Zanussi | Z55BGS | User manual | ZANUSSI Z55BGS User Manual

ZANUSSI Z55BGS User Manual
English
THE GUARANTEE
IMPORTANT
This new appliance is easy to use, however, to
obtain the best results, it is important to read this
booklet and to follow all the instructions before
using it for the first time.
The booklet contains the necessary information
regarding installation, use and maintenance, as
well as giving useful advice.
Appliance
Class 1 and
Class 2
Your new cooker is covered by guarantee.
You will find the guarantee certificate enclosed. If you
are missing anything contact your retailer, giving the
date of purchase, model, and the registration number
which is printed on the identification plate.
We ask you to bear in mind that for the guarantee to be
operated, it is necessary to fill in and send the larger
part of the guarantee to Zanussi Technical Assistance
& Service within 8 days of purchase, so that we can
provide registration.
We advise you that the smaller part of the certificate,
as well as your receipt and proof of purchase, should
be shown when required to personnel of Zanussi
Technical Assistance & Service.
Without following this procedure, the repair personnel
will have to charge you more for the repair.
Sub-Class 1
Category:
Voltage tension:
III 1a 2H3+
230 V ~ 50 Hz
MANUFACTURER:
ELECTROLUX ZANUSSI S.p.A.
Viale Bologna 298
47100 FORLÌ (Italy)
This appliance complies with the following E.E.C. Directives:
• 73/23 - 90/683 (Low Voltage Directive);
• 89/336 (Electromagnetical Compatibility Directive);
• 90/396 (Gas Appliance Directive);
• 93/68 (General Directives);
and subsequent modifications.
These instructions are only valid for those countries whose identication symbols are shown
on the cover of the instruction brochure and on the appliance itself.
29
WARNINGS - GAS AND MIXED-FUEL COOKERS
It is very important that this instruction book should be kept safely for future consultation. Il the
should be sold or given toanother person, please ensure that the booklet goes together with it,
so that the new owner can know of the functions of the machine and also be aware of the
warnings.
This warnings has been given for the safety of you and others, We therefore ask you to carefully
read the procedures of installing and using this cooker.
This appliance has been designed for use by adults.
Take care, therefore, that children do not attempt to play
with it.
The work of installation must be carried out by
competent and qualified installers according to the
regulations in force.
Any modifications to the domestic electrical mains
which may be necessary for the installation of the
appliance should be carried out only by competent
personnel.
In case of repairs contact an authorized Technical
Assistance Centre and insist on original spareparts.
It is dangerous to modify, or attempt to modify, the
characteristics of this appliance.
Unstable or deformed pans should not be placed on the
burners or plates in order to avoid accidents caused by
upsetting or boiling over.
Particular care should be taken when cooking with oil or
fat.
The appliance remains hot for a long time after being
switched off. Supervise children at all times when in use
paying attention that they do not touch surfaces or
remain in the vicinity of the appliance when in use or
when not completely cooled.
If the appliance is fitted with a cover, its function is to
protect the surface from dust when closed and to accumulate splashes of grease when open.
Do not use for other purposes.
Always clean the cover before closing.
Leave the burners and/or plates to cool before closing.
All the covers, in plate glass or enamel, are removable
to facilitate cleaning.
Let the burners and/or plates cool before closing.
Always insert the dripping pan when using the grill or
when cooking meat on the grill. Pour a little water into
the dripping pan to avoid grease burning and creating
unpleasant smells.
Always use oven gloves to remove dishes from the oven.
During the first minutes of use, the thermal insulation of
the oven, and residual grease from manufacture, produce smoke and disagreeable smells.
On first use, we advise heating the oven, empty, for
approximately 45 minutes.
Then leave to cool and clean the inside of the oven with
hot water and a mild detergent.
The accessories (grill and dripping pan) should be
washed before using for the first time.
30
Take care when using cleaning products in spray form:
never direct the spray onto the resistance or the
thermostat bulb.
If, when placing food in the oven, or when removing it, a
large quantity of oil, juice, etc. spills onto the bottom of
the oven, re-clean before starting to cook to avoid
unpleasant smoke and also the possibility of these
substances catching fire.
Ensure that air can circulate around the gas appliance.
Poor ventilation can produce a lack of oxygen.
WARNING: The use of a gas cooking appliance
produces heat and humidity in the room in which it is
installed. Ensure good ventilation of the room keeping
natural ventilation openings clear or installing an
extractor hood with a discharge tube.
In case of doubt ask installer for advice.
For reasons of hygiene and safety this appliance must
always be kept clean. A build up of grease or other food
can cause fires.
This product is intended for the cooking of food and must
not be used for other purposes.
Avoid installation of the cooker near inflammable
material (e.g. curtains, tea towels, etc.).
Supply the appliance with the type of gas stamped on
the relevant adhesive label situated in the immediate
vicinity of the gas connection tube.
The gas oven becomes hot with the movement of air.
The holes on the bottom of the oven must never be
obstructed. Do not cover the sides of the oven with
aluminium foil, in particular the lower part of the opening.
The appliance is heavy, move it carefully.
Before maintenance and cleaning disconnect the
appliance and allow to cool.
To facilitate ignition, light the burners before
placing pans on the grill.
After having lit the burners check that the flame is
regular.
Always lower the flame or turn it off before removing the
pan.
Ensure that the oven grills are inserted correctly (see
instructions).
If there are self-cleaning panels they should only be
cleaned with soap and water (see cleaning instructions).
Only heat-resistant plates may be placed in the drawer
situated under the oven.
Do not put combustible materials there.
In case of repairs, do not attempt to correct yourself.
Repairs carried out by unqualified persons can cause
damage.
INDEX
Warning
Dimensions of the unit
Instructions for the user
Installation
Use
Gas oven
Turnspit
Electric oven
Programming of cooking
Advice for use of oven
Tables of Cooking time
Maintenance
Instructions for installation
Gas connection
Adaption to different types of gas
Electrical connection
What to do if...
Technical Assistance and Spare Parts
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
Pag.
30
32
33
33
33
35
36
37
40
41
44-45
46
47
48
50
53
54
54
During cooking on the grill or in the oven, the unit is
kept at a high temperature in relation to the plate
glass door and adjacent parts. Take care therefore,
that children do not play near it.
When connecting household appliances to a plug
near the unit, ensure that they are kept away from
the flame and the oven door.
DOOR KIT FOR ELECTRIC OVEN code number 35791
Our appliances are in conformity with the EUROPEANS SAFETY REGULATIONS.
In order to further protect children from the heat coming from the oven door a special kit, which can be easily applied to
the appliance, is available.
You can buy the kit in our CUSTOMER SERVICE CENTRES; it can be requested stating the number of PROD. NO.
shown on the working platelet.
Instructions for the installationn are enclosed in the packaging.
31
DIMENSIONS OF THE UNIT
Type
Height
Width
Depth
1
850
500
500
2
850
600
500
3
850
600
550*
6
850
600
600
H
D
W
Type
Height
Width
Depth
5
850
900
550
6
850
900
600*
H
W
D
The total absorbing power and other technical specifications are shown on the rating plate in the oven
floor.
* Models with splash back
32
INSTRUCTIONS FOR THE USER
INSTALLATION
It is important that all operations are carried out by
qualified personnel, in the normal manner.
The specific instructions are describred in the chapter
on installation.
Before using the unit, take off the special protective layer
which protects the stainless steel and anodyne tin parts.
The thermic insulation and the residue of oil from work,
can produce unpleasant smells during the first minut of
use. We suggest that the oven is warmed for 45 minutes
at maximum temperature on its first use.
If after a few attempts the burner does not ignite, check
that the baffle and its cap are correctly positioned.
To interrupt the supply of gas, turn the knob in a
clockwise direction to the position " ".
In case the burner flame accidentally goes out, close the
command knob and try to ignite again after at least 1
minute.
During cooking, when using fats or oils, take
particular care as they can, when over-heated, selfignite.
USE
Control knobs on the cooke
The knobs for using the gas cooker are found on the
control panel.
The regulation knobs hould be turned in anti-clockwise
direction until the small flame symbol, and vice-versa for
the larger symbol.
l
No gas supply
Maximum gas supply
Minimum gas supply
This appliance is equipped with a safety-valve. In case
of extinction of the flame, this device will operate,
stopping gas supply (ex. overflowing, draughts).
Fig. 1
Table 1
IGNITION OF HOB BURNERS
To ignite a burner, before positioning the saucepan,
approach with a flame (in models with electric ignition,
use the appropriate switch marked by a small start),
push the corresponding knob in completely and turn in
an anticlockwise direction to the maximum position,
keep the knob pressed for approximately 5 seconds
until the security valve automatically maintains the flame
alight; upon ignition regulate the flame as required.
Table of minimum and maximum diameters of recipients
to be placed on burners.
Burner
min diam
max diam
Rapid (large)
ø 160 mm
ø 260 mm
S/Rapid (medium)
ø 120 mm
ø 220 mm
Auxiliary (small)
ø 80 mm
ø 160 mm
Fish kettle burner
120 x 270
210 x 380
Fig. 1
33
POTTERY
POTTERY
Remember that a wide-bottomed pan allows a faster
cooking than a narrow one.
Always use pots which properly fit what you have to
cook.
Particularly make sure that the pans are not too small
for liquids, since these could easily overflow.
Moreover, the pans should not be too large for a faster
cooking. In fact, grease and juices may spread on the
bottom and burn easily.
It is better to use non-openable moulds for baking cakes.
In fact, an openable mould lets juices and sugar leak
through, falling on the bottom of the oven and
consequently burning on the bottom of the baking tray,
making cleaning difficult.
Avoid putting plastic-handled pans in the oven as they
are not heat-proof.
You should use oans with the right diameter to fit the
burner, in order to make the most out of it, thus reducing
gas consumption as in Fig. 1.
It is also advisable to cover any boiling casserole and,
as soon as the liquid starts boiling, lower the flame
enough to keep the boiling point.
HOTPLATES
BARBECUE IN LAVIC ROCK
To grill meat, fish, sausages, etc. some models are
supplied with an electric barbecue.
A 12 position switch regulates the temperature of the
heating element permitting optimization of cooking.
The packet of lavic rock supplied serves to absorb fats
from food melted by heat.
To put the lavic rock in the container proceed as follows:
- remove the grill above the container as illustrated in figure 2;
- lift the electrical resistance upwards as illustrated in
figure 2;
- open the packet of lavic rock and fill the bottom of the
container evenly.
The lavic rock must be replaced when it becomes black.
It is important to replace it fairly regularly and with good
quality material, otherwise it could produce smoke and
smells.
Lavic rock is easily obtainable in hardware or household
equipment stores, etc. Lavic rock can, however, be
regenerated and thus re-used by exposing it to a lighted
flame.
To remove the lavic rock from the container it is sufficient
simply to pull the central handle of the container upwards
and then remove from the opening.
Saucepans suitable for use on solid plate hobs should
have several characteristics:
They should be fairly heavy duty.
They should fit the heat area exactly, or be slightly larger
for efficient use, NEVER smaller.
They should have a flat base to ensure good contact with
the plate.
This is particularly important when using pans for high
temperature frying or pressure cooking.
Ensure pans are large enough to avoid liquids being spilt
onto the plates.
Never leave the plates on without a pan on them or with
an empty pan on them.
To obtain the best results, regarding kitchens
equipped with hotplates and central grill,
remember to remove the grill situated above the
hotplate; sothat damagings and overheatings will
be avoided.
In models supplied with a cover, if the cover is in
glass it should not be closed when the burners are
still hot as it could splinter.
This appliance conforms to EEC directive no. 87/308
of 2/6/87 concerning the suppression of radioelectric interferences.
34
FO 0151
Fig. 2
GAS OVEN
Ignition:
open the oven door and hold a flame to the right-hand
side hole as shown in fig. 3; press the oven knob and
turn anti-clockwise until the maximum temperature
position is reached; press in the oven knob for
approximately 5 seconds until the safety valve
automatically keeps the oven burner lit. If the burner
does not light first time, repeat the operation keeping the
knob pressed in slightly longer. Once the oven has been
lit, adjust the flame as required.
For automatic ignition:
Open the oven door and push and turn the appropriate
switch in an anti-clockwise direction to the maximum
temperature position (fig. 6); at the same time push the
relevant button marked with a small spark. Upon ignition
keep the switch pushed in for approximately 5 seconds.
Ignition of the oven burner must be carried out with
the oven door open.
FO 1079
Fig. 3
When cooking with the oven or grill, the cover
must be kept open to avoid over-heating.
In kitchens equipped with thermometer after a few
minutes control the indication of thermometer and operate on the oven knob (Fig. 5) to choose the temperature desired.
In kitchens equipped with thermostat (Fig. 6), to adjust
automatically the flame, after a few minutes turn the
knob to the position corresponding to the temperature
desired.
The oven is equipped with an enamelled dripping-pan
which serves to collect the juices which drip from the
meat on the grill or on the spit, and a grill for the cooking
of foods on the grill or in a pan.
In models provided with oven grills with a position catch
(fig. 4) and when cooking on the grill or on the spit, you
are advised to fit the dripping-pan (A-fig. 4) in the guides
beneath the grill (B-fig. 4) to avoid dirtying the oven.
When you have to position the dripping-pan above the
oven grill during cooking, position it as shown in fig. 4.
Fig. 4
FO 0190
140
16
0
240
Fig. 5
FO 1096
200
FO 1101
Fig. 6
35
TURNSPIT
Some models are equipped with a turnspit (fig.7).
b
c
For correct use, proceed as follows:
•
slide the spit into the food to be cooked and secure
well;
•
place the spit on the support and slide the whole into
the third runner from the bottom of the oven cavity;
•
insert the end of the spit into the rotisserie motor
housing (the orifice in the wall at the back of the
oven);
•
remove the spit handle;
•
turn the oven knob to the grill position or, when
required for some models, turn on the motor by
means of the appropriate switch placed on the
control panel.
a
a)
b)
c)
d)
d
Removable spit handle
Spit
Spit forks
Spit support
Fig. 7
4
3
2
1
When cooking with the rotisserie you are advised
to leave the oven door half open and to fit the knob
protection shield as shown in fig. 8-9.
FO 0329
FO 0375
36
Fig. 8
FO 2124
Fig. 9
ELECTRIC OVEN
Control knob (fig. 6)
It makes it possible to choose the most appropriate temperature and to select the elements radiating heat one
by one.
Under these conditions the temperature will never
exceed about 200°C in the bottom heat position
180°C in the top heat position
regulated by the thermostat.
and
and it will not he
Explanation of symbols:
Oven in off position
Oven light
50-max Temperature
To select the temperature turn the knob clockwise until
the pointer in an the figure indicating the desired temperature included hetween 50°C and max.
The temperature will be kept constant by the
thermostat.
If you want more heat coming from the bottom or more
heat coming from the top turn the knob so as to place
the pointer on the symbol
heat).
(bottom heat) or
15
0
Bottom heat
Top heat
Grill
100 5
0
0
FO 1095
200
0
Fig. 10
(top
ELECTRIC STATIC GRILL
In the models with electric oven turn the knob so as to
.
place the pointer on the symbol
In the models with gas oven press and turn the knob
clockwise until the stop position is reached
, at the
same time the grill light will come on.
Place the dripping pan under the wire shelf so as to
prevent fat from dripping on the bottom of the oven.
In the models with gas oven and electric oven it
is necessary, while the grill is in function, to leave
the door half-open and to put the protective screen
to the knob (fig. 8-9).
37
ELECTRIC OVEN (5 FUNCTIONS)
Command selection switch (Fig. 11) and thermostat
(Fig. 12).
Permit choice of heat most suitble for different types of
cooking by inserting suitable heating elements and
regulating the temperature to the degree required.
The oven light stays lit in all selector positions.
Grilling
Symbol meanings:
Turn the selector switch to position
turn the
thermostat switch until it coincides with the temperature required.
Turn the selection switch to
turn the thermostat
switch until it coincides with the temperature required.
Cooking with the lower element
Cooking by convection
upper and lower heating elements
grill element
lower heating element
turn the
Turn the selector switch to position
thermostat switch until it coincides with the temperature required.
upper and lower heating element + fan
Defreezing
defreezing
Traditional cooking
Turn the selector switch until the mark coincides with
Turn the selector switch to position .
In this way the motorized fan is inserted. By moving the
cold air inside the oven this permits frozen foods to be
quickly defreezed.
and the thermostat until it coincides with
the position
the temperature required.
With the selector switch (Fig. 11) in position turn the
oven thermostat switch (Fig. 12) to position « »
In models having 5 function ovens of the type
indicated above, when using the grill the oven door
must remain half-open and the switch protection
shield (fig. 8-9) must be in position.
100
50
0
150
38
Fig. 11
FO 1098
0
20
FO 1099
Fig. 12
In order to avoid over-heating when cooking with
the oven or grill, always keep the appliance cover
open.
The oven is supplied with an enamel dripping pan to
collect cooking juices from meat on the grill and a grill
for the cooking of food on the grill or in baking tins.
In models supplied with an oven grill with automatic
switch off (Fig. 13) and in the case of grilling, to avoid
dirtying the oven excessively, it is advisable to insert the
dripping pan (A - Fig. 13) in the relevant guide under the
grill (B - Fig. 13).
When cooking with the dripping pan under the oven grill,
position as shown in Fig. 13.
FO 0190
Thermometer
Some cookers are supplied with a thermometer to
control the oven temperature.
In some models this thermometer signals increase in
temperature by showing a red-coloured strip on the oven
door glass, in others a red-coloured bimetallic sign
positioned on the oven door signals increase in temperature inside the oven.
Mechanical timer
The timer can be regulated for a maximum period of one
hour. The regulation switch (fig. 14) must be turned in a
clockwise direction to the 60 minute position and then
in an anti-clockwise direction to the time required.
At the end of the time selected an acoustic signal
intervenes which stops automatically. The timer does
not interrupt the operation of the oven upon action of the
acoustic signal.
Fig. 13
Oven light switch
Permits the oven illumination light to be switched on.
Operational pilot light
When lit shows the insertion of one or more heating
elements.
FO 0192
Fig. 14
Oven thermostat pilot light
Switches off when the oven reaches selected temperature and re-lights every time the thermostat intervenes
to stabilize the temperature.
Barbecue pilot light
In cookers supplied, shows insertion of heating element;
is switched off by turning the switch to position 0.
Grill pilot light
In cookers with gas ovens, shows insertion of the electric
grills.
39
PROGRAMMING OF COOKING
End of cooking digital programmer (Fig. 15)
Manual operation
In some models it has the function of switching off the
oven at the end of pre-selected cooking time.
The programmer has an electric clock which indicates
the time of day and a timer with an acoustic signal.
Fig. 15 illustrates the programmer’s commands;
switches A and B carry out the necessary regulations
foreseen, as follows:
The oven can be used normally, i.e. without any
programme. In such case switch B of the programmer
should be turned in a clockwise direction until symbol il
funzionamento manuale del forno (posizione ).
coincides with the mark on face C.
Switch A
Prearrange the food to be cooked; turn switch B in a
clockwise direction and preset the minutes presumed for
the end of cooking on switch C;
turn the oven switch to the temperature required.
At the end of the established time an acoustic signal
intervenes; to switch off it is sufficient to turn switch B
to symbol
visible on face C, corresponding to the
mark on the face itself.
Turned in a clockwise direction permits the time shown
on the digital clock to be corrected (at the time of
installation, electricity cuts, to advance or turn back,
etc.).
Switch B
Turned in a clockwise direction sets:
the length of cooking time (max. 210 minutes);
interruption of the acoustic signal (position
);
manual operation (position ).
The above signals appear on face C.
C
FO 0158
40
A B
Fig. 15
Programmed operation of the oven
SUGGESTIONS FOR GAS BURNERS
Start cooking with a big flame by turning theknob to .
Then adjust the flame as necessary.
The outside of the flame is much hotter than its inside
(nucleus). Accordingly the top of the flame should lick
the bottom of the pan. Excessive flames mean a waste
of gas.
In contrast with electric grids, gas burners do not require
flat-bottomed pans.
The flames lick the bottom and spread the heat all over
the surface.
No special pans are required for gas burners. However,
thinwalled pans transmit the heat to the food more
quickly than thick-walled ones.
Since heat doesn't spread evenly on the pan's bottom,
the food may only be partially heated. Consequently it
is advisable to stir the food many times.
A thick pan bottom prevents partial overheating as it
allows sufficient thermic compensation.
Avoid very small pans. Wide and shallow pans are more
suitable than narrow and deep ones as they allow a
faster heating. Cooking is not quickened by placing
narrow pans on wide burners. The result is just a waste
of gas. For a proper usage, place small pans on small
burners and large pans on large burners.
Remember to cover pans to reduce gas consumption.
SUGGESTIONS FOR OPERATING OF OVEN
Traditional cooking
Heat derives from the top and the bottom, it is therefore
preferable to use the central guides. If cooking requires
more heat from the bottom or the top, use the upper or
lower guides.
Convection cooking
Heat is transmitted to food through pre-heated air and is
forcibly circulated inside the oven by a fan positioned on
the back of the oven itself. In this way heat quickly and
uniformly reaches all parts of the oven thus cooking
various foods placed on more than one shelf.
With this type of cooking the elimination of humidity from
the air and a drier environment prevent the transmission
and mixture of smells and tastes.
The possibility of cooking on more than one shelf
consents many various dishes to be prepared at the
same time and up to three trays of biscuits or minipizzas to be consumed immediately or to be frozen. The
oven can, however, be used for cooking on only one
shelf. In such case use the lower guides in order to
observe cooking better.
Furthermore, this oven is especially convenient for quick
defreezing, sterilizing preserves, homemade fruit in
syrup and finally to dry mushrooms or fruit.
Cooking with the multi-function oven
With this type of oven it is possible to carry out cooking
traditionally, by convection, by jets of heat and by grill;
it therefore allows cooking to be optimized.
ADVICE FOR USE OF THE TRADITIONAL
OVEN (GAS OR ELECTRIC)
For the cooking of cakes
Pre-heat the oven , unless indicated differently, for at
least 10 minutes before use. Do not open the oven door
when cooking dishes which must raise (e.g. raised
pastries and soufflés); the jet of cold air would block the
raising process. To check if cakes are cooked, insert a
toothpick into the mixture; if it comes out clean the cake
is ready. Wait until at least 3/4 of the cooking time has
passed before doing this check.
As a general rule remember that:
a dish which is well-cooked on the outside but not
sufficiently cooked inside would have required a lower
temperature and longer cooking time. On the contrary,
a “dry” texture would have required a shorter time and
higher cooking temperature.
For the cooking of meat:
Meat to be cooked in the oven should weigh at least 1
kilo to avoid its becoming too dry. If you want roasts
with a good colour, use very little oil. If the piece is lean,
use oil or butter or a little of both. Butter or oil are on the
other hand unnecessary if the piece has a strip of fat. If
the piece has a strip of fat on one side only, put it in the
oven with this side upwards; when melting the fat will
grease the lower side sufficiently.
Red meat should be removed from the fridge one hour
before cooking otherwise the sudden change of temperature could cause it to become tough. A roast,
especially if of red meat, must not be salted at the
beginning of cooking as salt causes juices and blood to
seep out of the òmeat, thus preventing the formation of
a well-browned crust.
It is advisable to salt the outside of the meat after just
over half the cooking time.
Place the roast in the oven in a dish having a low rim; a
deep dish shields heat.
Meat can be placed on an ovenproof dish or directly on
the grill, under which the dripping pan will be inserted to
collect juice. Ingredients for gravy should only be put in
the dish immediately if cooking time is brief, otherwise
they should be added during the last half hour.
Begin cooking rare meat at a high temperature, reducing
41
the temperature to finish cooking the inside.
The cooking temperature for white meat can be moderate throughout.
The degree of cooking can be checked by pressing the
meat with a fork; if it does not give the meat is cooked.
At the end of cooking it is advisable to wait at least 15
minutes before cutting the meat in order that the juices
are not lost.
Before serving plates can be kept warm in the oven at
minimum temperature.
element according to the thickness of the meat, in order
to avoid burning the surface and cooking the inside
insufficiently.
The formation of smoke caused by drops of juice and
fat can be avoided by pouring l or 2 glasses of water
into the dripping pan.
The grill can also be used to brown, toast bread and grill
certain types of fruit, such as bananas, halved
grapefruit, slices of pineapple, apples, etc. Fruit should
not be placed too near the source of heat.
For the cooking of fish:
Cook small fish from start to finish at a high temperature. Cook medium-sized fish initially at a high temperature and then gradually lower the temperature.
Cook large fish at a moderate temperature from start to
finish.
Check that baked fish is cooked by gently lifting one side
of the gut; the meat must be white and opaque
throughout, except in the case of salmon, trout or
similar.
Cooking times
Cooking times can vary according to the type of food,
its consistency and its volume. It is advisable to watch
when cooking for the first time and check results since
when preparing the same dishes, in the same
conditions, similar results are obtained.
The “TABLE OF COOKING TIMES” relating to cooking
in the oven and by grill is provided as a guide.
Experience will show possible variations to the values
set out in the table.
Grilling
The following types of meat are suitable for grilling.
Mostly meat or offal cut in slices or pieces of various
sizes, but not usually very thick, poultry cut in half and
flattened, fish, some vegetables (e.g. courgettes,
aubergines, tomatoes, etc.), skewers of meat or fish and
seafood.
Meat and fish to be grilled should be lightly brushed with
oil and always placed on the grill; meat should be salted
upon completion of cooking; whereas fish should be
salted on the inside before cooking. The grill should be
positioned in the guides nearest or furthest from the grill
Nevertheless carefully follow the indications given
in the receipe you intend to follow.
42
Attention: do not place any utensils such as dripping
pan, cake tins, casseroles, pyrex dishes, aluminium foil
or other on the base of the oven when the oven is in use.
A stagnation of heat would result which would compromise the results of cooking and could damage the oven
enamel.
TIPS ON COOKING WITH THE ELECTRIC OVEN
Traditional cooking
Heat is conveyed both from the top and bottom of the
oven; thus, it is advisable to put the pot in the central
shelves position. When a higher heat is required either
from the top or bottom, put the pot in an upper or lower
position.
Suggestions for traditional baking
How to bake cakes
Cooking of cakes require a moderate temperature
(usually ranging between 150/200°C) and a 10-minute
pre-heating of the oven. The door should not be opened
during the first 3/4 of the whole baking time.
Beaten up dough should be firm enough to avoid a longer
baking time. When cakes and canapees are arranged
simultaneously on 3 shelves, a runner should be
skipped between the 2 lower shelves.
How to cook meat and fish
Meat should weigh at least 1 kg to avoid excessive
drying. Very soft red meats, to be left rare or only welldone on the outside while keeping their juices, require a
short but high temperature (200-250°C).
White meat, fowl and fish require a low temperature (150170°C).
Ingredients for the gravy should be added to the baking
pan only in the last half hour, unless cooking time is very
short.
The baking point of meat can be checked by pressing a
spoon against the meat. If it feels firm it is properly
cooked, Roastbeef and sirloin require a short cooking
time, as thier insides must keep their redness.
Meat can either be placed an a suitable baking pan or
directly on the grid under which the plate is to be inserted
to collect the juices. When baking time is over it is
advisable to wait at least 15 minutes before slicing the
meat to avoid any spilling of juices.
Dishes can be kept warm in the oven at the lowest temperature, before being served.
Grilling
Heat comes from the top of the oven. It is suitable for
thin meat, toast.
Tips on grill cooking
Almost all kind of meat can be cooked with grill, except
for some game lean meat and meat loaves.
Meat and fish to be grilled should be lightly brushed with
oil and always placed on the grill; meat should be salted
upon completion of cooking; whereas fish should be
salted on the inside before cooking. The grill should be
positioned in the guides nearest or furthest from the grill
element according to the thickness of the meat, in order
to avoid burning the surface and cooking the inside
insufficiently.
The formation of smoke caused by drops of juice and fat
can be avoided by pouring l or 2 glasses of water into
the dripping pan.
FO 0161
Fig. 16
43
COOKING TIME
Temperature
°C
Kinds of food
Beaten mixture cakes in moulds
Black and white flour cake
Royal flat bread-cake
Margherita cake
Pastry
Bottom of cake to be garnished
Butter-milk curd cake
Jam cake
Leavening dough cakes in moulds
Brioche
Small cakes
Pastry
Cream puff
Meringue
Lasagne
Meat (cooking time for every cm of thickness)
Long cooking roast meat
Short cooking roast meat
Meat-loaf
Poultry
Duck 1 1/2 - 2 kg
Goose 3 kg
Roast chicken
Turkey 5 kg
Game
Hare
Roe-deer rib
Deer haunch
Vegetables
Boiled vegetable flan
Fish
Grey mullets
Pizza
Grill
Chops
Sausages
Grilled chicken
Roast veal on the spit 0,6 kg
Chicken on the spit
Inserting slide*
Cooking
time in
minutes
Ordinary
electric oven
Gas oven
175
175
175
2
2
2
2
3
3
60-70
60-70
35-40
200
200
200
2
1
1
3
2
2
15-20
35-40
35-40
200
2
2
35-40
170
200
140
225
2
2
2
2
3
3
3
2
10-15
30-40
120
40-50
175
200
200
2
2
2
2
2
2
12-15
10-12
30-40
200
200
200
175
2
2
2
2
2
2
2
2
120-180
150-210
60-90
about 240
200
200
175
2
2
2
2
2
2
60-90
90-150
90-180
200
2
2
40-45
200
240
2
1
2
2
40-50
20-25
3
3
2
3
3
2
15-20
20-25
60-70
70-80
60-90
* The number of the slide refers to the lowest one (excepted the position on the bottom of the oven, since the dripping pan
can't
be inserted).
GRILL COOKING TIMES
TRADITIONAL GRILL COOKING
Tipes
Quantity kg
N. of the slide from the bottom
Temperature °C
(grill position)
Chicken
Toast
Sausages
Chops
Fish
44
1-1,5
0,5
0,5
0,5
0,5
3
4
4
4
4
Time in
Minutes
Max
Max
Max
Max
Max
30 a side
5 a side
10 a side
8 a side
8 a side
TABLE OF COOKING TIMES
ELECTRIC OVEN
CONVECTION AND MULTI-FUNCTION
N. Guiderom
Type of cooking
Conv.
Trad.
Time
in
Minutes
1-3
1-3
1-3
1-3
1-3
1-3
1-3
2
2
3
2
2
1
3
175
175
175
175
175
175
160
200
200
200
200
200
200
175
60
50
30
70
45
50
30
1
1
1
1
1 ÷ 1,5
2
2
2
2
2
2
2
2
2
2
180
180
220
180
200
200
200
220
200
200
60
70
50
70
70
1
1
1
1
2
2
175
175
200
200
120
110
1
1
1-3
1-3
1-3
2
2
2
180
180
180
180
180
180
30
45
20
Flans
Macaroni pie
Vegetable flan
Sweet or savoury souffles
Pizzas and calzone
2
2
0,75
0,5
1-3
1-3
1-3
1-3
2
2
2
2
185
185
180
200
200
200
200
220
60
50
50
30
Defreezing
Prepared dishes
Meat
Meat
Meat
1
0,5
0,75
1
2
2
2
2
Meat
Veal
Beef
English roastbeef
Pork
Chicken
Casseroles
Beef casserole
Veal casserole
Fish
Filets of cod, hake, sole
Mackeral, turbot, salmon
Oysters
1.
2.
3.
4.
Conv.
1
1
0,5
1,5
1
1
0,5
Temperature °C
Trad.
Cakes
With beaten mixture, in mould
With beaten mixture, in baking tin
Shortpastry, cake tin
Shortpastry with wet filling
Shortpastry with dry filling
With naturally raised mixture
Little cakes
Quantity kg
bottom
200
45
50
70
110
Cooking times are intended after pre-heating ythe oven for approximately 15 minutes.
When cooking on more than one shelf, the guide indicated is the one which is prferable.
Times refer to cooking on only one shelf, for more shelves increase the time by 5-10 minutes.
For roasted beef, veal, pork or turkey with bone or rolled increase times by 20 minutes.
45
MAINTENANCE
Before each operation, disconnect the unit.
Cleaning the cooker
Drops of sauce, fruit juice etc., should be removed as
soon as possible with a soft cloth soaked in warm
detergent water. Do not use steel wool or knives to take
off layers of crust. Remove stubborn marks with a well
wetted soap impregnated pad, but care must be taken
not to scratch the enamel. Wash the enamelled grids
with water and detergent; these can also be washed a
dishwasher.
Take off the burner covers and the grids and wash them
carefully with warm water and detergent. Dry them well
before putting them back in position.
Moreover, make sure that these are properly re-placed.
The burner can be rubbed with steel wool or a slightly
abrasive cloth.
Clean the oven door and crystal cover, in models
equipped with these items, only with warm water, and
avoid the use of rough cloths or abrasive substances; in
cookers with an automatic ignition the sparkling bulb
should be cleaned periodically and accurately to avoid
difficulties in lighting; furthermore check that the burner
holes are not obstructed.
Cleaning the oven
Clean carefully the oven cavity after use when it is still
warm. In fact, at this moment it is easy to take off
deposits of fat or other substances such as fruit juice,
sugar particles or fat. You can use warm detergent water
or one of the appropriate spray oven cleaners. Do not
direct the spray at the mat steel parts as this could
damage them and always follow the manufacturer's
instructions. Clean the oven acces-sories (grate, gridplate etc.) with warm water and detergent.
Remove possible incrustations with a slightly abrasive
powder.
Never line any part of the oven with aluminium foil.
It would result in an accumulation of heat which
might damage the cooking results and also
damage the enamel.
inside the holder, instead of the cylinder, (on request) a
set of grills and containers, converting the cylinder holder
into a comfortable closet.
Oven lamp replacement (Fig. 17)
Disconnect the appliance. Unscrew the lamp and
substitute it with another fitting for a higher temperature (300°C) with the folowing characteristics:
Tension:
230 V (50Hz)
Power:
15W
Convection:
E14
FO 0424
Fig. 17
Cleaning the oven door
For a more complete cleaning of the oven door, it is
advisable to disassemble it in the following way (Fig. 18):
open the door fully, turn the two caps situated on the
arm of the hinge to 180° partially close the door to an
angle of 30°, lift the door and extract from the front.
Re-mount the door by reversing the operation described
above.
Controls - Sundries
Periodically check the condition of the flexible pipe of
gas connection and make it replaced by skilled
technicians as soon as it shows abnormalities. Annual
replacement is recommended.
Have the cocks periodically lubricated by skilled
technicians. In case of unusual working have the range
checked by skilled technicians.
In ranges with cylinder holder, do not use this space to
leave a non-connected or an empty cylinder.
Cylinder holder
The units equipped with cylinder holder must be installed
in such a way to ensure a sufficient ventilation inside the
holder itself; otherwise there is the chance to install
46
FO 0967
Fig. 18
INSTRUCTIONS FOR THE INSTALLER
The following instructions are meant for a qualified installer, in order that the operations of installation, regulation, and
service are executed according to the existing regulations.
Whenever changes are mode involving the disconnection of the machine it is necessary to proceed with maximum
caution.
THE MANUFACTURING COMPANY DECLINES ANY RESPONSABILITY FOR POSSIBLE DAMAGES
RESULTING FROM AN INSTALLATION WHICH DOESN'T COMPLY WITH THE RULES IN FORCE
INSTALLATION ENVIRONMENT
Warning - This unit can be installed and can work only in constantly ventilated rooms, according to the national rules
in force.
In order to make the gas unit work properly, it is necessary that air sufficient to gas combustion can naturally flow in
the room. (The installer must follow the rules in force).
The air flow into the room must come directly through openings of external walls - See fig. 19 - 20.
These openings must have a free passage of at least 100 cm2 (one or more openings can be made).
AIR INLET ARIA
ENTRATA
SECTION MIN.
SEZIONE
MIN.cm
100
2 cm2
200
AIR INLET
ENTRATA ARIA
SECTION
SEZIONE
MIN.
100 cm2 MIN.
200 cm2
Fig. 19
FO 0159
Fig. 20
FO 0160
These openings (or opening) should be realized in such a way not to be occluded both from inside and outside and
preferably positioned near the floor, opposite the combustion products discharge. In case these systems can't be
realized in the room where the unit is installed, the necessary air can come from a room nearby, provided that this
room is not a bedroom or a dangerous environment and it is ventilated as requested, from national rule in force.
COMBUSTION PRODUCTS DISCHARGE
Gas cooking units must discharge combustion products through hoods directly connected to flues or outside (Fig.
21).
In case the hood can't be installed it is recommended the use of an electric fan applied to the external wall or to the
window of the room, provided that in that room the openings to let air flow in are realized (national rule in force) (Fig.
22).
This electric fan must be powerful enough to ensure in a kitchen an air replacement of 3 to 5 times its volume per hour.
ELECTRIC FAN
ELETTROVENTILATORE
CAPPA
HOOD
ENTRATA ARIA
AIR INLETMIN.
SEZIONE
SECTION
200
cm2
MIN.LA
100
cm2
PIU'
SEZIONE
AGGIUNTIVA
PLUS AN
CORRISPONDENTE
ADDED
ALLA
PORTATA
SECTION
DELL'ELETTROCORRESPONDING
VENTILATORE
TO ELECTRIC
FAN POWER
AIR INLET
SECTION ARIA
ENTRATA
2
MIN. 100 cmMIN.
SEZIONE
200 cm2
FO 0161
Fig. 21
FO 0439
Fig. 22
47
POSITIONING
This appliance belongs to the class "X".
It has been designed to be placed close to furniture units
not exceeding the height of the working level (EN 60 3352-6).
LEVELLING
The appliance is provided with adjustable small feet
placed in the back and front corners od the base.
By adjusting the small feet (fig. 23-A) it is possible to
change the height of the appliance so as to ensure a
better levelling with other surfaces and a uniform
distribution of the liquids contained in pans or pots.
BALANCING THE LID
Fig. 23-A
FO 0063
Fig. 23-B
FO 0064
The models provided with crystal lids are equipped with
specially balanced springs, inserted in the hinges at the
back of the appliance, to allow the lid to be closed
smoothly and easily.
You can use a screwdriver to adjust the closure of the
lid. The necessary force for opening/closing the lid can
be increased by turning the adjusting screw 2 or 3 times
as shown in Fig. 23-B.
GAS CONNECTION
Gas connection must be carried out according to the
rules in force.
The manufacturing company release the unit, once
tested, adjusted for the kind of gas stated on the rating
plate located on the back of the range, next to
connection pipe. Be sure that you are going to connect
the unit to the same kind of gas written on the plate.
Otherwise, follow all the instructions of the paragraph
"REGULATION TO DIFFERENT KINDS OF GAS".
For best efficiency and lowest consumption, be sure that
manifold gas pressure respects the values in the table
of "Burners characteristics".
If gas pressure is different (or variable) from the proper
one, a suitable pressure regulator should be installed on
feeding pipe.
The use of pressure regulators for liquid gas (LPG) is
allowed provided they are modelled in conformity with the
rules in force
RUBBER PIPE HOLDERS SUPPLIED WITH
THE APPLIANCE
If connecting the appliance to a natural gas supply
(or to a town gas supply, where allowed according
to the appliance category) : fit the rubber pipe holder
type “A”, as shown in Fig. 24.
If connecting the appliance to LPG supply : fit the
rubber pipe holder type “B”.
Always insert the gasket “C” between the feeding pipe
and the rubber pipe holder.
The appliance is preset to be connected using a rigid
pipe or a flexible metal pipe. To ensure higher safety, it is
recommended to carry out the connection using rigid
pipes or flexible stainless steel pipes (according to the
national rules in force).
48
Fig. 24
FO 0067
CONNECTION USING A RIGID PIPE OR A
FLEXIBLE METAL PIPE
To ensure higher safety, it is recommended to carry out
the connection to the gas system using rigid pipes (ex.
copper) or using flexible stainless steel pipes (according
to the national rule in force), not to cause any stress to
the unit.
Gas feeding pipe fitting is Gc 1/2.
IMPORTANT
Once installation is complete, check the perfect seal of
every pipe fitting, using a soapy solution, never a flame.
YES
For this type of installation, connection to the gas supply
should be carried out using only and exclusively flexible
metallic tubes in conformity with the national rule in
force.
FLEXIBLE
RUBBER
GAS PIPELINE
ELECTRIC WIRE
CONNECTION USING FLEXIBLE,
NON METAL PIPES
When the connection can be easily inspected in its full
extent, there is the chance to use a flexible pipe
according to the netional rules in force.
The flexible pipe must be tightly fixed using clamps
according to the national rule in force.
The flexible pipe should be made ready for use in such
a way that:
- nowhere it can reach overtemperature, other than
room temperature, higher than 30°C; if the flexible
pipe, to reach the cock, must run behind the range,
it must be installed as shown in Fig. 25;
- it is no longer than 1500 mm;
- it shows no throttles;
- it is not subject to traction or torsion;
- it doesn't get in touch with cutting edges or corners;
- it can be easily inspected in order to check its
condition.
NO
FLEXIBLE
RUBBER
GAS PIPELINE
ELECTRIC WIRE
Fig. 25
FO 0163
The control of preservation of the flexible pipe consists
in checking that:
- it doesn't show cracks, cuts, marks of burnings both
on the end parts and on its full extent;
- the material is not hardened, but shows its normal
elasticity;
- the fastening clamps are not rusted;
- expiry term is not due (5 years).
If one or more abnormalities are seen, do not repair the
pipe, but replace it.
To connect the range to LPG cylinder, use a flexible pipe
(according to the national rule in force) introducing it into
the cylinder holder through the lower opening in the back
and set it in position fastening it with the two laces, as
shown in Fig. 26.
Attention: it should never touch the left side of the holder.
Use the proper holder bottom (A - Fig. 26) to avoid the
cylinder touch the floor.
FO 0698
Fig. 26
49
REGULATION TO DIFFERENT
KINDS OF GAS
CAPS
To adapt the range to a kind of gas different from that
one it is preset to, follow the instructions below in their
order.
Replacement of rubber pipe holder (Fig. 27)
LPG preset range:
to set the range ready for natural gas or town gas, use
rubber pipe holder «A».
Natural gas preset range:
to set the range ready for town gas, use the same rubber
pipe holder used for natural gas; to set it ready for LPG,
use the rubber pipe holder «B» (in the equipment).
Always insert the gasket «C» between the feeding pipe
and the rubber pipe holder. (Fig. 27)
FO 0067
Fig. 27
FO 0465
Fig. 29
REPLACEMENT OF THE FISH-KETTLE
BURNER NOZZLE:
(For models supplied)
- remove the plate or glass cover by lifting it from the
relevant brackets;
- remove the grills;
- unthread the caps, baffles and burner covers;
- dismount the two cover brackets by unscrewing the
relevant fixing screws (fig. 30);
- lift the surface slightly from the bottom part and remove
pushing it towards the front of the cooker;
- using a no. 7 spanner unscrew and remove (fig. 31) the
nozzle replacing it with the new one (see tab. 2 nozzles).
When operating with city gas the fish-kettle burner does
not require caps.
Remount the parts following the operations described in
reverse.
REPLACEMENT OF NOZZLES AND
ADJUSTMENT
The unit is not equipped with town gas nozzles. If
necessary, ask the nearest retailer or the nearest
Zanussi Technical Service centre for the special set
of nozzles and replace the others as explained in
the following paragraph.
Nozzle replacement:
Remove the grills;
extract the caps and the wall baffles of the burners;
using a socket spanner 7 unscrew and remove (fig. 28)
the nozzles replacing them with those ones required for
the kind of gas in use (see table 2).
To adapt the nozzles to town gas, after installing them,
screw the provided grid filter on them; for the semi-quick
and auxiliary burner grid filter A, hole Ø10, for quick
burner grid filter C, hole Ø16 (fig. 29).
Reassemble the parts following the same procedure
backwards.
FO 0392
50
Fig. 28
FO 0069
Fig. 30
FO 0070
Fig. 31
Adjustment of minimum level of plate burners:
To adjust the minimum level, turn the knob to the
position of minimum flame, remove the knob (Fig. 32)
and: in case of conversion from natural gas to LPG,
tightly screw the by-pass pin of the cocks;
in case of conversion from natural gas to town gas,
instead, unscrew by-pass pin three-fourth turn; when
converting from LPG to natural gas unscrew about onefourth turn by-pass pin, and onr turn when converting to
town gas until a regular small flame is reached.
Reassemble the parts following the same procedure
backards.
Check that, turning quickly the knob from the maximum
position to the minimum one, the burner doesn't go out.
FO 0068
Fig. 32
Replacement of oven burner nozzle:
To replace the oven nozzle, follow this procedure:
remove the bottom of the oven, unscrew screw 1 (fig. 33)
and take the oven burner out.
With a socket spanner 7 unscrew and remove the
nozzle, situated in the bottom of the oven, replacing it
with the proper one (see Table 2); reassemble the burner
following the same procedure backwards.
Minimum level adjustment of oven burner
In ranges with thermostat, after setting the oven on
maximum temperature with closed door for about 10
minutes, turn the knob of the thermostat on 140, remove
the knob and:
- in case of conversion from natural gas to LPG, tightly
screw the by-pass pin of thermostat (fig. 32);
- in case of conversion from natural gas to town gas,
unscrew the by-pass pin about one turn;
- converting from LPG to natural gas, then, unscrew
the by-pass pin about half turn and about one turn
and a half when converting to town gas, until a regular
small flame is reached.
FO 1072
Fig. 33
ADJUSTMENT INSTRUCTIONS FOR THE
BY-PASS PIN OF THE OVEN BURNER
THERMOSTAT
In the models equipped with rond head by-pass pin, operate as follows to adjust such a device:
-
take out the knobs;
remove the frontal;
adjust xith a thin screwdriver, see figure 34;
finally check that turning quickly the tap from
maximum position to minimum position, the burner
doesn't switch off.
FO 1061
Fig. 34
51
SPECIFICATIONS OF THE BURNER AND OF THE INJECTORS
TYPE
OF GAS
NATURAL
GAS
(Methane)
BURNER
1/100 mm
NORMAL
POWER
kW
REDUCED
POWER
kW
Rapid
Semi-rapid
Auxiliary
119
96
70
3,0
2,0
1,0
Fish kettle burner
Oven with thermostat
Oven with tap
116
119
105
Rapid
Semi-rapid
LIQUID
Auxiliary
GAS
(But./Prop.)
Fish kettle burner
Oven with thermostat
Oven with tap
TOWN
GAS
Rapid
Semi-rapid
Auxiliary
Fish kettle burner
Oven
INJECTORS
Table 2
NORMAL
POWER
m 3/h
g/h
0,65
0,45
0,33
0,286
0,190
0,095
-
3,0
3,0
2,4
1,0
0,85
1,1
0,286
0,286
0,228
-
86
71
50
88
82
73
2,8
2,0
1,0
3,2
3,0
2,4
0,65
0,45
0,33
0,85
1,0
1,1
-
202
144
72
230
216
173
282
210
142
240
254
3,0
2,0
1,0
3,0
3,0
0,65
0,45
0,33
0,85
1,0
0,680
0,453
0,227
0,680
0,680
-
FEEDING
PRESSURE
m bar
20
28-30/37
8
Plate and oven burners don't need regulation of primary air.
WARNING
If the pressure of gas used is different (or variable) from that foreseen , an appropriate pressure regulator must be
installed on the entry tube.
in case of pressure regulators for GPL are used, these must conform to regulation in force.
52
INSERTION POSSIBILITY
In case of insertion of the appliance between kitchen
units the dimensions to be respected are shown in fig.
35.
500
When the kitchen is installed according to class 2, subclass 1 (i.e. built-in) for the gas connection use only
flexible metallic tubes conforming to the national rule in
force.
650
100
Fig. 35
FO 1076
ELECTRICAL CONNECTION
The unit is preset to work with a voltage of single phase
230 V.
Before making the connection make sure that: the
energy power available in the user's house is sufficient
for the normal supply of this appliance (see rating plate).
The unit is correctly connected to earth through a
suitable plug and according to the installation country
Laws.
The socket or the omnipolar switch used for the
connection must be easilv reached with the installed
appliance. The appliance is supplied without electric
cord: consequenrly, you have to install a plug fit for the
load shown in the serial number plate. The plug has to
be connected to an adequate socket.
If you wish to directly connect to the mains, you have to
interpose an omnipolar switch with a minimum opening
between contacts of 3 mm, between the unit and the
mains, complying with the existing regulations. The
brown live wire (originating from the clamp of the cooker
junction box) must always be connected to the phase
of the mains supply. In any case, the supply cord must
be positioned in such a way as it doesn't reach in any
point a temperature higher by 50°C than the room temperature.
Should the supply cord need to be replaced, it is
necessary that the yellow/green earth wire is about 2cm
longer than the live and neutral ones (Fig. 36).
After the connection, test the heating elements for about
3 minutes to ensure that they are working correctly.
The manufacturer refuses any responsability in
cases where normal safety measures are not
observed.
Neutral wire
Phase
Ground (yellow - green)
FO 0073
Fig. 36
53
WHAT TO DO IF THE APPLIANCE DOESN'T WORK
If the appliance doesn't work properly check the following
points before asking for service:
The flow of gas seems abnormal
Make sure that:
— the flame speader holes are not obstructed;
— the pressure regulator is working;
— the bottle valve is completely open.
Gas smelle in the room
Make sure that:
— the gas valve is not open;
— the gas supply tube is well positioned and in good
condition; remember to replace it at least once a
year.
Never look for an escape of gas with a match;
instead use soap and water.
Cooking time is too long
Check that the temperature is correct for the type of food
to be cooked.
The cooker smokes
We advise you to clean the oven after use. Splashes of
fat can occur during the cooking of meat and, if the oven
isn't cleaned properly, these produce smoke and bad
smell. (see paragraph concerning cleaning).
The oven lamp doesn't work
The lamp has burnt out. To replace it follow the
instructions given in the relative paragraph.
If, after following all the above checks the appliance still
doesn't work, call your nearest Service Centre givin them
all the necessary information, such as model and serial
number of the appliance.
The oven doesn't heat
Make sure that the oven knobs are in the correct
worrking positions.
MAINTENANCE - TECHNICAL ASSISTANCE
The gas cocks must be periodically lubricated to ensure
good working and safety.
Maintenance should be performed as follows:
Remove the knob and panel after having taken out
fastening screws.
Loosen the two screws located at the sides of the cock
bar.
Remove the cone and clean it carefully.
Then, apply a thin layer of grease non soluble in water,
suitable for gas cocks. Take care not to obstruct the gas
flow holes by an excess of grease. Reassemble the
whole with utmost care performing the operations
described above inversely.
If the equipment uses two gas, the burners are provided
with small cages (Fig. 26) which must be carefully
cleaned at regular intervals, making sure that the small
holes are not obstructed.
ORIGINAL SPARE PARTS
This machine, before leaving the factory, has been
tested and studied by many experts and specialists, in
order to give you the best results.
Any repair work which needs to be carried out should
be done with the utmost care and attention.
For this reason we reccomend that for any problem you
contact the dealer who sold it to you, or our nearest
authorized Service Centre, specifying the nature of the
problem and the particular model which you own.
Original spare parts, certified by the manufacturer of the
product and marked with the following sign,
can only be found at our approved Technical Assistance
Centres and in authorised Spare Parts Shops.
54
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising