AEG | SCT71900S0 | User manual | Aeg SCT71900S0 User Manual

EN
User Manual
Fridge Freezer
SCT71900S0
2
www.aeg.com
CONTENTS
1. SAFETY INFORMATION.................................................................................................3
2. SAFETY INSTRUCTIONS................................................................................................ 4
3. OPERATION.................................................................................................................... 6
4. FIRST USE........................................................................................................................ 8
5. DAILY USE........................................................................................................................8
6. HINTS AND TIPS........................................................................................................... 10
7. CARE AND CLEANING................................................................................................ 11
8. TROUBLESHOOTING...................................................................................................12
9. INSTALLATION............................................................................................................. 15
10. NOISES........................................................................................................................ 20
11. TECHNICAL INFORMATION.....................................................................................21
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you impeccable
performance for many years, with innovative technologies that help make life simpler
features you might not find on ordinary appliances. Please spend a few minutes
reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following
data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
ENGLISH
1.
3
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible if an incorrect
installation and use causes injuries and damages. Always
keep the instructions with the appliance for future
reference.
1.1 Children and vulnerable people safety
•
•
•
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Do not let children play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Keep all packaging away from children.
1.2 General Safety
•
•
•
•
•
This appliance is intended to be used in household
and similar applications such as:
– Farm houses; staff kitchen areas in shops, offices
and other working environments
– By clients in hotels, motels, bed and breakfast and
other residential type environments
Keep ventilation openings, in the appliance enclosure
or in the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance, unless they
are of the type recommended by the manufacturer.
4
www.aeg.com
•
•
•
•
Do not use water spray and steam to clean the
appliance.
Clean the appliance with a moist soft cloth. Only use
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
Do not store explosive substances such as aerosol
cans with a flammable propellant in this appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, its Authorised Service Centre or
similarly qualified persons in order to avoid a hazard.
2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Obey the installation instruction
supplied with the appliance.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Make sure the air can circulate around
the appliance.
• Wait at least 4 hours before
connecting the appliance to the
power supply. This is to allow the oil
to flow back in the compressor.
• Do not install the appliance close to
radiators or cookers, oven or hobs.
• The rear of the appliance must stand
against the wall.
• Do not install the appliance where
there is direct sunlight.
• Do not install this appliance in areas
that are too humid or too colds, such
as the construction appendices,
garages or wine cellars.
• When you move the appliance, lift it
by the front edge to avoid scratching
the floor.
2.2 Electrical connection
WARNING!
Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the electrical
information on the rating plate agrees
with the power supply. If not, contact
an electrician.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the electrical components (e.g. mains
plug, mains cable, compressor).
Contact the Authorised Service
Centre or an electrician to change the
electrical components.
• The mains cable must stay below the
level of the mains plug.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
2.3 Use
WARNING!
Risk of injury, burns,
electrical shock or fire.
ENGLISH
• Do not change the specification of
this appliance.
• Do not put electrical appliances (e.g.
ice cream makers) in the appliance
unless they are stated applicable by
the manufacturer.
• Be careful not to cause damage to
the refrigerant circuit. It contains
isobutane (R600a), a natural gas with a
high level of environmental
compatibility. This gas is flammable.
• If damage occurs to the refrigerant
circuit, make sure that there are no
flames and sources of ignition in the
room. Ventilate the room.
• Do not let hot items to touch the
plastic parts of the appliance.
• Do not put soft drinks in the freezer
compartment. This will create
pressure on the drink container.
• Do not store flammable gas and
liquid in the appliance.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not touch the compressor or the
condenser. They are hot.
• Do not remove or touch items from
the freezer compartment if your hands
are wet or damp.
• Do not freeze again food that has
been thawed.
• Obey the storage instructions on the
packaging of frozen food.
2.4 Care and cleaning
WARNING!
Risk of injury or damage to
the appliance.
5
• Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
• This appliance contains hydrocarbons
in the cooling unit. Only a qualified
person must do the maintenance and
the recharging of the unit.
