Dometic HIPRO 3000 User Manual

Dometic HIPRO 3000 User Manual
INSTRUCTIONS for USE
INSTALLATION INSTRUCTIONS
miniBar
RECORD THIS INFORMATION FOR FUTURE REFERENCE
BEFORE INSTALLING THE UNIT:
Model No.
Serial No.
Product No.
Date Purchased
Place of Purchase
Sales Office
Intercon Marketing
1540 Northgate Blvd.
Sarasotu, Fl 34234
Phone: 941-355-4488
SERVICE OFFICE
The Dometic Corp.
509 So. Poplar St.
La Grange, IN 46761
Phone: 219-463-4858
HiPro 3000
HiPro 4000
HiPro 6000
FOR SERVICE CENTER
ASSISTANCE
CALL: 800 544 4881
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual.
For assistance or additional information consult a qualified
installer or service agency .
IMPORTANT INSTRUCTIONS
READ CAREFULLY
ENGLISH
Type H20 / 60
821 2660-15
T.D. 11/2003
Information
Attention
Environmental
Advice
Warning
© Dometic GmbH - 2002 - Änderungen vorbehalten - Gedruckt in Deutschland
These operating instructions should be kept in a safe place.
If this device is passed on, please include these operating instructions with it.
2
TABLE OF CONTENTS
1.0
INTRODUCTION
4
2.0
FOR YOUR SAFETY
4
2.1
2.2
Warnings and Safety Advice
Coolant
4
4
3.0
WARRANTY AND
CUSTOMER SERVICE
4
4.0
INSTALLATION
5
5.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
The Purpose of this Manual
Tools/Materials Required
Unpacking
Cleaning
Installation
Securing
Connecting the Device to the
Electricity Supply
4.8 Changing the Sliding Hinge
4.9 Changing the Doorhang
4.10 Decor Panel
8
9
10
INSTRUCTION FOR USE
11
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
Initial Operation
Temperature Control
Automatic Defrost Function
Leakage Detection
Postioning the Storage Rack
Interior Light
Automatic Door Control
Check List
Technical Data
Spare Parts
Environmental Advice
Disposal
Energy Saving Tips
3
5
5
5
5
6
7
7
11
11
11
11
12
12
12
13
14
14
15
15
15
1.0
INTRODUCTION
You have made an excellent choice by choosing the Dometic miniBar.
We are convinced that you will be satisfied with your new appliance in every way.
Silent in operation because of the Absorption principle, the miniBar fulfils high quality
standards and guarantees an efficient use of resources and energy during its entire
working life, i.e. during manufacturing, use and disposal.
Please study the installation and operating instructions carefully before
attempting to operate the miniBar.
2.0
2.1
FOR YOUR SAFETY
Warnings and Safety Advice
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
2.2
3.0
In the interests of children's safety:
When disposing of the refrigerator, remove all doors and leave the
shelves inside. This prevents children from being accidentally trapped or
suffocated in the refrigerator.
Never open the cooling unit - it is under high pressure.
Never store explosive substances, such as lighter fuel, petrol, ether or
similar products in the miniBar.
The minibar is not suitable for the proper storage of medications.
The miniBar must be installed in such a way that accidental contact with
the cooling unit (which heats up when in use) is impossible.
The appliance has to be connected to a properly earthed socket in line
with the relevant valid country regulations.
Servicing must only be carried out by authorised service personnel.
Coolant
Ammonia is used as a coolant.
This is a natural compound also used in household cleaning agents (1 litre of
Salmiak cleaner contains up to 200g of ammonia - about twice as much as is
used in the refrigerator). Sodium chromate is used for corrosion protection
(1,8% of the coolant).
If a leak occurs (which can be easily detected due to the unpleasant smell):
Ÿ Switch the device off (pull mains plug, if applicable);
Ÿ Ventilate room thoroughly.
Ÿ Inform hotel personnel.
For the safety of hotel guests and personnel, it has been established by
inspectors that the coolant poses no threat to health.
WARRANTY AND CUSTOMER SERVICE
Warranty arrangements are in accordance with the normal conditions applicable for
the country concerned.
For warranty or other servicing, please contact our Dometic service department.
Any damage due to improper use is not covered by the warranty. The warranty
does not cover any modifications to the appliance or the use of non-original
Dometic parts; the warranty does not apply if the installation and operating
instructions are not adhered to and no liability shall be entertained. Parts can be
ordered from our Dometic service department.
When contacting customer service, please always state model, product number,
4
MLC-Code and serial number !
You can find this information on the model label inside the device.
e.g.
4.0
HiPro 3000
INSTALLATION
4.1
The Purpose of this Manual
4.2
Tools / Materials Required
The manual shows you how to:
Ÿ install the miniBar correctly.
Ÿ operate the miniBar correctly.
Ÿ guarantee the miniBar´s correct maintenance and functioning.
Ÿ deal with faults by yourself.
You will need the following tools for initial operation:
mild detergent
4.3
Unpacking
Check during unpacking that the device is defect-free.
Ÿ Report transport damage to the transport company within 48 hours.
Ÿ Check that the voltage noted on the model label corresponds to the
mains voltage.
Depending on the model, the following parts can be found in the miniBar :
2x
4.4
sliding hinge
Special
Equipment
IR-transmitter
Cleaning
Before operating the miniBar, we recommend you clean it both inside and
outside.
Ÿ Use a soft cloth, lukewarm water and a mild detergent.
Ÿ Following this, wash out the miniBar using clean water and dry thoroughly.
Ÿ At annual intervals, remove dust from fridge aggregate using a brush or
soft cloth.
ATTENTION
To prevent material damage:
Ÿ Do not use soap or detergents which are harsh, coarse or which contain
soda.
Ÿ Keep the door seal free from oil and grease.
Ÿ The cylinder locks have been lubricated in the factory to be long-lasting.
5
4.5
Installation
200 cm²
20 mm
IMPORTANT:
Please follow the installation details below
carefully. Guarantee is valid for products
installed as described only.
1. The refrigerator must be level both directions.
2. There should be 20mm clearance to the wall.
3. Ventilation must be provided as shown in
alternatives A, B, C or D.
4. The ventilation duct must at least measure
105mm x the width of the refrigerator.
5. Only the entire cooling unit must project into
the duct as shown.
6 Air passing through the duct must not be
preheated by any source of heat.
7. Ventilation grills, if used, must have openings
of at least 200cm² each.
The mains plug/socket must be freely accessible once the
miniBar has been installed.
6
4.6
Securing
The miniBar must be screwed
onto the cupboard using the
lower hinges.
Tighten the screws and afix the caps.
4.7
Connecting the Device to the Electricity Supply
Ÿ The device must be connected to a properly earthed
socket in line with the relevant valid country
regulations.
Ÿ The mains plug/socket must be freely accessible.
Ÿ Check prior to initial operation that the voltage
noted on the model label corresponds to the
mains voltage.
If this is not the case, do not connect the
device and contact your dealer!
If the connection cable is damaged it must be replaced by the Customer
Service at Dometic, or by respectively qualified personnel, in order to prevent any hazards.
7
4.8
Changing the Sliding Hinge
1.
2.
1.
2.
3.
4.
Distance to cupboard door (A)
1.
mm
A
2.
mm
1. When closed, the cupboard door (A) must not lie against the rest of the
surrounding cupboard area (distance 1-2mm).
2. There must be a distance of 6-8mm between the cupboard door and the
miniBar.
8
4.9
Changing the Doorhang
(optional) LED
door-opening control always opposite
the hanging side
device with feet
LED
If the miniBar is equipped with the LED first carry out steps a. - e. :
a.
Pull out LED, lay the cable
into the cable routing and
insert the LED at the opposite side.
d.
d. + e.
device with feet
e.
b.
c.
Pull the lower hinges forwards, pull out the door with the hinge..
1.
3.
2.
Remove the upper hinge pin and insert on the other side, change the lower pin in the door.
Then push the door in together with the lower hinge.
4.
6.
5.
9
4.10
Decor panel
4.10.1
Measurements
Thickness
W
0,4 mm
H x W (mm)
RH 030 ltr
492 x 294,5
RH 040 ltr
524 x 311,5
RH 060 ltr
533 x 376,5
h
a
H
Hole for door lock (a)
diameter
O 23,5 mm
distance from the edge (h) 62 mm
4.10.2
Changing the decor panel
A
C
B
-
Loosen the lower door hinge and pull out the door ( see “4.9”).
Remove clamp ring of the doorlock (A) (putted on).
Loosen and remove lower frame piece (B) (not srewed).
Pull out the decor panel (C) with a low curvature.
Push in the new decor panel in such a way that the upper edge runs
exactly parallel to the upper section of the frame.
Put on frame piece (B).
- Put the door on the lower hinge, insert the hinge pin in the door, push in
the door and let the hinge click in.
Note (appliances without doorlock):
- Additional installation of a door lock is possible.
- In the door the position for the opening is prepared.
- Drill the hole in accordance to the drawing above.
10
5.0
5.1
INSTRUCTION for USE
Initial Operation
Ÿ The device must be plugged into a properly
earthed socket.
Ÿ The miniBar starts automatically with a selftest. If the electronics do not detect any
fault, the LED for the interior lighting illuminates for 2 seconds after approximately 10
seconds. If a fault is detected, the illumination changes to a continuous flashing light.
If this occurs, please consult your authorised
Customer Service.
Ÿ The miniBar achieves its operating
temperature after several hours.
The miniBar
operates silently !
5.2
Temperature Control
The miniBar is fitted with an electronic temperature control which works fully
automatically. Manual regulating of the compartment temperature is not possible.
5.3
Automatic Defrost Function
Ÿ The first defrosting phase commences 39 hours after the initial operation
and lasts for two hours.
Ÿ After this, the device operates for 22 hours at a time, followed by a
defrosting period of 2 hours .
T
T
T
S
S
The ice layer must never be removed using force, nor
must the defrosting process ever be accelerated using a
heater.
5.4
Leakage Detection
The electronics carry out a leakage test after every defrosting period
(every 24 hrs) by measuring the temperature at the evaporator by means of
a second sensor.
If the electronics detect a leak, the miniBar is automatically switched off .
The LED for the interior lighting changes after approx. 10 secs. to a continuous flashing. (The LED of the door-opening control flashes synchronously , if available.)
11
5.5
Positioning of the Storage Rack
- Pull out the storage rack until it is blocked.
- Press in the lock of both running rails.
- Remove storage rack and running rails and place it at
the desired position.
- After clicking in the the storage rack it is secured
against pulling out completely again.
1.
5.6
4.
3.
2.
Interior Light
Two LEDs (A) light the cooling compartment whilst the
door is opened.
B
Tow sensors (B) control the
LEDs and the (optional)
door control as well.
5.7
A
Automatic Door Control [ADC] (optional)
The LED (A) placed at the bottom edge of the minibar
indicates whether the miniBar door has been opened.
1. Open the miniBar, check its contents and
- if applicable- stock it up again.
2. Reset the door control sensor by means of an
IR-transmitter.
3. Close the miniBar.
A
LED
A
Infrared - sensor
Infrared - transmitter
12
5.8
Check List
Failure : No cooling (the aggregate at the back of the device is cold).
Possible Cause
Self Help
a.) The device plug is not
plugged in.
a.) Plug in device plug.
b.) No voltage in socket.
b.) Check main fuse.
Authorised Service
c.) Defective electronics or
sensor feelers. LED flashes ?
c.) Install new
electronics or sensor.
d.) Defective heating element.
d.) Install new heating
element.
e.) The device is in its defrosting
phase.
e.) See operating instruction
5.3
Failure : No cooling (the aggregate is warm).
Possible Cause
Self Help
a.) The device is not level.
Leakage test ?
a.) Level the device using a
spirit level.
b.) The device was only
switched on a short while
ago.
b.) Switch on the device and
let it run for 5-6 hours.
c.) Defective cooling unit.
Authorised Service
c.) Exchange device.
Failure : Poor cooling performance.
Possible Cause
Self Help
a.) The cooling aggregate is not
sufficiently ventilated.
a.) Check that the ventilation
grids are not covered.
Check that device has
been installed properly
(installation instruction 4.5).
b.) The device is exposed to
direct sunlight.
b.) Follow installation
instruction 4.5.
c.) The fridge door does not
close tightly
c.) Check installation in line
4.5 + 4.8.
d.) The fridge was stocked a
short while ago.
d.) Check fridge after
5-6 hours for proper
cooling function.
Authorised Service
c.) Install new doorseal,
if necessary.
Failure : Frost formation in fridge.
Possible Cause
Self Help
Authorised Service
a.) The fridge door does not
close tightly.
a.) Check installation is in line
with 4.5 + 4.8.
a.) Install new doorseal,
if necessary.
13
5.9
Technical Data
Model
HiPro 3000
Casing
Plastic material
Gross Contents ( litres)
28
cooled / uncooled
28 / -
Dimensions (mm)
(H x W xD)
527 x 388 x 418
Electrical Rating (W)
65
Power Consumption
kWh / 24h*
0,6
Net Weight (kg)
11
Assembly
x
freestanding
x
Model
HiPro 4000
Casing
Plastic material
Gross Contents ( litres)
37
cooled / uncooled
37 / -
with cooling unit cover + feet
Dimensions (mm)
(H x W xD)
559 x 405 x 452
Electrical Rating (W)
65
601 x 405 x 472
Power Consumption
kWh / 24h*
0,7
Net Weight (kg)
13,5
Assembly
x
freestanding
x
Model
HiPro 6000
Casing
Plastic material
Gross Contents ( litres)
51
cooled / uncooled
51 / -
x
with cooling unit cover + feet
Dimensions (mm)
(H x W xD)
568 x 490 x 474,5
Electrical Rating (W)
65
610 x 490 x 494,6
Power Consumption
kWh / 24h*
0,9
Net Weight (kg)
15
Assembly
x
freestanding
x
x
* Power consumption measured at an average ambient temperature of 25°C as an average
annual value and at a cooling compartment temperature of 7°C in line with EN 153.
We reserve the right to make technical changes and modifications without notice!
5.10
Spare Parts
For spare parts please contact your Dometic Service Center
or your dealer.
14
5.11
Environmental Advice
miniBars manufactured by Dometic GmbH are free from
CFCs / HCFCs and fluorinated hydrocarbons.
The cooling unit uses ammonia as the coolant (a natural compound of
hydrogen and nitrogen). Cyclopentane, which does not damage the ozone
layer, is used as propellant for the insulation made from PU-foam.
5.12
Disposal
In order to ensure the re-use of recyclable packaging materials, these must
be disposed of using local collection systems. The device itself must be
handed over to a disposal company or local council which will guarantee
the correct use of recyclable materials and the proper disposal of the rest.
Energy Saving Tips
5.13
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
If possible, always store pre-cooled goods.
Do not expose the miniBar to direct sunlight and do not place it close
to a source of heat.
An unobstructed air circulation in the fridge aggregate must be
ensured.
When removing goods, only open the miniBar briefly.
Switch on the miniBar approx. 12 hours prior to stocking.
15
Dometic GmbH
In der Steinwiese 16
D-57074 Siegen
GERMANY
Tel.: +49-(0) 271 / 692 0
Fax: +49-(0) 271 / 692 300
www.dometic.de/minibar
www.dometic.com
© Dometic GmbH - 2003 - Subject to change without notice - Printed in Germany
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement