
¥ The thermostat control situated inside the fridge
compartment regulates the temperature of the
appliance.
¥ It allows you to adjust the temperature inside the
refrigerator according to use and external
conditions.
¥ Setting ã1Ò = hightest temperature, warmest
setting
¥ Setting ã6Ò = lowest temperature, coldest
setting.
¥ Setting ã0Ò = Off
A medium setting is generally the most suitable.
¥ To permit storage of food packages of various
sizes, the central door shelf can be adjusted in
height.
¥ Gradually pull the shelf in the direction of the
arrows until it comes free, then reposition as
required.
¥ For more thorough cleaning, the top and bottom
door sheves can be removed by pulling them in the
direction of the arrows, then refitting them in
position.
11
Hints
Hints for refrigeration
Saving Energy
¥ Pay careful attention to where the cabinet is
placed. See the section ÒInstallationÓ. When
installed correctly the cabinet will consume less
energy.
¥ Try to avoid keeping the doors open for long
periods or opening the doors too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
¥ If the ambient temperature is high, the thermostat
knob is on the coldest setting (higher numbers) and
the appliance is fully loaded, the compressor may
run continuously, causing frost or ice to form on the
evaporator. If this happens, turn the knob to a
warmer setting (lower numbers) to allow automatic
defrosting and so a saving in electricity
consumption.
¥ Do not place warm foods inside the appliance.
Allow warm foods to cool first.
¥ Keep the heat emitting condenser, the metall grille
on the rear wall of your appliance, always clean.
¥ Do not store warm food or evaporating liquids in
the refrigerator and do cover or wrap up the food,
particularly if it has a strong smell.
To help you use your refrigerator correctly, here are
some useful hints:
¥ Raw meat (beef, pork, lamb & poultry): wrap in
polythene bags and place on top of the salad
compartment, this being the coldest spot in the
refrigerator.
Meat can only be stored safely in this way for
one or two days at the most.
¥ Cooked food, cold cuts, jelly, etc.: these should
be well covered and can be stored on any of the
glass shelves.
¥ Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom drawer.
¥ Butter & cheese: these should be placed in
special airtight containers or wrapped in aluminium
foil or polythene bags to keep out as much air as
possible.
¥ Milk bottles: these should have a top and should
be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
Maintenance
Unplug the appliance before carrying out
any maintenance operation.
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.
Defrosting
Cleaning
¥ Defrosting the refrigerator compartment is
automatic. The defrost water drains out through a
trough into a container at the back of the appliance,
above the motor compressor, where it evaporates.
¥ It is important to periodically clean the defrost
water drain hole.
Never use metal objects for cleaning your
appliance as it may get damaged.
NEVER use detergents, abrasive powders,
highly perfumed cleaning products or wax
polishes to clean the interior as these will
damage the surface and leave a strong
odour.
Clean the inside with warm water and bicarbonate of
soda. Rinse and dry thoroughly.
To guarantee a safe operation of the fridge, once a
year remove the ventilation grille at the base and
clean the air channels with a vacuum cleaner.
D037
12
When the appliance is not in use
Changing the light bulb
Disconnect the appliance from the electricity supply.
Empty all foods and clean the appliance, leaving the
doors ajar to prevent unpleasant smells.
¥ Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows:
1. unscrew the light cover securing screws.
2. unhook the moving part by pressing it as shown
in the figure.
3. Replace the bulb by other with another with the
same charcteristics.
D411
Something not Working
Problems may be due to causes which can easily be solved before calling the Technical Service. Please
follow these instructions:
SYMPTOM
SOLUTION
Door does not close
Level properly the appliances if it is not well levelled.
Weight surpasses the storage limit of the door shelf so spread weight more evenly or
take some products out.
Readjust the door if it is not properly aligned.
It is too warm inside the refrigerator
Set a lower temperature.
Distribute the food products to allow cold air to circulate around them.
Make sure that the door is completely closed and that the insulating strip is complete
and clean.
The temperature where the cabinet is placed is above normal room temperature.
It is too cold inside the refrigerator.
Set a warmer temperature.
The compressor works continuously.
Turn the thermostat knob to a lower number.
The temperature where the cabinet is placed is above normal room temperature.
Check that the ventilation is sufficient and that the ventilation openings are
unobstructed.
The cause could be the introduction of large quantities of food and/or frequent
opening/closing of the door.
There is water inside/outside the refrigerator.
Sometimes is normal. During automatic defrosting frost thaws on the cooling plate.
Water comes out on the floor.
Place the drain hose at the back of the cabinet above the drain bowl.
Noises
Sometimes this is normal. Temperature control may cause clicking sounds when the
system is connected or disconnected.
The injected cooling gas may produce a gurgling sound while passing through the
tubes.
The motor may cause a humming noise and/or slight bumping.
The insulation material used has a tendency to slighly increase noise levels, how ever it
allows for much better insulation and a lower energy consumption.
13
Customer service and spare parts
If you cannot find the remedy for a malfunction in
these operating instructions, please contact your
dealer or our customer service department and
consult the Guarantee card.
Selective ordering of replacement parts can save
unnecessary travel and costs.
For this reason always provide the following
appliance information:
¥ Model Name
¥ Model Number (PNC)
¥ Serial Number (S-No.)
This information can be found on the rating plate
inside the cabenit on the left hand wall. We
recommend that you enter this information here, so
that it is handy if needed.
Technical specifications
The technical data is indicated in the rating plate on the left side inside the appliance.
Installation
Take utmost care when handling your
appliance so as not to cause any damages to
the cooling unit with consequent possible fluid
leakages.
¥ During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
¥ Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly available from the manufacturer or its service agent.
Positioning
¥ Unpack the cabinet and check that it is in good
condition and free of any transport damage.
¥ Place the refrigerator away from direct sunlight and
heat sources.
¥ Maintain recommended ventilation.
It is necessary that the niche is provided with a
50
conduct of venti0
4
5
lation having the
f o l l o w i n g
dimensions:
3
Depth
50 mm
Width
540 mm
2 1
14
The climate classification can be found on the rating
plate, which is located inside the cabinet on the left
hand wall.
The following table shows which ambient
temperature is correct for each climate classification:
Climate
classification
for an ambient temperature of
SN
+10 to +32¡C
N
+16 to +32¡C
ST
+18 to +38¡C
T
+18 to +43¡C
When the ambient temperature is not included
within the range indicated for the class of this
appliance, the storage temperature in the
appliance cannot be guaranteed; therefore it is
advisable to use the food stored as soon as
possible.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.
Important
The appliance must be earthed.
The power supply cable plug is provided with a
contact for this purpose.
If the domestic power supply socket is not
earthed. connect the appliance to a separate
earth in compliance with current regulations,
consulting a specialist technician.
The
Manufacturer
declines
all
responsibility if the above safety
precautions are not observed.
This appliance complies with the following E.E.C.
Directives:
- 87/308 EEC of 2/6/87 relative to radio
interference suppression.
- 73/23 EEC of 19.2.73 (Low Voltage
D
i
r
e
c
t
i
v
e
)
and subsequent modifications.
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Attention!
It must be possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
Door reversal
The applianceÕs door has been locked in position for
transport by means of pins on both sides. According
to the door opening direction, remove relevant pins
at the top and at the bottom.
A
Warning!
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting
of the gasket or accelerate this process by
heating up the part involved with a normal
hairdrier.
B
D163
15
Building-in
Dimensions of the recess
Height of housing
Depth of housing
Width of housing
3. Open the door and push the appliance against the
side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4
screws provided in the kit included with the
appliance. Snap vent grille (C) and hinge cover (D)
into position.
mm 880
mm 550
mm 560
50
540
0
56
55
0
880
D
PR 32
C
D727
1. Slide the appliance into the recess, pushing it
against the wall on the handle side.
4. Apply covers (B) on joint cover lugs and into hinge
holes.
A
B
D022
2. Apply joint the sealing strip as shown in figure.
D013
5. Separate parts A, B, C, D as shown in the figure.
B
A
C
D
D132
16
PR266
6. Place guide (A) on the inside part of the furniture
door, up and down as shown in the figure and
mark the position of external holes. After having
drilled holes, fix the guide with the screws
supplied.
9. Should the lining up of the furniture door be
necessary, use the clearance of slots. At the end
of operations, it is necessary to check if the door
of the furniture closes properly.
50mm
A
20m
m
PR168
PR166
10. Fix cover (D) on guide (B) until it clips into place.
7. Fix cover (C) on guide (A) until it clips into place.
A
B
C
D
PR167/1
PR33/2
8. Open the appliance door and the furniture door at
90¡. Insert the small square (B) into guide (A). Put
together the appliance door and the furniture door
and mark the holes as indicated in the figure.
Remove the squares and drill holes with ¯ 2 mm
at 8 mm from the outer edge of the door. Place the
small square on the guide again and fix it with the
screws supplied.
8mm
A
PR167
B
17
Electrolux HemProdukter AB
923 631 693
S-105 45 Stockholm
www.electrolux.se
ELECTROLUX HOME PRODUCTS OPERATIONS EUROPE

advertisement

Related manuals

advertisement