• Regularly examine the drain of the
appliance and if necessary, clean it. If
the drain is blocked, defrosted water
collects in the bottom of the
appliance.
2.5 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door to prevent children
and pets to be closed inside of the
appliance.
• The refrigerant circuit and the
insulation materials of this appliance
are ozone-friendly.
• The insulation foam contains
flammable gas. Contact your
municipal authority for information on
how to discard the appliance
correctly.
• Do not cause damage to the part of
the cooling unit that is near the heat
exchanger.
6
www.aeg.com
3. OPERATION
3.1 Control panel
1 Fridge Pilot light
2 Fridge ON/OFF switch
3 Fridge temperature regulator /+
button
4 Fridge temperature indicator
5 Fridge temperature regulator / button
6 DYNAMICAIR indicator
7 DYNAMICAIR button
8 Appliance Pilot light
9 Appliance ON/OFF switch
10 Freezer temperature regulator / +
button
11 Freezer temperature indicator
12 Freezer temperature regulator / button
13 FROSTMATIC indicator
14 FROSTMATIC button
15 Alarm indicator
16 Alarm reset button
3.2 Switching on
buttons are connected to the
temperature indicator.
1. Insert the plug into the wall socket.
2. Press the ON/OFF switch.
The Pilot light will light up.
The alarm indicator light flashes since the
temperature is reached. The acoustic
alarm sounds.
3. Press the alarm reset to reset the
alarm.
3.3 Switching off
To switch off fridge or appliance reaped
the procedure:
1. Press ON/OFF for 5 seconds.
2. Countdown from -3-2-1 will shown.
When -1- appears the fridge /
appliance is turned off. The
temperature indicators and Pilot light
switch off.
3.4 Temperature regulation
The temperature is adjusted using the
temperature setting buttons. These
To operate the appliance, proceed as
follows:
• Set the temperature by pressing
temperature regulator.
The temperature indicators will shown
the changed setting and temperature
indicator flashes.
• Each time by pressing the
temperature regulator the
temperature rise by 1°C.
The set temperature will be
reached within 24 hours. The
temperature indicator will
illuminate.
For correct storage of the foodstuff
following temperatures should be set:
• fridge : +5°C
• freezer : -18 °C
ENGLISH
When the setting is changed
the compressor does not
start immediately if
automatic defrosting is
currently taking place. As the
storage temperature in the
fridge is reached quickly
store food immediately after
switching on.
3.5 Temperature indicators
The temperature indicators show several
information:
• During normal operating the
temperature set for fridge and freezer
are displayed;
• During adjusting temperature flashing
display indicates the fridge or freezer
current set.
3.6 Temperature setting
buttons
The temperature is adjusted using the
temperature setting buttons. These
buttons are connected to the
temperature indicator.
Press on of the two temperature setting
buttons is to adjust the temperature 1°C
increments.
The set temperature will be reached
within 24 hours.
3.7 High temperature alarm
Temperature increase in the freezer
compartment (for example due to an
earlier power failure or door is open) is
indicated by:
• alarm light flashing;
• sounding of a buzzer.
1. Switch off the buzzer by pressing the
alarm reset button. Alarm indicator
light will flash.
2. Press alarm reset button.
The alarm indicator light is off at the
same time freezer temperature
indicator is shown for 5 seconds the
warmest temperature reached in the
freezer compartment.
7
When normal conditions are
restored, the alarm stop
flashing and the buzzer turn
off automatically.
3.8 COOLMATIC function
The COOLMATIC function is suitable for
quick cooling of large quantities of
goods in the refrigerator.
To activate the function:
• Press the fridge temperature - button
(several times if necessary) until the
word SC appears in the display.
A temperature of +2°C is
automatically selected.
To deactivate the function:
• Press the fridge temperature +
button .
The COOLMATIC function
stops automatically after
about 6 hours.
If the COOLMATIC function is switched
on the temperature setting may not be
changed.
3.9 FROSTMATIC function
The FROSTMATIC function accelerates
the freezing of fresh food and, at the
same time, protects foodstuffs already
stored from undesirable warming.
To switch on the fuction:
• Press the FROSTMATIC button.
The FROSTMATIC indicator will light
up.
To switch off the function before its
automatic end, repeat the steps until
FROSTMATIC indicator goes off.
The FROSTMATIC function
stops automatically after
about 52 hours.
If the FROSTMATIC function is switched
on the temperature setting may not be
changed.
3.10 Holiday function
This function allows you to keep the
refrigerator shut and empty during a
8
www.aeg.com
long holiday period without the
formation of a bad smell.
The fridge compartment
must be empty when the
holiday function is on.
To activate the function:
• Press the temperature regulator
(warmest) until the letter H (Holiday)
appears on the temperature indicator.
The Holiday function sets the
temperature approximately +15°C.
The refrigerator is in the energy saving
set.
To switch off the function press the
fridge temperature regulator to set
required temperature.
3.11 DYNAMICAIR function
To switch on the function:
• Press the DYNAMICAIR button.
The DYNAMICAIR indicator is shown.
To switch off the function before its
automatic end, repeat the steps until
DYNAMICAIR indicator goes off.
If the function is activated
automatically the
DYNAMICAIR indicator is
not shown (refer to "Daily
use"). The activation of the
DYNAMICAIR function
increases the energy
consumption.
4. FIRST USE
4.1 Cleaning the interior
Before using the appliance for the first
time, the interior and all internal
accessories should be washed with
lukewarm water and some neutral soap
to remove the typical smell of a brandnew product, then dried thoroughly.
5. DAILY USE
WARNING!
Refer to Safety chapters.
5.1 Positioning the door
shelves
To permit storage of food packages of
various sizes, the door shelves can be
placed at different heights.
1. Gradually pull the shelf in the
direction of the arrows until it comes
free.
2. Reposition as required.
CAUTION!
Do not use detergents or
abrasive powders, as these
will damage the finish.
ENGLISH
5.2 Movable shelves
The walls of the refrigerator are
equipped with a series of runners so that
the shelves can be positioned as desired.
Do not move the glass shelf
above the vegetable drawer
and the bottle shelf to
ensure correct air circulation.
5.3 MaxiBox drawer
9
opening or when the ambient
temperature is high.
The DYNAMICAIR device
stops when the door is open
and restarts immediately
after the door closing.
5.5 Freezing fresh food
The freezer compartment is suitable for
freezing fresh food and storing frozen
and deep-frozen food for a long time.
The maximum amount of food that can
be frozen in 24 hours is specified on the
rating plate, a label located on the
inside of the appliance.
The drawer is suitable for storing fruit
and vegetables.
1. To freeze fresh food activate the
FROSTMATIC function at least 24
hours before placing the food to be
frozen in the freezer compartment.
2. Place the fresh food to be frozen in
the upper compartment.
The freezing process lasts 24 hours:
during this period do not add other food
to be frozen.
There is a separator inside the drawer
that can be placed in different positions
to allow for the subdivision best suited to
personal needs.
5.6 Storage of frozen food
There is a grille (if foreseen) on the
bottom of the drawer to separate the
fruit and vegetables from any humidity
that may form on the bottom surface.
When first starting-up or after a period
out of use, before putting the products
in the compartment let the appliance run
at least 2 hours on the higher settings.
All parts inside the drawer can be
removed for cleaning purposes
5.4 DYNAMICAIR
The refrigerator compartment is
equipped with a device that allows for
rapid cooling of foods and more uniform
temperature in the compartment.
This device activates by itself when
needed, for example for a quick
temperature recovering after door
10
www.aeg.com
WARNING!
In the event of accidental
defrosting, for example due
to a power failure, if the
power has been off for
longer than the value shown
in the technical
characteristics chart under
"rising time", the defrosted
food must be consumed
quickly or cooked
immediately and then refrozen (after cooling).
5.7 Thawing
Deep-frozen or frozen food, prior to
being used, can be thawed in the
refrigerator compartment or at room
temperature, depending on the time
available for this operation.
5.8 Ice-cube production
This appliance is equipped with one or
more trays for the production of icecubes.
Do not use metallic
instruments to remove the
trays from the freezer.
1. Fill these trays with water
2. Put the ice trays in the freezer
compartment.
5.9 Cold accumulators
The freezer contains at least one cold
accumulator which increases storage
time in the event of a power cut or
breakdown.
Small pieces may even be cooked still
frozen, directly from the freezer: in this
case, cooking will take longer.
6. HINTS AND TIPS
6.1 Normal operating sounds
The following sounds are normal during
operation:
• A faint gurgling and bubbling sound
from coils sound when refrigerant is
pumped.
• A whirring and pulsating sound from
the compressor when refrigerant is
pumped.
• A sudden cracking noise from inside
appliance caused by thermic
dilatation (a natural and not
dangerous physical phenomenon).
• A faint click noise from the
temperature regulator when the
compressor switches on or off.
6.2 Hints for energy saving
• Do not open the door frequently or
leave it open longer than absolutely
necessary.
• If the ambient temperature is high
and the Temperature Regulator is set
to low temperature and the appliance
is fully loaded, the compressor may
run continuously, causing frost or ice
on the evaporator. If this happens, set
the Temperature Regulator toward
warmer settings to allow automatic
defrosting and so a saving in
electricity consumption.
• If foreseen, do not remove the cold
accumulators from the freezer basket.
6.3 Hints for fresh food
refrigeration
To obtain the best performance:
• do not store warm food or
evaporating liquids in the refrigerator
• do cover or wrap the food, particularly
if it has a strong flavour
• position food so that air can circulate
freely around it
6.4 Hints for refrigeration
Useful hints:
• Meat (all types): wrap in a suitable
packaging and place it on the glass
shelf above the vegetable drawer.
Store meat for at most 1-2 days.
ENGLISH
• Cooked foods, cold dishes: cover and
place on any shelf.
• Fruit and vegetables: clean
thoroughly and place in a special
drawer. Bananas, potatoes, onions
and garlic must not be kept in the
refrigerator if not packed.
• Butter and cheese: place in a special
airtight container or wrap in an
aluminium foil or a polythene bag to
exclude as much air as possible.
• Bottles: close with a cap and place on
the door bottle shelf, or (if available)
on the bottle rack.
6.5 Hints for freezing
To help you make the most of the
freezing process, here are some
important hints:
• the maximum quantity of food which
can be frozen in 24 hours is shown on
the rating plate;
• the freezing process takes 24 hours
no further food to be frozen should
be added during this period;
• freeze only top quality, fresh and
thoroughly cleaned, foodstuffs;
• prepare food in small portions to
enable it to be rapidly and completely
frozen and to make it possible
subsequently to thaw only the
quantity required;
• wrap up the food in aluminium foil or
polythene and make sure that the
packages are airtight;
• do not allow fresh, unfrozen food to
touch food which is already frozen,
thus avoiding a rise in temperature of
the latter;
• lean foods store better and longer
than fatty ones; salt reduces the
storage life of food;
• water ices, if consumed immediately
after removal from the freezer
compartment, can possibly cause the
skin to be freeze burnt;
• it is advisable to show the freezing in
date on each individual pack to
enable you to keep tab of the storage
time.
6.6 Hints for storage of frozen
food
To obtain the best performance from this
appliance, you should:
• make sure that the commercially
frozen foodstuffs were adequately
stored by the retailer;
• be sure that frozen foodstuffs are
transferred from the foodstore to the
freezer in the shortest possible time;
• not open the door frequently or leave
it open longer than absolutely
necessary;
• once defrosted, food deteriorates
rapidly and cannot be refrozen;
• do not exceed the storage period
indicated by the food manufacturer.
7. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
7.1 General warnings
CAUTION!
Unplug the appliance before
carrying out any
maintenance operation.
11
This appliance contains
hydrocarbons in its cooling
unit; maintenance and
recharging must therefore
only be carried out by
authorized technicians.
The accessories and parts of
the appliance are not
suitable for washing in a
dishwasher.
12
www.aeg.com
7.2 Periodic cleaning
CAUTION!
Do not pull, move or
damage any pipes and/or
cables inside the cabinet.
the refrigerator compartment channel to
prevent the water overflowing and
dripping onto the food inside.
CAUTION!
Take care of not to damage
the cooling system.
CAUTION!
When moving the cabinet,
lift it by the front edge to
avoid scratching the floor.
The equipment has to be cleaned
regularly:
1. Clean the inside and accessories with
lukewarm water and some neutral
soap.
2. Regularly check the door seals and
wipe clean to ensure they are clean
and free from debris.
3. Rinse and dry thoroughly.
4. If accessible, clean the condenser
and the compressor at the back of
the appliance with a brush.
This operation will improve the
performance of the appliance and
save electricity consumption.
7.3 Defrosting of the
refrigerator
Frost is automatically eliminated from the
evaporator of the refrigerator
compartment every time the motor
compressor stops, during normal use.
The defrost water drains out through a
trough into a special container at the
back of the appliance, over the motor
compressor, where it evaporates.
It is important to periodically clean the
defrost water drain hole in the middle of
8. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
7.4 Defrosting the freezer
The freezer compartment is frost free.
This means that there is no build up of
frost when it is in operation, neither on
the internal walls nor on the foods.
The absence of frost is due to the
continuous circulation of cold air inside
the compartment, driven by an
automatically controlled fan.
7.5 Periods of non-operation
When the appliance is not in use for long
periods, take the following precautions:
1. Disconnect the appliance from
electricity supply.
2. Remove all food.
3. Clean the appliance and all
accessories.
4. Leave the door/doors open to
prevent unpleasant smells.
WARNING!
If you want to keep the
appliance switched on, ask
somebody to check it once
in a while to prevent the
food inside from spoiling in
case of a power failure.
ENGLISH
13
8.1 What to do if...
Problem
Possible cause
Solution
The appliance does not operate.
The appliance is switched
off.
Switch on the appliance.
The mains plug is not con- Connect the mains plug to the
nected to the mains socket mains socket correctly.
correctly.
There is no voltage in the
mains socket.
Connect a different electrical
appliance to the mains socket.
Contact a qualified electrician.
The Pilot light flashes
The appliance is not working properly.
Contact a qualified electrician.
The appliance is noisy.
The appliance is not supported properly.
Check if the appliance stands
stable.
The lamp does not work.
The lamp is in stand-by.
Close and open the door.
The lamp does not work.
The lamp is defective.
Contact the nearest Authorised Service Centre.
The compressor operates
continually.
Temperature is set incorrectly.
Refer to "Operation".
Many food products were
put in at the same time.
Wait some hours and then
check the temperature again.
The room temperature is
too high.
Refer to climate class chart on
the rating plate.
Food products placed in
the appliance were too
warm.
Allow food products to cool to
room temperature before storing.
The door is not closed cor- Refer to "Closing the door".
rectly.
The FROSTMATIC is
switched on.
Refer to "FROSTMATIC ".
The COOLMATIC is
switched on.
Refer to "COOLMATIC ".
There is too much frost and
ice.
The door is not closed cor- Refer to "Closing the door".
rectly or the gasket is deformed/dirty.
The compressor does not
start immediately after
pressing the FROSTMATIC,
or after changing the temperature.
This is normal, no error has The compressor starts after a
occurred.
period of time.
14
www.aeg.com
Problem
Possible cause
Solution
The compressor does not
start immediately after
pressing the COOLMATIC,
or after changing the temperature.
This is normal, no error has The compressor starts after a
occurred.
period of time.
Water flows on the rear
plate of the refrigerator.
During the automatic defrosting process, frost
melts on the rear plate.
Water flows inside the refrig- The water outlet is clogerator.
ged.
Food products prevent
that water flows into the
water collector.
This is correct.
Clean the water outlet.
Make sure that food products
do not touch the rear plate.
Water flows on the floor.
The melting water outlet is Attach the melting water outnot connected to the
let to the evaporative tray.
evaporative tray above the
compressor.
The temperature in the appliance is too low/too high.
The temperature regulator Set a higher/lower temperais not set correctly.
ture.
The door is not closed cor- Refer to "Closing the door".
rectly.
The food products' temperature is too high.
Let the food products temperature decrease to room temperature before storage.
Many food products are
stored at the same time.
Store less food products at the
same time.
The door has been
opened often.
Open the door only if necessary.
There is no cold air circula- Make sure that there is cold air
tion in the appliance.
circulation in the appliance.
If the advice does not lead
to the desired result, contact
the nearest Authorised
Service Centre.
8.2 Replacing the lamp
The appliance is equipped with a longlife
LED interior light.
Only service is allowed to replace the
lighting device. Contact your Authorised
Service Centre.
8.3 Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective
door gaskets. Contact the Authorised
Service Centre.
ENGLISH
15
9. INSTALLATION
9.1 Positioning
A
B
Install the appliance in a dry, well
ventilated indoors where the ambient
temperature corresponds to the climate
class indicated on the rating plate of the
appliance.
Climate
class
Ambient temperature
SN
+10°C to + 32°C
N
+16°C to + 32°C
ST
+16°C to + 38°C
T
+16°C to + 43°C
Some functional problems
might occur for some types
of models when operating
outside of that range. The
correct operation can only
be guaranteed within the
specified temperature
range. If you have any
doubts regarding where to
install the appliance, please
turn to the vendor, to our
customer service or to the
nearest Authorised Service
Centre.
9.2 Electrical Connection
CAUTION!
Any electrical work required
to install this appliance
should be carried out by a
qualified electrician or
competent person.
WARNING!
This appliance must be
earthed.
The manufacturer declines
any liability should these
safety measures not be
observed.
The wires in the mains lead are coloured
in accordance with the following code:
C
D
E
• A - green and yellow: Earth
• C - brown: Live
• D - blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either
with the letter “E“ or by the earth
or coloured green and
symbol
yellow.
2. Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3. Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4. Check that no cut, or stray strands of
wire is present and the cord clamp
(E) is secure over the outer sheath.
Make sure the electricity supply
voltage is the same as that indicated
on the appliance rating plate.
5. Switch on the appliance.
The appliance is supplied with a 13 amp
fuse (B). In the event of having to change
the fuse in the plug supplied, a 13 amp
ASTA approved (BS 1362) fuse must be
used.
WARNING!
A cut off plug inserted into a
13 amp socket is a serious
safety (shock) hazard. Ensure
that it is disposed of safely.
16
www.aeg.com
9.3 Ventilation requirements
The airflow behind the appliance must
be sufficient.
5 cm
7. Tighten the lower pin on the
opposite side.
min.
200 cm2
min.
200 cm2
8. Install the lower spacer.
9. Install the door.
10. Refit the pins (B) and the spacers (C)
on the middle hinge on the opposite
side.
11. Tighten the spacer and the upper
pin.
CAUTION!
Refer to the assembly
instructions for the
installation.
9.4 Door reversibility
1. Loosen and remove the upper pin
and the spacer.
2. Remove the upper door.
3. Unscrew the pins (B) and spacers (C).
C
B
C
4. Remove the door.
5. Remove the lower spacer.
6. Loosen the lower pin with a key.
Do a final check to make
sure that:
• All screws are tightened.
• The magnetic seal
adheres to the cabinet.
• The door opens and
closes correctly.
If the ambient temperature
is cold (i.e. in Winter), the
gasket may not fit perfectly
to the cabinet. In that case,
wait for the natural fitting of
the gasket.
In case you do not want to
carry out the above
mentioned operations,
contact the nearest
Authorised Service Centre.
The Authorised Service
specialist will carry out the
reversibility of the doors at
your cost.
9.5 Installing the appliance
CAUTION!
Make sure that the mains
cable can move freely.
1. If necessary cut the adhesive sealing
strip and then apply it to the
appliance as shown in figure.
ENGLISH
x
x
17
Make sure that the distance between
the appliance and the cupboard
front-edge is 44 mm.
The lower hinge cover (in the
accessories bag) makes sure that the
distance between the appliance and
the kitchen furniture is correct.
Make sure that the clearance
between the appliance and the
cupboard is 4 mm.
8. Open the door. Put the lower hinge
cover in position.
2. Drill the hinge cover (A), as shown in
figure.
4 mm
A
A1
3. Apply the covers (A) and (A1) (in the
bag) in to the intermediate hinge
4. Install the appliance in the niche.
5. Push the appliance in the direction of
the arrows (1) until the upper gap
cover stops against the kitchen
furniture.
2
1
44 mm
9. Attach the appliance to the niche
with 4 screws.
I
I
10. Remove the correct part from the
hinge cover (E). Make sure to remove
the part DX, in the case of right
hinge, SX in opposite case.
6. Push the appliance in the direction of
the arrows (2) against the cupboard
on the opposite side of the hinge.
7. Adjust the appliance in the niche.
18
www.aeg.com
H
H
11. Attach the covers (C, D) to the lugs
and the hinge holes.
16. Tighten the screws.
17. Disconnect the parts (Ha), (Hb), (Hc)
and (Hd).
Hb
C
Ha
D
E
E
Hc
Hd
B
12. Install the vent grille (B).
13. Attach the hinge covers (E) to the
hinge.
14. Connect the appliance laterally to
the kitchen furniture sidewall.
15. Loosen the screws in the fixing
brackets (H), move the brackets (H)
18. Install the part (Ha) on the inner side
of the kitchen furniture.
ca. 50 mm
90°
21 mm
90°
ca. 50 mm
21 mm
19. Push the part (Hc) on the part (Ha).
ENGLISH
19
24. Place the small square on the guide
again and fix it with the screws
supplied.
25. Align the kitchen furniture door and
the appliance door by adjusting the
part (Hb).
Ha
Hc
20. Open the appliance door and the
kitchen furniture door at an angle of
90°.
21. Insert the small square (Hb) into
guide (Ha).
22. Put together the appliance door and
the furniture door and mark the
holes.
Hb
26. Press the part (Hd) on the part (Hb).
8 mm
Hb
Ha
Hd
Hb
23. Remove the brackets and mark a
distance of 8 mm from the outer
edge of the door where the nail must
be fitted (K).
8 mm
K
Ha
Do a final check to make sure that:
• All screws are tightened.
• The sealing strip is attached tightly to
the cabinet.
• The door opens and closes correctly.
20
www.aeg.com
10. NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
SSS
RRR
!
HISSS!
OK
UB
BL
SSSRRR!
HISSS!
SSSRRR!
HISSS!
B!
CLICK!
BRRR!
ICK
CL
!
BRRR!
CR
AC
CLICK!
BRRR!
K!
ENGLISH
BLUBB!
CRACK!
BLUBB!
21
CRACK!
11. TECHNICAL INFORMATION
11.1 Technical data
Dimensions of the recess
Height
mm
1850
Width
mm
560
Depth
mm
560
Rising time
Hours
21
Voltage
Volts
230 - 240
Frequency
Hz
50
The technical information is situated in
the rating plate, on the external or
internal side of the appliance and in the
energy label.
12. ENVIRONMENT CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to
recycle waste of electrical and electronic
appliances. Do not dispose appliances
*
marked with the symbol with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
22
www.aeg.com
ENGLISH
23
222372265-A-312015
www.aeg.com/shop
Download PDF

advertising