Progress | PAI6000E | User manual | Progress PAI6000E User Manual

user manual
Ceramic glass induction hob
PAI6000E
2 progress
Contents
Safety Information
Description of the Appliance
Operating the appliance
Tips on Cooking and Frying
Cleaning and Care
2
3
4
8
10
What to do if ...
Disposal
Installation Instructions
Service
11
12
12
14
Subject to change without notice
Safety Information
Warning! Please comply with these
instructions. If you do not, any damage
resulting is not covered by the warranty.
Correct use
• This appliance is not intended for use by
children or other persons whose physical,
sensory or mental capabilities or lack of
experience and knowledge prevents them
from using the appliance safely without supervision or instruction by a responsible
person to ensure that they can use the appliance safely.
• Do not leave the appliance unattended
during operation.
• This appliance should be used only for
normal domestic cooking and frying of
food.
• The appliance must not be used as a work
surface or as a storage surface.
• Additions or modifications to the appliance
are not permitted.
• Do not place or store flammable liquids,
highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium)
on or near the appliance.
Children’s safety
• Small children must be kept away from the
appliance.
• Only let bigger children work on the appliance under supervision.
• To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device.
General safety
• The appliance may only be installed and
connected by trained, registered service
engineers.
• Built-in appliances may only be used after
they have built in to suitable built-in units
and work surfaces that meet standards.
• In the event of faults with the appliance or
damage to the glass ceramic (cracks,
scratches or splits), the appliance must be
switched off and disconnected from the
electrical supply, to prevent the possibility
of an electric shock.
• Repairs to the appliance must only be carried out by trained registered service engineers.
Safety during use
• Remove stickers and film from the glass
ceramic.
• There is the risk of burns from the appliance if used carelessly.
• Cables from electrical appliances must not
touch the hot surface of the appliance or
hot cookware.
• Overheated fats and oils can ignite very
quickly. Warning! Fire hazard!
• Switch the cooking zones off after each
use.
• Users with implanted pacemakers should
keep their upper body at least 30 cm from
induction cooking zones that are switched
on.
• Risk of burns! Do not place objects made
of metal, such as knives, forks, spoons
and saucepan lids on the cooking surface,
as they can get hot.
Safety when cleaning
• For cleaning, the appliance must be
switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or high-pressure
cleaning equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by
objects falling onto it.
• The edge of the glass ceramic can be
damaged by being knocked by the cookware.
progress 3
• To avoid damaging cookware and glass
ceramics, do not allow saucepans or frying
pans to boil dry.
• The ventilation gap of 5mm between the
worktop and front of the unit underneath it
must not be covered.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can
scratch the glass ceramic if pushed across
the surface.
• Objects that melt and things that boil over
can burn onto the glass ceramic and
should be removed straightaway.
• Do not use the cooking zones with empty
cookware or without cookware.
Description of the Appliance
Cooking surface layout
1
2
m
1. Induction cooking zone 1400 W
2. Induction cooking zone 1800 W
3. Induction cooking zone 1800 W with
power function 2800 W
4. Control panel
5. Induction cooking zone 2200 W with
power function 3100 W
m
0m
0m
14
18
m
0m
m
18
m
10
2
5
4
3
Control panel layout
1
2
3
8
1.
2.
3.
4.
Display
Heat setting selection
Cooking zone indicators Timer function
Timer display
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions are controlled by
4
7
6
5.
6.
7.
8.
5
Power indication
Lock
Timer
On/Off with power indicator
touching sensor fields and confirmed by displays and acoustic signals.
Touch the sensor fields from above, without
covering other sensor fields.
4 progress
Sensor field
Function
On / Off
To switch the appliance on and off
Increase settings
Increasing heat setting/time
Decrease settings
Decreasing heat setting/time
Timer
Timer selection
Lock
Locking/unlocking the control panel
Power
Switching the power function on and off
Displays
Display
Description
Cooking zone is switched off
Heat settings
Heat setting is set
Fault
Malfunction has occurred
Pan detection
Cookware is unsuitable or too small or no cookware has
been placed on the cooking zone
Residual heat
Cooking zone is still hot
Child safety device
Lock/child safety device is engaged
Power
Power function is switched on
Automatic switch off
Switch off is active.
Residual heat indicator
Warning! Risk of burns from residual
heat. After being switched off, the
cooking zones need some time to cool
down. Look at the residual heat indicator
.
The induction cooking zones create the
heat required for cooking directly in the base
of the cookware. The glass ceramic is merely
heated by the residual heat of the cookware.
The cooling fan switches itself on and off
depending upon the temperature of the electronics.
Residual heat can be used for melting
and keeping food warm.
Operating the appliance
Use the induction cooking zones with
suitable cookware.
Switching the appliance on and off
Control panel
Switch on
Touch
for 2 seconds
Switch off
Touch
for 1 second
After switching on, within approx. 10
seconds a heat setting or a function
Display
/
/ none
must be set, otherwise the appliance automatically switches itself off.
progress 5
Setting the heat setting
Control panel
Increase
Touch
Decrease
Touch
Switch off
Touch
Display
to
/
to
and
at the same time
Locking/unlocking the control panel
The control panel, with the exception of the
“On/Off” sensor field, can be locked at any
time in order to prevent the settings being
changed e.g. by wiping over the panel with a
cloth.
Control panel
Switch on
Touch
Switch off
Touch
When you switch the appliance off, the
locking function is automatically switched off.
Display
(for 5 seconds)
previously set heat setting
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Setting the child safety device
Step
1.
Control panel
Display/Signal
Switch on the appliance (Do not set a heat setting)
2.
Touch
3.
Touch
Acoustic signal
until the signal sounds
Appliance switches off. The child safety device is engaged.
Overriding the child safety device
The child safety device can be released in this
way for a single cooking session; it remains
activated afterwards.
Step
1.
2.
Control panel
Display/Signal
Switch on the appliance
Touch
and
at the same time
/ acoustic signal
Until the appliance is next switched off, it can used as normal.
Releasing the child safety device
Step
1.
Control panel
Display/Signal
Switch on the appliance
2.
Touch
3.
Touch
Acoustic signal
until the signal sounds
Appliance switches off. The child safety device is released.
Switching the power function on and off
makes additional
The power function
power available to the front induction cooking zones, e.g. to bring a large volume of water to the boil. The power function is activated
for 8 minutes for the front left cooking zone
and for 5 minutes for the front right cooking
zone. After these times, the induction cooking zones automatically return to cooking level .
6 progress
Control panel
Switch on
Touch
Switch off
Touch
Display
Touch
If the power function has ended, the
cooking zones automatically switch
back to the heat setting set previously.
Power Management
The cooking zones of the cooking surface
have a maximum power available to them.
Two cooking zones make up a pair (see figure).
So that the Power function can always be
carried out, Power Management may reduce
the power of the other cooking zone in the
pair
Example: heat setting 9 is selected on a
cooking zone. The Power function is switched on for the cooking zone paired up with it.
The Power function is performed, but heat
setting 9 on one cooking zone and Power
function on the other cooking zone of a pair
exceeds the maximum output for both.
Therefore Power Management reduces the
first cooking zone that was switched on from
9 to 7, for example, and the display for this
cooking zone alternates between 9 and 7
and then remains on the current maximum of
7. (Whether the display alternates between 9
and 7 or 9 and 6 or other values, depends on
the appliance type and the size of the cooking zone.)
Using the timer
All cooking zones can use each use one of
the two timer functions at the same time.
Function
Condition
Outcome after the time has
elapsed
Automatic cut-out
a heat setting is set
acoustic signal 00 flashes Cooking
zone switches off
Countdown timer
cooking zones not in use
acoustic signal 00 flashes
If a cooking zone is switched off, the timer function set is also switched off.
the cooking zone is switched off after the
time set has elapsed.
