Electrolux EKM6717X User manual

Electrolux EKM6717X User manual
Mixed-Fuel Cooker
INSTRUCTION BOOKLET
Mod. EKM 6717 X
35692-0501
PH-VN-TH
Important safety information
This warnings has been given for the safety of you and others. We therefore ask you to carefully read the procedures of
installing and using this cooker.
Installation
•
•
•
•
•
•
•
•
•
The work of installation must be carried out by
competent and qualified installers according to the
regulations in force.
Any modifications to the domestic electrical mains
which may be necessary for the installation of the
appliance should be carried out only by competent
personnel.
Ensure a good ventilation around the appliance. A poor
air supply could cause lack of oxygen.
This appliance is not connected to a combustion
products evacuation device. It must be installed and
connected in accordance with current installation
regulations. Particular attention shall be given to the
relevant requirements regarding ventilation.
The use of a gas cooking appliance results in the
production of heat and moisture in the room in which
it is installed. Ensure that the kitchen is well ventilated: keep natural ventilation holes open or install a
mechanical ventilation device (mechanical extractor
hood).
Prolonged intensive use of the appliance may call for
additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.
Avoid installation of the cooker near inflammable
material (e.g. curtains, tea towels, etc.).
Supply the appliance with the type of gas stamped
on the relevant adhesive label situated in the immediate vicinity of the gas connection tube.
The appliance has to be placed on the floor and it
cannot be placed on a base.
Child Safety
•
•
This appliance has been designed for use by adults.
Take care, therefore, that children do not attempt to
play with it.
The appliance remains hot for a long time after being
switched off. Supervise children at all times, paying
attention that they do not touch surfaces or remain
in the vicinity of the appliance when in use or when
not completely cooled.
During Operation
•
•
•
•
•
2
This product is intended for the cooking of food and
must not be used for other purposes.
It is dangerous to modify, or attempt to modify, the
characteristics of this appliance.
The appliance becomes very hot with use, and retain
their heat for a long period after use. Care should be
taken to avoid touching heating elements inside the
oven.
Always stand back from the oven when opening
the oven door during cooking or at the end of it
to allow any build up of steam or heat to release.
Unstable or deformed pans should not be placed on
the burners or plates in order to avoid accidents
caused by upsetting or boiling over.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Particular care should be taken when cooking with
oil or fat.
If the appliance is fitted with a cover, its function is to
protect the surface from dust when closed and to accumulate splashes of grease when open. Do not use
for other purposes.
Always clean the cover, if present, before closing.
Leave the burners and/or plates to cool before closing
the cover (if present).
All the covers (if present), in plate glass or enamel,
are removable to facilitate cleaning.
Always ensure that the knobs are in the « »
(Stop) position when the appliance is not in use.
Always insert the dripping pan when using the grill or
when cooking meat on the grid. Pour a little water
into the dripping pan to avoid grease burning and
creating unpleasant smells.
Always use oven gloves to remove dishes from the
oven.
The oven accessories should be washed before using
for the first time.
Take care when using cleaning products in spray
form: never direct the spray onto the resistance or the
thermostat bulb.
If, when placing food in the oven, or when removing it,
a large quantity of oil, juice, etc. spills onto the
bottom of the oven, re-clean before starting to cook
to avoid unpleasant smoke and also the possibility
of these substances catching fire.
For reasons of hygiene and safety this appliance
must always be kept clean. A build up of grease or
other food can cause fires.
This appliance cannot be cleaned with steam or with
a steam cleaning machine.
The holes on the bottom of the oven must never be
obstructed. Do not cover the sides of the oven with
aluminium foil, in particular the lower part of the
opening.
The appliance is heavy, move it carefully.
Before maintenance and cleaning disconnect the
appliance and allow to cool.
To facilitate ignition, light the burners before
placing pans on the grid. After having lit the
burners check that the flame is regular.
Always lower the flame or turn it off before removing
the pan.
Ensure that the oven grids are inserted correctly.
If there are self-cleaning panels they should only be
cleaned with soap and water (see cleaning
instructions).
Only heat-resistant plates may be placed in the
drawer situated under the oven.Do not put
combustible materials there.
Service
•
In case of repairs, do not attempt to correct yourself.
Repairs carried out by unqualified persons can cause damage. Contact an authorized Technical
Assistance Centre and insist an original spareparts.
Contents
For the user
For the installer
Important safety information
2
Instructions for the installer
23
Control panel
4
Installation
24
Using the hob
5
Gas connection
25
Electric hotplate control
6
Electrical connection
26
Hints and Tips
7
Electric oven
8
Before the first use of the appliance
10
Using the oven
11
Suggestions for using the hob
12
Suggestions for using the oven
13
Cooking tables
16
Cleaning and maintenance
18
Cleaning the oven
19
Something not working
22
Service and spare parts
22
Environmental Information
•
•
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
on the product or on its packaging
The symbol
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
It is very important that this instruction book
should be kept safely for future consultation. If
the appliance should be sold or given to
another person, please ensure that the booklet
goes together with it, so that the new owner
can know of the functions of the machine and
also be aware of the warnings.
Guide to Use the instructions
The following symbols will be found in the text to
guide you throughout the Instructions:
Safety Instructions
!
Step by step instructions for an operation
Hints and Tips
Environmental information
This appliance complies with the following
E.E.C. Directives:
• 73/23 - 90/683 (Low Voltage Directive);
• 89/336 (Electromagnetical Compatibility
Directive);
• 90/396 (Gas Appliance Directive);
• 93/68 (General Directives);
and subsequent modifications.
MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna 298
47100 FORLÌ (Italy)
These instructions are only for the countries
stated by the symbol printed on the front cover
of this instruction book.
3
Control panel
1
1.
3.
3.
4.
5.
2
3
Back left burner control knob (semi-rapid)
Front left burner control knob (rapid-triple crown)
Front right burner control knob (auxiliary)
Back right cast iron hotplate control knob
Oven function control knob
5
6.
7.
7.
9.
6
7
89
Oven thermostat control knob
Minute minder
Mains on Light
Oven thermostat pilot light
Accessories
The Oven Cavity
Grill element
4
Oven Light
Baking Tray
Oven Shelf
Oven fan Turnspit hole
4
Dripping Pan
Using the hob
Control knobs on the gas hob
The knobs for using the gas hob of the cooker are found
on the control panel. The regulation knobs could be
turned in anti-clockwise direction until the small flame
symbol, and vice-versa for the larger symbol.
No gas supply
Maximum gas supply
Minimum gas supply
!
To light a burner:
1. push the relevant control knob in completely
and turn it anticlockwise to the maximum
position;
3. then, check the flame is regular and adjust it
as required.
If the burner does not ignite, turn the control knob to zero,
and try again.
If after a few attempts the burner does not ignite, check
that the burner cap and crown (see figure - A,B) are
correctly positioned.
To interrupt the supply of gas, turn the knob in a
clockwise direction to the position """.
When switching on the mains, after installation or
a power cut, it is quite normal for the spark
generator to be activated automatically.
If you use a saucepan which is smaller than
the recommended size, the flame will spread
beyond the bottom of the pan, causing the
handle to overheat.
Triple-crown burner
A
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
B
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
If the control knobs become difficult to turn, please
contact your local Service Force Centre.
Triple-crown burner
Always ignite the burner before putting the pans
on.
C
A - Burner cap
B - Burner crown
C - Spark generator
If after a few attempts the burner does not ignite, check
that the burner cap and crown are correctly positioned.
5
Using the wok stand
A wok stand is provided to enable you to use a round
bottomed wok on the hob.The wok stand must only be
used on the triple crown burner and should not be used
with any other type of wok or pan.
When fitting the wok stand, ensure the recesses in the
frame fit securely onto the bars of the pan supports, as
shown in the picture.
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
minimum
diameter
Large (ultra-rapid
triple crown)
Medium (semi-rapid)
Small (auxiliary)
180 mm.
120 mm.
80 mm.
maximum
diameter
260 mm.
220 mm.
160 mm.
Electric hotplate control
To switch on the hotplate, turn the relevant control knob
to the required heat setting.
The control knob is numbered 1 - 6
0 - OFF
1 - Minimum
6 - Maximum.
We recommend the plate is switched to maximum (6) for
a short while to boost the plate, and then adjusted to the
required setting.
Suggestions for the correct setting of the plates are given
in the following table.
Very Gentle
1
Gentle
2
Slow
3
Medium
4
High
5
Fast
6
To keep food warm
To melt butter and chocolate
To prepare cream-sauces, stews
and milk puddings or to fry eggs
Dried vegetables, frozen food, fruit,
boiling water or milk
Boiled potatoes, fresh vegetables,
pâtés, soups, broths, pancakes or
fish
Larger stews, meat roll, fish,
omelettes, steaks
Steaks, escalopes and frying.
It is important to note that the plate may smoke
and produce a slightly unpleasant odour when used
for the first time. This is quite normal and will
disappear after a short while.
6
Hints and Tips
Saucepans for use on solid plates should have several
characteristics:
• They should be fairly heavy duty
• They should fit the heat area exactly, or be slightly
larger for efficient use, NEVER smaller.
• They should have a flat base to ensure good
contact with the plate.
This is particularly important when using pans for high
temperature frying or pressure cooking.
You can switch off the plate a short while before
you finish cooking, and the final stage will be
completed on the accumulated heat. Similarly,
stews etc. cooked in well covered saucepans cook
at lower temperature which is more economical.
Ensure pans are large enough to avoid liquids
being spilt onto the plates.
Never leave the plates on without a pan on them
or with an empty pan on them.
Take care never to lean or reach over a hot electric
plate. Always point pan handles inward or over the
work surface next to the hob to avoid accidentally
knocking over a pan as you pass by.
In models supplied with a cover, if it is made
of glass, it should not be closed when the
burners are still hot, as it could splinter.
Recommended pottery
Remember that a wide-bottomed pan allows a faster
cooking than a narrow one. Always use pots which
properly fit what you have to cook.
Particularly make sure that the pans are not too small
for liquids, since these could easily overflow.
Moreover, the pans should not be too large for a faster
cooking. In fact, grease and juices may spread on the
bottom and burn easily.
It is better to use non-openable moulds for baking cakes.
In fact, an openable mould lets juices and sugar leak
through, falling on the bottom of the oven and
consequently burning on the bottom of the baking tray,
making cleaning difficult.
Avoid putting plastic-handled pans in the oven as they
are not heat-proof. You should use pans with the right
diameter to fit the burner, in order to make the most out
of it, thus reducing gas consumption.
It is also advisable to cover any boiling casserole and,
as soon as the liquid starts boiling, lower the flame
enough to keep the boiling point.
The effects of dishes on cooking
results
Dishes and tins vary in their thickness, conductivity,
colour, etc. which affects the way they transmit heat to
the food inside them.
A Aluminium, earthenware, oven glassware and bright
shiny utensils reduce cooking and base browning.
B Enamelled cast iron, anodized aluminium, aluminium
with non-stick interior and coloured exterior and dark,
heavy utensils increase cooking and base browning.
7
Electric oven
Oven function and thermostat
control knobs
They enable to select the most appropriate type of
heating for the different cooking requirements by
appropriately connecting the heating elements and
adjusting temperature to the required level.
Turn the thermostat control knob clockwise to select
temperatures between 50°C and 230°C (MAX).
0
The oven is off.
Conventional cooking - The heat comes
from both the top and bottom element,
ensuring even heating inside the oven.
Fan cooking - This allows you to roast or roast
and bake simoultaneously using any shelf,
without flavour transference.
Inner grill - It can be used for grilling small
quantities.
Grill turnspit - The turnspit can be used for
either spit roasting meat or for kebabs and
smaller pieces of meat.
Full grill - The full grill element will be on.
Pizza - The bottom element provides direct
heat to the base of pizzas, quiches or pies,
while the fan ensures air is circulated to cook
the pizza toppings or pie fillings.
Bottom heating element - The heat comes
from the bottom of the oven only.
Mains on Light
The mains on light will come on when the oven function
control knob and/or the cooking zone control knob is set.
Oven thermostat pilot light
The thermostat control light will come on when the
thermostat control knob is turned. The light will remain on
until the correct temperature is reached. It will then cycle
on and off to show the temperature is being maintained.
8
The minute minder
The minute minder will mark the end of a timed period
with an acoustic alarm. The maximum timing is 120
minutes.
To set the minute minder:
1. Select the desired cooking function with the oven
function control knob.
2. Turn the minute minder control knob clockwise
until the 120-minute position and then back to
the required time.
3. Once the pre-set time has elapsed, an acoustic
signal will be heard and the oven will automatically
switch off.
Turn the minute minder control knob to the
position and the oven function and thermostat
control knobs to OFF position.
Turn the minute minder control knob to the
position if you want to cook without setting a
timed period.
The safety thermostat
In order to avoid excessive overheating due to incorrect
use of the appliance or else to a faulty component, the
oven is equipped with a safety thermostat which cuts off
the power supply if necessary. Operation is restored
automatically when the oven temperature decreases to
normal values. Therefore, if the thermostat cuts in because
you have not been using the appliance correctly, the oven
can be used again simply by waiting for the appliance to
cool down. If, instead, the thermostat cuts in because of
a faulty component, you should call the Service
Department.
Storage drawer
The storage drawer is located underneath the oven cavity.
During cooking the storage drawer may become
hot if the oven is on high for a long period of time,
therefore flammable materials such as oven gloves,
tea towels, plastic aprons etc. should not be
stored in the drawer.
Oven accessories such as baking sheets, will also
become hot, therefore care should be taken when
removing these items from the drawer whilst the
oven is in use or still hot.
9
Before the first use of the appliance
Before using the appliance, remove all
packaging, both inside and outside the
appliance, including the advertising labels
and any protective film.
Before cooking for the first time, carefully wash
the oven accessories.
Before using the oven, make sure the minute
minder control knob is in the
position.
Before first use, the oven should be heated without
food. During this time, an unpleasant odour may be
emitted. This is quite normal.
1. Switch the oven function control knob to
.
traditional cooking function
2. Set the thermostat control knob to MAX.
3. Open a window for ventilation.
4. Allow the oven to run empty for approximately
45 minutes.
This procedure should be repeated with the full grill
cooking function
and the fan cooking function
for approximately 5-10 minutes.
Once this operation is carried out, let the oven
cool down, then clean the oven cavity with a
soft cloth soaked in warm water to which a little
mild washing-up liquid has been added.
10
Using the oven
Always cook with the oven door closed.
Stand clear when opening the drop down
oven door. Do not allow it to fall open support the door using the door handle, until
it is fully open.
The oven has four shelf levels.
The shelf positions are counted from the bottom
of the oven as shown in the diagram.
It is important that the shelf is correctly positioned.
4
3
2
1
Attention! - Do not place cookware and objects
directly on the oven base and do not cover any
part of the oven with aluminium foil while cooking,
as this could cause a heat build-up which would
affect the baking results and damage the oven
enamel. Always place pans, heat-resisting pans
and aluminium trays on the shelf which has been
inserted in the shelf runners.
When cooking with the oven or grill, the cover must
be kept open to avoid overheating.
Condensation and steam
The oven is supplied with an exclusive system which
produces a natural circulation of air and the constant
recycling of steam. This system makes it possible to
cook in a steamy environment and keep the dishes soft
inside and crusty outside. Moreover, the cooking time
and energy consumption are reduced to a minimum.
During cooking steam may be produced which can be
released when opening the oven door. This is absolutely
normal.
However, always stand back from the oven
when opening the oven door during cooking
or at the end of it to allow any build up of
steam or heat to release.
When food is heated, it produces steam in the
same way as a boiling kettle does. When
steam comes in contact of the oven door glass,
it will condense and produce water droplets.
To reduce condensation, ensure the oven is
well heated before placing food in the oven
cavity. A short oven pre-heating (about 10
minutes) will then be necessary before any
cooking. We recommend you to wipe away
condensation after each use of the appliance.
To open the oven door, always catch the
handle in its central part.
11
Suggestions for using the hob
Start your cooking with a big flame by turning the knob
to the symbol . Then adjust the flame as necessary.
The outside of the flame is much hotter than its inside
(nucleus). Accordingly , the top of the flame should lick
the bottom of the pan. Excessive flames mean a waste
of gas.
In contrast with electric grids, gas burners do not require
flat-bottomed pans: the flames lick the bottom and
spread the heat all over the surface.
No special pans are required for gas burners. However,
thinwalled pans transmit the heat to the food more
quickly than thick-walled ones.
Since heat doesn't spread evenly on the pan's bottom,
the food may only be partially heated. Consequently it
is advisable to stir the food many times.
A thick pan bottom prevents partial overheating as it
allows sufficient thermic compensation.
Avoid very small pans. Wide and shallow pans are more
suitable than narrow and deep ones as they allow a
faster heating. Cooking is not quickened by placing
narrow pans on wide burners. The result is just a waste
of gas. For a proper usage, place small pans on small
burners and large pans on large burners.
Remember to cover pans to reduce gas consumption.
12
Suggestions for using the oven
Traditional cooking
As heat originates from top and bottom, dishes should
preferably be placed in the middle. If cooking requires
more heat from the bottom or the top, use the upper or
lower level.
Fan cooking
Heat is transmitted to dishes by hot air forcibly circulated
inside the oven by a fan placed at the back of the oven.
By this method, heat is quickly and evenly circulated
throughout the oven, permitting several different dishes
to be cooked at the same time on different levels.
With this cooking method, through the elimination of
humidity in the air and a drier environment, smells and
tastes are not given off and do not mix with those of
other dishes.
Thanks to this possibility of cooking on several levels,
you can cook up to three different dishes at the same
time, to be consumed immediately or frozen. You can
also cook on only one level. In this case, it is advisable
to place the dish on the lower level for better cooking
control.
This oven is particularly suitable for defreezing rapidly,
sterilizing preserves, homemade jams and, finally, for
drying mushrooms and fruit.
Cooking in the multi-function
oven
This type of oven permits difrferent types of cooking:
traditional, fanned heat and grilling; cooking can therefore
be optimized.
Using the oven
For the cooking of cakes
Pre-heat the oven, unless indicated differently, for at
least 10 minutes before use. Do not open the oven door
when cooking dishes which must raise (e.g. raised
pastries and soufflés); the jet of cold air would block the
raising process. To check if cakes are cooked, insert a
toothpick into the mixture; if it comes out clean the cake
is ready. Wait until at least 3/4 of the cooking time has
passed before doing this check.
As a general rule remember that:
a dish which is well-cooked on the outside but not
sufficiently cooked inside would have required a lower
temperature and longer cooking time. On the contrary,
a “dry” texture would have required a shorter time and
higher cooking temperature.
13
For the cooking of meat
Meat to be cooked in the oven should weigh at least 1
kilo to avoid its becoming too dry. If you want roasts with
a good colour, use very little oil. If the piece is lean, use
oil or butter or a little of both. Butter or oil are on the other
hand unnecessary if the piece has a strip of fat. If the
piece has a strip of fat on one side only, put it in the oven
with this side upwards; when melting the fat will grease
the lower side sufficiently.
Red meat should be removed from the fridge one hour
before cooking otherwise the sudden change of temperature could cause it to become tough. A roast,
especially if of red meat, must not be salted at the
beginning of cooking as salt causes juices and blood to
seep out of the meat, thus preventing the formation of a
well-browned crust.
It is advisable to salt the outside of the meat after just
over half the cooking time.
Place the roast in the oven in a dish having a low rim; a
deep dish shields heat.
Meat can be placed on an ovenproof dish or directly on
the grill, under which the dripping pan will be inserted to
collect juice. Ingredients for gravy should only be put in
the dish immediately if cooking time is brief, otherwise
they should be added during the last half hour.
Begin cooking rare meat at a high temperature, reducing
the temperature to finish cooking the inside.
The cooking temperature for white meat can be moderate throughout.
The degree of cooking can be checked by pressing the
meat with a fork; if it does not give the meat is cooked.
At the end of cooking it is advisable to wait at least 15
minutes before cutting the meat in order that the juices
are not lost.
Before serving plates can be kept warm in the oven at
minimum temperature.
For the cooking of fish:
Cook small fish from start to finish at a high temperature. Cook medium-sized fish initially at a high temperature and then gradually lower the temperature.
Cook large fish at a moderate temperature from start to
finish.
Check that baked fish is cooked by gently lifting one side
of the gut; the meat must be white and opaque
throughout, except in the case of salmon, trout or similar.
Grilling
The following types of meat are suitable for grilling.
Mostly meat or offal cut in slices or pieces of various
sizes, but not usually very thick, poultry cut in half and
flattened, fish, some vegetables (e.g. courgettes,
aubergines, tomatoes, etc.), skewers of meat or fish and
seafood.
Meat and fish to be grilled should be lightly brushed with
oil and always placed on the grill; meat should be salted
upon completion of cooking; whereas fish should be
salted on the inside before cooking. The grill should be
positioned in the guides nearest or furthest from the grill
element according to the thickness of the meat, in order
to avoid burning the surface and cooking the inside
insufficiently.
14
The formation of smoke caused by drops of juice and fat
can be avoided by pouring 1 or 2 glasses of water into
the dripping pan.
The grill can also be used to brown, toast bread and grill
certain types of fruit, such as bananas, halved grapefruit,
slices of pineapple, apples, etc. Fruit should not be
placed too near the source of heat.
Cooking times
Cooking times can vary according to the type of food, its
consistency and its volume. It is advisable to watch
when cooking for the first time and check results since
when preparing the same dishes, in the same conditions,
similar results are obtained.
The “TABLE OF COOKING TIMES” relating to cooking
in the oven and by grill is provided as a guide.
Experience will show possible variations to the values
set out in the table.
Nevertheless carefully follow the indications given
in the receipe you intend to follow.
Attention: do not place any utensils such as dripping
pan, cake tins, casseroles, pyrex dishes, aluminium foil
or other on the base of the oven when the oven is in use.
A stagnation of heat would result which would compromise the results of cooking and could damage the oven
enamel.
Cooking with the turnspit
— Place the spit-support frame into the second runner
from the bottom of the oven (see figure).
— Pierce and secure well food on the spit.
— Pour some water in the dripping pan and place it on
the first shelf level.
— Fit the spit tip into the spit motor drive in the back of
the oven and lay its front part on the frame groove.
— Remove the spit handle.
— Turn the oven function control knob on symbol
.
Leave the oven door closed.
15
Cooking tables
These charts are intended as a guide only. It may be necessary to increase or decrease the temperature to suit your
individual requirements. Only experience will enable you to determine the correct setting for your personal requirements.
Cooking times do not include pre-heating time.A short oven pre-heating (about 10 minutes) is necessary before any cooking.
Traditional cooking and fan cooking
Weight (gr.)
Traditional Cooking
1000
500
500
250
1000
1200
1000
1500
1500
1500
1500
2000
1200
1200
1000
4000
1500
3000
1200
1500
800
1200
1500
Fan Cooking
Cooking
time
TYPE OF DISH
Level
Temp.
4
3
2
1
CAKES
Whisked recipes
Shortbread dough
Butter-milk cheese cake
Apple cake
Strudel
Jam-tart
Fruit cake
Sponge cake
Christmas cake
Plum cake
PASTRIES
Small cakes
Biscuits
Meringues
Buns
Pastry: Choux
BREAD AND PIZZA
White bread
Rye bread
Bread rolls
Pizza
FLANS
Pasta flan
Vegetable flan
Quiches
Lasagne
Cannelloni
MEAT
Beef
Pork
Veal
English roast beef
rare
medium
well done
Shoulder of pork
Shin of pork
Lamb
Chicken
Turkey
Duck
Goose
Rabbit
Hare
Pheasant
FISH
Trout/Sea bream
Tuna fish/Salmon
NOTES
Level
°C
4
3
2
1
Temp.
°C
minutes
2
2
1
1
2
2
1
1
1
1
170
170
160
180
175
175
175
175
170
170
2
2 (1 and 3)*
2
2 (1 and 3)*
2
2 (1 and 3)*
1
2
1
1
160
160
150
170
150
160
160
160
160
160
45 ~ 60
20 ~ 30
60 ~ 80
40 ~ 60
60 ~ 80
30 ~ 40
45 ~ 60
30 ~ 40
40 ~ 60
50 ~ 60
In cake mould on the shelf
In cake mould on the shelf
In cake mould on the shelf
In cake mould on the shelf
In cake tin on the shelf
In cake mould on the shelf
In cake mould
In cake mould on the shelf
In cake mould on the shelf
In cake mould on the shelf
2
3
2
2
2
170
190
100
190
200
2 (1 and 3)*
3
2
2
2 (1 and 3)*
160
170
100
180
190
25 ~ 35
15 ~ 25
90 ~ 120
12 ~ 20
15 ~ 25
In baking tray
In baking tray
In baking tray
In baking tray
In baking tray
1
1
2
1
190
190
200
200
2
1
2
2 (1 and 3)*
180
180
175
190
40 ~ 60
30 ~ 45
20 ~ 35
15 ~ 30
2 pieces in baking tray
In bread pan on the grid
6-8 rolls in baking tray
On baking tray on the grid
2
2
1
2
2
200
200
200
180
200
2 (1 and 3)*
2 (1 and 3)*
2 (1 and 3)*
2
2
175
175
180
160
175
40 ~ 50
45 ~ 60
35 ~ 45
45 ~ 65
40 ~ 55
In mould on the shelf
In mould on the shelf
In mould on the shelf
In mould on the shelf
In mould on the shelf
2
2
2
190
180
190
2
2
2
175
175
175
50 ~ 70
100 ~ 130
90 ~ 120
On shelf and dripping pan
On shelf and dripping pan
On shelf and dripping pan
2
2
2
2
2
2
2
2
2
2
2
2
2
210
210
210
180
180
190
190
180
175
175
190
190
190
2
2
2
2
2
2
2
2
2
2
2
2
2
200
200
200
170
160
175
175
160
160
160
175
175
175
50 ~ 60
60 ~ 70
70 ~ 80
120 ~ 150
100 ~ 120
110 ~ 130
60 ~ 80
210 ~ 240
120 ~ 150
150 ~ 200
60 ~ 80
150 ~ 200
90 ~ 120
On grid and dripping pan
On grid and dripping pan
On grid and dripping pan
With rind-in dripping pan
2 pieces-in dripping pan
Leg-in dripping pan
Whole-in dripping pan
Whole-in dripping pan
Whole-in dripping pan
Whole-in dripping pan
Cut in pieces
Cut in pieces
Whole
2
2
190
190
2 (1 and 3)*
2 (1 and 3)*
175
175
30 ~ 40
25 ~ 35
3-4 fishes
4-6 fillets
(*) If you need to cook more than one dish at the same time, we recommend you to place them on the levels quoted
between brackets.
If you wish to cook more than one dish at the same time, we suggest that you change the cooking levels of your dishes
during the last 5-10 minutes in order to obtain a more uniform colour of your dishes.
16
Cooking times do not include pre-heating time.
A short oven pre-heating (about 10 minutes) is necessary before any cooking.
Cooking Chart - Grilling
Level
Quantity
TYPE OF DISH
Fillet steaks
Beef-steaks
Sausages
Pork chops
Chicken (cut in two)
Kebabs
Chicken (breast)
Hamburger
Fish (fillets)
Sandwiches
Toast
Pieces
Weight
4
4
8
4
2
4
4
6
4
4-6
4-6
800
600
—
600
1000
—
400
600
400
—
—
4
3
2
1
3
3
3
3
3
3
3
3
3
3
3
Temperature
Cooking time
(minutes)
°C
Upper
side
Lower
side
max
max
max
max
max
max
max
max
max
max
max
12 ~ 15
10 ~ 12
12 ~ 15
12 ~ 16
30 ~ 35
10 ~ 15
12 ~ 15
10 ~ 15
12 ~ 14
3~7
2~4
12 ~ 14
6~8
10 ~ 12
12 ~ 14
25 ~ 30
10 ~ 12
12 ~ 14
8 ~ 10
10 ~ 12
—
2~3
Cooking Chart - Pizza
Weight (gr.)
Level
700
500
500
4
3
2
1
TYPE OF DISH
Pizza, large
Pizza, small
Flat cake
Temperature
1
1
1
Cooking
time
°C
NOTES
minutes
200
200
200
15 ~ 25
10 ~ 20
15 ~ 25
in baking tray
in mould on the shelf
in baking tray
Grill turnspit
FOOD
Chicken
Roasts
Weight Shelf position Temp. °C
(Gramms)
1000
2
200
800
2
200
Minutes
50/60
50/60
17
Cleaning and maintenance
Before cleaning always allow the cooling fan
to cool the oven down before switching off at
the electricity supply.
This appliance cannot be cleaned with steam
or with a steam cleaning machine.
The Hob Top
The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little wasing up liquid
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
Pan Supports
The pan supports are dishwasher proof. If washing them
by hand, take care when drying them as the enamelling
process occasionally leaves rough edges. If necessay,
remove stubborn stains using a paste cleaner.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy
water, and remove marks with a mild paste cleaner. A
well moistened soap impregnated steel wool pad can
be used with caution, if the marks are particularly difficult
to remove.
After cleaning, be sure to wipe dry with a soft cloth.
Ignition electrode
The electric ignition is obtained through a ceramic
"electrode" and a metal electrode. Keep these
components well clean, to avoid difficult lighting, and
check that the burner crown holes are not obstructed.
The Hotplate
Spills onto the actual plate should be removed using warm
water and a soft brush, nylon or plastic scourer. To keep
the plate looking as new, hotplate conditioner can be
purchased from most hardware stores (follow the
manufacturer's instruction for use).
Alternatively, wipe the plate with a drop of olive oil on a
kitchen towel to avoid rust. It is important to note that
the plate will smoke a little and produce a slightly
unpleasant odour when next used.
Drying
Important: After cleaning, dry the hotplate thoroughly by
switching on to a low-medium setting for a few minutes.
18
Cleaning the oven
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives should
also be avoided.
• Never use steam or steam machines to clean the
appliance.
External cleaning
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
•
•
Household detergent and bleaches
Impregnated pads unsuitable for non-stick
saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Clean the outer and inner door glass using warm soapy
water. Should the inner door glass become heavily soiled
it is recommended that a cleaning product such as Hob
Brite, or Bar Keepers Friend is used.
Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm.
Wipe the oven over with a soft cloth soaked in warm
soapy water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
Oven lamp replacement
Disconnect the appliance from the electricity
supply.
If the oven bulb needs replacing, it must comply with
the following specifications: electric power, 15 W/25 W;
electric rate, 230 V (50 Hz); resistant to temperatures
of 300°C; connection type: E14. These bulbs are
available from your local Service Force Centre.
!
To replace the faulty bulb:
1. Ensure the oven is disconnected from the electrical
supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace it with the new
one.
4. Refit the glass cover.
5. Reconnect to the electrical supply.
19
The Oven Door and its gasket
Before cleaning the oven door, we recommend you to
remove it from the oven.
Proceed as follows:
1. open the oven door completely;
2. find the hinges linking the door to the oven (see
picture 1);
3. unlock and turn the small levers located on the two
hinges (see picture 2);
4. handle the door by its left- and right-hand sides,
then slowly turn it towards the oven until it is halfclosed (see picture 3);
5. gently pull the oven door off its site (see picture 3);
6. place it on a steady plan;
!
Clean the oven door glass with warm soapy water and a
softh cloth only. Never use harsh abrasives.
Once the cleaning is carried out, refit the oven door,
following the procedure in reverse.
1
2
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not observed
the glass panel may shatter.
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Centre
who will be pleased to advise further.
Models in stainless steel or aluminium:
We recommend to clean the oven door using only a wet
sponge and dry it up after cleaning with a soft cloth.
Never use steel wool, acids or abrasive products as they
can damage the oven surface.
Clean the oven control panel following the same
precautions.
The correct operation of the oven is ensured by a gasket
placed round the edge of the oven cavity.
•
Periodically check the condition of this gasket. If
necessary, clean it without using abrasive cleaning
products.
•
If the gasket shows to be damaged, call you local
Service Centre. Do not use the oven until it has been
repaired.
How to regulate the storage
drawer door magnets
The storage drawer door can be best regulated by
adjusting the magnets in the following way (see picture):
- turn the magnets anticlockwise (the magnets will
extend) to increase the seal of the storage drawer door;
- turn the magnets clockwise (the magnets will get
shorter) to obtain the opposite effect.
20
3
Oven Shelves and Shelf Supports
To clean the oven shelves, soak in warm soapy water
and remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
The shelf supports can be removed for easy cleaning.
Proceed as follows:
1) remove the front screw while keeping the shelf support
in position with the other hand (see diagram 1);
2) disengage the rear hook and take off the shelf support
(see diagram 2);
3) once the cleaning is carried out, refit the shelf supports
following the procedure in reverse.
Please, ensure the retaining nuts are secure when
refitting the shelf support.
1
2
Lid cleaning
The crystal lid can be dissasembled to allow a better
cleaning ( see picture).
Clean the crystal lid only with warm water and avoid the
use of rough cloths or abrasive substances.
After a proper cleaning, carefully reposition the lid
into its hinges.
Balancing the lid
Appliances provided with crystal lids are equipped with
specially balanced springs, inserted in the hinges at the
back of the appliance, to allow the lid to be closed
smoothly and easily.
You can use a screwdriver to adjust the closure of the
lid. The necessary force for opening/closing the lid can
be increased by turning the adjusting screw 2 or 3 times
as shown in the diagram.
Controls - Sundries
Periodically check the condition of the flexible pipe of
gas connection and make it replaced by skilled
technicians as soon as it shows abnormalities. Annual
replacement is recommended.
Have the cocks periodically lubricated by skilled
technicians. In case of unusual working have the range
checked by skilled technicians.
21
Something not working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Centre.
!
SYMPTOM
There is no spark when lighting the gas.
SOLUTION
" Check that the unit is plugged in and the electrical
supply is switched on.
" Check the mains fuse has not blown.
" Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
!
The gas ring burns unevenly.
" Check the main jet is not blocked and the burner
crown is clear of food particles.
" Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
! The oven does not come on.
" Check that a cooking function has been selected.
" Check that the oven door is completely closed.
" Check that he minute minder control knob is in the
position.
! The oven light does not come on.
" Check that the socket switch or the switch from the
mains supply to the appliance are ON.
" Select a function with the oven function control
knob.
! It takes too long to finish the dishes, or they are
cooked too fast.
! Steam and condensation settle on the food and the
oven cavity.
" Check the light bulb, and replace it if necessary
(see "Oven lamp replacement").
" The temperature may need adjusting.
" Refer to the contents of this booklet, especially to
the chapter “Hints and Tips for using the oven”.
! The oven fan is noisy.
" Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
" Check that shelves and bakeware are not vibrating
in contact with the oven back panel.
If, after following all the above checks the appliance still does not work, call your local Service Centre givin them all the
necessary information, such as model, product number and serial number of the appliance.
Service and spare parts
If after the checks listed in the previous chapter, the
appliance still does not work correctly, contact your
locals Service Centre, specifying the type of
malfunctioning, the appliance model (Mod.), the product
number (Prod. No.) and the serial number (Ser. No.)
marked on the identification plate.
This plate is placed on the front external edge of the oven
cavity.
Original spareparts, certified by
the product manufacturer and
carrying this symbol are only
available at our Service Centre
and authorized spareparts shops.
22
Instructions for the installer
Technical data
Oven
Dimensions of the appliance
Top element
Bottom element
Top + Bottom element
Inner grill
Full grill
Pizza
Oven fan
Turnspit motor
Oven lamp
Total rating
800 W
1000 W
1800 W
1650 W
2450 W
2650 W
25 W
4W
25 W
2700 W
Total appliance electric rating (hob + oven)
Voltage tension (50 Hz)
4,700 W
230 V
Height
Width
Depth
Oven capacity
Appliance
850 mm
600 mm
600 mm
56 l
Class 1 and
Category:
Class 2
Sub-Class 1
I3+
Appliance set for use with gas type:
LPG 28-30/37 mbar
Hob
Rear left burner (semi-rapid)
Front left burner (ultra-rapid triple crown)
Front right burner (auxiliary)
2000 W
4000 W
1000 W
Rear right cast iron hotplate Ø 180 mm
2000 W
Burner characteristics
Burner
Normal power
Reduced power
LPG
28-30/37 mbar
Mark
1/100
G30/G31
kW
kW
Auxiliary
1,0
0,33
50
72
Semi-rapid
2,0
0,45
71
145
Ultra-rapid triple crown
4,0
1,20
98
290
g/h
By-pass diameters
Burner
Auxiliary
Semi-rapid
Ultra rapid triple crown
Ø By-pass
in 1/100
of mm.
28
32
56
23
Installation
This appliance cannot be positioned on a
base.
The following instructions are meant for a qualified
installer, in order that the operations of installation,
regulation, and service are executed according to the
existing regulations.
Before using the unit, take off the special protective layer
which protects the stainless steel and anodyzed tin
parts. Whenever changes are mode involving the
disconnection of the machine it is necessary to proceed
with maximum caution.
THE MANUFACTURING COMPANY DECLINES
ANY RESPONSABILITY FOR POSSIBLE
DAMAGES
RESULTING
FROM AN
INSTALLATION WHICH DOES NOT COMPLY
WITH THE RULES IN FORCE.
Installation environnement
Feet Assembly
1.
2.
3.
4.
5.
6.
Before installing the cooker, it is necessary to
assemble the supplied feet.
Remove the hob pan supports, the burner caps and
crowns and the oven accessories.
Carefully lean the cooker on its back, paying attention
not to cause any damage.
Adjust the feet height by unscrewing the bottom part
of each foot, until you obtain the required height (height
can be adjusted from 850 to 880 mm).
Insert the feet into the relevant holes indicated in the
diagram.
Lift the cooker in vertical position. Replace the crowns,
the burner caps, the hob pan supports and the oven
accessories.
If necessary, adjust the cooker horizontally levelling
by turning the bottom part of the feet, until the
appliance is completely stable.
Warning - This unit can be installed and can work only
in constantly ventilated rooms, according to rules in
force.
In order to make the gas unit work properly, it is
necessary that air sufficient to gas combustion can
naturally flow in the room. (The installer must follow the
rules in force).
The air flow into the room must come directly through
openings of external walls. These openings (or opening)
should be made in such a way not to be occluded both
from inside and outside.
Installation and maintenance must be carried out by a
qualified technician, in compliance with the rules in force.
The electric coonection must be carried out in
compliance rules in force.
Our responsability will not be involved in case of
accidents caused by a defective or non existent
earth connection.
Combustion products discharge
Gas cooking units must discharge combustion products
through hoods directly connected to flues or outside.
Positioning
500
Insertion possibility
In case of insertion of the appliance between kitchen
units, the dimensions to be respected are shown in the
picture.
When the kitchen is installed according to class 2, subclass 1 (i.e. built-in) for the gas connection use only
flexible metallic tubes conforming to rules in force.
FO 1076
24
650
100
This appliance has been designed to be placed close to
furniture units not exceeding the height of the working
level.
Gas connection
Gas connection must be carried out according to the
rules in force. The manufacturing company release the
unit, once tested, adjusted for the kind of gas stated
on the rating plate located on the back of the range,
next to connection pipe. Be sure that you are going to
connect the unit to the same kind of gas written on the
rating plate. For best efficiency and lowest
consumption, be sure that manifold gas pressure
respects the values in the table of burners
characteristics.
Connection using a rigid pipe or
a flexible metal pipe
To ensure higher safety, it is recommended to carry out
the connection to the gas system using rigid pipes (ex.
copper) or using flexible stainless steel pipes, to avoid
any stress to the unit. Gas feeding pipe fitting is Gc 1/
2. For this type of installation, connection to the gas
supply should be carried out using only and exclusively
flexible metallic tubes in conformity with rules in force.
Connection using flexible non
metal pipes
When the connection can be easily inspected in its full
extent, there is the chance to use a flexible pipe
according to the rules in force. The flexible pipe must
be tightly fixed using clamps according to the rules in
force.
The flexible pipe should be made ready for use in such
a way that:
- nowhere it can reach overtemperature, other than
room temperature, higher than 30°C; if the flexible
pipe, to reach the cock, must run behind the range,
it must be installed as shown in the diagram;
- it is no longer than 1500 mm;
- it shows no throttles;
- it is not subject to traction or torsion;
- it doesn't get in touch with cutting edges or corners;
- it can be easily inspected in order to check its
condition.
The control of preservation of the flexible pipe consists
in checking that:
- it doesn't show cracks, cuts, marks of burnings both
on the end parts and on its full extent;
- the material is not hardened, but shows its normal
elasticity;
- the fastening clamps are not rusted;
- expiry term is not due.
If one or more abnormalities are seen, do not repair the
pipe, but replace it.
YES
FLEXIBLE RUBBER
GAS PIPELINE
ELECTRIC WIRE
NO
FLEXIBLE RUBBER
GAS PIPELINE
ELECTRIC WIRE
IMPORTANT
Once installation is complete, check the perfect
seal of every pipe fitting, using a soapy solution,
never a flame.
25
Electrical connection
Any electrical work required to install this
cooker should be carried out by a qualified
electrician or competent person, in
accordance with the current regulations.
The unit is preset to work with a voltage of single phase
230 V.
Before making the connection make sure that:
— the energy power available in the user's house is
sufficient for the normal supply of this appliance (see
rating plate).
— the unit is correctly connected to earth through a
suitable plug and according to the installation country
Laws.
— the socket or the omnipolar switch used for the
connection must be easilv reached with the installed
appliance.
The appliance is supplied with electric cable, therefore
you will have to fit it with a standard plug, suitable for the
total electric load shown on the rating plate. The plug is
to be inserted into a suitable wall socket.
If you wish to directly connect to the mains, you have to
interpose an omnipolar switch with a minimum opening
between contacts of 3 mm, between the unit and the
mains, complying with the existing regulations. The
brown live wire (originating from the clamp of the
appliance junction box) must always be connected to the
phase of the mains supply. In any case, the supply cord
must be positioned in such a way as it doesn't reach in
any point a temperature higher by 50°C than the room
temperature.
Replacement of the electric
cable
Should the supply cord need to be replaced, use only
the following cable types: H07 RN-F, H05 RN-F, H05 RRF, H05 VV-F, H05 V2V2-F (T90), H05 BB-F. It is
necessary that the yellow/green earth wire is about 2 cm
longer than the live and neutral ones (see picture). After
the connection, test the heating elements for about 3
minutes to ensure that they are working correctly.
The manufacturer refuses any responsability in
cases where normal safety measures are not
observed.
26
Phase
Neutral
wire
Ground (yellow - green)
EKM6717X
0,79 kWh
0,78 kWh
56
43 min.
41 min.
1130 cm²
47
27
02/06
Grafiche MDM - Forlì
www.electrolux.co.ph
www.electrolux.co.th
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement