Aeg-Electrolux | 6310DK-M | User manual | Aeg-Electrolux 6310DK-M User Manual

6310 DK
Ceramic glass hob
GB
374 4225 13 / 11.04
INSTRUCTION BOOK
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
Your New Appliance
Thank you for purchasing an AEG appliance.
To enable you to use your new appliance efficiently and safely, please read
this instruction book carefully before installing or using the appliance, and
retain for future reference. Should the appliance be transferred to a new
owner please ensure this instruction book is left with the appliance in order
that the new owner can get to know the functions of the appliance and the
relevant warnings.
on the product or on its packaging indicates that this
The symbol
product may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of
this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
If you require further assistance or advice, please contact our Customer Care
Department either by letter or telephone:
Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough
SL1 1DZ
Tel:
08705 350350*
* calls to this number may be recorded for training purposes
2
23
Table of contents
Contents
Page no
For the user
Your new appliance ...................................................................................... 2
Safety information ........................................................................................ 4
Description of the product ......................................................................... 5
Operating instructions ................................................................................ 6
Pilot light ............................................................................................... 7
Residual-Heat indicator ........................................................................ 7
Advice and hints for using the cooking zones ....................................... 8
Cleaning and maintenance ....................................................................... 10
Splashguard ........................................................................................ 10
Stainless steel surfaces ....................................................................... 11
The ceramic glass hob ........................................................................ 11
Somthing not working ............................................................................... 17
Service and spare parts ............................................................................ 19
Guarantee conditions ................................................................................ 20
For the installer
Installation .................................................................................................. 13
Electrical connection ................................................................................. 15
Technical data ............................................................................................. 16
Unpacking .................................................................................................. 16
How to read the operating instructions:
1... 2...Step by step
Hint and tips
Safety information
22
Environmental information
3
Safety information
Child Safety
Before you move please contact your
nearest Customer Care centre, listed
below, to give them details of your new
home. They will then ensure that the
local service organisation is aware of
your move and able to look after you
and your appliances.
Young children must not be allowed to
tamper with the hob or play with the
controls.
France
Senlis
+33 (0) 44 62 29 29
Germany
Nürnberg
+49 (0) 911 323 2600
Italy
Pordenone
+39 (0) 1678 47053
Sweden
Stockholm
+46 (0) 8 738 79 10
UK
Slough
+ 44 (0) 1753 219899
Never use plastic or aluminum dishes
on the hob.
These warnings are provided in the
interests of your safety. Ensure you
fully understand them before installing
or using the appliance. Your safety is of
paramount importance. If you are
unsure about the meaning of these
warnings contact the Customer Care
Department for assistance.
Never leave the hob unattended while
deep fat frying, or heating fats and oils.
Installing
Do not install the hob if the ceramic
glass is damaged or cracked.
The hob gets hot when it is in use.
Children should be kept away until the
hob has cooled.
This hob must be installed according to
the instructions supplied. Any electrical
installation work must be undertaken
by a qualified electrician/ competent
person.
Maintenance and Cleaning
Only clean this hob in accordance with
the instructions given in this book.
Do not alter the specifications or
attempt to modify the appliance in any
way.
Service
Repairs carried out by inexperienced
persons may cause injury or serious
malfunction of the appliance. Repairs
must only be carried out by a
qualified/competent person. Contact
your local AEG Service Force Centre.
During Use
The hob is intended for domestic
cooking only. It is not designed for
commercial/industrial purposes.
Disposal
Ensure that all the control knobs are in
the OFF position when not in use.
Make the hob unusable by cutting off
the cable.
Do not use the hob if it is damaged in
any way. If a fault or crack becomes
visible, disconnect the hob immediately
from the electricity supply and contact
your local AEG Service Force Centre.
Dispose of any packaging material and
old appliances at an authorised
disposal site.
4
21
Guarantee conditions
AEG offer the following guarantee to
the first purchaser of this appliance:
1. The guarantee is valid for 12
months commencing when the
appliance is handed over to the first
retail purchaser, which must be
verified by purchase invoice or
similar documentation.
2. The guarantee covers all parts or
components which fail due to faulty
workmanship or faulty material.
The guarantee does not cover
appliances where defects or poor
performance are due to misuse,
accidental damage, neglect, faulty
installation, unauthorised
modification or attempted repair,
commercial use or failure to
observe requirements and
recommendations set out in the
instruction book.
3. Should guarantee repairs be
necessary the purchaser must
inform the nearest AEG Service
Force Centre. AEG reserves the
right to stipulate the place of repair
(i.e., the customer's home, place of
installation or AEG workshop).
4. The guarantee or free replacement
includes both labour and materials.
5. Repairs carried out under guarantee
do not extend the guarantee period
for the appliance. Parts removed
during guarantee repairs become
the property of AEG.
Description of the product
6. The purchaser's statutory rights are
not affected by this guarantee.
Residual-heat indicator
European guarantee
If you should move to another country
within Europe then your guarantee
moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you
first purchased your product.
The guarantee is for the same period
and to the same extent for labour and
parts as exists in the new country of
use for this brand or range of products.
Pilot light
Control knobs
Single cooking
zone
This guarantee relates to you and
cannot be transferred to another user.
The product is installed and used in
accordance with our instructions and is
only used domestically, i.e. a normal
household.
The product is installed taking into
account regulations in your new
country.
20
5
Dual cooking zone
Operating instructions
Service & spare parts
In the event of your appliance requiring service, or if you wish to purchase spare
parts, contact your local AEG Service Force Centre by telephoning:
Control knob (to the left)
Control knob for regulating the
dual cooking zone at the rear
Pilot light
Control knob for regulating the
single cooking zone at the front.
08705 929 929
Your call will automatically be routed to the Service Centre covering your post
code area.
In-guarantee customers should ensure that the recommended checks under the
heading "Something Not Working" have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Regulating
The regulating of heat is step-free for
both zones on a scale from 1 to 9.
“1”
Represents lowest heat
“9”
Represents maximum heat.
“0”
Represents “OFF”.
Please note that proof of purchase is required for in-guarantee service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning. When you
contact us we need to know:
Operating the dual zone: When you
switch on the dual zone only the centre
of the cooking zone will operate. Select
the required setting.
1.
2.
3.
4.
To select both cooking zones Turn the
control knob past “9” to stop, turn then
back to the required setting.
Your name, address, post code and telephone number
Clear and concise details of the fault.
Date of purchase
The model and serial number
This information can be found on the rating plate.
To return to centre zone only: Turn the
control knob back to “0”. Turn the
control knob on again and choose the
required setting.
Customer Care
For general enquires concerning your AEG appliance or for further information
on AEG products, please contact our Customer Care Department at the address
below or visit our website at www.aeghome.co.uk
Do not use the ceramic hob if the
glass is damaged.
If a fault or crack appears during
cooking disconnect the hob
immediately and contact AEG
Service Force
Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough, Berkshire
SL1 1DZ
Tel 08705 350350*
*calls to this number may be recorded for training purposes
6
19
If after all these checks, your hob still does not operate correctly, contact
your local AEG Service Force Centre.
In-guarantee customers should ensure that the above checks have been made
as the engineer will make a charge if the fault is not a mechanical or
electrical breakdown.
Please note that it will be necessary to provide proof of purchase for any inguarantee service calls.
Pilot light
Pilot light is activated when either of
the zones are turned on, and will
remain on until the cooking zones are
switched off.
Residual-Heat indicator
Each plate has a residual heat
indicator which remains on as long as
the temperature of the cooking zone
exceeds 80˚C, even if the cooking zone
is switched off.
Settings for ordinary cooking zones
Step
Function
0
The cooking zone is switched off
1-2
Keeping warm
3-4
Gentle simmering
5-6
Simmering
7-8
Frying / browning
9
Bringing to the boil / quick frying / deepfrying
This table should be used as a guide only. The settings
depend on the saucepan you use, quantity and contents. After
a while you will learn to choose the correct settings. See also
the section “Advice and hints for using the cooking zones”.
18
7
Something not working
Advice and hints for using the
cooking zones
If you use the advice below
you will save energy and
make your cleaning tasks
easier.
Adjust the cooking zones
correctly. Select the highest setting
for the cooking zones until the food is
brought to the boil. Then reduce the
setting as far as possible, without the
food going off the boil.
over will burn onto the hot
cooking zone.
If the hob is not working correctly, please carry out the following checks before
contacting your local AEG Service Force Centre.
Saucepans with very
shiny/bright bases will
prolong the cooking time
slightly compared with
cooking utensils with
matt/dark bases.
IMPORTANT: If you call out an engineer to a fault caused by incorrect use or
installation, a charge will be made even if the hob is under guarantee.
Use a tightly fitting lid on the
saucepan. Without a lid you
use more than three times as
much electricity.
Use level saucepans. An
uneven saucepan may
increase the electricity
consumption by up to 50 per
cent. Check whether your
saucepans have level bases
by placing the item in question
upside down on a work top and
positioning a ruler on the base.
A curved base, both inwards and
outwards, will prolong the
cooking time and increase the
energy consumption
The saucepan should match
the cooking zone – or be
slightly larger. Remember
that a large saucepan can also
hold small quantities. If the
diameter of the base is too small,
the energy consumption will
increase, and any food boiling
8
Sympton
Solution
The hob is not working
Check that the appliance is connected
to the eletricity supply.
Check that the main house fuse has not
blown. Replace if necessary.
The fuses keep blowing
Contact your local AEG Service Force
Centre
The cooking zones do not heat
sufficiently
The cooking utensils must match the
size of the cooking zone. Check that
the cooking utensils have level bases
by holding them against the edge of the
work top, for example. Bring a litre of
water to the boil in a saucepan with a
lid. The cooking zone should be
adjusted to the highest setting.
The boiling time on the 12 cm cooking
zone is approx. 25 min.
The boiling time on the 14 cm cooking
zone is approx. 13 min.
The boiling time on the 18 cm cooking
zone is approx. 10 min.
17
Technical data
Do not slide saucepans across the
surface of the hob - always lift the pan
when placing it on, or removing it
from the ceramic surface.
Cell Voltage 240 V
Electrical connection
240V - 50Hz
Wipe the bottom surface of the pots
and pans with a clean dry cloth before
placing them on the ceramic surface.
This helps to reduce cleaning and
prevents scratching the hob glass.
Total wattage 2900W
Instant heat effect 12/18 cm 700/1700 W
Instant heat effect 14 cm 1200 W
This unit is labelled to indicate
conformity with the low voltage
directive (73/23/EEC) and the EMC
directive (89/336/EEC).
Wipe off spills whilst the hob is warm.
Unpacking
Serial number
Check that the hob has no faults and
is undamaged on delivery.
You will find the serial number of the
hobs on the rating plate, which is on
the underside of the hob.
We recommned you write this number
on the cover of this instruction, so that
you have this information to in the
case of any service requirements.
Transport damage
Any damage from transport which
you have not carried out yourself must
be reported to the retailer within one
week of receipt.
16
Select the highest setting for the
cooking zones until the food is brought
to the boil, then reduce the setting.
Use saucepans with an even base. An
uneven based saucepan may increase
the electricity consumption by up to
50%.
The saucepan should match the
cooking zone or be slightly larger.
Use a tightly fitting lid on the saucepan
to reduce electricity consumption.
9
Cleaning and maintenance
Electrical connection
The electrical connection may only be
performed by a qualified electrician/
competent person. The electrical
connection must be carried out in
accordance with prevailing regulations
for appliances using heavy current.
The connection must comply with any
specific requirements specified by the
local electricity supply authority.
For reasons of hygiene and
safety, the cooking zones
must be kept clean. Grease
stains and spilled food
generate smoke when heated,
and can even cause fire.
Splashguard
The splashguard can be removed to
make it easier to clean the surface.
There must be no interference with
any of the unit’s electrical parts.
What to do:
1. Hold the splashguard as shown
in the diagram.
2. Lift the splashguard straight up
3. Clean the top surface as
described in “cleaning the steel
surface”.
Be aware of the two retaining
pegs, which are sharp.
4. Replace the splashguard in
position ENSURE that it is
fitted the correct way round.
The cable is mounted in the pegs as
shown.
Unscrew the cover while connecting
the cables.
A unit led directly to the power point
or the outlet rose.
More units may be connected via one
or more junction boxes.
The cable must be connected via an
external switch with a contact
separation of at least 3 mm in each
pole.
Never use hard or sharp
implements to lift off the
splashguard.
Do not wash the splashguard
in a dishwasher.
Cover
Please observe these instructions,
otherwise the warranty will not
cover any damage that may occur.
Single-phase zero-earth
Cable type 1,5 mm² HO5VV-F.
The cable outside diameter must be
between 7,5 and 10,5 mm.
The hob must not be used
with the splashguard off.
10
15
It is not necessary to attach the
reinforcement beam to the work top
surface, as it is held in place by a
specially designed moulding, which is
incorporated in the hob units flanges.
Stainless steel surfaces
Clean the appliance after use with a
soft cloth well wrung out in warm
water, use a small amount of liquid
detergent for stubborn soiling.
Stainless steel parts may become straw
coloured with use, use a proprietary
stainless steel cleaner to remove this
straw discolouration.
The units externally measured
length
145 mm:
Cooker hood
Never use metal wool, metal sponges
or other abrasive cleaning agents.
290 mm:
Two-zone ceramic-top electric hob
Two-burner gas hob
Grill
Fryer
Wok
The ceramic glass hob
3. Wipe the ceramic hob clean with
a damp cloth or kitchen roll.
Tough stains can be removed by
rubbing the stain hard with
kitchen roll.
4. Wipe off remaining cleaning
agent with a damp cloth.
5. Wipe with a dry cloth, if
required.
Make sure that the ceramic hob is dry
when you heat it up again. Ceramic
hobs can develop rainbow-like stripes
if heated while damp.
Immediately scrape off stains caused
by food which has boiled over using
the scraper supplied with the hob,
spilled sugar, dishes containing sugar
(jam, juice, etc.), melted plastic and
aluminium foil while the ceramic hob
is still hot. If the ceramic hob is
allowed to cool it may become
damaged. A dirty ceramic hob
decreases the heat transfer between
cooking zones and cookware.
580 mm:
Four-zone ceramic-top electric hob
Four-burner gas hob
725 mm:
Four-zone ceramic-top electric hob
Installation of a single unit
After use the cooking zones should be
wiped with a damp cloth with washing
up liquid. For severe soiling you can
follow these steps:
When mounting a single unit, be it a
half-or full size unit, in a
worktopsurface which is thicker than
30 mm, it is necessary to make a
special notch in both sides of the cutout hole, as shown in the adjacent
drawing.
The purpose of these notches is to
create space for the electrical cables.
1. Remove stains etc., with the
ceramic hob scraper.
2. Make sure that the ceramic hob
has cooled down. Use a ceramic
cleaning agent, such as vitroclen.
14
11
Installation
The decorative pattern on the ceramic
surface can become scratched and
marred with use, depending upon
maintenance, but does not adversely
affect performance.
Caution: In order to avoid a hazard this
appliance must be installed according to
these instructions for installation
Min. 47 mm
Such blemishes are not covered by the
warranty and do not affect the
operation of the hob.
The appliance unit can be mounted in
any type of kitchen with a work top
whose thickness is between 28 mm and
40 mm.
Clearance
Spills and melts must be removed
immediately, while the surface is still
warm, using the scraper supplied with
the unit. Especially damaging are melted
plastic, aluminum, or any foodstuff
containing sugar, including natural sugar,
as these can create permanent
“pockmarks” and craters on the ceramic
surface. After scraping polish thoroughly
with the cleaning agent supplied with the
unit.
Utensils which have been in contact with
the above-mentioned melted materials
must be cleaned throughly before used
again on the ceramic-top hob unit.
Defects in the ceramic surface which can
be related to the above are not covered
by the warranty.
Warning:
Aluminum foil and plastic utensils are
not to be placed on hot surfaces.
The surface may not be used for storage.
Do not stare at the heating units when
in operation.
12
The distance between the top side of the
work top and the carpentry underneath
must be at least 47 mm.
Fixing
Screw the fixing brackets out to such an
extent that they can be turned in under
the work top. Tighten the brackets on to
the work top with an ordinary
screwdriver.
Minimum distance
to side wall:
150 mm
Cut-out measurements
One rectangular hole is sawn out for the
appliance combination chosen.
The depth of the cut-out for any unit is:
490 mm
Length of hole = sum of all units`
externally measured length, less 20 mm.
Reinforcement
beams
Mounting of Reinforcement
Beams
A reinforcement Beam, with supporting
flanges at each end, is included with
each two-burner unit. For unit
combinations, a reinforcement beam
must be used between each unit.
13
Minimum distance
to rear wall (nonflammable material):
50 mm
Download PDF

advertising