A92860GNX1
EN User manual
2
www.aeg.com
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DAILY USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HELPFUL HINTS AND TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
WHAT TO DO IF… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
NOISES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you impeccable
performance for many years, with innovative technologies that help make life simpler –
features you might not find on ordinary appliances. Please spend a few minutes reading to get
the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com
Register your product for better service:
www.aeg.com/productregistration
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available.
The information can be found on the rating plate. Model, PNC, Serial Number.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
ENGLISH
1.
3
SAFETY INSTRUCTIONS
In the interest of your safety and to ensure the correct use, before installing
and first using the appliance, read this
user manual carefully, including its hints
and warnings. To avoid unnecessary mistakes and accidents, it is important to
ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these
instructions and make sure that they remain with the appliance if it is moved or
sold, so that everyone using it through
its life will be properly informed on appliance use and safety.
For the safety of life and property keep
the precautions of these user's instructions as the manufacturer is not responsible for damages caused by omission.
1.1 Children and vulnerable
people safety
• This appliance is not intended for use
by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Keep all packaging well away from
children. There is risk of suffocation.
• If you are discarding the appliance
pull the plug out of the socket, cut the
connection cable (as close to the appliance as you can) and remove the
door to prevent playing children to
suffer electric shock or to close themselves into it.
• If this appliance featuring magnetic
door seals is to replace an older appliance having a spring lock (latch) on
the door or lid, be sure to make that
spring lock unusable before you discard the old appliance. This will prevent it from becoming a death trap for
a child.
1.2 General safety
WARNING!
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• The appliance is intended for keeping
foodstuff and/or beverages in a normal household and similar applications such as:
– staff kitchen areas in shops, offices
and other working environments;
– farm houses and by clients in hotels,
motels and other residential type
environments;
– bed and breakfast type environments;
– catering and similar non-retail applications.
• Do not use a mechanical device or any
artificial means to speed up the thawing process.
• Do not use other electrical appliances
(such as ice cream makers) inside of
refrigerating appliances, unless they
are approved for this purpose by the
manufacturer.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is
contained within the refrigerant circuit
of the appliance, a natural gas with a
high level of environmental compatibility, which is nevertheless flammable.
During transportation and installation
of the appliance, be certain that none
of the components of the refrigerant
circuit become damaged.
If the refrigerant circuit should become damaged:
– avoid open flames and sources of
ignition
– thoroughly ventilate the room in
which the appliance is situated
• It is dangerous to alter the specifications or modify this product in any
way. Any damage to the cord may
cause a short-circuit, fire and/or electric shock.
4
www.aeg.com
WARNING!
Any electrical component (power
cord, plug, compressor) must be
replaced by a certified service
agent or qualified service personnel to avoid hazard.
1.
•
•
•
•
Power cord must not be lengthened.
2. Make sure that the power plug is
not squashed or damaged by the
back of the appliance. A squashed
or damaged power plug may
overheat and cause a fire.
3. Make sure that you can come to
the mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose,
do not insert the power plug.
There is a risk of electric shock or
fire.
6. You must not operate the appliance without the lamp cover (if
foreseen) of interior lighting.
This appliance is heavy. Care should
be taken when moving it.
Do not remove nor touch items from
the freezer compartment if your hands
are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
Avoid prolonged exposure of the appliance to direct sunlight.
Bulb lamps (if foreseen) used in this
appliance are special purpose lamps
selected for household appliances use
only. They are not suitable for household room illumination.
1.3 Daily Use
• Do not put hot pot on the plastic parts
in the appliance.
• Do not store flammable gas and liquid
in the appliance, because they may
explode.
• Do not place food products directly
against the air outlet on the rear wall.
(If the appliance is Frost Free)
• Frozen food must not be re-frozen
once it has been thawed out.
• Store pre-packed frozen food in accordance with the frozen food manufacturer's instructions.
• Appliance's manufacturers storage
recommendations should be strictly
adhered to. Refer to relevant instructions.
• Do not place carbonated or fizzy
drinks in the freezer compartment as it
creates pressure on the container,
which may cause it to explode, resulting in damage to the appliance.
• Ice lollies can cause frost burns if consumed straight from the appliance.
1.4 Care and cleaning
• Before maintenance, switch off the appliance and disconnect the mains plug
from the mains socket.
• Do not clean the appliance with metal
objects.
• Do not use sharp objects to remove
frost from the appliance. Use a plastic
scraper.
• Never use a hair drier or other heating
appliances to speed up defrosting. Excessive heat may damage the plastic
interior, and humidity could enter the
electric system making it live.
1.5 Installation
For electrical connection carefully follow the instructions given in
specific paragraphs.
• Unpack the appliance and check if
there are damages on it. Do not connect the appliance if it is damaged.
Report possible damages immediately
to the place you bought it. In that case
retain packing.
• It is advisable to wait at least four
hours before connecting the appliance to allow the oil to flow back in
the compressor.
• Adequate air circulation should be
around the appliance, lacking this
leads to overheating. To achieve sufficient ventilation follow the instructions
relevant to installation.
• Wherever possible the back of the
product should be against a wall to
avoid touching or catching warm parts
(compressor, condenser) to prevent
possible burn.
ENGLISH
• The appliance must not be located
close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.
• Connect to potable water supply only
(If a water connection is foreseen).
5
ozone layer, in either its refrigerant circuit or insulation materials.
The appliance shall not be discarded together with the urban
refuse and rubbish. The insulation foam contains flammable
gases: the appliance shall be disposed according to the applicable regulations to obtain from
your local authorities. Avoid
damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on
this appliance marked by the
are recyclable.
symbol
1.6 Service
• Any electrical work required to do the
servicing of the appliance should be
carried out by a qualified electrician or
competent person.
• This product must be serviced by an
authorized Service Centre, and only
genuine spare parts must be used.
1.7 Environment Protection
This appliance does not contain
gasses which could damage the
2. CONTROL PANEL
1
2
3
11
4
10
5
9
6
7
8
1 Temperature button
2 Display
3 ON/OFF button
4 Minute minder button
5 Light button
6 Night mode button
7 Ice maker ON/OFF button
8 Paddle
9 Rapid ice button
10 ChildLock button.
11 Mode button
It is possible to change predefined
sound of buttons to a loudly one by
pressing together Mode button and
Temperature colder button for some
seconds. Change is reversible.
6
www.aeg.com
2.1 Display
A
H
A)
B)
C)
D)
E)
F)
G)
H)
Timer
Frostmatic mode
Minute minder mode
Temperature indicator
Night mode
Alarm indicator
Ice maker function
ChildLock mode
2.2 Switching on
To switch on the appliance do these
steps:
1. Connect the mains plug to the power socket.
2. Press the ON/OFF button if the display is off.
3. The alarm buzzer could operate after few seconds.
To reset the alarm refer to "High
temperature alarm".
4. If DEMO appears on the display, the
appliance is in demonstration mode.
Refer to "What to do if..." paragraph.
5. The temperature indicators show the
set default temperature.
To select a different set temperature refer to "Temperature regulation".
2.3 Switching off
To switch off the appliance do these
steps:
1. Press the ON/OFF button for 3 seconds.
2. The display switches off.
G
B C
F
3.
D
E
To disconnect the appliance from
the power disconnect the mains
plug from the power socket.
2.4 Temperature regulation
The set temperature of the freezer may
be adjusted by pressing the temperature
button.
Set default temperature:
• -18°C for the freezer
The temperature indicator shows the set
temperature.
The set temperature will be reached
within 24 hours.
After a power failure the set temperature remains stored.
2.5 Ice maker function
The ice maker is switched on at delivery
and starts up automatically when the appliance is connected to water and power
supplies.
To switch on and off the function:
1. Press the Ice maker ON/OFF button
for 3 seconds.
The ice maker icon is shown when the
ice maker is activated.
2.6 ChildLock mode
To lock any possible operation through
the buttons select the ChildLock mode.
To switch on the function:
1. Press the ChildLock button for 3 seconds.
2. The ChildLock mode indicator is
shown.
To switch off the function:
ENGLISH
1.
Press the ChildLock button for 3 seconds.
2. The ChildLock mode indicator goes
off.
2.7 FROSTMATIC mode
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
This function stops automatically after 52
hours.
To switch off the function before its automatic end:
1. Press the Mode button in order to
select an other function or press the
Mode button until you can see none
of the special icons.
The function switches off by selecting a different freezer set
temperature.
2.8 Minute Minder mode
The Minute Minder mode is to be used
to set an acoustic alarm at the preferred
time, useful for example when a recipe
requires to cool down a mixture for a
certain period of time, or when a reminder is needed in order not to forget
the bottles placed in the freezer for fast
cooling.
To switch on the function:
1. Press the Minute Minder button.
The Minute Minder indicator appears.
The Timer shows the set value (30
minutes).
2. Press the Temperature button to
change the Timer set value from 1 to
90 minutes.
3. The Timer indicator is shown (min).
At the end of the countdown the Minute
Minder indicator flashes and an audible
alarm sounds:
1. Remove any drinks contained in the
freezer compartment.
2. Press the Minute Minder button to
switch off the sound and terminate
the function.
It is possible to deactivate the function
at any time during the countdown:
1. Press the Minute Minder button.
7
2.
The Minute Minder indicator goes
off.
It is possible to change the time during
the countdown and at the end by pressing the Temperature button.
2.9 High temperature alarm
Temperature increase in the freezer
compartment (for example due to an
earlier power failure or door is open) is
indicated by:
• flashing the alarm and freezer temperature indicators
• sounding of buzzer.
To reset the alarm:
1. Press any button.
2. The buzzer switches off.
3. The freezer temperature indicator
shows the highest temperature
reached for a few seconds. Then
show again the set temperature.
4. The alarm indicator continue to flash
until the normal conditions are restored.
2.10 Door open alarm
An acoustic alarm will sound if the door
is left open for a few minutes. The door
open alarm conditions are indicated by:
• flashing alarm indicator
• acoustic buzzer.
When normal conditions are restored
(door closed), the alarm will stop.
During the alarm phase, the buzzer can
be switched off by pressing any button.
2.11 Lighting
The ice dispenser lighting illuminates automatically when operated.
2.12 For continuous lighting
Make sure that the ice dispenser is
unlocked.
2. Press the Light button and the lighting goes on.
Brightness is now about 20% until the
dispenser is used.
1.
8
www.aeg.com
2.13 Switch off the lighting
2.15 Dispensing of ice
Make sure that the ice dispenser is
unlocked.
2. Press the Light button and the lighting goes out.
The dispensing of ice start when the
paddle is fully depressed and continues
until the paddle is released.
Stop delivery by removing the container
from the paddle.
1.
2.14 Night mode
This function is used to terminate the
icemaking during the darker period of
the day.
To switch on or off the Night mode:
1. Press the Night mode button.
The Night mode icon is shown when the
Night mode is activated.
2.16 Rapid dispensing of ice
If increased ice dispensing is desired,
makes following:
1. Press the Rapid ice button and hold
it and than push the paddle.
3. DAILY USE
3.1 Freezing fresh food
The freezer compartment is suitable for
freezing fresh food and storing frozen
and deep-frozen food for a long time.
To freeze small amount of fresh foods it
is not necessary to change the present
setting.
To freeze fresh food activate the FROSTMATIC function at least 24 hours before
placing the food to be frozen in the
freezer compartment.
It is possible to place the fresh food to
be frozen in all compartments except
the lowest.
The maximum amount of food that can
be frozen in 24 hours is specified on the
rating plate, a label located on the inside of the appliance.
The freezing process lasts 24 hours: during this period do not add other food to
be frozen.
3.2 Storage of frozen food
When first starting-up or after a period
out of use, before putting the products
in the compartment let the appliance run
at least 2 hours.
The freezer baskets ensure that it is
quick and easy to find the food package
you want. If large quantities of food are
to be stored, remove all drawers except
for the bottom basket which needs to be
in place to provide good air circulation.
On all shelves except for the top shelf it
is possible to place food that protrude
15 mm from the door.
In the event of accidental defrosting, for example due to a
power failure, if the power has
been off for longer that the value
shown in the technical characteristics chart under "rising time",
the defrosted food must be consumed quickly or cooked immediately and then re-frozen (after
cooling).
3.3 Thawing
Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available
for this operation.
Small pieces may even be cooked still
frozen, directly from the freezer: in this
case, cooking will take longer.
ENGLISH
9
3.4 Removing the ice container
The ice container can be removed.
1. Tilt up and pull the ice container
outwards to removal.
When the ice container is pulled out,
this stops all the functions of the ice
machine.
2. When refitting (if necessary) the ice
container feed screw should be positioned against the rear flange.
2
1
3.5 Shelf above ice maker
The shelf above the ice maker
cannot be removed.
10 www.aeg.com
3.6 Removal of freezing baskets and glass shelves from the
freezer
2
1
The appliance is equipped with shelf
stops to secure the shelves.
The shelves must be lifted up (1) on each
side and than pulled outwards (2).
1
1
2
The glass shelves equipped with expander rollers are secured with locking
pins.
To remove them proceed as follow:
1. Use a screwdriver to loosen the locking pin on each side on the expander roller.
2. Then pull out both locking pin (1).
3. Then pull the glass shelf outwards
(2).
1
1
1
Some of the freezing baskets have a limit
stop to prevent their accidental removal
or falling out. At the time of its removal
from the freezer, pull the basket towards
yourself and, upon reaching the end
point, remove the basket by tilting its
front upwards
At the time of putting it back, slightly lift
the front of the basket to insert it into
the freezer.
Once you are over the end points, push
the basket back in their position.
2
ENGLISH
11
3.7 Cleaning the interior
Before using the appliance for the first
time, wash the interior and all internal
accessories with lukewarm water and
some neutral soap so as to remove the
typical smell of a brand-new product,
then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
Check that the drain hose at the rear of
the cabinet discharges into the drip tray
4. HELPFUL HINTS AND TIPS
4.1 Hints for freezing
To help you make the most of the freezing process, here are some important
hints:
• the maximum quantity of food which
can be frozen in 24 hrs. is shown on
the rating plate;
• the freezing process takes 24 hours.
No further food to be frozen should
be added during this period;
• only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
• prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
• wrap up the food in aluminium foil or
polythene and make sure that the
packages are airtight;
• do not allow fresh, unfrozen food to
touch food which is already frozen,
thus avoiding a rise in temperature of
the latter;
• lean foods store better and longer
than fatty ones; salt reduces the storage life of food;
• water ices, if consumed immediately
after removal from the freezer compartment, can possibly cause the skin
to be freeze burnt;
• it is advisable to show the freezing in
date on each individual pack to enable
you to keep tab of the storage time.
4.2 Hints for storage of frozen
food
To obtain the best performance from
this appliance, you should:
• make sure that the commercially frozen foodstuffs were adequately stored
by the retailer;
• be sure that frozen foodstuffs are
transferred from the foodstore to the
freezer in the shortest possible time;
• not open the door frequently or leave
it open longer than absolutely necessary;
• once defrosted, food deteriorates rapidly and cannot be refrozen;
• do not exceed the storage period indicated by the food manufacturer.
12 www.aeg.com
5. CARE AND CLEANING
CAUTION!
Unplug the appliance before carrying out any maintenance operation.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must
therefore only be carried out by
authorized technicians.
5.1 Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with
lukewarm water and some neutral
soap.
• regularly check the door seals and
wipe clean to ensure they are clean
and free from debris.
• rinse and dry thoroughly.
Do not pull, move or damage
any pipes and/or cables inside
the cabinet.
Never use detergents, abrasive
powders, highly perfumed cleaning products or wax polishes to
clean the interior as this will damage the surface and leave a
strong odor.
Clean the condenser (black grill) and the
compressor at the back of the appliance
with a brush. This operation will improve
the performance of the appliance and
save energy consumption.
Take care of not to damage the
cooling system.
When moving the cabinet, lift it
by the front edge to avoid
scratching the floor.
Many proprietary kitchen surface cleaners contain chemicals that can attack/
damage the plastics used in this appliance. For this reason use a soft cloth
rinsed in warm water and neutral soap
emulsion for cleaning external surfaces.
Do not use detergents or abrasive paste as these will damage
the paint, or stainless steel anti
finger print coating.
After cleaning, reconnect the equipment
to the mains supply.
5.2 Cleaning the ice maker
When necessary, clean the surfaces of
the dispenser and the ice container that
are accessible from the outside, using
only a soft cloth and warm water.
Ensure that the ice container is thoroughly dry before being refitted.
Do not use detergents or abrasive paste.
5.3 Defrosting of the freezer
The freezer compartment of this model,
on the other hand, is a "no frost" type.
This means that there is no buildup of
frost when it is in operation, neither on
the internal walls nor on the foods.
The absence of frost is due to the continuous circulation of cold air inside the
compartment, driven by an automatically
controlled fan.
5.4 Periods of non-operation
When the appliance is not in use for
long periods, take the following precautions:
1. Switch off the ice maker
2. Turn off the water connection
3. Empty the ice container
4. Disconnect the appliance from electricity supply
5. Remove all food
6. Clean the appliance and all accessories
7. Leave the door/doors open to prevent unpleasant smells.
When the ice maker starts again, do not
use ice produced during the first day to
ensure fresh taste.
ENGLISH
13
If the cabinet will be kept on, ask
somebody to check it once in a
while to prevent the food inside
from spoiling in case of a power
failure.
5.5 Cleaning the ventilation grille
The ventilation grille can be removed for
washing.
Make sure the door is open and then:
• Loosen the upper edge of the grille by
pulling outward/downward.
• Pull the grille straight out to completely remove it.
• Vacuum clean under the cabinet.
6. WHAT TO DO IF…
During operation of the appliance some
smaller but annoying trouble can often
occur, which does not require calling a
technician out. In the following chart information is given about them to avoid
unnecessary charges on service.
The operation of the appliance
goes with certain sounds (compressor and circulating sound).
This not means a trouble, but a
normal operation.
The appliance operates discontinuously, so the stopping of
compressor does not mean being no current. That is why you
must not touch the electrical
parts of the appliance before
breaking the circuit.
Problem
Possible cause
Solution
The appliance is
noisy.
The appliance is not supported properly.
Check if the appliance
stands stable (all feet and
wheels should be on the
floor). Refer to "Levelling".
A rattling noise.
The ice being stirred to
prevent it from freezing
together.
No measure necessary,
this sound is normal.
As an alternative, refer to
"To activate the night
mode"
The buzzer sounds.
The temperature in the
The Alarm icon flash- freezer is too high.
ing.
Refer to "High Temperature Alarm".
The door is not closed
correctly.
Refer to "Door open
alarm".
14 www.aeg.com
Problem
Possible cause
Solution
Upper or lower
square is shown in
the temperature display.
An error has occurred in
measuring the temperature.
Call your service representative (the cooling system
will continue to keep food
products cold, but temperature adjustment will not
be possible).
The compressor runs The Temperature regula- Set a warmer temperature.
continuously.
tor may be set incorrectly.
There is too much
frost and ice.
The door is not closed
correctly.
Refer to "Closing the
door".
The door has been
opened too frequently.
Do not keep the door
open longer than necessary.
The food temperature is
too warm.
Let the food temperature
decrease to room temperature before storage.
The room temperature is
too warm.
Decrease the room temperature.
The door is not closed
correctly.
Refer to "Closing the
door".
The door gasket is deformed or dirty.
Refer to "Closing the
door".
The temperature in
the appliance is too
cold.
The Temperature regula- Set a warmer temperature.
tor may be set incorrectly.
The temperature in
the appliance is too
warm.
The Temperature regula- Set a colder temperature.
tor may be set incorrectly.
The temperature in
the freezer is too
warm.
The appliance does
not operate.
The door is not closed
correctly.
Refer to "Closing the
door".
The food temperature is
too warm.
Let the food temperature
decrease to room temperature before storage.
Food is too near to each
other.
Store food so that there is
cold air circulation.
Large quantities of food
to be frozen were put in
at the same time.
Insert smaller quantities of
food to be frozen at the
same time.
The appliance is switched Switch on the appliance.
off.
The mains plug is not
connected to the mains
socket correctly.
Connect the mains plug to
the mains socket correctly.
ENGLISH
Problem
15
Possible cause
Solution
The appliance has no
power. There is no voltage in the mains socket.
Connect another electrical
appliance to the mains
socket. Check fuse. Contact a qualified electrician.
No ice.
The ice maker is not
switched on.
Refer to "Ice maker function".
E1 flashes in the
temperature display
No water supply.
Carry out the necessary
measures on the water
supply. Press any button to
reset the Alarm.
E2 flashes in the
temperature display
The ice channel in the
door is blocked.
Remove the obstacle.
Press any button to reset
the Alarm.
E3 flashes in the
temperature display
The ice maker is defective.
Contact service.
E5 flashes in the
temperature display
The ice dispenser is defective.
Contact service.
The lamp does not
work.
The lamp is defective.
Refer to "Replacing the
lamp".
The door has been open
to long.
Close the door.
Door interferes with
ventilation grill.
The appliance is not levelled.
Refer to "Levelling".
Misaligned door.
The appliance is not levelled.
Refer to "Levelling".
DEMO appears on
the Display
The appliance is in demonstration mode (DEMO)
Keep pressed approximately 10 sec the Mode
button since a long sound
of buzzer is heard and the
Display shut off for a short
while: appliance start
works regularly.
As much as the advice does not lead to result, call the nearest brand-mark service.
6.1 Replacing the lamp
The appliance is equipped with a longlife LED interior light.
Only service is allowed to replace the
lighting device. Contact your Service
Center .
6.2 Closing the door
1.
Clean the door gaskets.
2.
If necessary, adjust the door. Refer
to "Installation".
3. If necessary, replace the defective
door gaskets. Contact the Service
Center.
16 www.aeg.com
7. INSTALLATION
WARNING!
Read the "Safety Information"
carefully for your safety and correct operation of the appliance
before installing the appliance.
7.1 Positioning
Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Climate
class
Ambient temperature
SN
+10°C to + 32°C
N
+16°C to + 32°C
ST
+16°C to + 38°C
T
+16°C to + 43°C
7.2 Location
50 mm
7.3 Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating
plate correspond to your domestic power supply.
The appliance must be earthed. The
power supply cable plug is provided
with a contact for this purpose. If the do-
To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the
wall unit must be at least 40 mm. Ideally,
however, the appliance should not be
positioned below overhanging wall units.
The ventilation space can be:
• directly above the appliance
• behind and above the top cupboard.
In this case, the space behind the top
cupboard must be at least 50 mm
deep.
mestic power supply socket is not earthed, connect the appliance to a separate
earth in compliance with current regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if the above safety precautions are
not observed.
This appliance complies with the E.E.C.
Directives.
ENGLISH
17
7.4 Removing the transport support
Your appliance is equipped with transport support to secure the door during
transportation.
To remove them do these steps:
• Open the door.
• Remove the transport support from
the door sides.
• Remove the transport support from
the lower hinge (some models).
3
2
Some models are fitted with a silencing pad under the cabinet.
Do not remove this pad.
7.5 Rear spacers
• Install the spacers provided within the
accessory bag as shown in the figure.
• Install the spacers on the brackets of
the condenser (black grill) at the back
of the appliance.
7.6 Connecting the water
hose.
Water supply should be provided with a
tap and 3/4" male connector within 1,5
m from the appliance.
This work is to be carried out by a skilled
plumber.
There are different type-approved taps
and tap assemblies on the market.
The water hose must not be cracked,
squeezed or put in tight bends.
If this appliance has been purchased together with the corresponding fridge the
installation should be conducted in such
a way that both appliances share the
safety valve supplied with the fridge.
Should this appliance instead have been
purchased as a single installation or together with an appliance without water
connection, it is strongly recommended
that a safety valve (1504516–00/4) is installed. This item can be ordered via
www.electrolux.com.
Before the appliance is placed in its final
location, ensure that the water connection has been correctly carried out and
that there is no leakage at the connection to the water tap.
Tighten the connections by hand only.
18 www.aeg.com
Make sure that the gasket is properly
positioned in the connector.
We recommend that the appliance is
placed on a "run-off" mat intended for
refrigerators and freezers, which makes it
easier to detect possible leakage.
7.7 Levelling
When placing the appliance ensure that
it stands level. If necessary adjust the
feet using the adjustment spanner supplied.
7.8 Starting the ice maker for
the first time.
Do not use ice produced during the first
day to ensure fresh taste.
Ensure proper connection to the water
supply, refer to "Connecting the water
hose".
1. Open the tap on the water connection.
2. Start the freezer and the ice maker
starts automatically.
It will start filling water when the temperature is sufficiently low.
7.9 Door reversibility
In case you want to change the opening
direction of the door, contact the nearest After Sales Service Force. The After
Sales Service specialist will carry out the
reversibility of the doors at your cost.
8. NOISES
There are some sounds during normal
running (compressor, refrigerant circulation).
SSS
RRR
!
HISSS!
OK
U
BL
BB
CL
ICK
!
BRRR!
!
CR
AC
K!
ENGLISH
SSSRRR!
HISSS!
BLUBB!
SSSRRR!
HISSS!
BLUBB!
CLICK!
BRRR!
CRACK!
19
CLICK!
BRRR!
CRACK!
20 www.aeg.com
9. TECHNICAL DATA
Dimension
Height
1800 mm
Width
595 mm
Depth
650 mm
Rising Time
10 h
Voltage
230 V
Frequency
50 Hz
The technical information are situated in
the rating plate on the internal left side
of the appliance and in the energy label.
Water pressure range
The water pressure must be at least 1 bar
(100kPa)
Consult your installer if water
pressure is less than 1 bar.
Highest allowed water pressure 10 bar
(1000kPa)
If water pressure exceeds 10 bar
a reduction valve must be fitted
(available from your specialist
shop).
• Do not connect the appliance
in spaces where ambient temperature can decrease to below freezing.
• The appliance may only be
connected to drinking water
supplies.
• The appliance may only be
connected to cold water supplies.
10. ENVIRONMENT CONCERNS
Recycle the materials with the
symbol . Put the packaging in
applicable containers to recycle it.
Help protect the environment and
human health and to recycle waste
of electrical and electronic
appliances. Do not dispose
appliances marked with the symbol
with the household waste. Return the
product to your local recycling
facility or contact your municipal
office.
ENGLISH
21
22 www.aeg.com
ENGLISH
23
298376973-B-162013
www.aeg.com/shop
Download PDF

advertising