If a heat setting is set on this cooking
zone in addition to a countdown timer,
Selecting a cooking zone
Ste
p
Control panel
1.
Touch once
Display
Pilot light of the first cooking zone flashes
progress 7
Ste
p
Control panel
Display
2.
Touch once
Pilot light of the second cooking zone flashes
3.
Touch once
Pilot light of the third cooking zone flashes
4.
Touch once
Pilot light of the fourth cooking zone flashes
The heat setting indicator of the selected
cooking zone goes out, as long as the
timer time can be set.
If other timer functions are set, after a
few seconds the shortest remaining time
of all the timer functions is displayed and
the corresponding pilot light flashes.
If the pilot light is flashing more slowly,
the heat setting indicator appears again
and the heat setting can be re-set or
modified.
Setting time
Step
1.
Control panel
Grill seting
Telltale of cooking zone selected flashes
Selecting cooking zone
2.
Touch
zone
3.
Touch
or
from the selected cooking
zone for more than 4 seconds
or
from the selected cooking
01 to 99 minutes
5-minute steps for easy setting
After a few seconds the power indicator flashes more slowly.
The time is set.
The time counts down.
Switching off the Timer function
Step
1.
Control panel
Display
Pilot light of the selected cooking zone
flashes more quickly. Remaining time is displayed
Select a cooking zone
2.
Touch
The remaining time counts down to 00.
for the cooking zone selected
The pilot light goes out.
The Timer function for the selected cooking zone is switched off.
Changing the time
Step
1.
2.
Control panel field
Select cooking zone
Touch
or
selected
for the cooking zone
Display
Pilot light of the cooking zone selected flashes
faster The time remaining is displayed
01 to 99 minutes
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
8 progress
Displaying the time remaining for a cooking zone
Step
Control panel field
1.
Select cooking zone
Display
Pilot light of the cooking zone selected flashes
faster The time remaining is displayed
After a few seconds the pilot light flashes more slowly.
Switching off the acoustic signal
Step
1.
Control panel field
Acoustic signal
Acoustic signal to acknowledge.
Touch
Acoustic signal stops.
Automatic switch off
• If after switching on the cooking surface, a
heat setting is not set for a cooking zone
within approx. 10 seconds, the cooking
surface automatically switches itself off.
• If all cooking zones are switched off, the
cooking surface automatically switches itself off after approx. 10 seconds.
Induction cooking zones
• If cookware that is not suitable is used,
lights up in the display and after 2 mi-
nutes the indicator for the cooking zone
switches itself off.
• If one of the cooking zones is not switched
off after a certain time, or if the heat setting
is not modified, the relevant cooking zone
switches off automatically. is displayed.
Before being used again, the cooking zone
must be set to 0.
Heat setting
Switches off after
-
6 hours
-
5 hours
-
1.5 hours
4 hours
Tips on Cooking and Frying
Information on acrylamides
According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can
constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures
and not browning foods too much.
Cookware for induction cooking zones
Cookware material
Cookware material
Steel, enamelled steel
Cast iron
Stainless steel
Suitable
yes
yes
if appropriately labelled by the manufacturer
Aluminium, copper, brass
---
Glass, ceramic, porcelain
---
Cookware for induction cooking zones
is labelled as suitable by the manufacturer.
Suitability test
Cookware is suitable for induction cooking, if
…
progress 9
• ... a little water on an induction cooking
zone set to heat setting 9 is heated within
a short time.
• ... a magnet sticks to the bottom of the
cookware.
Certain cookware can make noises
when being used on induction cooking
zones. These noises are not a fault in the
appliance and do not affect operation in
any way.
Bottom of the cookware
The bottom of the cookware should be as
thick and flat as possible.
Pan size
Induction cooking zones adapt automatically
to the size of the bottom of the cookware up
to a certain limit. However the magnetic part
of the bottom of the cookware must have a
minimum diameter depending upon the size
of the cooking zone.
Diameter of cooking zone [mm]
Minimum diameter of dish base [mm]
210
180
180
145
145
120
The cookware must be placed centrally
on the cooking zone.
Tips on energy saving
Place cookware on the cooking zone
before it is switched on.
Heat setting
Cooking process
0
If possible, always place a lid on the
cookware.
Examples of cooking applications
The information given in the following table is
for guidance only.
Suitable for
Cooking time
Tips/Hints
Off position
1
Keeping food
warm
Keeping cooked
foods warm
as required
Cover
1-2
Melting
Hollandaise sauce,
melting butter,
chocolate, gelatine
5-25 mins.
Stir occasionally
Solidifying
Fluffy omelettes,
baked eggs
10-40 mins.
Cook with lid on
2-3
Simmering on low
heat
Simmering rice and
milkbased dishes
Heating up readycooked meals
25-50 mins.
Add at least twice
as much liquid as
rice, stir milk dishes
part way through
cooking
3-4
Steaming Braising
Steaming vegetables, fish braising
meat
20-45 mins.
With vegetables
add only a little liquid (a few tablespoons)
4-5
Boiling
Steaming potatoes
20-60 mins.
Use only a little liquid, e. g.: max. ¼ l
water for 750 g potatoes
Cooking larger
quantities of food,
stews and soups
60-150 mins.
Up to 3 l liquid plus
ingredients
10 progress
Heat setting
Cooking process
Suitable for
Cooking time
Tips/Hints
6-7
Gentle Frying
Frying escalopes,
veal cordon bleu,
cutlets, rissoles,
sausages, liver,
roux, eggs, pancakes, doughnuts
Steady frying
Turn halfway
through cooking
7-8
Heavy Frying
Hash browns, loin
steaks, steaks, Flädle (pancakes for
garnishing soup)
5-15 mins. per pan
Turn halfway
through cooking
9
Boiling Searing
Deep frying
Boiling large quantities of water, cooking pasta, searing meat
(goulash, pot roast), deep frying chips
The power function is suitable for heating
large quantities of liquid.
Cleaning and Care
Warning! Risk of burns from residual
heat.
Warning! Sharp objects and abrasive
cleaning materials will damage the
appliance. Clean with water and
washing up liquid.
Warning! Residues from cleaning
agents will damage the appliance.
Remove residues with water and
washing up liquid.
2. Rub the appliance dry using a clean cloth.
Removing deposits
1. Place a scraper on the glass ceramic surface at an angle.
2. Remove residues by sliding the blade
over the surface.
3. Wipe the appliance with a damp cloth
and a little washing up liquid.
4. Rub the appliance dry using a clean cloth.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth
and a little washing up liquid.
Remove
Type of dirt
immediately
when the appliance
has cooled down
using
sugar, food containing
sugar
yes
---
a scraper *
plastics, tin foil
yes
---
a scraper *
limescale and water
rings
---
yes
cleaner for glass ceramic
or stainless steel *
fat splashes
---
yes
cleaner for glass ceramic
or stainless steel *
shiny metallic discoloration
---
yes
cleaner for glass ceramic
or stainless steel *
* Scrapers and cleaners for glass ceramic
and stainless steel can be purchased in specialist shops
Remove stubborn residues with a cleaner for glass ceramic or stainless steel.
Scratches or dark stains on the glass
ceramic that cannot be removed do not
however affect the functioning of the appliance.
progress 11
What to do if ...
Problem
Possible cause
Remedy
The appliance cannot be switch- More than 10 seconds have
Switch the appliance on again.
ed on or is not operating
passed since the appliance was
switched on
The lock is switched on
Switch off the lock (See the section “Locking/unlocking the control panel”)
The child safety device is switched on
Deactivate child safety device
(See the section “Child safety
device”)
Several sensor fields were
touched at the same time
Only touch one sensor field
Automatic switch off has been
triggered
Remove any objects (pan,
cloths, etc.) that are lying on the
control panel. Switch the appliance on again
The cooking zones automatical- The sensor fields are partly cov- Remove the cloth or the liquid.
ly reduce the cooking level to
ered by a damp cloth or with liq- Reset the cooking level required.
uid
The residual heat indicator is not
displaying anything
The cooking zone was only on
for a short time and is therefore
not hot
If the cooking zone is supposed
to be hot, call the Customer
Service Department.
acoustic signal sounds, appliance switches off
One or more sensor fields have
been covered for longer than 10
seconds
Uncover sensor field
Acoustic signal sounds and ap- The On/Off sensor field has
pliance switches itself on and af- been covered up, e.g. by a cloth
ter 10 seconds off again
Display is switching between
two heat settings
lights up
Do not place any objects on the
control panel
Power management is reducing See the section “Switching the
the power of this cooking zone power function on and off”
Unsuitable cookware
Use suitable cookware
No cookware on the cooking
zone
Place cookware on the cooking
zone
The diameter of the bottom of
the cookware is too small for the
cooking zone
Move onto a smaller cooking
zone
Use suitable cookware
is lit
Overheating protection for the
cooking zone has been triggered
Switch off the cooking zone.
Switch the cooking zone on
again
Automatic switch off has been
triggered
Switch off the cooking zone.
Switch the cooking zone on
again
12 progress
Problem
and number are displayed
Possible cause
Electronics fault
If you are unable to remedy the problem
by following the above suggestions,
please contact your dealer or the Customer Care Department.
Warning! Repairs to the appliance are
only to be carried out by qualified service
engineers. Considerable danger to the
user may result from improper repairs.
Remedy
Disconnect the appliance from
the electrical supply for a few minutes (Take the fuse out of the
house’s wiring system) If after
switching on again,
is displayed again, call the customer
service department
If the appliance has been wrongly operated, the visit from the customer service
technician or dealer may not take place
free of charge, even during the warranty
period.
Disposal
The symbol
on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Installation Instructions
Safety instructions
Warning! This must be read!
The laws, ordinances, directives and standards in force in the country of use are to be
followed (safety regulations, proper recycling
in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to
other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers
may only be installed with a protective floor
directly underneath the appliance. The cut
surfaces of the worktop are to be protected
against moisture using a suitable sealant.
The sealant seals the appliance to the work
top with no gap. When building in, protect the
underside of the appliance from steam and
moisture, e.g. from a dishwasher or oven.
Avoid installing the appliance next to doors
and under windows. Otherwise hot cook-
ware may be knocked off the rings when
doors and windows are opened.
Warning! Risk of injury from electrical
current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of
voltage.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to
the electrical supply by a qualified
electrician.
progress 13
Warning! Risk of injury from electrical
current.
• Loose and inappropriate plug and
socket connections can make the terminal overheat.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or twophase connection, the appropriate
mains cable of type H05BB-F Tmax
90°C (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a special
cable (type H05BB-F Tmax 90°C; or
higher). The latter is available from the
Customer Care Department.
A device must be provided in the electrical
installation which allows the appliance to be
disconnected from the mains at all poles with
a contact opening width of at least 3 mm.
Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are
to be removed from the holder), earth leakage trips and contractors.
min.
50 mm
min. 5 mm
2
1
60
0
1
49
0+
56
0+
1
R5
14 progress
PAI 6000 E
55GADD5AU
230 V
50 Hz
949 593 002
Induction 7,2 kW
7,2 kW
PROGRESS
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number
(S No. - see rating plate)
– Type of fault
– Any error messages displayed by
the appliance
– three digit letter-number combination
for glass ceramic
progress 15
www.progress-hausgeraete.de
867201557-B-052008
Download PDF

advertising