Crosslee | CL427WV-031242715002 | User manual | Crosslee CL447SV-031244715300 User Manual

Crosslee CL447SV-031244715300 User Manual
cl 59323 printers spreads
11/12/02
11:47 AM
Page 1
OPERATION
INSTALLATION
TUMBLE DRYER VENTING
When using a vent hose, remember the following points:
Your tumble dryer will release warm, damp air in one of these
three ways:
–
The vent hose must be at least 10cm (4 ins) in diameter.
–
No more than three right-angled bends should be allowed
when positioning the vent hose.
–
The vent hose must not be shared with other appliances, for
example, a cooker hood outlet.
–
When drying, the vent hose must always be extended to an
open door or window.
FINAL INSTALLATION
(1) Front Venting. Venting
through a grille on the plinth.
A kit is available to convert to
rear venting.
(2) Fixed Rear Venting. Venting
through a hole at the bottom of
the back panel. A vent hose is
available
to
convert
to
extendible rear venting.
(3) Extendible Rear Venting.
This contains a retractable vent
hose.
Place the filter in its operating
position as shown in the diagram.
If you wish to change the side on
which your door opens, see the
instructions on the back page.
;;;;;;
;;;;
;;;;;;
;;;;
;;;;;;
;;;;;;;;;;
;;;;;;
;;;;;;;;;;
;;;;;;
;;;;;;;;;;
;;;;;;
;;;;;;;;;;
Remove any dust by wiping the drum
and door with a damp cloth. Any initial
smell from the heater should
disappear after the first period of
heating.
Position the tumble dryer so that the
plug remains accessible after
installation.
The best solution is to make a permanent connection through
either a wall or a window. This is particularly recommended for
small, cool rooms and a kit for this purpose is available as an
accessory. However, venting arrangement (1) requires that it be
converted to rear venting before a permanent connection can be
made.
THE CONTROLS
Grip middle piece of filter with fingers.
Face the brush bar at the bottom
edge of the filter to the front.
Slide the filter into the space below
the door in a right angle position.
Load clothes loosely into the drum.
Load sheets first, starting with one corner.
Close the door.
B
A
Dry your hands.
Check that the timer is in the ‘0’ position.
To lengthen or shorten a timed programme, reset the timer knob.
Plug in the machine.
Select correct heat position (see programme chart on control
panel for recommendations).
Set the timer to the required time setting (see programme chart
on control panel for recommendations).
Should the clothes become dry before the cycle has finished, or if
an excessive programme time has been selected, the drum will
continue to rotate while the thermostat will automatically switch
the heater off to prevent over-drying and save energy.
Remove any threads or fluff by
hand or with a soft brush.
–
Slide the filter back
–
Wash the filter occasionally in
detergent solution and with a
soft brush to remove small
particles.
OPTIONAL EXTRAS
If the clothes are not dry after normal drying time:
Front to Extendible Rear Venting Kit
–
Check that you used the correct heater setting.
To convert your dryer from front venting to extendible rear venting.
–
Check that you have not set the timer within a cool
down period.
Vent Hose
Suitable for tumble drying
–
Check that the lint filter has been cleaned. A blocked
filter will restrict the airflow.
–
Check that your dryer is heating - below the door to the
right side, should feel warm to the touch after the first
10-15 minutes of its programme. Failure to heat may
indicate the safety cut-out has operated. To reset,
simply press the red button at the rear of the machine.
If it has operated, a sharp “click” will be heard. This cutout only operates if the airflow is severely restricted so
make sure the filter is clean, the air inlets and outlets at
the front and back are not blocked, and that all other
restrictions are removed before re-starting.
Roll dripping wet articles in a towel to remove excess water.
If the cut-out continues to operate after checking the
above points, you should contact your service agent.
It is better to dry small and large articles together.
Do not place items contaminated with inflammable substances
in the dryer, such as petrol, cleaning solvents, cooking oil, fat, or
hair lacquer. These can cause fires. For the same reason, do not
dry rubber, foam rubber, plastic or paper.
Only available for fixed rear dryers. Leads the warm, damp air to
an open door or window.
Wall/Window Vent Kit
To make a permanent connection through a wall or window. Front
venting dryers need converting to rear venting before installing this
kit (see ‘Front to Extendible Rear Venting Kit’ above).
Stacking Kit
To enable your dryer to be secured onto the top of a front loading
washing machine (to save floor space).
The above items can be purchased as accessories for your tumble
dryer from your supplier.
TECHNICAL DATA
OVERALL DIMENSIONS:
Height: 85 cm
We suggest a fabric conditioner to be used to reduce static
electricity.
Do not overload the dryer or dry large bulky items such as
duvets or sleeping bags as it is important that the airflow through
the dryer is not obstructed.
A B
–
ANY PROBLEMS
To avoid the need to iron easycare polyester/cotton items it is
better to only dry small loads (i.e half fill drum).
B
Pull the filter upwards and away
from the appliance.
ADDITIONAL INFORMATION
Place delicate articles e.g. tights, scarves, inside a pillowcase.
A
–
There is an automatic 12 minute cool down period at the end of
every cycle, during which the heater is switched off. This helps to
minimise creasing.
Do not tumble dry woollen or wool mixture articles unless the
article is labelled to be suitable due to a possibility of shrinkage.
A
ALWAYS CLEAN THE FILTER. Failure to clean the filter will
extend drying times and could cause the safety cut-out to
operate. There are two types of filter your dryer main contain.
CARE LABELS YOU MAY FIND ON YOUR
FABRICS
Do not tumble dry
B
AFTER REMOVING THE DRIED CLOTHES:
The drum will begin rotating. Reversing drum models will stop
every few minutes to rotate in the reverse direction for a short
time.
Tumble dry using half heat
Select the required
heat setting based
on the
recommendations
on the control
panel.
When drying large items such as sheets, we suggest you
periodically stop the dryer to redistribute the load.
Check care labels inside the garments.
Tumble dry using full heat
B. HEAT SWITCH(ES)
NEVER SWITCH THE DRYER OFF AND LEAVE A
HOT LOAD IN THE DRUM.
To stop the machine during the middle of the programme simply
open the door; the drum will stop rotating automatically and
restart when you close the door.
PREPARATION
A. THE TIMER
Select the required
drying time based
on the
recommendations
on the control
panel.
FITTING OF FILTER
Open the door.
If your machine does not work check the following before
calling a service engineer:
–
Check that there is a supply of electricity.
–
Check that the door has been properly closed and the
machine is switched on.
–
Check the plug internal connections.
Width: 59.5 cm
Depth: 53 cm
MAXIMUM DRY WEIGHT LOADS:
Cotton 6kg
(for minimum creasing 2kg)
Delicates 2kg
For electrical ratings see plate on back of dryer.
For Model No. see serial plate inside door (needed when requesting service).
Room temperature range 5˚C to 30˚C.
Your washing machine should have a spin speed of not less than 800rpm.
cl 59323 printers spreads
11/12/02
11:47 AM
Page 1
OPERATION
INSTALLATION
TUMBLE DRYER VENTING
When using a vent hose, remember the following points:
Your tumble dryer will release warm, damp air in one of these
three ways:
–
The vent hose must be at least 10cm (4 ins) in diameter.
–
No more than three right-angled bends should be allowed
when positioning the vent hose.
–
The vent hose must not be shared with other appliances, for
example, a cooker hood outlet.
–
When drying, the vent hose must always be extended to an
open door or window.
FINAL INSTALLATION
(1) Front Venting. Venting
through a grille on the plinth.
A kit is available to convert to
rear venting.
(2) Fixed Rear Venting. Venting
through a hole at the bottom of
the back panel. A vent hose is
available
to
convert
to
extendible rear venting.
(3) Extendible Rear Venting.
This contains a retractable vent
hose.
Place the filter in its operating
position as shown in the diagram.
If you wish to change the side on
which your door opens, see the
instructions on the back page.
;;;;;;
;;;;
;;;;;;
;;;;
;;;;;;
;;;;;;;;;;
;;;;;;
;;;;;;;;;;
;;;;;;
;;;;;;;;;;
;;;;;;
;;;;;;;;;;
Remove any dust by wiping the drum
and door with a damp cloth. Any initial
smell from the heater should
disappear after the first period of
heating.
Position the tumble dryer so that the
plug remains accessible after
installation.
The best solution is to make a permanent connection through
either a wall or a window. This is particularly recommended for
small, cool rooms and a kit for this purpose is available as an
accessory. However, venting arrangement (1) requires that it be
converted to rear venting before a permanent connection can be
made.
THE CONTROLS
Grip middle piece of filter with fingers.
Face the brush bar at the bottom
edge of the filter to the front.
Slide the filter into the space below
the door in a right angle position.
Load clothes loosely into the drum.
Load sheets first, starting with one corner.
Close the door.
B
A
Dry your hands.
Check that the timer is in the ‘0’ position.
To lengthen or shorten a timed programme, reset the timer knob.
Plug in the machine.
Select correct heat position (see programme chart on control
panel for recommendations).
Set the timer to the required time setting (see programme chart
on control panel for recommendations).
Should the clothes become dry before the cycle has finished, or if
an excessive programme time has been selected, the drum will
continue to rotate while the thermostat will automatically switch
the heater off to prevent over-drying and save energy.
Remove any threads or fluff by
hand or with a soft brush.
–
Slide the filter back
–
Wash the filter occasionally in
detergent solution and with a
soft brush to remove small
particles.
OPTIONAL EXTRAS
If the clothes are not dry after normal drying time:
Front to Extendible Rear Venting Kit
–
Check that you used the correct heater setting.
To convert your dryer from front venting to extendible rear venting.
–
Check that you have not set the timer within a cool
down period.
Vent Hose
Suitable for tumble drying
–
Check that the lint filter has been cleaned. A blocked
filter will restrict the airflow.
–
Check that your dryer is heating - below the door to the
right side, should feel warm to the touch after the first
10-15 minutes of its programme. Failure to heat may
indicate the safety cut-out has operated. To reset,
simply press the red button at the rear of the machine.
If it has operated, a sharp “click” will be heard. This cutout only operates if the airflow is severely restricted so
make sure the filter is clean, the air inlets and outlets at
the front and back are not blocked, and that all other
restrictions are removed before re-starting.
Roll dripping wet articles in a towel to remove excess water.
If the cut-out continues to operate after checking the
above points, you should contact your service agent.
It is better to dry small and large articles together.
Do not place items contaminated with inflammable substances
in the dryer, such as petrol, cleaning solvents, cooking oil, fat, or
hair lacquer. These can cause fires. For the same reason, do not
dry rubber, foam rubber, plastic or paper.
Only available for fixed rear dryers. Leads the warm, damp air to
an open door or window.
Wall/Window Vent Kit
To make a permanent connection through a wall or window. Front
venting dryers need converting to rear venting before installing this
kit (see ‘Front to Extendible Rear Venting Kit’ above).
Stacking Kit
To enable your dryer to be secured onto the top of a front loading
washing machine (to save floor space).
The above items can be purchased as accessories for your tumble
dryer from your supplier.
TECHNICAL DATA
OVERALL DIMENSIONS:
Height: 85 cm
We suggest a fabric conditioner to be used to reduce static
electricity.
Do not overload the dryer or dry large bulky items such as
duvets or sleeping bags as it is important that the airflow through
the dryer is not obstructed.
A B
–
ANY PROBLEMS
To avoid the need to iron easycare polyester/cotton items it is
better to only dry small loads (i.e half fill drum).
B
Pull the filter upwards and away
from the appliance.
ADDITIONAL INFORMATION
Place delicate articles e.g. tights, scarves, inside a pillowcase.
A
–
There is an automatic 12 minute cool down period at the end of
every cycle, during which the heater is switched off. This helps to
minimise creasing.
Do not tumble dry woollen or wool mixture articles unless the
article is labelled to be suitable due to a possibility of shrinkage.
A
ALWAYS CLEAN THE FILTER. Failure to clean the filter will
extend drying times and could cause the safety cut-out to
operate. There are two types of filter your dryer main contain.
CARE LABELS YOU MAY FIND ON YOUR
FABRICS
Do not tumble dry
B
AFTER REMOVING THE DRIED CLOTHES:
The drum will begin rotating. Reversing drum models will stop
every few minutes to rotate in the reverse direction for a short
time.
Tumble dry using half heat
Select the required
heat setting based
on the
recommendations
on the control
panel.
When drying large items such as sheets, we suggest you
periodically stop the dryer to redistribute the load.
Check care labels inside the garments.
Tumble dry using full heat
B. HEAT SWITCH(ES)
NEVER SWITCH THE DRYER OFF AND LEAVE A
HOT LOAD IN THE DRUM.
To stop the machine during the middle of the programme simply
open the door; the drum will stop rotating automatically and
restart when you close the door.
PREPARATION
A. THE TIMER
Select the required
drying time based
on the
recommendations
on the control
panel.
FITTING OF FILTER
Open the door.
If your machine does not work check the following before
calling a service engineer:
–
Check that there is a supply of electricity.
–
Check that the door has been properly closed and the
machine is switched on.
–
Check the plug internal connections.
Width: 59.5 cm
Depth: 53 cm
MAXIMUM DRY WEIGHT LOADS:
Cotton 6kg
(for minimum creasing 2kg)
Delicates 2kg
For electrical ratings see plate on back of dryer.
For Model No. see serial plate inside door (needed when requesting service).
Room temperature range 5˚C to 30˚C.
Your washing machine should have a spin speed of not less than 800rpm.
cl 59323 printers spreads
11/12/02
11:47 AM
Page 2
IMPORTANT USER INFORMATION
These notes are provided in the interest of safety.
You must read them before installing or using the appliance.
DO NOT allow children to tamper with the controls and keep
them away from the dryer when it is in operation.
–
DO NOT place articles in the dryer if anything other than a
water solution has been used in the cleaning process.
–
DO NOT attempt to dry dripping wet articles or items
containing foam rubber or rubber-like materials.
–
DO NOT use the tumble dryer if you suspect that it is
damaged in any way. Under no circumstances should you
attempt to repair the appliance yourself. Repairs carried out
by inexperienced persons may cause serious injury. Consult
your local appointed service engineer and insist on genuine
spare parts.
THIS APPLIANCE MUST BE
EARTHED
Dryers fitted with hinge cover:-
Open the door. Undo screw (A)
remove switch strike (B) and replace
screw. Remove screws (C) and latch
plate (D). Remove hinge block screws
(E). Remove door from hinge blocks.
Remove hinge screws
(F) and hinge (G) and
refit to opposite side as
shown.
Dryers fitted without hinge cover:-
Your dryer is supplied with a reversible door. To change the direction of opening proceed as follows for your type of door.
REVERSING THE DOOR OPENING
INSTRUCTIONS FOR USE
–
–
Pull the hinge cover (F)
forwards to remove it.
Remove two outer screws
(G). Remove door. Fit latch
plate (D) with screws (C).
–
DO NOT exceed the recommended maximum load.
Open the door. Undo screw
(A) remove switch strike (B)
and replace screw. Remove
screws (C) and latch plate
(D). Remove hinge cover
screw (E). Close the door.
–
–
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS APPLIANCE.
KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.
–
DO NOT allow fluff to accumulate around the tumble dryer.
GB
–
–
Refit latch plate (D) with screws (C). Remove screw (H) at top of
door and refit switch strike (B) as shown. Fit door to hinge blocks
and secure with screws (E).
–
DO NOT block the air inlets at the front and back of your
dryer.
Fit screw (E) to secure hinge
cover. Remove screw (H) at
top of door and refit switch
strike (B) as shown.
–
–
Reverse door and fit to dryer
in closed position. Refit
screws (G) and hinge cover
(F). Open the door.
–
DO NOT use a two-way adaptor, or extension lead. The dryer
must be connected to its own socket.
4213 094 59323
–
–
FPL ‘98
–
This tumble dryer is intended for NORMAL DOMESTIC USE
ONLY.
Please note it is not recommended that the dryer be placed
directly next to ovens or cookers, as the performance of the
dryer may be affected.
Do not stack the tumble dryer on top of other appliances
without the correct stacking kit.
Any electrical work required to install the appliance should
be carried out by a qualified person.
It is important to clean the lint filter after each drying cycle or
the restrictions to airflow will extend drying times and could
cause the safety cut-out to trip.
Under no circumstances should anything other than the
recommended articles be placed in the tumble dryer.
The tumble dryer should be serviced by an appointed
service organisation and only genuine parts used.
It is dangerous to alter or modify the product in any way other
than fitting authorised accessories.
We recommend that the appliance is unplugged each time
after use. It should always be disconnected from the
electricity supply if it is to be left unattended for long periods
(i.e. weekends, holidays etc.)
The rear of the dryer gets quite hot during use, position the
dryer so that the back is not accessible while in operation,
but the sides have a space available to allow airflow.
It is important to clean fluff from the window of the dryer and
around the door seal after each drying cycle. Failure to do so
could result in water leaking.
LARGE BASIC
–
cl 59323 printers spreads
11/12/02
11:47 AM
Page 2
IMPORTANT USER INFORMATION
These notes are provided in the interest of safety.
You must read them before installing or using the appliance.
DO NOT allow children to tamper with the controls and keep
them away from the dryer when it is in operation.
–
DO NOT place articles in the dryer if anything other than a
water solution has been used in the cleaning process.
–
DO NOT attempt to dry dripping wet articles or items
containing foam rubber or rubber-like materials.
–
DO NOT use the tumble dryer if you suspect that it is
damaged in any way. Under no circumstances should you
attempt to repair the appliance yourself. Repairs carried out
by inexperienced persons may cause serious injury. Consult
your local appointed service engineer and insist on genuine
spare parts.
THIS APPLIANCE MUST BE
EARTHED
Dryers fitted with hinge cover:-
Open the door. Undo screw (A)
remove switch strike (B) and replace
screw. Remove screws (C) and latch
plate (D). Remove hinge block screws
(E). Remove door from hinge blocks.
Remove hinge screws
(F) and hinge (G) and
refit to opposite side as
shown.
Dryers fitted without hinge cover:-
Your dryer is supplied with a reversible door. To change the direction of opening proceed as follows for your type of door.
REVERSING THE DOOR OPENING
INSTRUCTIONS FOR USE
–
–
Pull the hinge cover (F)
forwards to remove it.
Remove two outer screws
(G). Remove door. Fit latch
plate (D) with screws (C).
–
DO NOT exceed the recommended maximum load.
Open the door. Undo screw
(A) remove switch strike (B)
and replace screw. Remove
screws (C) and latch plate
(D). Remove hinge cover
screw (E). Close the door.
–
–
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS APPLIANCE.
KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.
–
DO NOT allow fluff to accumulate around the tumble dryer.
GB
–
–
Refit latch plate (D) with screws (C). Remove screw (H) at top of
door and refit switch strike (B) as shown. Fit door to hinge blocks
and secure with screws (E).
–
DO NOT block the air inlets at the front and back of your
dryer.
Fit screw (E) to secure hinge
cover. Remove screw (H) at
top of door and refit switch
strike (B) as shown.
–
–
Reverse door and fit to dryer
in closed position. Refit
screws (G) and hinge cover
(F). Open the door.
–
DO NOT use a two-way adaptor, or extension lead. The dryer
must be connected to its own socket.
4213 094 59323
–
–
FPL ‘98
–
This tumble dryer is intended for NORMAL DOMESTIC USE
ONLY.
Please note it is not recommended that the dryer be placed
directly next to ovens or cookers, as the performance of the
dryer may be affected.
Do not stack the tumble dryer on top of other appliances
without the correct stacking kit.
Any electrical work required to install the appliance should
be carried out by a qualified person.
It is important to clean the lint filter after each drying cycle or
the restrictions to airflow will extend drying times and could
cause the safety cut-out to trip.
Under no circumstances should anything other than the
recommended articles be placed in the tumble dryer.
The tumble dryer should be serviced by an appointed
service organisation and only genuine parts used.
It is dangerous to alter or modify the product in any way other
than fitting authorised accessories.
We recommend that the appliance is unplugged each time
after use. It should always be disconnected from the
electricity supply if it is to be left unattended for long periods
(i.e. weekends, holidays etc.)
The rear of the dryer gets quite hot during use, position the
dryer so that the back is not accessible while in operation,
but the sides have a space available to allow airflow.
It is important to clean fluff from the window of the dryer and
around the door seal after each drying cycle. Failure to do so
could result in water leaking.
LARGE BASIC
–
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising