Progress | PEM6000E | User manual | Progress PEM6000E User Manual

user manual
Electric Solid Hob
2 progress
Safety instructions
Description of the Appliance
Operating the hob
Tips on Cooking and Frying
Cleaning and Care
What to do if …
Installation Instructions
Subject to change without notice
Safety instructions
Please comply with these instructions. If
you do not, any damage resulting is not
covered by the warranty.
Correct use
• This appliance is not intended for use by
children or other persons whose physical,
sensory or mental capabilities or lack of
experience and knowledge prevents them
from using the appliance safely without supervision or instruction by a responsible
person to ensure that they can use the appliance safely.
• Do not leave the appliance unattended
during operation.
• This appliance should be used only for
normal domestic cooking and frying of
• The appliance must not be used as a work
surface or as a storage surface.
• Additions or modifications to the appliance
are not permitted.
• Do not place or store flammable liquids,
highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium)
on or near the appliance.
Children’s safety
• Small children must be kept away from the
• Only let bigger children work on the appliance under supervision.
General safety
• The appliance may only be installed and
connected by trained, registered service
engineers .
• Built-in appliances may only be used after
they have built in to suitable built-in units
and work surfaces that meet standards.
• If there is a fault with the appliance, all hotplates must be switched off and the appliance must be disconnected from the
mains supply to avoid any possible electric
• Repairs to the appliance must only be carried out by trained, registered service engineers.
Safety during use
• There is the risk of burns from the appliance if used carelessly.
• Cables from electrical appliances must not
touch the hot surface of the appliance or
hot cookware.
• Overheated fats and oils can ignite quickly.
When cooking with fat or oil (e.g when frying chips) do not leave the appliance unattended.
• Switch the hotplates off after each use.
Safety when cleaning
• For cleaning, the appliance must be
switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or high-pressure
cleaning equipment is not permitted.
How to avoid damage to the appliance
• Do not allow acid liquids such as vinegar,
lemon juice or limescale removing agents
to touch the hob, as otherwise this will
cause matt patches.
• Do not place wet pan lids on the hotplates
and do not allow hot pans to cool on the
hotplates. Otherwise condensation and
rust can form.
• Do not use the hotplates with empty cookware or without cookware.
progress 3
Description of the Appliance
Solid Hotplate 1000W
Quick Hotplate 2000W
Solid Hotplate 1000W
Quick Hotplate 2000W
Operating the hob
You operate the appliance with the combination appliance’s ring switches. The
operation and the function of the ring
switches is described in the Operating
Instructions for the combination appliance.
Warning! The hotplates still remain hot
for a time even after being switched off.
There is a risk of burns. Let the hotplates
cool down.
Tips on Cooking and Frying
Information on acrylamides
According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can
constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures
and not browning foods too much.
You can recognise good cookware from the
bottoms of the pans. The bottom should be
as thick and flat as possible.
Energy saving
Always place cookware on the cooking
zone before it is switched on.
If possible, always place lids on the
Switch cooking zones off before the end
of the cooking time, to take advantage
of residual heat.
Bottom of pans and cooking zones
should be the same size.
4 progress
Cleaning and Care
Warning! Risk of burns from residual
heat. Let the appliance cool down.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth
and a little washing up liquid.
2. Rub the appliance dry using a clean cloth.
Removing deposits
1. Remove heavy deposits from the hotplates using fine scouring powder or a
scouring pad.
2. Wipe off residues with a damp cloth.
3. Then heat the hotplate to a low temperature and leave to dry.
4. To maintain the hotplates, rub in a little
sewing machine oil now and again and
then polish off with absorbent paper.
Warning! Do not clean the stainless
steel edge of the hob with scouring
powder or a scouring pad as this will
leave scratches! For stainless steel hobs
only use suitable stainless steel cleaning
and maintenance products. Please the
manufacturer’s instructions.
The stainless steel edge of the plate can
be slightly discoloured as a result of thermal load. This process is caused by the
physical properties.
What to do if …
The hotplates are not functioning
Possible cause
The combination appliance is
not switched on
Switch on the appliance.
The desired heat setting is not
Set the heat setting.
The fuse in the house’s electrical Check the fuse. If the fuses trip
wiring (fuse box) has been trip- a number of times, please call an
authorized electrician.
If you are unable to remedy the problem
by following the above suggestions,
please contact your dealer or the Customer Care Department.
Warning! Repairs to the appliance are
only to be carried out by qualified service
engineers. Considerable danger to the
user may result from improper repairs.
If the appliance has been wrongly operated, the visit from the customer service
technician or dealer may not take place
free of charge, even during the warranty
The symbol
on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
progress 5
Installation Instructions
Safety instructions
Warning! This must be read!
The laws, ordinances, directives and standards in force in the country of use are to be
followed (safety regulations, proper recycling
in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to
other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers
may only be installed with a protective floor
directly underneath the appliance. The cut
surfaces of the worktop are to be protected
against moisture using a suitable sealant.
The sealant seals the appliance to the work
top with no gap. When building in, protect the
underside of the appliance from steam and
moisture, e.g. from a dishwasher or oven.
Avoid installing the appliance next to doors
and under windows. Otherwise hot cookware may be knocked off the rings when
doors and windows are opened.
Warning! Risk of injury from electrical
• The electrical mains terminal is live.
• Make electrical mains terminal free of
• Follow connection schematic.
• Observe electrical safety rules.
min. 500mm
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to
the electrical supply by a qualified
Warning! Risk of injury from electrical
• Loose and inappropriate plug and
socket connections can make the terminal overheat.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or twophase connection, the appropriate
mains cable of type H05BB-F Tmax
90°C (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a special
cable (type H05BB-F Tmax 90°C; or
higher). The latter is available from the
Customer Care Department
A device must be provided in the electrical
installation which allows the appliance to be
disconnected from the mains at all poles with
a contact opening width of at least 3 mm.
Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are
to be removed from the holder), earth leakage trips and contractors.
6 progress
PEM 6000 E
230 V
949 592 995
50 Hz
6,0 kW
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number
(S No. - see rating plate)
– Type of fault
– Any error messages displayed by
the appliance
– three digit letter-number combination
for glass ceramic
progress 7
Download PDF