Progress | PAS8060E | User manual | Progress PAS8060E User Manual

user manual
Ceramic Glass Hob
PAS8060E
2 progress
Contents
Safety instructions
Description of the Appliance
Operating the appliance
Tips on Cooking and Frying
Cleaning and Care
2
3
4
8
10
What to do if ...
Disposal
Installation Instructions
Service
11
12
12
13
Subject to change without notice
Safety instructions
Warning! Please comply with these
instructions. If you do not, any damage
resulting is not covered by the warranty.
Correct use
• This appliance is not intended for use by
children or other persons whose physical,
sensory or mental capabilities or lack of
experience and knowledge prevents them
from using the appliance safely without supervision or instruction by a responsible
person to ensure that they can use the appliance safely.
• Do not leave the appliance unattended
during operation.
• This appliance should be used only for
normal domestic cooking and frying of
food.
• The appliance must not be used as a work
surface or as a storage surface
• Additions or modifications to the appliance
are not permitted.
• Do not place or store flammable liquids,
highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium)
on or near the appliance.
Children’s safety
• Small children must be kept away from the
appliance.
• Only let bigger children work on the appliance under supervision.
• To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device.
General safety
• The appliance may only be installed and
connected by trained, registered service
engineers.
• Built-in appliances may only be used after
they have built in to suitable built-in units
and work surfaces that meet standards.
• In the event of faults with the appliance or
damage to the glass ceramic (cracks,
scratches or splits), the appliance must be
switched off and disconnected from the
electrical supply, to prevent the possibility
of an electric shock.
• Repairs to the appliance must only be carried out by trained registered service engineers.
Safety during use
• Overheated fats and oils can ignite very
quickly. Warning! Fire hazard!
• There is the risk of burns from the appliance if used carelessly.
• Remove stickers and film from the glass
ceramic.
• Cables from electrical appliances must not
touch the hot surface of the appliance or
hot cookware.
• Switch the cooking zones off after each
use.
• Risk of burns! Do not place objects made
of metal, such as knives, forks, spoons
and saucepan lids on the cooking surface,
as they can get hot.
Safety when cleaning
• For cleaning, the appliance must be
switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or highpressure
cleaning equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by
objects falling onto it.
• The edge of the glass ceramic can be
damaged by being knocked by the cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can
scratch the glass ceramic if pushed across
the surface.
progress 3
• Objects that melt and things that boil over
can burn onto the glass ceramic and
should be removed straightaway.
• To avoid damaging cookware and glass
ceramics, do not allow saucepans or frying
pans to boil dry.
• Do not use the cooking zones with empty
cookware or without cookware.
Description of the Appliance
Cooking surface layout
2
1
m
5m
1.
2.
3.
4.
5.
265/170 mm
14
Single cooking zone 1200 W
Multi-purpose zone 1500/2400 W
Single cooking zone 1200 W
Control panel
Double ring cooking zone 750/2200 W
m
m
5m
0m
14
2
0/1
21
5
4
3
Control panel layout
1
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
8
7
2
3
4
6
Heat setting selection
Heat setting indicator
Cooking zone indicators Timer function
Timer display
Multi-purpose zone switch with pilot ligh
Timer
Double ring cooking zone switch with pilot light
Lock with pilot light
On/Off with power indicator
5
4 progress
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions are controlled by
touching sensor fields and confirmed by displays and acoustic signals.
Touch the sensor fields from above, without
covering other sensor fields.
Sensor field
Function
On / Off
To switch the appliance on and off
Increase settings
Increasing heat setting/time
Decrease settings
Decreasing heat setting/time
Timer
Timer selection
Lock
Locking/unlocking the control panel
Double ring switch
Switches outside ring on and off
Multi-purpose zone switch
To switch the outside ring on and off
Displays
Display
Description
Cooking zone is switched off
Keep warm setting
Keep warm setting is set
Heat settings
Heat setting is set
Automatic warm up function
Automatic warm-up function is activated
Fault
Malfunction has occurred
Residual heat
Cooking zone is still hot
Child safety device
Lock/child safety device is engaged
Automatic switch off
Switch off is active.
down. Look at the residual heat indicator
.
Residual heat indicator
Warning! Risk of burns from residual
heat. After being switched off, the
cooking zones need some time to cool
Residual heat can be used for melting
and keeping food warm.
Operating the appliance
Switching the appliance on and off
Control panel
Display
Pilot light
Switch on
Touch
for 2 seconds
/
lights up
Switch off
Touch
for 1 second
/ none
goes out
After switching on, within approx. 10
seconds a heat setting or a function
Setting the heat setting
must be set, otherwise the appliance automatically switches itself off.
Control panel
Indicator
To increase
Touch
to
To decrease
Touch
to
progress 5
Control panel
To switch off
Touch
and
Indicator
at the same time
The keep warm setting
lies between
and . It is used to keep food warm.
Before an outside ring can be switched
on, the inside ring must be switched on.
Switching the outside ring on and off
By switching the outside rings on or off, the
effective heating surface can be matched to
the size of the cookware.
Double ring cooking zone
Sensor field
Pilot light
To switch on outside ring
Touch
for 1-2 seconds
is lit
To switch off outside ring
Touch
for 1-2 seconds
goes out
Roasting zone
Sensor panel
Power indicator
To switch on outside ring
Touch
for 1-2 seconds
is lit
To switch off outside ring
Touch
for 1-2 seconds
goes out
time in order to prevent the settings being
changed e.g. by wiping over the panel with a
cloth.
Locking/unlocking the control panel
The control panel, with the exception of the
“On/Off” sensor field, can be locked at any
Control panel
Switch on
Switch off
Display
Touch
(for 5 seconds)
previously set heat setting
Touch
When you switch the appliance off, the
locking function is automatically switched off.
Using the automatic warm-up function
All cooking zones are equipped with an automatic warm up function When setting a
, when starting from
heat setting using
Control panel
, the cooking zone switches to full power
for a certain amount of time and then automatically switches back to the heat setting
set.
Possible heat settings
Switch on (only when
starting at
)
Touch
to
Switch off
Touch
to
Not used
Touch
to
If during the automatic warm up
a
higher heat setting is selected, e.g. from
to , the automatic warm up is adjusted.
If there is still residual heat on the cooking zone (display
), the automatic
warm up is not performed.
Display
(after 5 seconds)
/
to
to
The length of time that the automatic warm
up function operates depends on the heat
setting selected.
6 progress
Heat setting
Length of the automatic warm up [min:sec]
0:30
1:00
1:40
4:50
6:30
10:10
2:00
3:30
4:30
---
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Switching on the child safety device
Step
1.
Control panel
Display/Signal
Switch on appliance. (Do not set a heat setting.)
2.
Touch
for 4 seconds
The child safety device is switched on.
Switching off the child safety device
Step
1.
Control panel
Display/Signal
Switch on appliance. (Do not set a heat setting.)
2.
Touch
3.
for 4 seconds
lights up
Switch appliance off.
The child safety device is switched off.
The child safety device can only be
switched on and off, if no heat setting is
set.
Overriding the child safety device
The child safety device can be switched off
in this way for a single cooking session; it remains activated afterwards.
Step
1.
2.
Control panel
Display/Signal
Switch appliance on
Touch
for 4 seconds
lights up
Until the appliance is next switched off, it can used as normal. After switching off the appliance, the
child safety device is active again.
progress 7
After overriding the child safety device, a
heat setting or a function must be set
within approx. 10 seconds, otherwise
Using the timer
Function
Condition
the appliance automatically switches itself off.
Outcome after the time has elapsed
Automatic cut-out
a heat setting is set
acoustic signal 00 flashes Cooking zone
switches off
Countdown timer
cooking zones not in use
acoustic signal 00 flashes
If a heat setting is set on this cooking
zone in addition to a countdown timer,
the cooking zone is switched off after the
time set has elapsed.
Selecting a cooking zone
Step
Control panel
If a cooking zone is switched off, the timer function set is also switched off.
Display
1.
Touch
once
Pilot light of the first cooking zone flashes
2.
Touch
once
Pilot light of the second cooking zone flashes
3.
Touch
once
Pilot light of the third cooking zone flashes
4.
Touch
once
Pilot light of the fourth cooking zone flashes
If the pilot light is flashing more slowly,
the heat setting can be set or modified.
of all the timer functions is displayed and
the corresponding pilot light flashes.
If other timer functions are set, after a
few seconds the shortest remaining time
Setting the time
Step
Control panel
Indicator
1.
Select
cooking zone
Pilot light for the cooking zone selected flashes
2.
Touch
or
00 to 99 minutes
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Switching off the timer function
Step
Control panel
1.
Select
2.
Touch
cooking zone
Indicator
Pilot light of cooking zone selected flashes faster.
Time remaining is displayed
The time remaining counts backwards to 00 .
The pilot light goes out.
The Timer function for the selected cooking zone is switched off.
8 progress
Changing the time
Control panel
Indicator
1.
Step
Select
cooking zone
Pilot light of the selected cooking zone flashes faster
Time remaining is displayed
2.
Touch
or
01 to 99 minutes
After a few seconds, the pilot light flashes more slowly.
The time is set.
The time counts down.
Displaying the time remaining for a cooking zone
Step
1.
Select
Control panel field
Display
cooking zone
Pilot light of the cooking zone selected flashes faster
The time remaining is displayed
After a few seconds the pilot light flashes more slowly.
Switching off the acoustic signal
Step
1.
Control panel field
Acoustic signal
Acoustic signal to acknowledge.
Touch
Acoustic signal stops.
Automatic switch off
Cooking surface
• If after switching on the cooking surface, a
heat setting is not set for a cooking zone
within approx. 10 seconds, the cooking
surface automatically switches itself off.
• If one or more sensor fields are covered by
objects (a pan, cloths, etc.) for longer than
approx. 10 seconds, a signal sounds and
the cooking surface switches off automatically.
Heat setting
,
-
• If all cooking zones are switched off, the
cooking surface automatically switches itself off after approx. 10 seconds.
Cooking zones
If one of the cooking zones is not switched
off after a certain time, or if the heat setting is
not modified, the relevant cooking zone
switches off automatically.
is displayed.
Before being used again, the cooking zone
.
must be set to
Switches off after
6 hours
5 hours
4 hours
-
1.5 hours
Tips on Cooking and Frying
Information on acrylamides
According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can
constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures
and not browning foods too much.
Cookware
• You can recognise good cookware from
the bottoms of the pans. The bottom
should be as thick and flat as possible.
• Cookware made of enamelled steel or with
aluminium or copper bottoms can leave
discolorations on the glass ceramic surface which are difficult or impossible to remove.
progress 9
Always place cookware on the cooking
zone before it is switched on.
Energy saving
If possible, always place lids on the
pans.
Switch cooking zones off before the end
of the cooking time, to take advantage
of residual heat.
Bottom of pans and cooking zones
should be the same size.
Examples of cooking applications
The information given in the following table is
for guidance only.
Heat setting
Cooking process
0
Suitable for
Cooking time
Tips/Hints
Off position
Keeping food
warm
Keeping cooked
foods warm
as required
Cover
Melting
Hollandaise sauce,
melting butter,
chocolate, gelatine
5-25 mins.
Stir occasionally
Solidifying
Fluffy omelettes,
baked eggs
10-40 mins.
Cook with lid on
2-3
Simmering on low
heat
Simmering rice and
milkbased dishes
Heating up readycooked meals
25-50 mins.
Add at least twice
as much liquid as
rice, stir milk dishes
part way through
cooking
3-4
Steaming Braising
Steaming vegetables, fish braising
meat
20-45 mins.
With vegetables
add only a little liquid (a few tablespoons)
4-5
Boiling
Steaming potatoes
20-60 mins.
Use only a little liquid, e. g.: max. ¼ l
water for 750 g potatoes
Cooking larger
quantities of food,
stews and soups
60-150 mins.
Up to 3 l liquid plus
ingredients
1-2
10 progress
Heat setting
Cooking process
Suitable for
Cooking time
Tips/Hints
6-7
Gentle Frying
Frying escalopes,
veal cordon bleu,
cutlets, rissoles,
sausages, liver,
roux, eggs, pancakes, doughnuts
Steady frying
Turn halfway
through cooking
7-8
Heavy Frying
Hash browns, loin
steaks, steaks, Flädle (pancakes for
garnishing soup)
5-15 mins. per pan
Turn halfway
through cooking
9
Boiling Searing
Deep frying
Boiling large quantities of water, cooking pasta, searing meat
(goulash, pot roast), deep frying chips
Cleaning and Care
Warning! Risk of burns from residual
heat.
Warning! Sharp objects and abrasive
cleaning materials will damage the
appliance. Clean with water and
washing up liquid.
Warning! Residues from cleaning
agents will damage the appliance.
Remove residues with water and
washing up liquid.
2. Rub the appliance dry using a clean cloth.
Removing deposits
1. Place a scraper on the glass ceramic surface at an angle.
2. Remove residues by sliding the blade
over the surface.
3. Wipe the appliance with a damp cloth
and a little washing up liquid.
4. Rub the appliance dry using a clean cloth.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth
and a little washing up liquid.
Remove
Type of dirt
immediately
when the appliance
has cooled down
using
sugar, food containing
sugar
yes
---
a scraper *
plastics, tin foil
yes
---
a scraper *
limescale and water
rings
---
yes
cleaner for glass ceramic
or stainless steel *
fat splashes
---
yes
cleaner for glass ceramic
or stainless steel *
shiny metallic discoloration
---
yes
cleaner for glass ceramic
or stainless steel *
* Scrapers and cleaners for glass ceramic
and stainless steel can be purchased in specialist shops
Remove stubborn residues with a cleaner for glass ceramic or stainless steel.
Scratches or dark stains on the glass
ceramic that cannot be removed do not
however affect the functioning of the appliance.
progress 11
What to do if ...
Problem
The cooking zones will not
switch on or are not functioning
Possible cause
Remedy
More than 10 seconds have
Switch the appliance on again.
passed since the appliance was
switched on
The child safety device is switched on
Deactivate child safety device
(See the section “Child safety
device”)
Several sensor fields were
touched at the same time
Only touch one sensor field
Automatic switch off has been
triggered
Remove any objects (pan,
cloths, etc.) that are lying on the
control panel. Switch the appliance on again
The lock is switched on
Remove any objects (pan,
cloths, etc.) that are lying on the
control panel. Switch the appliance on again
Acoustic signal sounds when
appliance is switched off
The control panel is wholly or
partly covered by objects.
Remove objects.
The residual heat indicator is not
displaying anything
The cooking zone was only on
for a short time and is therefore
not hot
If the cooking zone is supposed
to be hot, call the Customer
Service Department.
The automatic warm up function
is not switching itself on
There is still residual heat on the Let the cooking zone cool down
cooking zone
The highest heat setting is set
The highest heat setting has the
same power as the automatic
warm up function
The heat setting was set using
the sensor field
1. Switching off the cooking
zone
2. Set the cooking zone using
the sensor field
The On/Off sensor field has
been covered up, e.g. by a cloth
Do not place any objects on the
control panel
is lit
Overheating protection for the
cooking zone has been triggered
Switch off the cooking zone.
Switch the cooking zone on
again
and number are displayed
Electronics fault
Disconnect the appliance from
the electrical supply for a few minutes (Take the fuse out of the
house’s wiring system) If after
is disswitching on again,
played again, call the customer
service department
Acoustic signal sounds and appliance switches itself on and
then off again; after 5 seconds
another acoustic signal sounds
If you are unable to remedy the problem
by following the above suggestions,
please contact your dealer or the Customer Care Department.
Warning! Repairs to the appliance are
only to be carried out by qualified service
engineers. Considerable danger to the
user may result from improper repairs.
12 progress
If the appliance has been wrongly operated, the visit from the customer service
technician or dealer may not take place
free of charge, even during the warranty
period.
Disposal
The symbol
on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Installation Instructions
Safety instructions
Warning! This must be read!
The laws, ordinances, directives and standards in force in the country of use are to be
followed (safety regulations, proper recycling
in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to
other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers
may only be installed with a protective floor
directly underneath the appliance. The cut
surfaces of the worktop are to be protected
against moisture using a suitable sealant.
The sealant seals the appliance to the work
top with no gap. When building in, protect the
underside of the appliance from steam and
moisture, e.g. from a dishwasher or oven.
Avoid installing the appliance next to doors
and under windows. Otherwise hot cookware may be knocked off the rings when
doors and windows are opened.
Warning! Risk of injury from electrical
current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of
voltage.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to
the electrical supply by a qualified
electrician.
Warning! Risk of injury from electrical
current.
• Loose and inappropriate plug and
socket connections can make the terminal overheat.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or twophase connection, the appropriate
mains cable of type H05BB-F Tmax
90°C (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a special
cable (type H05BB-F Tmax 90°C; or
higher). The latter is available from the
Customer Care Department
A device must be provided in the electrical
installation which allows the appliance to be
disconnected from the mains at all poles with
a contact opening width of at least 3 mm.
Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are
to be removed from the holder), earth leakage trips and contractors.
progress 13
Assembly
1
2
min. 500mm
min.
50mm
60
0
1
49
0+
75
0+
1
R5
PAS 8060 E
55HBD47AO
949 593 001
230 V
50 Hz
7,0 kW
PROGRESS
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
14 progress
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number
(S No. - see rating plate)
– Type of fault
– Any error messages displayed by
the appliance
– three digit letter-number combination
for glass ceramic
progress 15
www.progress-hausgeraete.de
867 201 555 -A- 19022008 - 01
Download PDF

advertising