Dometic RH302D User Manual

Dometic RH302D User Manual
INSTRUCTION for USE
ABSORPTION-REFRIGERATOR
miniBar
RH 400
RH 400 LR
RH 302 D
RH 402 D
English
Type H20 / 60
821 2693-31
T.D. 01/2003
TABLE OF CONTENTS
1.0
INTRODUCTION
3
2.0
FOR YOUR SAFETY
3
3.0
WARRANTY AND
CUSTOMER SERVICE
3
4.0
INSTALLATION
4
5.0
2.1 Warnings and Safety Advice
2.2 Coolant
4.1
4.2
4.3
4.4
4.5
4.6
4.7
3
3
The Purpose of this Manual
Tools/Materials Required
Unpacking
Cleaning
Installation
Securing
Connecting the Device to the
Electricity Supply
4.8 Changing the Sliding Hinge
4.9 Changing the Doorhang
4.10 Changing the Decor Panel
4
4
4
4
5
6
6
INSTRUCTION FOR USE
10
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
Initial Operation
Temperature Control
Automatic Defrost Function
Leakage Detection
Interior Light
Environmental Advice
Disposal
Energy Saving Tips
Declaration
Check List
Technical Data
Index
2
7
8
9
10
10
10
10
11
12
12
12
12
13
14
15
1.0
INTRODUCTION
You have made an excellent choice by choosing the Dometic miniBar.
We are convinced that you will be satisfied with your new appliance in every
way.
Silent in operation, the miniBar fulfils high quality standards and guarantees
an efficient use of resources and energy during its entire working life, i.e.
during manufacturing, use and disposal.
Please study the installation and operating instructions carefully before
attempting to operate the miniBar.
2.0
2.1
FOR YOUR SAFETY
Warnings and Safety Advice
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
2.2
3.0
In the interests of children's safety:
When disposing of the refrigerator, remove all doors and leave the
shelves inside. This prevents children from being accidentally trapped or
suffocated in the refrigerator.
Never open the cooling unit - it is under high pressure.
Never store explosive substances, such as lighter fuel, petrol, ether or
similar products in the miniBar.
The minibar is not suitable for the proper storage of medications.
The miniBar must be installed in such a way that accidental contact with
the cooling unit (which heats up when in use) is impossible.
The appliance has to be connected to a properly earthed socket in line
with the relevant valid country regulations.
Servicing must only be carried out by authorised service personnel.
Coolant
Ammonia is used as the coolant. This is a natural compound which is also
present in common household cleaners (1 litre of salmiac cleaner contains
up to 200g of ammonia - this is roughly double the amount contained in the
cooling unit).
If a leak occurs (which can be easily detected due to the unpleasant smell):
Ÿ Switch the device off (pull mains plug, if applicable);
Ÿ Ventilate room thoroughly.
Ÿ Inform hotel personnel.
For the safety of hotel guests and personnel, it has been established by
inspectors that the coolant poses no threat to health.
WARRANTY AND CUSTOMER SERVICE
Warranty arrangements are in accordance with EC Directive 44/1999/CE and
the normal conditions applicable for the country concerned.
For warranty or other servicing, please contact our Dometic Service department.
Any damage due to improper use is not covered by the warranty. The warranty
does not cover any modifications to the appliance or the use of non-original
Dometic parts; the warranty does not apply if the installation and operating
instructions are not adhered to and no liability shall be entertained. Parts can be
ordered throughout Europe from our Dometic Service department.
3
When contacting customer service, please always state model, product,
MLC-Code and serial number! You can find this information on the model
label inside the device.
RH 400
e.g.
4.0
4.1
INSTALLATION
The Purpose of this Manual
The manual shows you how to:
Ÿ install the miniBar correctly.
Ÿ operate the miniBar correctly.
Ÿ guarantee the miniBar´s correct maintenance and functioning.
Ÿ deal with faults by yourself.
4.2
Tools / Materials Required
You will need the following tools for initial operation:
mild detergent
4.3
4.4
Unpacking
Check during unpacking that the device is defect-free.
Ÿ Report transport damage to the transport company within 48 hours.
Ÿ Check that the voltage noted on the model label corresponds to the
mains voltage.
The following parts can be found in the miniBar :
Cleaning
Before operating the miniBar, we recommend you clean it both inside and
outside.
Ÿ Use a soft cloth, lukewarm water and a mild detergent.
Ÿ Following this, wash out the miniBar using clean water and dry
thoroughly.
Ÿ At annual intervals, remove dust from fridge aggregate using a brush or
soft cloth.
WARNING:
To prevent material damage:
Ÿ Do not use soap or detergents which are harsh, coarse or
which contain soda.
Ÿ Keep the door seal free from oil and grease.
4
4.5
Installation
IMPORTANT:
Please follow the installation details below
carefully. Guarantee is valid for products
installed as described only.
1. The refrigerator must be level both directions
2. There sould be 20mm clearance to the wall
3. Ventilation must be provided as shown in
alternatives A,B,C or D
4. The ventilation duct must at least measure
105mm x the wtdth of the refrigerator
5. Only the entire cooling unit must project into
the duct as shown
6 Air passing through the duct must not be
preheated by any source of heat
7. Ventilation grills, if used, must have openings
of at least 200cm² each
5
4.6
Securing
The miniBar must be screwed onto the cupboard using the lower hinges.
1. Tighten screw.
4.7
2. Put on cap.
Connecting the Device to the Electricity Supply
Ÿ The device must be connected to a properly earthed socket in line with
the relevant valid country regulations.
Ÿ Check prior to initial operation that the voltage
noted on the model label corresponds to the
mains voltage.
If this is not the case, do not connect the
device and contact your dealer!
6
4.8
Changing the Sliding Hinge
(RH 400 LR, optional with RH 302 D and RH 402 D)
1.
2.
3.
4.
Distance to cupboard door (A)
1.
mm
A
2.
mm
1. When closed, the cupboard door (A)
must not lie against the rest of the
surrounding cupboard area (distance 1-2mm).
2. There must be a distance of 6-8mm
between the cupboard door and the
miniBar.
7
4.9
Changing the Doorhang
1.
L
R
2.
3.
2.
1.
4.
5.
6.
7.
R
L
1.
2.
8.
12.
9.
10.
13.
8
11.
4.10
Changing the Decor Panel (optional with RH 400 LR)
- Unscrew the 2 screws of the upper door hinge.
- Pull the door and the hinge off, away from the housing and in an upward
direction from the lower hinge pin (2-3).
- Unscrew the screws (4) and pull off the frame section (5).
- Pull the decorative panel (6) out of the door frame and push in the new
decorative panel (7) in such a way that the upper edge runs exactly
parallel to the upper section of the frame.
Put on upper section of frame (5) and re-fasten with screws (4).
- Set the door on the lower hinge, put the upper hinge in the door, guide
the door with the hinge into the hinge hole opening and screw together.
9
5.0
5.1
INSTRUCTION FOR USE
Initial Operation
Ÿ The device must be plugged into a properly
earthed socket.
Ÿ The miniBar achieves its operating
temperature after several hours.
The miniBar operates silently !
5.2
Temperature Control
5.3
Automatic Defrost Function
The miniBar is fitted with an electronic temperature control with a fixed
temperature setting.
Ÿ The first defrosting phase commences 39 hours after the initial operation
(5.1) and lasts for two hours.
Ÿ After this, the device operates for 22 hours at a time, followed by a
defrosting period of 2 hours .
T
22h
22h
39h
2h
T
S
2h
T
S
The ice layer must never be removed using
force, nor must the defrosting process ever
be accelerated using a heater.
5.4
Leakage Detection
The electronics carries out a leakage test after
every defrosting period ( every 24 hrs) by
measuring the temperature at the evaporator
by means of a second sensor.
If a leakage is detected, the miniBar is shut off
by the electronics.
Evaporator sensor
10
Air sensor
5.5
Interior Light (only RH 400 LR)
When the door is opened, the light in the cooling shelf is switched on
via a sensor.
Changing bulbs:
1. Pull out the
mains plug.
2. Remove the
reflector disk.
4. Insert new bulb.
3. Remove the
defective bulb.
5.Clip reflector disk back in.
Please contact Dometic Service
centres for replacement light bulbs.
11
5.6
5.7
Enviromental Advice
miniBars manufactured by Dometic are free from CFCs / HCFCs and
fluorinated hydrocarbons.
The cooling unit uses ammonia as the coolant (a natural compound of
hydrogen and nitrogen). Cyclopentane, which does not damage the ozone
layer, is used as propellant for the insulation made from PU-foam.
Disposal
In order to ensure the re-use of recyclable packaging materials, these must
be disposed of using local collection systems. The device itself must be
handed over to a disposal company or local council which will guarantee
the correct use of recyclable materials and the proper disposal of the rest.
5.8
Energy Saving Tips
Ÿ
At an average room temperature of approx. 22°C, it is sufficient to
operate the miniBar with an average thermostat setting.
Ÿ
Ÿ
If possible, always store pre-cooled goods.
Do not expose the miniBar to direct sunlight and do not place it close
to a source of heat.
An unobstructed air circulation in the fridge aggregate must be
ensured.
When removing goods, only open the miniBar briefly.
Switch on the miniBar approx. 12 hours prior to stocking.
Ÿ
Ÿ
Ÿ
5.9
Declaration of conformity
12
5.10
Check List
Failure : No cooling (the aggregate at the back of the device is cold).
Possible Cause
Self Help
a.) The device plug is not
plugged in.
a.) Plug in device plug.
b.) No voltage in socket.
b.) Check building fuse.
Authorised Service
c.) Defective electronics or
sensor feelers.
c.) Install new
electronics or sensor.
d.) Defective heating cartridge.
d.) Install new heating
cartridge.
e.) The device is in its defrosting
phase.
e.) See operating instruction
5.3
Failure : No cooling (the aggregate is warm).
Possible Cause
Self Help
a.) The device is not levelled.
a.) Level the device using a
spirit level.
b.) The device was only
switched on a short while ago.
b.) Switch on the device and
let it run for 5-6 hours.
c.) Defective cooling aggregate.
Authorised Service
c.) Check whether
repair is feasible. If not,
exchange device.
Failure : Poor Cooling Performance.
Possible Cause
Self Help
a.) The cooling aggregate is not
sufficiently ventilated.
a.) Check that the ventilation
grids are not covered. Check
that device has been installed
properly (installation instruction
4.5).
b.) The device is exposed to
direct sunlight.
b.) Follow installation
instruction 4.5.
c.) The fridge door does not
close tightly.
c.) Check installation in line
4.5.
d.) Light permanently on when
door closed.
e.) The fridge was stocked a
short while ago.
e.) Check fridge after 5-6
hours for proper cooling
function.
Authorised Service
c.) Is door magnet
there? Install new door,
if required.
d.) Replace lighting
sensor. Install new door,
if required.
Failure : Frost formation in fridge.
Possible Cause
Self Help
Authorised Service
a.) The fridge door does not
close tightly.
a.) Check installation is in line
with 4.5.
a.) Is door magnet
there?
Install new door.
13
5.11
Technical Data
Model
RH 400
RH 400 LR
Freestanding /
Freestanding /
Built-in
Built-in
Metal
Metal
(litres)
40
40
cooled / uncooled
40 / -
40 / -
554x401x446
554x401x446
Casing
Gross Contentss
Dimensions (mm)
(H x W xD)
Electrical Rating (W) 65
65
Power Consumption
kWh / 24h*
0,8
0,8
Net Weight (kg)
14
14
RH 302 D
RH 402 D
Freestanding /
Freestanding /
Built-in
Built-in
Metal
Metal
(litres)
30
40
cooled / uncooled
30 / -
40 / -
522x384x411
554x401x446
Model
Casing
Gross Contentss
Dimensions (mm)
(H x W xD)
Electrical Rating (W) 65
65
Power Consumption
kWh / 24h*
0,7
0,8
Net Weight (kg)
11
14
* Power consumption measured at an average ambient temperature of 25°C as an average
annual value and at a cooling compartment temperature of 7°C in line with DIN/EN153.
We reserve the right to make technical modifications to our products without notice!
14
5.12
Index
Cleaning............................................ 4
Check List..........................................13
Customers Service............................ 3
Coolant..............................................3,12
Data Plate..........................................3
Decor Panel...................................... 9
Defrosting..........................................10
Disposal.............................................5
Doorhang...........................................8
Electricity Supply............................... 6
Energy Saving Tips........................... 12
Failures..............................................13
Initial Operation................................. 10
Installation......................................... 5
Interior Light...................................... 11
Safety Advice.....................................3
Securing............................................ 6
Sliding Hinge..................................... 7
Spare Parts....................................... 3
Temperature Control..........................7
Unpacking..........................................4
Ventilation..........................................5,13
Warranty.............................................8
15
Dometic GmbH
In der Steinwiese 16
D-57074 Siegen
Phone: +49-(0) 271 / 692 0
Fax: +49-(0) 271 / 692 300
www.dometic.de/minibar
© Dometic GmbH - 2002 - Subject to change without notice - Printed in Germany
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement