Aeg-Electrolux | FM6800TYAN | User manual | Aeg-Electrolux FM6800TYAN User Manual

FM 6800TYAN
User manual
Induction Teppan Yaki
2
Dear Customer
Thank you for choosing one of our high-quality products.
With this appliance you will experience the perfect combination of functional
design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best performance and control - indeed we are setting the highest standards of excellence.
In addition to this you find environmental and energy saving aspects as an integral part of our products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a
safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
3
The following symbols are used in this user information:
Warning! This must be read! Important advice for the safety of persons and
information on avoiding damage to the appliance
General information and advice
2
Information on environmental protection
1
z
Dangerous voltage
Contents
3
Contents
Operating Instructions
4
Safety instructions
4
Description of the Appliance
The most important features of your appliance
Teppan Yaki layout
Control panel layout
Touch Control sensor fields
Displays
Residual heat indicator
Operating the appliance
Preparing food with the Teppan Yaki
Temperature range
Switching the appliance on and off
Setting the temperature
Using the child safety device
Using the timer
Automatic switch off
Tips for cooking with the Teppan Yaki
Using fats and oils
Table
Cleaning and care
6
6
7
7
8
8
8
9
9
9
10
10
11
12
14
15
15
15
18
What to do if …
19
Disposal
20
Installation Instructions
Safety instructions
Assembly
21
21
22
Installing more than one Frontline hob
Rating Plate
Guarantee/Customer Service
26
30
31
Service and Spare Parts
35
4
Operating Instructions
Operating Instructions
1 Safety instructions
Please comply with these instructions. If you do not, any damage resulting is not
covered by the warranty.
Correct use
• Persons (including children) who, due to their physical, sensory or mental capacity or their inexperience or lack of knowledge are unable to use the appliance safely should not operate this appliance without the supervision or
instruction of a responsible person.
• Do not leave the appliance unattended during operation.
• This appliance should be used only for normal domestic cooking and frying of
food.
• The appliance must not be used as a work surface or as a storage surface.
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance.
Child safety
• Small children must be kept away from the appliance.
• Only let bigger children work on the appliance under supervision.
• To avoid small children and pets unintentionally switching the appliance on,
we recommend activation of the child safety device.
General safety
• The appliance may only be installed and connected by trained, registered service engineers, or competent persons.
• Built-in appliances may only be used after they have been built in to suitable
built-in units and work surfaces that meet standards.
• In the event of faults with the appliance or damage to the glass ceramic
(cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply to prevent the possibility of an electric
shock.
• Repairs to the appliance must only be carried out by trained registered service
engineers.
Safety instructions
5
Safety during use
• Overheated fats and oils can ignite very quickly. Warning! Fire hazard!
• IMPORTANT Risk of burns! Fat or oil added to the cooking surface which has
already been heated ignites quickly and can spit.
• There is the risk of burns from the appliance if used carelessly.
• Remove stickers and film from the glass ceramic and the cooking surface.
• Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
• Switch cooking zone off after every use.
• Users with implanted pacemakers should keep their upper body at least 30 cm
from the cooking zones that are switched on.
• The ventilation gap of 5mm between the worktop and front of the unit underneath it must not be covered.
• Do not use pots and pans made of cast iron or those with damaged bases that
are rough and have burrs. Pushing these about can cause scratches.
Safety when cleaning
• For cleaning, the appliance must be switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or high-pressure cleaning equipment is not permitted.
How to avoid damage to the appliance
• The ceramic glass can be damaged by objects falling onto it.
• The edge of the ceramic glass can be damaged by being knocked by the cookware.
• Objects that melt and things that boil over can burn on and should be removed straight away.
Special notes for the Teppan Yaki
• During operation, noises can be caused by the grill expanding. This is not a defect in the cooking surface and its operation is not affected.
• If the grill is used frequently, a slight depression may form in the middle of the
cooking surface where the two zones meet. This is not a defect in the cooking
surface and its operation is not affected. Therefore:
– Do not place pots and pans over the transition between the two zones, as
the depression can make them unsteady.
– Frying on the transition between the zones can result in uneven browning
(e. g. with pancakes).
6
Description of the Appliance
Description of the Appliance
The most important features of your appliance
• The cooking surface is 11 mm thick. It consists of two layers of stainless steel
with a layer of aluminium between them. This therefore has a good thermal
capacity, which prevents a rapid decrease in temperature, for example, when
preparing meat from the refrigerator.
• The cooking surface is divided into two separately controlled grilling zones of
the same size (see “Teppan Yaki layout”).
• The groove around the edge serves three important functions:
– It reduces the temperature on the installation surfaces so much that the
cooking surface can be installed into various types of kitchen worktops.
– The indentation of the groove absorbs some of the expansion of the heated
cooking surface.
– Minor food remnants and liquids can easily be fed into the groove and removed.
• The desired temperature can be kept constant by the thermostat with a readable temperature setting. This prevents overheating of the food and permits
low-fat cooking with retention of nutritional values.
• The food is prepared (heated) directly on the cooking surface, with or without
fat. There is also the option of cooking with pots or pans.
• The heating time, e.g. to 180 °C, is approx. 4 minutes. The cooling down time,
e.g. from 180 °C to 100 °C, is approx. 25 minutes, or to 60 °C approx.
60 minutes.
• The cooking surface must always be preheated.
Description of the Appliance
7
Teppan Yaki layout
rear grilling zone
2800 W
front grilling zone
2800 W
Frontline strip
Control panel
Control panel layout
Temperature display for
rear grilling zone
Child lock pilot
light
Child lock
Timer indicator
Pilot light for
temperature preset
Temperature selection
for rear grilling zone
160 °C / 180 °C
temperature preset
Temperature display for
front grilling zone
Pilot light for
temperature preset
Timer
Timer selection
On/Off pilot light
Temperature selection
for front grilling zone
160 °C / 180 °C
temperature preset
On/Off
8
Description of the Appliance
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. You control the
functions by touching the sensor fields.
Touch the sensor fields from above, without covering other sensor fields.
Sensor field
On / Off
Increase settings
Reduce settings
Timer
Increase settings
Reduce settings
Child lock
160 °C temperature preset
180 °C temperature preset
Function
Switches appliance on and off
To increase the temperature
To reduce temperature
Timer selection
To increase Timer time
To reduce Timer time
Locking control panel for children
To switch on 160 °C temperature preset
To switch on 180 °C temperature preset
Displays
Display
50 220
Temperature display in
degrees Celsius
Fault
Residual heat
Child safety device
Automatic switch off
Description
Appliance is switched on
Temperature is set
Malfunction has occurred
Cooking zone is still hot
Child safety device is engaged
Switch off is active.
Residual heat indicator
1
3
Warning! Risk of burns from residual heat. After being switched off, the cooking zones need some time to cool down. Look at the residual heat indicator
.
Residual heat can be used for melting and keeping food warm.
Operating the appliance
9
Operating the appliance
Preparing food with the Teppan Yaki
3
3
The foods are prepared (heated) directly on the cooking surface, with or without
fat. There is also the option of cooking with pots or pans.
However, if pots and pans are used on the cooking surface, the warm up time is
markedly longer than on glass ceramic, gas or cast-iron plates.
Accompaniments, e.g. sauces, rice, etc., can be cooked or kept warm in pots or
pans placed directly on the cooking surface.
We do not recommend boiling large quantities on the cooking surface, such as,
e.g. for spaghetti.
Do not hestitate to turn over or remove food with a spoon while cooking on the
cooking surface. Working marks on the cooking surface are normal and do not
affect the operation of the appliance.
The induction Teppan Yaki may make noises during operation. These noises do
not indicate a fault in the appliance and its operation is not affected in any way.
Temperature range
3
You can set the cooking surface to the temperature you want in 10° steps in the
range 50 °C to 220 °C.
The heating up time, e.g. to 180 °C, is approx. 4 minutes.
10
Operating the appliance
Switching the appliance on and off
To switch on
To switch off
3
Control panel
Touch for 2 seconds
Touch for 2 seconds
Display
/
/ none
Pilot light
lights up
goes out
After switching on, within approx. 10 seconds a heat setting or a function must
be set, otherwise the appliance automatically switches itself off.
Setting the temperature
To increase
To decrease
To switch off
3
Control panel
Touch
Touch
Touch and
the same time
Display
50 to 220
220 to 50
0
If a temperature is selected, the indicator flashes until the desired temperature is
reached. When the selected temperature is reached, a signal sounds. The indicator stops flashing and displays the selected temperature
Operating the appliance
11
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Deactivate the child safety device
Step
Control panel
Display/Signal
1.
Switch appliance on
2.
Touch for 4 seconds
0 lights up
Appliance switches off. The child safety device is switched off.
Switching on the child safety device
Step
Control panel
Display/Signal
1.
Switch on appliance. (Do not set a
heat setting.)
2.
Touch for 4 seconds
Appliance switches off. The child safety device is switched on
Overriding the child safety device
The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards.
Step
Control panel
Display/Signal
1.
Switch appliance on
2.
Touch
and of a grill zone the
/ Acoustic alarm
same time
Until the next time the appliance is switched off, it can used as normal.
12
Operating the appliance
Using the timer
Two functions are possible:
Function
Safety cut-out
Countdown timer
3
Pre-condition
Outcome after time
has elapsed
When a heat setting is set
Acoustic signal
0 lights up
Cooking zone switches
off
When cooking zone is not
Acoustic signal
used
0 lights up
If a heat setting and a countdown timer are set simultaneously, the countdown
timer becomes a safety cut-out. The cooking zone is switched off after the time
set has elapsed.
Operating the appliance
Setting the time
Step
Control panel
1.
Touch
2.
Touch or
The pilot light illuminates.
The time is set.
The time counts down.
Display
Pilot light flashes
01 to 99 minutes
Switching timer function off
Step
Control panel
Display
1.
Touch
Pilot light flashes
2.
Touch
The remaining time counts down to 0.
The pilot light goes out.
The timer function is switched off.
Changing the time
Step
Control panel
1.
Touch
2.
Touch or
The pilot light illuminates.
The time is set.
The time counts down.
Display
Pilot light flashes
01 to 99 minutes
Switching off the acoustic signal
Step
Control panel field
1.
Touch
Acoustic signal stops.
Acoustic signal
Acoustic signal to acknowledge.
13
14
Operating the appliance
Automatic switch off
• If a temperature is not set within approx. 10 seconds of the appliance being
switched on, the appliance automatically switches itself off.
• If both grill zones are switched off, the Teppan Yaki automatically switches itself off after approx. 10 seconds.
• If one of the grill zones is not switched off after 90 minutes or if the temperature is not modified, the grill zone automatically switches itself off. is displayed. Before being used again, this grill zone must be set to 0.
Tips for cooking with the Teppan Yaki
15
Tips for cooking with the Teppan Yaki
Using fats and oils
When fats and oils are used, the correct temperature is extremely important.
With the correct temperature setting, the valuable components of the oils and
fats are retained for a long time. When the temperature is too high, the fat begins to smoke (so-called “smoking point”)
Fats / Oils
Max. temperature (°C)
Smoking point (°C)
130
150
Pork fat
170
200
Beef fat
180
210
Olive oil
180
200
Sunflower oil
200
220
Groundnut oil
200
235
Coconut oil
200
240
Butter
3
Note: Always pre-heat the economy grill!
Table
Food to be cooked
Fish and shellfish
Temperature (°C)
140–160
Time / Tips
Pre-heat the economy grill
Salmon fillets
160
8 minutes, turn after
4 minutes
King prawns (without shell)
140
6 minutes, turn after
3 minutes
Shark steaks, approx. 2.5 cm thick
160
10 minutes, turn after
5 minutes
Sole, Müllerin Art (fried in butter)
140
8 minutes, turn after
4 minutes, light side first
Plaice filets
140
6 minutes, turn after
3 minutes
16
Tips for cooking with the Teppan Yaki
Food to be cooked
Veal
Temperature (°C)
140–180
Time / Tips
Pre-heat the economy grill
Veal chop
180
10 minutes, turn after
5 minutes
Medallions of Veal, 4 cm thick
160
10 minutes, turn after
5 minutes
Veal steaks, 3 - 4 cm thick
160
6 minutes, turn after
3 minutes
Veal escalope, natural
180
5 minutes, turn after
2½ minutes
Veal fricasee in cream sauce
180
6 minutes, turn after
3 minutes (the meat strips
should not e stuck to each other)
Beef
160–180
Beef steak
blau, very rare
180
blutig, rare
180
rosa, medium
180
durch, well done
180
Hamburger
160
160
Châteaubriand
100
Pork
160–180
Pre-heat the economy grill
2 minutes, turn after 1 minute
8 minutes, turn after
2 minutes
6 minutes, turn after
3 minutes
8 minutes, turn after
4 minutes
without fatty substances, the
roasting time increases
by approximately 20 %
6 - 8 minutes, turn after
3 - 4 minutes
Sauté the meat in oil on all sides
(turn only when the meat does
not stick to the pan)
Finish off on one side for
10 minutes
Pre-heat the economy grill
Medallions of pork
160
8 minutes, turn after
4 minutes (depending on the
thickness)
Pork steaks
180
8 minutes, turn after 4 minutes
Pork escalope
160
6 minutes, turn after 3 minutes
Spare ribs
160
8 - 10 minutes, turn several
times
Pork skewer
160
6 – 8 minutes, sauté well on all
sides
Tips for cooking with the Teppan Yaki
Food to be cooked
Lamb
160–180
Time / Tips
Pre-heat the economy grill
Lamb chops
180
10 minutes, turn after 5 minutes
Filet of lamb
160
10 minutes, turn after 5 minutes
(important here is that the filets
are fried on all sides)
Lamb steaks
160
6 - 8 minutes, turn after
3 - 4 minutes
Poultry
3
Temperature (°C)
17
140–160
Pre-heat the economy grill
Chicken supreme
140
8 - 10 minutes, turn after
4 - 5 minutes
Turkey breast strips
160
6 minutes, turn several times
Sausages
160
Pre-heat the economy grill
Fried egg
140
Pre-heat the economy grill
Crepes / Omelettes
140-160
Pre-heat the economy grill
Fruits
140-160
Pre-heat the economy grill
Vegetables
140-160
10 – 20 minutes, turn several
times
Vegetables
140-160
10 - 15 minutes, under a cooking lid (turn half way through)
Cook the pre-cooked rice
140-160
10 – 15 minutes, turn several
times
Cook the pre-cooked noodles
140-160
15 - 20 minutes, turn half way
through
Information about acrylamides
According to the latest scientific research, intensive browning of food, especially
in products containing starch, may present a health risk due to acrylamide.
Therefore we recommend cooking at low temperatures and not browning foods
too much.
18
Cleaning and care
Cleaning and care
1
1
Important: There is a risk of being burned when cleaning the hot economy grill!
Important: Never clean the grill surface using abraisive powders or aggressive
detergents!
Cleaning the economy grill using ice cubes
3
1. Turn the appliance off and allow to cool to approx 80 °C.
2. Place the ice cubes onto the grill one after another. At the same time, loosen the
roasting leftovers using a spatula and push them into the trough until all leftovers have been removed. Remove the leftovers from the trough (e.g. using kitchen paper). Cold water can also be used instead of ice cubes.
3. Allow the grill surface to cool to approx 80 °C. Thoroughly clean with a clean
cloth and a little cold water.
4. Cleaning when in a cold condition:
– allow a suitable fat solvent to react for 5 minutes
– remove the cooking residues using a spatula or Inox steel knawl
– Carry out the subsequent cleaning with water (wet cloth).
5. When the grill is cold, remove any stains that may have been caused by proteins
or acids in the foodstuffs using some lemon juice and a clean cloth. Then thoroughly clean using a damp cloth.
If the economy grill has already cooled down before cleaning, heat up to approx.
80° C and switch back off.
Cleaning the economy grill between two dishes
Analogue to point 2-3 above
Cleaning the operating panel
1. Wipe the appliance with a damp cloth and a little washing up liquid.
2. Dry the appliance using a clean cloth.
Removable Frontline strip
The aluminium Frontline strip fastens on by means of magnets. It is easy to remove by hand and can be cleaned with detergent. Please do not use any scouring agents or sponges that scratch. Do not clean the strip in the dishwasher.
What to do if …
19
What to do if …
Problem
The Teppan Yaki cannot be
switched on or is not operating
The residual heat indicator is
not displaying anything.
and number are displayed
1
3
Possible cause
Remedy
More than 10 seconds have
Switch the appliance on again.
passed since the appliance was
switched on
The child safety device is
switched on
Deactivate child safety device
(See the section “Child safety
device”)
Several sensor fields were
touched at the same time
Only touch one sensor field
Automatic switch-off has
been triggered
Remove any objects (pan,
cloths, etc.) that are lying on
the control panel. Switch appliance on again
The cooking zone was only on
If the cooking zone is supfor a short time and is not yet
posed to be hot, contact your
hot
local service centre.
Electronics fault
Disconnect the appliance from
the electrical supply for a few
minutes (Take the fuse out of
the house’s wiring system)
If after switching on again,
is displayed again, call the customer service department
If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre.
Warning! Repairs to the appliance are only to be carried out by qualified service
engineers. Considerable danger to the user may result from improper repairs.
If the appliance has been operated incorrectly, the engineer's visit will be
chargeable, even during the warranty period.
20
Disposal
Disposal
2
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste
disposal facilities.
Old appliance
W
The symbol
on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you
purchased the product.
Installation Instructions
21
Installation Instructions
1
z
z
Safety instructions
Warning! This must be read!
The laws, ordinances, directives and standards in force in the country of use are
to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)
Installation may only be carried out by a qualified electrician.
The minimum distances to other appliances and units are to be observed.
Anti-shock protection must be provided by the installation, for example drawers
may only be installed with a protective floor directly underneath the appliance.
The cut surfaces of the worktop are to be protected against moisture using a
suitable sealant.
The sealant seals the appliance to the work top with no gap.
When building in, protect the underside of the appliance from steam and moisture, e.g. from a dishwasher or oven.
Avoid installing the appliance next to doors and under windows. Otherwise hot
cookware may be knocked off the rings when doors and windows are opened.
Distance from the wall: at least 50 mm.
Risk of injury from electrical current.
• The appliance must be disconnected from the power supply when installing
and uninstalling.
• Follow the electrical schematic.
• Observe all electrical safety rules.
• Ensure anti-shock protection through correct installation by a qualified installer.
• The appliance must be connected to the electrical supply by a qualified electrician.
Loose and incorrect plug and socket connections can cause the terminal
to overheat.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or two-phase connection, the appropriate mains
cable of type H05BB-F Tmax 90°C (or higher) must be used.
A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening
width of at least 3 mm
Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors.
22
Assembly
Assembly
Assembly
3
23
Note! The grill extends 3mm beyond the glass control panel so the panel does
not become hot.
24
Assembly
Assembly
25
26
Installing more than one Frontline hob
Installing more than one Frontline hob
3
Additional parts: cross bar(s), heat resistant silicon, rubber block, shaving blade.
Only use special heat-resistant silicon.
Cut-out section
Distance from the wall: at least 50 mm
Depth:490 mm
Width: The widths of all appliances to be built-in are added together, minus
20 mm (see also “Overview of all appliance widths”)
Example:
Installing more than one appliance
1. Work out the size of the cut-out section and saw it out.
2. Remove Frontline strip from the appliances by hand (magnetic fastening).
3. Lay the appliances one at a time on something soft (for example a blanket) with
the underside facing upwards.
4. Screw / clip fixing plates / retaining grips into the appropriate holes in the protective boxes.
Installing more than one Frontline hob
27
5. Place first appliance in the cut-out. Lay connecting cross bar in the cut-out and
push up halfway against the appliance.
6. Put silicon on the appliance corners that will touch one another. Put silicon on
the end of the cross bar.
7. Loosely screw in fixing plates / retaining grips from below on the worktop and
on the connecting cross bar.
28
Installing more than one Frontline hob
8. Place Frontline strips on the appliances. Check that the Frontline strips are in line
with one another.
9.
10.
11.
12.
Tighten the fixing plate / retaining grip screws.
Inject a line of silicon into the gap between the appliances.
Dampen silicon line with a little soapy water.
Press rubber block hard against the glass ceramic and draw it slowly along the
gap.
13.
14.
15.
16.
Leave silicon until the next day to harden.
Carefully remove projecting silicon with a shaving blade.
Clean glass ceramic thoroughly.
Replace Frontline strips.
Installing more than one Frontline hob
Overview of all appliance widths
180 mm
Worktop-mounted cooker hood
360 mm
Glass ceramic cooking surface with 2 radiation cooking zones
Glass ceramic cooking surface with 2 induction cooking zones
Gas hob with 2 burners
Grill
Grill/Deep fat fryer
Wok
Induction Teppanyaki
580 mm
Glass ceramic cooking surface with 4 radiation cooking zones
Gas hob with 4 burners
Induction Teppanyaki
720 mm
Glass ceramic cooking surface with 4 radiation cooking zones
Glass ceramic cooking surface with 4 induction cooking zones
Gas hob with 4 burners
29
30
Rating Plate
941 177 678
AEG - ELECTROLUX
5,6 kW
220-240 V
50/60
Induction 5,6 kW
59TPA23KO
FM6800TYAN
Guarantee/Customer Service
31
Guarantee/Customer Service
Standard guarantee conditions
We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part thereof is proved to be defective
by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
• The appliance has been correctly installed and used only on the electricity
supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us.
• Electrolux Service Force Centre must undertake all service work under this
guarantee
• Any appliance or defective part replaced shall become the Company’s property.
• This guarantee is in addition to your statutory and other legal rights.
Exclusions
• Damage or calls resulting from transportation, improper use or neglect, the
replacement of any light bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed
or calls to appliances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those
which are subject to rental agreements.
• Products of Electrolux manufacturer that are not marketed by Electrolux
32
Guarantee/Customer Service
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for
the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications:
• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced
by production of a valid purchase document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in
your new country of residence for this particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred
to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used
within the home, i.e. is not used for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in force within your new country of
residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
Guarantee/Customer Service
33
www.electrolux.com
p
t
b
Albania
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/
Belgien
+32 2 363 04 44
Bergensesteenweg 719, 1502 Lembeek
Èeská republika
+420 2 61 12 61 12
Budìjovická 3, Praha 4, 140 21
Danmark
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
Deutschland
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
Eesti
+37 2 66 50 030
Mustamäe tee 24, 10621 Tallinn
España
+34 902 11 63 88
Carretera M-300, Km. 29,900
Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire
LU4 9QQ
Hellas
+30 23 10 56 19 70
4 Limnou Str., 54627 Thessaloniki
Hrvatska
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
Ireland
+353 1 40 90 753
Long Mile Road Dublin 12
Italia
+39 (0) 434 558500
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija
+37 17 84 59 34
Kr. Barona iela 130/2, LV-1012, Riga
Lithuania
+3702780607
Žirmūnų 67, LT-09001 Vilnius
Luxembourg
+352 42 431 301
Rue de Bitbourg, 7, L-1273 Hamm
Magyarország
+36 1 252 1773
H-1142 Budapest XIV,
Erzsébet királyné útja 87
Nederland
+31 17 24 68 300
Vennootsweg 1, 2404 CG Alphen aan den Rijn
Norge
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
Österreich
+43 18 66 400
Herziggasse 9, 1230 Wien
Polska
+48 22 43 47 300
ul. Kolejowa 5/7, Warszawa
Portugal
+35 12 14 40 39 39
Quinta da Fonte - Edificio Gonçalves Zarco
- Q 35
2774 - 518 Paço de Arcos
Romania
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671 RO
Schweiz/Suisse/
Svizzera
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
Slovenija
+38 61 24 25 731
Electrolux Ljubljana d.o.o.
Gerbièeva 98, 1000 Ljubljana
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux
Domáce spotrebièe SK, Seberíniho 1, 821
03 Bratislava
Suomi
www.electrolux.fi
Sverige
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143,
S-105 45 Stockholm
34
Guarantee/Customer Service
p
t
b
Türkiye
+90 21 22 93 10 25
Tarlabaþý caddesi no : 35 Taksim
Istanbul
Ðîññèÿ
+7 495 937 7837
129090 Ìîñêâà, Îëèìïèéñêèé ïðîñïåêò, 16,
ÁÖ „Îëèìïèê“
Óêðà¿íà
+380 44 586 20 60
04074 Êè¿â, âóë.Àâòîçàâîäñüêà,
2a, ÁÖ „Àëêîí“
Service and Spare Parts
35
Service and Spare Parts
If the event of your appliance requiring service, or if you wish to purchase spare
parts, please contact Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about
Service Force, please visit the website at
www. serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the
heading „What to do if...“
When you contact the Service Force Centre you will need to give the following
details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date.
Please note that a valid purchase receipt or
guarantee documentation is required for inguarantee service calls.
Customer Care
For general enquiries concerning your AEG
appliance, or for further information on
AEG products please contact our Customer
Care Department by letter or telephone at
the address below or visit our website at
www.aeg.co.uk.
Customer Care Department
For Customer Service in the Republic of
Major Appliances
Ireland please contact us at the address beAEG Domestic Appliances
low:
Addington Way
AEG/ Electrolux Group (Ire) Ltd
Luton
Long Mile Road/ Dublin 12
Bedfordshire, LU4 9QQ
Republic of Ireland
Tel: 08705 350350 (*)
Tel: +353 (0) 1 4090754
Email: service.eid@electrolux.ie
(*) Calls may be recorded for training purposes
374 486 813 -O-160508-02
Subject to change without notice
www.electrolux.com
www.aeg-electrolux.co.uk
Download PDF

advertising